Search Documents

By G W. Wilson, C Panidis

Potentially acid forming (PAF) waste rock contained in dumps formed as a result of open cut mining of metalliferous orebodies are conventionally sealed or covered using a near-saturated, low permeability compacted clay layer, protected with a mulch layer and/or vegetated growth medium. The purpose of the compacted clay layer is to limit oxygen diffusion and the infiltration of rainfall into the dump. Where the aerial extent of the PAF waste rock dump is large, or where suitable clayey material is in short supply, it may be difficult to source sufficient suitable clayey material to form the cover. The paper describes a laboratory-based investigation of combining inert waste rock and tailings to form an alternative seal or cover material. The inert waste rock was sourced from the trafficked surface of a non-acid forming (NAF) waste rock dump, with a maximum particle size of about 100 mm. This was combined with NAF thickener underflow tailings slurry in various mass ratios, and the resulting mixtures tested for their particle size distribution, compaction characteristics, soil water characteristics (relationship between suction and volumetric moisture content), and saturated hydraulic conductivity. The mixtures tested ranged in consistency from those dry enough to be compactable, to those with the consistency of wet concrete that lend themselves to placement without the need for compaction. The laboratory test results showed that the suitability of the mixtures as seal or cover materials is very dependent on the particle size distribution of the mixture, with well-graded mixtures having substantial fines performing best.

Jan 1, 2003

By Sheng X. L

The Jurassic coals at Datong are characterised by their strong, massive sandstone and conglomerate roofs which fail suddenly over large areas, crushing pillars and creating destructive windblasts. collapsed areas have exceeded 180,000m2 and windblasts have extended over one km underground and 200m on the surface and have been accompanied by subsidence troughs on the surface. Scientific analysis has researched premonitory signs of caving and the nature of windblasts leading to considerations of alternative mining methods and ways of dissipating the energy of windblasts to reduce their damage and danger..

Jan 1, 1992

The Inglewood Gold Project consists of several titles in and around the Inglewood and Wedderburn Goldfields which were purchased from Strata Mining Corporation (now Excalibur Mining Corporation). The Inglewood goldfield has a historical production of approximately 160 000 tonnes at 23 grams per tonne. The company has reopened and developed the Maxwells reef, picking up a high-grade shoot (Max Shoot) identified and worked by Goldquest et al up until 1994. Production ceased on a low gold price, rapidly reducing vein size and a requirement for further development. Greater Bendigo Gold Mines Ltd (GBM) has undertaken the development and encountered the mineralised vein in an increasing size setting with high grades and the existing mine development has access to a further shoot to the north (Max North Shoot). The Maxwells reef also contains the Woolf shoot south of the Maxwells shaft and an inferred resource of ~20 000 ounces is contained from 60 m below surface. Best intersection 2.9 m at 50 g/t. The Maxwells reef area produced approximately 20 per cent of the Inglewood goldfields production and GBM is preparing to increase its exploration efforts across the rest of the field. A processing plant has been constructed at the Maxwells mine site, which is capable of treating tailings, hard rock and alluvial material utilising gravity recovery. The existing Maxwells tailings have been excavated and treatment commenced. It is intended to produce a sand product from the tailings for resale and to reduce the storage requirements per tonne. Several large water dams constructed by Goldquest in the 1990s are being re-engineered to enable storage of significant tonnages of tailings. A level of surface and underground production is planned for 2008 and this is to be expanded into 2009 and beyond. The long-term future at Inglewood is envisaged as structural repeats at depth below the current workings and a project plan to gain deep access will be prepared on successful drilling results.

Jan 1, 2008

The Callie Underground Mine is located in the Tanami Desert 560 km Northwest of Alice Springs in the Northern Territory and is currently operated by Newmont Australia Limited with all mining activities carried out by Henry Walker Eltin. Callie was discovered in the region in 1991 with the box cut portal commenced south of the pit in 1995 and underground ore production commenced in 1998, after completion of the profitable Callie Open Pit. Development is currently occurring at depths of over 700 m with the decline currently below the 640 Reduced Level (RL) level (surface RL of 1400) with production haulage from 600 m below the surface. The combination of auto compression, a moderate geothermal gradient of 2¦C/100 m and diesel heat transfer causes the wet bulb temperature of intake air at the bottom of the mine to be typically 5¦C higher than on the surface. Wet Bulb temperatures can be up 5¦C higher again in active areas under secondary ventilation. During the 2002/2003 wet season many activities in the lower levels of the mine were stopped due to miners experiencing adverse heat related symptoms or the temperatures exceeding the Underground Heat Management Procedure stop job criteria of 32¦C wet bulb. To improve the working environment, combat the heat related illness and improve operational efficiency, a temporary 1.8 MW refrigerated cooling plant consisting of three 600 kW modules were installed underground to provide bulk air cooling for the lower levels of the mine during the 2003/2004 wet season. Several studies have been conducted in relation to future ventilation demands at Callie and all came to the conclusion, that some mine cooling will be necessary for Callie to meet the high production and development demands. This paper will describe the ventilation network at the Callie Underground operation focusing on the installation, operation and effectiveness of the temporary underground refrigeration plant.

Jan 1, 2005

By T Cutts

Since 1989 Kalgoorlie Consolidated Gold Mines has managed the Kalgoorlie gold operations of joint venture partners Normandy Mining Ltd and Homestake Gold of Australia Ltd. Current production from the Fimiston Open Pit is approximately 650 000 ounces per annum. The mine incorporates a multitude of narrow shear hosted, subvertical lodes, predominantly within Golden Mile Dolerite. Traditionally KCGM has used blasthole based grade control in the Fimiston pits. A single sample is taken from vertical production blastholes, drilled on ten metre benches. This process was improved with the addition of infill drilling along blasthole rows to provide additional samples across strike. However the limitations of adequately defining subvertical mineralised structures with vertical blastholes remain. In 1997 the first of two trial areas were drilled with close spaced, inclined Reverse Circulation (RC) drilling. These tests indicated that RC based grade control had the potential to provide significant advantages. These include:improved delineation of mineralised structures, particularly across strike; reliable short-term mine schedules based on the advance data available from drilling over three benches; and the angled RC drilling is capable of providing samples of near stope and stope fill material which often remains unsampled by blasthole drills due to the safety constraints around unstable underground openings. Based on the success of this initial work RC based grade control was gradually implemented across production areas commencing September 1998. Some of the many challenges faced include:development of effective procedures and systems for the planning, logging, interpretation and modelling of the RC data; obtaining adequate drill coverage due to mine scheduling constraints and restricted access around underground openings; requirement for integrated systems to handle either blast hole or RC data; and development of effective methods to evaluate the performance of RC grade control. RC based grade control is delivering significantly improved lode definition, grade estimation and subsequent ore classification.

Jan 1, 2000

The process of mine planning at AnacondaÆs nickel and cobalt laterite operation located at Murrin-Murrin in the Northern Goldfields of Western Australia is carried out in a number of stages in an endeavour to determine the optimum mining sequence in order to maintain supply to the 4 Mtpa plant subject to operational constraints. The 296 Mt @ 0.99 per cent Ni and 0.064 per cent Co ore reserve (based on a cut-off grade of 0.8 per cent Nickel) is spread geographically widely over three regions comprising Murrin North (15 km + 15 km), Murrin South (7 km + 16 km) and Murrin East (5 km + 13 km) (refer Figure 2). The nickel mineralisation has been broken up further within each region into 18 separate manageable block models representing the 32 different deposits. The models are based initially on the 50 m + 50 m resource drilling for long term planning and updated with 12.5 m + 12.5 m grade control drilling prior to mining. Each of the individual block models are optimised using Whittle 4X software to provide the shells used as the basis for each of the 126 pit designs. The pits are generally nested with starter pits targeting the higher value shells with subsequent pits incrementally cutting back ultimately to the life of mine shells. A series of steps including: the coding of the individual pits into the block model; data export; TCL scripting (to calculate additional economic and tracking information); importing; and re-blocking; completes the transfer of the data into a MineMax (mixed integer linear programming schedule optimising software) model. Using MineMax and the application of operational and production constraints allows the optimisation, assessment and economic evaluation of alternative scenarios in order to determine the optimum life of mine plan and schedule.

Jan 1, 2003

With the use of 86 rock drills of the jackhammer type at the West Lyell Open Cuts of the Mt. Lyell Mining & Hailway Co., it is of importance to determine the economic as well as the physical life of these machines. With this purpose in mind records have been kept of the footage bored and the cost of new parts placed in each machine, and the following procedure adopted.A graph is plotted for each machine showing the footage bored as a horizontal line and at each 5,000 feet of boring the total cost of new parts noted on this line. (See l"ig. 1.) Thus at a glance it is possible to see... the amount of work done by each machine and the money spent on it in new parts. However, it is difficult to visualise from this graph the increase in the cost of new parts for each machine as its life advances. To obviate this difficulty a curve is plotted with the cost of new parts as the vertical component and the distance bored as the horizontal component. As before the cost of new parts are taken at each 5,000 feet bored. (See Fig. 2.) The curves so obtained are particularly interesting for two reasons:1. Each machine has its characteristic curve.2. The curve always steepens.Some machines are found to have relatively flat curves, others flat curves for approximately 15,000 feet of boring, and others steep gradients from the begining.This demonstrates that it is not always economic to discard a drill after it has been in service for a certain length of time or after it has bored a specified number of feet. Each drill has its own characteristics and so must not be regarded as one of a class, but considered on its own performance.The following use of these curve diagrams has been made to determine whether a machine has reached the end of its economic life. Figure 3 shows...

Jan 1, 1942

By M Kizil

Mining Engineering Degree programs have traditionally had a practical emphasis and have been highly vocational in nature. However, over the years, there has been an increasing attention to the more scientific aspects of the discipline. More recently, the professional institutions, the industry and the community at large have placed increasing emphasis on the broader aspects of the professions: management, finance, humanity, environment and social issues. Notwithstanding this, there has been a continuing emphasis on the practicalities, and most Mining Engineering programs are still strongly vocational in nature. But employers of new graduates complain about the graduatesÆ lack of practicality and readiness for employment æat the sharp endÆ on the mine site.This paper briefly describes some of the more recent developments in the Mining Engineering Degree program at the University of Queensland that attempt to address the problem. Particular attention is paid to alternative learning programs, including applications of virtual reality, practical experience at the University Experimental Mine (UQEM), and the Undergraduate Site Learning Program (USLP).

Jan 1, 2002

In this paper presented are the criteria used when assessing the harmfulness of shocks affecting the buildings. Those criteria are based on the value of speed or accelerations of building vibrations. Presented is the scale of harmfulness of vibrations of Langefors and Kihlstrom, Bureau of Mines, and SWD contained in the Polish Norm PN-85/B-02170. The parameters of the mining shocks measured by the Lubin coal mine station were compared with the parameters calculated as per the correlations (regression curves). The average acceleration calculated from the correlations for eight measurements is only two per cent higher than the actual one. But the average frequency of vibrations calculated from the correlations for eight measurements is as much as 2.22 times lower than the actual one. In order to analyse whether that takes place in the whole range of the energy of shocks compared were the results of calculations from the correlations for various magnitudes of shocks and various distances from their epicentre with the results of the measurements. From that it follows that only for the shocks of the highest energies the lowering of the frequency of vibrations by two times causes movement from the higher zone of harmfulness to the lower one (for example from the IV to III). In the one-family houses in Lubin there were the damages that are characteristic for not only for the III but also for the IV sphere of harmfulness as per the SWD scale. That should be explained via further research and maybe it would be feasible to draw out a new correlation to determine the frequencies only for high values of energy of shocks and determine the preciseness of the acceleration and frequency correlations used presently.

Jan 1, 2003

By R J. Everett

The mining industry is beginning to adopt quality systems based on the requirements of International Standards for quality assurance, such as the ISO 9000 series. Indications from similar industries are that considerable benefits are to be had from their adoption. This paper describes the use of the International Standard ISO 9001 for quality assurance within BUKA Minerals Limited. This provided guidance for the development of a clear statement providing agreement on the processes to be followed and the outputs required when dealing with outside service providers. Discussion focuses on the interaction with BUKAÆs consultants and contractors during the specification stage, resulting from the application of quality assurance techniques. Risk analysis was used to identify and manage the risks associated with the companyÆs contract for geotechnical and mine design services and the tender for a mine development program of work during the feasibility stage of the project. Setting acceptance controls for the deliverables from such contracts is traditionally fraught with difficulty. BUKA used Failure Mode and Effect Analysis for exposing underlying risks that were not effectively being countered. The briefs were reviewed and additional controls were developed to manage the risk. These controls have provided clearer instructions to the consultants and contractors, indicated audit points for the company and defined the deliverables. There exists within the company, and among its outside service providers, a clearer understanding of what is to be achieved and how it will be measured. The process has imparted considerable confidence to both parties on how the work will proceed and what outputs are to be provided. Some discussion is provided on how quality principles are being applied throughout industry and commerce, generally, and how they may apply to the mining industry. The paper argues that, far from being an appendix to the tendering process, Risk Management should be a mandatory step integrated into the definitions of the work.

Jan 1, 1998

By J Garritsen, P F. Wells, M Xu

IncoÆs Clarabelle mill currently processes ores from eight mines in the Sudbury basin area in Ontario, Canada. The ore from the Garson mine contains a much higher concentration of arsenic than the other ores. Adding this ore into the feed to the mill has resulted in an increase in arsenic content of the Cu-Ni bulk concentrate to a level that significantly affects the smelter operation, and more importantly the efficiency of Cu-Ni separation in the Matte separation plant. The arsenic occurs mainly as gersdorffite (NiAsS), with a small amount being in the form of cobaltite (CoAsS). Extensive laboratory tests on depressing arsenic in Garson ore flotation have been conducted and two reagent suites have been identified as effective arsenic depressants. One is the so called MAA depressant which is a mixture of magnesium chloride, ammonium chloride, and ammonium hydroxide. This reagent combination was reported to depress other arsenide minerals such as arsenopyrite (FeAsS) and enargite (Cu3AsS4). However, in this study for the first time it has been shown to have a depressing effect on gersdorffite. The other reagent suite, a mixture of triethylenetetramine (TETA) and sodium sulfite, that has been reported as an effective pyrrhotite (Fe1-xS) depressant in pentlandite ((NiFe)9S8) flotation, has not been reported as gersdorffite depressant before. The effectiveness of both reagent suites is more pronounced when the arsenic minerals are oxidised through pulp aeration or the addition of hydrogen peroxide. With a flow sheet consisting of a magnetic separation, rougher- scavenger flotation, followed by regrinding and cleaning of combined magnetic and scavenger concentrate, the arsenic recovery to the final Cu-Ni bulk concentrate was reduced from 73 per cent in baseline test to less than 30 per cent with either reagent suite at no decrease in nickel recovery. The TETA/sulfite reagent combination has the advantage over the MAA suite in that pyrrhotite is also depressed, rather than being activated, and the copper and nickel concentrate grades are therefore increased.

Jan 1, 2005

By M Reisi, H Waterer, M Savelsbergh, F Engineer

The Hunter Valley Coal Chain Coordinator (HVCCC) Limited is the primary planning organisation responsible for the export of coal through the Port of Newcastle, Australia. HVCCC stakeholders include producers (mining companies), rail track owners, above rail operators, and terminal operators. The HVCCC is tasked with coordinating the activities of all the corresponding parts of the coal export supply chain so as to maximise the system efficiency. The HVCCC also has a forward looking planning role: with demand for coal expected to double in the next decade, strategic capacity planning is a core activity for the HVCCC. Optimisation and simulation models are key aids in such activity. They are used to suggest and evaluate infrastructure expansions and operating policy changes. These models require input data in the form of shipping stems, which are arrival streams of ships at the port, together with their cargo types and composition, and date and time of arrival.Although everyone is familiar with the expression ægarbage in equals garbage outÆ, relatively little research is dedicated to the issues surrounding input data generation. In this research we seek to redress this, and have developed a method for generating high quality shipping data. Shipping stems used as input should be realistic, reflecting key characteristics of historical patterns. They should accurately represent future demand scenarios. Yet they should also have controllable parameters that can be used to test what-if scenarios, such as are required by the HVCCC to answer questions about future infrastructure or operational plans.Here we review our process for achieving this, and give a case study analysing the effects of different shipping stems on the performance of the coal chain, as measured by a capacity assessment tool. The latter is an optimisation model that takes shipping stem and infrastructure data as input, and calculates key supply chain performance metrics. The potential benefits of alternative demand management strategies are analysed by measuring the performance of the coal chain given different shipping stems obtained via the stem generatorÆs controllable parameters.

Sep 26, 2011

The first 12 m diameter rakeless thickener in the Australian gold mining industry was installed to treat plant tailings at the St Ives gold plant in April 2000. The plant processes approximately 3.2 M tonnes of ore producing about 430 000 oz of gold per annum using conventional crushing, grinding, gravity and carbon in pulp processing methods.The main benefit sought from the thickener was to improve water recovery in the plant and provide water for a 55 000 oz per annum heap leach operation. The thickener design indicated that more than 128 m3/h of overflow water could be returned directly into the plantÆs water circuit, relieving the demand on the borefields. The resultant surplus in the water circuit would then be available for the heap leach project. Based on laboratory and pilot plant scale tests conducted by EIMCO the thickener was designed to handle up to 700 m3/h of tailings slurry (450 tph of solids) with a 40 per cent oxide component in the ore blend. The normal plant throughput is 565 m3/h of slurry (400 tph of solids). Gold mineralisation in most areas at St Ives comprises quartz-sulphide vein and breccia lodes with common albite-biotite-chlorite alteration assemblages. There are well developed supergene gold horizons in the clay-oxide profile above most of the deposits (Osborne, 2002). This results in a wide variety of ore types being treated. At times 40 - 50 per cent of the ore may be oxide in nature. After some commissioning difficulties associated with instrumentation, the thickener has performed satisfactorily although it has not reached its design capacity. The maximum density achieved under normal operating conditions with 20 per cent oxide ore is about two per cent below the design. The thickenerÆs performance deteriorates further with increasing amounts of oxide ore in the blend. The thickener has provided sufficient water for the successful operation of the heap leach and has also provided some down stream benefits for the gold plant by way of pH and cyanide conditioned thickener overflow water.

Jan 1, 2002

In November 1992, the Internal Revenue Commission (IRC) was formed from the rperggr of the Papua New Guinea Taxation Of- fice (PNGTO) and the Bureau of Customs, and now has the re- sponsibility for the administration of direct and indirect taxes on a national basis in Papua New Guinea (PNG). Since that date we have undertaken many initiatives to make the new organisation more efficient and responsive to clients' needs. Income Tax The mining industry is catered for, in respect of income tax, un- der a separate taxation regime within the Income Tax Act (ITA), Division 10, as well as some general provisions within that Act as may be applicable. Division 10 is itself broken up into subdi- visions to cover the different types of mining leases, namely Spe- cial Mining Leases (SMLs) and Mining Leases (MLs), and peri- ods of time during which those sub-divisions apply. Ring Fencing Income tax assessed on the mining industry, with the exception of Mining Leases (these will be explained later), has a project basis of assessment, that is, each project is assessed separately as if the taxable income of the taxpayer from operations attributable to the project was the only assessable income derived by that taxpayer. This is often referred to as "ring fencing". This is an important point to consider because losses from unsuccessful projects cannot be set off against income from those that are suc- cessful, except in very limited specific circumstances, such as where an unsuccessful exploration licence is cancelled or surren- dered. The project basis of assessment applies to both resident and non-resident companies. A relaxation in the 'ring fence' provisions was applied from 1st January 1995, where ten percent of exploration expenditure, in- curred in areas outside of Special Mining Leases and Petroleum Development Licences in a particular year of income, can be claimed as an outright deduction which is limited to ten percent of the tax otherwise payable in that year. This was introduced to encourage exploration in PNG.

Jan 1, 1997

By D Jordan, R Wilmoth, J LeFever

Exposed, open pit mine highwalls contribute significantly to the production of acid mine drainage (AMD) thus causing environmental concerns upon closure of an operating mine. Four innovative technologies were evaluated under the US Environmental Protection AgencyÆs, Mine Waste Technology (MWTP), Prevention of AMD Generation from Open Pit Highwalls Demonstration Project. This project is funded by the US Environmental Protection Agency (EPA) and jointly administered by the EPA and the US Department of Energy (DOE) through an Interagency Agreement. The objective of the field demonstration was to evaluate the technologies ability to decrease or eliminate acid generation from treated areas of the highwall in comparison an untreated highwall area. The field demonstration was performed at the Golden Sunlight Mine (GSM) a subsidiary of Placer Dome US, located near Whitehall, Montana. GSM is an operating gold mine. The highwall at GSM was divided into five plots measuring 15.24 by 15.24 m and each technology was assigned a plot with the fifth plot being used for comparison as a background control plot. The four technologies were spray-applied. The applied in situ treatment technologies included: a modified, furfuryl alcohol resin sealant, utilising wood and agricultural by-products to coat the rock surface; EcobondTM ARD, a phosphate based process that forms a stable, insoluble compound, coating the rock surface; and two AMD passivation technologies, magnesium oxide and the Dupont technology developed to create an inert layer/coating on the pyrite, preventing oxidation. The technologies were evaluated using the following methods: ASTM D 5744-96, accelerated weathering of solid materials using a modified humidity cells; mine wall residual wall rinse sampling; microscopy; and core drilling followed by water injection testing. The following paper describes the technologies used for passivation of acid generation from the highwall, the field demonstration, and the testing results from the background and each technology plot.

Jan 1, 2003

The following is a brief summary of the Bulli Colliery and its method of operation when Australian Iron and Steel Ltd. took control.Bulli Colliery is situated about a mile west of the village of Bulli and is some 10 mUes north of the Australian Iron and Steel Company's Steelworks at Port Kembla.The mine is owned by Australian Iron and Steel Limited, who purchased it in 1936 from the liquidators of Bulli Colliery and Coke Works.It is one of the oldest working coal mines in Australia, having been opened about 1858 and has worked more or less continuously since that date.The seam worked is the No. 1, or Bulli, Seam, which outcrops along the escarpment of the Illawarra Range and is generally operated by tunnels, the portal at Bulli being some 440ft. above sea level.The colliery holding is fairly extensive, but the coal seam over a large portion of the area within two miles of the outcrop has been more or less destroyed by an intrusion of basalt.At present there is no coal being worked within a distance of about 21 miles from the surface, the farthest workings being about four miles from the tunnel mouth.The existing main haulage road, for the first two miles from the portal, is not straight; it is very narrow over fairly long stretches and has many changes of grade varying from 3% in favour of the load to 13% against the load.The dumping station and screens are situated close to the portal of the haulage tunnel, and at this point the coal is loaded into railway hopper waggons, which are then hauled by rope to the top of a self-acting incline. The waggons are lowered down the incline, a distance of approximately! mile, the ruling grade being about 18 %.From the bottom of the incline, waggons are hauled by Company's steam locomotive to exchange sidings from whence they are taken by New South Wales Government Railway engine to the Company's Steelworks at Port Kembla.

Jan 1, 1947

By P Louden, C Rothnie, G Showers

Tiwest employs several methods to assess the quality of heavy mineral concentrates in ore and process samples. Mineralogy is determined using a method called MA98, developed in conjunction with JKMRC over the last three years (Zhang and Whiten, 2001). A range of other techniques are also used to characterise ore, heavy mineral concentrates and mineral products. MA98 is the culmination of efforts since 1989 to determine mineralogy from chemical analysis without recourse to heavy liquid fractionation, which has traditionally been used to discriminate between light-heavy , zircon, rutile and leucoxene. The major advance with MA98 is the use of statistical mass balancing for all chemical species, as opposed to reliance on key chemical species for each mineral. Three magnetic fractions are analysed by X-ray fluorescence spectrometry, with a minerals balance performed for each. Heavy mineral concentrates processed by this method include drill samples, process samples from the wet concentrators and Dry Mill, and mineral products. TBE can be avoided for higher heavy mineral grade samples since quartz is determined from SiO2 balance. In this sense the method is sufficiently universal and robust to cope with a wide range of sample types and compositions. The MA98 algorithm provides abundant information in addition to mineralogy, including TiO2 and Fe2O3 grades of ilmenite and leucoxene, and concentrations of weakly magnetic zircon and kyanite. Information such as this is invaluable in tracking different minerals through the processing plants. Other ore assessment procedures used by Tiwest provide for modelling of orebodies by mineral sizings, Fe in zircon, and FeO and U+Th in ilmenite. Microscopy is used to provide important qualitative information such as grain shape, surface staining and degree of cementing. These quality measurements are included with mineralogy in geological ore models and are available for mine scheduling. In using the above methods to characterise heavy mineral concentrates, Tiwest is better placed to predict and monitor plant performance and product quality from any ore zone.

Jan 1, 2001

By Alesse V, Belardi G

A new class of collectors, Mercapto-Benzo-Oxazoles (MBO), exerting selective action on copper sulphides in the presence of Pb, Zn and Fe sulphides (galena, sphalerite and pyrite), has been synthesised in co-operation with Enichem's Donegani Insitute. The collectors have a mixed aliphatic-aromatic structure and contain functional groups which form chelates with copper. Some reagents of this class having hydrocarbon chains of various lengths have been laboratory tested on a complex sulphide ore containing chalcopyrite, galena and sphalerite in pyritic gangue. Comparative flotation tests have permitted selection of the best collector for chalcopyrite, namely Methyl-Mercapto- Benzoxazole (MMBO). Systematic flotation tests have been performed with this reagent, varying collector concentration, grain size of the feed, pH and flotation time. The results obtained show that the synthesised collector is much better than potassium-amylxanthate (KAX) as regards selectivity towards Pb and Zn. Moreover, it is possible to work at natural pH (6-7) and the flotation rate is higher. In fact in the rougher stage with 80 g/t of collector at natural pH, a copper grade of 7.14 per cent was obtained with a recovery of 73.87 per cent, while the grade with KAX did not exceed 2.11 per cent for a recovery of 73.54 per cent. The amount of Pb and Zn reporting in the copper concentrate was eight per cent and ten per cent respectively, while with KAX it was no lower than 24.34 per cent and 22.71 per cent in that order. After two minutes flotation a copper grade of 5.2 per cent with 52 per cent recovery could be attained, against a grade of 2.5 per cent and a recovery of 44 per cent in the case of KAX. The efficiency of this new collector has been ascertained on two samples of complex sulphide ores of diverse mineralogical composition.

Jan 1, 1993

By Eaton R. A

The design of most underground mining machines shows little evidence of regard for ergonomic principles and operator comfort. Likewise, efficiency and ease of operation often appear to have been given little consideration in machines where ruggedness and simplicity have tended to dictate the configuration. Improvements in productivity are amongst the benefits to be gained by a different approach to machine design. The paper describes the philosophy and features of a test bed Load-Haul-Dump Vehicle undergoing trials at Mount Isa Mines. This machine is the outcome of a Research and Development Programme conducted by the Department of Mechanical Engineering at the University of Queensland and Mount Isa Mines Limited. The diesel powered test bed features an enclosed, air conditioned cabin, with a suspended operator's control station and electrically operated controls. An electronically controlled hydrostatic transmission incorporating wheel slip control, is another innovation. The performance and operator acceptance of the machine has led to adoption of most of the concepts in a new machine now being put into production.

Jan 1, 1987

The Mungana group of mines, in the Chillagoe district, yielded 334,000 tons of ore giving 31,831 tons of lead, 7,907 tons of copper and 3,228,600 ounces of silver. The Girofla mine produced approximately 220,000 tons of ore, and with the Lady J ane mine supplied most of the ore from this centre. The deposit was discovered in 1888, but active development did not commence from the main shaft until 1898. A subsidiary of the New Chillagoe Railway and Mining Co. Ltd., the Mungana (Chillagoe) Mining Co. Ltd., worked the mine from 1902 until 1914, selling copper, copper-lead, lead ores and fluxes to the smelters at Chillagoe. The smelters stopped operations in 1914 when the richer ores of the Girofla had been worked out and production from the Lady Jane had ceased due to heavyground and fire. The Girofla shaft was 823ft. deep with a cross-cut at 810ft. At the 710ft. level contour drives had delineated the orebody, which had been stoped about 10ft. above the level. Except for flux ores which had been stoped only for favourable smelter tariffs, the orebody was practically exhausted above the 610ft. leveL Under company ownership the mine yielded 139,265 tons of an average grade of 4.QlYr copper, 16.2% lead and 12.5 oz. per ton silver.In 1921 the Queensland Government re-opened the mine and worked it until 1927. The North Lode (Fig. 2) was discovered almost immediately at the 100ft. level and was worked down to the 410ft. leveL The ore from this branch and the completion of the stope at the 710ft. level yielded about 80,000 tons of ore averaging 0.4 copper, 9.8 lead and 7.8 oz. per ton silver during this period.

Jan 1, 1953