Search Documents

By Sandvik

Fine grinding in an air-swept ball mill working in closed circuit with a forced vortex air classifier has been investigated first in continuous laboratory and then in industrial scale. Results from the laboratory circuit have shown significant influence of mill load (powder filling) on the capacity of the circuit. In laboratory scale the mill load was measured and controlled by a weighing platform placed under the complete mill set-up. The mill load of the industrial air-swept ball mill has till now been controlled by measuring the power consumption of the mill motor. Thus, it was necessary to operate far from the range of optimal mill filling. To improve the circuit performance, alternative ways of mill load measurement were investigated. An important factor was investment cost, as many fine grinding mills operate in relatively small circuits that do not wan-ant large investment. In this case the task was accomplished by using a piezoelectric strain transducer, which detected strain changes in the mill shell. It was installed in the midpoint of the shell, where the highest deformation was obtained. As the transducer was on the top position, it indicated compression, and on the bottom position it measured tension. By taking the difference between the readings, it was possible to calculate total strain variations, directly proportional to the mill load. The signal from the transducer was sent to a control room via a cordless infrared communication system, employing a microprocessor control card, which could further regulate other operating parameters of the circuit according to the software model. The installation required very low investment cost and provided simplicity of application as well as stability and reliability of characteristics under severe industrial condition. The measurement system made it possible to optimise the mill load and thus increase the production from 3.2 to 3.7 dh (15 per cent), and stabilise the circuit operation.

Jan 1, 1995

Quite often the reserve assessor becomes enamored with the numbers gen- erated and forgets the basis for his assessment. The quality of the assess- ment can only be as good as the quality of the input data. The use of seismic data from the Gippsland Basin in assess- ing Esso/BHP's oil and gas reserves is an excellent example of this principle. By significantly improving the quality of seismic data, a much more reliable estimate of a field's reserve potential can be made. In addition, it provides the basis for further delineation drill- ing which, as recent experience in Gippsland has shown, often leads to increased reserves.

Jan 1, 1979

A series of numerical experiments were performed in order to define the fracture strength of schistose rock during crushing. Fracture strength was shown to decrease as the fabric aligned with the principal axis of loading. One of three types of characteristic stress-strain behaviour are defined by the orientation of the fabric with respect to the applied stress.

Jan 1, 1993

By Hanaoka K, Ikeda K

Kakogawa Works, Kobe Steel, Ltd. has two pelletizing plants and one sintering plant, and the blast furnaces have been operated with 30 - 50% pellets. At Kakogawa Works, various improvements in pellet quality have been carried out since the beginning of operation of the pelletizing plant. Especially, dolomite-fluxed pellets developed in 1975, have superior high temperature properties. The fuel rate of the large blast furnaces at Kakogawa Works has been reduced to 450 kg/t- hn by using a high percentage of dolomite-flux ed pellets.

Jan 1, 1980

In the last 40 years nuclear energy has taken its place as a major source of electricity worldwide. It now produces 17 per cent of the world's electricity and could conceivably produce a higher proportion, to displace some six billion tonnes of carbon dioxide emissions per year. Concerns about global warming and environmental quality now underline the virtues of nuclear electricity among alternative sources of energy. Global electricity demand is rapidly increasing as a proportion of total energy usage. The proportion has doubled since 1960 and the demand is expected to increase at least 75 per cent between now and 2020. The source of this extra capacity, and the replacement of present capacity, raise questions with major resource and environmental implications. Today nuclear energy is a mature technology. Over 1200 nuclear reactors have been built and operated, some of these have been decommissioned, and among the 440 reactors in commercial operation the first advanced reactors are now entering service. Some 8000 reactor-years of operation have, with the sole exception of Chernobyl, shown nuclear energy to be extremely safe and reliable. High-level wastes are being managed properly and in different parts of the world two strategies are applied to this. Australia has a major role as a long-term supplier of uranium, since it holds almost 30 per cent of the world's reserves. This, along with an impending sellers' market for uranium, is making it an opportune time to develop new mines here. However, after several decades of concern about civil nuclear energy contributing to the arms race, we now have uranium liberated from nuclear weapons stockpiles being diluted for use in civil reactors, which will supplement ex-mine supply. The public acceptability of nuclear energy remains the critical factor in its future and hence in ours.

Jan 1, 1997

By R R. Anand

Recent research by CRC LEME from an Australian mineral exploration perspective, has focussed on regolith architecture and mechanisms of geochemical anomaly formation, within transported regolith. Methods have been developed for the rapid production of regolith-landform maps which is the starting point for understanding regolith architecture in the third dimension. Methods for development of 3D regolith models are less well advanced, and require integration of all available geological and geophysical datasets, but still with a heavy reliance on drill-hole information. The base of the transported regolith û the unconformity û remains the most important regolith boundary for geochemical sampling in transported regolith terrains. A new generation portable spectral logger, employing a broader spectrum can interpret important features from drill chips within the regolith. This allows internal architecture, redox fronts and the all-important interface to be objectively identified. Transported lateritic components can provide vectors to mineralisation in depositional regimes. Palaeomagnetic and new radiometric methods which date individual phases of the regolith provide evidence of different episodes, each characterised by different geochemical dispersion patterns in transported regolith. Along with lateritic residuum, calcrete is prime sampling medium. Calcrete is probably enriched in gold through physical and biological processes, rather than straight chemical processes. In South Australia, the lowermost calcrete layer buried within the depositional regime, especially where it lies directly over the silcrete layer at the buried interface, is the desired sampling medium. Certain gum trees, with deep roots in transported regolith have been shown to record anomalous values of gold and basemetals in leaves, twigs and bark. Anomalous metals in acid-sulfate soil seeps can also provide a window through sedimentary cover in respect of mineralisation in the basement. A number of Yilgarn occurrences of gold anomalies in transported cover, strongly infer hydromorphic and biological mobilisation of gold. This inference is supported by micro-analyses of regolith mineral hosts in hardpans and mottled sediments, which show gold and pathfinder elements prefer to reside in goethite and specific types of clay minerals. This creates anomalies in specific mineral phases. However the inference that that these are sites of mobile or labile metal ions remains enigmatic. Similarly there is inconclusive evidence that selective extractions will provide an anomaly not otherwise detected by conventional total dissolution methods. Hydrogeochemistry is a promising exploration tool for basemetal exploration. The importance of microbes in both the dissolution and precipitation of gold in the Australian regolith is demonstrated. We are on the verge of identifying the functional gene sequence of individual active microbes. A consideration of possible mechanisms for creating anomalies in soils above transported regolith, presents difficulties in facilitating upward movement of ions from the watertable to the surface. Perhaps the best avenues of research lies with surrogate soil gases, and biotic transfers.

Jan 1, 2004

The transition from low stress to high stress conditions is a challenge eventually faced by most mines in Australia that extend to depths greater than (generally) about 1000 m. In areas with strongly adverse 'stress versus depth' gradients, such as some parts of Western Australia, significant stress-related problems have occurred at depths as shallow as 300 m below surface. The actual depth at which the 'transition' occurs is a function of the local pre-mining stress field, the strengths of the various rock types hosting the deposit and the layout and sequencing adopted in the mine. Stress-related damage can result in increased support costs, and delays associated with rehabilitation and disruption to production. In the worst case, where strong seismicity and associated damage occurs in active mining areas, 'exclusion' zones and 're-entry' protocols may be required. These can severely disrupt production. A key aspect of managing the transition is the recognition of the onset of stress-related ground behaviour. Damage mapping can be used to develop understanding of the relationships between mining activities and the local and regional response to them. Carefully documented case histories provide a basis for calibrating numerical models. This paper discusses some of the typical styles of ground behaviour observed in higher stress conditions in underground mines. A simple damage classification scheme is described to assist in 'damage mapping' of mine tunnels. An example of damage mapping is presented to illustrate an approach commonly used for recording stress-related damage.

Nov 25, 2010

Mount Isa Mines' Hilton Mine was brought into large-scale production in 1990/91 at a time of sharply falling metal prices. To ensure the operation's survival and eventual prosperity there was an urgent need to reduce operating costs and increase revenue. A target of a 40 per cent increase in productivity over five years was set. Strategies to obtain the required improvements were developed on the basis of greater involvement and increased contribution from the workforce, major changes to the mining methods and the development and application of new technology. This paper describes the organisational, operational and technological changes that have been implemented at Hilton and presents the results achieved to-date.

Jan 1, 1993

By Roddick F

From its mining lease at the northern end of Cohens Reef at Walhalla in the North Gipps- land mountains, the Long Tunnel Extended Gold Mining Company produced 13,695kg of gold, which at 1982 prices represents a value of about $140 million. In the period 1885 to 1908 the mine was one of Australia's principal reef gold producers, being top Victorian producer in six of these twenty-four years. Prior and subse- quent occupants of the lease produced an addit- ional 160kg of gold. The Extended and the other mines on Cohens Reef whilst contributing importantly to the financial resource of Victoria, were the sole important support for the substantial town of Walhalla that had grown up around them. When the mines closed, Walhalla gradually reduced from a bustling developed town to the present attractive mountain village so favoured by tourists.

Jan 1, 1982

By Knasmillner

During blasting body wave interaction with geometrical surfaces induces Rayleigh-waves which propagate along free surfaces, e.g. crack faces or delaminated rock layers. These Rayleigh-waves carry most of their energy within a very shallow surface layer and propagate with very little attenuation in real rock materials. Upon interaction with a crack front a very strong mixed mode stress intensity factor may result and lead to fracture initiation. On the basis of experimental photomechanical results the history of dynamic stress intensity factors Kt and K2 will be studied in Detail.

Jan 1, 1990

By Patridge A. C

Observations of coal stockpiles subject to unusual levels of instability showed that the particular coals exhibited 'gap grading', a relative lack of intermediate size particles. This led to a suggestion that fine coal particles within the pile might have been induced to migrate under the influence of water flow and to concentrate in relatively impervious layers, resulting in local water saturation and reduction of shear strength. To investigate this suggestion, a large test column has been constructed and washed coals with various levels of fines content have been subjected to a downward flow of water. Subsequent examination of the bed of coal within the column confirmed the percolation of fines and their concentration into horizontal layers, and showed the development of zones of saturation above those layers. Shear box tests showed differences in cohesion and internal friction angle between coals with different percentages of fines, supporting the hypothesis that fines percolation may lead to decreased stability.

Jan 1, 1995

Aitik, a Boliden owned and operated open pit mine located in northern Sweden, will expand production from 18 Mt per year today to 36 Mt per year copper ore during 2010. The challenge for the mine operation is to double production with a planned increase of the shovel and truck fleet of only 50 per cent. This will be achieved through improved shovel and truck utilisation and productivity. In early 2005 Aitik started projects to enhance the utilisation of truck engine hours and to reduce fuel consumption. Both projects were successful, within a year efficient2 utilisation of engine hours increased from 60 per cent to 75 per cent and fuel consumption was reduced by six to eight per cent. The truck utilisation project focused on minimising idle truck hours by for example four operators on three trucks thus reducing idle engine hours to minimise lost time for breaks and shift changes. Other measures included focusing on improved dispatch usage, parking trucks when overtrucked, etc. Eco-driving was a project together with Swedish Road Administration with the objective to combine economical and environmental savings. To keep the focus on eco-driving a reward was set up for the shift team with the lowest fuel rate over rolling 15 weeks periods. Both activities included a comprehensive training program for mine foremen, dispatchers and truck operators focusing on efficient use of trucks from economic driving to optimised truck dispatching and minimising idle engine hours. Online monitoring of trucks activities and fuel consumption combined with continuous reporting gave shift foremen and management a tool to discuss and follow trends and individual shift team performance. The combination of close monitoring of mainly organisational practices and operator training resulted in significant productivity increase and lower operating costs without any capital investments.

Jan 1, 2007

The results of about 30 years of exploration and mining activities and research studies in the Kambalda mining district, Western Australia, have led to general agreement that the komatiite-associated Ni sulphide ores formed as a result of igneous processes (Ross, 1974; Ross and Hopkins, 1975; Gresham and Loftus-Hills, 1981; Cowden, 1988; Lesher, 1989 and many others). Despite this agreement, the controls on sulphide supersaturation and concentration of the resulting sulphide in a limited zone, remain uncertain and controversial. A major uncertainty is the source of sulphur in the ore deposits. Two principal sulphur sources have been proposed: 1. komatiite lava/magma (Hudson, 1972; Naldrett, 1973; Lesher et al, 1981; Cowden, 1988; Foster et at, 1995), and 2. sedimentary material (Groves, Barrett and McQueen, 1979; Lesher, Arndt and Groves, 1984; Lesher, 1989; Lesher and Campbell, 1993). Resolution of the uncertainty regarding the sulphur source is required for a complete understanding of the controls on ore formation, which in turn would significantly impact exploration strategies in the Kambalda mining district and elsewhere. This paper reviews the constraints on sulphur sources for the komatiite-associated Ni sulphide ores in the Kambalda mining district. The focus is on the general characteristics of the ores and surrounding rocks: individual ore deposits are not described, though specific examples are noted where appropriate. The stratigraphic and volcanic settings and geochemical (major and trace element and isotopic compositions) characteristics of the ore deposits and surrounding rocks are considered within the context of the competing sulphur source models, and future directions of research in the district are noted.

Jan 1, 1996

By M Barker, H Li

The total number of tailings accidents has reduced from over 50/decade in the 1960s-1980s to less than 30/decade in the 2000s to 2010s. However, the rate of significant tailings dam failures has not been reduced. The significant tailings dam failures the mining industry experienced in the recent history include: Merriespruit, South Africa, 1994; Los Frails, Spain, 1998; Kolontár, Hungry, 2010; Mount Polley, Canada, 2014; and Samarco, Brazil, 2015. The conventional Factor of Safety approach itself may not be enough to further reduce the rate of significant tailings failures due to its limitations such as uncertainty. For example, the same factor of safety could have a vast range of annual probability of failure for different tailings dams, and insufficient consideration of failure consequence. This paper presents a risk based approach for design with the objective being to minimise tailings dam failures, especially those significant tailings failures with high consequence and low probability. This approach includes risk based design and risk management using bowtie tools. In the risk based design, quantitative analysis will be used to estimate the annual probability of failure and the tolerable failure criteria is linked to the consequence category. Bowtie analyses will be used to understand hazards and risks and identify and select independent controls that are effective in preventing and mitigating catastrophic failures. In this paper, examples of risk based design and bowtie analyses are presented and discussed. CITATION:Li, H and Barker, M, 2018. Risk-based approach for minimising tailings dam failures, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 397–414 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

The use of teleoperation in mining is increasing due to requirements to improve safety and reduce the number of people required to work in remote and difficult environments. We recently completed a project to develop a teleoperated control system for a rock breaker at an iron ore mine in the Pilbara region of Western Australia, with the objective of demonstrating the feasibility of remote rock breaking over long distances. This required controlling both the rock breaker and an array of pan-tilt-zoom (PTZ) cameras using joysticks. Controlling the cameras distracted operators from the primary task of controlling the rock breaker to position and fire the hammer. This lengthened task times as both the operator's attention and their hands have to swap between different control interfaces. In this paper, we present a novel design using human eye gaze as an interactive input for the remote camera control. It follows a simple and natural design principle: Whatever you look at the screen, it goes to the centre. A prototype system has been implemented by integrating computer vision based eye tracking technology, with the advantage of being real-time, robust and marker-less. We conducted a user evaluation, where users undertook a control task while obscuring the direct view of the working area and using a remote camera to transfer the live video stream as the visual feedback. Subjects were required to participate in the experiment using eye tracking camera control and traditional joystick control respectively. The statistical analysis of objective measures indicated that our novel eye tracking control significantly outperformed the joystick control. The results of the post-experimental subjective measures also revealed much higher user preference for using eye tracking control, which provides clear evidence that this design is a better interface for remote camera control in mining teleoperation settings.

May 1, 2010

By Spencer P. A

Bacterial oxidation, previously known as bacterial leaching or bio-leaching, has been applied at laboratory and pilot plant scale to many refractory ores and concentrates around the world. The most common bacterial culture used in this process has been Thiobacillus sp. This organism is limited in commercial application, especially in Australia for several reasons. The optimum operating temperature range for this culture is 30¦C to 40¦C and high levels of some metals such as arsenic, silver, and copper have toxic effects on the culture thus reducing its effectiveness. The culture employed by BacTech (Australia) Pty lid is a moderately thermophilic culture which operates in a temperature range of 40¦C to 55¦C (which is more amenable to the Australian climate) and with higher resistance levels to metals often found to be toxic to Thiobacillus sp..

Jan 1, 1991

By Neill A. O, Worth I, O&apos

The formation of Kalgoorlie Consolidated Gold \lincs 1't% Ltd hati pla,xd all the major the gold producing areas adjacent to the city of Kalgoorlie/Boulder under one management, enabling the development of the 'Super Pit'. This has facilitated the economic optimisation of the resource. Optimisation has been achieved by the timely collection and presentation of data and the use of these data to reduce costs and improve planning procedures.In particular the following issues have been addressed:ò the reduction of the impact of the mining activity on the adjacent urban population centre,ò implementation of safety procedures for mining through underground voids,ò the determination of the optimum bench height and mining method for ore production benches and blast design. This system is fundamentally based on maintaining a high degree of selectivity while achieving a balance of relatively low unit operating costs,ò assessment of the comparable benefits of contractor versus owner operated earth moving equipment, andò the development of effective ore body models, production reconciliation and the long term mine planning procedures to facilitate effective strategic planning.

Jan 1, 1993

By M A. Llano-Serna, D J. Williams, L Bu

Tailings dam failures continue to occur worldwide at an unacceptable rate, averaging two events annually over the last 100 years. Furthermore, tailings dams continue to grow in size, increasing the potential release of tailings and water should they fail. Tailings are generally deposited in a slurry state, with the potential to flow if containment is lost. Understanding the generation and propagation of excess pore water pressure on failure is critical to predicting the flow and run-out of tailings. This paper presents numerical modelling using the material point method indicating that tailings run-out processes may be self-enhanced by the excess pore water pressure induced during the collapse of the containment. Moreover, it is shown that geomorphological features, such as the slope and its surface roughness downstream of the tailings dam, influence the pore water pressure dynamics upstream of the advancing toe.CITATION:Llano-Serna, M A, Bu, L and Williams, D J, 2018. Excess pore water pressure induced during tailings run-out, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 377–383 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By Blair J. R, Barrett J. R

In many underground mining applications where-dry fill is used, only a token acknowl- edgement of the fill properties is given. It is the aim of this paper to induce mining engineers to consider dry fill as an engineer- ing material rather than a mass to place in unwanted voids. Dry fill is generally cheap, inert and readily available, but it can still contribute to mining performance. In particular, the choice of the dry fill becomes more critical as stope sizes increase, controlled choked draws are used or pillar recovery introduced. Selection must be initiated from an evaluation of the role of the fill in the mining operation. In most cases the fill must be chosen before quarrying begins and an investigation must be made of available sources and appropriate quarrying methods. Some of the properties of fill are described together with evaluation techniques. A com- parison of placement conditions is limited by the complexities of material flow and degrada- tion: However, field and model tests can aid interpretation in these cases. Examples are given of aspects of dry fill selection and their incorporation in mining design.

Jan 1, 1973

Ore deposit modelling is becoming an increasingly accepted tool in mineral exploration. Successful models have already been proposed for several ore deposits of base metals and gold, but tin has so far received comparatively little attention, perhaps because of an excessive preoccupatioi with alluvial operations. This situation is rapidly changing and some of the world's most profitable and newly commissioned tin mines are large, primary tin deposits. Some basic principles of ore deposit modelling are briefly reviewed and the fallacy of an excessive reliance on grade tonnage diagrams based on the tin industry worldwide is discussed. The four proposed models and submodels of large, hard-rock, tin deposits focus on basic concepts such as the spatial relationship with "tin granites", depth of emplacement and the level of erosion. General concepts are drawn. The modelling of large primary tin deposits is reviewed not only in its geological and exploration aspects but also in its mining and economic implications.

Jan 1, 1986