Search Documents

By I. C. Brown

Introduction Many tables of nomenclature for igneous rocks have been introduced from time to time, and each has its strong proponents. As a result, any discussion of igneous? rocks is apt to prove confusing unless the names used for these rocks are defined. This ?became so obvious to a discussion group, formed by the members of the Geological Survey of Canada in 1948, that an attempt was made to establish a scheme of nomenclature that could be used by any member mapping anywhere in Canada. The writer was asked to co-ordinate the ideas presented by individuals in the discussion group, to arrange them in tabular form, and, later, to distribute copies of the resultant table to Canadian universities, provincial geological surveys, and some other geological discussion groups. Many useful suggestions and criticisms were received, were studied ?by members? of the original group, and, so far as practicable, were incorporated in the scheme of nomenclature. The result is the table presented here. This nomenclature of igneous rocks is at present being used by most members of the Geological Survey of Canada who are working with igneous rocks, and by some Canadian universities. We hope it will be found useful and be more widely accepted. With this idea in mind, certain principles were adopted in drawing up the nomenclature.

Jan 1, 1952

By D. Cronin, A. Plumtree, A. Hosseini

"Crack in corrosion (CIC) linepipe defects are hybrid defects not directly addressed by existing assessment methods. To investigate the collapse pressure of these defects, CIC defects were formed in 508 mm (20 in) diameter, 5.7 mm thick API X52 linepipe. These defects were 200mm long and varied in depth from 3.0 to 3.8 mm. The respective failure pressures decreased from 14.3 MPa for the plain pipe to 7.9 and 6.2 MPa respectively. A standard FAD method was applied to evaluate these defects as equivalent length and depth cracks, predicting the rupture pressure conservatively by 18% on average. However, when assessed as equivalent cracks with a reduced wall thickness corresponding to the corrosion depth, the predicted collapse pressures were more accurate, approximately 14% conservative on average.INTRODUCTIONPipelines are a safe and efficient method for transporting high volumes of oil and gas. However, aging pipelines may experience defects, such as cracks or corrosion. Present approaches include detection, assessment and repair of defects before they may become critical to the integrity of the line. There are different codes and standards for assessing pipeline defects, depending on the type of defect, with API 579 (API, 2000) being the most common code for the assessment of cracks in oil and gas pipelines . Corrosion is commonly assessed using RSTRENG (Kiefner & Vieth, 1989). Other methods such as the Finite Element method and the CPS method (Cronin & Pick, 2002) may be used for crack and corrosion, respectively.At present, there is no specific method or procedure for assessing crack in corrosion (CIC) defects, and as a consequence there is a need to provide an assessment and evaluation of the integrity of these defects in order to determine the requirements for defect repair or hydro line testing. Hence, the goal of this study was to provide guidance for the assessment of CIC defects for linepipe.CRACK IN CORROSION DEFECTS (CIC)Significant amounts of corrosion and cracking are not generally found together (Hosseini, 2010). However, a new hybrid defect including cracking within corrosion (CIC) has been identified in operating pipelines. In this case, cracking coincident with corrosion (schematic shown in Figure 1) provides the motivation for the current study."

Jan 1, 2012

By Yoginder P. Chugh

This paper discusses an ongoing field study in southern Illinois (USA) that focuses on: 1) Identifying mechanisms of instability in the set-up rooms (SR) and their T-junctions with headgate and tailgate entries, 2) Developing alternate 3-entry and 4-entry set-up rooms geometry using 3-D numerical analyses, 3) Implementing developed geometries in cooperation with mining professionals and regulatory agencies, and 4) Demonstrating performance of implemented geometries through field monitoring. Illinois longwall mining operations typically experience ground control problems (roof falls, rib sloughing, floor heave, etc.) within SR layouts and around the T-junctions of SR. These occur around the areas where the SR for adjacent longwall face (to be mined) connect with the SR of the previously mined face, and around the tail-gate entries of the mined-out longwall face and around the T-junctions of SR. The problems manifest as highly fractured immediate roof strata, major shear zones in the roof, horizontal displacements within the excavations that result in shearing off the heads of the bolts, floor heave and severe rib sloughing. Similar observations have also been made in longwall mining in Utah.

Aug 1, 2013

By M. Aushouri, S. H. Mansouri, N. Aminizadeh

A thermo-chemical model of the Peirce-Smith copper converter has been developed to predict the molten temperature. The primary assumption of the model was that all matte, slag and gaseous phases in the converter were in thermal and chemical equilibrium. In this model, the matte components were considered only as copper, iron and sulfur elements. In the slag making stage, all the reacted iron was converted to fayalite. The reaction rate of iron and oxygen in this stage was considered to be constant. The converter temperature was calculated by heat balance over time. The model was validated by a detailed comparison with measured industrial data. A good agreement was obtained. The converter temperature depends on process parameters such as oxygen efficiency and molten emissivity.

Jan 1, 2007

By V. Vakiloroaya

The paper aims at developing a hybrid solar-assisted air conditioner system for performance enhancement and energy efficiency improvement. To increase sub-cooling of the refrigerant at partial loads, we propose a new discharge bypass line together with an inline solenoid valve, installed after the compressor to regulate the mass flow rate of the refrigerant vapour passing through a hot water storage tank. For control design, a lumped parameter model is first developed to describe the dynamics of the system in an explicit form of input-output relationship. The system has been fully-instrumented to examine its performance under different operation conditions. The system model is then validated by extensive experimental tests. The predictions from the models exhibit a good coincidence with experimental results, judging by an RMS error less than 15%. Based on the obtained dynamic model, a linear quadratic regulator (LQR) is applied to optimize a cost function of the output errors and control efforts. The key challenge is to regulate the refrigerant temperature entering the condenser by controlling the valve opening. The design approach is then tested in a transient simulation tool to predict the system performance in transient conditions. The experimental results obtained from implementation with PLC demonstrate that the proposed system delivers higher system efficiency owing to the higher refrigeration effect in the direct expansion evaporator. Thus, the novel development is promising for improvement of energy efficiency, enhancement of the system performance while fulfilling the cooling demand. Consequently, between 25 and 43% of monthly electricity can be saved on average.

Aug 1, 2013

By H. -L. Heikkilä, E. Peuraniemi

"Boliden Harjavalta Oy has a long tradition in the Finnish metal industry starting from the 1930's. The Smelter consists of copper and nickel flash smelting lines. Off-gases are captured in the acid plant to produce sulfur products. During the early years of production, the surrounding environment suffered from high SO2 and dust emissions. The first acid plant started in 1947, a few years after commissioning of the smelter. The flash smelting method was developed and commissioned in 1949. This created the basis for today’s environmentally sound metal production. Recent air emission reductions are related to treating lean ventilation and granulation gases. Emissions from the stacks are monitored with continuous measurement devices. SO2 and PM10 concentrations are also measured from the residential area and reported online in cooperation with Harjavalta community and other local industry.INTRODUCTIONProductionBoliden Harjavalta Oy smelts copper and nickel concentrates and refines copper in the western part of Finland. The copper concentrates come from external copper mines mainly in South America and Europe. Concentrates are unloaded at the Pori harbor and transported to Harjavalta by train from a distance of about 60 km. Boliden Harjavalta Oy has operations in Harjavalta and Pori. The smelter in Harjavalta produces copper anodes that are transported via railway to the copper refinery in Pori. The anodes are electro-refined into copper cathodes and by-products like Se, Ag, Au and Pt/Pd concentrate. In the Harjavalta smelter SO2 containing gases are delivered to a sulphuric acid plant where sulphuric acid and liquid sulphur dioxide are produced.Our nickel smelter smelts nickel concentrates on a tolling basis to produce nickel matte for customer needs. SO2 containing off-gases are delivered to the sulphuric acid plant for sulphur capture and modification into products.All our operations are certified according to the Quality, Environmental and Occupational Health and Safety Standards ISO 9001, ISO 14001 and OHSAS 18001. Boliden Harjavalta Oy was the first company in Finland operating in the metal and technology industry to be certified according to the Energy Management Standard EN 16001, currently this certification is done according to ISO 50001."

Jan 1, 2012

By D. Royston

Reducing SAG Mill feed size has been a major trend in recent years. ?Mine to mill? strategies have reduced blasted-rock size, and in a growing number of operations reducing the primary crusher CSS and/or adding additional crushing upstream of the SAG mill have reduced rock feed size. While reducing feed size will increase SAG mill throughput, issues arise in terms of retaining charge in the mill, exposing the shell lining to impact damage, and maintaining milling performance should the pre-crush system shut down. This paper reviews the past experience on pre-crushing for SAG mills and provides an analysis of liner design (in particular grates and shell liners) for pre-crushed feed.

Jan 1, 2012

Mining Equipment Challenges Equipment Availability Unplanned downtime Maintenance Costs Secondary damage and catastrophic failures (T282 $750k) Emergency work is 4x the cost of planned work Inspections Troubleshooting time Incorrect repairs (parts, labor, lost production) Equipment Life Mis-operation of equipment

May 1, 2013

By M. Proulx

"RÉSUMÉ Le diagramme ternaire Al2O3-Sr-Y est un nouvel outil servant à l’exploration de gisements de sulfures massifs volcanogènes (SMV) archéens. Le diagramme permet de discriminer entre les roches volcaniques à minéralisations à zinc dominant (domaine Zn+) et celles à minéralisations à cuivre dominant (domaine Cu+), ainsi que les roches volcaniques ayant subi une chloritisation hydrothermale pouvant aboutir à la formation de chloritites associées aux cheminées d’altération (domaine Cl+). Ces trois domaines délimitent des zones d’influence géochimique ou d’empreintes hydrothermales résiduelles ou fossiles produites par les cellules de convection hydrothermales générées par des magmas. Le diagramme permet aux sociétés d’exploration de déterminer de façon peu coûteuse la fertilité potentielle des roches volcaniques archéennes en ayant recours à leurs bases de données et aux résultats de leurs analyses de terrain, sans aucune manipulation des données. Le diagramme ne s’applique pas aux SMV aurifères.ABSTRACT The tertiary diagram Al2O3-Sr-Y is a new tool to explore Archean volcanogenic massive sulphide (VMS) deposits. The diagram can be used to discriminate between the volcanic rocks where zinc is the dominant mineralization (Zn+ domain) and the rocks where copper is the dominant mineralization (Cu+ domain), as well as the volcanic rocks that were subjected to hydrothermal chloritization that could have led to the formation of chloritites associated with alteration chimneys (Cl+ domain). These three domains define the zones of geochemical influence, or residual or fossil hydrothermal footprints produced by hydrothermal convection cells generated by magmas. Exploration companies can apply the diagram to determine, at low cost, the potential fertility of the Archean volcanic rocks by using their databases and the results of their field analyses, without any data manipulation. The diagram does not apply to gold-bearing VMS deposits."

Jan 1, 2015

By Art Hamilton

Abstract -The Zn-Pb-Cu-Ag ore deposits of the Boundary and N-5 zones near Bathurst, New Brunswick, occur in a polydeformed volcano-sedimentary sequence that is part of the Ordovician Tetagouche Group. Massive and disseminated sulfides are hosted by an argillaceous to cherty sedimentary sequence that is stratigraphically underlain by a siliceous fragmental unit and is overlain by a feldspar-rich crystal tuff and related tuffaceous rocks. The deposits have a low iron sulfide con­ tent relative to that of most stratabound sulfide deposits of the Bathurst-Newcastle mining district. The ore is commonly associated with chlorite- and talc-rich sediments. The N-5 deposit is considered to be the fault-displaced extension of the Boundary deposit. The Boundary deposit is estimated to contain 891 000 t grading 3.310Jo Pb, 7.96% Zn, 0.32% Cu and 44 g/t Ag; the estimate for the N-5 zone is 330 000 t grading 3.24% Pb, 7.15% Zn, 0.33% Cu, and 37 g/t Ag. The ore is processed at 1000 tpd at the Heath Steele mill.

Jan 1, 1992

By J. B. Mawdsley

Introduction The writer was instructed to visit the Chibougamau region during the field season of 1927 and report on the mineral discoveries that had been made there since 1911. lt was deemed advisable to obtain detailed information regarding the rocks underlying the area in the vicinity of these recent discoveries. Accordingly an area 60 square miles in extent was mapped. The outcrops were studied along the water courses and along bush traverses spaced at half-mile intervals between these water courses. The completion of the rest of the summer's programme allowed only three weeks for this work. lt is from this small, mapped area, and this necessarily cursory survey, that the material for this paper was obtained. Location And Means Of Access The name Chibougamau district is applied loosely to an ill-defined area of about 1,000 square miles lying mostly north and west of Chibougamau lake in the Province of Quebec. The lake is approximately half way between lake St. John and James bay. It lies 150 miles north of the Canadian National railway and 40 miles south of Mistassini?lake.

Jan 1, 1928

By O`Donnell. P. J.

THE modern coal cutter is a highly developed, and to a certain extent a somewhat complicated, machine. The requisite power to cope with conditions as found must be generated by the motor with due regard to limitations in the matter of dimensions and weight. This imposes the necessity of relatively high speeds of rotation. Any factor external to the machine proper which tends to reduce the load on the motor and gearing is most important. Experience has proved that close attention to the question of cutter-chain details undoubtedly results, in practically every coal-cutting operation, in increased efficiency and reduction of power and maintenance costs. The chain is the unit of the coal cutter which most greatly affects the economical operation of the machine, and only by due consideration of conditions and by the proper selection of the right chain can best results be expected; also, intelligent care of the chain while in operation is essential if it is to give its best service. The chain is the part of the machine that carries the pick boxes or blocks, which are connected to each other by a pair of chain links. The power to drive the chain is trans-mitted by a sprocket. The chain runs in guides supported by a rigid member called a 'jib'. Figure 1 shows the various parts mentioned. The first requirement of a chain is that it cut the coal as fast as possible. The second is that it do so economically. Economy of cutting can conveniently be divided as follows: (1) Economy in power used. (2) Economy in pick life. (3) Economy ' in chain life. ( 4) Economy in jib life. (5) Economy in labour for maintenance.

Jan 1, 1936

By D. F. Kidd

Introduction In a companion article, Surveys at Great Bear Lake, 1931, R. C. McDonald has described the general character, topography, and climate of the Great Bear Lake-Coppermine River area and the main means of access (l). The present paper will largely be confined to the geological features of the district. In the last two years, the rocks of the region have received considerable attention, and papers including references to .the geological succession have been written by Knight(2), Duncan(3), Norris( 4), Reid(5), Cameron(6),and Kidd(7). The writer confined his field-work during the 1931 season to the district between LaBine point and Hunter bay and northwest to the head of McTavish arm. Brief trips were made down the Sloan river from McLaren lake, 25 miles northeast of Hunter bay, to that place, to Dowdell (Sixty-six) point, the south point of Echo bay, and to the region north of the Dismal lakes and west of the Coppermine river. The inner part of Echo bay, which is the area discussed by Reid and Cameron, has not been seen by the writer and the geology there will not be discussed.

Jan 1, 1932

By R. D. Mollison

"Ecstall Mining Limited was formed to operate the Kidd Creek mine, discovered by Texasgulf Incorporated in 1961 the orebody is geologically very complex, containing rich values of zinc, copper, silver and lead. The first phase of the operation involved an open pit, railroad and concentrator complex, which was under construction in 1965 and began operations in late 1966. The open pit, with rim dimensions of 2,000 by 1,000 feet, was computer-designed and highlights excellent wall control and efficient ore extraction and grade control. The railroad was built over the worst type of muskeg country, but it has been well maintained, resulting in an uninterrupted supply of ore in the trains. The 10,000-tpd concentrator, located 17 miles from the mine, is highly instrumented and automated. It features computer control of reagents and, in addition to the copper, zinc and lead flotation circuits, has a modern gravity tin plant. The concentrator is large, because very fine grinding is required for good metallurgy and nearly 2,500 tons per day of concentrates are produced. In 1969, work was started on the underground mine to take over from the open pit; it began partial production in mid-1973. The mine is highly instrumented, has a ramp from surface, a high-production shaft, an underground gyratory crusher and an efficient orehandling system, and employs the latest mining techniques. The electrolytic zine plant, rated at 120,000 tons of slab zinc per year, started operation in April, 1972, with batch leaching and purification circuits. It has been converted to continuous leaching and is now in the process of converting to continuous purification. Further modernization and automation will be carried out in the next few years. Five service departments support the five operating departments. These are maintenance, engineering and technical services, geology, administration and employee relations. How these ten departments function and work together using the most advanced technology to produce an efficient operation is the main theme of the Ecstall Story."

Jan 1, 1974

The primary (sulphide) resources at Aphrodite are refractory in nature, requiring an oxidation process stage to be introduced to facilitate extraction of the gold. The company is investigating the use of pressure oxidation (POX) as the oxidation method for processing of high grade gold bearing concentrate it plans to produce at Aphrodite. POX has been used extensively around the world for the past 30 years and continues to be the favoured option for a number of refractory gold plants currently in the design and construction stages. Initial pressure oxidisation testing investigated the effect of temperature, pressure and grind size on a bulk flotation concentrate prepared from Alpha lode material. The concentrate averaged 47.3 g/t gold and was prepared from a composite of core samples averaging 1.49 g/t gold. Sub-samples of the concentrate were subjected to POX for 1 hour resulting in rapid oxidation during this very short period. Testing undertaken showed that there was a significant increase in sulphide oxidisation at higher temperature (220°C) and pressure (2,500 k/Pa) for the two grind sizes (75 and 20 microns) evaluated. The proposed flowsheet, OPEX and CAPEX are critical aspects for project development.

Jan 1, 2014

By Martin Landwehr

"Dust samplers are based on different principles. The konimeter is based on the number of particles counted; mining applications are based on routine sampling; and the photometrical evaluation of samples is used after the pre-separation of particles above 5 micron by the mining konimeter. In special cases, the Draeger sampler is used for quantitative analysis. General trends are toward larger samples, concentration on a weight basis, fractionation into size groups by different techniques and an analysis of composition. Standards or TLVs already exist in all industries. Surface industries base their criteria on concentrations and quartz contents in particles below 5 micron. The mining industry uses the tyndalloscope routinely to determine concentrations; concurrent] y, the rock content, as deter-mined by ashing samples, is obtained by konimeter.Threshold limits are related to the rock content in respirable fractions and tyndallometrically determined concentrations. The TL Vs are based empirically on Landwehr's ""dust values,"" as agreed upon with the Mines Inspectorates. Recently, and in accurate sampling, dust samplers have been used that count the dust in two fractions -above and below 5 microns. Mineral composition is determined either for all minerais or just for quartz. In assessing the dust hazard by Landwehr's ""dust values,"" all minerais are taken into consideration; in coal dust sampling, however, only the quartz content is taken into account. Efforts are now being made to co-ordinate the different assessment methods, arriving at uniform MAC values in agreement with those of other countries."

Jan 1, 1969

By J. Chenier, M. Boissoneault, D. Ducharme, R. Schonewille

The operation of Falconbridge's Sudbury nickel smelter has undergone significant change since the production was consolidated to a single electric furnace in 1994. In the late 1990's a capital program of about $100 MM (Cdn) was undertaken to expand and modernize the smelter. This project, known as Smelter 2000, was mainly driven by the need to process the new concentrate produced at Falconbridge's Raglan operation in northern Quebec. Included in the scope of the project was the installation of dry concentrate handling facilities, modifications to the roaster feed preparation system, installation of a matte granulation system and modification of one of the converters. Improvements to in-plant hygiene were also an important part of the Smelter 2000 project. Over the past 5 years much has been learned about the challenges in treating two significantly different concentrates. More recently, the introduction of a third concentrate from Falconbridge's new Montcalm operation near Timmins, Ontario has added another dimension to the operation. This paper will describe how the main challenges from the past 7 years have been overcome and discuss the path forward for the Sudbury Smelter Business Unit.

Jan 1, 2005

By L. M. Pidgeon

Introduction The production of magnesium by direct reduction of the oxide has far passed the experimental stage and was responsible for 30 per cent of the recent wartime production of 246,000 tons per annum. This paper describes the small-scale experiments which culminated in a number of the wartime plants. The paper traces the author's early experiments on various direct reduction reactions leading to his choice of the ferrosilicon reduction of dolomite and the realization that this reaction would proceed at a satisfactory rate at temperatures obtainable in metal apparatus. MgO has a standard heat of formation of 146,100 cal. and is therefore one of the most difficult oxides to reduce. However, if advantage is taken of the relative volatility of magnesium metal, thermally unfavourable reactions may be utilized. In reaction MgO + X = XO+ Mg . . . . . . . . . . . . . (1) the removal of Mg as a gas at high temperatures displaces the equilibrium to the right in the face of the unfavourable thermo-chemistry which is inevitable with any X other than calcium metal. If X is carbon, not only is the reaction highly endothermic, but CO is gaseous. A temperature of l,864°C. is required to produce a pressure of one atmosphere of Mg. Between l,900°C. and perhaps 400°C., the back reaction takes place readily and special shock cooling devices are required to recover magnesium from the gaseous mixture. This reaction does not lend itself to small-scale experiments and was not examined by the author. If, in reaction, carbon is replaced by a relatively pan-volatile metal, the oxide of which is also non-volatile and possesses a fairly high heat of formation, a reduction reaction is offered which is free from the difficulties associated with carbon. The typical case of silicon will serve as an example: 2MgO + Si = SiO2 + 2Mg (g) . . . . . . . . . . . . . . . . . . . . . . (2) At temperatures above l,000°C., a positive pressure of magnesium will exist over the system. Removal of the magnesium vapour will displace the reaction to the right in the face .of an unfavourable thermal balance. Since magnesium is the only volatile component at this temperature, it may be evolved and condensed, using attractively simple distillation technique.

Jan 1, 1946

By P. Langlois, G. Labonté, J. J. Barrett, J. Holmes

"The Voisey’s Bay mill processes a high-grade pentlandite and chalcopyrite ore in a largely pyrrhotite/troilite matrix. From 1994 to 1997, circuit development focused on making a 14% nickel concentrate. When flowsheet development resumed in 2001, the target grade was raised to 20% ni. initially triethylene tetramine and sulfite pyrrhotite depressants were used in a lime circuit, but by recycling process water and the contained thiosalts, the required nickel grade was made without depressants. construction of the mill was fast-tracked, with start-up in september 2005. ramp-up was faster than other recent nickel installations, with tonnage being limited by concentrate dewatering due to higher-thanexpected ore grades.RÉSUMÉ l’usine de traitement de Voisey’s Bay traite un minerai à teneur élevée en pentlandite et chalcopyrite dans une matrice formée surtout de pyrrhotite/troïlite. De 1994 à 1997, le développement du circuit ciblait la production d’un concentré à 14 % de nickel. lorsque le développement du schéma de traitement a été repris en 2001, la teneur cible a été élevée à 20 % de ni. initialement les déprimants triéthylènetétramine et sulfite de la pyrrhotite étaient utilisés dans un circuit à la chaux; cependant, en recyclant l’eau du procédé et les sulfosels qui y sont contenus, la teneur en nickel a été atteinte sans utilisation de déprimants. la construction de l’usine de traitement a été accélérée et elle a démarré en septembre 2005. la mise en opération a été plus rapide que pour d’autres installations récentes de nickel; le tonnage traité étant limité par le séchage du concentré en raison des teneurs de minerai plus élevées que prévu.INTRODUCTIONnickel was discovered on canada’s east coast in the vicinity of Voisey’s Bay, northern labrador, by chislett and Verbiski (Higgins, 2011) while working for Diamond Fields resources in 1993. The ovoid deposit was subsequently delineated in the winter of 1994–1995. By the end of 1995, the ovoid had been well explored, and at that time was thought to have a reserve of at least 30 million tonnes (Mt), with an average grade of 2.83% ni and 2.0% cu (naldrett, singh, Krstic, & li, 2000). Drilling to the east of the ovoid indicated the presence of significant mineralization. in June 1995, inco limited bought a 25% share in the Voisey’s Bay nickel company (VBnc), which was a subsidiary holding company set up by Diamond Fields. inco also bought 8% of Diamond Fields and negotiated the right to sell all the nickel produced from VBnc for 20 years as part of this agreement. in april 1996, inco bought Diamond Fields and acquired the remaining 75% of VBnc shares."

Jan 1, 2017

By Robert J. Shank

This paper describes the Federal Government assistance available for northern mining development. The paper commences with a discussion of why the Federal Government should give assistance to northern mining development. It then uses a hypothetical case of a company which has a property it wants to develop to list the sectors within the . Federal Government that would have to be consulted in order to obtain federal financial assistance. The paper also outlines the type of information a company must be willing to provide the government in order to qualify for such assistance.

Jan 1, 1978