Search Documents

By A Winchester, D Grant

The massive 1100 Orebody in Mount IsaÆs X41 Copper Mine has been extracted over the last 40 years form north to south utilising sublevel open stoping methods.De velopment has continually stepped ahead of production to provide access to new primary stoping blocks. The remaining secondary pillars contain stopes with one, two or three fill mass exposures and were constrained by access requirements and stope extraction turnaround time.The remaining southern mining areas consist of large 40 m wide by 300 to 400 m long east-west transverse pillars that have been left to provide access for ventilation and service requirements. Three large transverse cross-cuts or transverse pillars û 4180 x/c, 4010 x/c and the Panel pillar now remain. The 4180 x/c was the last major transverse pillar to be successfully broken.This transverse pillar is being extracted in a retreating sequence, creating 3SLOS stopes due to the surrounding backfilled stopes.In recent years the extraction of the first, and most critical, stopes in the transverse pillars have resulted in large changes to the induced stress field. This paper describes the extraction of the 1.1 million tonne stope P418 in the 4180 x/c pillar.T echnical challenges that were faced and how they were overcome to allow for the successful extraction of the stope are described.Critical to the success of the P418 stope extraction were the rehabilitation methodology used; extraction strategy modifications to address deteriorating ground; mass firings with multiple directional changes; managing the exposure of backfill of variable strengths; and geotechnical monitoring prior to, during and after extraction.

Jan 1, 2005

By K Ellis, B Lumsden

A full-scale statistically-based on/off plant trial of a new flotation conditioning technology designed to improve fine mineral recovery was undertaken to determine whether the recovery of selected fine sulfide minerals can be increased. The technology is selective for certain sulfide minerals only, including chalcopyrite and sphalerite. The technology has been shown to selectively aggregate the fine chalcopyrite and sphalerite minerals giving increased flotation recovery. The plant trials have shown an increase in the mineral recovery, without decreasing selectivity. Size by size recovery shows a significant increase in the fine (

Jan 1, 2005

The Managalase area is remote and little visited by geologists or prospectors. Yet it holds the key to the tectonics and petrology of this part of Papua. The eastern Managalase plateau (M, Figure 1) lies between the Hydrographers andesite volcano (H) and Sesara shoshonite volcano (S) to the south of Popondetta on the Papua Peninsular. It contains over 30 small volcanic centres in an area of only 400 km2 . To the south and west lies the basic-utrabasic belt (B-UB) of the Morobe arc. This is the leading edge of oceanic plate obducted over the Owen Stanley Metamorphics during the lower Eocene time. To the east and southeast lies the Cape Vogel geosyncline where the western end of the Woodlark basin spreading centre enters mainland Papua. The extension of the spreading centre as a suture might pass as far as the southern margin of the Musa Coastal plain. A new pattern of plate tectonic motions has been determined by the global positioning system and the southern margin of the Woodlark plate has been redefined (Tregoning et al, 1998; Taylor, Goodliffe and Martinez, et al, 1999). The Managalase plateau is margined by two inferred faults. These outline a cusp protruding from the main basic-ultrabasic belt where these rocks are near the surface. The westerly arm of the cusp passes through the centres of the Hydrographers and Mount Lamington andesitic volcanoes. Mount Lamington overlies Quaternary alluvium and underlying Tertiary sediments (Arculus et al, 1983) but members of the basic-ultrabasic belt crop out on the southern flanks. The easterly arm of the cusp is an inferred shear zone (and ? fault) connecting up with the terminus of the suture on the Musa coastal plain. Movements on the two faults forming the cusp are thought to have produced the conjugate N-S, E-W faults on the plateau (Ruxton, 1966). To the east, and isolated, are the two large andesitic stratovolcanoes of Mounts Victory (V) and Trafalgar (T) which together form Cape Nelson. Mount Victory was last active in the 1890s. The Waiowa shoshonitic volcano explosion centres (W), last active in 1943 - 1944, lie near the suture adjacent to the actively rising Goropu mountains. Extension in these mountains is clearly demonstrated by the soil profiles being skeletal along a bounding fault and ageing uphill. The incision of small parallel ravines also dig deeper further upslope from the fault. To the south-east of Mount Suckling (K) the Dayman Dome is also an expanding mass. The Owen Stanley fault is parallel, and located to the south of the suture. The Mesozoic metamorphics form the backbone of the Papuan Peninsula. The intramontane Musa Trough is thought to date from the mid-Tertiary. At the eastern end of the trough Pleistocene and Recent ultrabasic breccias and alkali basalt crop out (Green, 1961).

Jan 1, 1999

By X Li, J Wang, D Liu, Y Liu, K Hu

"Since the adoption of open-door policy 30 years ago, rapid economic growth has resulted in serious resource depletion and environmental destruction, especially in mining areas. As an urgent response to this situation, the central government and the Ministry of Land and Resources (MLR) have adjusted policies with concrete and realistic actions for halting this trend of non-sustainable mining activities in China. æGreen Mine CampaignÆ is one of the actions implemented. In 2010, MLR announced the æGreen Mine CampaignÆ, in which existing and new mines will be evaluated against the æGreen Mine Construction StandardsÆ and certified as æGreen MineÆ if complying with these standards. The standards cover five key aspects: the considerations of science-supported resource exploitation efficient resource utilisation standardised management environmental friendliness harmonious community relationship.Every year, MLR reviews ægreen minesÆ from all provinces. Thirty seven mines, including coal, metal, non-metal, gold, chemical industry and building materials mines, passed the review and were certified as green mines in 2010. In 2011, 187 out of 194 mines that participated in the review were certified as ægreen minesÆ. These mines are viewed as good examples of sustainable mining development in China.CITATION:Liu, Y, Hu, K, Li, X, Liu, Y, Liu, D and Wang, J, 2012. The green mine campaign and sustainable mining in China, in Proceedings Life-of-Mine 2012, pp 339-342 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 10, 2012

By M Spiteri, S Woth, J Caratti, K Henley

Blasting is an essentially violent process aimed to disrupt and loosen rock for productive excavation and downstream processing. Dilution of the orebody to some extent is the inevitable result, particularly in narrow vein gold mines. A small change in gold recovery is usually a strong lever on revenue generation. As a result blast designs are carefully engineered to both minimise and control the direction of rock movement. Traditionally blast designs in gold mines have used the minimum powder factor that will still permit rock excavation. This now conflicts with the recent industry trend to optimise the total process flowsheet from the mine to the mill. Numerous mines have achieved success in reducing total mining cost by increasing powder factors. Not only is explosive energy cheaper than mechanical comminution energy requirements, the increased blasting effect may deliver benefits across all downstream processes of digging, hauling, crushing and milling. Kalgoorlie Consolidated Gold Mines (KCGM) Fimiston operation is the largest gold mine in Australia, located in the heart of the Kalgoorlie Goldfields. Blast dilution has been reduced at KCGM by managing location of blast boundaries and by firing along strike to choked faces. Significant economies of scale have resulted from application of a bulk mining methods. The bench height of 10 m is the largest in the Western Australian Goldfields, and is typically mined in a single pass with large face shovels. Recent increases in production rates in both the mine and mill has been partly attributed to a 30 per cent increase in powder factor. KCGM then examined the benefit of a further 18 per cent increase in powder factor to 1.0 kg/BCM. A concern though was the impact of very high powder factors resulting in excessive blast movement and subsequently ore dilution. This was the subject of a project conducted with Orica Explosives. OricaÆsDMC(Distinct Motion Code) blast model was applied to understand the effect of not just further increases in powder factor but also blast geometry and explosive type. The modeling work demonstrated that high powder factors may be applied with minimal increase in ore dilution provided the combination of blast geometry and explosive type is optimised. These results are currently being implemented to achieve further reductions in total mining costs without a significant impact on recovery.

Jan 1, 2001

By A Huebner, A Noack

Companies all over the world are very sensitive concerning their IT and network security. In most network connected technical installations and machines however, network security is not taken into account to a significant extent: insecure protocols are run, unencrypted information is exchanged freely and even broadcasted wirelessly and networked machines are accessible via insecure file transfer protocol (FTP).What happens in case of malfunctions of such technical installations? Who is responsible? Who can be held liable in case of accidents? The first computer worm for automation systems (æSTUXNETÆ) (Symantec, 2010) was discovered during 2010.The paper is intended to create sensitivity among decision makers for potential security and resulting safety leaks and points out the current status quo in technical network security. It outlines best practices for secure networking and procedures for remote access and remote software updates on stationary equipment and mobile mining machinery. It describes how to ensure authentic and genuine configurations and software targets and how to ensure secure communication for autonomous and remote controlled equipment. For such equipment in particular, the following statement should apply: æThere is no safety without network securityÆ.

Sep 26, 2011

By H Zhang, M Karimi, M Hassan, S Saydam, B Li

With the prevalence of Mine Internet of Things (MIoT), different types of sensors have been widely deployed in mine sites for environmental monitoring and operational management. Currently, sensors in mine sites are mainly powered by cables or batteries. However, the deployment and maintenance of a power supply network can be difficult and expensive, and batteries have a limited lifespan. The vibration energy harvesting (VEH) technology can be used to provide power for lowpower sensors in mine sites. This presentation briefly introduces three widely used VEH methods (ie piezoelectric, electromagnetic, and electrostatic). The performance of a commercial electromagnetic energy harvester (ReVibe model D) is evaluated based on the vibration of a lab vibrator (3 g, 50 Hz) and an idling SUV automobile (0.3 g, 25 Hz). Experimental results indicate that a ReVibe energy harvester can generate adequate electricity to power a sensor, and its power output depends on the load resistance as well as the vibration frequency and amplitude of vibration sources. To apply VEH to mining applications, this study also analyses the characteristics of vibration sources at the mine site based on the vibration data collected from various operating machines in a coal handling and preparation plant (CHPP). The vibration analysis results indicate that all the measured vibration sources in the CHPP can generate stable and abundant vibrations, characterised by substantial amplitudes (up to 5.55 g) and low dominant frequencies (ranging from 14 Hz to 25 Hz), which are sufficient for VEH.

Sep 1, 2024

By Aiming Z, Shenyi S, Xialei W

Zhangmatun Iron Mine is situated in the suburbs of Jinan city. Shandong, China. Because of surface environmental constraints, no suitable site can he selected to dispose of mill waste. The full mill tailings must be disposed of underground. This paper deals with the work conducted at Zhangmatun mine to develop a total tailings backfill system, taking advantage of a double- shaft blade mixer and an activating agitator to prepare backfill. Cement and ground slag are added to tailings for strength development. Two scopes have been filled and the pillars have been effectively mined out during the field trial. The application of innovative total tailings backfill technology is a new concept at the mine. Detailed planning has achieved a close integration of mining, milling and backfilling. Full mill tailings, with or without rock, are disposed of underground in a continuous process to fill, totally and systematically, the cavities formed by mining.

Jan 1, 1998

By R Wei, Y Peng

With the depletion of high-quality ores, the efficiency of extracting difficult gold ores through flotation and leaching becomes very important in the mining industry. Iron contaminants, sulfide and carbonaceous coatings on the surface of gold and gold bearing minerals significantly hinder the recovery of gold during gold processing. As the surface of gold minerals is easily contaminated, coatings of iron oxides and iron hydroxides originated from the grinding process and oxidation of iron sulfides will cause a retarding effect on both gold flotation and leaching.To mitigate the processing issues caused by undesirable surface coatings on gold minerals, a new technology in treating surface coatings of iron contaminants has been developed. The pulp potential and pH of the slurry are altered to allow dissolution of surface coatings which are further excluded by the use of complexing reagents. The current work shows that iron contaminants can be removed from the surfaces of gold through Eh-pH adjustment and chelation which result in significantly improved gold flotation response. The addition of complexants aids the formation of iron chelates to prevent the iron species in the solution from forming iron oxide and iron hydroxide in the flotation conditions.CITATION:Wei, R and Peng, Y, 2014. Mitigating the effect of surface coatings on gold processing, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 187–192 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By Revy T

A testwork program aimed to improve the assaying of underground face samples established that for an Accelerated Cyanidation Extraction using the LeachWELLTM 60X catalyst, followed by an Aqua Regia finish (to quantify non-cyanide-extractable gold): ò Assay results (including the aqua regia finish) from a full set of samples from one underground face can be returned within four hours. ò The reagent dose to make the method simple and 'bullet-proof' is 8 gm LeachWELLTM 60X and 20 gm NaCN per 200 gm sample (30 per cent solids). Pulverising is to 90 per cent passing 75 micron (compared to the standard of 90 per cent passing 150 micron), and cyanidation is completed within one hour - however both might be further optimised. ò The LeachWELLTM/Aqua Regia results demonstrate that Fire Assays suffer from a significant nugget effect which makes the Fire Assay data relatively unreliable. ò Original costs, specific to Bannockburn (viz including an Aqua Regia finish), handling approximately 20 000 to 25 000 per annum is estimated to be $5.40, ie about one-third less than fire assaying. Optimising is further reducing these costs. It is estimated that the LeachWELLT"'/Aqua Regia assay procedure has reduced the probable error limits of any given assay of this ore from the range 0.74x to 1.36x for Fire Assay, to an appreciably smaller range of 0.90x to 1.11x. Thus for a cut-off grade of 1.60 g Au/t, samples with Fire Assays ranging up to 2.18 g Au/t have 25 per cent chance of being below cut-off, while samples with Fire Assays as low as 1.18 g Au/t have an equal chance of actually exceeding cut-off grade. This 1 g Au/t range in uncertainty is generally unacceptable for many practicalgrade/tonnage relationships. By contrast, using LeachWELLTM + Aqua Regia assays, the estimated corresponding limits are 1.44 g Au/t and 1.78 g Auk respectively - a far more tolerable 0.34 g Au/t range of uncertainty. Subsequent data has demonstrated that sufficient accuracy for grade control is achieved by Accelerated Cyanidation alone, further halving the cost of assays.

Jan 1, 1994

By A C. Edwards

The Mesozoides of North-Eastern Asia represent a collage of exotic terranes which were accreted to the margins of the Siberian continent. In the Late Precambrian and Phanerozoic, the passive margin of the Siberian continent (the current north-east) broke up into a number of discrete fragments as a result of rifting events in the Riphean, Early and Middle Paleozoic. Rift related mineralisation includes stratiform and stratabound copper and base metal mineralisation in the structures of the Omulevka, Okhotsk and Prikolyma basement terranes, as well as along the edge of the Siberian continent in the Paleozoic sediments of the Verkhoyansk passive margin. During the Late Mesozoic the terranes were reassembled in a series of accretionary events. At the end of the Jurassic, the velocity of the Kula plate increased, and the opening of the Canadian Basin in the Arctic commenced, changing the vectors along which the Siberian and North American plates moved. Island arcs terranes were pushed back onto the Omolon super-terrane which was in turn pushed onto the Siberian Craton in a series of massive collisional events that resulted in the restructuring of the whole region. Numerous granitoids characterised by collisional and island arc chemistries with Au and accompanying Sn, and W mineralisation were emplaced. Mesothermal gold-quartz mineralisation was emplaced in a series of narrow belts that adjoin major crustal sutures and that spatially overlap belts of granitoids and zones of subgreenschist metamorphism. Each of these gold-quartz vein belts corresponds with a specific collisional phase. In the middle Cretaceous, the Okhotsk-Chukotka volcanic belt developed along the paleo-Pacific margin of the Siberian continent. Epithermal Au-Ag developed in the volcanics and shallow mesothermal Au-Ag-quartz and Au-Sb mineralisation developed in the Mesozoides. Porphyry and skarn style mineralisation developed in both the island arcs and in the continental Okhotsk-Chukotka Volcanic Belt.

Jan 1, 1999

By A McGann, P J. Coghill, D Miljak

"It is widely accepted that bulk ore sorting could provide a step change in processing of low-grade ores. For this to be achieved a rapid, accurate bulk sensor of grade is required as well as sufficient natural variation of grade in the ore stream. CSIRO trialled a magnetic resonance (MR) sensor capable of measuring chalcopyrite, and by inference total copper grade, on the 1300 t/h Ridgeway portal conveyor. The gauge produced an unprecedented set of data down to a 1 t scale for months at a time. This paper analyses the measured variation and compares it to a simple model derived from the bore core data and mixing within the block cave mine.The model of the small-scale (<1000 t) variation is developed using fractal methods which have successfully been used in the past for copper porphyry deposits showing a power law or near power law distribution of copper grade and vein sizes. These fractal distributions have two features highly favourable for segregating ore, a large proportion of low-grade pods and the large-scale spatial clustering of grade. We show the presence of fractal ordering in bore core data at short range in the Cadia Ridgeway porphyry deposit and measure its persistence in the crushed rock produced by the Ridgeway block cave mine over one month. The model is then extended to demonstrate the effect of varying head grade, mixing and pod (or diversion) weight on bulk sorting efficiency.CITATION:Coghill, P J, Miljak, D, McGann, A, 2016. Modelling Grade Variation in Crushed Ore at Cadia Ridgeway and Its Potential Consequences for Bulk Ore Sorting, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 77–88 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By C Sellens, L D. Fabbro, S Vink

The Fitzroy River Aqua-Eco Health Project is a collaborative research project between the Central Queensland University, the University of Queensland and BMA. It is designed to assess the aquatic ecology and health of the streams within the Fitzroy catchment located adjacent to mine sites. The universities are conducting an independent sampling program expected to yield the most comprehensive monitoring to date. The project design incorporates in situ testing of water quality variables including temperature, dissolved oxygen, conductivity, oxidation reduction potential, pH and turbidity. Water and sediment chemistry incorporate testing for sulfate, suspended solids, nutrients and metals. This sampling is complemented by quantifying changes in the abundance and diversity of a wide range of biota, including microbial, macro invertebrates and fish.This paper will detail the program and highlight some of the particular difficulties in conducting this type of research in ephemeral stream systems. Case study examples will be used to illustrate insights being gained from the program. CITATION:Fabbro, L D, Vink, S and Sellens, C, 2013. The Fitzroy Aqua-Eco Health Project, in Proceedings Water in Mining 2013, pp 117-120 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By P J. Bangerter, J Pan

Optimising for Net Present Value (NPV) with a strategic optimiser such as COMET, Prober-E, Blaser or Minemax has hitherto lacked a dynamic method for analysing the so-called third-order outcomes (such as Carbon emissions) of optimisation within life-of-mine planning. Optimisation, per se, has natural effects on carbon emissions in a life-of-mine plan. Contemporary strategic planning employs a mathematical optimiser to make sense of non-linear data (ie a block model) and produces a best-NPV optimised mining schedule, within a set of constraints. The very act of optimisation influences emissions, and in a dynamic way.

Aug 2, 2023

By E Ruhanen, S Kauvosaari, M Kosonen, C Meintjes

The Yara Siilinjärvi plant is located in the central part of Finland. Siilinjärvi is Western Europe's only apatite mine and annually it produces 1 Mt of apatite concentrate, which creates approximately 10 Mt of tailings.At the beginning of 2017, tailings handling in Yara Siilinjärvi was brought to a new era, by replacing the conventional tailings storage facility with a new tailings treatment plant. The new high-density tailings disposal system with two paste thickeners increased the percentage of solids in the slurry from 45–48 per cent to 66-68 per cent, making it possible to deposit as a paste. This extended the life-span of the current tailings storage facility by 15 years; from 2020 to 2035.This paper presents the storyline of the Yara Paste Plant Project. The project began with laboratory testing and then progressed to pilot-scale thickening and beaching trials. After some successful pilot trials, the final process design was implemented. Process instrumentation and automation played a key role in the project, as the aim of the Yara Project was to make the plant operable remotely from the main plant. An advanced control system is needed to maintain process stability and the desired operation point in various operational circumstances.This paper discusses the results from the Yara site since the new tailings treatment plant commenced. Some of the main points are that the operation has been running consistently with an underflow solids content of 66-68 per cent, with average beach slope angles of 3.5 degrees in the tailings disposal area. This control system additionally facilitates minimum use of flocculant, which delivers significant savings to operating costs. Robust thickener operation also leads to the trouble-free high-density pumping and high availability of the Paste Plant. During the first year of operation, the plant’s availability has been very good, over 97 per cent.Currently, the plant still has its own staff working there during the daytime, but the Paste Plant is now already operated remotely during the night shifts. The long-term goal is to gradually transition into operating the plant completely remotely.CITATION:Ruhanen, E, Kosonen, M, Kauvosaari, S and Meintjes, C, 2018. Optimising the operation of paste thickening at the Yara Siilinjärvi Plant, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 297–310 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By Anievas JB, Sevillano AC

This paper describes the acquisition, exploration, development, initial operation and subsequent financing of the Bulawan mine by means of a listing on the Toronto Stock Exchange of a subsidiary of the parent company, Philex Mining Corporation.Located on the island of Negros in the Philippines the property is unique on at least two counts: it is a disseminated gold deposit that occurs in a region of predominantly porphyry copper mineralisation; and it is a gold deposit that is mined by a bulk method of extraction (front and block cave) instead of the normal selective mining methods.

Jan 1, 1997

By I Cameron

Simulation is increasingly being used to analyse mineral processing operations and explore efficiency options. Engineers that use simulation are rightly concerned with the quality and applicability of the underlying models. However, many of these models have a significant empirical component, and the best structure for this component may not be apparent. There is an opportunity to improve the quality and application range of these models by exploring potential structures for this empirical element. One approach to this problem is the use of structural optimisation, which is a formalisation of the model development process. This method searches through a family or hyper-structure of candidate models for a model that is optimal with respect to some measure of model quality. This method has been applied to the modelling of an industrial flotation circuit. The result was a model that was a significant improvement over a number of standard models reported in the literature. Structural optimisation provides a method to compare potential models in a systematic and efficient way, and hence to improve the structure of process models.

Jan 1, 1998

By Fawcett M

Pine Creek Goldfields Limited (PCG) is rehabilitating the Enterprise Pit to an aquatic habitat and potential water resource. This paper discusses the development and implementation of that plan. Pine Creek Goldfields Ltd's Enterprise Mine is located approximately 230 km south of Darwin. Open cut mining of the orebody commenced in 1985 and continued for eight years with 14 million m3 of ore and overburden extracted. Geochemical testing of exposed rock types in the pit has demonstrated a propensity to produce acid, and dissolved metals. A plan of management has been developed and implemented to minimise the risk of acid formation and improve the overall water quality in the final void. In developing the plan prime consideration was given to reducing the potential for pit water to impact upon the regional groundwater. An interception system was constructed on Pine Creek to divert approximately 9 km2 of upper catchment into the northern end of the Pit. Construction of the diversion system was completed in December 1993 and a comprehensive surface and groundwater monitoring program initiated. The monitoring program and associated studies are also discussed.

Jan 1, 1994

By R A. Pax

Electrostatic separation is a core requirement for the beneficiation of mineral sands suites to provide valuable product. Although the basis of electrostatic separation has been understood for some time, the details required to be able to calculate the metallurgical performance of a separator has not previously been achieved from a mechanistic perspective. Empirical models have had some success but require extensive test work. Traditionally, performance of an electrostatic separator is determined by careful experimental work using the target mineral suite. Although electrostatic separation was invented at the end of the 19th century, very little modification of the basic equipment occurred until relatively recently, with the addition of a plate electrode to aid separation. Previously, the author has presented results, calculated using finite element modelling (FEM), of the electric fields present in an electrostatic separator in various configurations. This paper will present some new mathematical modelling work, which uses the FEM determined electric field configurations but also incorporates some fundamental physical processes that provide insight as to the limitations and opportunities for this important separation technique.

Oct 5, 2011

The Kaltails Project is situated close to the city of Kalgoorlie-Boulder in Western Australia. Located on the south-eastern fringe of the Golden Mile, Kaltails has been in operation since June 1989. The tailings forming the reserve for Kaltails have been derived from 100 years of underground mining on the Golden Mile, but, some of the re.;erve has been retreated in the past. A map of the tailings reserves and treatment plant site is presented as Figure 1. The gold project is a joint venture between Poseidon 90 per cent and Gold Corporation (ten per cent) and is managed by Poseidon Gold Kaltails.

Jan 1, 1992