Search Documents

By S R. Grano

The selection of the proper frother, specifically for a given ore, is essential in flotation. Traditionally, strong and stable froths are required in the scavengers, where metal recovery needs to be maximised, while selectivity must be achieved in the roughers and cleaners, where grade of concentrates is the main issue. The physical properties of a froth are determined both by frother type, by process water composition and by the amount and nature of the suspended particles. The evaluation of different frothers, in terms of metallurgical performance, is complicated at plant scale, since it may lead to periods of malfunctioning of the process and unacceptable decreases in recovery. On the other hand, evaluation based on frother chemistry only, is often unsatisfactory, because the frothing response is strongly ore dependent. A procedure, and proper tools, was developed at the Wark in order to perform the screening of candidate frothers at batch scale on real pulp samples. The main parameters related to froth stability (half-life time, froth height) are measured after introducing the pulp samples into a foaming column, where different conditions in terms of frother addition, agitation and aeration can be maintained. The approach has been applied to the selection of frothers for the flotation of an Australian sulfide ore. Procedure and results are discussed.

Jan 1, 2006

By P Bourke, S Ronkainen

Since the early days of flotation, process technicians have known that the speed at which the froth is recovered over the lip of the cell has a very direct and consistent influence on the grade and recovery of the circuit. No plant would deny that, even to this day, one of the most important aspects of a process technicianÆs job is ensuring that the froth is moving at a desired and controlled speed over the lip. Unfortunately, process technicians cannot watch the froth throughout the entire shift, as there are always other problems to attend to. A considerable amount of work has thus been done to develop a æsystemÆ that automatically measures the speed of the froth. This measurement would then be used in simple controllers to emulate the steps taken by the process technician in correcting deviations of the froth speed from its desired level. Many of the earlier attempts to measure speed were ineffective, as they were unable to cope with turbulence on the froth surface. The FrothMasterÖ instrument makes use of machine vision technologies to measure the speed of the froth over the lip of a cell at a very high sampling rate. This instrument produces an extremely reliable and accurate measurement of the froth speed (as well as other parameters such as bubble size and froth stability). As we will show, the effectiveness of the speed measurement in controlling the performance of the plant is a testimony to its reliability. Three FrothMasterÖ units have recently been installed on the Cadia Hills Gold Mine in New South Wales (Australia). The objectives of this installation were:to control the mass-recovery of two Tank Cells in series on the same level where differences in the hydrostatic head between the two cells result in the cells pulling inconsistently with respect to each other; control of the concentrate grade (per cent copper) from the first rougher; reduction in the frother consumption in the rougher circuit by monitoring the froth speed. A simple controller was designed to react to disturbances in the same way that human operators react. This was done after consultation with the metallurgists and the process technicians at Cadia. The controller had two functions: Stabilisation: The stabilising controller made use of three manipulated variables (level, frother addition rate and aeration rate) to control the froth speed to a setpoint. Optimisation: The optimising controller adjusted the froth speed setpoint based on deviations of the grade (measured in real-time by the OSA) from a setpoint. The plant metallurgist adjusted the grade setpoint based on information about the ore. The results from a 21-day trial have shown the following:The ratio of concentrate mass-recovery between two cells in series on the same level has been successfully balanced, thereby overcoming problems due to differences in hydrostatic heads. It is possible to control the speed of the froth, in mm/s, to within five per cent of its setpoint using the aforementioned manipulated variables. It has also been shown that, for reliable control, it is necessary to control more than just one variable (eg level or air). The grade of the first rougher concentrate has been controlled to within 0.3 per cent of the grade setpoint for long periods of time, which has important implications for the circuit recovery. The frother consumption has been reduced significantly. This paper will thus show that substantial progress has been made to demonstrate the value of using on-line froth speed measurements in flotation plant control to obtain real financial benefits.

Jan 1, 2000

By M Dunglison, P M. Cameron

Simultaneous mass-balancing of a mineral processing flow sheet results in adjustments to each data point that reflects the accuracy and precision across the full set of data. In this way, all the good work that goes into designing the sampling and analysis protocol for each sample point is leveraged in order to produce a æbetterÆ set of balanced numbers for every sample point in the circuit. Few operating plants employ whole of circuit balancing techniques to produce reported operating results. This situation is changing with the application of mass balancing technology which utilises redundant data for production accounting and metal reconciliation from product to ore source across multiple phases and multiple time periods. Mine and plant data can now generate credible information to improve productivity. Mine and plant personnel can now use consistent data sets for review and planning. Decisions based on balanced data can be made quicker and with increased confidence.

Jan 1, 2005

By M Stewart, J Petrie, L Basson

This paper explores tools which have the potential to promote and assess the formation of partnerships between the minerals and energy industries to enhance the economic, environmentally responsible and socially acceptable use of energy. There is a need to look at energy provision and energy services in an integrated manner with key drivers for economic development û both locally and regionally. The minerals sector will remain highly significant to regional economic development in a number of globally significant regions in the medium term. Furthermore, mining, minerals and metalsÆ projects are both consumers and, in some cases (potential), generators of large amounts of energy (electricity included). It is therefore appropriate to focus on the promotion of partnerships between energy providers and the minerals sector which seek to improve resource efficiency within the combined minerals/energy envelope, guided by the tenets of Sustainability.Whilst there has been considerable development of systems analysis tools in recent years to address this sort of æcomplex systemsÆ analysis (Life Cycle Management, Cleaner Production and Industrial Ecology arguments for example), there is no effective roadmap available to decision makers to guide the selection and exploitation of these tools in different contexts. Our previous work developed a Decision Support Framework (DSF) which provides some guidance here, but only within the context of coal-based power generation. The DSF employs the tools of Multi Criteria Decision Analysis (MCDA), within which trade-offs between competing objectives are explored in such a way that alternatives can be compared without necessarily reducing all the different cost and benefits to a common basis (eg a monetary basis). Even if the existing DSF is extended to include all aspects of supply-side management, it is still lacking the necessary tools to analyse energy providers as dynamic network partners within minerals projects (or indeed any resource or manufacturing sector). New models are required for this, which firstly, seek to characterise such network structures, and secondly, enable the application of the necessary analytic tools to exploit these partnerships and networks for optimal performance.This paper explores the development of such an integrated set of network analysis tools, and their relation to the DSF. Due consideration is given to the choice of the attributes needed to characterise partnership linkages and network integrity (eg security of supply of electricity), and the efficiency of material transformations within any node of the network (as a function of energy consumption), and the impact that this has on the viability of other linkages (eg due to reduced availability of raw materials). We discuss how these perspectives help shape the form of objectives to be considered by MCDA.

Jan 1, 2004

By X Yang, T Zhang, Z Li, Z Yan, M A. Williams, S Qin, P Wilson

Continuous development of complex new steel grades to meet the ever-increasing demand of high performance causes recurrent issues in steel continuous casting such as surface quality defects (eg cracks, depressions, deep oscillation marks) and productivity challenges (eg faster casting, near-net shape casting). Continuous casting of steel is a highly successful metallurgical process. Much of this success can be attributed to the performance of the casting powder that is added to the top of the mould, creates a liquid slag pool as it is heated, and forms a slag film between the watercooled copper mould and steel shell during its passage down the mould. Mould powder selection is a compromise between the conflicting requirements of heat transfer and lubrication. In an EU RFCS (Research Fund for Coal and Steel)-funded project, various techniques are developed to offer the opportunity to adapt the slag film to meet the conflicting needs in different parts of the mould such that mild cooling can be generated in the meniscus, mid-broad face or corner areas whilst maintaining lubrication and offering higher cooling rates in other areas of mould. This has significant potential to address the industrial issues in product quality and productivity of continuous casting. This paper reports, as part of the EU RFCS project, the determination of crystallinity and porosity in slag films for casting challenging and innovative steel grades using new methods. In comparison with the methods such as X-ray powder diffraction (XRD) analysis and optical microscopy / scanning electron microscopy (OM/SEM) analysis that are currently adopted by the industries, EBSD (electron backscatter diffraction) has been employed to determine the crystallinity of the slag films taken from industry casters. X-ray computed tomography (XCT) plus 3D image reconstruction has been used to determine the slag film % porosity with pore volume, pore size distribution, and pore location, which can be linked with the performance of the slag films during casting different steel grades.

Jun 19, 2024

By S Sineva, E Jak, M Shevchenko, D Shishin

This study represents a part of comprehensive research aimed at integrating nickel into a thermodynamic database constantly developed at Pyrosearch. The behaviour of Ni in calcium-ferrite slags is considered. An integrated approach combining experimental and thermodynamic modelling methods has been employed to predict phase equilibria in the NiO-CaO-FeO-Fe2O3 system under oxidising conditions and in equilibrium with the metal FeNi phase. The compositions of liquid slags and coexisting solid solutions have been determined through the analysis of equilibrated and quenched samples by electron probe microanalysis technique (EPMA). The research results are presented in the form of liquidus projections on the corresponding phase diagrams, considering both oxidising and reducing conditions. The solubility of Ni in spinel, dicalcium ferrite and calcium oxide as well as solubility of Fe and Ca in Ni monoxide, have been examined under several atmospheric conditions. Additionally, the compositions of the NiO-FeO monoxide in equilibrium with metal phase have been studied. The experimental data not only support the outcomes of thermodynamic modelling but also validate the parameters of the applied thermodynamic models, thus confirming the reliability and accuracy of the integrated approach.

Aug 21, 2024

By C D. Strickland

Western Australia (WA) has been a significant world producer of titanium minerals (rutile, ilmenite and leucoxene) and zircon for over 55 years. In 2010, despite global difficulties, WA accounted for 12 per cent of world production for zircon, ten per cent for ilmenite, and eight per cent for rutile. With downstream processing, titanium minerals (ilmenite, rutile, leucoxene) and zircon exports for 2010 were valued at $511 M (Department of Mines and Petroleum, 2010).Production is dominated by two areas of the Perth Basin, namely the Eneabba and the Bunbury-Capel regions, which are located 240 km north and 200 km south of Perth respectively. Mineralisation is within Cenozoic beach or near shore dune deposits at three broad altitudes related to the present coastline, and two older higher sea-level still-stands. The titanium-zircon minerals presumably were derived from the underlying Mesozoic sediments of the Perth Basin. Contrary to expectations, age dating suggests that the ultimate source of most of this mineralisation was not the adjacent Yilgarn Craton. With the cooperation of industry, the Geological Survey of Western Australia has mapped all known significant titanium-zircon mineralisation within the Perth Basin. This mapping has identified ‘strategic mineral resource protection areas’ that should be set aside for future mining, ‘sterilised’ and ‘mined’ areas that generally do not restrict land use options, and ‘possible strategic resource areas’ which have exploration potential for hosting titanium-zircon mineral deposits.The Perth Basin is currently undergoing rapid residential and industrial development. By informing all stakeholders of the locations of potential mining areas, the titanium-zircon mapping has the ability to reduce future land use conflicts, and facilitate sequential land use planning. Appropriate planning measures are being implemented to ensure that the Western Australia’s titanium-zircon minerals industry remains strong and viable in the future.

Oct 5, 2011

By D Morrison, P Goodman

The cycle time between adjacent stopes is critical to achieving the required production rate from 3500 Orebody; one of the Enterprise Mine orebodies. Current Mt Isa cemented fills require a 90-day cure period which had to be cut to 30 days while maintaining the required strength criteria. The Enterprise Mine Feasibility Study recommended that this be achieved by Cemented Slurry Rock Fill (CSRF), but that on-going research into paste fill be continued. The continuation of the research, in conjunction with overseas visits has recommended that the 3500 Orebody be filled with paste fill, with the potential to fill other orebodies. The paste fill will comprise cyclone and thickener dewatered copper tailings to which Portland Cement (PC) is added before vertical borehole delivery and undergound pipeline reticulation to individual stopes. The benefit is not only re-use of copper tailings but also much reduced binder usage.

Jan 1, 1998

By G Ferguson a, P Carrasco, P P. A Dowd

International codes of practice offer broad definitions with respect to the classification of resources in terms of risk. Specific guidelines and protocols, to analyse sample data, carry out geostatistical appraisals, develop geological models and finally estimate and classify resources, are not addressed. Neither are detailed requirements for engineering mineable reserves from estimated resources. In addition, international codes of practice fail to distinguish between types of deposit, other than in broad terms, as for example, The AusIMM JORC Code (JORC, 1999) which makes reference to diamond and coal deposits. The objective of this paper is therefore to set in motion the process of specifying detailed protocols, acceptable to the international community, for the assessment, reduction and management of risk associated with the development and extraction of mineral deposits. Ordinarily, the main risks and issues encountered during the process of estimating resources and subsequent conversion to reserves, encompass:failure to understand relevant geological controls of mineralisation; validation of grade interpolation; optimism in geotechnical appraisals of dilution and stability and the consequent selection of inappropriate mining methods; metallurgical modelling of minerals and contaminants reporting to concentrates; appraising the hydraulics of heap leaching and the numerous factors that can affect recovery; difficulty of managing metal price cycles and changes in regulations within the constraints of long-term mining plans; and development of better evaluation techniques for mining ventures. Uncertainty is inherent in estimation and engineering work, and its identification, reduction and management should be a fundamental goal of all involved in the mining industry (Figure 1). Variability may be reduced by:following internationally accepted practices for the collection, manipulation and analysis of geoscientific data; and verifying that the procedures actually performed meet the associated standards. Increasing amounts of data will also reduce uncertainty, but only if the procedures used to collect and appraise such data follow the relevant procedures. It is thus the aim of a series of papers in preparation, Beniscelli et al (in prep), to put forward detailed guidelines, for:project sponsors û to provide a global view of the work and documentation needed to support requests for funding various phases of project development and budget approvals; geologists û to indicate a checklist of the requirements and standards for the exploration and estimation of resources; and engineers and economic analysists û the protocols for characterising, modelling, engineering and evaluating the extraction of reserves. It is therefore hoped to encourage the development of consistent standards for declaring reserves within the mining industry. Data from projects and operations will be utilised to illustrate the benefits of adopting a rigorous approach to estimating resources and engineering reserves, Beniscelli et al (in prep).

Jan 1, 2000

By J Zhao, C E. Loo

The flame front is a narrow region in the iron ore sintering bed where coke particles combust. The maximum flame front temperature is as high as 1400°C. At high temperatures, the sinter mix components react to form melts, which facilitates material coalescence and the formation of dense sinter particles. It is well-established that flame front speed is an important factor influencing sinter productivity, sinter quality and fuel rate. In this work, the effect of suction, coke addition and mix moisture on flame front speed was studied in a pilot-scale sinter pot and also using the outputs of a recently developed theoretical model, which takes into account most of the significant physicochemical processes in sintering. Airflow through the bed has a large influence on flame front speed. A power law relationship between these two parameters means that increasing sintering airflow rate will lead to increased flame front speed, but the increases become smaller at higher airflow rates. Sinter pot test results showed that increasing coke addition decreased green bed permeability and increased flame front temperature, which resulted in increased flame front resistance and decreased flame front speed. Studies also showed that green bed properties are sensitive to sinter mix moisture level. The changes in green bed properties further influence the flame front speed and temperature.CITATION:Zhao, J and Loo, C E, 2015. Dependence of flame front speed on iron ore sintering conditions, in Proceedings Iron Ore 2015, pp 83–90 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By J-P Franzidis

Mill operators have traditionally been forced to rely on grade-recovery curves and overall flotation rate constants when analysing proposed improvements to plants. This has led to loss in money and time when a proposed change that showed potential in laboratory scale tests failed to show improvement in the plant. Frequently, this is a result of the operators being unable to gain insight into how and why the proposed change affected the flotation performance. This is due to the classical models not including any description of the subprocesses of flotation and their individual contribution to the overall flotation performance. A new flotation model has been developed as part of the AMIRA P9 project that separates the flotation process into subprocesses and includes the contribution of both the pulp phase and froth phase to the overall flotation recovery. It is not possible to determine the individual components of this new model on traditional pilot plants as they lack the required flexibility and scale. Therefore a new pilot plant has been developed known as the Floatability Characterisation Test Rig (FCTR) that has the flexibility and features required for the determination of the flotation subprocesses. The flexibility and features of the FCTR also make it an ideal tool for investigations into many different aspects of flotation research. These include the effect of reagents, grinding, and power on the flotation performance. This paper will describe the methodology for using the FCTR in these fields of research and highlights the advantages of using the FCTR over traditional methods.

Jan 1, 2000

By M Fuchs

Roadheaders were introduced to mining and tunnelling in the early-1960s. Since this period their main field of application has been for roadway drivages in coal mines and for mineral production, for instance in coal, rocksalt, potash and gypsum mines. Their main field of application in tunnelling is in softer and partly friable rock formations, a suitable area for non-blasting excavation. However, in longer tunnel sections excavators with high ripping forces have replaced roadheaders in many situations. The main arguments against roadheaders have been and still are:a sharp increase in excavation cost with increasing rock strength and increasing abrasivity; and greater risks in conditions which have not been, or could not be, investigated to a sufficient extent. These arguments have, to a great extent, restricted practical roadheader application in production mining and in a lot of æstandardÆ tunnel projects. To address these limitations, factors which could make roadheaders attractive for such conditions and could overcome existing technological difficulties have been investigated. Extension of the economic field of application in hard rock was found to be the most important and the most effective step forward.

Jan 1, 2002

A mining operation can be identified as demonstrating prudent management when a number of vital characteristics are evident.All risks and opportunities that are critical to the on-going success of the operation have been identified and are being effectively managed. All significant tasks and events are plan driven. All levels of management visibly support the policies of the operation through their attitude, behaviour and actions as well as words. Supporting evidence for required activity and the outcomes is readily available. Improvement mechanisms are working to advance the key business processes. Everyone is working towards satisfying the needs of the stakeholders of the operation. When these characteristics are integrated with the satisfaction of all legislative requirements, all industry codes and optionally all relevant international management system standards then an operation is fulfilling all the requirements of a Due Diligence Process. The majority of mining operations do not show all of these characteristics and therefore unnecessarily suffer from missed profit opportunity and constant cost pressure, less than acceptable safety and health and environmental performance and consequent poor relations with employees, unions and regulators. In these operations the characteristics to be observed are quite different.Serious incidents are occurring with no sign of a rate decrease. The operation lurches from one panic ituation to another. Management are absent in their leadership, but very active in developing rules and enforcement methodologies. The operation has no history. Re-inventing the wheel with employees who come and go at an alarming rate seems to be forever occurring. All efforts are directed at controlling the business outputs with a strong emphasis on blame. Everyone is trying to look busy to avoid the ever-present cost reduction threats. To change to more prudent management utilising a Due Diligence Process is not theoretically difficult. However it does take clear direction, focussed efforts, supporting actions with appropriate tools and perhaps most importantly an internal desire and drive to become such an operation. A Due Diligence Process is about doing the important things that have to be done, providing the understanding of why they are important, demonstrating proof of activity and effectiveness, and leading the way through effective management.

Jan 1, 1998

By C Mark

Coal bursts involve the sudden, violent ejection of coal or rock into the mine workings. They are a particular hazard because they typically occur without warning. During the past two years, three US coal miners were killed in two coal bursts, following a six-year period during which there were zero burst fatalities.This paper puts the US experience in the context of worldwide research into coal bursts. It focuses on two major longwall mining coalfields that have struggled with bursts for decades. The Utah experience displays many of the ‘classic’ burst characteristics, including deep cover, strong roof and floor rock, and a direct association between bursts and mining activity. In Colorado, the longwalls of the North Fork Valley (NFV) also work at great depth, but their roof and floor strengths are moderate, and most bursts have occurred during entry development or in headgates, bleeders or other outbye locations. The NFV bursts also are more likely to be associated with geologic structures and large magnitude seismic events. The paper closes with a brief discussion of how US longwalls have managed the burst risk.CITATION:Mark, C, 2014. Coal bursts in the deep longwall mines of the United States, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 33–40 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By J Jeffrey, G W. Wilson, L Gilbert, C

Prior to the commencement of mining, the acid rock drainage (ARD) potential of the waste rock to be produced by an open cut mining operation is assessed by a variety of techniques carried out on drill-hole samples. These include, among others, acid base accounting (ABA), net acid generation (NAG) testing, and kinetic testing. Based on the results obtained, a strategy for the identification, separation and selective placement of waste rock having different potentials to form ARD is developed. During the course of mining, the waste rock classification scheme will be re-assessed periodically to confirm that it is appropriate. This re-evaluation may result in a change in classification scheme, and waste rock dump samples may be obtained for ARD assay purposes to confirm the appropriateness of the revised scheme. The paper describes the evolution over time of the scheme used to classify waste rock at a major open pit gold operation in New South Wales, Australia, including the development of a hydrological model. To confirm the appropriateness of the revised scheme, ARD assay testing was carried out on drill-hole samples collected from dumps having different ARD potential designations, including Non-Acid Forming (NAF), Potentially Acid Forming (PAF), and Low Grade Ore stockpiles. The results of the ARD assay testing and water quality monitoring confirmed the appropriateness of the ARD potential designations and the revised classification scheme, which has been adopted.

Jan 1, 2003

By D A. Deglon

Solids suspension is important in the design and operation of mechanical flotation cells, and is a necessary precondition to particle collection. Most of the fundamental hydrodynamic research that incorporates some aspect of solids suspension was done by Arbiter, Harris, and co-workers, or Schubert and co-workers. However, a need for research into solids suspension in mechanical flotation cells exists, since very little has been done since the late 1980s; a time that also coincides with the advent of round mechanical flotation cells and the subsequent dramatic increases in maximum flotation cell sizes. In this work, concentration profiles and critical impeller speeds, Njs, were measured in a 0.124 m3, round cell fitted with a 0.150 m, Bateman impeller mechanism. Two solids size fractions (75 - 106 and 150 - 250 ¦m) were tested, in ungassed and gassed conditions (JG = 0, 1 cm/s) and at various impeller speeds (300 - 900 rpm). The effectiveness of solids suspension was quantified in three ways in terms of extent of off-bottom solids suspension, suspension height (extent of solids distribution), and variation within the solids distribution, which together present a complete quantitative picture of solids suspension and distribution within the cell. Consistent trends were found when these effectiveness criteria were considered against relative impeller speed, in terms of percentage of critical impeller speed, N/Njs. Off-bottom solids suspension is complete at or above 100 per cent of Njs, with significant sedimentation occurring as the impeller speed drops below 60 per cent of Njs. Suspension heights consistently reached a level equivalent to 90 per cent of the tank diameter at the critical impeller speed, and dropped off significantly as N/Njs dropped below 60 per cent. The variation in the solids concentrations within the sampled profiles showed consistent trends in two-phase but not under three-phase conditions. The paper concludes that the critical impeller speed, Njs, commonly used in the design and operation of standard stirred tanks, is a very useful solids suspension benchmark for describing all aspects of solids suspension in mechanical flotation cells and should be correlated to system conditions.

Jan 1, 2005

By D Giurco

As part of global systems of mineral production and consumption, the Australian minerals sector is facing sustainability challenges across technological, social, ecological, economic and governance domains, as well as between local, national and global scales. To ensure that the Australian minerals sector progresses towards sustainability, it is imperative to understand the possible ways in which AustraliaÆs mineral resources could support sustainable futures. A significant research gap exists between the complex nature of questions concerning minerals sustainability and the reductionist methods available to deal with them. This paper argues the need for broader, more integrated approaches to questions concerning minerals sustainability, which can address multiple human perspectives, complex and æmessyÆ patterns and processes across multiple organisational, temporal and geographical scales and whole systems of mineral production and consumption. To inform the development of a new approach to minerals sustainability, this work reviews the contemporary understanding of the Australian minerals sustainability problematic, from the perspective of the Australian minerals sector (Minerals Council of Australia), the Australian research sector (Mudd 2007a, 2007b; Mudd and Ward 2008) and a multi-scale international project (MMSD 2002). This review shows the focus of current responses to the minerals sustainability problematic, identifies the need for an integrated approach to questions of minerals sustainability and addresses how different approaches are informed by underlying and unarticulated assumptions about the tolerability of tradeoffs between different societal goals, the treatment of uncertainty and the application of different conceptual geographical, organisational, temporal and life cycle scales to define the minerals sustainability problematic. The Mineral Resources Landscape proposed, offers an expanded conceptualisation of minerals sustainability, to link minerals production and consumption in an integrated assessment across the entire minerals supply chain, connecting social, ecological, technological, economic and governance domains across local, national and global scales. The key leverage points governing change in the Mineral Resources Landscape are identified as: the material source, extraction and production technologies, level of service and value, and consumption patterns. Mapping the key challenges facing the minerals sector, as identified in the review herein, indicates that the boundaries defining traditional conceptualisations of minerals sustainability focus on the material source and technology and ignore two very key drivers of the Mineral Resources Landscape û the æservicesÆ minerals offer to society and the æconsumption trendsÆ which assimilate these services into society. Understanding these overlooked aspects of the Mineral Resources Landscape, along with the conventional areas of focus, is essential for identifying the Australian minerals sector as a provider of sustainable mineral services. This insight prompts a reconsideration of the role of minerals services and consumption trends, together with the role of the material source and technology in shaping change and the emergence of sustainable systems of Australian minerals production and consumption, across multiple scales and domains.

Jan 1, 2009

By G Nicholas, S Coward, J Vann, R Wolff, S Jackson, S Moayer, A Bye

"A new approach to mineral project evaluation is described called Scenario-Based Project Evaluation (SBPE). SBPE incorporates well established æscenario planningÆ and æscenario thinkingÆ approaches, which are used extensively in other industries,?most notably the?petroleum industry. While most scenario planning is qualitative and non-probabilistic, the approach described here includes both quantitative and qualitative aspects. SBPE is complementary to optimisation approaches and allows mining firms to build and operate projects that are more robust in the face of adverse changes as well as proactively respond and exploit the upside offered by a realistic assessment of variability. The approach has potential to improve project performance and decrease operational risk. It also has important applications for currently operating mines.Conventional evaluation of metalliferous mineral deposits uses estimates of metal grades and deleterious attributes in singular æorebody modelsÆ, usually 3D block models, which fail to capture two critical aspects that underpin the realised value of mining projects: the inherent uncertainty of the estimated attributes the spatial variability of attributes, at the scale of mining selection, which impact on downstream processing steps and fundamentally drive realised value. While singular models are appropriate for estimating block averages, conditional simulation (CS) models of the relevant attributes are needed to represent uncertainty and capture spatial variability. Any attributes that can be either built into CS models and/or modelled in the envisaged mining/processing steps, can be evaluated fully through to highly ægranularÆ (ie detailed and un-smoothed) cash flows. A complete view of SBPE relies on selected strategies being tested against plausible æscenariosÆ of factors external to the project and thus outside management control. æExternalitiesÆ captured in such scenarios include market prices, costs and taxes. Via SBPE, project managers may demonstrate that there is material value in preserving or purchasing options that provide future flexibility to respond to the changing externalities or changes in orebody performance. Such flexibility generally comes at a cost but is very difficult to value. It is argued that full value chain evaluation using SBPE can help to value these options for a mining company. A case study for a gold mine is presented.CITATION:Vann, J, Jackson, S, Bye, A, Coward, S, Moayer, S, Nicholas, G and Wolff, R, 2012. Scenario thinking - A powerful tool for strategic planning and evaluation of mining projects and operations, in Proceedings Project Evaluation 2012, pp 5-14 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

May 24, 2012

By P Minkkinen

"Pierre Gy showed in his early works that the results in estimating the variance of the mean value of continuous lots depends on sampling mode (random, stratified or systematic), except in the theoretical case that the measurand is randomly distributed in the lot. The experimental variance estimate calculated from samples taken from the lot is independent of sampling mode but depends on sample size and the type of the lot heterogeneity. Variography can be used to estimate the variance of the lot mean for different sampling modes.Gy also defined weighting error, which is made if a simple average is calculated from the assays of samples taken from a continuous object (eg from a process stream) where the flow rate varies with time and is correlated with the concentration of the analyte in the stream.The effect on sampling uncertainty of the three sampling modes and their interaction with the following factors in estimating the uncertainty of the mean concentration is studied using simulated lots, and lots having heterogeneity patterns similar to those of real data sets, including the effect of: the type of heterogeneity (random, grading and clustered heterogeneity patterns) increment size and number employing composite sampling weighting error. CITATION:Minkkinen, P, 2017. Dependence of the variance of lot average on the sampling mode and heterogeneity type of the lot, in Proceedings Eighth World Conference on Sampling and Blending, pp 319–330 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

May 9, 2017

By Armstrong A

Queensland is Australia's second largest mining state with world-class deposits of coal, base metals, bauxite and magnesite. The total value of Queensland's mining production is about $5 billion per annum, and coal accounts for around 55 per cent of that total. The environmental issues which arise as part of management and regulation of the industry are resolved within the EMOS process. The Environmental Management Overview Strategy is the cornerstone of the policy 'Environmental Management for Mining in Queensland' developed jointly by the Queensland Department of Minerals and Energy and the mining industry. The Gordonstone Coal Mine is the largest underground mine to gain approval under the new policy. Accordingly, Gordonstone has a well planned environmental management program which takes into account site-specific factors and provides for continuous compliance with the provisions of the Mineral Resources Act in a self-regulatory context.

Jan 1, 1994