Search Documents

By Arndt MB, Bamberg S

The evaluation of risk is becoming more important in the siting of mining operations in the United States as well as the rest of the world. The determination of environmental, economic, as well as health and safety risks is an important step in the planning of any mining operation. Hydrogeology plays an important role in pre-mine planning and in the determination of these risks. The mine operators must determine if ground water would inhibit mining in any way. Factors which are important to consider include mine dewatering economics, slope stability, and other adverse hydrologic impacts. This paper presents methodologies for the characterization of hydrogeological risks for a mining operation. First of all, the term risk analysis is defined and its utility is addressed. Then, stepwise methods for performing a typical risk analysis are presented. Finally, the application of risk analysis to hydrogeology in mining is given. With slight modification, it is believed that these methodologies can be used to evaluate the hydrogeological risks for any mining operation.

Jan 1, 1988

By Yu-Jun Z

According to site measurement and labora- tory experiment, the authors suggest a new mathematical model of grouted rock bolts. The rock bolt is taken as an elastic bar, and the grout is substituted by a set of springs the rigidity of which is given as K. Based on certain assumptions, a simplified formula is deduced. When the category of rock, depth of tunnel, the spacing of rock bolts and the rigidity of springs K values are given, so that we can calculate the radius of plastic zone, and subsequently the convergence of rock at the tunnel inner surface u, and the resis- tance exerted by the rock bolt p. Finally, the length of rock bolt can be determined.

Jan 1, 1987

By Rogers J. F, Bird A. C

The establishment of vegetation for dust control on tailings dams at The Zinc Corporation, Limited and New Broken Hill Consolidated Limited (ZC/NBHC) is outlined. The evolution of practices and techniques employed is described and the problems encountered are discussed.

Jan 1, 1983

By Moorrees C

The end uses of magnesia are determined by both its chemical and its physical proper- ties. There is seen to be an increasing need for products of high chemical purity. Prod- ucts containing 90-95 per cent MgO can be routinely produced by physical beneficiation and calcination of most magnesite ores, the dominant source of magnesia. However, pro- duction of grades containing more than 98 per cent MgO with low impurity levels is not readily achieved physically. Such products can only be readily produced by chemical processing techniques. This presentation outlines the types of impurities present in magnesite deposits and the general concepts that are involved in chemically upgrading them. Of the potential leachants, only hydrochloric acid and aqueous carbon dioxide appear to be commercially attractive.

Jan 1, 1987

The production of copper by the Outokumpu direct blister process commenced in July 1988. The problems and incidents encountered in commissioning the main smelter equipment are outlined. Early difficulties were encountered in process control, hot metal handling, dust buildup in the off gas handling equipment, waste heat boiler tube failures, foam over of hot metal into the waste heat boiler and failure of ancilliary equipment.

Jan 1, 1989

By R Nakia, R Livingstone

Historically the Goldfields of Victoria produced large volumes of gold. Interest in these historical Goldfields has grown over recent years with a view to restarting production of gold. A notable example of this is the Bendigo Goldfield. There is also interest in the Ballarat Goldfield and Ballarat Goldfields Ballarat East Project is a particular example of this. The aim of this paper is to describe the ventilation aspects of the potential Ballarat East project. The mine is proposed as a decline access. The paper gives an overview of the project and in particular the ventilation planning associated with a number of possible equipment scenarios. The paper also analyses the main ventilation pollutants that are likely within the proposed mine as it develops to increasing depth. An attempt is also made to determine the depth at which mine climate will become the dominant pollutant rather than diesel exhaust pollutants.

Jan 1, 2003

By Jones BH

Discovery of the Vera-Nancy deposit in late-1995 followed 12 years of active exploration in and around the Pajingo Epithermal System, an andesite hosted veinfield covering an area of 150 square kilometres at the northern end of the Devono-Carboniferous Drummond Basin in North Queensland. Early exploration targeted open-pittable resources in the numerous auriferous veins and it was not until 1994 that exploration focus shifted to drilling to depths below about 100 metres from surface, which resulted in the Vera-Nancy discovery. That deeper drilling process is still at a very early stage of coverage of the epithermal system as a whole and substantial potential exists for additional discoveries.Drill-out of Vera-Nancy has to-date established a gold resource in excess of 1.4 million ounces. Mine development is proceeding via a twin decline system with first stoped production scheduled for August 1997.

Jan 1, 1997

By Chitombo GP

The proposed guidelines on vibration limits that have been circulated by the Australian Environmental Council, demonstrate the need for an extensive data collection and evaluation program to avoid the enacting of abritrary and costly legislation. The operational or practical influence of blast design and overall economic implications of legislation which further reduces permissible levels of ground vibration are discussed. In a typical blasting operation, blast sizes could become smaller and blasting correspondingly more frequent to meet pro- duction demands. Blasthole diameters and charge lengths could be reduced, increasing drilling costs and associated labour costs. Blast size however, is frequently controlled by factors associated with machinery, grade control, pit control, stope size, production contract levels and other factors which cannot be readily changed for operating mines. Blasthole diameters are frequently deter- mined by existing drilling equipment, length of holes (depth of ore or stope size), geological structure and other factors which are not easily changeable. Typical large scale open stoping and strip mining opera- tions are analysed as case studies. The effects of extreme leg- islative limits and the corresponding operational changes with respect to variations in production costs are discussed.

Jan 1, 1987

This paper describes the characteristics of blasting which set it apart from other methods of breaking rock. The mechanism of rock breakage and the influence of rock proper- ties are then discussed. The strain and fragmentation produced by a cylindrical charge does not change once the charge is longer than 16 blasthole diameters. The influence of bench geometry, charge length and drill diameter are then examined. It is shown that spherical charges have advantages over long slender cylindrical charges. By selection of the appropriate drill diameter, explosive and charge configuration the optimum blasting practice for a given rock to give suitable fragmentation and muckpile profile for sub- sequent handling can be found. The fragmentat- ion depends not only on rock and explosive properties but also on the pattern which dictates how effectively the cracking is utilised. The size distribution of the fragments is given by the Rosin - Rammler equation. Undesirable cracking of the rock in the final wall can be controlled by the careful design of blasts as they approach the final wall. Finally, it is concluded that because of the distance to which blasting can fracture and then displace rock it is suited for the breakage of large volumes of rock.

Jan 1, 1978

By Pease JD, Munro PD

The heavy medium cyclone plant for the preconcentration of silver-lead-zinc ore prior to grinding and flotation was commissioned in August 1982. This paper details the measures taken to get the plant up to design performance which involved modifications to the medium densifying and slimes clarifying sections. Operating experiences to date are described with emphasis on the low medium consumption recorded and severe wear on process equipment.

Jan 1, 1984

New Zealand's Land and Income Tax Act 1954 contains unique incentives for companies engaged in mining certain specified minerals or petroleum. Sections 152 and 153 provide for the taxable income of such companies to be based not on profits made but on dividends paid to shareholders. A significant saving in tax results, particularly where profits are not distributed: but the Act attempts to ensure that undistributed profits are used for further mineral exploration and development. To encourage investment in the mining industry, persons taking up shares in a company mining for the specified minerals or petroleum are entitled to a one-third deduction in respect of monies paid on the shares and used by the company for its purposes; and company shareholders may make loans to the company and write-off such loans for tax purposes to an amount of up to half their taxable income. Maximum utilisation of the tax incentives calls for careful consideration as to whether a mining or petroleum company should be financed by way of loan capital or share capital.

Jan 1, 1971

By N Patzelt, T C. Logan, I B. Klymowsky

In 2003, NEWMONT MINING CORPORATION, the worldÆs largest gold producer, set out to prove that High Pressure Grinding Roll (HPGR) technology is sufficiently robust and reliable to be considered for the treatment of hard rock gold ores. In collaboration with POLYSIUS, a significant trial was conducted and 127 600 tonnes processed, successfully proving the HPGR capabilities on the Lone Tree Mine, Nevada ore û one of the most competent and abrasive ores in the industry. The success has led a number of mining companies to consider HPGRs for the comminution of gold and copper ores.

Jan 1, 2004

By Ritchie IC

Spiral separators have been used to treat heavy mineral sands in Australia for some thirty-five years. They were used as the primary treatment method until the advent of the Reichert cone, which largely replaced them, due to its compact design and relative ease of operation. Spirals continued-to be used as the final cleaning stage before dry separation of the heavy minerals as they remained the most efficient separator for this purpose.

Jan 1, 1986

Ore petrology will fundamentally determine the types of metallurgical processes employed for ore treatment, their operational efficiency and the nature of processing problems encountered. It is therefore paramount that the petrological charact

Jan 1, 1998

Coal pillar design has been based on generalised formulae of the strength of the coal in a pillar and experience in localised situations. Stress measurements above and in coal pillars indicate that the actual strength and deformation of pillars varies much more than predicted by formulae. This variation is due to failure of strata surrounding coal. The pillar strength and deformation of the adjacent roadways is a function of failure in the coal and the strata about the coal. When the pillar is viewed as a system in which failure also occurs in the strata, rather than the coal only, the wide range of pillar strength characteristics found in the UK, USA, South Africa, Australia, China, Japan and other countries are simply variations due to different strata-coal combinations and not different coal strengths.This paper presents the measured range of pillar strength characteristics and explains the reasons. Methods to design pillar layouts with regard to the potential strength variations due to the strata strength characteristics surrounding the seam are Presented.

Jan 1, 1998

The mined-out Old Waite volcanogenic Cu-Zn deposit lies in the Noranda mining district of northwestern Quebec. The deposit has a distinctive pipe-like zone of alteration beneath the massive ore, extending into the stratigraphic footwall. The hydrothermal metasomatism within the alteration pipe produced a concentric zonation. with a peripheral quartz - sericite - chlorite mineral assemblage surrounding an axial core of magnesian chlorite - Phlogopite.

Jan 1, 1989

Feasibility studies in the development of mining projects are fundamental to most investment decisions. It is important that the issues addressed and the degree of detail involved in feasibility studies are consistent with the investment decisions to be taken. Emphasis should be placed on a thorough analysis of critical project parameters prior to detailed investigations being undertaken into other activities which are not relevant to the decisions at hand. Therefore, the issues to be decided upon should be influenced significantly by the stage of development of the project and by the reliability of technical and financial information used in the study. Some of the more critical parameters of feasibility studies are commodity prices, inflation rates and discount rates. Advice is given on the selection of these inputs and also on their application in the feasibility study as the project progresses through its various development stages. The feasibility study should involve not only a formal evaluation of project economics but also an analysis of all project related risks and a comparative analysis of projects competing in

Jan 1, 1983

CABS - Costs and Budget System - is being developed to provide more appropriate tools to assist cost control. The most important of these tools is responsibility accounting, that is to ensure the respons- ibility for costs and budgets is placed at the lowest possible managerial level in the Company. The system design and computer techniques utilized include the use of on-line facilities for enquiry purposes plus entry and validation of data. Data base management is used to permit the complex relationships that exist between data in CABS to be defined and maintained. The system must be flexible in order to cater for organisational and other maintenance changes with minimum time delays. The major outputs of the system are reports produced in several cost dissections, by responsibility, by products by cost collection group and type of expense. A significant role in CABS has been played by users. This includes development, control and review of the system proposals in order to ensure that the objectives and requirements from all sections in the Company are met. This role has included Project Leader for the system plus a committee formed to provide formal acceptance of the system Design.

Jan 1, 1977

By M Magee, D Way

The Mount Isa Copper Concentrator was commissioned in 1973. In 1991, two autogenous grinding mills were installed replacing two stages of crushing, one stage of rod milling and one stage of primary ball milling. The cyclone overflow P80 of the secondary ball milling circuit was reduced to 120 microns due to the increased operating power in the AG/SAG mill circuits. A study of the mineralogy of the milled products and the plant flotation recovery indicated that the installed secondary grinding energy was more than what was required for adequate liberation of the chalcopyrite and half of it had potential for more effective use elsewhere. Halving the secondary grinding energy meant only one of the two secondary ball mills would be needed. The predicted saving in operating cost of one less ball mill was more than two million dollars per annum. This paper summarises various plant trials that were conducted in the Copper Concentrator to decommission one of the two secondary ball mills.

Jan 1, 2004

A considerable debate has arisen regarding the best route for the beneficiation of iron ore. Supporters of jigging technology claim that although the technology is old, due to recent advances in jig control and a better understanding of the separation processes within jigs, it offers significant advantages over dense medium separation, especially in terms of reduced capital and operating costs and simplicity of design. Supporters of dense medium separation claim that this technology is proven to provide the best possible separation and that the gain in efficiency over the life of the plant, compared to that of a jig, will more than offset any differences in capital or operating costs. The truth is that both viewpoints are valid and that the choice is ultimately determined by specific characteristics of the ore being treated. Factors that need to be taken into account in deciding upon the correct option include the size/density distribution of the ore to be treated, the different size fractions which must be treated (lumpy or fines), differences in yield at grade, plant layout and capital and operating costs. Each of these factors will be discussed in detail and a case study for both lumpy and fines will be presented.

Jan 1, 2007