Search Documents

By B. A. Zaharov, J. M. Shneerson, L. V. Chugaev, M. T. Zhunusov, A. M. Markelov, S. V. Drozdov

The main direction of research was the application of autoclave technology for the flotation concentrates or biooxidation feedstocks. The industry modernization also expects the possibility of increasing the yield of the flotation concentrate, to allow an increase in gold extraction in flotation circuit. This paper provides brief description of results obtained for concentrates with the yield of 4 and 8%, as well as corresponding biooxidation feedstocks. Technological efficiency of autoclave oxidation is shown for both concentrates and biooxidation feedstocks. The process has been evaluated on a laboratory and a continuous pilot plant scale. Gold extractions from POX discharge are ranging from 94-97% for each product, with only 5-7 kg/t cyanide consumed.

Jan 1, 2014

By Ahmad Ghahreman, Denver Cowan, Yeonuk Choi

"Testwork was conducted in order to compare the effectiveness of carbon based catalysts while oxidizing a gold-bearing pyrite concentrate under atmospheric conditions. Without the use of a catalyst the oxidation of pyrite was incomplete after 96 hours, resulting in roughly 60% pyrite oxidation. Furthermore the resulting sulphate yield from unassisted pyrite oxidation ranged between 72 and 84%. It is evident that atmospheric oxidation of pyrite is not viable due to slow oxidation kinetics and high sulphuric acid production when using a ferric sulphate media without a catalyst. The effect of two different carbon based catalysts, one Lewatit® AF 5 a new microporous carbonaceous bead, and the second a granular coconut shell based activated carbon, were tested under the same oxidation conditions as the unassisted pyrite tests. After 96 hours, Lewatit® AF 5 assisted oxidation showed approximately 96% pyrite oxidation with a sulphate yield ranging between 26 and 35%, while the activated carbon assisted oxidation reached approximately 100% pyrite oxidation with a sulphate yield between 36 and 37%. Testwork indicated that not only does the addition of a carbon based catalyst greatly improve the oxidation kinetics and lead to almost complete oxidation, the sulphate yield is also drastically reduced, resulting in very high elemental sulphur yields.INTRODUCTION Pyrite is an important sulphide mineral due to its ability to contain invisible gold concentrations up to 132 g/t (Chryssoulis & Cabri, 1990). As a result, ores composed of only a small amount of pyrite still have the ability to contain high gold grades. This refractory gold cannot be accessed via conventional gold leaching processes, such as cyanidation, and additional oxidative pre-treatment is required to liberate the gold, making it more amenable to extraction (Marsden & House, 2006). Current oxidative pre-treatments do exist consisting of both pyrometallurgical and hydrometallurgical processes including high temperature and high pressure leaching within autoclaves, biological atmospheric leaching and roasting. Autoclaves are a proven process reaching desirable recoveries within approximately a 1–2 hour retention time, due to the increased temperatures and pressures, allowing for an increase in dissolved oxygen (Marsden & House, 2006). The typical reaction for pyrite oxidation within autoclaves is presented in Equations 1, 2 and 3."

Jan 1, 2017

By George W. Bain

Summary During the last three years the discovery of gold in the belt of volcanic and sedimentary rocks extending eastward from the Porcupine and Kirkland Lake gold-fields has caused a great deal of excitement in mining circles. The area is heavily drift covered, and every aid to the location of veins is eagerly grasped. A knowledge of the physiographic history of the area is of the utmost importance in the application of many of these aids. Evidence is presented to show that glacial erosion has lowered the general elevation very little below the pre-glacial level, and that many glacial erratics have been carried less than three miles southward. Probably a knowledge of the general geology of a: region was never more necessary to the understanding of the distribution and continuation in depth of the mineral veins than in this area. Four distinct granites occur in the region, and gold-bearing veins are genetically associated with only one of these. Two types of quartz-feldspar porphyries have been found, only one of which has any bearing on the locus of the mineral veins. Many other examples of this complexity of associations might be cited, but everyone goes to show that in most cases the economic importance of the deposits can be realized only after the regional geology is understood. A series of sandstone, limestone and shale intruded by granite lies unconformably below the Keewatin lavas. The latter are intruded by a gneissoid granite and are overlain unconformably by the thick series of Timiskaming greywackes and silts. These are intruded by carbonated syenites and syenite porphyries which have since been rendered somewhat schistose.

Jan 1, 1927

By A. Gronningsater

Introduction As is well known, the fight between the blast furnace and the reverberatory furnace in copper smelting during the second decade of the century ended with a victory for the latter, a result which must largely be attributed to the introduction of flotation methods. To my knowledge, no new blast furnace has been blown-in at any American copper smelter since the War. As the metallurgy of nickel, up to and including matte smelting, is generally considered a close parallel to that of copper, the introduction of reverberatory smelting in the big new smelter of the International Nickel Company at Copper Cliff, built in 1928-30, seemed a logical adherence to a well established trend. In view of these facts, considerable comment was made when Falconbridge Nickel Mines decided to retain the blast furnace in their smelter built about the same time, in 1929. A presentation of the reasons governing this choice should therefore be of interest. The basic principles underlying the Falconbridge practice, and the considerations guiding the successive steps in the operations, will be discussed in the following. To understand the problems involved, the character and mode of occurrence of Sudbury ore must be kept in mind. Large amounts of disseminated ore are generally present. Although the gangue usually runs only about 50 per cent Si02, the ore hoisted as a rule contains more silica than needed in the smelting operation; until recently this excess was removed entirely by hand picking (in later years supplemented by magnetic sorting methods), a difficult and not very satisfactory method, in which 'the border line between ore and waste is entirely arbitrary, and therefore too much depends on the judgment of the picker.

Jan 1, 1934

By L. H. Shang

The 319 Al-Si alloy is one of the most prominently used aluminium-based alloys in motor vehicle and engine applications, Microporosity present in 319 alloy castings reduces the load bearing capacity of the castings, The quantitative prediction of microporosity levels in Al-Si castings has been a subject of much interest for several years. In this research a new criteria function, tf 1,98 R13° (tf: local solidification time, R: cooling rate) was developed by multiple regression analyses, correlating thermal data from simulation studies to experimentally obtained microporosity values. This new criteria function gives a general prediction of microporosity in 319 Al-Si castings.

Jan 1, 2005

By D. M. Muir

The mineralogy of residues formed during the pressure acid leaching of arid region nickel laterite ore varies according to the salinity of the process water, alkali cation additives and the overall acid loading. In fresh water, hematite is the main iron-bearing leach residue component, together with amorphous silica and hydronium or sodium alunite/jarosite [(H3O,Na)(Fe,Al)3(SO4)2(OH)6]. As the process water salinity increases, or as NH4+ or K salts are added, alunite/jarosite is the kinetically favoured iron-bearing phase accompanied by an increase in acid consumption. The alunite/jarosite appears as two XRD distinct phases with different Fe:Al molar ratios. In weakly saline water, iron-rich alunite/jarosite slowly transforms to hematite and an aluminium-rich alunite/jarosite together with the release of acid. The addition of potassium salts forms a more stable alunite/jarosite whilst the addition of ammonium salts leads to greater transformation of alunite/jarosite at 250°C. Weakly saline process water gives enhanced nickel recoveries, whilst strongly saline process water gives lower nickel recoveries but higher soluble iron because of chloro-complexation. SEM and microprobe analysis shows very little nickel is associated with the alunite/jarosite and hematite phases. Nickel losses to the residues are attributed to adsorption on amorphous silica and to a lesser extent on alunite/jarosite.

Jan 1, 2006

By Robin N. Adair

Abstract -The Halfmile Lake stratiform volcanogenic massive-sulfide deposit consists of pyrrhotite­ rich breccia-matrix sulfides and pyrite-pyrrhotite-rich layered sulfides that form a laterally continuous sheet stratigraphically underlain by an extensive pyrrhotite-chalcopyrite-quartz stringer zone. Mineralization is hosted by a sequence of felsic pyroclastics and volcanic-derived, fine-grained metasediments. The proportion of volcanic to sedimentary rocks indicates increasing vent proximity from southwest to northeast across the deposit area. Fine- to medium-grained felsic pyroclastics and roughly equal amounts of fine-grained metasediments comprise the stratigraphic footwall to the mineralization. Quartz-feldspar porphyritic bodies cut this sequence and may have provided the heat source for exhalite activity. Felsic tuffs, locally crystal-rich, and lesser amounts of metasedimentary rocks make up the immediate stratigraphie hanging wall. This sequence is stratigraphically overlain and locally interfmgered with matie volcanics that contain substantial proportions of felsic fragments. Deposition of sulfides post-dated the beginning of felsic volcanism, which places the deposit in the middle of the Lower Tetagouche Group. Compositions of the volcanic rocks range from basait to rhyolite and exhibit sub-alkaline affinities. Strongly overprinted whole-rock, trace-element, and REE geochemical signatures resulting from mineralizing hydrothermal activity confirm the genetic relationship be­tween the stringer zone and the mineralized sheet. Large-scale D1 folding has overturned the entire sequence. D1 thrust faults and related sheath-like folds have profoundly affected sulfide distribution. D2 is manifested by a penetrative S2 foliation, and D3 is represented by large-scale open folds.

Jan 1, 1992

By A. McLean, W. Q. Chen, W. Yan, M. Barati, Y. D. Yang

In order to maximally remove the harmful impurities phosphorus and reduce the loss of valuable elements from Si-based alloy for production of solar-grade silicon, thermodynamic properties of the Si-based alloy were studied. In this work a new model, the Molecular Interaction Volume Model (MIVM) derived from statistical thermodynamics, was successfully used in the Si-based and Si-Fe-based alloy. The calculation started from binary Si-Fe, Si-P and Fe-P systems, then the thermodynamic parameters of ternary systems could be derived based sub-binary systems. Using the activity coefficients of the elements in the Si-based alloys and the saturated vapor pressure of the pure substance of the components, mass fraction of P during vapor-liquid equilibrium can be calculated. The calculated thermodynamic parameters were compared with experimental data available in different publications, and it is found that the thermodynamic parameters calculated using MIVM model are in good agreement with the measured results. The calculated result shows that the mass fraction of phosphorus during vapor-liquid equilibrium of Si-Fe-P melt increases with the increasing phosphorus content and decreasing temperature. This is an important direction for experimental practice in vacuum or low-pressure EML refining of ferrosilicon for potential production of solar-grade silicon without significant vaporization loss of valuable element.

Jan 1, 2015

By T. Grammatikopoulos, SGS Canada Inc.

"The Nechalacho rare metal deposit, located in the Northwest Territories, Canada, is currently being taken through Feasibility Study by Avalon Rare Metals Inc. QEMSCAN analysis and supplementary electron microprobe analysis were utilized to identify and quantify the mineralogy of the deposit, and determine REE distribution among the minerals. QEMSCAN mineralogy was performed to provide textural information on the mineralization, determine the variability of the ore and identify REE domains, and the liberation and association of the REE minerals. The sample matrix consists predominantly of silicate minerals. The REE minerals include allanite, monazite, synchysite, columbite, fergusonite, and bastnaesite. Zircon is present in considerable amounts and is a REE carrier. Fergusonite and zircon account for most of the HREE, and monazite, allanite, synchysite and bastnaesite the LREE. QEMSCAN mineralogical data is extremely valuable in assessing the mineralogy of the ore. The data are implemented to define the mineralogy of the ore body, support metallurgical test work, and predict recoveries and grades.INTRODUCTIONThe term rare earth elements (REE) is used to describe the 15 lanthanide elements or metals and, more recently, the metals yttrium and scandium, which display similar physical and chemical properties.Economic and potentially economic REE deposits form two main groups, a more commonly occurring “light rare earth element” (LREE) group containing lanthanum, cerium, praseodymium, neodymium, and samarium and a less commonly occurring “heavy rare earth element” (HREE) group which, in addition to the LREE, contains elevated concentrations of the more valuable REE, europium, gadolinium, terbium, dysprosium, holmium, yttrium, erbium, thulium, ytterbium, lutetium and scandium. The first group is hosted primarily by carbonatites and the second by highly alkaline (Na + K > Al) silicate igneous rocks. The LREE are produced mainly from bastnaesite, monazite, etc., while HREE are produced almost exclusively from low-grade secondary ion adsorption clay deposits in which the REE are adsorbed onto the surfaces of kaolinite and halloysite, clay minerals produced by the weathering of granite and sediments. HREE are also found in fegusonite, zircon, xenotime, etc but are not produced presently from these minerals. China is responsible for 97% of the World’s production of the REE, mainly from the giant Bayan Obo, carbonatite-related deposit and from the clay deposits mentioned above.Quantitative automated mineralogy is increasingly being applied to ore deposits. It helps users to understand and improve mineralogical parameters for geological and metallurgical purposes. Data include textural characterization, to quantification and distribution of ore and gangue minerals, liberation and association of the REE minerals. The data can be used to define mineralogical domains and predict the metallurgical response of the ore (Gunning, de Souza, & Grammatikopoulos, 2009)."

Jan 1, 2012

By Mike Dry, Rod Dry

If humanity is truly serious about reducing emissions of carbon dioxide into the atmosphere, today’s power plants burning fossil fuels will have to be replaced by power plants that do not emit CO₂. Unless carbon capture/sequestration becomes practical, the new power plants will be hydroelectric, wind, solar or nuclear installations. Hydroelectricity requires the appropriate geography. Solar installations can only deliver power as and when sunshine is available, and wind installations when the wind blows. Therefore, power from these sources will be intermittent, but the demand for electricity does not follow the patterns of sun and wind. That will require large-scale electricity storage and/or load following by the remaining power suppliers, increasingly so as the use of fossil fuelled power generation declines. Modern nuclear power plants are designed for demand following. However, operating at lower than design output has a negative impact on the economics of nuclear power plants because the overall cost of the electricity they generate is dominated by capital cost. Primary (blast furnace) iron smelting is responsible for a significant part of global CO₂ emissions because the reagent used is carbon. Were it available in sufficient quantity (and at a low enough cost), hydrogen could replace carbon in the manufacture of raw direct reduced iron (DRI), using technology such as modified HYL (Tenova Hyl, 2018) or Midrex (Ravenscroft, 2017). This paper examines a scenario in which, instead of demand following, nuclear power stations are operated at their design capacities and surplus power is used to generate hydrogen in off-peak periods. This hydrogen is then used to replace carbon in the manufacture of raw steel.

Jan 1, 2020

By Y. Yhang, D. C. Sego

ABSTRACT This paper evaluates the potential of freeze-thaw dewatering using Albian mature fine tailings (MFT). Freezing tests were first performed to study the effect of freezing rate on dewatering efficiency. Lower freezing rate resulted in higher thawed solids content and shear strength. Subsequently, large strain consolidation tests were conducted to investigate consolidation behaviour and how it is affected by freeze-thaw. The consolidation behaviour was presented in terms of effective stress versus void ratio and permeability versus void ratio. The results can be used to predict the field behaviour of Albian MFT and optimize the application of freeze-thaw for MFT dewatering.

Jan 1, 2014

By J. Visman

"The Compound Water Cyclone is a concentrator for the wet processing, in bulk, of finely divided materials such as slack coal, fine ores and mineral sands. It was originally developed by the Fuels and Mining Practice Division of the Mines Branch, Department of Mmes and Technical Surveys, Ottawa, for the cleaning of friable slack coals and slurries.Since its introduction in the coal industry in 1962, its application to other materials has also been studied, with special emphasis on simplicity of operation and low over-all cost per ton of finished product .In this paper, a description is given of commercial two-stage units presently available for the processing of granular materials, including wastes a1:1d other low-grade products. A pneumatic control system is used for operating the cyclone under back pressure .and for automatic cut-point adjustment. An account is given of results obtained on coal mineral sands and ores in the Wes tern Regional Laboratory of the Department of Mines and Technical Surveys. Results of several industrial applications are discussed."

Jan 1, 1966

By Link. Theo A.

Introduction Since the discovery of a major oil pool at Leduc, Alberta, on February 13th, 1947, the long spell of 'oil drought' in Western Canada is now being turned into an oil and gas flood which requires immediate action to obtain the optimum economic benefits. The Woodbend, Section 9, and Okalta extensions of the Leduc field itself have been established; the Redwater pool, lying thirty-seven miles northeast of Edmonton, has been discovered and is being drilled up, and the Imperial Schoepp No. 1 or Golden Spike discovery holds promise of something phenomenal in view of the 500 feet of oil-saturated coral-reef porosity whose areal extent is not known. Imperial Stanolind Barrhead No. 1, northwest of Edmonton, revealed the presence of oil in the Madison, and just recently Gulf N.J. Ellis No. 1, some sixty miles southeast of Leduc, found commercial production in the Leduc D-2 discovery zone. In addition to these Paloeozoic discoveries, gas and oil reserves have also been established in the Upper and Lower Cretaceous, which must be penetrated by all tests on the way through the geological column to the Devonian. If ever there appeared to be an index of 'things to come' in the oil industry, this is it. However, without these recent discoveries the picture in Western Canada does and always did, look very promising indeed. A brief survey of the geological setting in Western Canada is the object of this contribution.

Jan 1, 1949

By Biplop Das, E. Herrera, A. Burrows, P. J. Mackey, G. R. F. Alvear Flores

Since the first commercial plant was built at Mount Isa, another twenty ISASMELT™ furnaces have come into commercial operation, and construction of new plants continues. The primary copper ISASMELT™ top submerged lance (TSL) technology continues to attract interest from potential users who seek to smelt productively. In addition to the known benefits of productivity and flexibility, ISASMELT™ operators have also achieved improvements to energy efficiency when switching from their previous technologies. The recent production statistics for operation at Tuticorin, India show that ISASMELT™ has taken the first steps into territory beyond 400,000 t/y (copper cathode basis) and this will likely be the scale chosen by future new copper smelters operating purely on a toll smelting basis. Highly energy-efficient technologies will be expected at these smelters

Jan 1, 2015

By W. A. Lang

"I.-IntroductionAn attempt bas been made in this paper to provide a basis for appraisal of the future of the coal briquetting industry in Alberta by outlining the processes used for briquetting various ranks of coal, by specifying the requirements of a briquetted fuel, by indicating .the status of the industry in the United States, by giving developments in Western Canada, by assessing costs of processing, and by discussing briquetting researches in progress. Much of .the detail bas been omitted since this might mask, rather than reveal, the more important phases of the problem. Reference will be made when possible to published articles where many of the details can be obtained.It should be stated at the outset that, in the writer’s opinion, there are three possible developments in Alberta as regards briquetting: (a) an expansion of the briquetting of the fines of • non-coking and coking coals of semi-anthracite, and of low and medium volatile bituminous rank; (b) the processing of the fines of high-volatile C bituminous coals; and (c) the upgrading of the lower rank high-moisture sub-bituminous coals. Details of the chemical and physical properties of these coals can be obtained in publications of the Research Council of Alberta (1, 2), and of the Fuel Research Station, Bureau of Mines, Ottawa (3).Semi-anthracite and low and medium volatile bituminons coals occur in the mountain areas of Alberta, where, during the upthrust of the Rocky mountains, the coal beds served as the sliding surface. This resulted in the coals being; crushed and consequently they contain a h1gh percentage of fines. In some cases they are high in mineral matter and require to be cleaned before being processed. However, the cleaning of fine coal is both difficult and costly. Both the amount of fines present in the mine-run coal and the amount of mineral matter associated with the coal have increased through the introduction of mechanized mining and through the recovery of coal by stripping operations."

Jan 1, 1950

By M. Krasowska

Dynamics of collision and kinetics of the bubble attachment to hydrophobic solid plates (Teflon) of different surface roughness were investigated. The experiments were carried out in such a way that probability of the collision and probability that the detachment will not occur were equal always 100%. Thus, it was possible to determine effect of the surface roughness on the bubble attachment (three phase contact formation, TPC) only. A high-speed camera (1182 Hz) was used to record the velocity variations, bouncing and time of attachment of the bubble colliding with Teflon plates having different surface roughness (5 different plates). Roughness of the plate surfaces was modified in a mechanical way using different abrasive papers. It was found that the roughness had a crucial influence on the time-scale of the TPC formation and attachment of the bubble colliding with the Teflon plates. Despite high hydrophobicity of all plates (contact angles 1100 -115º) it was observed that at the smoothest surfaces (called "Teflon I" and "Teflon II" and having surface roughness below 1 um) there was no attachment during the bubble first collisions. Prior to the attachment four or more "approach?bouncing" cycles of the colliding bubble were observed there and simultaneously the bubble shape varied rapidly within time intervals below 0.85 ms. Time of contact of the colliding bubble with the Teflon plates was very short; 2-3 ms. These results indicate that during that short time of the collision the liquid layer separating the colliding bubble and the solid surface did not reach a critical thickness of its rupture.

Jan 1, 2006

By S. k. Kim, H. B. Trinh, R. R. Srivastava

"Spent auto-catalyst is a promising secondary resource of platinum group metals (PGMs), which are being extensively used in automobiles catalytic converters to control the hazardous gaseous emissions (CO, NOx and hydrocarbons). Several pyro or hydrometallurgical routes has been employed to recover PGMs from such spent materials but there is no proper process for recovering the other constituents metals. Therefore, it causes the loss of other major constituents like, Al and Mg along with rare earth metal Ce. In the present study, we investigate the dissolution of Al and Mg using sodium hydroxide (NaOH) roasting followed by a sulfuric acid (H2SO4) leaching; thereby concentrating the PGMs and Ce in leached residues. The effect of roasting temperature, time and amount of NaOH were varied. Subsequently, the dissolution behavior of metals in H2SO4 as a function of acid concentration was investigated from the roasted samples. At an optimal condition for roasting at 600°C with 1:1 NaOH-to-catalyst ratio and 60 min duration, the maximum of Al and Mg were dissolved in 1 M H2SO4 solution at ambient temperature (~25°C). Thus obtained leached residues containing enriched PGMs and Ce content can be treated separately for the recovery of these high-value metals.INTRODUCTION Spent auto-catalyst has been considered as a potential resource for recovering the platinum group metals (PGMs) (Jha et al., 2013). The commonly used auto-catalyst is made of cordierite (2MgO.2Al2O3.5SiO2) in which the chloro complexes of PGMs are impregnated onto the surfaces of porous washcoat of alumina substrate (Aberasturi et al., 2011). The average concentration of PGMs in ore are 2-4 g/ton for Pt, 7-2 g/ton for Pd and 0.2-0.5 g/ton for Rh, whereas, an individual catalytic converter weighing about 1 - 2 kg contains on average 1.56 g Pt, 0.62 g Pd and 0.156 g Rh (Upadhyay et al., 2013). Moreover, recovery of PGMs from spent auto-catalyst offers other advantages like, simple process, low cost and less pollution, as compared to recovery from primary resources (Dong et al., 2015).Therefore, technologies to recover PGMs from spent auto-catalyst has become attractive in the recent past and their recycling contribution has been accounted for 35% Pt, 26% Pd and 36% Rh of the quantity consumed in the production of auto-catalysts (Johnson Matthey, 2016)."

Jan 1, 2017

By H. J. H. Pieterse

Agitation requirements in oxidation autoclaves can vary widely depending on the mineralogy of the feed material and the specific process selected. Before selecting an agitation system it is important that the client specify the desired throughput, mineralogy, chemistry, kinetics, compartments, overall retention time, and the desired oxygen utilization. In selecting the agitation system, the factors mentioned above as well as oxygen solubility, oxygen mass transfer coefficients, and specific power are evaluated. Much research effort has been directed toward open tank systems for fermentation and oxidation processes. However, for high pressure autoclave oxidation processes little information is available. In this review the author's experience in the autoclave industry and some of the available literature are utilized to compare the installed power per unit volume with some of the methods proposed for open tank oxidation. Equations that appear to give results close to that experienced in the industry have been identified. Further work is required in this area to develop a higher degree of confidence in the ability to predict the power required for any given case.

Jan 1, 2004

By A. Montera, M. Loken

"The process of blending consistent and predictable feed for the roasters is critical for optimizing product quality and controlling production costs. To assist in this process, online PGNAA slurry analyzers have been installed and evaluated at a Sudbury Ontario smelter. They are used to measure 100 % of the full process stream to obtain elemental composition data in real time. This paper explains the application details at Sudbury and the benefits achieved from their full stream, elemental slurry analyzers.INTRODUCTIONSudbury Integrated Nickel Operations (Sudbury INO), a Glencore Company, consists of two underground nickel/copper mines in Sudbury, Nickel Rim South and, Fraser, along with the Strathcona mill and the Sudbury smelter. The facilities are spread throughout the 60 kilometer-long, oval-shaped geological formation known as the Sudbury Basin (Figure 1). The company has been mining nickel-copper ores in the Sudbury area since 1929. Nickel and copper are the primary focus of operations at Nickel Rim South and Fraser. Other base metals such as cobalt and precious metals are also produced.The Strathcona Mill receives ore from Nickel Rim South, Fraser, and third-party miners to produce two concentrate streams. One is a nickel-copper concentrate for use by the Sudbury Smelter; the other is a copper concentrate which goes to other Glencore operations for smelting and refining. The Sudbury Smelter converts the mineral concentrate into a high grade matte containing nickel, copper, cobalt and platinum group metals. This matte product is shipped to Glencore's Nikkelverk refinery in Norway for further processing. In 2015, the Sudbury INO Smelter completed the first phase of the Process Gas Project (PGP); a series of process changes and capital investments designed to reduce sulphur dioxide (SO2) emissions in accordance with Ontario Regulation 194. A critical element of the planned emissions reduction was the elimination of a higher percentage of sulphur contained in input concentrate streams, which can then be captured and converted to sulphuric acid."

Jan 1, 2017

By Q. Liu, P. Katsabanis, J. A. Meech

A thermohydrodynamic computer code has been used to simulate dust explosions. For sulphide dusts, the thermodynamic predictions are used to investigate the effect of dust concentration, mineral content and inert materials as well as the quantity of sulphur dioxide produced. It was found that the amount of oxygen available for the explosion is very important and that the dust concentration which gives maximum explosion pressures is obtained at zero or slightly negative oxygen balance values. The sulphide minerals were found to have the following explosibility sequence: pyrrhotite, pyrite, chalcopyrite, sphalerite, covellite, chalcocite and galena, which is in agreement with mine experience. The results show that theoretical calculations can be used to predict explosion pressures and toxic gases produced by a dust explosion and therefore they can assist in the design of protective measures .

May 11, 1988