Search Documents

By Burman B. C

This paper describes studies into two particular aspects of the Lochiel deposit which formed part of feasibility level geot2chnical and hydrogeological investigations for proposed open cut mine development. The two aspects were depressurisation of thick beds of silt located through the profile and the determination of characteristics and origins of soil structure and their effect on pit stability. The studies were very detailed and multi disciplinary and highlight the integration of geology, geotechnics, hydrogeology and mining that is required for mine development studies. It is considered that as more marginal deposits are developed throughout the world the demands for efficient economic mining together with in- creasing scales of operation will require simi- lar types of studies. As such the studies pre- sented herein are likely to be a forerunner to a,emerging trend for development of open pit mines in difficult ground and water conditions.

Jan 1, 1986

By N Meyer

This paper presents a research project referring to the stability of submerged walls of open pit mines and the actual state of development. Obviously the slope stability analysis is always a rather complex problem, because it is difficult to reduce the problem to a design scheme and to define the available in situ soil strength. Especially the design of submerged slopes represents a problem. The state-of-the-art slope stability analysis is based on a simplified modelling of slope failure and soil behaviour and with this predicted stable slope inclinations of sand slopes below water-table are less then half the angle of internal friction. Slope angles calculated like that canÆt satisfy the mining companies. One of the problems that have to be solved is the reliable determination of the long-term stability of non-cohesive, submerged slopes, which is not only dependant on geotechnical and hydrogeological parameters of the subsoil, but is also significantly influenced by how the slopes are made. The research project points at the relations between mining and geotechnical engineering with the main aim to find a more suitable stability analysis which takes both soil behaviour and mining influences into account.

Jan 1, 2003

Many stress measuring instruments use overcoring stress-relief principles but adopt different sensing techniques. Every technique is subject to certain limitations of rock types and conditions. To investigate the performance and reliability of the instruments in field measurement, a simple and practical approach has been developed to allow comparable laboratory results to be obtained which simulate in-situ rock and stress conditions. Four commonly used devices, the USBM deformation gauge, the CSIRO HI cell,the CSIR triaxial cell and the UNSW SI cell were thoroughly tested in the laboratory. Some conclusions have been drawn as to their suitability and reliability in different field conditions. Recommendations are provided for the choice of an appropriate technique for a given rock type and condition. A new thin-wall cell that overcomes the disadvantages of earlier devices has been developed and tested. Its laboratory performance shows that it has good prospects.

Jan 1, 1990

By Ibaragi K

High grade ores were intersected in 1981 by a scout drill carried out by the Metal Mining Agency of Japan during a reconnaissance dril ling programme. The original aim of the hole was to explore a deep target where geophysical anczralies overlapped the abandoned old drifts (gravity- high, resistivity-low by airborne EM, and resistivity-low near the surface and high at depth by Schlumberger deep sounding). Subsequently, a follow-up drilling programm was commenced by the Sumitcrro Metal Mining Co Ltd, and all the 18 holes intersected high grade ores. The resources were then "guestimated" to contain ca.120 tonnes gold with an average grade of 80g/t Au between -40m and +120n a.s.l. The underground development was started in December 1982 and the first crosscut intersected the ore body at 100m level (a.s.l.) in July 1985.

Jan 1, 1987

The term "joint venture" lacks any precise legal definition but is typically used to denote a form of legal relationship which is neither a partnership nor a corporation. Nbst joint ventures are contractual relationships which provide for the sharing of mining leases and production facilities and for the sharing of costs, but which enable each joint venturer to carry on his own separate business. The rationale for such relationships is that each participant: retains independent taxation status may independently grant direct security over his interest in the project assets for financing purposes Bankers prefer to lend to incorporated joint ventures (i.e. corporations in which all of the joint venturers are shareholders) but will lend to individual joint venturers provided the joint venture agreement does not imperil their security; i.e. provided there is a "bankable" joint venture. The carpeting objectives of joint venturers and their bankers may be reconciled and unnecessary conflict avoided by the timely inclusion of appropriate provisions in the joint venture agreement before financing negotiations commence.

Jan 1, 1983

With mining development on hold and other underground works in a slowdown, the develop- ment of nuclear waste repositories takes center stage on the American rock engineering scene. Three repositories for commercial spent fuel -- in salt, tuff, and basalt -- are in the phase of site characterization and conceptual design, and one pilot project for defense high-level waste in salt is under construction. A repository design for crystal line rock has recently been postponed. Because of strict quality assurance requirements throughout design and construc- tion, and because of the need to predict and ascertain in advance the satisfactory perfor- mance of the underground openings, much intellectual energy has been expended to analyze underground openings in the unusual circumstances of the repository environment. In the long term, these efforts will lead to an improved understanding of rock behavior and improved methods of underground analysis and design. For the shorter term, a formalized ground control plan was developed, the princi- ples of which may be applied to other types of projects. This paper summarizes the status of underground design and construction for nuclear waste repositories and presents some details of the ground control plan and its individual elements.

Jan 1, 1987

By Williams D. J

The boundary element method is one of a number of tools that have found wide application in geomechanics for mine design and stress analysis. Two examples are presented in this paper, illustrating the use of the boundary element method to find potential problem regions in large-scale excavations. These examples are from a Papua New Guinea open cut mine and an Australian sub-level caving operation. Because of the scale of the mines and the complexity of the excavations, the boundary element method is the only practical numerical modelling technique to account for the major influences. Although the boundary element method uses only linear elastic models of the rock mass, the paper illustrates techniques for dealing with non-homogenous and anisotropic rock masses, as well as clasto-plastic effects associated with an excavation.

Jan 1, 1995

By McConachy G. W, Wright J. V

During the 110 years since the discovery of the Broken Hill PbZnAg deposit six major mining companies have mined the ore body and explored the ore environment. Despite this activity, no new orebodies have been found at Broken Hill. The failure to discover large new resources cannot be attributed to a lack of activity because major companies have maintained substantial exploration commitments over many decades. This suggests that not only was a unique coincidence of conditions required to form the deposit but also that full recognition and definition of the critical parameters may not yet have been recognised. In an attempt to illuminate some of the more unusual and poorly studied characteristics of the ore environment some new areas of investigation are presented here which may contribute to understanding the ore deposit setting and focus exploration towards different and perhaps more productive targets. Sedimentological characteristics of the host succession of the Broken Hill deposit are apparently unique along the line of lode. An upward-coarsening megasequence reflected in the development of clastic psammites stratigraphically below the ore deposit is one important ingredient which has received little exploration focus. These psammites also host mineralisation and form part of a spectrum of quart-zrich rocks collectively referred to as gametiferous psammites, garnet quartzites and blue quartz lodes. Sedimentological data interpreted from outcrop, drill core and downhole geophysical well logs support a elastic origin for some of these rocks; an interpretation which is at variance with traditional interpretations favouring an exhalative origin. A clastic origin for many of the footwall psammites, and their close spatial association with the orebodies suggests their role in ore formation was important. It is interpreted as a critical part of the fluid flow architecture within the sedimentary basin, which focussed ore forming fluids into an unique environment favourable for trapping mineralisation. Detailed stratigraphic correlation near the deposit has also highlighted that quartzofeldspathic rocks (Potosi gneisses and lode pegmatites) have complex relationships with ore. Suites of stratabound quartzofeldspathic pegmatites have received limited study, but their distribution and voluminous development suggests they may be as important to ore formation as the psammitic lode rocks which host the orebodies. These associations are not in conflict with some recent ore forming models invoking deposition in a shallow water environments of deposition. The geochemistry of parts of the host sequence has been studied extensively in the past but this has not been merged with current stratigraphic subdivisions. A large drillhole data base now permits the geochemistry to be related to the sedimentary succession and reveals that a signature involving stratigraphic vectors best illustrated by changes in MnO, Na2O, Pb and Zn can be detected. This is interpreted to reflect sedimentary basin processes as opposed to a classical volcanic hydrothermal alteration pipe associated with seafloor venting. The stratigraphic setting together with characteristics of some of these poorly understood areas is discussed to emphasise that construction of sound models for exploration requires the total ore environment to be studied with attention directed to the geometry and setting of the full range of host rocks. Control of the greater portion of the line of lode by a single company, Pasminco Australia Limited, now permits disparate datasets and observations to be merged and presents new opportunities and encouragement for model refinement and exploration success.

Jan 1, 1993

I am sure that you are- all familiar with Airborne Magneto-meter Surveying so I shall-spend only a brief moment describing the instrument and techniques and the remainder of the allotted time-on-modern-application-of the instrument.The Airborne Magnetometer used by Aero Service in AUstralia-was designated by Gulf Research and implements the saturable-core flux-gate--principle. The first magnetometers developed'weremagnetic-balances and depended on the counter-torque principle but these required a stable platform and hence are not applicable to airborne surveying. Other methods include the induction methods, the Hall Effect methods, magneto-striction methods., Deflectioh. of,free.electrons, the proton-precession methods.Some: of these are applicable to airborne surveying. As a matter of-fact the nuclear precession magnetometer is the one generally used in the Satellites because it has been miniaturized most successfully.The Gulf Magnetometer is the one most generally used in mineral and petroleum exploration because its sensitivity is sufficient for the problem and-data and instrument techniques have been worked out and standardized.

Jan 1, 1962

By Kapoor M. L

Emf measurements on SE galvanic cell: SS; Ni-NiO I solid electrolyte/ZrO2 + CaO I [Pb + Bi]liq alloy; (PbO); SS were made in the temperature range 913-1034 K to determine the thermodynamic properties of oxygen dissolution in liquid lead. Bismuth alloys with bismuth in the dilute concentration range of 0 to 3.08 mass per cent and oxygen in the alloy varied by equilibrating the metallic system with a suitable (PbO) slag. Wagner's interaction parameter approach was used to calculate the ternary interaction parameter, eBiO at temperatures of 913, 953 and 993 and 1034 K and to observe the temperature dependence eBiO = 19 200/T - 17.454. Quasichemical fonnulation was employed to yield lnf BiO and reveal the effect of bismuth on oxygen in lead. The results obtained are discussed on the basis of theoretical models and the value of Wagner's energy parameter 'h' estimated to predict the results in a Pb-Bi-O system.

Jan 1, 1995

Minerals and Metals Group (MMG) Century mine (Century) is a large open-cut mine in northwest Queensland approximately 2.5 km long, 1.5 km wide and 240 m deep, with an ultimate pit depth of 320 m. In 2009, the mine experienced three failures which began as small failures, and progressively developed into significant multi-batter failures. The incidents were managed by a combination of analysis, redesign and practical management to achieve positive outcomes for the mine. On the south wall of the mine, a series of batter-scale wedge failures occurred in December 2007. Analysis of structure orientations and design changes aimed to minimise the risk of failure extending over multiple batters, while accepting a risk of further small-scale failures. Design changes were constrained by a culturally sensitive area (CSA) located south of the wall. As mining progressed, shallow wedge failures developed over multiple batters and cracks were observed 60m back from the pit crest, indicating that a large-scale wedge failure was developing. Movement increased in January 2009 as a result of significant rainfall. After considering several design options, the area was stabilised by a cut-back of the wall. Two multi-batter failures also occurred on the north wall as mining progressed through a structurally complex area. Both north wall failures began as small failures that progressively developed, and required a redesign of the wall below as well as practical management of safety aspects. The complex structural geology was difficult to predict ahead of mining, and required geotechnical input into design changes as mining progressed. All three failures potentially had significant impact for ore recovery, and were managed by a combination of analysis, redesign and operational management have resulted to achieve positive outcomes in a challenging mining environment.

May 1, 2010

By Paley N, Cameron A, Townson P

Although blasthole deviation is a problem which can seriously affect blasting operations, there is little practical emphasis on controlling this deviation and no practical emphasis on understanding its practical behaviour. The most common way of dealing with it involves tight control over drill set up and surveying hole paths. The surveying might involve simple collar location and inclination measurement to estimate the hole's actual path. At best, some operations routinely survey hole paths after all holes in a stope have been drilled. In addition, although there is an expectation that holes will deviate, there is no planning for this behaviour in order to reduce its impact on the blast. Design decisions are invariably made with the assumption that holes are straight. If and when surveys reveal problems it is possible only to adjust charging and initiation to 'work around them'. In extreme cases the drill might be recalled to fill in gaps. The lack of planning and the lack of understanding are doubtlessly linked.A model is presented that will predict the expected path of a drill hole. By knowing how a selected few holes deviated it is possible to make a good estimate of the deviation of other holes in the same rock mass. After minimal calibration the model can be used to increase the amount of information for a given amount of surveying or the amount of surveying can be reduced while maintaining the same level of knowledge of blasthole deviation. Equally important is the ability to plan for the deviation in future drilling through altering the initial collar angles or drilling from different locations. It is the authors' hope that planning for hole deviation becomes as much a part of the design process as planning for detonator delay scatter and explosive performance variation.

Jan 1, 1992

The Ok Tedi open pit mine will have final wall heights in excess of 750m. The behaviour of these excavated slopes will be influenced by the presence of numerous defects. This paper discusses the identification of possible failure mechanisms within the pit walls based on mapped fault and joint data. Results from analyses using these data have formed the basis for the ultimate pit design.

Jan 1, 1994

By Armstrong M

The highest grades of the Porgera gold deposit, Papua New Guinea, are contained in Zone 7 due to the presence of the Roamane fault, which acted as channelway of the gold-bearing fluids. Prior to the development and underground mining of this fault-controlled high-grade zone it was critical to provide grade estimates of relatively small mining units, and of the proportion of mining units above cutoff. To be applicable to Zone 7 of Porgera a grade estimation method should account for the following:1. the highly skewed and apparently lognormal distribution of the grades,2. the rapid drop off of the local mean grade and the variance as the distance to the Roamane fault increases,3. the presence of high grade pockets in the footwall, away from that fault, and4. the existence of variograms for the logs with sills parallel to the fault and without sills perpendicular to it.

Jan 1, 1990

Following unprecedented high market prices for tin and gold in 1980, significant advances in both mining technology and geological knowledge took place in northeast Queensland. These led to a rapid growth in mining activity. Production of these traditional metals reached levels comparable to those of the heyday of mining activity at the turn of the century.Although tin and tungsten prices have since collapsed, the geological knowledge gained and significant discoveries made during the boom, have created a potential for mine development when prices rise again. For other discoveries which are not workable because of treatment problems, future technological advances are required to raise their potential.

Jan 1, 1990

By Willis I. L, Stevens B. P J, Stroud W. J

The Early Proterozoic metamorphic rocks of the Broken Hill (BH) Block have been recently subdivided into sixteen formations and four groups (Willis et al., 1983b, Stevens et al., 1983). This stratigraphic subdivision has relied upon recognition of distinctive mapped rock units and "associations" of mapped rock units, which characterize particular lithostratigraphic units. The rock units and rock unit associations define local ordered sequences which can be compared and correlated, thereby establishing the stratigraphic succession. In the Clevedale homestead, Thackaringa, BH City, Bores Mine-Freyers mine, Silver King mine, and Brewery Well areas, coherent stratigraphic successions have been interpreted. These areas illustrate the regional variability of the stratigraphic succession and facies changes within individual stratigraphic units. Stratigraphic type sections are located in the Thackaringa, Bores Mine-Freyers mine, Silver King mine, and Brewery Well areas. The principles of stratigraphic interpretation applied in the BH Block can be used in other areas of Willyama Supergroup outcrop such as the Euriowie, Olary and Mount Painter Blocks. The general technique may also have applicability to other highly deformed and metamorphosed terrains.

Jan 1, 1983

By Olofsson O, Durance M-V, Villeneuve J

Modelling of the Sala Agitated Mill (SAM) using a simplified solution to the population balance approach has been carried out. The rate of breakage is modified by the mill power, providing predictions of the resulting product size distribution for different grinding conditions and mill sizes. The power of the mill is estimated by a physically derived function, using an assumption that the mill power consumption mainly arises from the ball to ball friction within the mill. The grinding efficiency, depending on the media ball size and pulp density is approximated in the model. Experimental work on grinding a complex sulphide ore using a pilot scale SAM 7.5 has been carried out. Good agreement has been found between the data from the test campaign and the simulated values. The model has also been validated with experimental data from a pilot grinding of calcium carbonate and from an industrial mill. The model is included in the USIM PAC simulation software.

Jan 1, 1995

By Borsaru M, Wylie AW

A neutron irradiation technique has been developed which is suitable for the determinat- ion of the iron and aluminium content of iron ore fines (-6 mm particle size) on a moving rubber conveyor belt. The determination of iron entails measure- ment with a NaI(Tl) gamma ray detector of the characteristic prompt gamma rays (7.64 MeV) due to thermal neutron capture in iron, while the determination of aluminium is based on thermal neutron activation analysis. For the latter a second detector must be placed down- stream to monitor the 1.78 MeV gamma radiation emitted after activation of aluminium. Although conveyor speed has no effect on the Fe measurement, it has an adverse influence on the aluminium signal, and the belt speed should not exceed 0.1 m/s if good accuracy is required. Static trials on a 460 mm rubber conveyor belt with constant ore geometry indicate that for iron an accuracy of ¦ 1.2% Fe (2a) can be achieved for crushed run-of-mine ore at

Jan 1, 1978

By M J. Nugus

A substantial cost is invested into the data collection phase of any exploration or development program; notwithstanding, it is impractical to expect a database of information can be collated to ensure a perfect geological interpretation. The question then becomes, is there a possible alternative interpretation and what is the likely impact of the variations? Modelling in 2005, of the Cosmo lode at Sunrise Dam Gold Mine, Western Australia led to consideration of the philosophical implications associated with resource management. It was concluded that several plausible geological models could be constructed from the known geological database. To varying degrees, this predicament is common to all geological reconstructions, as several alternative geological models can be generated at almost any stage that will impact on the resultant resource estimation and mine plan. The significance of that variation and the associated risk of multiple geological models (MGMs) requires due consideration. What is being suggested is that using plausible multiple geological models advances the holistic understanding of a mineral deposit within the bounds of the data collected, providing fluidity for updating geological knowledge and building inherent variability into the design and planning departments where variations of the geological models may materially impact on the resource performance.

Jan 1, 2006

By Quast K

A series of laboratory flotation tests were conducted to evaluate the effectiveness of various depressants as arsenic (and zinc) depressants in the lead cleaner stage of the NBHC mill at Broken Hill. The depressants used included potassium cyanide, ferrous sulphate, sodium hypochlorite, potassium ferricyanide and two Cyanamid commerical depressants, Aerodepressants 610 and 633. A standard roughing stage was completed before the addition of the reagents in the cleaning stage. All reagents tested produced significant arsenic depression, with the best results being obtained with the addition of potassium cyanide and sodium hypochlorite. Some of the depressants activated the zinc in the process of arsenic depression. The best result was obtained with the addition of 90 g/t potassium cyanide at a pH of 10 when arsenic recovery was only 1/4 that of the value obtained for the standard test.

Jan 1, 1991