Search Documents

By F. W. Gray

IN 1922, the writer communicated to the Institute a paper entitled The Development of the Coal Industry in Canada (1), which summarized the considerations set out in a series of papers (2) concerned with coal-mining in Canada which he had presented in 1920 and 1921. This paper contained a forecast by decades, commencing 1920, of Canadian coal production, importation, consumption, and exports, based on anticipated rate of population increase, and continuation of the gradual increase in the per capita rate of coal consumption in Canada that had taken place every year up to 1920. The following comparative statement brings our the differences between the forecast and actual experience:

Jan 1, 1936

By Egon Berger

"In recent years the trend in underground metal mining has been toward ever increasing blasts (often in excess of 100 000 tonnes per blast). The Canadian mining industry has been in the forefront of these developments (VRM, LBHand cable bolting to stabilize the surrounding rock /avoid dilution).In order to move these large tonnages, efficient loading systems have to be developed. This paper shows the technical and economic implications of various loading scenarios based on a predefined (however typical) stoping layout by:1 . discontinuous loading using scoop trams;2. discontinuous loading using scoop trams in combination with low profile dump trucks;3. continuous loading (based on loading performance/operating costs of the AL-60) in combination with low profile dumptrucks.The cost advantages of production concentration (loading large tonnages from one drawpoint}, made possible by continuous loading as opposed to sea tiered mining (small tonnages), using discontinuous loading in tunnelling will be presented, based on actual results obtained in a decline development project using the A L-60 continuous loader. At as pacing oj150m between turning bays, it was found that continuous loading was out performing discontinuous loading in approximately80% of the overall decline development.Fuel consumption and total cycle times are compared, and a cost assessment is presented.INTRODUCTIONThe subject of this paper deals with the introduction of continuous loading in underground metal mining and single heading tunnelingContinous mining has been widely introduced both in underground and surface coal mining. Mechanized longwall mining, utilizing moveable shield supports in combination with double drum- shearers, has resulted in a tremendous increase of coal production per working face.This has led to very concentrated mining operations. In a typical German coal mine two mechanized longwalls nowadays would produce the same amount of coal as 12 to 15 longwalls in the 1950s. One longwall in a South African coal mine has recently set a world record with 120 000 tonnes of coal in a single month.In underground metal mines-often due to the irregular nature of the ore body and the mining methods used-mining is far less concent rated. Ore is often produced from a large number of stopes and production sections. Sometimes, a substantial amount of ore may be obtained from development in the orebody (40070 at a German base metal mine)."

Jan 1, 1989

By D. D. Hogarth

"IntroductionThe Hull iron range, comprising the Forsyth, Scott , Baldwin and Lawless properties (Fig. I), is in Gatineau Park, on the outskirt s o f the city of Hull , and about 6 miles (10 kilometres) northwest of the Federal Parliament Buildings.The deposits have been known many years and described numerous times, although the history has been treated lightly in former publications. Total ore shipments have been calculated at 122,700 long tons, of which over 80% were mined before 1900 and 74% in two brief periods: 1870-74 and 1880-82. It is surprising that the period 1870-74 has been overlooked by most authors and 1880-82 ignored altogether. More surprising, the essential data for these two periods are contained in manuscripts of the Robert Bell collection, which must have been available to officers of the Geological Survey o f Canada.The period 1801-1874 ha s already been covered by the writer in ""Pioneer mines”, but much information has come to light since publication. The present paper is therefore based o n new data and a fresh appraisal. However, little additional data were found for the early history (1801-1854) or for the legal cases involving A.H. Baldwin, and these parts were mainly summarized from the relevant sections of the above-mentioned publication.GeologyThe ore deposits are all situated somewhat below the middle of a graphitic, calcitic marble horizon, here folded into a northeast-plunging synform. The Forsyth, Scott and Baldwin deposits are on the south limb of the synform; the Lawless is on the north limb. The marble is underlain by three non-carbonate groups: biotite gneiss with interlayered quartzite (top), granite gneiss and skarn (middle), and biotite-garnet gneiss (bottom). Below these groups is a lower horizon of graphitic, calcitic marble. The whole sequence is Precambrian and has been subjected to high-grade (Grenvillian) metamorphism, but, in the north, is cut by an unmetamorphosed Cambro-Ordovician diabase dyke. For further information, the reader is referred to the summary by Baird."

Jan 1, 1983

By R. Khanna, I. Mansuri, S. Devasahayam

"Recycling polymer based end-of-life materials as carbon resources for a partial replacement of coke/coal can make important contributions towards enhancing the environmental sustainability of steelmaking processes. An in-depth high temperature (1550°C) investigation has been carried on waste CDs/DVDs focussed specifically on char generation, characterization and dissolution into molten iron. The simultaneous presence of carbon and oxygen in polymeric chains on polycarbonate substrates resulted in the generation of a significant pore structure and exposed surfaces. Carbon dissolution studies into molten iron were carried out on the raw polymer as well on chars; high levels of carbon pick-up were observed in both cases after 15 minutes of contact at high temperatures. INTRODUCTIONOver the past sixty years, plastics have played an important part of our daily lives and are being increasingly used in all aspects of the global economy. More than 260 million tons of plastics are produced annually worldwide. Their rapid growth and extensive utilization with a short life span (such as packaging) has created a massive waste problem. Although the waste plastic component in municipal solid waste (MSW) amounts to only about 10 %, plastics have a high volume-to-weight ratio and these are generally not biodegradable. In Australia, ~19.20 % of plastics were recycled in 2009-2010 (PACIA, 2010); with the total consumption being estimated at 1,501,258 tonnes, 288,194 tonnes of plastics were recycled. There are serious environmental concerns with the two key waste management options, i.e. land filling and incineration, and there exists an urgent need for developing alternative recycling approaches. In this paper, we focus our attention on recycling waste CDs/DVDs polycarbonate substrates as a carbon resource in steelmaking.CDs/DVDs used for music/data/image are made from aromatic polycarbonate resin (hereafter abbreviated PC). This resin is also widely used as an engineering plastic in applications such as automobiles, mobile phones, notebook type personal computers, cameras & video cameras, electric & electronic appliances, fire equipment, life & living goods, roofing sheets, etc. High consumption and growth (~10% annually) of PC utilization is attributed to its excellent properties such as outstanding impact resistance, transparency, heat resistance, and dimensional stability. The molecular formula and composition of PC resin is given below:"

Jan 1, 2012

By K. Hasselwander, K. Knabel

"A significant area of Outotec’s business involves fluidized bed roasting. With several decades of experience, more than 300 reference plants and strong R&D capabilities, the company provides several industries with optimum processing solutions. Applications include oxidation and sulfation of sulfides found in copper, pyrite and zinc concentrates. Gold production and de-arsenifying roasting are also within this scope. This paper describes the latest furnace developments and includes novel trends. Moreover, hot and wet gas cleaning systems are examined focusing on unit operations related to the removal of components such as dust, SO2 for sulfuric acid production, fumes, halides, Hg, hydrocarbons, nitrous oxides and metals.INTRODUCTIONGenerally, when defining roasting processes, it can be stated that the respective primary pyrometallurgical reaction is exothermic, of gas-solid nature and relates to a value solid product. These processes are a key focus within Outotec’s scope and include: (i) dead roasting (ii) sulfating roasting (iii) partial de-arsenifying roasting and (iv) two-stage, de-arsenifying roasting.Dead roasting involves the oxidation of a given sulfide, thus allowing for a subsequent leaching process, and has been applied to producing ZnO. Dead roasting of pyrite has also been extensively utilized with a primary goal of producing sulfuric acid. In contrast, sulfating roasting involves converting a sulfide to its sulfate, enabling a selective sulfation of components, such as Cu or Co, and their separation from ferrous components during leaching (produced sulfates are soluble). Partial roasting involves partially oxidating the metal sulfide to its oxide with the simultaneous production of gaseous As4O6, which is handled during gas cleaning. The solid product, containing hardly any As, is rich in S and can be fed to a respective smelter (e.g. in the case of Cu). Alternatively, if the production of oxide is required, a dead roasting step is added after the partial roasting step, with the overall process considered as two-stage roasting."

Jan 1, 2012

By Wynne Potter

"On the west coast of Cape Breton Island four coal basins have been identified, varying in age and extending from Port Hood northeasterly to Chimney Corner. Those of Chimney Corner - St. Rose in the north and Port Hood in the south belong to the Pennsylvanian Riversdale Group while lying between them are the coal basins of Mabou and Inverness belonging to the younger Pictou Group. Almost all of the coal basins are submarine and coal mining was carried out on all basins at various times. The seams in all basins dip steeply seaward at angles from 10 to 20 degrees but were found to flatten seaward. The coal is ranked as a high volatile C bituminous coal. Ash and sulphur contents are high compared with Sydney coal and the coal has a tendency to spontaneous combustion when stored in large quantities.Of the four basins, the most significant is that of Mabou. At Mabou recent seismic and drilling investigations have indicated that although a sizable reserve of coal may be found offshore the structural problems, particularly faults, and the poor quality of the coal encountered will make it a resource of the future, if at all. Inferred resources have been calculated at 150 million tonnes in four seams over a 10 km2 area and extending 3 km from shore. The quality of the Mabou coals varies with ash, ranging from 5 to 25 per cent and sulphur up to 6 per cent. Calorific value ranges from 25.3 Mj I kg to 31. 7 Mj I kg. The Port Hood and St. Rose -Chimney Corner fields (Fig. 1) contain 16 million and 3 million tonnes respectively, but the Inverness basin is considered to have been depleted. The active mine in this area is the Evans Mine at St. Rose that is currently producing between 30 -50,000 tonnes a year from proven reserves of approximately 3 million tonnes."

Jan 1, 1985

By C. T. Dzgoev, S. S. Gudkov, IRGIREDMET JSC, S. G. Schtoick, A. V. Yepiforov, S. V. Balikov, I. I. Yevtuschevich

The pressure oxidation (POX) and pyrometallurgical process comprises POX of gold containing sulfide and polymetallic lead-zinc concentrates prior to reduction smelting of POX products to generate a lead-silver-gold alloy. Refined lead and gold-silver alloys are then obtained using conventional processes. Zinc and other base metals are recovered from the POX solution. In the course of POX, zinc dissolves in the solution and lead concentrates in a solid residue in the form of sulfate compounds. Sulfur forms the major iron sulfates and jarosites. In order to dissolve sulfur and arsenic from solid residues to the solution, the slurry hot curing was carried out at the temperature of 95°C within 2 hours. After filtration of the slurry, zinc was recovered from the solution. The resulting cake was washed with water and subjected to hot alkaline treatment. After alkaline treatment, the cakes were blended with fluxes and subjected to reduction smelting to generate lead concentrate containing precious metals. This concentrate was refined to obtain refined lead and gold-silver alloy. After iron and arsenic were removed from POX solutions using sodium carbonate, zinc was precipitated as carbonate. After thickening and filtration, zinc precipitate was roasted to generate saleable zinc oxide. Using this process, the recoveries of values to saleable products were 97% Au and 95% Ag to the alloy, respectively, 91% Pb to refined lead and 5% Pb to lead and antimony alloy and 94% Zn to zinc concentrate. The features of the technology is that it has high recovery indices of precious and base metals to saleable products and can be used to process various polymetallic ore and technogenic raw materials.

Jan 1, 2016

By H. G. Stephenson, C. W. Gregory

"This article describes the methods used for pillar extraction in the Wilson Seam at Canmore Mines, Alberta. The Wilson Seam is extremely gassy and varies in thickness between 7 and 30 ft, with an average of 12 ft. The gradient varies from 5 to 30 degrees, with an average of 15 degrees. The seam was developed using Lee Norse miners to form pillars which the company intended to extract using the same machines. Before pillar extraction commenced, an abandoned and inaccessible mine 160 ft above the Wilson had to be drained of 360 million gallons of water. When this was done pillar extraction commenced. Conditions in the mine slowly deteriorated and after 6 months the decision to withdraw the continuous miners was taken. Slusher hoists were installed to replace the continuous miners, with the result that roof conditions and safety steadily improved."

Jan 1, 1972

By B. H. Sadagah

"Construction of mountain roads at north westerly Saudi Arabia is a difficult task in rugged terrains, where the rock masses are steep slopes, and full of geomorphological constraints.Werka descent lies at the north west region of Saudi Arabia. The Werka descent, constructed four years ago harmed due to rainstorm. The rock masses are metabasalt and metaryolite tuff rocks. The road is eight m-wide, surround by unsupported sharp manmade slope cuts, reaches up to 15 to 40 m height on both sides. Failures took place at both sides of the road, and blocked it. The road of almost 2 km long subjected to all modes of slope instability such as rockfalls, manmade slope failures and debris flows in the absence of the remedial measures. The very precipitous 40 m-high rock slope-cut along the road has no benches, backed by a natural slope of almost 80 m height. Both types of slopes suffer from rockfalls and slope failure’s incidents, frequently took place mainly in rainy seasons. The steep manmade rock slope cut is less than 1 m close to the road, with no ditches, form a potentially source area for rockfall’s hazards.Intensive geotechnical study includes utilization of the RMR and GSI rock masses classifications indicates that the rocks are fair to poor quality. The DIPS, RocFall, Swedge, RocTopple, RocPlane computer program, in addition to GIS and DEM image utilized to perform modeling and deterministic analysis, in order to suggest the mitigation measures for the natural and manmade slope cuts and rockfalls. The seismic coefficients of 0.1 to 0.4 taken into consideration in modeling processes. Input parameters to model the rockfalls and slope failure’s characteristics were studied such as GSI, block size; seeder points, locations of fallen blocks; slope angle, restitution coefficients, and slope roughness. The programs modeled the proposed location, height and energy of the rockfall barriers, collectors, and rock bolts. Two manmade slope cuts studied and modeled utilizing the integrated techniques were to eliminate the risk of slope failures and rockfalls through the construction of remedial measures, this is the study objectives."

Jan 1, 2015

By C. Mawdsley

The Tata Steel mill at Skinningrove in the North East of England produces top hat sections for mineshaft guides in sizes 102 and 150 mm. The top hat section is the technically preferred shaft guide choice for modern deep mine shafts. This paper explores the relative service performance of top hat and square hollow section guides in service. Comparative corrosion performance is reviewed and the paper describes work commissioned by Tata Steel (as Corus) undertaken by Aker Kvaerner Engineering to evaluate relative winding speeds, relative loads and fatigue life in service. The experience of supply to UK Potash mining is discussed and the future view of high capacity hoisting and larger section size market need and availability is assessed.

Aug 1, 2013

By L. Bos

The availability and reliability of large grinding mills and their Gearless Mill Drives (GMDs) are of paramount importance for the grinding process. Although GMDs have been in service for decades, and are known for their operational efficiency (reliability and robustness with reduced operating cost per ton), compared to conventional drives, in the last decade due to certain reasons some failures led to serious unscheduled shutdowns and significant insurance events. The majority of these notable "insured" failures have happened on GMDs installed on relatively large mills, as the financial impact of a failure is proportional to the through-put of the mill. Despite the occurrences of these events, as mining operations are driven by lower ore grades and the ability to continue reducing operating costs per ton, the trend for having larger mills is still very present and there is no reason why this trend should not continue. It is obvious that if not handled correctly, the possibility of large value GMD loss events, coupled with the continuing increase in mill size or required availability and reliability targets, could potentially lead to major conflicts as it becomes difficult for the insurance companies to judge the risk and hence may result in hesitation to insure these grinding circuits. This paper will not only describe the conflicting situation from both an insurer's perspective and from an equipment supplier's perspective, but also how these conflicting challenges can be successfully mastered. It has to be noted that not only the mining companies themselves, but also their insurance companies and the involved equipment suppliers have a common interest: to reach the highest availability and reliability in order to avoid or at least minimize unscheduled shut down times, and most importantly prevent unplanned events that result in extended production stoppages or reductions in through-put of GMD driven mills. From the very beginning onwards, the complete service concept together with emergency plans must be integrated on every level in the design of the grinding circuit. This approach must be implemented continuously and without compromises by all involved parties during all following stages, such as basic design, detail design, manufacturing, quality inspection and testing, packing, transportation, storage, installation, commissioning, operation and maintenance. The concept of formal risk analysis related to mill operations, maintenance and spare parts strategies must be an integral part of mining companies? decisions related to the selection for installation and continued use of large mills powered by GMDs. The service concept in place for operating mills shall also have a clear focus on very early detection of any abnormalities, so that the risk can be mitigated and unscheduled shutdown times avoided. However, if a major failure occurs, then procedures and tools shall already be available in order to ensure that production impact is minimized.

Jan 1, 2012

By J. C. Gathje

Newmont&apos;s Phoenix Project is located near Battle Mountain, Nevada and is scheduled to produce copper concentrates containing high precious metal values. High temperature pressure oxidation (PDX) of the concentrates was considered as a treatment option during process development. The metals content in Phoenix concentrates range from: 15-25% for Cu, 1-10% for Zn, 0-2% for Pb and ?27% Fe. The precious metals content of the Phoenix concentrates can range up to ?300 g/t Au and >3,000 g/t Ag. As a consequence it was necessary that any process for consideration should have the capability of recovering both the copper and precious metal values. Typically, gold can easily be leached from the autoclave discharge solids, but silver is chemically bound with the jarosite formed and cannot be directly leached. Laboratory investigations led to the development of a patented PDX process that minimizes the formation of jarosite so that the silver can be leached easily along with the gold. The process was confirmed with extensive pilot plant testing. Excellent solution extraction of copper and zinc was achieved, and both iron and lead were precipitated in the PDX residue. The process produces clean PDX discharge liquors with very low iron concentrations. As an example, conventional PDX techniques resulted in pregnant liquors containing ?5 g/L Fe. However, the Newmont process, which controls the iron and sulfate species, achieved high iron precipitation in the PDX solids and pregnant liquors containing <0.5 g/L Fe. High gold and silver recoveries were achieved by direct cyanidation of the PDX solids. This process has the added benefit of producing PDX solids that demonstrate superior settling and filtration characteristics.

Jan 1, 2006

By C. H. Lau, I. T. Ng

Uniaxial Compressive Strength (UCS) of rocks is an important mechanical parameter for many civil engineering and rock engineering applications such as tunnel excavation, slope stability and foundation design. Macau is one of the world's fastest growing and most densely populated cities, many large and important infrastructures have been being continuously built using pile foundations which are designed to be supported by granitic bedrock. In Macau, the UCS of the granitic bedrock is required almost for every project involving pile foundations and is always measured directly from UCS test in the laboratory. However, direct measurement of UCS requires high quality rock core sample which is not only time-consuming and expensive but also requires high level of operating skill. In view of this fact, estimation of UCS using some empirical correlations will be more practical and efficient because they are relatively fast and economical compared to the direct measurement from UCS test. In the past, some empirical correlations had been established and widely used for estimating UCS of rocks in common engineering practice. However, it has been well recognized that the rock properties are generally varied with sites or geological regions in other words an empirical correlation developed from one region or one country may not be applicable for other regions or countries. Due to the reason that the empirical correlations for predicting UCS for granite are scarce in practice, in this study an extensive experimental program has been performed and a large database containing data such as UCS, Point Load Index (Is50), Schmidt Rebound Hardness (RL), porosity (?), water absorption (S), specific gravity (Gs) and dry density (?d) has been developed. An attempt has been made for developing a new empirical correlation for estimating the UCS of Macau granite. Accordingly, a comprehensive statistical analysis for correlating UCS with Is50, RL, ?, S, Gs and ?d has been performed and a local empirical relationship based on the developed database is proposed for obtaining reliable estimation of UCS for the granite of Macau. Finally, the performance of the proposed correlation is accessed by using another independent testing database developed in this study. It indicates that Is50, RL, ? and S have strong correlation with UCS whereas Gs, ?d have poor correlation with UCS. This study not only proposed a proper predictive empirical correlation for UCS determination for Macau granite but also provides detailed statistical information which is beneficial to engineers for obtaining better characterization of Macau granite.

Jan 1, 2015

By J. J. Emery

There is an increasing awareness on an international level of the potential for utilizing many wastes and by-products as construction materials. This has resulted in recent major reviews by OECD and RILEM to supplement national activities by agencies such as CANMET, USBM, BRE and LCPC. Much of this international and national work was reported during an International Conference on the use of by-products and wastes in civil engineering held in November 1978 in Paris. Based on participation in the OECD and RILEM reviews, and the Paris conference, developments in waste and byproduct utilization of particular concern to Canada are described. The major technical and economic constraints involved are also reviewed, so that the over-all evaluation reflects important factors such as inherent variability and transport logistics. Areas requiring further research and development are also identified. Particular emphasis is placed on slags, salvaged asphaltic concrete and surplus sulphur. "Due to the rapid development of China&apos;s industry, more than a hundred million tons of industrial wastes are generated annually, which occupy lots of land for storing, bring about environmental pollution, obstruct industrial and agricultural production and cause harm to people &apos;s living. Therefore we must utilize them effectively to create wealth for our country. "

Jan 1, 1979

By G. W. MacLeod

The iron ore question in this country has been widely discussed for many years, but only recently has its real significance becoming generally understood. The exhaustion of the old Helen mine, in 1918, marked the last phase of hematite production in Ontario, and with the closing of the Magpie mine in 1921 , Canada ceased to be a producer of iron ore. For the past three years every ton of ore used in Canadian blast furnaces has been imported. In a recent issue of the Engineering and Mining Journal-Press, Arthur B. Pearsons, Assistant Editor, makes the following statement : Iron dominates the world. Some contend that coal is more vital. be-cause heat is needed to make iron and steel. But there are other sources of energy, more convenient and less costly and it is only a question of time when progress in hydro-electric development will have reached the point where coal will be but an incidental source of power and heat. Even more direct means than the generation of electricity by hydro-power eventu-ally will be developed by making available the latent energy of the sun. But iron; Science gives not the vaguest suggestion that anything will dis-place iron and steel as the most essential material tool of modem civiliza-tion. ? Hardness, tenacity, malleability-it possesses all these in unique de-gree. These are some of the qualities that make steel and iron indispensable in modern industry. The domestic consumption per inhabitant of the United States has climbed uniformly from 0.18 tons in 1900, to 0.36 tons in 1922. New kinds of machines and new types of structures are being devised every year; and steel or iron is the basis of most of them." It is unlikely that the Ontario Government were actuated by this motive when they appointed the Iron Ore Committee to investigate and report on the iron ore situation, nevertheless, these facts must have influenced them in some degree.

Jan 1, 1924

By A. Himsley, E. Byleveld

"With reference to the chemical constraints underlying the ion exchange process for uranium recovery, a generalized view is presented on the actual and the achievable efficiency of the process. The area considered is restricted to acid leach circuits in combination with nitrate, chloride or sulphuric acid elution.A comparison between actual plant results and the chemical requirements shows that:(a) Unless new and better ion exchange resins are developed, no dramatic change in equipment size and resin inventory is""anticipated. (b) Elution efficiency, especially for sulphuric acid, may be improved considerably. More concentrated eluates may beproduced at lower chemical consumption. A possibility of achieving additional purification solely by ion exchange is discussed.IntroductionThis paper presents a generalized view of the actual and the achievable efficiency of the ion exchange processes for urannium recovery. The study is restricted to acid leach circuits in combination with nitrate, chloride or sulphuric acid elution. The ultimate efficiency attainable with ion exchange is dietacted by the chemical reactions underlying the process. The most sophisticated technology cannot change the diffusion rates in the ion exchange resin nor make the uranium loading exceed its equilibrium valueThe design of an ion exchange plant for uranium recovery involves a considerable number of parameters as a result of the wide variety of pregnant solutions produced from different orebodies. Therefore, a generalized approach of the ion exchange process inevitably neglects some parameters which maylead to significant variations in apparently identical situations.The uranium concentration in the pregnant solution, together with its pH, are the principal variables which determine resin loading and residence rime in the ion exchange system. On the elution side, the type of eluant and its concentration will determine the contact time required and the amount of eluant needed to strip the resin. The temperature, the properties of the ion exchange resin, the total dissolved solids in the feed solution and the competing ions are other variables that affect the chemical performance; these, however, may be considered as a correction of the principal parameters if one is interested only in general trends."

Jan 1, 1980

By D. C. Carter, J. P. Anderle

"Exploration drilling of evaporite sequences in eastern Canada has undergone significant changes in equipment, techniques and philosophy since the early 1970s. The result has been the recovery of full-size cores from properly conditioned and stabilized holes, high quality open hole geophysical logs, and high quality metallurgical samples. The majority of modifications have resulted from the necessity to preserve the integrity of the evaporite deposit, and thus ensure the potential development, combined with the need for cost-effective high quality information. This is particularly evident in the priority placed on the development of non-erosive drilling fluids, casing and cementing procedures. The results are applicable to diamond drilling exploration of evaporite deposits anywhere in the world.IntroductionThe majority of current technical and scientific literature and expertise available on such subjects as drilling fluids or cementing procedures is applicable to large diameter, deep (several thousand metres) oil-field type drilling . The differences between oil-field drilling and wire-line core diamond-drilling are dramatic: large diameter, deep holes drilled with a low rpm tricone bit using large volumes of fluid pumped through a large annulus versus small diameter, shallow (less than 600 m) holes drilled with a high rpm diamond-set core bit using small volumes of fluid pumped through a small annulus. Exploration drilling of evaporite sequences in eastern Canada in the early I970s was conducted using oil-field equipment and techniques to complete holes of moderate (1000 m to 1500 m) depth . The prohibitive cost of these operations has necessitated that subsequent exploration drilling employs modified diamond-drilling equipment and techniques developed as part of a transition away from oilfield methodology. The result has been full size core, recovery approaching 1000/0 and the ability to run open hole geophysical logs; a combination of factors enhancing the collection of high quality information (Carter, I989a)."

Jan 1, 1990

Accurate hematite solubility data are required to construct predictive solution chemistry models for complex hydrometallurgical solutions. These data are useful in understanding Fe(III) speciation and precipitation in a variety of hydrometallurgical processes. Hematite solubility data were generated in 10 to 70 g/L H2SO4 solutions and at temperatures from 130 to 270°C, using specially modified titanium autoclaves. These measurements represent an improvement over previous experimental data because of better in-situ filtration of the sample aliquots, the approach to equilibrium via hematite dissolution, and the inhibition of Fe(III) reduction on titanium surfaces. Fe(III) reduction was particularly studied to evaluate the inflationary effect of Fe(II) on hematite solubility measurements. Chromate was found to reliably inhibit Fe(III) reduction on titanium. Finally, the generated hematite solubility data were used to construct a solution chemistry model using the OLI software.

Jan 1, 2006

By P. Karimi, G. Mollataheri, A. Amini, H. Abdollahi, A. Mirzaeian

"Chah-Palang tungsten deposit is one of the two tungsten indexes in Iran. Based on ore characterization techniques (including optical mineralogy and XRD analysis), quartz, chlorite, atacamite, azurite, malachite, ferberite, illite, goethite and calcite were distinguished as major minerals. The representative sample was analyzed qualitatively by using X-ray fluorescence and chemical assay. Results showed that grade of tungsten oxide and copper were 1.76 and 7%, respectively. Also precious metals such as gold with grade of 1 ppm was reported in the sample. By using the mineralogical studies on the prepared sample, the liberation degree of tungsten minerals in –0.6 mm size fraction was obtained 80%. Several tabling tests were carried out on the original sample which at the optimum conditions and as a result, the grade and recovery of tungsten in concentrate reached to proximately 23 and 59%, respectively. To increase the grade of tungsten in the final concentrate, acidic leaching were performed on the tabling concentrate and its appropriate results indicated that the grade of tungsten increased to 27%. Also more than 90% of copper was extracted as a byproduct in the fallowed process.INTRODUCTIONTungsten, a unique hard, heavy heat-resistant metal, is distributed erratically in economic concentrations throughout most continents, occurring mostly as small irregular deposits that are not readily adaptable to large-scale, low-cost mining methods. The diverse physical characteristics and mineral composition of tungsten ores also present problems in beneficiation, requiring complex hydro- and pyrometallurgical treatment to yield high-purity concentrates suitable for the production of ferro alloys, carbides and super alloys in the steel industry (Hausen, 1989; Kholmogorov & Kononova, 2005). Tungsten is most frequently used as tungsten monocarbide, which has hardness close to diamond, in cemented carbides. The most well-known use of tungsten is in lighting filaments, and other important applications include improving steel properties and use in tungsten alloys, electronics, and chemical products (Hausen, 1989; Kholmogorov & Kononova, 2005)."

Jan 1, 2016

By P. G. Claridge, G. P. Holmes, M. A. Redfearn

"IntroductionThe purpose of this chapter is to describe current practices in operation and maintenance of flotation circuits in Canadian mineral processing plants. The chapter consists of five sections covering description of equipment, typical flow diagrams, operating practice, instrumentation and maintenance. The approach to this subject matter is intended to be practical in nature, hence no deeply technical treatment of flotation theory will be included.Flotation is an extremely common method of beneficiation of ores. Reasons are the relatively low cost of flotation compared to many other processes, the wide range of minerals to which flotation may be applied and the high efficiency of separation which can usually be achieved. The flotation process as we know it today has been developed within this century and it has had a major impact on the mining industry. While flotation is commonly considered to be important because it provides a relatively simple method of separating minerals in complex ores, the availability of flotation has also made a multitude of mineral deposits in Canada into economically viable mining operations because it allowed production of a concentrate of valuable minerals from the ore. These concentrates could then be transported from geographically remote locations to centraHzed plants for further processing, although the existence of the remote and perhaps small ore body alone would not have justified installation of metallurgical processing plants on site and the grade of ore would not have justified direct shipment of ore.Some of the more common minerals concentrated by flotation are sulphides of copper, nickel, cobalt, iron, zinc, molybdenum, lead and arsenic, as well as non-sulphides such as sodium chloride, potassium chloride, phosphates, silicates, chromite, fluorite, limestone and coal. Precious metals are also recovered by flotation, generally in association with another sulphide mineral."

Jan 1, 1989