Search Documents

Investigation of standard tests used to establish the decrepitation rating of Western Australian iron ore showed scatter in results which could be reduced by textural type sampling. Testing of individual textural types resulted in separation.of a range of decrepitation behaviour patterns. No unique correlation was established between water content in goethite, or between any single mechanism and breakage in shock heating. The latter depends rather on several mechan- isms whose operation is controlled by the texture of the ore. Texture studies were used successfully to predict decrepitation behaviour which could be related to orebody structure for mine planning, and blending for sales or processing requirements.

Jan 1, 1973

The mining of remnant coal reserves at the Liddell Open Cut is subject to a number of risks. These risks are of both a technical and financial nature. Liddell Open Cut is principally a conventional truck and shovel/loader operation, supplemented by a highwall coal augering operation. There are significant areas of divergence from more conventional operations including working in close proximity to a major dam, working up dip from an operating underground mine, and working through areas where there has previously been underground extraction. In addition the site has major long-term rehabilitation requirements. This paper, rather than concentrating on specific detail of areas of risk, presents the spectrum of geological, design, operational and post-mining risks that accrue to the various areas of activity in this open cut operation. The balance of this paper then provides an outline of the strategies employed by Liddell Coal to manage their potential impact.

Jan 1, 1994

By Arit I, Adisoma G

General Limit Equilibrium Method (GLE) and Janbu's Generalised Procedure of Slices (GPS) are two limit equilibrium methods in slope stability analysis which satisfy all equilibrium conditions. Numerical difficulties associated with these metho

Jan 1, 1998

The Blackwater Coal Mine is a modern open cut operation using large draglines for over- :)urden removal and shovels, loaders and trucks to mine and haul coal to the crushing and coal ?reparation plant. Operations at the mine are described in sequence following through overburden removal to the railing of product coal from the mine site. The close operating connection between the mine and washery, which results from the blending of raw coal into clean product via the qashplant bypass system, is stressed. Some features of special interest at Blackwater Mine, such as land reclamation and slope stability,are outlined.

Jan 1, 1974

By D W. Nisbet

Today Hudson Bay Mining and SmeltingÆs 777 Project is the largest mining construction project under way in Canada. The project comprises six components: construction of the new 777 zinc-copper mine; construction of the new Chisel North zinc mine that will truck ore out from 600 metres below surface; expansion of the Flin Flon ore concentrator; expansion of the zinc plant to increase throughput by 15 per cent; a spill gas project that will reduce fugitive gas emissions by some 90 per cent; and infrastructure improvements including construction of a new electrical substation. Total investment in The 777 Project is over $US 260 million. Seven years ago, the Flin Flon, Manitoba-based company was fighting for its very existence. How does a company go from down-for-the-count to robust contender in just seven years? Contributing reasons are many, but all have their root in a process HBMS calls æTransformationÆ. It is transformation that has taken HBMS, a very traditional company, through a very non-traditional turnaround (Figure 1).

Jan 1, 2000

By Lumley G. I, Duffy W. J

The risk involved with incorporating new/unfamiliar technology into mines has, in the past, largely been evaluated by the supplier of the technology. The implications on safety and productivity has been accepted as part of the process of `getting up and running'.This has changed. As companies see the lost productivity and accidents actually costing significant dollars, risk assessment is becoming an important part of the implementation of new equipment. Regulatory authorities are also seeing the preventable incidents and in some cases are now requiring a risk assessment to be undertaken on new equipment at a Mine.

Jan 1, 1992

The Kidston breccia pipe is situated approximately 280 km west northwest of Townsville, north Queensland. It is currently Australia's largest gold producer with production varying between 8,000 and 16,000 tonnes of ore per day. Current reserves are estimated at 36.2 million tonnes averaging 1.74 C/t Au and 2.21 g/t Ag. Alluvial gold in the gullies surrounding the deposit was first discovered in the 1880's and between 1907 and 1948 small scale open cut and underground mining was undertaken. Advances in extractive metallurgy and an increase in the gold price were major factors influencing the recent exploration and development of large scale mining of the deposit by Placer Pacific and Kidston Gold Mines. The breccia pipe is trapezoid in shape with surface dimensions of 1100 m by 900 m. Clasts show only limited evidence of mixing during brecciation, with the pre-breccia stratigraphy still discernible on the basis of clast types. This lack of mixing together with the intimate association with intrusive activity, suggests that the brecia formed by collapse, probably associated with the escape of a large volume of irothermal fluid from a crystallising hatholith. Mineralisation and alteration are also sratially and temporally associated with rhyolite emplacement and brecciation. Pre-breccia mineralisation consists of laminated stockwork quartz veins associated with muscovite, quartz and orthoclase-epidote alteration. Stockwork veins contain either anomalous molybdenite or gold. Uneconomic early stage post-breccia mineralisation and alteration consists of cavity infill quartz-epidote and calcite associated with potassic and propylitic alteration respectively. Economic late stage post-breccia cavity infill and sheeted veining consists of quartz-carbonate-sulphide infill associated with phyllic alteration. The grade of gold mineralisation generally decreases downwards in the system with an increase in the amount of pyrrhotite relative to pyrite. Pre-breccia stockwork quartz veins mineralisation is genetically related to the

Jan 1, 1987

By T Baumgartl, B Richards

Covers on waste rock and tailings remain the primary choice for closure planning where the purpose is to create an environment where water ingress into reactive material can be controlled and/or prevented. In semi-arid and arid environments, dry cover systems are the preferred option with the design intention to absorb rainfall and to prevent deep drainage. Although the average amount of rain typical for semi-arid environments is relatively low and evaporative demand is high, the seasonal and annual distribution may vary greatly. Rocky substrates are often the only choice for the construction of covers due to economic constraints or availability of suitable materials. While the water holding capacity may be suitable for the application of a dry cover design in arid and semi-arid climates, some of these covers bear the risk of preferential water flow when rain events are intensive or occurring at high frequency. The objective of this presentation is to demonstrate the occurrence of preferential flow through rock containing dry cover systems. A regional classification for the applicability of dry covers is attempted to delineate those regions of Australia where the characteristic of the rainfall pattern increases the risk of failure for dry cover designs. CITATION:Baumgartl, T and Richards, B, 2016. Rainfall patterns rather than climate classification control cover design for closure, in Proceedings Life-of-Mine 2016 Conference, pp 89–92 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By Baafi EY

Geostatistics is now widely used in the mining industry in the estimation of ore reserves and terms like kriging, variogram and estimation variance are becoming well known. Ordinary Kriging (OK) has been found by some practioners to be a superior tool compared with other ore reserve estimators. However, kriging hasn't been the ultimate solution to difficulties which may arise in ore reserve estimation. Several additional geostatistical techniques have been recently developed for more efficient ore reserve estimation in some deposits, especially gold and other precious metals. These include indicator kriging and probability kriging which are useful tools to work with in a selective mining operation.

Jan 1, 1987

The Racecourse Orebodies at Mount Isa consist of a series of parallel steeply dipping lead/zinc/silver orebodies with a strike length of up to 1000 metres. Production from these orebodies between 13 Level to 9 Level has been by a series of cut and fill stopes in two level stages, leaving a crown pillar at 11 level. Development of the 15 level to 13 level extraction stage has recently been completed. The layout consists of a series of parallel stopes over a strike length of 1200 metres. Access to the stopes is by two declines connecting the stopes with a series of crosscuts This paper describes the basic layout with development and production methods employed.

Jan 1, 1977

By Koppe J. C, Costa J. F C L

This paper compares different results for overburden volume estimation assisted by geoestatistics, particularly using kriging methods. The main goal is to obtain the most reliable digital terrain model for the calculation of the overburden volume. The data was collected on an irregularly spaced grid and interpolated values were calculated to provide a denser, more regular data set before volume estimation. The field work was developed at the Butia-Leste Coal Mine, southern most Brazil, where an accurate survey was done using a total station theodolite with electronic data collector. The study was developed in five main steps: data acquisition, exploratory data analysis, spatial continuity measurements, point and block kriging estimation and verification of the results. Data acquisition was carried out on a 5 x 5 in grid. This dense grid provides an exhaustive data set of the real terrain against which data subsets can be compared for the various interpolation procedures and volume calculation. This provides an interesting insight into the influence of the number of data on the estimation error. Univariate statistics were used to compare each data subset and the exhaustive dataset. Ordinary kriging on the data subsets followed by contouring was carried out using Geoeas and Surfer software respectively. A subroutine written in C provided the link between the files generated in Geoeas and subsequent contouring routines embedded into the Surfer package. Omnidirectional and directional variograms were modelled defining the parameters for kriging estimation using Geoeas. Different variogram models were checked through cross validation prior to kriging. A comparison between the magnitude of the differences in volumes calculated with the different DTMs was attained. These final result indicates the sensitivity of the volume obtained to the number of data points. As the number of data points increases the estimation error decreases, but at some point there is no significant decrease in the final volume with the collection of additional data.

Jan 1, 1995

Various aspects concerning gold are mentioned below. These have no common theme but suggest points of interest any one of which, if warranted, could lead to development later and elsewhere. 'High level' auriferous gravels The gold deposits of Victoria are commonly classified as being either primary or secondary. Most primary occurrences comprise gold present in quartz reefs, together with other lode-like occurrences in which gold is associated with various sulphides, with or without quartz. Secondary occurrences are derived by physical release of primary gold and subsequent concen- tration of it as a constituent of sediments. Secondary gold deposits may be themselves eroded so leading to third or even fourth generation gold.

Jan 1, 1982

WMC Limited, owner/operator of Olympic Dam, the worldÆs largest underground uranium mine and the fourth largest underground copper mine has now completed an expansion that has been classed as a benchmark in the mining industry. To achieve a production increase from 3.4 to 9.25 Mtpa from an underground mining operation in two years was a major challenge, it was essential to review the overall materials handling system from æthe face to the stockpileÆ. The challenge was two-fold:How to deliver 30 000 tonne of ore per day to the processing plant, from a single underground mine? To provide the processing plant with a consistent metallurgical feed. This paper traces the transformation from the old to the new materials handling system at Olympic Dam.

Jan 1, 2000

The dielectric properties of practically all oxide and sulphide ore minerals are such that they heat rapidly when irradiated with microwaves particularly at the standard frequency of 2450 MHz. The presence of carbon or low rank coal mixed with the minerals still further enhances the heating rate. Amongst the patented technologies being investigated are: (i) the direct reduction of oxides with or without carbon included in the pellets or briquettes; (ii) microwave precursor heating of composites ahead of smelt reduction; (iii) microwave smelting of ore or concentrate mixtures with carbon, sometimes assisted with oxygen. Microwaves appear to stimulate endothermic reduction reactions as readily as they do exothermic oxidation reactions. Being a method of achieving "bulk" heating, composites or columns of ore-char blends rapidly heat throughout rather than from the outside inwards as in conventional heating. The microwaves of themselves do not generate any gas - the only gases to be cleaned are the products of reaction in the composites or blends, plus the products of oxygen smelting. In the case of sulphide composites, depending on the quantity and type of low rank coal or char present, sulphur may be eliminated, and collected, in the elemental form. Furthermore, reactions seem to take place at lower temperatures than in conventional smelting but no doubt at the "points" where actual reactions are taking place the atomic or molecular vibrations are such as to satisfy the laws of thermodynamics. Examples are given of the production of unusual products of smelting sulphide concentrates and also the alloys produced from refractory minerals such as chromite and ilmenite. The techniques have been used to produce products with as wide a range of melting points as relatively pure tin and tungsten-molybdenum alloys. Special equipment is being designed and evaluated for these new fields of pyrometallurgy.

Jan 1, 1989

By Erickson M. E, Smith C. K, Carswell J. T

Thirteen holes totalling 3200m were surveyed using a downhole time domain Geonics EM37 system at the 830 metre level within the CSA Mine, Cobar, New South Wales, in order to search for blind, electrically conductive sulphides at some distance from exploration drillholes. A significant off-hole conductor was detected in only one drillhole.Geophysical modelling and interpretation of the survey results indicated that this off-hole conductor was caused by a sulphide lens 30 metres from the drillhole at a hole depth of 220 metres.

Jan 1, 1990

A form of wet pelletization is described where the bridging of the individual particles is achieved by a second liquid phase that pref- erentially wets the suspended solid particles. The phenomenon can be used to obtain efficient separation of solids from carrier liquids, to form spheres from finely divided solid materials, and to separate selected constituents from a body of mixed solids. Typical examples of each of these applications are presented.

Jan 1, 1974

By G Gibson, B Bessen

In coal preparation, large dense medium cyclones (DMC) at low pressure heads (typically 9D where D = cyclone diameter) are the norm. This contrasts with high density mineral applications where, largely for historical reasons, smaller cyclones at high heads are the standard. There are advantages in preferring large diameter cyclones at low heads, assuming that metallurgical performance does not suffer significantly. These include simpler plant layouts, easier maintenance, smaller spares inventories, reduced wear, reduced medium pumping demands, smaller buildings and overall lower capital and operating costs. In 2008, therefore, Xstrata Zinc decided to trial a single DSM-design 800 mm cyclone in one of its four DMC lines at Mt Isa, replacing the four 400 mm cyclones previously installed. Circumstances allowed a low head of 9.5 D to be trialled, compared with the existing 400 mm head of 21.5 D. This paper describes the trial, including tests using painted ore particles as tracers, estimates of yield and metal recovery, and wear monitoring. The larger unit performed well. There was no evidence that metallurgical performance in terms of metal recovery and waste reject rate suffered, and there was some evidence that it may have improved. Cyclone life increased, and preliminary data suggest that the replacement cost of the 800 mm cyclones is less than half that of the 400 mm units, and this is expected to improve. The plant layout and operability have also improved significantly. Xstrata has therefore decided to convert the whole plant to four low head 800 mm units, replacing the original 16 high head 400 mm units. The paper includes an explanation of the effect of static head on DMC separating force. It also reviews earlier research on diamond applications, and applies a general DMC process model to the Xstrata case, both of which confirm that large, low head cyclones are appropriate in mineral applications, contrary to conventional practice. Such units could significantly reduce both the capital and operating costs of DMC plants in mineral applications.

Jan 1, 2009

By Roe P, Lowell A

This paper outlines software development and design work carried out by Mincom Pty Ltd in collaboration with Capricorn Coal Management (CAPCOAL) for computer based design of rehabilitated strip mine landforms at German Creek Mine. Current developments and future application areas for this software are also discussed in relation to other mines in Central Queensland. The development program was initiated in response to statutory requirements placed on mining companies in 1990 to produce a five year Plan of Operations which was to include a contour plan of the final rehabilitated mine landform at the end of the five year planning period. This plan was to be submitted to the Department of Resource Industries (DRI) by 1 December 1990. Due to the limited time given to prepare the plan, a work program was formulated in collaboration with Mincom Pty Ltd to develop suitable software to carry out the design work and provide the required plans and quantities. The software had to include computer based methods to allow design of the proposed landform in line with the rehabilitation strategy adopted by CAPCOAL at the time.

Jan 1, 1991

By Smele J. S, Dawes W. D

In recent years there has been a trend among mining companies to diversify exploration and development away from the countries that have dominated mining activity for the latter half of this century. With some exceptions, this trend is accelerating and is a function of the recognition that many parts of the world, with no previous exposure to modern exploration, are endowed with considerable mineral potential. In addition coincident with changing political and economic circumstances, many countries have recognised the benefits of attracting international mining investment and have radically changed policies, fiscal and legal regimes so as to encourage exploration and mining. Some countries, however, have not readily accepted mining for cultural or social reasons and have yet to make effective changes to mining legislation. For historical reasons, other countries may have little or no direct experience of western economics, nor may they fully recognise the need for stability and competitive fiscal and legal systems to attract foreign investment. Not all ventures in new countries have been commercial successes and there have been some lamentable and recent lapses from grace. Company strategies, company standards and management objectives can also vary widely from company to company. What may be an acceptable risk or rate of return for one may be completely

Jan 1, 1997

The introduction of large diameter holes to underground mining has provided the first opportunity to apply near spherical charges in production scale blasts instead of the convent- ional long cylindrical charges generally used in stope and pillar mining. A modified version of the cratering prin- ciple was applied in the blast design in extrac- ting ore across a horizontal area of a stope or pillar. The new rock breaking technique has developed into the Vertical Crater Retreat (VCR) mining system and eliminated raise boring, slot cutting and dilution of the ore by back- fill material. Furthermore it has reduced labour and time requirements thus becoming not only a low cost method of mining but the safest method of underground mining known today. Exceptionally fine muck is provided with a minimum of damage by blasts to walls and re- treating backs of the stope or pillar. The VCR method can also be used for drop- raising, and for the excavation of underground cavities for almost any purpose . The proper explanation of the breakage mechanism of the near spherical charges opposite to the cylindrical charges yet to be found. The mining industry has quickly recognis- ed the value of the VCR mining method which is being adopted by an increasing number of mines

Jan 1, 1978