Search Documents

BHP Minerals Ltd operates an open cut iron ore mining operation on Koolan Island, off the coast north of Derby in the Kimberley region of Western Australia. The mine comprises a number of pits, the largest of which is situated adjacent to the coast on the southern side of the island. The lowest bench is currently at RL +2 m, and the mine has planned ultimate depth of RL -82 m. Mining has already extended below the pre-existing water table level, and below mean sea level. In 1984, an extensive program of drilling, geophysics and test pumping was instigated to evaluate the aquifer hydraulic properties and the nature of the groundwater flow regime. With the aid of computer modelling, predictions have been made of the likely dewatering and depressurization requirements, and a conceptual pumping and drainage system has been designed.

Jan 1, 1986

By Jaracz K

At the operation of mine winders in deep shafts considerable oscillations of winding ropes may occur due to elasticity of both wind-ing and balance ropes. The amplitudes of longitudinal oscillations may reach + lm at relatively low frequencies, ranging from 0.5 to 2 c/s. These oscillations may be dangereus for the rope and produce several hazards to the winding installation as a whole. They may cause conside-rable instant accelerations on the pulley and dangerous tensions in ro-pe wires. The excessive acceleration may cause the uncontrolled rope slip on the pulley. Several methods of limitation of these accelera-tions were developed, some of them have been already in control system: of electric drive of the winder. The most simple ones are: a/ limita-tion of the rate of change of acceleration and retardation of the win-der /so called "jerk"/ and b/ the proper selection of regulators of the winder control system to get the optimal control. The trouble in solv-ing the problem of rope oscillations is that the dynamic system of the winder is a nonstationaryone owing to changing distance of conveyance from the pulley. Besides, the system is described by the equations with distributed parameters. The brief discussion of the theory and its practical aspects are enclosed as well.

Jan 1, 1985

A study is presented of the theoretically possible initiation systems for outbursts and the subsequent propagation mechanism.Previous occurrences of outbursts and their correlation to the theoretical system are described. An estimation of the energy release from two energy sources, gas strain energy and rock/coal strain energy, is presented and the relative importance of each source in the severity of outbursts. Summary: The description of mechanisms of outbursting follows the examination of these phenomena at Collinsville in Bowen No. 2 mine and at Leichhardt Colliery, Blackwater. Quantitative material contained in the paper refers to Leichhardt Colliery, Blackwater. Clearly from the work carried out to date gas release has a major part to play in the out- bursting at both of these collieries. In the case of the December 1 1978 outburst at Leichhardt Colliery energy release estimates place gas strain energy release contributing eight times the energy of that from rock/coal strain energy. Even the normal outbursts at Leichhardt Colliery appear to show this trend. Estimates of energy released are for comparative purposes between gas and rock strain energy and the values obtained may be regarded as approximate.

Jan 1, 1980

By I Kolomaznik

Each technological process can be reduced on the transport networks, and namely on the parametric networks and the non-parametric ones. The parametric networks are created by the piping, electrical cables or channels. The non-parametric network is created by the ways, suspended grooves, trackages and also by the belt conveyors or other conveyors for continuous material transport. If we reduce the technological process on transport networks, then, by the creation of these networks models and their mutual interconnection we obtain the model of the whole technological process. The model can be understood as the universal one, without exaggeration, because it is valid for any technological process. However, for us the mining production process is important what represents the mining and transport of raw materials under the support of the ensuring system. In this contribution one of the first attempt is described, and namely how to connect the parametric network which has been already worked out very properly with the non-parametric network what is presented in this contribution by the transport line of belt conveyors.

Jan 1, 2003

By M Denton, M Rheinlander, S Mundell, M Broadgate

The manufacturing industry reinvented its approach to the manufacturing process by managing and measuring it end-to-end. This improved returns on production assets, improved information quality and reduced delivery time, resulting in larger net profits through cost reduction and improved cash flow. Today this approach is standard in the manufacturing industry. Resource development has many requirements in common with the manufacturing production line. These include: control of the various steps, transparency of the state of the process to various levels of the organisation and the overall efficiency with which the process is executed. The authors argue that the introduction of manufacturing execution systems (MES) concepts and technologies to resource development processes will lead to similar improvements in control, transparency and efficiency and could improve profitability and enable staff to work more effectively and make better decisions.

Jan 1, 2009

By Kaji S

The Tsugaru Tunnel, located on the Honshu island approach to the Seikan Tunnel, is 5,880 m long and has a "Shinkansen" cross section of 90 m2 area. The geological formation through which the tunnel passes consists of very soft rock most of which is unsolidified sandstone belonging to the Neogen. The permeability coefficient is in the range of 10-2 to 10-4 cm/s and being water bearing with a high ground water level, the ground is unstable and subject to soil outflow phenomenon. Kajima Corporation, undertaking the Futamata Construction Section (1,420 m long), excavated the tunnel by the upper half heading method with side pilots employing the following countermeasures to cope with these severe conditions.

Jan 1, 1987

By A J. Moore

To control the airblast from blasting to regulatory limits at environmentally sensitive sites near the Collinsville Coal Mining Operations, it has been necessary for Thiess Mining to incorporate a wavefront reinforcement analysis model in the predictive environmental airblast design. Controlling airblast from cast blasting 70 m high faces with 2000-3000 kg of explosives per hole within 700 m of houses presents a considerable challenge to the blasting personnel. This paper describes the model used and summarises the results of an investigation designed to quantify the increase in airblast indicated by wavefront reinforcement diagrams to further calibrate the model for future prediction.

Jan 1, 2004

The occurrence of metallic minerals in Australia to the time of the proclamation of South Australia as a Colony in 1836 was unknown. It is, therefore, perhaps, surprising that British settlers arriving in the Coromandel included among their number a German scientist Johannes Menge who had been appointed by the South Australian Company to the post of Mine and Quarry Agent and Geologist on 1 July 1836. His instructions were to `explore the natural productions of the Colony above and below ground and to superintend the working of quarries of stone and slate, the boring for water, metal, lead, coal and other mines at a salary of ú150 per annum for one year and for as much longer as the Company require your services not however exceeding five years'. In the event, he was to have little influence on those matter.

Jan 1, 1993

The geology and mineral deposits of the West Pilbara Goldfield are described and comparison is made with the Pilbara Goldfield,, In the West Pilbai'a Goldfield two adjacent environments are represented by a predominantly clastic succession and a predominantly volcanic succession. These two successions are lateral equivalents and lithologically they are similar to the classical successions at Warrdiwdbna and Mosquito Creek. How- ever, no evidence of a significant erosional break has been found. It is suggested that the Archaean rocks of: the Pilbara Block represent a single geosynclinal cycle, which culminated in orogenesis, within which-local disconformities have been developed in various places: and that the sub-Mosquito; Creek unconformity at Eastern Creek may be the most widespread of these disconformities, Widespread evidence of'preconsolidation movement, aid the intrusion of igneous rock into. unconsolidated sediment, suggest that tectonism and igneous activity began at a very early stage, This was localised along lines of fracture in an unidentified basement.,.Moveme.nt was primarily vertical and persisted into the older Proterozoic, The sediments were enriched in metal by vulcanicity, chemical sedimentation, and possibly detrit`1' contribution. Diagenesis and metamorphism caused the remobòliyation of the metallic constituents of igneous and sedimentary, rocks which were then localised-in loci of dislocation-formed both before and after consolidation.,.. . . , . .

Jan 1, 1964

In October 1993 it was decided to undertake the fourth phase of mining at Big Bell. This decision followed the exhaustion of open pit reserves in January 1993. Two stages of mining were proposed for the new underground mine. The initial stage would mine the remnant ore, consisting of the rib and crown pillars and lower grade ore on the hangingwall and footwall side of the old open stopes, which were mined from the 1930s to 1950s. Most of the old open stopes were backfilled with either deslimed mill tailings or development mullock, both of which were economic to recover. However, the mineable ore from this resource was difficult to evaluate. The second stage focused on mining ore outside the remnant areas and was initially proposed as a Core and Shell method under a caving hangingwall. This method has since been superseded with sublevel caving, in part due to the very high and deviatoric stress conditions encountered at Big Bell and the relatively long mining cycle required for open stoping. The problems and challenges discussed in this paper will cover the identification of remnant ore reserves, dewatering the old workings, and remnant mining.

Jan 1, 1998

This paper presents results of the experiments carried out in Beth Energy No. 33 Mine for the purpose of alleviating problems associated with cutter roof. Cutter roof problems have delayed the advance of the entry development considerably and maintenance cost of these entries was very high due to the requirement of very extensive and heavy artificial supports. The study includes assessment of the problem, investigation of the geology and lithology of the mines, study of in-situ stresses and corrective measures to combat the problem. Two approaches were selected as the corrective measures: 1) implementing yield pillar concept in order to reduce the effects of in-situ horizontal stresses, 2) designing an effective roof reinforcement system and application procedure. Results of this study revealed that roof strata is weak and in-situ stresses are very high at the problem area which results in development of cutter roof. Implementation of yield pillar concept was found to be ineffective because cutter roof often developed at the entry face concurrent to the development. However, proper design and implementation of roof reinforcement system stabilized the roof and eliminated roof caving during both entry development and retreat of longwall face, despite existence of the cutter roof, at a much lower cost.

Jan 1, 1992

By S Basu, P M. Midhun

Electro-Slag Remelting (ESR) is a process capable of producing ingots with much lower centre-line segregation and better internal soundness than conventional ingot casting processes, as well as lower inclusion and sulfur concentrations. This process is commonly used for alloyed steels intended for critical applications like components of marine turbines, supercritical powerplants and rocket motor casings. It involves melting a metal electrode using electrical resistive heating in a slag pool and re-solidification of the resulting metal droplets beneath the slag layer, forming an ingot. Conventional ESR fluxes consist primarily of CaF2, Al2O3 and CaO, along with minor concentrations of SiO2, MgO etc. The emission of fluoride vapour from the molten slag causes several environmental and health problems, triggering a need to develop and reduce the fluoride content in the ESR flux. The present study aims to develop low-CaF2 alternatives to commercial ESR fluxes without compromising on productivity and the surface quality of the refined ingot. Thus, the modification in chemical composition needs to satisfy properties like electrical resistivity, viscosity and liquidus temperature, essential for efficient ESR operation. Since electrical resistivity and viscosity are highly dependent on the ionic structure of the molten slag, it is important to understand the effect of compositional modification on the structure of the flux. The present study employs Fourier-transform infrared spectroscopy (FT-IR) and Raman spectroscopy to investigate the structural variations in the modified fluxes, especially the effect of changing SiO2 concentration, in comparison with conventional CaF2-rich fluxes. Additionally, thermal analysis (Differential Thermal Analysis (DTA) and Thermogravimetric Analysis (TGA)) has been carried out to characterise the melting behaviour of the fluxes. The findings are compared with simulations carried out using the FactSage™ software, ver 8.3 (GTT Technologies, Aachen, Germany). Simultaneous analysis of liquidus temperature and the structure is expected to help in identifying the practical suitability of modified ESR flux compositions for industrial implementation.

Jun 19, 2024

By I H. Jung, W O. Choe

Gallium (Ga)-containing compounds such as Gallium Arsenide (GaAs) and Gallium Nitride (GaN) are widely used in electronic devices due to their superior electro-optical properties and their usages increase rapidly. For the sustainable supply of Ga to electronic industry, therefore, the recycling of Gallium becomes essential. Pyrometallurgical Ga recycling process involves the complex chemical reactions between slag, matte, liquid metal, gas, refractories, etc. Therefore, the accurate thermodynamic information and phase diagram data for the oxide system containing Ga2O3 is important. In the present study, new phase diagram experiments for binary SiO2-Ga2O3 and ternary CaO-SiO2-Ga2O3 system are carried out using Differential Thermal Analysis (DTA) and quenching experiments followed by Electron Probe Micro-Analyser (EPMA) and X-Ray Diffraction (XRD) phase analysis. Based on new phase diagram data and available literature data, the thermodynamic modelling of the entire CaO-SiO2-Ga2O3 system is performed for the first time.

Jun 19, 2024

The philosophy of computer control of grinding and flotation at ZC/NBHC is presented. The performance and reliability of the in- stalled systems are discussed.

Jan 1, 1978

The port of Townsville is situated on the main north/south rail system of the Queens- land Government Railways and is the eastern terminus of the east/west rail link from Towns- ville to Mount Isa. With a stable beef and wool producing area along the east/west rail route, the expanding mineral industry development at its western end and the continuing growth of the Townsville region the administrators of the port are continually'keeping abreast and ahead of port development to ensure an effective and economic growth of port facilities to meet the needs of the area served by Townsville.

Jan 1, 1974

The variation of austenitic grain size with temperature for the steels XKSlSO and XK9261 was determined using the vacuum ctching technique.It is shown that the effect of temperature on the mean grain intercept is relatively small, up to approximately 950°C. Above this temperature the rate of increase of grain size rises sharply.Within the limits of the 1-4 hr vacuum etching times used the effect of time at temperature is relatively small on the ASTM grain size of the steels.

Jan 1, 1967

By L R. B M Sß

This paper presents the results of a liberation study made on a sulfide copper ore from Carajßs, Brazil, in a mini pilot plant flotation test. The aim of the research was the methodological evaluation of a liberation study using a sample crushed at 1 mm and a sample ground for flotation testing to a target size of 80 per cent

Jan 1, 2005

The developments in hydrocyclone classification in the milling circuit at Bougainville Copper Limited are discussed. A major change in cyclone size and improve- ments in operating conditions have been made. Test work has been carried out to assess the classification performance of a modified Linatex cyclone, Wemco cyclones and a two stage cycloning circuit. The use of a scalping cyclone, to remove coarse material from the present overflow product for regrind, has also been investigated.

Jan 1, 1978

By Eggleton T, Taylor G

The lateral and vertical distributions of gold and a wide range of other elements in the regolith, close to Au and Cu mineralisation have been investigated at Goonumbla, NSW. Open cut mining has exposed deeply weathered profiles which have been used for this investigation. Determination of secondary mineralogy and micromorphology of profiles have facilitated the broad interpretation of processes that determine element mobility and dispersion from primary mineralisation as a result of weathering. This in turn has led to better interpretation of geochemical data and enhanced understanding and knowledge of regolith geochemical processes which are invaluable in the formulation of improved exploration Procedures.

Jan 1, 1997

The Carnilya Hill Mine, a joint venture project between Western Mining Corporation Limited (WMC) and The Broken Hill Proprietary Company (BHP), is a nickel sulphide deposit being developed by the Kambalda Nickel Operations (KNO) of Western Mining Corporation. Seven months elapsed from the time a decision to proceed with the project was taken until the first ore production. During the first month of operation a new KNO record for decline development was set. Equipment used includes an electro- hydraulic drill jumbo, 4 cubic metre front end loaders, and 35 tonne haulage trucks.

Jan 1, 1981