Search Documents

The explosion at Appin Colliery on July 24th, 1979, demonstrated the need for a large scale facility to simulate an underground type explosion and study its effects. The effects of an explosion cannot be established quantitat- ively using small scale models. A gallery was constructed for this purpose at Londonderry Centre and commissioned in Feb- ruary, 1980. It is 50 metres long, 2.7 metres in diameter, capable of withstanding an internal pressure of 210 kPa and is the only facility available for this purpose in Australia. The gallery has provided valuable inform- ation on blast effects of explosions in tunnels and is to be used for testing the performance of explosion arresting devices, further invest- igation of explosion effects, research into basic explosion phenomena and instrumentation development. Additionally, it will provide a demonstration facility for training purposes.

Jan 1, 1981

By G Bournival, Y Pan, S Ata

A custom-made set-up that measures bubble coalescence time and the thin film balance (TFB) technique were used to explore the role of residual xanthate (potassium amyl xanthate, PAX) and salt (NaCl) on the adsorption of two frothers (methyl isobutyl carbinol-MIBC, and di-propylene glycolDPG) at the air-water interface. This paper is primarily focused on the comparison of these two techniques in studying the interaction between the flotation reagents and salt emphasizing their capabilities and limits. The results from the coalescence rig showed that the presence of PAX improved the stability of bubbles in both frother solutions and led to a bubble coalescence inhibition at 50–500 ppm DPG. These measures were compared with the results from the TFB. Findings from the TFB were overall in good agreement with the bubble coalescence time, but a higher stability level was observed in thin films under the same condition. The effect of salt on the frother and PAX mixture was also explored, and the results showed an adverse impact of the salt on the interaction of frother and PAX with both techniques. However, variations were found between them in some cases. The TFB is much more sensitive to the presence of dissolved gas and oil droplets.

Aug 24, 2022

By A G. L Pratt, M S. Kemp

BHP has used many innovative techniques when recruiting its workforce for the Cannington Project. Looking for a balance of experience and enthusiasm it was necessary to develop pre-selection tests to reduce the initial number of applicants to a manageable number for first interviews in Townsville. Success at this stage led to an applicant, and their spouse, to go through a second interview at the mine site. The full process from application to job offer took up to six months, but the results were felt to be worth the effort. The approach taken has resulted in a highly motivated and flexible workforce. This paper outlines the philosophies behind CanningtonÆs recruitment process, highlights some of the issues associated with the approach, and offers some measures of the outcomes.

Jan 1, 1998

By D E. Thorp

The mining and concentration operations of New Zealand Steel have been carried out initially from the Waikato North Head (WNH) deposit since 1969 and subsequently from the Taharoa deposit since 1972. Over the years the WNH operation has produced about 1.2 million tonnes of concentrate which has been converted into steel, while total exports to the Japanese Steel Industry from Taharoa reached five million tonnes in February of this year. Recent expansion plans both in domestic steel production and in the ironsand concentrate export market have made it necessary for the company to look closely at, among other areas, the mineral processing of the titaniferous ironsands in both deposits. This paper deals with the recent test work carried out at WNH and Taharoa on the use of the cone concentrator unit as a primary gravity concentrating unit ahead of the magnetic separation stages and as a cleaner concentrator following the primary magnetic separation.

Jan 1, 1977

By Duniam P

Sequencing of large underground firings is a critical aspect of blast performance. Using theory developed in open cut operations, where blast results are easier to quantify, a new technique for sequencing underground mass blasts has been developed. The basis for the technique is to identify timing regimes to control fragmentation and relief then apply non-electrics to fit these criteria. The use of computer software to graphically interpret delay statistics enables the evaluation of designs in a realistic manner.

Jan 1, 1995

By T Weldon

In the last 15 years, it has become increasingly popular to win gold and silver from carbon strip solutions with electrolytic æsludgeÆ cells. The precious metal sludges produced in the cells are washed to the cell bottom and pumped into filters. Most new operations are specifying sludging cells, and many older operations are being retrofitted with up-to-date electrolytic sludge cells and filters. The new sludging cells are generally more energy efficient than older cells, but more importantly, the cell operations to remove product are much less labour intensive, cleaner, and the operator need not have physical contact with the electrolytically produced metal. A case study of a major North American gold producer (50 000 kg/yr) that removed old style stainless steel wool cathode cells and installed new sludging cells and sludge filters is presented. The effect of various impurities is discussed.

Jan 1, 2005

Pike River Coal Limited is in the process of developing the Pike River Coal Mine in the Paparoa Ranges of New ZealandÆs South Island. The mine will be developed to extract a coking coal deposit of the Brunner Seam, some 46 km north-east of Greymouth, using a combination of continuous miners and hydraulic extraction. The mining area is located within Department of Conservation (DOC) land and is adjacent to the escarpment of the Paparoa Range and the Paparoa National Park.   As such, the major restriction to planned extraction is protection of: +        the western escarpment, +        vertical and sub-vertical rock faces, +        permanent water courses, +        significant vegetation, and +        steep slopes.   The mine will use its elevation advantage to hydraulically flume coal from the working faces to the pit bottom area where it will be slurried to approximately 35 per cent density of solids and pumps down a slurry line to the coal prep plant some 10.5 km down the Pike River Valley. The coal will be sold on the export market as a high quality coking coal for international steel making.

Jan 1, 2006

Ore textures in Australian BIF-derived ores are quite complex and have formed the basis for ore genesis models, which includes hypogene upgrading or supergene upgrading then regional metamorphism for the microplaty hematite ores and supergene upgrading for the martite-goethite ores. Despite a high level of ore texture knowledge, little is known about the spatial distribution of ore textures within deposits or their relationship to downstream processing. This paper describes a new iron ore texture classification system to better understand the vertical textural zonation characteristics of Australian BIF-derived deposits, the interpreted role of recent supergene upgrading processes on modifying primary ore textures and their implications for downstream mineral processing. The iron ore textural classification scheme presented uses textural groupings defined on the basis of similarities in mineralogy, ore texture, porosity, mineral associations and hardness. The scheme is non-genetic and has been successfully applied to deposits in the Pilbara, Yilgarn and Gawler cratons. The main ore texture groups include dense martite/hematite, microplaty hematite, microplaty hematite-goethite, martite-goethite, goethite-martite and goethite-rich. Each group can be further subdivided into physically hard to softer subcategories. The ore textural groups can be divided into those interpreted to be associated with primary replacement of BIF and secondary textures resulting from more recent modification by near-surface hydration or dehydration processes. A schematic vertical section through BIF-derived deposits consists (from surface) of detritals underlain by a carapace, both of which may have been eroded, followed by a hydrated zone with replacement of primary ore martite and microplaty hematite by vitreous goethite. The hydrated zone is underlain by 0.2 - 6 m thick zones of intense dehydration and textural infilling of porosity with hematite and hydrohematite. Immediately below the dehydration zone is a strong zone of leaching, where more porous and friable ore textures occur, followed underneath by a gradational contact with primary ore. Secondary supergene processes can impact on beneficiation with hydration and leaching resulting in more difficult density separations at the concentrator stage due to reductions in density differences between ore and gangue and loss of heavy media into pores. Supergene modification of primary BIF-derived ore textures can substantially change lump metallurgical properties, with hydration and dehydration favourably increasing lump yield but reducing resistance to thermal shock whilst leaching will give the opposing outcome. The lump properties of ore textural groups appear to be relatively consistent within and between the iron ore deposits examined.

Jan 1, 2002

By Restarick C, Jowett A

A cylinder-cyclone system, fitted with a flow control valve between the cylinder and cyclone plus in some tests a variable cyclone spigot, has been used to achieve classifier separations at unusually coarse sizes relative to the diameter of the units used. The method has proved to be useful for low tonnage flows at low pulp density and variable feed rate. The system relies on use of a cylinder unit to reject excess water and fine particles, the amount rejected being adjusted by the flow control valve. The valve also adjusts flow rate and pulp density of feed to the cyclone unit, and can be adjusted to give a separation at a coarse particle size. The system has been used in connection with experiments on the pilot plant at Mount Isa, where a 76 mm system was used to classify feed to the lead secondary rougher circuit at sizes as coarse as 52 micrametres galena equivalent for split conditioning tests. Further tests have been carried out with quartz to assess the range of size separations Possible.

Jan 1, 1978

By S Jayakumari, E Ringdalen, V Canaguier

Silicomanganese (SiMn), containing approximately 16–30 per cent Si, is produced in submerged arc furnaces using various Mn sources and quartz as the primary raw materials, along with fluxes and reductants. In the high-temperature zone known as the coke bed, a silica-rich slag is formed. SiMn is produced through the reduction of SiO2 from the slag. Dissolution of quartz into slags with different compositions, the primary slag formed from the Mn sources and flux before any MnO reduction occurred, representing conditions at the top of the coke bed, and dissolution of quartz into a partially reduced slag to simulate conditions inside the coke bed has been investigated. Experimental investigations were carried out to study the dissolution of quartz particles of varying sizes, 5 mm and 25 mm in synthetic slags with different compositions at temperatures between 1400°C and 1600°C, with varying holding times. Observed results are compared with liquidus compositions and equilibrium phases for original and formed slags. Particle size has been shown to be of little importance for the dissolution. Quartz dissolved more easily in slag at top of the coke bed than slag in the coke bed. Complete dissolution was observed after 30 mins at 1600°C in all cases, but not after 0 mins.

Jun 19, 2024

To finalise the arrangement and details of the headframe to be erected over the new No. 3 Shaft, the haulage and winding equipment requirements were first determined, then tentative designs were prepared to cover the needs of general shaft servicing work for men and materials, mullock and ore handling, and the probable requirements of a breaker station to be built adjacent to the headframe, which would provide for the crushing of the run-of-mine ore down to a size which would be suitable for feeding on to the concentrating mill.

Jan 1, 1957

The exposed high face of Kerr's Quarry has dominated the township of Ferntree Gully for half a century. The near perpendicular face of bare dacite rock is a crumbling scar in an area of significant natural beauty. Apart from being unsightly, the face is a hazard for any person who approaches too close to its base or to the top edge. The height and the precipitous nature of this man made wall of rock is hazardous indeed. (fig. 1) The rock face is on the municipal boundary between the Shire of Sherbrooke and the City of Knox. This boundary was drawn when partition of the Shire of Ferntree Gully took place. There are many advantages in benching back the wall of the quarry but to do so the operation, located in Knox would need to extend into Sherbrooke. There are planning difficulties involved in such a manoeuvre, but during 1972, at a meeting of Cabinet Ministers, it was agreed that the matter be resolved.

Jan 1, 1976

By Coates D. F, Neil T. J, O&apos

A proper economic analysis of pit slope design must reflect the trade-off between the benefits and the increased risks of slope fail- ure inherent in steeper slope angles. However, no formal framework for a proper analysis existed to date. This paper describes the results of the past four years' effort in which a formal eco- nomic analysis framework was developed and tested through a case study. This framework, in essence, consists of the availability of tested procedures and com- puter programs. The procedures as well as the programs are divided into two broad functional categories; (1) the first category related to assessing the economic benefits and costs associated with various pit slope angles and (2) the second category that determines the overall financial impact which the assessed benefits and costs exert to the mine operator's overall economic stature.

Jan 1, 1977

By Pak DL

Over the last decade computers have become an essential element in assessing the economic feasibility of mining new mineral deposits and in assisting a variety of related support functions. A broad overview is given of the many technical application areas where computers are contributing to the mining industry with reference to work being done on the evaluation of drill hole information, mineral inventory modelling, ore reserve estimation, financial analysis, process simulation, process control, workshop job scheduling, PERT applications, and com- puter aided drafting. In all these areas the computer has greatly reduced the manual effort involved in looking at alternatives. It has had a significant effect in eliminating delays in revising calculations, or rescheduling activities to incorporate new data or cater for changing conditions, while at the same time providing more accurate and prompt information for the management decision making Process.

Jan 1, 1980

By Moritz P

Thiourea has been recognised for a long time as an acid-stable complexant for gold. Generally, the use of thiourea has been shown to exhibit enhanced leaching kinetics compared to cyanide but suffers the disadvantage of excessive reagent consumption. Thiourea leaching is particularly com- patible with the extraction of gold from refractory ores. This is due to the need for an oxidative pretreatment to liberate the gold. Such pretreatments typically result in the production of an acidic residue. The application of novel thiourea leaching technologies to the extraction of gold from a bioleached pyrite concentrate was investigated. The interac- tion of leach variables with thiourea consumption and gold extraction was established. An economic assessment of thiourea leaching was compared with conventional cyanidation. The results indicated that gold leaching of the bioleached residue using thiourea compared very favourably with cyanidation.

Jan 1, 1991

By E R. Ramanaidou, M A. Wells

Asian steel mills are demanding iron ore with specific chemical, mineralogical, metallurgical and environmental properties to warrant that the ore is of the greatest quality. As a result, a toolkit of analytical techniques becomes important. Hyperspectral analyses of iron ore cores and chips using a HyLogging™ system are now routinely undertaken by BHP Billiton Iron Ore in Western Australia for banded iron formation-hosted iron ores and channel iron deposits to better characterise their iron ores. Objective information can now be expanded by adding new sensors. The current HyLogging™ system provides point analysis reflectance spectra and a red–green–blue high-resolution image, while recent developments, such as hyperspectral imaging using the Corescan system, now provide full spectral image and surface topography. The addition of Raman spectroscopy provides the ability to detect and quantify quartz and magnetite (or maghemite) and cross validate hyperspectral information on hematite and goethite and aluminium substitution in the iron oxides. Micro-X-ray fluorescence mapping also adds chemical information appropriate for cross validation with the aforementioned methods. This paper demonstrates the value of combining these techniques for an optimum characterisation of iron ore.CITATION:Ramanaidou, E R and Wells, M A, 2015. A new toolkit for iron ore characterisation, in Proceedings Iron Ore 2015, pp 587–590 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Hutchings SG, Skimmings T

This paper describes the results of the field application tests at Miike Colliery on the integrated automatization of the longwall mining system for medium thick coal seam. The purpose of the research is to develop an automatic longwall mining system which can be controlled accurately from outside of the face, and the ultimate goal is an eliminate of men from the face. Presently, the field test is being conducted in Yotsuyama mine following to a success in the performance test on surface. Remote Batch Control System for shield supports has been adapted to operate all supports from the control panel located at the entrance of the face. Remote monitoring and control system of the drum shearer has also been tested. The system makes it possible to operate the shearer either at the main gate or full automatic. Productivity and safety will be substantially improved as those systems enable to eliminate all workers from the face under the severe working conditions with high ground pressure and hot and humid atmosphere due to increasing mining depth. So far, we have been satisfied with the results of the field test and those system will be an effective countermeasure to operate the face with a high risk of rock-burst.

Jan 1, 1987

The paper describes developments since 1959 in major excavators to meet the demand for higher outputs of overburden and coal under less favourable batter conditions than used hitherto in the coal deposits of the Latrobe Valley. Particular reference is made to investigations of designs of bucket wheel head configurations for the digging of these flat batters on high faces, and examples are given of the wide use of models inthese studies. An explanation is given of how solution of these problems and surface conditions unfavourable for wheeled transport confirmed selection of the long boom rather than the compact type of bucket wheel excavator for the Latrobe Valley applications.The past decade has seen advances in the manufacture in Australia of components for excavators and similar machines. The history of Australian manufacture of components for major brown coal excavators is traced;and reference is made to study and application of Australian and overseas (mainly German) codes and practices in the design and construction of machines made partly here and partly in Germany.A section of the paper deals with advances in electrical engineering for large excavators in Australia and its interdependence with mechanical design and construction.Finally, as an example of the versatility of the bucket wheel excavator, a description is given of a recent application for the mining of mineral sands in northern N.S.W.

Jan 1, 1971

By J Arif, J Proffett

Copper and gold mineralisation at Batu Hijau is directly related to quartz veining and wall rock alteration that developed in close spatial and temporal association with multiple tonalite porphyry intrusions. To its advantage with respect to the study and better understanding of the evolution of the porphyry system, Batu Hijau has comparatively minor late alteration and mineralisation overprints. This paper summarises results of detailed geological logging, petrographic studies and geochemical analyses of diamond drill cores from the deeper sections of the Batu Hijau porphyry system (ie its roots). An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By Y M. Wang, W Z. Liu, L F. Li, X L. Zhang

Based on the blasting crater theory, the equation between k under typical cases and burden line, charge height was obtained by open pit bench blasting analysis model. The model was calculated with mine production blasting. The blastability coefficient k and the best range of blasting burden line were specially emphasised on determination of lateral crater tests.CITATION:Wang, Y M, Liu, W Z, Zhang, X L and Li, L F, 2015. Application of lateral crater test in open pit blasting parameters optimisation, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 463–468 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015