Search Documents

By E Kunz

Decreasing the gas content in the worked seam by degassing before the start of winning has proven its worth in some areas of German hard coal mines. On the one hand, it removes the risk of gas/coal outbursts and on the other hand it reduces the gas inflow into the longwall. The underground experiences of the last 30 years have led to a æhit listÆ of coal seams with respect to their suitability to predegassing. Trials in the DMT laboratory and also results gained in the deposit show that the suitability of a seam for predegassing depends on its rank. In seams with volatile matter of 20 - 30 per cent, high efficiency ratings are achieved as a rule, with lower ratings both in seams with lower and with higher content of volatile matter.If the rock pressure is unusually high, the efficiency rating of the predegassing is lower, even in seams which would normally be suitable for this process. Under unfavourable conditions, for example below or above residual pillars, in-seam boreholes cannot be drilled successfully and the method is not practical. But if the worked seam was already stress relieved, the predegassing has an optimal efficiency. Latest investigations show that the distance between the in-seam boreholes can be extended. But in that case, the time necessary to reach the same reduction of the gas content increases considerably.

Jan 1, 2005

By J P. Moodie

Recent trends in flotation technology are briefly reviewed. These show that considerable development has been made as the operators, suppliers and technologists have responded to the challenges of the industry. Most of these advances have been based on empirical and phenomenological methods. There is a considerable opportunity to make further advances through a more fundamental, scientific approach. Some of this work is discussed and, although progress is being made on this front, industrial uptake has been somewhat slow. A number of specific issues facing the industry are discussed.

Jan 1, 2005

By X Yang

White phosphorus (P4) is a critical element in industry, but its current production from phosphate rock using the carbothermal reduction method raises significant environmental and health concerns. This pressing issue necessitates the development of new technologies that facilitate the sustainable production of P4. In response, my team is actively developing an innovative, coke-free approach for white phosphorus production. This method involves the dissolution of phosphate rock in molten CaCl2, followed by the extraction of P4 through electrochemistry at relatively low temperatures. Moreover, this approach has the potential to utilise phosphate-bearing solid wastes as raw materials, further enhancing its environmental benefits. By employing this cutting-edge technique, we aim to revolutionise the phosphorus chemical industry towards greener and more sustainable practices. This paper provides evidence of the feasibility and effectiveness of our proposed approach.

Aug 21, 2024

By H M. A Ilyas, M Yahyaei, S Amari, M Darestani

Tailings are generally deposited on or near to the mine sites, occupying the site area, and being an economic burden for mining companies. Tailings can cause several environmental impacts, such as leaking toxic substances and contaminating underground water, emitting greenhouse gases, and damaging natural bodies and wildlife. Geopolymerisation of mine waste effectively transforms mine waste into more valuable, environmentally friendly products. Geopolymers are inorganic aluminosilicate materials that are widely applied in the construction industry (Araya, Kraslawski and Cisternas, 2020). The high performance and the low-CO2 emission of geopolymers make this type of material potentially more desirable than ordinary cement, given that manufacturing one ton of traditional cement generates approximately 0.8 tons of CO2. This process is seen as a promising method for repurposing tailings and reducing the environmental impact of mining waste. However, the environmental impact of geopolymer production is not sufficiently comprehended (Mazzinghy et al, 2022). Moreover, geopolymerisation of mine waste can offer several economic benefits, including reduced waste management costs (Amari et al, 2019; He et al, 2022), reduced raw material costs, and potentially lower production costs. However, there are several challenges that need to be addressed to ensure the economic feasibility of the process. This study aims to demonstrate the potential environmental impacts of geopolymer concrete produced using mine wastes and industrial by-products such as blast furnace slag (BFS). For this, a comparative cradle-to-gate life cycle assessment (LCA) methodology was conducted on different geopolymer mix designs, and the greenhouse gas (GHG) emissions results were compared to the ordinary cement. LCA can be used to evaluate the environmental impact of geopolymerisation of mine wastes in various ways. One important impact category is GHG gas emissions, which contribute to climate change and is the focus of this study. Another aim of this study is to evaluate the economic feasibility of the geopolymerisation of mine wastes via economic analysis (EA) to identify the key economic factors and trade-offs associated with repurposing mine wastes through geopolymerisation.

Aug 2, 2023

By A C. Robertson

Over the past decade there has been continual change in the way that mines have been managed and the component roles of those people who make up the total mine management system. Major issues have included the change in the business structure of mining companies, the change in on-site infrastructure, increased personal liability of managers for the safety and health of employees and increasing social and environmental pressures on managers and their staff. This paper looks at the changing roles of two of the many groups of professionals associated with the mining industry - the equipment supplier and the mining consultant. The profiles of the ACME Group Pty Ltd, suppliers of ventilation equipment and ancillary canvas and plastic products to the mining and construction industry, and Tennent, Isokangas Pty Ltd, Consulting Mining Engineers, are presented.

Jan 1, 1998

By S N. Nyoni, K C. Corin, C T. O’Connor

Considering future water scenarios, as influenced by the increasing scarcity of water and the move towards sustainable process engineering etc, the closed water circuit becomes an important point of study in metallurgical operations, such as in milling and flotation. However, a deterrent in the use of recycled process water is often a lack of understanding of the effects of the accumulation of dissolved ions and other process chemicals. Recovery of the valuable minerals may be impacted by the concomitant complex mineral-pulp chemistry interactions. Literature indicates that these interactions are not necessarily antagonistic to process outcomes. Wet milling using steel media results in the dissolution of Fe from the media, the rate of which is dependent, inter alia, on the type of media and the chemical conditions of the aqueous environment in the mill. The pulp-phase interactions of dissolved ions with sulfide minerals may result in significant changes to the chemical conditions in the mill, which may subsequently impact negatively on the flotation recoveries. To understand the effect of these interactions in the context of the processing of sulfide minerals, this study seeks to consider the effect of three factors, viz mineral type – pyrite (Py) and galena (Gn) -, milling media of different compositions – forged steel (FS), 21 per cent high chrome and ceramic media -, and water chemistry, viz, deionised water (DI) and synthetic plant water (SPW). Ceramic media and galena are used for the respective control cases where the milling media and sulfide mineral contribute no Fe species. Using DI as a control case, a high ionic strength case is used to mimic the changes in water chemistry for a closed water circuit. Batch flotation tests are used as a diagnostic tool to determine the effects of these media-water-mineral interactions to investigate correlations between the chemical reactions occurring and chemical species present during the milling process and the ultimate flotation performance.

Aug 24, 2022

By C Xu, B Li

Multi-sensor fusion visual perception technology significantly enhances visual perception capabilities in complex and harsh environments by combining visual data from different sensors. This technology is especially useful for scenarios where traditional single visible light sensors, such as standard cameras, struggle due to poor lighting, adverse visual conditions, or other visual obstructions. In environments with low light, smoke, or dust, the performance of conventional visible light sensors degrades, limiting their application. By integrating data from various sensors like radar, infrared thermal imaging, and others, multi-sensor fusion technology provides a more comprehensive and complementary visual solution. This fusion not only enhances the robustness of visual systems but also greatly expands their potential applications in fields like visual surveillance. In recent years, deep learning methods have become the mainstream technology for addressing multi-sensor fusion issues, demonstrating significant advantages in adaptive feature selection compared to traditional machine learning methods. However, deep learning-based multi-sensor fusion algorithms still face several challenges. The design of network structures is often redundant, lacking effective screening of useful components within multimodal information. Mainstream fusion algorithms focus excessively on improving display effects without adequately considering the needs of downstream applications and tasks. Existing fusion perception algorithms are generally designed for open visual scenes and lack targeted design for complex visual degradation factors present in tunnel environments of mines. Current deep learning methods for designing multi-sensor fusion networks heavily rely on manual experience to create fusion modules. This reliance increases the complexity of network design and can lead to redundancy. Redundant network modules are difficult to identify in end-to-end learning tasks at this stage, significantly slowing down network inference and potentially interfering with the output of fusion perception. Additionally, training these fusion modules typically requires large amounts of well-annotated multimodal data, further increasing implementation difficulty and cost. For instance, the fusion network design proposed by Li and Wu (2018) focuses on extracting multimodal fusion features, while Zhao et al (2020) introduced a feature decomposition mechanism in the feature fusion and extraction modules. Researchers like Zhang and Ma (2021), Xu et al (2020), and Liu et al (2017) have attempted to improve network structures through dense cascades and the introduction of residual connections. Although these methods have improved the handling of multimodal information to some extent, they still face limitations in distinguishing between useful and redundant information, with redundancy persisting in network designs. Ideally, the design of fusion networks should be more intelligent, guiding network structure design heuristically based on the importance of different modal information for the current task. This would reduce information redundancy and network weights, requiring the development of new algorithms or frameworks capable of automatically identifying and optimising fusion strategies, thereby reducing dependence on manual experience while improving fusion efficiency and network performance. Current deep learning designs for multi-sensor fusion algorithms often overlook the

Sep 1, 2024

By J Hunt

A critical aspect of geometallurgy is quantifying mineralogical and textural relationships that affect mineral processing (eg, liberation and recovery). However, to date, this has been an expensive and time consuming venture and only minimal amounts of this type of data are typically available to be included in the mine planning process. Our research is focused on developing methods that will produce the required mineralogical and textural data rapidly and inexpensively. New methods of characterising liberation potential from image analysis of coarse particulate material and direct small-scale flotation measurement are compared with measurement of liberation at final grind size (ie conventional tests on MLA). The new tests are designed to rank the liberation potential of samples in order to classify an ore deposit into domains of low, medium and high liberation potential. This parameter can then be used to adjust the cutoff used to differentiate ore from waste. Results to date show that all tests provide the same ranking for the samples. The measurement based on coarse particulate material compares favourably to the results from MLA analyses on the same samples. Further work is being carried out to determine which of the tests will be the most effective in terms of time, effort and cost

Sep 5, 2011

By C Zhang, G Si, J Oh, X Zhu

The presence of rock joints has a huge impact on the strength, deformability, and permeability of fractured rock masses by providing surfaces of weakness on which further deformation are more prone to occur, and by serving as the major channels of water flow due to low matrix permeability. In earlier studies, water flow-through rock joints is often assumed as laminar flow between two ideal smooth parallel plates, and the well-known cubic law was derived and widely used to characterise the hydraulic behaviour of rock joints. However, natural rock fractures are irregular and of spatially varied aperture. Thus, the concept of equivalent hydraulic aperture was introduced to modify the cubic law. Numerous works have been conducted on the relation between hydraulic aperture and mechanical aperture incorporating various geometrical parameters. The surface roughness is one of the most sensitive factors for water flow-through rock joints. The aperture distributions are irregular in natural roughed fractures relative to the parallel plates. Barton et al (1985) and Olsson and Barton (2001) incorporated the joint roughness coefficient JRC in evaluating hydraulic aperture and proposed an empirical equation based on fluid flow tests. However, their equations do not conform to the dimensional consistency. Many other researchers (Zimmerman and Bodvarsson, 1996; Xiong et al, 2011; Li et al, 2019) considered aperture distributions in their equations. But the aperture distributions change during shear was always neglected. The contact of rock joints also has a significant impact on the hydro-mechanical behaviour of rock joint, since fluid tends to flow-through a rough joint along connected channels while bypassing the contact obstacles with tortuosity. Nonetheless, previous research mostly considered joint roughness or aperture changes based on 2D joint profiles, while the contact and tortuosity based on 3D surfaces were often overlooked. Only a few works have been made on quantifying the effect of contact area on flow behaviour (Walsh, 1981; Zimmerman et al, 1992; Zimmerman and Bodvarsson, 1996; Yeo, 2001), and mostly ignored contact area change induced by shearing and the associated impact on flow behaviour. Summarily, the quantification of fracture geometry effects on water flow in single rock joints still needs further investigation, especially when considering coupled shear-flow processes. This paper, therefore, aims to study the impacts of contact area and aperture distributions of the single rock joint on the flow behaviour. The evolutions of contact area and aperture distributions induced by shear are considered. Then, an improved model for estimating the hydraulic aperture with the mechanical aperture incorporating the above factors is developed. Finally, a series of shear and shear-flow tests are conducted on artificial joint samples and the model performance is verified by comparing against the results of experimental tests.

Nov 29, 2022

An experienced drill operator is able to make a log of a drill hole defining physical properties of the earth such as hardness or structure as they vary with depth. This log is based on intuition or how the drill æfeelsÆ. Rock characterisation using measure while drilling (MWD) parameters aims at refining this intuition into a package that accurately defines the properties of the subsurface as the drill bit propagates. Subsurface investigation using MWD parameters aims to combine physical drill parameters: Pull down force, rotary speed, penetration rate, torque and vibration in such a way to yield real time rock properties. MWD is investigation in its most primitive form, put simply MWD is merely a physical probe æfeelingÆ what the rock mass is at depth.

Jan 1, 2001

One of the problems with mining projects is the setting of the design criteria that will best match the requirements. Normally this is expressed in economic terms but can be other factors. With massive orebodies these problems are often compounded by the general lack of distinct mining boundaries. A technique using evaluation surfaces was developed at Palabora for the underground mine design. This technique has subsequently been applied on several other mining projects to assist in the determination of the design criteria. This paper discusses the method, illustrated by some of the results of these studies.

Jan 1, 2000

Safety bulletins and stickers issued for the paste backfill plant at Cannington read as follows: æCannington Paste Fill Plant, First of ItÆs Kind in AustraliaÆ. We could even dare to state that the Cannington plant is different than any other paste backfill plant in the world because of the overall design, plant equipment and underground delivery. However, one thing to be certain of is, the paste backfill plant works as designed and a pump is not required to deliver paste underground given the general plant arrangement at Cannington. The past two years have been a process of evolution to design and construct the plant and make it work. This paper will describe the paste process using full mill tails along with placement of cemented paste underground. Discussions will include rationale of fixed plant selection along with various control requirements. BHP World Minerals recently commissioned its paste backfill plant in December 1997. Cannington is placing full mill tails underground via two surface boreholes that deliver either to primary or secondary stopes.

Jan 1, 1998

By B Tessier

Checking the quality of a blast may be considered as subjective. Checking this quality will require measuring objective parameters. One of them is the resulting fragmentation of the blasted product. Numerous fragmentation æmeasuringÆ systems have been developed and marketed, based on image-processing. This presentation of FragScan will illustrate advantages and difficulties when using such a system. FragScan is essentially defending a policy of large and representative sampling. The purpose is to show how fragmentation is discriminating both productivity and profit of quarry operations on a blast-by blast basis. The next step will then be to ædriveÆ the blasting process to reach a æbetterÆ fragmentation. Other applications require the fragmentation as an essential result: this is the case for large boulders used in structure-reinforcement. Several case-studies have shown that FragScan can be used for quality-control, checking size-distribution of the product according to the requirements of the end-user. Only clear thinking about the precise use of such a æmeasurementÆ will further the success of this task.

Jan 1, 2001

By J Safarian, M K. Kar

Bauxite residue is one of the most important by-products from the alumina industry with no commercial use till now. The utilisation of bauxite residue through pelletising with different lime additions, hydrogen reduction, and smelting has been studied in this work. Three different types of green pellets were made with varying calcite-to-bauxite residue ratio and subsequently sintered at elevated temperatures. The sintered pellets were isothermally reduced at 1000°C under hydrogen gas followed by smelting of the reduced pellets in argon at 1500°C. Smelting of the reduced pellets leads to the recovery of metallic iron and the formation of a leachable calcium aluminate slag. X-ray diffraction (XRD) and scanning electron microscope (SEM) were used to characterise the phases and microstructural analysis. The iron produced in the smelting process has a high purity, above 99.5 wt per cent. While the iron content of the slags is quite low, and the slags shows variations of krotite (CaAl2O4), gehlenite (Ca2Al2SiO7), and perovskite (CaTiO3) phases based on the variation of calcite addition. It was found that the more calcite addition in pelletising yields higher percentage of krotite phase as compared to lower calcite-containing pellets. Employing quantitative XRD analysis, the krotite phase fraction was found approximately 85 wt per cent for higher calcite-added pellet, and around 74 wt per cent for lower calcite-added pellet. FactSage™, ver 8.1 (Thermfact and GGTTechnologies) thermodynamic software was used to evaluate the obtained experimental data, they both revealed that the

Jun 19, 2024

Transport Canada (Federal Government) constructed the Halifax International Airport (HIA) near Halifax, Nova Scotia, Canada in the late-1950s. Site location criteria were primarily; direct access to the city and a raised flat topography. Unfortunately, the site chosen was located on shallow Meguma group pyritic slate bedrock. In 1982, during the construction of an airport taxiway, it became very apparent that acidic run-off from excavated bedrock at the site was having a negative impact on adjacent aquatic habitat. The ensuing 20 years involved many efforts to rectify the acidic drainage problem with mixed results. Some of the techniques which have been implemented at HIA to address the acid rock drainage (ARD) issue include: dry covers, wet covers, wetlands, electrochemical treatment, open limestone channels, limestone gravel polishing beds, agricultural limestone application, and two hydrated lime [Ca(OH)2] addition treatment plants, the first producing low density sludge and the new one that creates high-density sludge. Based on over 20 years of water quality monitoring data it is apparent that only certain acid drainage mitigation methods have been effective at HIA. In 2000 when the Halifax International Airport Authority (the Authority) took control of the operation and management of the airport, including the ARD issue, it was decided to construct a modern, highdensity sludge, hydrated lime treatment system. This new $CAN 7 million system is now in operation and is achieving compliance with water quality guidelines. Due to high operating cost, a review of methods to optimise the system is being carried out. The HIA ARD problem, though minor by comparison to most mine sites, has provided unique challenges and may provide valuable insights into this urgent environmental and financial issue.

Jan 1, 2003

By Harper F

This paper outlines the authors' views of the methodologies which can be employed to value mineral properties at different stages of development for the purposes of project financing, mergers and public floats. This paper discusses the key issues in Discounted Cash Flow (DCF) analysis including the importance of data verification and the shortcomings in DCF analysis. Stockmarket valuation measures and valuation methodology for exploration and pre development projects are examined through examples and pitfalls are identified. The use of valuations in corporate transactions and their strategic value is also discussed.

Jan 1, 1994

By J Hadjigeorgiou

The stability of open stopes in underground hard rock mines is influenced by several factors including the shape and size of the excavation, surrounding stresses as well as the degree of jointing. This paper presents a design methodology for stope analysis in jointed rock masses. The proposed approach relies on geological structural data to construct realistic three-dimensional joint network models. The stability of an open stope is determined based on a limit equilibrium analysis.

Jan 1, 2000

By D Cliff

"It has been 17 years since the mine disaster at Moura No 2 Mine in Queensland. Recent disasters in the USA and New Zealand prompt the question what has changed since 1994. This paper att emptsto answer this question and identify areas that need improvement."

Jun 1, 2012

By M Grigorescu, J H. Hodgkinson

The expansive, open cut iron-ore mines in Western Australia typically experience few days of rain per annum, often amounting to less than 250 mm. Unlike mines where rainfall is frequent, they may be less prepared for extreme rainfall events. Such events can cause erosion, flooding and sedimentation, drainage alteration, spoil and stock heaps wetting and effect slope stability. Such impacts may threaten personnel safety, infrastructure, and production. The CRATER (‘Climate Related Adaptation from Terrain Evaluation Results’) framework collates and interprets a mine’s pre-existing data and semi-quantitative information to assess vulnerability to, and ultimately plan to avoid or minimise, flood-related hazard to infrastructure, people, downtime, environment and revenue. Outputs assist decision makers to design investment strategies for minimising mining operations’ vulnerability to climate. Previously developed for smaller, wetter mines in Queensland’s coal region, the outputs provide a hot-spot map, fault tree analysis and an assessment of the mine’s capacity to adapt. The multicriteria evaluation (MCE) within a geographic information system (GIS), equally suits iron-ore mines’ siteconditions (elevation, slope, drainage, soil and vegetation) to identify critical inundation areas. Hotspot results provide target zones for in-depth fault-tree analysis that, in turn, present a range of sitespecific adaptation options. Rainfall-intensity and the number of rain days since the 1970s have increased over central and eastern parts of the Pilbara Region. While tropical cyclones may become less frequent, they are projected to increase in intensity. Although some parts of the Hamersley Ranges receive more than 500 mm per annum, rainfall in the Pilbara is generally very low. Therefore, experience of the impacts of extreme rainfall events in the constantly changing topography of Western Australia’s iron ore region may be sparse. Minimising potential effects can be proactively assisted using CRATER.

Nov 8, 2021

By B Maybee

In underground mine planning, many potentially value-eroding decisions are made due to a lack of time and proper evaluation practices. The information required for mine planning decisions goes beyond external sources of uncertainty that are recognised by typical evaluation techniques used in the mining industry, to include technical factors (eg mine development layout) and the ability of a mineral extraction project to achieve its anticipated production levels. Due to the individual characteristics that define underground mining projects, each will exhibit a different risk profile, and thus advanced optimisation and evaluation techniques are required to capture this information.As underground mine planning tools become more sophisticated, mine planners have the capacity to investigate numerous mine sequencing options to identify the best strategy for a given project, creating higher value for shareholders. This paper describes a risk-based evaluation methodology (RbEM) that accounts for financial and technical risk in the evaluation of underground mining projects. While the use of the RbEM has been described in previous works, no benchmarking of the benefits that can be realised from a change in those decisions that are made early in the process has been undertaken. To show the benefits that can be achieved from using the RbEM, this paper updates a case study to which the RbEM was applied, and takes a retrospective look at whether additional value would have been gained by following the strategic recommendation of the RbEM versus a typical optimisation exercise that aims to maximise the net present value.CITATION:Maybee, B, 2012. Can a risk-based evaluation provide a more valuable mine design?, in Proceedings Project Evaluation 2012 , pp 53-58 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012