Search Documents

By T. A. Utigard

To improve recoveries of Ni, Cu and Co in the Inco flash furnace, a new operating concept was investigated. By adding sufficient coke to form a supernatant coke layer, a reducing barrier would form allowing for improved reduction of descending oxidized sulfide mineral particles formed in the flame. The objective of this investigation was to study the kinetic mechanism and efficiency of the coke layer to produce a sulfur deficient matte. The mechanism and rate of carbon reduction of each of the phases formed in the flash flame, i.e. sulfides and oxysulfides were investigated by means of X-ray visualization tests. Graphite-slag reduction was also conducted for comparison purposes. In the case of slag, poor wettability and the formation of a gas film on the surface of the carbon reductant are often blamed for limiting the reaction surface area that ultimately results in poor reaction kinetics. The X-ray visualization tests confirmed that matte and oxysulfide wet coke better than slag and that the rates of reduction of matte and oxysulfide are faster than that of slag.

Jan 1, 2005

By Douglas A. Sloan

AN INCENTIVE or bonus system of payment is commonly used for mine labour. The incentive rates are usually based on the variable units of production, such as dollars per foot of drift advance or cents per ton of ore broken. Portions of the work that must be done to achieve the units of ?production are independent of the production unit and tend to be fixed work for the shift or for the job, irrespective of the production achieved. This fixed work has considerable influence on the equity of incentive rates. The effect of fixed work is to accelerate the loosening or tightening of rates if the production task is over-achieved or under-achieved, and of increasing the loosening of rates loosely set and the tightening of rates tightly set. This gearing of mine contract rates is the reason why changes in conditions, materials, equipment, or methods will change the incentive earnings to a greater degree than would normally be expected. Obviously, therefore, care should be taken in the setting of the task for incentive rates as the gearing makes an inequitable rate even more inequitable.

Jan 1, 1958

By J. I. Carroll, J. A. Walker

"Abstract - Camelback is a small (=200 000 tonnes), moderate grade (5%-7% Zn+Pb), volcanogenic massive sulfide deposit, which occurs within the Nepisiguit Falls Formation of the Ordovician Tetagouche Group. The host rocks are tuffaceous sedimentary rocks (Little Falls member) that overlie quartz-feldspar porphyritic tufflavas (Grand Falls member). The hanging-wall sequence comprises rhyolite of the Flat Landing Brook Formation, overlain by the Forty Mile Brook tholeiitic basalt. A dike of unaltered andesite was intersected beneath the massive sulfides, but was not found in the hanging-wall sequence in the vicinity of the deposit. The stratiform part of the deposit is made up of two, steeply south dipping, subparallel massive lenses that average approximately 4 m in thickness. Each lens is zoned, with an upper part consisting mainly of a pyrite and a basal part containing pyrite, sphalerite, and galena, with Ag values. The Au content in the massive sulfides is low (average = 52 ppb for 271 samples), but tends to be enriched in the massive pyrite near the top of each lens. Oxide facies iron formation is spatially associated with the massive sulfides, and has been traced up to 1800 m along strike. Footwall hydrothermal alteration is typical of VMS systems, and is characterized by depletion in K2O and Na2O, and enrichment in MgO and Fe2O3T with proximity to massive sulfides. The massive lenses are underlain by intensely chloritic, fine-grained, tuffaceous sedimentary rocks containing locally significant sulfide (chalcopyrite > pyrite > pyrrhotite) veins, which are interpreted to represent feeder zone mineralization. Unlike many VMS deposits, there is no evidence of silicification beneath the massive sulfides at the top of the feeder zone. The oxygen isotopic compositions (d18O = -1.5‰ to -0.3‰) of hydrothermal chlorite coupled with sulfur isotopic compositions (d34S ˜ 12‰) of the massive sulfides suggest that seawater was the dominant fluid in the hydrothermal system. Normalized rare earth element diagrams show flat Ce profiles and positive Eu anomalies, indicating that modified seawater was involved in ore formation; i.e., high-temperature (=350ºC), acidic, and reduced prior to entrainment into the hydrothermal cell. Although, seawater was the dominant fluid in the sulfide-forming system, d34S values of stringer zone sulfides (8.5‰) coupled with elevated Sn (400 ppm) in one massive sulfide sample indicate that there was at least some magmatic component in the hydrothermal cell."

Jan 1, 2006

By W. H. Miller

Introduction In this paper we have endeavoured to present a general description of the electrical applications underground at Copper Mountain, including types of equipment used, problems encountered, and methods by which they were overcome. No attempt has been made to outline in detail the wiring of various circuits. Until recent years, the main use of electrical energy underground at Copper Mountain consisted of direct current for locomotives, trolley systems, .and signal and communication circuits. The prohibitive cost of equipment and distribution systems prevented any extensive use of a.c. beyond that commonly used for essential lighting purposes. However, in 1943 the shortage of manpower and the increased cost of labour and supplies necessitated a general mechanization programme.

Jan 1, 1951

By P. -A. Bosse, J. Robitaille, P. Blatter

The LaRonde ore is a Cu-Zn-Pb ore with gold (3-4 g/t) and silver (60-100 g/t). The precious metals are recovered with copper concentrate, zinc concentrate and cyanidation of zinc tails via Merrill Crowe precipitation. Subsequent to a recent mill expansion, excessive gold was reporting to zinc concentrate with a concurrent decrease in gold to copper concentrate. Owing to the higher return obtained from the metal, the mill endeavors to recover additional gold and silver to the copper concentrate and minimize the placement of precious metals to the zinc concentrate. A gold deportment study showed that the gold occurs mainly as küstelite, with a moderate amount of electrum and a minor amount of native gold. It also showed that various sulfur-based Au-and/or Ag-bearing coatings on liberated küstelite and electrum were the major mineralogical factors that caused gold and silver to report to zinc concentrate. By frequency, such coatings were observed on 70-80% of total liberated gold particles reporting to the zinc concentrate. Based on the gold deportment and the chemistry of the coatings, the collector chemistry was reviewed and a new collector was added into the circuit which resulted in a significant increase in gold and silver recovery to the copper concentrate. The information obtained from the mineralogy confirmed and guided other process optimization. In this paper, the authors will describe the process mineralogy of the LaRonde ores, and in particular, the mineralogical evidence diagnosing the problem. Reference will also be made to the rationale behind how the problem was solved, the results achieved, and future steps in optimization.

Jan 1, 2005

By Allan A. Este, Bruce Arthur

"Rio Algom's Stanleigh Mine and Mill Operation Was' officially started up in August 1983. In September 1982, Rio Algom contracted Estonix International Inc. from Lively, Ontario, to develop and implement two innovative programs: (1) Work Renovation Planning, and (2) Systems Performance Training. This paper deals with the development and implementation of these two concepts relative to the plants technology from start-up to present and the exceptional results achieved. This paper discusses how a small but motivated workforce resulted in the smooth transition from startup to full production. It also deals with how these concepts were applied elsewhere in the organization which permitted a successful transition and downsizing of the over-all operation.IntroductionRio Algom Limited produces uranium in Elliot Lake, Ontario. In the late 1970s Rio Algom entered a contract with Ontario Hydro to supply uranium from its Stanleigh property, which had been idle since 1960. The mine was subsequently upgraded, and a new modem mill was designed and built, commencing operation in 1983.From then until September 1990,Rio Algom had three producing mines and mills in the Elliot Lake area. Quirke mill, with a capacity of 6350 tonnes per day, operated continuously from 1968. The Panel mill with a 3000 tonnes per day capacity, operated since 1979. Stanleigh mill continues to operate under long-term contracts, although at a production rate about 25070 lower than its rated capacity of 5000 tonnes per day.Both the Quirke and Panel mills, although not entirely similar, were conventional uranium mills utilizing crushing, grinding, leaching and ion exchange. As such, and in keeping with the traditional management style, there was a rather large mill operating workforce, which utilized a line-of-progression job classification system."

Jan 1, 1993

By Pierre Sauvé, Alex Makila

"The Camflo stock of porphyritic quartz syenite is an irregular pipe-like body 200 metres in diameter injected along the axial plane of an E-W trending F2 fold, near the contact between the. Kewagama and Malartic groups. The stock plunges 55° to the NE, almost parallel to the fold axis. The stock, exhibiting pervasive, weak cataclasis with numerous, locally auriferous quartz veinlets, is cut by minor faults striking WNW and dipping about 45°NE.Two types of gold ore are distinguished at Camflo: ""porphyry"" ore and ""fault zone"" ore. ""Porphyry"" ore, accounting for 90% of the gold produced, forms wide zones within the stock. The zones are irregular in shape but tend to be oriented E-W in plan view (on a horizontal plane) and are elongated paraliel to the plunge of the stock. These zones are more abundant in the northern part of the stock. Differences between ore and barren porphyry are not obvious. ""Fault zone"" ore occurs outside the stock along minor faults, particularly in differentiated sills offer rodiorite and felsic granophyre. Gold grade is roughly proportional to the pyrite content which in turns depends in part on the original magnetite content of the host rock. Although both types of ore show some correlation between Au and S, the Au/S ratio is considerably higher in porphyry ore.The bulk of the gold is in quartz syenite and in felsic granophyre, the most brittle lithologies at the mine. Presumably, the vertically continuous, pipe-like stock, made up of shattered rock, provided the main channelway for the ascending mineralizing solutions."

Jan 1, 1990

By E. Barnard, J. Tero, J. Rajala, N. Avenido, M. Fullam, A. Nashitati, S. Mbalamba

"The Otjikoto mining and milling complex is 90% owned by B2Gold Corporation, and began commercial operation on February 28, 2015. The milling circuit operates at a throughput 3.3 million tonnes per annum, with an average reserve gold grade of 1.28 g/t. The ore is high in Gravity Recoverable Gold (GRG), which varies between 73-91%, depending on ore type. Overall gold recovery since start-up is 98.2%, with about 63.5 % coming from the gravity circuit as doré. 2016 cash operating costs, and all in sustaining cost (“AISC”) were $361 and $604 per ounce, respectively.During design, three ore types were tested for GRG content, and based on the high GRG value of all three ore types, the decision was made to treat the full ball mill circulating load by gravity. Once operating, the gravity circuit performance was characterized by performing a detailed gravity audit, which included the ore, cyclone classification, Knelson concentrators, and the Consep Acacia intensive leach system. The deeper ores contain significant pyrrhotite, and this created some unusual challenges that had to be overcome. This paper presents the gravity circuit design process, the circuit commissioning, and the audit results and ongoing improvements.IntroductionHeadquartered in Vancouver, Canada, B2Gold Corp. was founded in 2007. Currently, B2Gold has five operating mines, and numerous exploration projects in various countries, including Nicaragua, the Philippines, Namibia, Mali and Burkina Faso. The Otjikoto Mine is located in the north-central part of the Republic of Namibia. It is situated approximately 300 kilometers north of Windhoek, the country’s capital, within the Province of Otjozondjupa. The Otjikoto mining and milling complex is 90% owned by B2Gold Corporation, and began commercial operation on February 28, 2015. The milling circuit operates at a throughput 3.3 million tonnes per annum. During design, a large emphasis was placed on gravity recovery, as the Otjikoto ores are unusually high in Gravity Recoverable Gold (GRG)."

Jan 1, 2018

By \/eena Sahajwalla, Jonathan Dicker, Paul O'Kane, Cath Skidmore, James Dankwah, Magdalena Zaharia, Rita Khanna, David Knights, N Saha-Chaudhury, Somyote Kongkarat

Due to the inherent limitations of current methods of disposal of end of life polymeric materials, avenues are researched towards developing alternative, environmentally friendly and economic recycling processes. Different polymeric materials (i.e. rubber, high density polyethylene (HDPE) and polyethylene therephtalate (PET)), quite distinct in terms of chemical structure and composition, were considered in the present study as carbon resources in EAF steelmaking. Investigations were conducted in both laboratory and industrial scale steelmaking to assess the effectiveness of using these materials as carbon sources for slag foaming in EAF steelmaking. Slag foaming is important because it enhances furnace efficiency.

Jan 1, 2011

By A. R. Hekmat

Hypereutectic Al-Si alloys are used in applications that require high resistance to wear and corrosion, hardness and low coefficient of thermal expansion, To maximize the properties of these alloys, semi-solid processing can be utilized to modify the solidification structure of the primary silicon crystals as well as to reduce microsegregation and porosity, The transformation and spheroidization of primary Si crystals by shearing in the semi-solid state are not fully understood as they precipitate in the presence of other alloy phases, The objective of the present work is the determination the rheological characteristics of A390 (Al-17%Si-4,5%Cu-0.5%Mg) alloy using a Couette type (Haake RV12) viscometer and examining the microstructural evolution during continuous cooling and isothermal shear rate experiments, The effect of shear rate, solid fraction (temperature) and morphological evolution of the silicon crystals are investigated.

Jan 1, 2005

By C. A. Morais, L. V. Resende

"The technological development observed in recent years has stimulated the application of rare earth (RE) elements. Amongst their various applications it is well worth mentioning their use in electronics, superconductors, nuclear medicine, as well as in special inks - as those used in radar invisible airplanes. TV and computer monitor screens present as coating a powder containing some rare earth elements, mainly Europium and Yttrium. The recovery of the RE elements from electronic scrap is extremely important as the economic and environmental issues are concerned. This paper describes the study of the Eu and Y recovery from e-scraps. The first step of the process was the leaching of the powder obtained by manually scraping the inside surface of the screen. After the optimization of the leaching, the dissolution of Eu and Y was higher than 98 w/t% and a pregnant sulfuric liquor containing 11.9 g L-1 Y and 0.72 g L-1 Eu was obtained. The second step was the separation of the metals found in the liquor by the solvent extraction technique. The separation of Eu and Y was carried out in a counter current circuit compound of 3 extraction stages, 7 scrubbing stages and 15 stripping stages. DEHPA was used as the extractant, whereas a diluted sulfuric acid solution was applied as scrubbing agent and a hydrochloric acid solution at high concentration was used as the stripping agent.INTRODUCTIONThe rare earths (RE) are a moderately abundant group of 17 elements composed of lanthanides, scandium and yttrium. Amongst the RE, promethium (Pm) is extremely rare, however several of the RE elements are not very rare and occur dispersed in a variety of forms (Greenwood & Earnshaw, 1984; Tyler, 2004).The innumerable applications of the RE elements are based on their particular properties, mainly their spectroscopic and magnetic properties (Martins & Isolani, 2005). The technological development observed in recent years has stimulated the application of rare earth (RE) elements. They have been used in agriculture, electronics, superconductors, nuclear medicine, automobile industry, special inks – as those used in radar invisible airplanes, X-ray screens, high intensity mercury vapour light bulbs, neutron scintilators, charged-particle detectors and optical memory reading systems (Maestro & Huguenin, 1995; Nagaosa & Binghua, 1997; Sánchez et al., 1999)."

Jan 1, 2012

By Clifford S. Gibson

THESE troubled times suggest three reasons for maximum effort to control silicosis: (1) To keep to a minimum the ever-increasing burden occasioned by past deficiencies in this respect. (2) To effect the greatest production with maximum efficiency, which means at the least cost. (3) To preserve man-power in every way. Good control of the silicosis problem aids these aims. Inadequate control hampers all three. Insofar as our knowledge goes, silicosis in Ontario mines is caused by the inhalation of finely particulate quartz. It follows, therefore, that removal of dust containing this mineral automatically erases the cause. The achievement of this ideal is the aim of the mine operator. His best tool to this end is ventilation. This paper discusses mine ventilation from the viewpoint of dust control and it is hoped that in so doing there may result a better understanding of the part played by air in silicosis prevention. No attempt will be made to treat the subject fully. Instead, there will be presented certain salient aspects culled from field observations, the data in all cases referring to gold mines, unless mention to the contrary is made.

Jan 1, 1942

By H. J. McQueen

Before 1950, hot working was simply deforming above the recrystallization point and gave a soft product compared to cold working. From 1960 onwards, improved testing in compression and torsion (stress, strain rate, temperature, quenching) provided valid specimens for microstructural analysis by polarized optical and transmission electron microscopy (TEM). Indeed, TEM was essential to uncovering the hot working mechanisms because it could distinguish between cold and hot substructures (dynamic recovery) in either initial or new grains (dynamic recrystallization). Over the years, teams at Concordia, McGill and UBC obtained NSERC support for students and equipment. CANMET built up a hot forming group having capabilities from high-rate cam-plastometer compression to rolling of experimental alloy billets; this was combined with latest metallographic instruments for fundamental research. Al alloys of every class (2000, 3000, 5000, 7000, 8000) were studied to understand the effects of solutes, precipitates, dispersoids and composites. The complex flow patterns in extrusion were clarified and modeled by finite element methods. Physical simulations of rolling schedules (up to 20 passes and reductions of 98%) by torsion provided evidence of microstructure development during both the passes and the softening intervals, thus clarifying development of texture in different alloys. The results frequently appeared in proceedings of Light Metals symposia and Canadian Metallurgical Quarterly

Jan 1, 2011

By S. Parkash, A. J. Szladow

Vigorous agitation of suspensions of coking coals in water (or light mineral oils) will often result in catast rophic loss of caking properties. It is shown that this deterioration is not a consequence of oxidation of the coals (by dissolved oxygen), but that it can be qualitatively connected with internal "solid-state" reactions which appear to derive their activation energies from cavitation of the liquid.

Jan 1, 1971

By J. Kempken, R. Hagmann, C. -P. Reip, W. Hennig

The CSP technology symbolizes a highly productive process for the cost-effective production of steel grades with a range of sophisticated properties comprising both the inner quality of hot strip, its surface formation as well as the relating technological characteristics. Thanks to extensive development work undertaken during the last 15 years, the range of steel grades that can be produced was continuously expanded and the process technology optimized. The present paper describes the ongoing development work concerning the production of higher-strength, microalloyed pipe steels. The resulting hot strip, due to the associated thickness and the potential pipe diameters, is particularly suited for being processed to HFI-welded pipes. Based both on ferrite-pearlite as well as very fine-grained, ferrite-bainite hot-strip microstructures, strength levels of up to grade API X80 can be realized. It can be demonstrated that hot strip produced in a CSP plant has very good toughness values at temperatures down to -60°C and can even make application with required sour-gas resistance possible.

Jan 1, 2005

By H. W. Wevers

This paper is the result of an intensive literature search and practical study of the problems experienced by a mining company with the frame cracking of their large-tonnage haulage trucks. It explains the advantages of particular HSLA steels for applications in the welded structures of such equipment. Examples of existing welds in truck frames are analyzed. Modern fatigue models and linear elastic fracture mechanics techniques are explained.

Jan 1, 1978

By T. Y. Chong, J. A. Folinsbee

Since milling began in 1909, the PJV Dome mill has been expanded several times, to the current throughput of 11,500 tonnes per day. PJV recovers free gold using crushing and grinding followed by gravity concentration. The remaining gold in the gravity tails is recovered by cyanide leaching followed by Carbon-In -Pulp processing. Prior to 1993, cyanide tailings were impounded in the tailings pond where cyanide was allowed to degrade naturally. Effluent was discharged seasonally during the summer and early autumn to maintain the water balance. In 1993, an Effluent Treatment Plant (ETP) was designed and constructed for the purpose of removing dissolved metals and suspended solids. In 1997, an INCO SO2/Air cyanide destruction process was added to the ETP. Even though the ETP was successful in meeting the cyanide, metals and total suspended solids (TSS) discharge limits, often the treated effluent failed to pass toxicity tests. Following successful laboratory and plant scale testing, the addition of the chelant EDTA (ethylene diamine-tetra-acetic-acid) was commenced in the 1999 operating season. To date, discharged effluent has passed all toxicity tests. This paper describes the evolution of the ETP from its early conception to the various phases of upgrade needed to meet the MISA discharge limits.

Jan 1, 2005

By Robert A. Creaser, David R. Lentz

Abstract - The Moss molybdenite deposit, which was mined during both world wars, is hosted in late Grenvillian granitic pegmatite dikes. These dikes are locally aplitic, and intrude the late tectonic Onslow syenite (probably correlative with the ~1090-1070 Ma Kensington suite), which is in turn intrusive into the 1170-1155 Ma Chevreuil intrusive suite of southwestern Quebec. A Re-Os model age of 1053 ± 4 Ma (8.3 ppm Re) was obtained for molybdenite from a pegmatitic veinlet within an aplitic phase of the dike. A much younger Re-Os date of 860.9 ± 9.2 Ma (6.9 ppm Re) obtained previously from a pyrrhotiteand pyrite-rich metasomatic vein might reflect Os diffusion during slow cooling of the Grenville province, because this age is consistent with K-Ar dates reported from the region. Alternatively, the similarity between these younger dates may be fortuitous, and may instead relate to sampling issues for molybdenite. The Mo-rich granitic dikes at the Moss deposit are similar to other Mo-rich A-type pegmatite-aplite granitic dike systems that formed immediately after the peak of the Ottawan orogeny (1070-1090 Ma), and possibly are more closely related to the Kensington suite than previously thought.

Jan 1, 2005

By Simon C. Dominy, Alwyn E. Annels, Paul Wheeler, Suzanne P. Barr, G. Simon Camm

Narrow veins are an important world-wide source of silver, tin, uranium and particularly gold. To potential ?nanciers, this style of mineralization is viewed as high risk because of the often relatively small resource involved and high cost of estimation. In many cases diamond core drilling will not enable resource estimation beyond the inferred and indicated categories. Exploratory under-ground development is required to de?ne measured resources. The de?nition of geological and grade continuity are major factors in narrow vein assessment. A measured resource must be based on strong geological and grade continuities. Narrow veins, generally less than 3 m wide, are complex geological phenomena, which commonly display unpredictable geometry and grade distribution. Variations in structural continuity, dip, strike, width, mineralogy and speci?c gravity are common. Veins may be composite, with ore-grade mineralization restricted to a speci?c structural domain. Branches, intersections and braided zones are common features. Potentially high-grade zones are often localized within ore shoots, which are surrounded by barren/low-grade regions. Resources must be determined as closely as possible to reality and re?ect the distribution of the commodity in the rock. Estimation has three main requirements: (1) geological study to determine orebody nature;(2) estimation of tonnage and grade, and (3) the presentation of this information using a classi?cation that is clear, unambiguous and bankable. Estimation methods employed are either classical or geostatistical; however, classical methods are often used because of the dif?culties in applying geo-statistics. Grades generally show a strong positively skewed distribution testifying the presence of high-grade values. Problems exist in the applicability of cutting outlier values risking over- or under-estimation of grade. It is generally believed that where resource estimates are in error, poor geological control is usually the cause. Overestimation can lead to the closure of a mine through lost revenue and capital. An understated estimate can result in an opportunity missed for pro?t and/or greater economies of scale. De?nition of reserves involves the consideration of economic and engineering data, to decide which part of the resource is economically mineable. Geology plays a similarly important role at this stage in the assessment of likely mining method, dilution, recovery etc. Throughout resource/reserve estimation, it is crucial that the amount and quality of the data and the geologist’s experience are relevant. The impact of geological understanding on estimation is often undervalued or assumed to be of lesser importance than ?nding grades and tonnages. This paper discusses the geology of narrow vein deposits and the importance of geology in their evaluation.

Jan 1, 1997

By Simon C. Dominy, Alwyn E. Annels, Paul Wheeler, Suzanne P. Barr, G. Simon Camm

Abstract-Narrow veins are an important world-wide source of silver, tin, uranium and particularly gold. To potential financiers, this style of mineralization is viewed as high risk because of the often relatively small resource involved and high cost of estimation. In many cases diamond core drilling will not enable resource estimation beyond the inferred and indicated categories. Exploratory underground development is required to define measured resources. The definition of geological and grade continuity are major factors in narrow vein assessment. A measured resource must be based on strong geological and grade continuities. Narrow veins, generally less than 3 m wide, are complex geological phenomena, which commonly display unpredictable geometry and grade distribution. Variations in structural continuity, dip, strike, width, mineralogy and specific gravity are common. Veins may be composite, with ore-grade mineralization restricted to a specific structural domain. Branches, intersections and braided zones are common features. Potentially high-grade zones are often localized within ore shoots, which are surrounded by barren/low-grade regions. Resources must be determined as closely as possible to reality and reflect the distribution of the commodity in the rock. Estimation has three main requirements: (1) geological study to determine orebody nature; (2) estimation of tonnage and grade, and (3) the presentation of this information using a classification that is clear, unambiguous and bankable. Estimation methods employed are either classical or geostatistical; however, classical methods are often used because of the difficulties in applying geostatistics. Grades generally show a strong positively skewed distribution testifying the presence of high-grade values. Problems exist in the applicability of cutting outlier values risking over- or underestimation of grade. It is generally believed that where resource estimates are in error, poor geological control is usually the cause. Overestimation can lead to the closure of a mine through lost revenue and capital. An understated estimate can result in an opportunity missed for profit and/or greater economies of scale. Definition of reserves involves the consideration of economic and engineering data, to decide which part of the resource is economically mineable. Geology plays a similarly important role at this stage in the assessment of likely mining method, dilution, recovery etc. Throughout resource/reserve estimation, it is crucial that the amount and quality of the data and the geologist’s experience are relevant. The impact of geological understanding on estimation is often undervalued or assumed to be of lesser importance than finding grades and tonnages. This paper discusses the geology of narrow vein deposits and the importance of geology in their evaluation.

Jan 1, 1997