Search Documents

The paper describes the design of the dilute medium and medium recovery circuits installed at the coal preparation plants at the Cornwall Coal Company's Fingal Mine, and the BP Coal Australia's Howick Mine. These circuits maximize the use of clarified water for rinsing to improve the mass transfer of adhering medium from the coal surface into the carrying liquid, and have been combined with the use of a two stage magnetic separator. The separator utilizes a conventional concurrent first stage and a counter-rotation second stage. This combination results in high medium recoveries during both normal operation, and start up and shut down phases when large quantities of medium can be lost from a conventional circuit. Overall losses using this circuit have been estimated to be, 200g/t, over a twelve month period. Further advantages in plant operation are also obtained, especially steady operating conditions in the centre-tube pump tank, lower slimes contamination of the product, and lower quantities of non magnetics trapped in the separator concentrates. The techniques are particularly suited to incorporation in circuits treating coals containing high percentages of sticky and difficult clays, as are found in the Walloon coal measures.

Jan 1, 1987

By Aspinall T. O, Loch R. J, Bell L. C

Design of reshaped spoil surfaces is an important pan of rehabilitation of spoil piles resulting from open-cut coal mining. To achieve the optimum design, it is necessary to make accurate predictions of soil losses from spoil piles. Predictions can be based on data gathered using laboratory and field rainfall simulators and field plots. These data are used to derive input parameters for erosion prediction models. Model input parameters include rainfall erosivity, spoil erodibility, sediment size distribution, runoff, soil loss and peak runoff rate. Model outputs can be used in design and include predicted sediment size distribution and predicted soil loss.The traditional method of gathering input data is monitoring field plots. This method is very expensive, must be done on a long-term basis and is affected by irregular rainfall. Long-term field plots are necessary to obtain data that can be applied to empirical prediction models such as the Universal Soil Loss Equation (USLE).

Jan 1, 1992

Blast Engineers frequently use the terminology "the blast showed good heave", or even "the heave was better this time". It is reasonably obvious that "good" and "better" are not the best terms to use. It is also noted that any variation in the data can be misleading. The author proposes a more precisely defined and objective set of measures as tried and tested in a project in 1988. Simple objective measurements of a muck pile profile can measure 1. distance thrown 2. spread of material 3. heaping of material 4. skewness, or bias in the heaping 5. rotation of the mass This technique enables one to compare the profiles from different blasts without relying on subjective experience or judgement. Simple, artificial profiles will be presented to illustrate the problems of description; and then application of the measurement techniques to these profies will be discussed with physical interpretations. The mathematical techniques will be presented, and results of the application of the techniques to real data collected during research carried out at Baimsdale in Victoria, will be presented as illustration. The use of these techniques in mathematical modelling will be discussed.

Jan 1, 1990

By Yianatos J. B

The advances in the study of control alternatives for flotation columns are reviewed. An integral solution to the control problem has to deal with problems associated with instrumentation, process modelling, control strategies and control algorithms. The term hierarchical control is used here to mean the intelligent integration of available knowledge, control algorithms and logic rules of decision. The selection of information, algorithms and rules is based on the experimental and theoretical knowledge of the column flotation process. The software support was designed and implemented in object oriented computer programs. This technique allowed the implementation of a combination of control techniques, algorithmics and heuristics, in the form of a control strategy. This strategy has shown to fit well with processes exhibiting complex dynamic characteristics. The hierarchical control was implemented in a pilot column and included the following general aspects: co-ordination of distributed conventional control loops, use of sets of control parameters for the froth depth control loop according to the froth depth state, verification and diagnosis of sensors, on-line predictive estimation of gas hold-up, diagnosis of common operating problems and the use of predictive control to account for feed flowrate changes.

Jan 1, 1995

By Egan J. R

Changes have recently been applied to the Sullivan Concentrator lead and zinc circuits to treat fine-grained ores which make-up the majority of ore reserves in the mine. Pilot plant testwork conducted in 1990 - 91 indicated that concentrate grades would be substantially improved by reducing the particle size (Pao) of the lead from 38 to 15 ¦m and the zinc from 45 to 24 ¦m. Circuit revisions involved installation of major new equipment including: two 600-kilowatt Vertimills for regrinding, a four metre diametre column flotation cell and a four metre diameter hyperbaric pressure filter for dewatering. Duties of the existing regrind mills were Reassigned.

Jan 1, 1993

By L Keeney

Geometallurgy is not a mechanism designed to replace current geological and metallurgical deposit characterisation but an added component required to understand orebody variability. Current geological characterisation approaches focus on understanding deposit genesis aimed at identifying new mineralised regions and metallurgical characterisation determines parameters required for engineering design of processing plants. Geometallurgical integration has the task of drawing on aspects of each stream to enable spatial mapping of performance indices across a deposit. It is a complimentary activity to current practice and adds a new dimension to orebody knowledge. Although the notion of conducting an integrated geological and metallurgical analysis is not a new concept, limited publications exist in the field proposing integrated methods, with several technical issues existing in current geometallurgical integration approaches. An iterative method drawing on existing geological and metallurgical characterisation and new measurement tools and inputs is proposed. The integrated method comprises of discrete components dynamically linked together through iterative feedback loops with each component having a specific purpose achieved by applying a range of data acquisition technologies and statistical tests. The key outcomes of the method are:overcoming the lack of optimised geometallurgical domains relevant to processing performance,development of a rigorous approach to identifying parameters controlling processability,improved protocols for relevant metallurgical test data and sample selection, andability to generate greater data support to enable rigorous geostatistical modelling of geometallurgical attributes. This paper outlines the integrated mapping and modelling method developed and draws on multiple data acquisition technologies applied within the AMIRA P843 GeMIII Project.

Sep 5, 2011

By P Hatherly, H Gurgenci

With the depletion of the mineral reserves that can be mined by surface mining, demand for highly productive and safe underground mines will increase. Underground drill and blast techniques continue to be refined but true æmass productionÆ is difficult to achieve. As is evidenced by the longwall mining of coal, alternative mining methods based on mechanised mining can meet the expectations but the issues of how to effectively cut strong rocks, how to define the orebody and how the mechanised miners can be automated and maintained all need to be addressed. CMTE is working in all of these areas. We believe that the oscillating disc cutter may provide the long sought-after breakthrough in mechanised rock cutting. Disc cutters are one of the most robust designs of cutting tool and the cutters attack the rock in a manner which effects direct tensile breakage. The internal cutter drive and the inertial damping mean that the already low cutter forces are not all transmitted back to the machine, making it possible to design lightweight, flexible mining systems. For orebody delineation drill monitoring, drillhole logging and geophysical imaging are key procedures being developed at CMTE. To automate mining machines, work is progressing well in the development of systems for autonomous vehicle navigation and mining robotics. A strategic contribution to maintenance issues is being made through the development of procedures for automatic analysis of used oils, monitoring the strength of mechanical structures, and operating point optimisation.

Jan 1, 1998

By Kentwell D. J, Cusak C. J, Harvey-Kelly F. E L, M D. Goodz

The Morning Star Gold Mine presents an example of a prolific operation with considerable historical records, mine workings, drill hole logs and countless plans from greater than 20 adjacent mines which have now been consolidated to form the current project. Implementation of 3D computer modelling in the planning stages has provided an additional tool to integrate and refine geological models as a guide to some exploration strategies. It has allowed for a re- interpretation of the host rock units, dimensional constraints, new exploration extensions and provisional resource modelling. The initial consideration of this project was to integrate 135 years of mining history into a single database. Each historic mining area had an unrelated mine grid, often established parallel to the long axis of their main stopes; some were based on magnetic or true north. Survey plans were in chain, imperial or metric units. Through the manipulation and rotation of old grids, previously unrelated mine workings began to form continuous mineralised zones, with unmined portions still remaining in between the existing development. Furthermore the current drillhole database of >433 holes showed numerous confirmatory intersections of new mineralisation. A series of tiered tables were created within a relational database to derive guidelines for assessing data to attribute a Mineral Prospectivity Value [MPV] based on key indicators of mineralisation. Indicator logging now forms the basis of geological descriptions.

Jan 1, 1997

The continuous casting of zinc alloys has been of fundamental importance for many years in the production of a number of products, including sheet for architectural applications, battery cans for dry cells and wire for metallising. The intrinsic benefits of continuous casting, including efficiency and high tonnage capability, uniformity of metallurgical structure and properties, and absence of voids and other defects, have contributed to the success of these products. Less well known, but of growing importance, is the more recent application of continuous casting technology to the production of zinc alloy bar stock products, including bearing stock, machining bar stock, forging stock and cathodic protection anodes. A wide range of zinc alloys are now continuously cast in a variety of cross sectional shapes and sizes to suit the diverse characteristics of these products. Of particular significance are the introduction of hollow zinc-aluminum bearing stock, and the availability of zinc alloy machining bar stock for hydraulic applications and for producing prototypes of zinc alloy pressure die castings. In addition to the traditional benefits, continuous casting provides special properties which are important in the application of these bar stock products. The list of successful applications of continuously cast zinc alloy bar stock is growing rapidly, and the market potential for resultant new zinc applications appears to be significant.

Jan 1, 1993

By Large RR

Underlying the 15 million tonne, high grade Hellyer volcanogenic massive sulphide deposit of western Tasmania is an extensive, well developed, and well preserved stringer system. Pervasive alteration of the footwall mafic volcanics occurred as the hydrothermal system initiated. Mineralogical zoning exists within the footwall alteration pipe, with a central siliceous core giving way to zones of chlorite, chlorite-carbonate, sericite-chlorite, and finally sericite-quartz on the margins (stringer envelope zone). However, the alteration morphology and zonation is not symmetrical around the central siliceous core; eastward the alteration zones are steeply dipping and terminate abruptly under the massive sulphide, while westward they extend out under the ore body in a blanket fashion. Geologic evidence indicates that the pervasive alteration started with the development of sericite-quartz which was subsequently overprinted by chlorite and finally quartz-sericite as the hydrothermal system became focused towards the centre of the stringer system.

Jan 1, 1990

The need to schedule ore production to make maximum use of the strength gained by cem- ented fill during curing is discussed, to show how cement content and hence fill cost can be kept down for any particular operation. Results from laboratory testwork on Isa Mine fill conducted by the author while employed by Mount Isa Mines Limited form the basis of the Discussion

Jan 1, 1973

An empirical method of estimating dense rock (D.R.E.) equivalent volumes erupted as airfall tephra, described in a companion paper in this volume, is elaborated, and its accuracy discussed. Estimates obtained from a single eruption can be classified as to whether they show positive, negative, or constant relative dispersion. For positively dispersed tephras (estimated volumes increasing with distance), this procedure improves the accuracy of the method. The technique is applied to selected andesitic tephras erupted from Egmont Volcano, New Zealand, during the last 28 000 years, which are found to range in volume from about 1.5 x 107 m3 up to about 2.4 x 108 m3 D.R.E. With a factor of about 16 between the smallest and largest volumes, this contrasts sharply with the rhyolite volcanoes in New Zealand, where the difference factor is usually of the order of 100. The largest tephra eruptions at Egmont are small compared to the largest debris avalanches, which have exceeded 1010 m3 (10 km3) in volume.The magnitude versus frequency relationship, calculated using a maximum likelihood method, establishes the limits of eruption magnitude at Mt Egmont as 107 to 109 m3 D.R.E. For some volcanoes, the magnitude-frequency relationship changes with time, owing to clustering of eruptions, separated by long dormant intervals. Ngauruhoe Volcano, New Zealand, is an example. Within eruptive episodes, the mean interval between eruptions of >_ 105 m3 is about 0.9 ¦ 0.65 years. The mean interval between eruptive episodes in which >_ 106 m3 is erupted, including episodes in which this volume is erupted gradually, is about 25.8 ¦ 6.6 years, and the mean dormant interval between all episodes is about 5.2 ¦ 3.0 years. At present Ngauruhoe is in an unusually prolonged dormant period, 50% longer than any in the historical record, since 1839.

Jan 1, 1990

By Wright G. A

The objective of refining in steelmaking is to reduce the concentration of impurity atoms, e.g. sulphur, phosphorus, from an initially high level to a specified low concentration. A two-film theory of refining is presented in which the rate of

Jan 1, 1980

By D Caffrey

To demonstrate the advantages of using electronic delay detonators over pyrotechnic detonators, a trial using the DNES Dynatronic System was conducted at the KCGM Mount Charlotte operation in 1998. The trial clearly demonstrated that accurate control over the firing delay time between blastholes can lead to fragmentation improvement and ground vibration energy control which are two important issues for the Mt Charlotte underground operation. Excellent fragmentation was achieved by employing a 12 ms delay sequence. Detailed fragmentation analysis has shown a 10 to 20 per cent passing increase for the rock fragment size from 0.1 to 0.4 m compared with the pyrotechnic detonator firing. There was no increase in ground vibration level on the surface with the electronic detonator firing even though the electronic detonator firing had a much shorter blast duration than the pyrotechnic detonator firing. In fact, our energy calculation has clearly shown that much less energy had been propagated to the surface from the blast using electronic detonator firing.

Jan 1, 1999

By Haskard R. W

A method of raising has been developed at Cobar Mines Pty Ltd's CSA Mine which has achieved advance of up to 6 m in a single blast and raises are now developed which have averaged 4.2 m per blast. The method is a form of Long Hole Raising and is applicable to short raises of less than 50 m length. Blast holes are column charged and initiated sequentially with short delay detonators (millisecond). The equipment used to drill the raising blast holes consists of normal production drilling rigs and accessories and no other special equipment is required. The method has significant advantages in rates of performance and fits neatly into production drilling and blasting schedules. The method is also far safer than any non-mechanical or conventional means of Raising.

Jan 1, 1983

By A Sinuhaji, H Kalangi, T B. Setyoko

Ore fragmentation at the DOZ block cave mine is highly variable, both as a function of rock type and column height of draw. Initially, the mine was constructed and equipped with limited capability to handle drawpoint oversize material. Significant issues with drawpoint availability and achieving overall mine production targets resulted. A suite of secondary sizing tools was added to the mine equipment fleet over a one-year time frame. Although significant oversize continues to be experienced, use of the correct secondary breakage tool for each particular oversize or hang-up occurrence has resulted in increased drawpoint availability, production rate, draw compliance, and operator safety. Currently, a range of secondary breakage techniques is being utilised to size material for delivery to the primary crusher. Run-of-mine material (3) is directly mucked to ore passes fitted with grizzlys that have one-metre square openings. Ore containing small boulders (>1 m3, 3) is loader-trammed to ore passes fitted with rockbreakers. Medium-sized boulders (>2 m3) accessible from the drawpoint are drilled with Sandvik Tamrock Commando drills. Boulders hung-up within the drawbell are drilled and charged with a Sandvik Tamrock Secondary Breakage Unit. Compacted, fine-grained muck is blasted utilising 55 mm cartridge powder concussion bombs.

Jan 1, 2005

The South Junction deposit of St Barbara Mines Limited was discovered in 1989 by the geologists of Ross Atkins Mining.The deposit occurs in the lower part of the Gabanintha Formation of the Lukes Creek Group in the Mt Magnet -Meekatharra greenstone belt. Country rock is predominantly talc-chlorite schist. Gold mineralisation is associated with north-south shear zones, quartz-carbonate-fuchsite alteration of the ultramafic rocks and in particular close to deeply weathered quartz-albite porphyry. For a detailed description of the geology of the South Junction Deposit see Fiala (1992).

Jan 1, 1993

By J Rayner, R P. Langmead, J A. R Coote

Gosowong is situated within the Neogene magmatic arc of Halmahera island in the Maluku province of eastern Indonesia. It was discovered as the result of a rigorous ground reconnaissance program in an area with no previous mining activity. The broad structural setting in the Gosowong District comprises an elongate dome formed by the forceful upward intrusion of magma along a deep-seated structure, resulting in associated tensional fracturing trending parallel to the long axis of the dome. Four copper-gold porphyries and numerous low-grade epithermal veins occur within this mineralised corridor, with the Gosowong Deposit being the only economic occurrence discovered to-date. Gold mineralisation is hosted within multiphase epithermal quartz-adularia and quartz-chlorite fissure veins, breccias, and stockworks. High-grade gold mineralisation is emplaced in two gently south-plunging ore shoots along a 400 m section of the north-striking, east-dipping, Gosowong Fault, the primary control on mineralisation. The Gosowong Fault is believed to be a tensional fracture associated with uplift of the dome. Lithological variation and structural intersections play a large role in grade distribution within the vein zone. Host rocks comprise a wide range of shallow marine, intermediate-basic volcanic and volcaniclastic rocks of ?late Miocene age. The Gosowong gold deposit is a classic example of a low-sulphidation epithermal gold deposit, based on the abundance of adularia and illite in the alteration assemblage, and low base-metal sulphide content within quartz-adularia veins. The indicated resource is estimated at 0.99 Mt at 27 g/t Au and 38 g/t Ag for a total of 870 000 ounces Au, using a cut-off grade of 2 g/t Au.

Jan 1, 1999

ILZRO sights are locked securely on the targets of the expanded applications and ever-improving quality in the major market for zinc-coated steel. A wide range of ILZRO-sponsored research projects examine issues of formability, paintability, and corrosion resistance for traditional hot-dip galvanising, electrogalvanising, and ILZRO's own proprietary zinc coating, Galfan. Recent research has focussed on the on the interaction between Galfan and different substrate steels to determine optimum combinations for different applications. ILZRO enjoys an evolving role in providing the connection between research laboratories and marketing divisions through supporting research and services for the Galfan Technical Resource Centreò(GTRC) and the recently formed North American Galfan Development Authority (NAGDA). GTRC has just produced a new problem-solving manual that provides a comprehensive source of hands-on solutions for the many Galfan licensees throughout the world, and should contribute substantially to the reputation of Galfan as a consistently top-quality steel-coating product. Meanwhile, NAGDA is advancing the market with new advertising for Galfan based on superior corrosion-resistant qualities proven through ILZRO-sponsored research. Practical manufacturing issues remain at the forefront of ILZRO priorities, with research emphasis on cutting and welding zinc-coated steel to provide direct assistance towards improved product quality and a more secure market. Moving to the arena of die casting, when the specifier looks to zinc to fill a design need, ILZRO-sponsored research projects provide comprehensive documentation on metallurgical characteristics for every zinc alloy under almost any imaginable application. On-going ILZRO-sponsored research is integrating this wealth of data with sophisticated computer programs that model die-casting designs with ever-increasing accuracy, as other ILZRO projects lay the market groundwork for zinc in applications ranging from vibration damping to electromagnetic shielding.

Jan 1, 1993

By Burford B. D, Johnson N. W, Rohner P

Under design philosophy, the Hilton concentrator produced lead, zinc and LGM (lead plus zinc) concentrates. The LGM (Iow grade middling) concentrate was produced by combining coarse middling streams from the lead and zinc circuits, regrinding and subsequent flotation. Mineralogical examination of the zinc circuit middling stream prior to regrinding suggested that production of zinc concentrate from the zinc circuit middling stream should be possible by rearranging existing plant equipment. Laboratory testing of samples of plant products, however, showed that regrinding combined wi th the usual reagent suite was nO1 sufficient to produce a zinc concentrate of the required specifications.Examination of the process water highlighted a problem with dissolved salts in the circuit water, which was solved by in-circuit precipitation of the dissolved ions with soda ash. Implementation of the procedure in the concentrator effectively transferred to the zinc concentrate all sphalerite previously recovered to the LGM concentrate.

Jan 1, 1994