Search Documents

By Joseph J. Larry

In hard siliceous sandstone strata overlying coal seams, roof bolting is often the bottleneck in the coal production cycle. In the past, these strata have been drilled by pneumatically operated stopers. Although slow drilling is cumbersome and uncomfortably noisy, the stoper was the most effective drill in these harder strata. However, because of the (U.S.) Coal Mining Safety Act, which limits noise levels for operating drills, FMC Mining Equipment developed the water-through-the-drill-steel method of drilling high-compressive-strength strata. Although water-through-the-drill steel had been developed earlier, the real impact of wet drilling techniques surfaced when the dual-boom roof drilling machines were installed at the Virginia-Pocahontas Division, Keen Mountain, Virginia, in 1974. This paper covers some of the technical details of the water-through- the-drill-steel design and its application.

Jan 1, 1979

By Stephen Hardcastle

Presentation Outline ? Introduction ? Mine Ventilation Facts ? Ventilation-on-demand (VOD) ? Sensors/Controls ? Continuing Work ? Conclusions ? Mine ventilation engineering practices were published in 1556 in Agricola?s De Re Metallica (wind sails, bellows, etc.) That was then? This is today? Large fan installations handling >1M cfm

Nov 1, 2011

By P. M. Dranchuk

"""PLANET EARTH seen from space appears as a fragile and limited life-supporting system in a vast emptiness. That such a view is, in fact, an accurate one is now more widely accepted than it was not long ago, before Earth's problems of over-population, overconsumption, limited resources and environmental degradation attained the limelight. The danger is that a government and public now deluged by doomsday prophecies and bemused by equally confident reiterations that technology will cure all may hesitate in coming to grips with the problem, in the hope that, given time, it will go away."" With these words, Preston Cloud begins a recent editorial, in Science(l), in which he presents a brief resume of some of the findings of the Committee on Resources and Man of the National Academy of Science-National Research Council(20.Their report, which is based on a two-year study by an extremely competent group and consists of some 250 pages of text, is even more far-reaching and sobering than the report on Energy Resources(3). It begins by quoting Sir Macfarlane Burnet as follows:""There are three imperatives: to reduce war to a minimum; to stabilize human population, and to pre-vent the progressive destruction of the earth's irreplaceable resources.(4)"

Jan 1, 1971

By J. G. Thomson

Development of the Canadian North, a subject of growing national interest, must in part await the development of better forms of trans-port. The estimated 500,000 square miles of muskeg terrain in the north combined with the" scarcity of roads make essential the early development of special purpose muskeg vehicles. Good progress has been made in the last eleven years in classifying muskeg and some progress has been made in determining its mechanical properties. Limited travel is now possible through the use of special purpose tracked vehicles which have been built without adequate design data. A program to provide data which can be used to optimize muskeg vehicle designs began in 1957. The results of the second phase of this pro-gram are presented in this report. It is shown that vehicle performance in muskeg is directly related to the mechanical properties of the muskeg. Further, it is shown that good de-sign practice for tracked vehicles expected to operate in snow, sand, soft clays and loams is also good practice for muskeg vehicles. All indications are that muskeg mechanics is properly a part of conventional soil mechanics.

Jan 1, 1961

By L. S. Almeida, U. A. Courbassier, C. T. Guimãaraes, M. N. Souza, V. L. Silva, H. P. Dias, G. A. Bicalho, B. S. Rocha, P. N. Rodrigues, A. Carnevale

During primary aluminum production the anode changing is a very important task. So improvements on it will be essential to avoid disturbance and have a better operational control. After anode changing a good current distribution will be guaranteed using a cavity cleaner and precise anode setting. Albras switching a manually anode setting to an automatic one solved the setting problems. In this paper it will be shown some pot line results and the improvements on workers ergonomic and safety conditions. The device was developed in a partnership between Albras and Pesto.

Jan 1, 2006

By O. Leuangthong, E. Schnetzler

"The McMurray formation in the Athabasca oil sands deposits of northern Alberta is part of the world’s second largest proven crude oil reserves. The formation is characterized by stratigraphic layers that correspond to three different depositional environments: Marine, Estuarine, and Fluvial facies. Resource estimation for oil sands has traditionally relied on polygonal and inverse distance schemes. These techniques are simple and straightforward in practice, but they do not permit reliable uncertainty assessment. This paper describes the modelling of the McMurray formation using modern geostatistical techniques.Geostatistical modelling should be performed within homogeneous geological facies. The methodology for geostatistical simulation within each of the identified facies involves: 1) assessing the most appropriate stratigraphic transformation for optimization of the correlation structure; 2) determining representative distributions with declustering and debiasing techniques; 3) modelling spatial continuity of the bitumen grade, fines grade, water saturation, and other petrophysical variables; 4) performing estimation and cross validation as checks against simulation results; 5) performing simulation for uncertainty quantification of bitumen and fines grade; and 6) model checking of simulation results against the input data, and comparisons against the kriged models. These steps are described in detail. The application of these models for uncertainty quantification in support of resource classification is also discussed."

Jan 1, 2006

By M. H. Haycock

Introduction The property of Rouyn Merger Gold Mines, Limited, is in Rouyn and Joannès townships, Western Quebec, seven miles east of the town of Rouyn. Traversing it is the east-west trending Cadillac-Bouzan fault. Diamond drilling in 1944 and 1945 along a shear zone south of the fault indicated an ore deposit lying at the contact between sedimentary and volcanic rocks and dipping approximately 60° to the northwest. In the summer of 1945 it was decided to sink a shaft to investigate the indicated ore zone. In the immediate vicinity of the deposit, bed-rock is overlain by clay beds, in some places as much as 70 feet thick. Consequently, possible shaft sites were limited to those locations where overburden would not be excessive. The most favourable site was about 125 feet to the south of the ore zone as projected vertically from bed-rock to the surface. Accordingly, it was decided to sink the shaft at this point, with an inclination of 60° N. W., paralleling the dip of the ore zone.

Jan 1, 1948

By P. Reyes

The start up and operational optimization of the No. 3 Oxygen Plant at the Caletones Copper Smelter of the Codelco - Chile El Teniente Division is summarized. In addition, the economic impact of such optimization on the production cost of oxygen and others aspects associated to the operational robustness as well is detailed.

Jan 1, 2007

By M. El Tokhi, H. Arman, B. M. Amin

"This paper aims to overview some mechanical and physical features of the gabbroic rocks. The study has two phases: filed study/in-situ measurements and laboratory work. During the field studies, rock block samples were collected from different locations of the study area to represent the different types of the gabbroic rocks. Either core or rock samples for various tests were prepared from rock samples taken to the laboratory. The unconfined compressive strength (UCS), indirect tensile strength (ITS), point load index (PLI), Schmidth hammer rebound value (SHV), slake durability index (SDI), sonic velocity (SV) and unit weight (UW) test were carried out either on the selected rock block samples or core samples.INTRODUCTIONThe geology of the United Arab Emirates (UAE) has been divided into three major rock units (Lippard et al., 1986); an autochthonous succession, allochthonous units composed mainly of Mesozoic rocks and include the Sumeini Group (concomittent slope sediments), Hawasina Complex (basinal sediments) and the Semail ophiolite nappe (massive slice of former oceanic crust), that were emplaced as a series of thrust nappe in the Late Cretaceous and Neo-autochthonous sequence of Maastrichtian and Lower Tertiary sediments.The Semail Ophiolite (600 km long and up to 150 km wide) is thought by some authors (Glennie et al., 1990) to have been generated along a subduction related back-arc spreading axis during the Cenomanian-Turonian and was obducted onto the Arabian continental margin during the Campanian. Others, however, consider it to represent a primitive arc-spreading center related to oblique subduction Lippard et al., 1986). The Ophiolitic rocks in the study area comprise mantle and crustal sequences. The mantle peridotite and crustal gabbros are the dominant rock types of the exposed Semail Ophiolite north of the Hatta zone. This paper is only concentrated on the gabbroic rocks."

Jan 1, 2015

By H. O. Seigel

Induced Polarization includes many types of dipolar charge distributions set up by the passage of current through consolidated or unconsolidated rocks. Among its causes are concentration polarization and electrokinetic effects in all rocks and the phenomenon of Overvoltage in rocks containing electronic conductors such as metallic sulphides and graphite. In normal rocks the polarization effects may be usually con-fined within relatively narrow limits and any large departures may be at-tributable to the presence of electronic conductors. In practice, Induced Polarization is measured in one of two ways. In the first a steady current of some seconds duration is passed and abruptly interrupted and the slowly decaying transient voltages existing in the ~round are measured after interruption. This is known as the "pulse", "transient", or Direct Cur-rent Induced Polarization (D.C.I.P.).The second method entails a comparison of apparent resistivities using sinusoidal alternating current of two or more frequencies, generally within the range of 1/10 to 10 c.p.s. Induced Polarization extends the

Jan 1, 1962

By E. Swartzman

"IntroductionGENERALLY, the necessity for mining coals of higher impurity content, the drive for lower costs by intensive mine mechanization, changing market requirements, and the increasing competition of oil and natural gas, have continued to result in an upward rise in coal preparation, and have necessitated a more intensive study of coal preparation problems.Increasing adoption of •continuous mining equipment, for example, is introducing new problems in coal preparation. Limited experimental work in the United States (1) shows that the effect of the continuous miner on size distribution varies with the characteristics of the seam. In some seams, the fines problem is lessened, in others it is greatly aggravated. Generally there is a decrease in the relative amount of the top sizes (plus 2 in.) and a substantial increase in the intermediate sizes (down to about 1/8 in.). Contrary to expected results•, where continuous miners with vertical-moving cutting heads are used, an increase in impurities in the slack sizes does not necessarily occur where draw-slate is taken. This is because the draw-slate tends to be kicked out in lump form. However, if a seam contains bands •and lenses of impurities they are bound to be in the mined product."

Jan 1, 1952

By Wm. L. Giachino

"Over the last 10 years, C-1-L has played a significant role in the major advances that have taken place in blasting technology, among them the following: development and introduction of capsensitive slurries; development of bulk slurry systems both for underground and open-pit operations; development of the TOE-DET and ANODET systems of delay blasting;introduction of the NONEL system of initiation;development of the Vertical Crater Retreat (VCR) system of mining.This paper identifies areasin which we foresee further developments in blasting technology over the next 10 years and outlines how and to what extent C-1-L will become involved."

Jan 1, 1980

By Tyler J. Irving

"In June, 2018 Lalor Mine experienced a catastrophic blade failure of its No. 2 main exhaust fan. Over the following weeks several key changes were made to the auxiliary ventilation system to allow for continued production while the exhaust fans were repaired. Issues encountered during the period of reduced ventilation, and how they were addressed, are analyzed. The suspected causes of the exhaust fan blade failure and how risk was mitigated during the reconstruction are discussed. Key findings and lessons learned are summarized.INTRODUCTIONLalor Mine, owned and operated by Hudbay is an underground zinc, gold, and copper mine located in northern Manitoba. The mine workings extend to a depth of 1090 metres below surface and is ventilated using a push-pull system. The mine exhausts through the main exhaust raise; equipped with two, 2,500 HP fans and upcasts through a portal located at the neighboring mine, Chisel North. Air is supplied to Lalor Mine through four intake fans: The Production Shaft Downcast (two, 250 HP), Lalor Downcast (one, 400 HP), and Chisel Downcast (one, 600 HP) fans (Figure 1). In June 2018, Lalor was scheduled to produce approximately 4,000 tpd.On June 20, 2018 at 2:52 pm Lalor Mine experienced a fault on the Variable Frequency Drive (VFD) for Exhaust Fan No. 1. Time would be needed to complete the necessary repairs. The No. 2 exhaust fan was ramped up from 525 rpm to 800 rpm, 90% of its capacity, in order to maintain underground ventilation. At 4:46 pm, approximately two hours after the rpm was increased, exhaust fan No. 2 experienced a catastrophic blade failure. The forces from the blade failure resulted in the top half of the fan housing being thrown 50 metres from where it was installed; with several large sections of fan blade being thrown further (Figure 2)."

Jan 1, 2019

"Energy efficiency in mining and minerals processing has attracted considerable public and industry attention because of the significant quantities of energy consumption involved. In this context the question of what are worthwhile targets for energy efficiency improvements ought to be of the highest priority. It is however worth taking a step back to avoid falling in the trap of taking preconceived ideas that have been reiterated repeatedly before as gospel. The aim of this paper is to highlight areas where new or alternative approaches could potentially be the better way forward. Some may come as a surprise to conventional industry thinking. Ultimately any such solutions are attractive to practitioners not just in an environmental but also in an economic sense, and hence should be targeted through applied research and development efforts. This paper highlights key aspects of each group of opportunities and some of the individual approaches to provide an overview of the current status quo.MINING INDUSTRY POWER UTILISATION – WHERE IS THE BIGGEST BANG FOR THE BUCK?The question of where is the biggest bang for the buck when trying to determine worthwhile targets for energy efficiency improvements has not always been reported on broadly enough, typically because industry practitioners operate in specific areas of expertise and comfort zone. Looking beyond the familiar doesn’t always come easy. Any technology or methodology consideration to address energy efficiency needs to take into account the context of alternative opportunities of superior value or risks not achieving desired uptake. The following sub-chapters have been ordered by magnitude of improvement potential as best as is possible, starting with the biggest first, and the smallest last. Some may be a surprise relative to conventional mining industry thinking."

Jan 1, 2016

By M. Gimpel, R. Galler, T. Antretter, H. Kargl, R. Tichy, W. Ecker, M. J. Mikl-Resch, G. Pittino

"A computational method based on a continuum-mechanical approach to simulate rock cutting is developed and evaluated. The aim is to obtain the local loading acting at the cutting pick during operation. The explicit FEM is chosen to model the pick-rock interaction. The presented method takes advantage of (i) an advanced material model (ii) a robust contact algorithm and (iii) fast calculations due to parallelization. A damage-plasticity law is chosen and modified with user-subroutines. A user integrated element deletion routine evades critical mesh distortions. Infinite elements at the model boundaries avoid unrealistic deformation wave reflection.INTRODUCTIONExcavation in mining and tunneling is a costly and complex process. Special equipment such as the roadheader (Figure 1) is employed to cut the rock in the excavation process but high material strengths limit their usability (Tockner 1999). Nowadays a challenge is to extend their field of application to harder and more abrasive rock materials. The forces on the pick (Figure 2) are of great importance and determine wear and especially the efficiency of the machine. Figure 2 shows the principle of cutting and the predominant forces. The variation of pick geometry, cutting depth or attack angle will result in an alteration of these forces and determine the efficiency of the process (Tockner 1999). The mechanisms of rock cutting follow the principle of indentation (Kou et al. 1999). Directly under the indenter a hydrostatic stress state evolves causing the material to fail only due to crushing and fragmentation mechanisms. In the close surroundings large strains emerge and tensile cracks are formed but in a further distance the material behaves elastically."

Jan 1, 2015

By M. Gimpel, R. Galler, T. Antretter, H. Kargl, M. Mikl-Resch, R. Tichy, W. Ecker, G. Pittino

"A computational method based on a continuum-mechanical approach to simulate rock cutting is developed and evaluated. The aim is to obtain the local loading acting at the cutting pick during operation. The explicit FEM is chosen to model the pick-rock interaction. The presented method takes advantage of (i) an advanced material model (ii) a robust contact algorithm and (iii) fast calculations due to parallelization. A damage-plasticity law is chosen and modified with user-subroutines. A user integrated element deletion routine evades critical mesh distortions. Infinite elements at the model boundaries avoid unrealistic deformation wave reflection.INTRODUCTIONExcavation in mining and tunneling is a costly and complex process. Special equipment such as the roadheader (fig. 1) is employed to cut the rock in the excavation process but high material strengths limit their usability (Tockner 1999). Nowadays a challenge is to extend their field of application to harder and more abrasive rock materials. The forces on the pick (fig. 2) are of great importance and determine wear and especially the efficiency of the machine. Figure 2 shows the principle of cutting and the predominant forces. The variation of pick geometry, cutting depth or attack angle will result in an alteration of these forces and determine the efficiency of the process (Tockner 1999). The mechanisms of rock cutting follow the principle of indentation (Kou et al. 1999). Directly under the indenter a hydrostatic stress state evolves causing the material to fail only due to crushing and fragmentation mechanisms. In the close surroundings large strains emerge and tensile cracks are formed but in a further distance the material behaves elastically."

Jan 1, 2015

By G. A. Vissac

IN THE preliminary design of a coal washery, the most important factor to evaluate is the ash content of the final product. The ash content permissible may be imposed by market demands, but, in the final analysis, sooner or later - as most consumers today are buying coal on a 'heat value' basis - the coal operator has a certain margin of latitude. and the ash content of the coal to be delivered can be determined on the basis of maximum returns and highest profits. A few years ago, the most desirable separation was selected on the basis of the plus-minus 0.10; that is, the most desirable gravity of the separation was selected at the point showing a minimum amount of near gravities in the raw coal. The reason for this was an expected wide error over these near gravities. Today with the recent development of cry accurate, automatically controlled cleaning apparatus, a much larger latitude is possible, and the most desirable gravity of separation can be selected, almost exclusively, on the basis of the economic factors involved. To illustrate these new methods of investigation we shall give two examples, based on actual coals from the western United States.

Jan 1, 1957

By A. McLean, L. Gao, Z. Shi, Y. D. Yang, K. Chattopadhyay, G. F. Zhang

Levitation melting of metals is one of the emerging applications of magnetic and electric fields in liquid metal refining. The varying magnetic field generates induced current inside the metal droplet and leads to the Joule heating effect and Lorentz force against gravity. This contactless process can avoid contamination from the crucible and can be used to produce high-purity materials. Visualization of the levitation melting process is difficult, and thus generally investigated by mathematical modeling. In the present study, a three-dimensional mathematical model of metal levitation was developed using finite element method for proper understanding of the levitation process. The effects of harmonic magnetic field frequency, coils power input, and sample size on levitation nickel droplet were investigated. Temporal evolution of temperature fields were predicted directly though the model. Levitation and balance condition of the droplet were investigated as well.

Jan 1, 2015

By M. Sommerfeld, U. Schwarz-Schampera, B. Friedrich, D. Friedmann

The steadily growing demand for metals and their price increase at metal exchanges make the mining and utilization of marine mineral resources like polymetallic nodules, manganese crusts or sulfide deposits in the near future a viable option to potentially increase the supply of base and precious metals. For a country with low potential to mine land-based resources like Germany, the industrial recovery of metals from marine mineral resources could lead to a decreased dependency on imports. In this study, seafloor massive sulfides from the German license area in the Indian Ocean (Kairei field, Southern Central Indian Ridge) are treated to recover copper and precious metals. The aim of the project is to demonstrate the transferability of existing metallurgical techniques to the raw material of deep-sea massive sulfides. As a starting point to process this unconventional resource, samples from the Indian Ocean are chemically analyzed and mineralogical characterized. A comparison is carried out between the samples and land-based copper resources, to highlight the potential which lies in mining the deep-sea floor. This paper will show the general possibility of applying a two-stage pyrometallurgical process, based on a concentrate smelting operation, followed by a converting operation in lab-scale to the provided samples of massive sulfides. Generated slag from the concentrate smelting and the converting operation are investigated by X-ray diffraction to determine the mineralogical composition. The two-stage pyrometallurgical process is investigated by the thermochemical modelling tool FactSageTM 7.2 to evaluate the phase distribution of relevant elements between the metal, matte, slag and gas phase. The thermochemical boundaries of the pyrometallurgical process are therefore set and the results of the thermochemical study can be used as an indicator for the efficiency of an up-scaled process and the generated amount of side-streams, which need to be further treated or circulated back into the process. INTRODUCTION Seafloor massive sulfides (SMS) are the third kind of discovered deep-sea minerals besides ferromanganese nodules and cobalt-rich ferromanganese crusts (Sharma, 2017). They occur in water depths around 250–4,000 m (Koschinsky et al., 2018). SMS are characterized by a high base metal and sulfide content. They were created by fluid circulation and hydrothermal convection over time (Han et al., 2018). Commonly, areas rich in SMS are associated with hydrothermal vent fields on the seafloor (Keith et al., 2018).

Jan 1, 2019

By J. W. McCammon

WHEN times are booming and metal prices are high, most mining men pay little attention to the industrial mineral industry. However, when metal prices drop and mines close down, many mining eyes begin to scan the less glamorous non-metallic field. For some this proves a temporary diversion, but others find this branch of mining, with its generally more stable conditions, to their liking and enter it permanently. The resulting gradual influx of trained mining men into the industrial mineral industry ?has been one of several factors responsible for the rise in production of non-metallic materials in our Province. Another and ?perhaps the most important factor influencing the production of industrial minerals has been the growth in the population of British Columbia. Because most industrial minerals .are low priced and either heavy or bulky commodities they are normally sold on relatively local markets. Thus the extent of the development of the industrial mineral industry of a region is largely governed by the size of the population and the level of industrialization of that region. This point is well shown by com-paring population and industrial mineral production statistics for 1936, 1946, and 1956 (see Figure 1)9. Note that not only has the overall production rate grown with the population increase, but that the per capita production has risen greatly.

Jan 1, 1958