Search Documents

By P R. G Milne

A risk-based approach to optimising pit wall slope angles was trialled in the design of a 60m deep open pit in extremely weathered and distinctly weathered materials in the Kalgoorlie area. The pit used for this approach was Stage 1 of a three-stage open pit project. The Stage 3 pit will require long term stability, as it will contain the portal for a long life underground project. Information from failures induced by steeper wall angles used in the Stage 1 pit would be valuable in predicting and preventing long-term stability issues in Stage 3. In this approach, the pit wall slopes are based not on the normal factors of safety, but on the assessment of the probability of failure and the direct and indirect costs of dealing with the failure when it occurs. In this example, the benefits and risks of adopting steeper wall angles were compared in a series of graphs. These charted the increasing probability of failure and simultaneous decreasing factors of safety with increasing pit wall slope, and the range in the possible volumes of circular failures for increasing wall angles. These were brought together in a graph showing the potential excavation savings (in BCM) and the probable cost of a failure (probability of failure times the probable volume of the failure). The resulting pit design was based on the project Mining EngineerÆs semi-quantitative assessment of where and when a higher risk of failure was acceptable and where it was not acceptable as it may have unduly affected the integrity of haul roads or production. The design incorporated wider than normal berm widths to accommodate anticipated failures and to enable modification of the wall configuration if required. Several re-designs were required during the life of the project in response to aggressively induced failures. It is considered that this risk-based approach provides a practical route to optimal pit design and operation but it requires an experienced, dedicated and efficient mining team for it to be implemented with benefit.

Jan 1, 2003

A novel solvent extraction process, called the SOHNEX process, has been developed at the University of Utah. In this process, the organic and the aqueous phases flow countercurrently in a horizontal vessel, and the emulsion between the two liquid phases is generated by high-velocity gas jets injected at the bottom. The gas jets are located at certain intervals along the bottom of the vessel with phase disengagement zones on either side of the plume zone created by the gas jet. The system is simple, having no mechanical moving parts or complex internal structures, and yet provides good contact between the phases with minimal backmixing. Tests have shown that emulsions with a wide range of specific interfacial area, including that typically encountered in mixer-settlers, can be generated in this process. It has significant built-in flexibility of operation including the control of the flowrate and hold-up of each liquid phase. The SOHNEX process overcomes the difficulties in the operation of conventional solvent extraction equipment such as mixer-settlers and column extractors. A major advantage of the SOHNEX process is that the energy of mixing can be closely controlled by adjusting the strength of the gas jet. This allows an optimal control of the drop-size distribution of the dispersed phase and thus the specific interfacial area. The process is continuous, and any number of extraction and separation stages may be built into a single vessel. The gas can be recirculated in a closed loop, thus eliminating solvent loss and mist problems, especially for high-temperature operations. The SOHNEX problem can handle solutions that contain suspended solids and that form third phases. The simplicity of the equipment and operation with low maintenance will mean much reduced capital and operating costs as well as low environmental risks and improved safety. The SOHNEX process has been tested for continuous copper extraction from a dilute solution. Calculations also showed that uranium and other radioactive elements can readily be extracted in a small unit of the SOHNEX extractor while satisfying the nuclear criticality condition.

Jan 1, 2000

Solid EnergyÆs project evaluation process utilises a standard staged gate approach, with five levels leading ultimately to project execution (level 6). For a project to progress through each level, specific financial criteria need to be satisfied. Solid Energy primarily use value based (discounted cash flow) metrics to support investment decisions. Within this approach Solid Energy utilise a number risk-based techniques to quantify project uncertainty. This includes the use of risk-based probabilistic analysis using Monte Carlo simulation and probability-based scenario analysis. Figure 1 shows the net present value (NPV) cumulative probability. Project risks are identified through comprehensive risk workshops. The output of these workshops (list of key risks, ranges of uncertainty and probability of occurrence), is quantified within the financial models. Incorporating this risk information on a probabilistic basis allows an investment decision to be made with a robust knowledge of the range of possible project outcomes along with the likelihood (probability) of those outcomes occurring, for example 80 per cent confidence that the project value will be greater than NZ$10 M, 50 per cent confident it will be greater than NZ$50 M and ten per cent confident it will be greater than NZ$70 M. Incorporating risk implicitly into the financial analysis allows the business to easily evaluate/measure projects with different risk profiles. The detailed risk analysis does away with the complexity of arbitrary risk-based hurdle (discount) rates, as projects can be evaluated based on their specific risk characteristics. Whether a project will progress to the next level of investment and ultimately into implementation depends firstly on the value assessment in comparison with the associated risk/uncertainty, and secondly matching this with the businesses appetite for risk. At Solid Energy standard criteria are used for specific project evaluations, but in addition projects are considered on a portfolio or strategic basis also. Solid Energy attempts to maintain a mix of low risk (low value) projects with some high risk (high value) opportunities. The mix of projects must remain in line with the shareholdersÆ risk appetite. One of the keys to a successful investment decision is ensuring that the appropriate information is available to decision-makers so that they may proceed with a comprehensive understanding of the risks and impacts associated with the decision.

Jan 1, 2007

By A Xenidis, N Papassiopi, I Paspaliari

Acid generating sulfidic tailings covering a surface area of approximately ten hectares have been deposited in the historic mining area of Lavrion in Greece. For the development of a remediation strategy, the performance of three alternative acid generation control techniques was assessed under actual field conditions. The techniques involved the application of dry covers, including a synthetic HDPE liner and a compacted clay layer with capillary barriers. Furthermore, the potential formation of a low permeability hardpan layer at the sulfidic tailings surface by limestone addition was investigated. The field tests covered an area of 2500 m2, which was divided in equal quadrants, corresponding to the control plot and the three alternative remedial options. To monitor the amount and quality of percolated water, lysimeters were installed beneath the four plot areas. Based on the monitoring results over a period of six years, due to the dry climate encountered in the Lavrion area, a low amount of water percolates through the pyrites if no action is taken (control area), corresponding to 20 - 25 mm per year. This water is highly acidic, pH = 1.2, and contains a heavy load of contaminants, eg Fe 40 g/L, Zn 15 g/L, and As 1.5 g/L. The HDPE cover eliminated the percolation of water into the material for a period of five years, whereas thereafter the volume of leachates increased to values similar to those recorded in the control plot. The water collected in the lysimeter of the clay cover has been minimal corresponding to approximately five per cent of the drainage volume produced in the control area. In the fourth plot, which involved limestone addition to sulfidic tailings, the volume of drainage initially collected was almost double compared to the control area. After three years of monitoring, significant reduction in the amount of percolated water was observed, attributed to the formation of a cemented layer (hardpan), at a depth of 40-80 cm from the testpad surface.

Jan 1, 2003

By D La Rosa, W Valery, A Jankovic, S Ese

Metso Minerals Process Technology Asia-Pacific (MMPT-AP) has been working with many mining companies worldwide performing æMine to MillÆ or Process Integration and Optimisation (PIO) studies. MMPT-AP has developed a proven methodology to improve the efficiency of the mine-mill interface and gain maximum benefit. The PIO methodology involves rock characterisation, mathematical modelling and simulation to generate a list of operational and control changes for both the mine and concentrator. Following the methodology, the list of recommendations is developed relatively easily; the more challenging part depends on the company. Success of a PIO project relies on the ability of an organisation to implement change û both operationally and culturally: the human element. When a PIO project is started, there is initial interest and commitment from the company. But how can this be maintained? How does an operation know if the benefit continues? MMPT-AP is now developing long-term relationships with clients to ensure that the increased production and improved efficiency continues. Direct and indirect measurements are used to determine the key factors involved and to understand the cause/effect relationships. Simulation tools also can be used to compare current with recommended practices û so when material properties vary over time, the benefits can still be quantified. PIO is about empowerment: by measuring and understanding what parameters affect concentrator performance, the site personnel now have the knowledge to make a difference. Rather than simply reporting variable or poor concentrator performance, operations can predict when production will be affected and put controls in place to prevent it from happening. This requires support and commitment from the company or æbuy inÆ. Ensuring this buy in continues is the challenge facing every company involved in PIO work û but the benefits are well worth it. This paper will review MMPT-APÆs experiences in implementing PIO projects in the long term: from both the consulting and operational viewpoints. MMPT-APÆs involvement with a number of companies will be discussed as examples of what works and what does not.

Jan 1, 2007

This paper examines the broader implications of recent and ongoing changes in mineral resource managementå and reporting practices and the impact that these might have on mining companies. It is likely that an International Reporting Code will be developed in the near future, based on a number of National codes produced in recent years. However, this is only part of the reporting story, as an International Code brings with it a range of further issues to resolve. For the Code to be effective, there needs to be international recognition and perhaps licensing of Competent Persons and an expanded base of sponsoring professional bodies. Also, in an increasingly global business, shareholders, regulators and other interested parties need to know and understand the general processes involved in resource and reserve estimation and reporting in order to recognise companies that maintain the highest standards. There is a current trend towards greater scrutiny of company performance in a range of areas under the banner of corporate governance, and many changes are happening that will place greater disclosure burdens on all companies in the future. Good corporate governance means management of company assets for the benefit of the stakeholders. For a mining company, there is no greater asset than its mineral resources and reserves and directors are just as responsible for effective management of their mineral resources as they are for financial good practice. The paper looks at the relevance of corporate governance principles to mineral resource management and the changes that this could bring to the way that companies deal with regulators, shareholders, financiers and others. Finally, increased scrutiny and further regulation inevitably means greater effort by the industry and higher costs. Despite this the author believes that there are substantial offsetting benefits to be gained by companies prepared to take the initiative in improving resource management practices and communicating these improvements to shareholders. In order to achieve the benefits however, the industry needs to fully engage in the changes that are taking place û setting its own standards and working with the regulators rather than sitting back and being legislated against. Mineral resource reporting provides a good model of how this process can work and there will be other opportunities in the coming years as the industry seeks to develop best practice in mineral resource management. The author is an employee of Rio Tinto but wishes to point out that the views expressed in this paper are his own and not necessarily those of Rio Tinto.

Jan 1, 2002

By N Boughen, P Ashworth, S Johns, C J. Yeats, A Littleboy

The ocean floor, often called the last frontier, is increasingly discussed in terms of its resource potential û from near shore building aggregate and placer deposits to massive sulfide orebodies in the deeper ocean. Consequently there is an increasing incentive to mine the seafloor. But, do we have the social license to explore and mine the seafloor? Does this nascent industry have support amongst the wider community? If not, why not? And what should be done? To answer some of these questions, the Wealth from Oceans National Research Flagship has explored the social viability of an expanded seafloor exploration and mining (SEM) industry inAustralia. The results show that there are significant geological and environmental data gaps and that, in the absence of sufficient information, stakeholder reaction to the prospect of an SEM industry expansion may be reactionary and negative. This uncertainty means that the perception of risk from the industry is variable and often dependent on individual values. The acceptability of an expansion to the SEM industry is currently precarious, in particular due to the high levels of uncertainty regarding the environmental impacts of seafloor activity. While there are existing federal regulatory frameworks and government processes for the licensing of seafloor mineral exploration and extraction, there is little precedent in the application and implementation of these regulations. The future viability of the industry will be highly dependant on AustraliaÆs ability to improve the knowledge-base underpinning its regulatory regime and also to generate open and transparent communication channels between stakeholders. It will also be dependent on the SEM industryÆs ability to communicate an acceptable value proposition to society. This proposition will need to include the relative impacts of terrestrial and marine mining, the alternative potential uses of the ocean and the multi-use conflict that SEM might engender. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By F Pavloudakis

The installation of on-line analysis systems in the open-pit mines of the Public Power Corporation SA (PPC, the state-owned electricity entity of Greece) is considered to be the key-parameter for performing improved quality control and blending/homogenisation of the produced lignite. In order to investigate the accuracy of these systems under the site-specific conditions of the Greek lignite deposits, a research project was carried out. This was necessary since there is lack of experience in using on-line analysers in mines that produce a fuel of such a poor and largely fluctuating quality. After thorough market research, a dual energy gamma ray transmission on-line ash analyser was installed in Kardia mine of Ptolemais û Amynteon Lignite Centre, which is located in West Macedonia, Greece. The initial results obtained after the realisation of a series of dual-comparison trials (ie using two series of reference values that allow three-way comparisons) pointed out several problems that obstacle the achievement of high accuracy on-line measurements. More specifically, the measurements obtained by the analyser were higher than the concentrations determined by the two laboratories when the ash content was lower than 12 per cent (in wet basis). On the contrary, when the ash content was higher than 12 per cent, the measurements of the on-line analyser were lower than the concentrations determined by the laboratories. In other words, the range of the measurements obtained by the analyser was narrower than that corresponding to the lab analyses results. Therefore, the use of this on-line analysis system under the site-specific operating conditions of Kardia mine does not guarantee improved quality control of the lignite fed to the mine-mouth located power plant. Most probable reasons that explain the above-mentioned problems are the following: The frequent and widely ranging fluctuations of the chemical and mineralogical composition of the lignite transported by the conveyor belt, especially as far as its calcium content is concerned. This result from the nature and the origin of the mineral matter co-excavated with the lignite, which varies from calcareous marls to sands and clays rich in aluminium and silica minerals. The fluctuations of the lignite quantity transported by the conveyor belt. The change of the linear concentration of iron contained in the fabric of different belt parts.

Jan 1, 2003

By B Ilich, M Brad, R Brandli, E MarT

The Wirtgen surface miner was investigated for application to the Cloud Break iron ore deposit since it can selectively mine thin seams and there is no requirement for drilling and blasting or primary crushing as the surface miner cuts and breaks the rock to secondary cone crusher feed size. A physical metallurgical study of the surface miner run-of-mine (ROM) from Cloud Break was conducted to better understand the product size distribution, amount of -31.5 +6.3 mm lump produced, lump stability and physical metallurgical quality compared to conventional drill and blast techniques. Since the Cloud Break mine was not in production, the lump product from crushing and screening of surface miner ROM was compared with product simulations using traditional premining physical metallurgical processing techniques including drop testing of PQ diamond core. Drop test conditioning is widely used in the iron ore industry to simulate blasting, crushing and screening at the mine and subsequent product degradation during handling from mine to port to predict both the amount of lump product on ship and the size distribution of the fines and lump. The size distributions of surface miner ROM for hard, medium and friable ore types show very tight size distributions with very little above 100 - 150 mm, about 60 per cent of the distribution between 75 and 6.3 mm, with less below 1 mm compared to conventional drill and blast ROM. Crushing, screening and drop test conditioning of the surface miner ROM produced more lump in equivalent ore types compared to drill and blast techniques or their breakage simulation using PQ diamond core. The higher lump yield from the surface miner was also confirmed by pilot scale crushing of some 7400 t of surface miner ROM from the Cloud Break trial pit. The lump produced from surface miner ROM was quite stable and showed similar low degradation characteristics to lump simulated from drill and blasting techniques. Product size distribution simulations using conditioned crushed lump from 1 m diameter Bauer hole samples were found to compare well with processed PQ core samples and surface miner product from trial mining at Cloud Break. The Bauer sample method is therefore considered to be a very useful close simulation to actual lump production, although the lump yield is lower.

Jan 1, 2007

By P G. Gaylard

P754 has been an unusual project in that its main aim was to develop a code of practice for metal accounting with the following key objectives:Development leading to an agreed industry standard at corporate governance level Significant improvement of the credibility of metal accounting from deposit to saleable product Development of guidelines for data collection, data analysis, reporting and audit A data analysis toolbox which provides go/no go testing for metal balance data Promotion of industry adoption of these guidelines to improve transparency and financial credibility. Over time, these guidelines may evolve into a code and eventually into a standard Develop and train engineers to become expert in metal balancing and reporting. Papers like this one and the workshop which follows this conference are part of promoting the code for adoption by industry. Developing a code of practice has traditionally been the provenance of professional bodies associated with particular industries û often on a voluntary basis. Given todayÆs industry pressures, it was felt that funding key input might accelerate the development process as well as offer opportunities to research some of the problems and to train some post graduate students in a difficult discipline. In fact, the project has brought together six industry sponsors from a wide range of process types, three research providers, and funded students in South Africa and Australia. The project has also attracted input from the financial community. A textbook to support the application of the code has also been written. The industry sponsors have made the Code and Guidelines available on request to help to facilitate its use by the mineral industry beyond the sponsor group. The Code and Guidelines have already been translated into Spanish and Portuguese which suggests that industry acceptance may happen quite quickly. The main thrust of the code is to integrate commercial and technical performance to a much higher degree. The Check in-Check out (CI-CO) method has been chosen as the vehicle for this combined approach. The mass and metal values used for CI-CO are 'absolute' and provide the basis of financial transfers. The CI-CO process occurs at each transfer of custody - whether between divisions within a company, or between companies. This approach means that measurement of mass and metal flows becomes the critical element of the process and that a quantitative knowledge of measurement accuracy and precision is also essential. This knowledge allows technical differentiation between differences which are within the expected margin of variation and those which must be formally identified as discrepancies and subject to a process of investigation and sign off. Hence, the application of the code for most companies should be more evolutionary than revolutionary, but with substantially more emphasis on measurement and definition of measurement error. Where this can be achieved, it should bring the mineral industry more into line with other industries competing for investment funds, community acceptance and future employees.

Jan 1, 2008

By D Lau

Traditionally X-ray diffraction (XRD) has not been significantly used by the cultural heritage sector, as the most commonly used technique, X-ray powder diffraction (XRPD), requires sample removal from the artwork or artefact, followed by grinding of the sample to a fine powder. With the development of micro-X-ray diffraction (micro-XRD) and other associated advances, non-destructive, in situ analysis of crystalline pigments on micro-areas of paintings and artefacts has become possible. This is illustrated with the application of this technique to the in situ analysis of propriety paints, paint cross-sections and small paintings. However, workers have noted that XRD can be insufficiently sensitive with pigment mixtures, due to matrix effects. This study obtained X-ray diffractograms of 17 single pigment preparations and determined relative amounts of crystalline content. The purity of single pigments was compared with Joint Committee on Powder Diffraction Standards (JCPDS) database diffractograms. The impact of pigments with high X-ray absorption coefficients on the detection limits of pigments with low X-ray absorption coefficients was further investigated by building on work done with the chromium oxide-zinc oxide series with the preparation of a second series of binary mixtures of zinc oxide (which has a high absorption coefficient and is almost fully crystalline) and ultramarine blue, which has a lower absorption coefficient but which is more crystalline. Semi-quantitative analysis, where baseline and absorption factor corrections are made, confirm detection limits as low as five per cent for chromium oxide and ultramarine blue when in a binary matrix with zinc oxide. However, this type of analysis is very time consuming. So in order to theoretically simulate issues that will be encountered with binary pigment mixtures, the single phase diffractograms were used to theoretically investigate the matrix effects of the three white pigments with the various coloured pigments. This illustrated that detection limits can be as low as five per cent or in non-ideal conditions, such as with partial peak clashes or where there are large differences in relative peak intensity, as high as 50 per cent. These results have significant implications for the analysis of painted surfaces on artworks or artefacts. It has been demonstrated that ideally this method is more suited to the investigation of surfaces where there is minimal mixing of pigments or where there is not a significant difference between the absorption coefficients of the mixed pigments.

Jan 1, 2008

In the introduction to a recent paper dealing with, the relationships of magnetite and hematite in the banded iron formations or "jasper bars" of the Western Australian pre-Cambrian(17)t the author made a brief mention of these interesting rocks, of the principal series in which they occur and of a few of the rock and mineral types to be found within them.He drew attention to the essential shnilarity of these Western Australian banded iron formations to those of the pre-Cambrian of such other countries as the United States Lake Superior region, Sweden, South Russia, India, South Africa and Brazil, and gave a brief summary of his views as to the origin of the formations in Western Australia. Furthermore he stated that the banded iron formations have proved of considerable direct economic importance in the goldfields and other' regions of Western Australia, and he referred to the assistance they have provided the field geologist in geological mapping and the determination of geological structures.It is in elaboration of this last statement that the present paper has been written. In the following pages will be found some examples of the use to which the jasper bars have been put in the determination of the geological structure of critical areas in the goldfields of the State.Firstly, however, it may be as well to recapitulate the features of interest in these rocks. The true jasper bars or banded iron formations including the types jaspilite, banded hematite quartzite and banded magnetite quartzite or chert, together with their higher grade metamorphic derivatives such as banded magnetite-gruneri~ quartzites, magnetitegrunerite schists, fayalite ,and hedenbergite bearing handed magnetitegrunerite quartz rocks and' to 'a lesser extent magnetite-hypersthene grunerite quartz rocks, are abundant in the older series of the Western Australian pre-Cambrian. They are best developed in the older Greenstone or Kalgoorlie series of the goldfields districts, interbedded with metamorphosed basic lavas, tuffs and sediments. The mineralogy andpetrology of these rocks, the history of their metamorphism and their origin have been discusseq elsewhere in some detail by the author(19), (20). In one of the papers(20) it was clearly demonstrated that in the light of the true facts the old silicified shear zone theory of the origin of the jasper bars is quite untenable and that the formations undoubtedly represent sedimentary horizons as was recently pointed out by McKinstry(14).It has also been shown that banded ferruginous cherts, quartzites and cherty carbonate rocks of much lower metamorphic grade are well developed...

Jan 1, 1943

By R Crookes

Mine to mill optimisation is not a recently developed concept. It is one which is finally gaining greater acceptance in the Australian mining industry, possibly as a consequence of the downturn in markets and certainly made possible by the development of tools and techniques to measure and predict performance of mining equipment and milling plants. Fragment size after blasting has a major bearing on the performance of all aspects of mining and a major influence on the economics of the mine and mill. The process to optimise fragmentation consists of identifying the key factors, measuring their sensitivity through a modelling and trialing program and conducting economic evaluations on the changes on both the mine and mill. Management of the Ernest Henry copper-gold mine in Northern Queensland, Australia, has espoused the mine-to-mill concept and is actively pursuing excellence in blasting to drive down the total cost of mining. Ernest Henry has extremely hard, wet and heavily jointed geological conditions, and had high powder factors and a large percentage of oversize material reporting to the crusher or ROM stockpile. A blasting improvement program was undertaken between Ernest Henry Mining, Thiess Contractors and Orica Explosives to optimise the ore size distribution, particularly the oversize component, as a step to reducing production costs. Measures of success included bringing the rock breaker back from double shifts to part-time operation and increasing direct dumping into the crusher from 70 per cent to 92 per cent. Tools and technologies to predict and measure the performance of individual blasts are needed before it is possible to optimise fragmentation or the downstream processes. These include such specialised Orica Explosives tools as SABREX, POWERSIEVE, and POWERLINE and commercially available drill monitors. As important are the more common still and video camera, borehole loggers, measuring tapes, surveying equipment such as face profilers, and a high speed camera if possible. There are many tools which can be applied however it is rarely necessary or possible to use all of them due to time constraints and a point of diminishing returns. The critical point is knowing what the true parameters of the blast were compared to design -only then can the predictive tools be effectively utilised. Stage one of the program has seen gradual improvement as the understanding grew and practices have been implemented resulting in reduced bridging in the crusher, geological mapping with respective blast designs and the oversize component under control. This paper is about a process approach which links tools and technology to understand the fragmentation drivers and then to optimising the size distribution. The continuous improvement program continues . . .

Jan 1, 1999

By G Solly, P J. Leevers

Day-to-day operating practices at existing operations need provide high quality data for decisions that will impact directly on the potential value of the available resource, in addition to meeting standards of quality expected of data used in feasibility studies that will be completed to obtain additional capital required to finance operational improvements. Drill hole location, down hole survey and assay data standards of accuracy and precision have received considerable attention in recent years. The authors propose that geological descriptions of both cored and non-cored drilling warrant at least equal attention, considering their fundamental role in establishing the framework used for geological modeling and resource estimation. The iron ore deposits of the Middleback Ranges have been a major source of iron ore for almost a century. High-grade hematite-dominant ore is currently mined by OneSteel from three open pit operations supplying ore to the companyÆs integrated steelworks at Whyalla. A review of OneSteelÆs future iron ore resources, commenced in 2002, highlighted the need for more flexible and comprehensive management of all forms of geological data used in resource evaluation. Driving this program was the information needs of feasibility studies of the Iron Magnet deposit, located beneath the existing Iron Duke and Iron Duchess mines. Prior to the beginning of 2003, resource evaluation drilling data collected by OneSteel was managed using an in-house system based on industry standard relational database software. The system was demonstrably effective in ensuring the fundamental integrity of basic drilling data, but lacked necessary capabilities for the acquisition and management of geological descriptions, geotechnical and geophysical data obtained by down-hole logging. OneSteelÆs existing system for the management and interpretation of geological descriptions was restricted to storage of a single three digit code for each lithological description interval. The original logs for a large number of older drill holes could not be located, having been either poorly archived or culled from the database in the belief that they did not contribute to the understanding of the resources currently being mined. The three digit codes represented a combination of lithological and stratigraphic descriptions, including many subtle variations in iron ore colour and texture believed to be associated with variations in geochemistry, but subsequently demonstrated to be either incorrect or inconsistently applied. This resulted in the establishment of a plethora of codes for a relatively small number of distinct lithologies. Improvements implemented by OneSteel geologists addressed these shortcomings by ensuring the new data management system: facilitated the objective description of lithological characteristics; distinguished between obsevations and interpretations (eg lithology versus stratigraphy); promoted consistency between descriptions provided by different geologists; and helped to ensure data integrity by developing an audit trail for alterations made to data subsequent to its acquisition. The data used to develop interpretations of mineralisation distribution and characteristics are fundamental to the effective utilisation of a mineral resource: any mineÆs most important asset. Resource related risk is widely recognised as the principal source of technical risks affecting resource development projects, whether they are new mines or expansions of existing operations. A key lesson from this work is that most commercial or æin-houseÆ developed geological data management systems are able to handle basic data validation tasks effectively. Geologists, however, need to ensure that the data management system is appropriately structured to help promote the acquisition of objective and consistent data for interpretation.

Jan 1, 2003

The underground coal mining industry in Australia has, in the last 30 years, undergone a revolution in production methods, techniques and results probably unparalleled elsewhere in the world. It can lay claim not only to leading the fight against pneumoconiosis and setting high safety standards generally, but has at the same time recorded comparatively high rates of increase in output per man shift. The latter has been achieved as a result of progressively matching the latest in production and underground transportation equipment with significant changes in seam development and extraction techniques and the introduction of stress-relieving extraction methods unique to the world scene. However, the seam recovery factor is still too low. Apart from the overall objectives of maximising production and commercial returns with the greatest safety, there must be a concentration towards maximising seam recovery, particularly in high seams. The search will continue for systems which are more completely continuous mining operations than the present stop-go operations, with longwall having long term potential in this regard, but as yet not sufficiently developed to engender confidence for its more general use. Techniques developed in the last 10 years make the development and extraction of deeper seams, perhaps to 2500 feet or more, feasible with continuous miners as well as longwall. The future will see a greater use of continuous shifts at mines, larger mines with more sophisticated management organisation, extensible belts at the face, better systems of immediate roof support at the face, remote operation of face equipment, greater use of roof bolts and the longer roof cables. With commercial confidence in coal mining now virtually assured to at least the turn of the century, the stage is set for heavy capital development in the industry which will undoubtedly include major research into the whole area of mining methods and equipment. We must ensure that our contribution to such research equitably matches other coal producing countries.

Jan 1, 1975

By G Kuntz, V Wall, B New

The prime aim of the Campbell Mine project was to develop a 3D geological model for the Campbell-Red Lake system to contribute to an exploration model for the region. The base data is composed of over 60 years of geological data covering an area of 16 by 8 km, and from surface down to 1830 m depth. This paper concentrates on the methods used in the GeoSpace system for the processing, integration, display and interpretation of such a large and diverse data set. A block model was developed that recorded the relative frequency of each geological feature within each block. The data input for the block models were based on recoding of the Campbell Mine drilling and channel sample databases into lithological, alteration and structural subsets. The value for each geological characteristic inserted into each block is calculated from all available data that falls within the block. Relative and absolute comparisons of the individual variables provide a targeted outcome from which the blocks are coloured for visual inspection. Different combinations of variable comparisons can be evaluated so that required features are highlighted for interpretation. Blocks are displayed to illuminate the ædominantÆ rock type, according to a formula that may be varied interactively to display the features required by the geologist. This flexibility allows rapid remodelling of lithological distributions, commonly highlighting minor lithological packages not readily visualised in, and interpreted from, drillhole traces alone. The 3D geological model was built from the drillhole datasets and old mine plans utilising standard 3D mining, GIS and database software, with several iterations of plan and sectional interpretation. Near surface bedrock geological interpretations were further constrained by low level aeromagnetic data. The Geospace approach employs an innovative technique for visualisation of the distribution of lithological packages and alteration via block modelling. The method utilises the block model format of data handling as it is considered to be more visible than drilling, flexible enough to incorporate a wide range of data sources, and allows for spatial proximity relationships to be investigated. The method is a simple form of processing large data sets so that results are clearly visible. The calculation is much more rapid than estimation procedures, and does not have any requirement for geostatistical interpretation which is also time consuming. Geospace is not unique to any mine environment software and it is expected to be able to be performed in any system. The proper portrayal of the internal structure of the mineralised body will provide practical input to exploration and mining principally in the areas of resource estimation, exploration vectoring and ore/waste characterisation and may be incorporated with other data to include mine support and mine scheduling.

Jan 1, 2003

The Sydney Coalfield, Nova Scotia contains extensive undersea longwall mining operations which are expected to continue well into the 21st Century. A long term research program has been initiated by the Cape Breton Coal Research Laboratory to investigate the full spectrum of problems associated with undersea mining and develop specific guidelines for use by the mine operator. At present, research is centred on the detailed evaluation of existing undersea sub- sidence guidelines, the identification and development of instrumentation capable of moni- toring seafloor subsidence profiles and the effective sealing of offshore exploration boreholes. In addition, work is also planned to examine in situ strata permeability changes occurring between the mining horizon and seabed and the feasibility of using artificial islands.

Jan 1, 1986

IT will be noticed, from the following contributed papers on the various plant, what an infinite number of parts are required to be kept in active operation in order to derive a resultant product of commercial value from the ores and materials received at the works. Crude ores and concentrates, in every degree of complex structure and resistance to treatment, are arriving daily from near and distant places, moreover their metallic contents are so varied that an outsider, unacquainted with the operations, would naturally wonder how it is possible that the rare elements are to be sorted out and classified into their true order, to meet industrial requirements.The proposition is necessarily not a simple one and owners of mining properties have naturally refrained from smelting their complex ores on account of the technical difficulties of attaining high efficiency and recovery of the metals, where limitations are imposed in procuring a variation of ores that lead to the best smelting and refinmg result. This difficulty obviously imposes many disabilities on the smelter, who is prepared to accept all such complex ores, and it may be said that were therenot available a large weekly supply of lead concentrates from the company's own mine at Broken Hill, of standard quality, much of the material being treated in the world today would certainly not be marketable.In order to sustain full efficiency, each section of the works must maintain its.true balance and synchronize with the requirements of such other departments as are dependent on its partially treated materials. This harmony of operations is not only imperative as regards tonnage output, but also relies on the condition of the resultant treatment by each plant, no large variations being permissible.The various officers are, therefore, dependent on one another to keep the order of the operations flowing regularly. This is accomplished by constant intercommunication and observation, as...

Jan 1, 1918

By G R. Hancock, J B. C Lowry, T J. Coulthard

A reconstructed landscape may exert long-term influences on its surrounds and behave in ways that may not be predictable given uncertainties regarding climate, soil and vegetation interactions (Evans, 2000). In recent years, computer-based landscape evolution models (LEM) have been used to assess potential and existing mining landscapes and their long-term geomorphic behaviour (Hancock et al, 2007; Hancock, Lowry and Coulthard, 2015; Tucker and Hancock, 2010).In this paper, we focus on the evolution of post-mining landforms, which are designed to include burial or encapsulation of mine-impacted areas and materials, including tailings, drains, spoil tips and other industrial architecture (Figure 1). At the Ranger Uranium mine in the Northern Territory of Australia, low-grade uranium ore, tailings, brines and other mine wastes will be buried at depth in the areas of the former pits and tailings storage facilities.The use of LEMs to predict long-term landscape evolution has several issues. These include that model predictions are based on the calibration and parameterisation of the model carried out using values determined from present day, or recent surface conditions. Furthermore, there is also the question as to how subtle perturbations or roughness on the DEM surface can produce alternative model results by randomly varying the elevations of the DEM surface.In this study we examine the effect on sediment transport rates and geomorphology for a proposed rehabilitated landform using multiple landscape realisations with increasing magnitudes of random changes in the DEM using the SIBERIA LEM (Willgoose, Bras and Rodriguez-Iturbe, 1991).CITATION:Hancock, G R, Coulthard, T J and Lowry, J B C, 2016. Use of landform evolution models to assess uncertainty in long-term evolution of post-mining landscapes, in Proceedings Life-of-Mine 2016 Conference, pp 67–70 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By R H. Yoon, M Gupta, A Noble, K Huang

Froth flotation is the most commonly used separation technology in the mineral industries. Given the complexity of the pulp and froth phases as well as the multitude of operational parameters that influence flotation performance, purely fundamental models with strong predictive capacity are limited. As a result, accurately modelling modifications to an existing flotation circuit are challenging, particularly when using empirically-derived models from a different operating configuration. Despite these complexities, a recent publication by the authors (Huang et al, 2022) has shown that flotation rates can be accurately predicted from a first-principles model that incorporates hydrodynamic parameters (eg pulp density, superficial gas velocity, feed flow rates etc), surface chemistry parameters (eg contact angle, zeta potentials and surface tension), and size-by-class liberation data. Circuit simulations using this model were shown to be effective in predicting experimental graderecovery curves from the size-by-class mineral liberation matrix. Since the model is derived from fundamental characteristics of the flotation system, it can be used to simulate alternative circuit configurations with varying degrees of recycle. Conventional flotation circuits are operated in a closed-circuit configuration by routing the cleaner scavenger tails (CST) back to the rougher feed to provide an additional opportunity to recover the slow-floating particles. This widely-used flotation strategy has been under constant debate, and several researchers have provided evidence that open circuit configurations provide higher separation and better circuit control (Konigsman, 1985; Bulatovic et al, 1998; Thompson, 2016). Recently, Finch and Tan (2021), used linear circuit analysis to show that open circuit configurations have a fundamental advantage when stage recoveries are high. Given the limitations of these prior studies, the objective of the current work is to further evaluate the merits of the open circuit configuration through a detailed circuit analysis and simulation study incorporating the first principles model described above.

Aug 24, 2022