Search Documents

By N. L. Carwile, G. W. Geil

A metallographic study was made of deformation twinning (Neumann lamellae) in ingot iron slowly deformed in tension at —196O and —150°C. The results showed that twinning is initiated mainly during the initial stages of plastic deformation. However, the breadth of the twins generally increases with increase in strain up to fracture of the specimen. HE results of an investigation of the effect of low I temperatures on the flow, fracture, strain hardening, and strain aging characteristics, and the true stress-strain relationship for specimens of ingot iron deformed in tension were reported recently.1,2 In that study specimens of ingot iron, in different initial conditions, were slowly deformed in tension at various temperatures between —196" and +100°C. A phenomenon observed, but only briefly reported, was the formation of deformation twins (Neumann lamellae) in the specimens deformed at the lower temperatures. Preliminary metallographic examination of these specimens indicated that there was apparently some correlation between the deformation twinning and the strain of the specimen and that this factor merited further investigation. Some recent investigations have indicated a direct association of Neumann lamellae and the fracture of the metal. Bruckner".' * postulated that the twinning immediately precedes the fracture and the latter is initiated by the stopping of the propagation of twins, either at subgrain boundaries or at other structural features. Tipper and Sullivan5 postulated that Neumann lamellae are initiated by the shock or a shock wave set up at fracture in the still highly stressed unbroken metal, and that a high rate of deformation is a necessary condition for their formation. An extensive metallographic examination, therefore, was made of many of the specimens used in the study of ingot iron at this Bureau and of additional specimens deformed to selected strains under various conditions. The present paper summarizes the effects of deformation under these conditions upon the breadth and scope of the deformation twins. Other features of twinning will be discussed in another paper. Material and Testing Procedure All of the specimens were prepared from one lot of ingot iron, as hot-rolled, of chemical composition other than iron as follows: C, 0.02 pct; Mn, 0.02; P, 0.005; S, 0.018; Si, 0.002; Cu, 0.10; 0, 0.058; and N, 0.002. Cylindrical tensile specimens with a 2 in. gage length were used. The reduced section was slightly tapered from each end; the diameter (0.438 in.) at the midsection of the gage length was about 0.003 in. less than at the ends. The specimens were finished to the final dimensions by grinding and polishing in the axial direction. The ends of the specimens were machined with 3/4 in. x 10 threads and the shoulder fillets were machined to a radius of 0.75 in. The specimens were extended slowly in tension (deformation rate less than 0.5 pct reduction in area per minute) while immersed in an appropriate cryogenic liquid maintained at the desired temperature. The minimum diameter of the specimen was measured during the test by means of a specially designed reduction of area gage accurate to 0.0001 in." A detailed description of the testing equipment and the method of maintaining the desired temperature is given in a previous paper.' Each specimen, after deformation to a specified strain at a selected temperature, was sectioned longitudinally and examined metallographically. The preparation of specimens for metallographic examination was carried out in the usual manner by mechanical polishing and etching. Results and Discussion Deformation twins in specimens of ingot iron extended slowly in tension at —196" and —150°C are shown by the representative micrographs of Figs. 1

Jan 1, 1954

By P. S. Kotval, H. Hahell

PRECIPITATION of M23C6 carbides at grain boundaries in austenitic steels and nickel base superalloys has received considerable attention. Hatwell and Berghezan,1 in a study using carbon extraction replicas, observed that dendritic growth of the M23C6 carbide phase occurred at grain boundaries in austenitic steels. Merrick and Nicholson2 have observed that in thin foils of "Nimonic 75" alloy the precipitation of M23C6 carbide was discontinuous at grain boundaries. Lewis and Hattersley3 have suggested that the type of M23C6 precipitation observed in Ni-Cr austenites represented the early stages of discontinuous precipitation. In a more recent study, Singhal and Martin4 have concluded that grain boundary M23C6 precipitation involves the migration of an austenite grain boundary by a mechanism very similar to that proposed by Tu and Turnbull.5 Tu and Turnbull's suggestion essentially involves grain boundary migration under the driving force arising from the difference between the surface free energies of the opposite sides of the plate. Thus, Singhal and Martin's observation4 implies that the first stage of discontinuous precipitation has taken place and that the grain boundary has provided a diffusion short circuit for the sub-stitutional solute atoms (principally chromium) which assist the preferential growth of the M23C6 plate in contact with the grain boundary. However, no evidence of the characteristic cellular morphology typical of discontinuous precipitation was found in Singhal and Martin's studies. Presumably, this is due to the low volume fraction (i.e., low supersaturation of solute) of the precipitating carbide reported by Singhal and Martin.4 Recently, Raymond6 has studied precipitation of the M23C6 carbide in Incoloy alloy 825 and shown that the growth of this phase is perpendicular to grain boundaries at 1400°F and in the plane of the grain boundary at 1700°F. The former aging condition resulting in discontinuous or "cellular" precipitation. Raymond has suggested an explanation for this behavior based on the relative rates of chromium diffusion by volume and grain boundary diffusion at the two different aging temperatures. In the course of a recent investigation on precipitation behavior in several ' strengthened superalloys, precipitation of M23C6 carbide at grain boundaries was studied. Under conditions of a high degree of supersaturation, the M23C6 carbide precipitates in the discontinuous or cellular morphology in Waspalloy (Ni-18.51 Cr-2.0 Fe-3.53 Mo-1.16 Al-2.78 Ti-0.09 C). This note presents electron microscopy observations of this mode of precipitation and its effect on mechanical properties. Specimens of Waspalloy after "solution" heat treatment at 1950°F show essentially single phase matrix with a few residual particles of "primary" MC carbide. In normal commercial heat treatments, precipitation of Ni3(Al,Ti) ordered fcc r' phase occurs throughout the matrix and M23C6 precipitates as globular particles at the grain boundaries. In these commercial heat treatments the degree of supersaturation during precipitation is low. However, if specimens of Waspalloy are quenched from the solution heat treatment temperature of 1950°F and then aged at an aging temperature where the degree of supersaturation is high, discontinuous precipitation of M23C6 occurs. Figs. 1 and 2 show thin foil micrographs of Waspalloy, solution heat treated at 1950°F, water quenched, and aged at 1292° and 1598°F, respectively, for 500 Fig. 1—Thin foil of Waspalloy, solution heat treated at 1950°F for 1 hr, water quenched, and aged for 500 hr at 1292°F. Magnification 15,500 times. Fig. 2—Thin foil of Waspalloy, solution heat treated at 1950°F for 1 hr, water quenched, and aged for 114 hr at 1598° F. Magnification 13,000 times.

Jan 1, 1970

By B. Haimson, C. Fairhurst

A criterion is Proposed for the initiation of vertical hydraulic fracturing taking into consideration the three stress fields around the wellbore. These fields arise from (1) nonhydrostatic regional stresses in earth, (2) the difference between the fluid pressure in the wellbore and the formation fluid pressure and (3) the radial fluid flow through porous rock from the wellbore into the formation due to this pressure difference. The wellbore fluid pressure required to initiate a fracture (assuming elastic rock and a smooth wellbore wall) is a function of the porous elastic constants of the rock, the two unequal horizontal principal regional stresses, the tensile strength of the rock and the formation fluid pressure. A constant injection rate will extend the fracture to a point where equilibrium is reached and then, to keep the fracture open, the pressure required is a function of the porous elastic constants of the rock, the component of the regional stress normal to the plane of the fracture, the formation fluid pressure and the dimensions of the crack. The same expression may also be used to estimate the vertical fracture width, provided all other variables are known. The derived equations for the initiation and extension pressures in vertical fracturing may be employed to solve for the two horizontal, regional, principal stresses in the rock. INTRODUCTION Well stimulation by hydraulic fracturing is a common practice today in the petroleum industry. However, this stimulation process is not a guaranteed success; hence, the deep interest shown by the petroleum companies in better understanding the mechanism that brings about rock fracturing, fracture extension and productivity increase. Geologists and mining people became interested in hydraulic fracturing from a different point of view: the method may possibly be employed to determine the magnitude and direction of the principal stresses of great depth. Numerous articles in past years have dealt with the theory of hydraulic fracturing, but they all seem to underestimate the effect of stresses around the wellbore due to penetration of some of the injected fluid into the porous formation.1-4 Excellent papers on stresses in porous materials due to fluid flow have been published5,6 but no real attempt has been made to show the effect of these stresses in the form of a more complete criterion for vertical hydraulic fracturing initiation and extension. This paper is such an attempt. ASSUMPTIONS It is assumed that rock in the oil-bearing formation is elastic, porous, isotropic and homogeneous. The formation is under a nonhydrostatic state of regional stress with one of the principal regional stresses acting parallel to the vertical axis of the wellbore. This assumption is justified in areas where rock formations do not dip at steep angles and where the surface of the earth is relatively flat. This vertical principal regional stress equals the pressure of the overlying rock, i.e., S33 = —pD, where S33 is the total vertical principal stress (positive for tension), p is average density of the overlying material and D is the depth of the point where S33 is calculated. The wellbore wall in the formation is considered to be smooth and circular in cross-section. The fluid flow through the porous elastic rock obeys Darcy's law. The whole medium is looked upon as an infinitely long cylinder with its axis along the axis of the wellbore. The radius of the cylinder is also very large. Over the range of depth at which the oil-bearing formation occurs, it will be assumed that any horizontal cross-section of the cylinder is subjected to the same stress distribution, and likewise that it will deform in the same manner. STATE OF STRESS PRIOR TO DRILLING OF WELLBORE At a depth D from the earth surface within the oil-bearing strata, it is assumed that the following are 1References given at end of paper.

By P. R. Sahm, T. V. Pruss, D. A. Gandolfo

Cb 3 Sn powders were hot-pressed to estahlish densi-fication conditions and assess the possible use of such compacts in multiphase structures with ceramic or magnetic inclusions. Superconducting transition temperatures, Tc, were measured as a function of powder particle size, pressing temperature, and second-phase admixtures. The highest transition temperatures were found in coarse powder (5 to 500 u) compacts and were only weakly depended on pressing temperatures up to 1200°C. Fine powders (below 5 p), however, both single-phase CbsSn and Cb3 Sn-composites, showed a stronger dependence on hot-pressing temperatures. While Al2 O3 phase admixtures did not affect T, much more, a Pronounced T, degradation was observed upon the addition of ferrimagnetic Fe2 Mno. 5 Zno.5 O4 powders. Likewise, critical current densities, Jc, at 4.2° K were lowered appreciably in the ferrite doped samples, whereas the neutral A1203 inclusiow gave slightly improved Jc values. MULTIPHASE structures in electronically active materials have recently gained in interest as pointed out by Galasso in a review article.' In superconductors the most widely reported group are eutectic alloys which have been mostly investigated with respect to the proximity effect.2"4 In addition, "artificial eu-tectics", for example in the form of mercury-vycor glass sponge5 or fine niobium wires imbedded in a copper matrix,= have been prepared to attain higher critical fields and critical current densities. The idea was to enhance flux pinning phenomena by second-phase inclusions or ho1es. 7 Flux pinning should also be possible by the introduction of insulator inclusions into a superconducting matrix. Ceramic-metal combinations are most easily produced by hot pressing (= pressure sintering), as it permits an almost unlimited selection of material combinations. Cb 3 Sn has been prepared by vapor phase growths or in the form of thin films. Large compacts must be sintered,1° however, and normally present difficulties. At temperatures below 1350°C insufficient densities are obtained and at higher temperatures the loss of tin due to dissociation upsets the stoichiometry. Hot pressing is a natural approach to circumvent the problems, since one can obtain satisfactory densities despite low sintering temperatures. This work was mostly concerned with establishing conditions to hot press Cb3 Sn and Cb3 Sn multiphase structures (= composites), because no data are presently available, and to evaluate these with respect to their transition temperatures. However, a few measurements on critical current densities were also carried out, in particular to assess the value of ferrimagnetic inclusions. I) EXPERIMENTAL PROCEDURE The experimental procedure involved the preparation of feed material and powders, hot pressing, and evaluation of the resulting ingots. As no attempts were made to synthesize Cb3Sn from the elements during hot pressing, feed material had to be produced. For this purpose, a stoichiometric Cb-Sn powder mixture was compacted into a 3-cm-diam ingot (80,000 psi) and then inserted into a quartz tube and evacuated. Rf heating was employed. Above the tin melting point (230°C) liquid tin was forced out of the ingot, but was pulled back by capillary action after approximately 0.5 hr of continuous pumping at 700°C. Thus, it appears that evacuation at this temperature caused desorption of impurity gas creating wetting surfaces which, later on, favored alloying at relatively low temperatures. After a presintering period of 17 hr at 800°C, the quartz tube was tipped off and sealed into another such larger-diameter tube which, in turn, was connected to a pump system. This configuration permitted a temperature treatment at 1400°C, carried out for 65 hr, without collapsing of the glass walls or unfavorable chemical interaction of Cb3Sn with the quartz. The resulting material was

Jan 1, 1969

By David Cornell

Back pressure test data on natural gas wells are short time test data of unsteady state nature. Performance curves from which unsteady state effects have been eliminated, called stabilized performance curves, are necessary for understanding the behavior of gas wells and for scheduling gas fields for periods up to 20 years. A calculation procedure has been developed whereby three day, seven day, 30 day, or other duration stabilized performance curves may be calculated from back pressure test data. Such curves are essential for correct gas deliverability calculations and gas field scheduling. I NTRODUCTION The manner in which a back pressure test is made will affect the slope of the back pressure curve because the radius of drainage changes with the length of time that the well is allowed to flow. The reciprocal of the slope of the back pressure curve is defined as n in Equation 1 and varies from 0.5 to 1.0. If the flow is viscous and the radius of drainage constant, n will have a value of 1.0. Because of turbulence in the formation near the wellbore, the pressure drop is usually greater than the viscous flow pressure drop and the exponent n is frequently less than 1.0. In addition, since the radius of drainage moves away from the well-bore during the test, the gas flows a greater and greater distance as the test proceeds, with a resulting increased pressure drop at the high flow rates, and, again, n for the test tends to be less than 1.O. The effect of the changes in the radius of drainage may be calculated and the results used in preparing stabilized performance curves for fixed values of the radius of drainage. Such curves can be made for a defi- nite time period, such as three day, seven day, or 30 day stabilized performance curves. These cukes will show the effect of turbulence near the wellbore and can be used to predict the performance of the gas well at any flow rate or for any production period. In order to discuss the importance of the radius of drainage quantitatively, it should be defined. Muskat" defines the radius of drainage as follows: "... the radius of drainage gives the distance from the well to which the approximately steady state condition has been established ... it being assumed that no gas is removed from any point until the radius of drainage has passed that uoint." An eauivalent definition of the radius of drainage is that radius at which the extrapolated portion of the steady state portion of the pressure gradient gives a pressure equal to the shut-in reservoir pressure. This definition is also implied in the back pressure equation. The radius of drainage is, then, the distance into the reservoir from which the gas appears to originate at any time. It is, however, only a useful concept and does not actually exist. Fig. 1 illustrates the definition of the radius of drainage. At the end of each flow period the radius of drainage may depend on three factors: (1) the duration of each flow period; (2) the rate of gas production; and (3) the rate and duration of the previous flow periods. In general, back pressure tests are conducted with various lengths of production time and at various flow rates. Each individual back pressure test, therefore, requires an individual analysis. The calculations of the change in the radius of drainage have been made, however, for the case of equal flow periods for all four production rates and several sets of increasing flow rates. Fig. 2 illustrates the results of such calculations made by the method of Cornell and Katz2 for the case of 8, = 50,000 and the flow rate increasing in the ratio 1.0:2.0:3.0:4.0 for each flow period. The increase in the radius of drainage during the test is apparent.

Jan 1, 1956

By E. I. Salkovitz, F. W. von Batchelder

DURING the last few years several papers1-' have been published in which internal friction measurements have been used to determine the quantity of carbon or nitrogen dissolved in a iron. This method is based on the fact that, in pure Fe-N and Fe-C alloys, nitrogen and carbon cause peaks in the internal friction vs. temperature curve; at a frequency of 1 cycle per sec (cps) these peaks appear at $-200 and +360C, respectively, and if internal friction is expressed as Q-1, which is equal to times the logarithmic decrement, this figure will, by coincidence, give the weight percentage of nitrogen or carbon in solid solution.' In most of the studies published, very pure iron (Puron) was used. In one case the influence of manganese on the behavior of nitrogen in a iron was mentioned.4 It would be of great value, especially for the study of aging and related phenomena, if this method could be applied to commercial mild steel with norrnal percentages of manganese, phosphorus, sulphur, etc. As a rule, in such steels carbon and nitrogen are present together, and the amounts of these elements in solid solution should preferably be determined separately. The fact that their internal friction peaks appear at different temperatures (+36° and + 20°C in pure iron) seems promising for such a selective determination. It is necessary, however, that the peaks are narrow enough not to interfere with one another, and further, that there is no effect from carbon on the behavior of nitrogen in stress induced diffusion, and vice versa. According to Fast,' however, in the presence of manganese the nitrogen peak gets wider and appears at a higher temperature nearer the carbon peak, and thus the prospects for selective determination are reduced. (The carbon peak was not affected by the presence of manganese.) But even if fully quantitative de- terminations of the two elements are not attained, some relative figures on the sum of them and an indication of which one is the predominant one, would be of value. Some results from experiments along these lines will be reported here. An internal friction measuring device was assembled mainly following a description by KG." The measurements were also carried out as reported in that paper. Table I gives the chemical compositions of the four different materials used in this investigation. All materials were drawn to wires with diameter about 0.8 mm, and the analyses refer to these final shapes. Determination of Nitrogen Peak Wires from steels A, B, and C were decarburized in wet hydrogen (about 30 pct H2O) at 700°C until no carbon or nitrogen could be found by chemical analysis. No peak was then found in the internal friction. The wires were further annealed at 580°C for 16 hr in hydrogen bubbled through a solution of 6.8 pct NH3 in distilled water. Chemical analyses gave 0.04 pct N in A and C, and 0.06 pct in B. After annealing at 580°C for 15 min in a lead bath and water quenching, the internal friction was immediately measured. The resulting curves are shown in Fig. 1. At these high values of the internal friction the accuracy is comparatively poor; at Q-1 - 0.030 it is estimated to be 0.002. In order to make possible a calculation of the activation energy for diffusion of nitrogen, measurements were made at two different frequencies. Steel A shows rather broad peaks, and their temperatures can hardly be expected to be very accurate. Steels B and especially C are better in this respect. The finding of Fast' that manganese broadens the nitrogen peak is con-

Jan 1, 1953

By A. L. Barnes

A number of reservoirs have been partially invaded by bottom water. Water flooding such reservoirs can be especially inefficient if the oil has a high viscosity because injected water will under-run the oil and emerge at producing wells without having displaced much oil. A possible means of improving water sweep efficiency would be to precede the water flood with a slug of water purposely thickened with a chemical additive. This possibility has been studied with a scaled laboratory flow model. The investigation was carried out on a model representing a 20-acre five-spot with one set of reservoir condition~. Displacements were performed with water, with viscous-water slugs of 10 and 25 per cent of the pore volume followed by water, and with all viscous water. Displacement tests were made at several rates of injection. For all cases, compared at the same producing water-oil ratio, an increase in rate resulted in an increase in volumetric sweep. The larger the quantity of viscous slug injected, the greater the crossflow of oil ahead of the displacing front and, thus, the lower the WOR during that period of a displacement. This investigation indicates that the injection of aqueous viscous slugs in this type of system would give some additional benefit over conventional flooding by (I) reducing the life of the flood, (2) reducing lifting costs and (3) increasing ultimate recovery. The benefits of a viscous-slug displacement would warrant its use if the viscous water could be created for a few cents per barrel. INTRODUCTION The most appropriate method for water flooding oil reservoirs which have been partially invaded by bottom water has been a problem of considerable interest. Such reservoirs, having good vertical permeability and unfavorable mobility ratios, are difficult to produce efficiently under normal waterflood procedures. Even though the injection wells have been plugged back above the oil-water contact and the water zone has been squeezed off, injection water will enter the formation and not only displace oil, but also much of it will displace the bottom water, thus creating a high producing water-oil ratio at the start of a flood (see Fig. 1). Since the rate of injection and the viscosity of the displacing fluid are the more easily controlled physical parameters of the reservoir, it is quite natural to study their effects on the volumetric sweep of the oil zone and on the producing water-oil ratio. Increasing the viscosity of the displacing fluid has two disadvantages—it reduces the maximum rate of injection into the reservoir, and it costs more than water. It was thought that the injection of a viscous-fluid slug, followed by water, would minimize these two disadvantages, increase the volumetric sweep of the oil zone and reduce the producing water-oil ratio. Water with an additive to increase viscosity would probably be the most effective. The primary purpose of this investigation was to determine the feasibility of injecting viscous-water slugs followed by water to improve or hasten oil recovery while reducing the producing water-oil ratios. The effect of injection rate upon recovery was also investigated. A laboratory model, scaled to a 20-acre five-spot prototype with one set of reservoir conditions, was constructed. Laboratory studies of displacements with (1) water, (2) viscous-water slugs of 10 and 25 per cent of the pore volume followed by water and (3) all viscous water were performed at several rates of injection. THEORY OF SAND MODEL SCALING There are two conventional means of determining scaling criteria. These are dimensional analysis and inspec-tional analysis. Determining scaling criteria by dimensional

By P. T. Carter, A. B. Murad, H. B. Bell

The distribution of manganese and oxygen between molten iron and FeO-MnO-SiO2 slags not saturated with SiO2 has been determined and used to calculate activities of MnO and SiO2 in MnO-SiO2 slags. These were found to be intermediate between the corresponding activities in FeO-SiO2 and CaO-SiO2 slags. THE equilibrium constant for the reaction between molten iron containing manganese and slags containing FeO and MnO, namely: FeO(slag) + Mn = MnO (slag) + Fe(1iquid) is most conveniently represented by: (MnO) Kmn== (FeOHMn] [Fe] is omitted, since for dilute solutions of manganese in iron, afe is approximately constant. When activities are used for (MnO), (FeO) and [Mn], Kmn is a true equilibrium constant and will apply to all types of slags, but when weight percentages are used, the values obtained for Kmn for different slags vary considerably. The equilibrium between iron containing manganese and relatively pure FeO-MnO slags has been investigated by several workers;1-4 the most recent investigation reported is that of Chipman, Gero, and Winkler.4 Their results, corresponding to slags containing up to 4 pct SiO2, were represented by the equation: 6440 log KMn = +2.95 In this case both slag and metal may be assumed to be ideal solutions, therefore the values of Kmn so derived represent the true constant for the manganese reaction. As the molecular weights of MnO and FeO are almost equal, weight concentration of these oxides may also be used in the above expression. Acidic oxides such as SiO2 and P2O5 affect the activities of FeO and MnO differently, so that when total concentrations by weight of FeO and MnO are used in the above expression for Kmn the values obtained are no longer constant. These will be denoted by K'mn. Körber and Oelsen5 investigated the manganese reaction using silica-saturated iron-manganese-silicate slags and found: 7940 logK'mn =3.172 This corresponds to Kmn values much higher than those obtained for pure oxide slags. The results of Körber and Oelsen, and Chipman, Gero, and Winkler are summarized in Table I. In the present investigation it was decided to study the manganese reaction using iron-manganese-silicate slags not saturated with silica, and which fell mainly between the orthosilicate join 2FeO . SiO2 - 2MnO.SiO2 and the FeO-MnO side of the ternary system FeO-MnO-SiO2. It has been shown" that the phases present in solidified slags of this part of the diagram are (FeO, MnO) and (2Fe0.Si02, 2Mn0-SiO,) solid solutions. Such an investigation would be of interest in deoxidation and also gives information on activities in liquid slags. This equilibrium has not as yet been investigated successfully. Hilty and Crafts7 attempted to examine this reaction in a rotating crucible furnace, but were unable to obtain suitable slag samples. In the present investigation one series of experiments was carried out in a rotating crucible furnace, because the success of Taylor and Chipman8 with such a furnace in their study of oxygen distribution between molten iron and (CaO, MgO) — FeO-Si0, slags suggested that it would minimize contamination of the slag by the crucible material. A second series was carried out using a wire-wound resistance furnace. Rotating Crucible Furnace Experiments In all cases the metallic charge consisted of 800 to 1000 g Armco iron containing 0.02 pct C, 0.03 pct Mn, and traces of Si. Manganese and silicon additions consisted of electrolytic manganese (99.9 pct)

Jan 1, 1953

By T. B. Massalski, C. S. Barett

THAT metals and alloys of the body-centered-cubic structure tend to become unstable at low temperatures is so nearly universal that any exceptions are worthy of special attention. Studies of the exceptions may disclose unrecognized examples of metastability or may shed light on the nature of some of the factors that stabilize the body-centered-cubic phase. Among the structurally analogous body-centered-cubic 3/2 electron compounds, the ß-phase in the Cu-Zn system deserves further attention for, although this phase is known to undergo partial mar-tensitic transformation on cooling below room temperature to the temperature of liquid nitrogen when the composition is less than about 42 wt pct Zn, it does not transform on cooling .when there is more than this amount of zinc present.1-4 The present authors recently found that an alloy containing 48.35 wt pct Zn could be transformed, however, if deformed severely at room temperature or lower temperatures.V his discovery led to the suggestion that the jerky flow of ß-brass single crystals6 and some of the unusual temperature variations of the yield strength and hardness are due to strain-induced transformation during the tensile tests. The present investigation is an extension of that work to cover the entire available range of compositions of Cu-Zn ß-phase alloys and certain interesting compositions of the ß-phase in the Cu-Zn-Ga system. Particular attention is given to the structure of the transformation product resulting from cold work, which is found to vary with alloy composition, and to the temperature range in which transformation can be induced in the various alloys. The composition limits of the body-centered-cubic phase in the Cu-Zn system, based on a recent review by Raynor7 and the precision determinations of Beck and Smith: are shown in Fig. la; in the ß region the alloys are disordered and in the ß region they are ordered. The rate of ordering is so rapid that a high degree of order is found in any of these alloys immediately after quenching. Experimental The nine binary and four ternary alloys of this investigation were prepared from cathode copper (99.99 pct purity), electrolytic zinc (99.99+ pct), and gallium (99.98+ pct). All alloys were cast in transparent Vycor tubing, homogenized at temperatures between 800° and 890°C, and quenched in water. Ternary alloys were cast in small amounts (-5 g) to predetermined compositions to fall along a line of constant electron concentration in the ternary system. Changes of weight during the casting operation of the ternary alloys were not greater than 1 part in 2500 from the intended nominal weights and therefore their compositions were accepted without chemical analyses. All binary alloys were cast in larger amounts (100 to 150 g), homogenized, and hot rolled after preheating to 800°C. The central portion of the rolled strip of each alloy was annealed for eight days and quenched in brine. All binary alloys were analyzed chemically. The compositions, heat treatments, and metallographic appearances of all alloys are tabulated in Table I. Various samples were subjected to heat treatment or cold work at several temperatures and were then examined metallographically or by means of X-rays. Specimens about 6x6x3 mm in size were examined metallographic ally to confirm the presence of the ß-phase after quenching. Cold work was introduced by fastening each sample between two pieces of steel, cooling the assembly to the desired temperature, and transfering it rapidly to a vise where moderate or severe compression was immediately applied. Cold working at liquid helium temperature was done by a chisel-shaped tool mounted on an X-ray spectrometer, described elsewhere.% A!! metal-

Jan 1, 1958

By P. B. Mee

The secondary re crystallization behavior of two vacuum-melted, nominally 3 pct Si-Fe alloys has been studied, one alloy being produced from pure electrolytic iron and semiconductor-grade silicon and the other from commercial-purity hot band. The vacuum-melted and vacuum-remelted alloys were found to develop {110}(hhl) and {lll)(hkl), respectively, on annealing in high vacuum and {100}(0kl) and {11l}(hkl), respectively on annealing in pure hydrogen of dew point, < — 60°C. H2S doping of the hydrogen or annealing in commercial argon was found to effect a reversal for the vacuum-remelted alloy from (111) to (100) secondary recrys-tallization, while prolonged vacuum annealing at 2 x 10-6 Tow resulted in a tertiary re crystallization from (111} to (110). The growth selection of the {lll}(hkl) component was found to be governed predominantly by the {111}/planar misorientation, the maximum deviation of the resulting secondaries being 5 deg. It is considered that the driving force for {111}(hkl) secondary recrystallization arises from the preferential lowering of ?111, possibly by phosphorus or nitrogen diffusion, just as oxygen and sulfur under certain conditions have been found to preferentially lower ?100. When heavily cold-rolled metals are annealed at high temperatures, primary recrystallization usually occurs rapidly and may be followed by considerable grain growth. However, in the presence of a fine dispersion of inclusions1"3 or with a strong matrix preferred orientation4&apos;&apos; the matrix may be stabilized and a secondary recrystallization may then be effected. Also, in vacuum-melted Si-Fe it has been shown possible to develop {100}(001) and {110}(001)6 surface energy driven secondary recrystallization textures. Further, it has been found that, on annealing very pure metals, grain growth normally ceases when a grain size approximately twice the strip thickness is acquired, due to the formation of V-shaped thermal grooves which result in an equilibrium being set up between surface and grain boundary stresses. If, however, a surface energy difference ??s, exists between adjacent grains (of the order of a few percent of the grain boundary energy ?b), then according to Mullins8 a secondary recrystallization may be effected, since the grains having lowest ?s would grow at the expense of their higher-energy neighbors. For clean bee metal surfaces ?110 should be lowest; however, for 3 pct Fe-Si (100) secondary structures have frequently been developed and have been attributed by Walter and Dunn9 to an alteration of the relative surface energies due to the preferential chemisorption of oxygen on (100) planes. Kohler,10 however, indicated that this reversal may be achieved by employing minute quantities of highly polar compounds in the annealing atmosphere, i.e., sulfur compounds, in par- ticular H2S being beneficial in (100) growth. This work has been verified by Kramer" using {100)/{110} bicrystals, while Mager12 demonstrated the importance of sulfur diffusion within the strip. Detert13 has intimated that carbon may be responsible for the preferential lowering of ?110 although no direct evidence has appeared yet to support this supposition. It must , be appreciated that the above-mentioned examples of surface energy driven secondary recrystallization were obtained with very pure vacuum-melted materials with oxygen contents (which is now known to be a critical factor") less than 35 ppm. During the course of a textural study on Si-Fe it has been found that under certain conditions (111) secondary recrystallization can be obtained by what is believed to be a surface energy growth selection mechanism. The purpose of the present paper is to briefly describe this result and to try and postulate the possible causes. EXPERIMENTAL Two vacuum-induction-melted, nominally 3 pct Si-Fe alloys were produced, one from pure electrolytic iron and semiconductor-grade silicon designated A and the other from commercial-purity hot band, designated B.

Jan 1, 1969

By M. T. Simnad, C. E. Birchenall, M. H. Davies

THE marker movements observed by Davies, Simnad, and Birchenall during the growth of magnetite on wustite have been misinterpreted. It is the purpose of this note to correct the original interpretation. In that investigation wustite specimens were prepared by oxidizing pure iron disks in water vapor until the iron was consumed. Argon was used as a carrier gas for the water vapor and on the complete conversion of the metal to its oxides (&apos;FeO&apos; plus a small amount (10 pct) of surface Fe3O) the water supply was bypassed and the specimens were annealed in argon alone in order to equilibrate the wustite with the overlying magnetite. After cooling, the magnetite was ground off, a crude magnetic test being employed to determine its complete removal. Radioactive silver streaks were then applied to the surface and the specimen was oxidized completely in water vapor to prevent hematite formation. After complete oxidation the markers were found to enclose about 80 pct of the magnetite with the other 20 pct lying outside the markers. This observation was interpreted to mean that oxygen transport was four times as great as iron transport during the growth of the magnetite. The conclusion would have been correct if, as in the case of wustite growing on iron, all the iron had started from one side of the marker and all the oxygen from the other side initially. Actually a material balance is required. For simplicity, take wustite to be exactly FeO, and magnetite to be Fe3O,. Then at the start of the reaction 3 FeO + O -> Fe,O., All of the iron and three-fourths of the oxygen of the final product will be within the marker inter- faces. The other fourth of the oxygen is in the gas phase outside the marker. From the experimentally determined final position of the markers simple calculation shows that one-fifth of the total iron has crossed the marker interface, while one-twentieth of the total oxygen has crossed in the reverse direction. The simplified result favors iron transport in the ratio four to one. However wiistite is not stoichiometric FeO. At 900°C, the temperature of the measurement, the composition is about FeO When the material balance for the same experimental result is repeated, assuming the product will be 1 mol of Fe3O4, it is found that 0.6 gram atoms of iron and 0.19 gram atoms of oxygen must have passed the marker in the same direction. (This is readily apparent from the reaction to form 1 mol of Fe3O4 SFeO The total oxygen supplied from the atmosphere is 0.61 gram atoms, but the iron which passes the marker interface, i.e., 0.6 gram atoms, requires 0.8 gram atoms of oxygen to convert it to Fe,O,.) If all the transport during magnetite growth is due to iron ion diffusion, then the marker would enclose about 85 pct of the final magnetite and the original measurement is in error by about 5 pct. This error is probably less than the uncertainty in locating the markers by autoradiography. The possibility also exists that the starting wustite was not quite saturated with oxygen and underwent further enrichment with consequent envelopment of the marker before magnetite caught up with the marker interface. In any case it appears that these measurements actually favor iron ion diffusion in magnetite overwhelmingly as the factor controlling its growth, although further experimental measurements are needed to eliminate the error in material balance described. Such studies are planned.

Jan 1, 1954

By J. L. Carne

ORE control is a matter of planning and supervision based on a foreknowledge of the content and distribution of ore. The Inspiration orebody is predominately a copper-sulphide blanket, overlain by an oxidized zone of copper silicates, copper carbonates, and barren capping. Most of the ore is treated by leaching, and the optimum requirement of this method is the goal toward which the mining schedule is aimed. Both open-pit operations and underground mining are used. The problems of ore control at Inspiration are: I—maintenance of metallurgical balance, 2—conservation of oxide ore, and 3—mining out of the orebody at an average grade which parallels that of the reserve figure. Prior to the fall of 1926 all of the Inspiration division ores were treated by flotation, but the mixed ores of the Live Oak—Keystone section carried too large a proportion of copper in the form of chrysocolla for satisfactory flotation. For this type of mixed ore the leaching process now in use had been worked out, and the plant was put into operation in the fall of 1926. The process is known as the ferric sulphate leach, and the leaching solvents contain both ferric sulphate and free sulphuric acid. Sulphide copper in the form of chalcocite is leached by the ferric sulphate, and the oxidized copper minerals are dissolved by the sulphuric acid. From the beginning of operations to the present time the plant has treated some 67 thousand tons of ore having an average copper content of 1.142 pct, of which 0.605 pct has been in the form of oxidized copper minerals. The plant is currently being operated at the rate of 11,500 tons per day, 7 days per week. However, this tonnage is produced in 6 days of mine operation. The average current grade is approximately 1 pct copper, of which about 50 pct is present as oxidized or acid-soluble copper. Close control of metallurgical procedures is a vital factor in operation of the plant and is in turn dependent upon careful regulation of feed. An excess of sulphide copper requires the presence of more ferric sulphate in the leaching solvents. On the other hand, an excess of ferric sulphate in the presence of a low sulphide feed seriously reduces the efficiency of electrolytic precipitation in tank house operations. This condition must be avoided at all costs. An additional factor must be considered. It is known that the sulphide content is predominant in the ore which remains in the reserve. To maintain the necessary sulphide-oxide proportion, so that the entire reserve will mine out at both a grade and a sulphide-oxide ratio that will be permissible throughout the remaining life of the property, it is obvious that the oxide reserve must be currently preserved to as great an extent as possible. Fortunately much of the oxide reserve is found in the open-pit operation. This happy circumstance adds flexibility to the procedure and makes it possible to maintain the close regulation necessary to insure best overall results, both mining and metallurgical. The two ore streams from the pit and underground operations join at the coarse-crushing plant, and proper control must be exercised before the ore reaches this point. The open pit is currently providing about 55 pct of the ore and underground operations the balance of production. Both operations are under a single superintendent so that the closely interrelated problems may be more readily controlled. The least flexible of the two producing units is the underground mine, where the mining method is block caving. Although a block of ground may be undercut and developed, characteristics of the material determine its caving action. The ore in the chutes must be drawn. The area currently mined from underground is in a zone predominately sulphide and is generally

Jan 1, 1953

By Norman F. Schulz, Emert W. Lindroos, Strathmore R. B. Cooke

DURING the course of an investigation of the effects of various starch products on hematite and quartz in regard to their separation by flotation, it was found that whereas most starches flocculated suspensions of hematite in water, they did not flocculate similar suspensions of quartz. However, a derivative of whole corn starch containing approximately one tenth aminoethyl group (-—CH,CH2NH2) per glucose unit proved to be an exception. This aminoethyl starch was a very good flocculant for both hematite and quartz, and also possessed the property of depressing both minerals in cationic flotation tests. In view of the widespread use of starch as a flocculating agent of solids in tailing water, pulps, and for coal slimes, ore and various other purposes in sulphide and nonsulphide flotation, attention is called to the effective surface activity of aminoethyl starch in flocculating suspensions of the two minerals investigated. Test Materials The starch products employed included Globe Pearl starch No. 144 and fresh aminoethyl starch, both supplied by the Corn Products Refining Co. Dr. A. L. Elder" has kindly furnished a description The minerals used in the various tests are listed in Table I. Their specific surfaces were determined by the air permeability method, which gave results reproducible to within plus or minus 3 pct. Surface areas obtained by krypton adsorption were greater than the air permeability values by a factor of 2.0 for quartz and 62.4 for hematite. Starch Adsorption on Mineral Surfaces Starch adsorption data were obtained by agitating for 1 hr measured volumes of neutral starch solutions of known concentrations with weighed quantities of finely divided mineral of measured specific surface. The mineral then was separated from the pulp liquor by centrifugation and the residual starch content determined by chemical analysis. The analytical procedure consisted of oxidizing the starch with an excess of dichromate in acid medium at elevated temperature and titrating the excess dichromate by the ferrous ammonium sulphate—potassium permanganate method. Analytical results were reproducible to within less than 1 pct. Adsorption data obtained in unbuffered solutions near the neutral point are plotted in Fig. 1. The adsorption on either mineral was far greater for the aminoethyl starch than for the Pearl starch. Flocculation The degree of flocculation was determined for a given pulp by measuring the time required for the supernatant liquid to reach a certain degree of clarity. This was accomplished by passing a standard light beam through the pulp, contained in a glass settling tube, and measuring the time required after agitation ceased for the intensity of the transmitted beam to reach a predetermined value. Starch reagent was added to each pulp in small uniform increments, and the settling time was determined after each such addition. Increase in pulp liquor volume due to the added starch reagent was ignored in these tests. Pulps were maintained at or near neutrality. of the preparation of the aminoethyl starch: "Three hundred and sixty grams of powdered unmodified corn starch was slurried in 3 liters of water and stirred during gelatinization. Eighty-six grams of ethylenimine was added slowly during reflux which was continued for 4 hr. The yellow solution set to a gel upon cooling. This was broken up and neutralized with HC1. The thick paste was dried on hot rolls. Adsorbed polyethylenimine and salts were removed from the yellowish products by washing first with acidified aqueous &apos;60 per cent&apos; alcohol. The white product contained nitrogen corresponding to about one aminoethoxy group per ten glucose residues." Only laboratory samples of this starch derivative have been prepared. The starch reagents for use in flocculation, flotation, and adsorption tests were made up by dispersing the appropriate quantities of air-dry starch in cold water, adding boiling water, and heating for 30 min at 120°C under pressure. When used ip adsorption tests, the starch solutions first were cleared of insoluble matter by centrifugation.

Jan 1, 1953

By Strathmore R. B. Cooke, Emert W. Lindroos, Norman F. Schulz

DURING the course of an investigation of the effects of various starch products on hematite and quartz in regard to their separation by flotation, it was found that whereas most starches flocculated suspensions of hematite in water, they did not flocculate similar suspensions of quartz. However, a derivative of whole corn starch containing approximately one tenth aminoethyl group (-—CH,CH2NH2) per glucose unit proved to be an exception. This aminoethyl starch was a very good flocculant for both hematite and quartz, and also possessed the property of depressing both minerals in cationic flotation tests. In view of the widespread use of starch as a flocculating agent of solids in tailing water, pulps, and for coal slimes, ore and various other purposes in sulphide and nonsulphide flotation, attention is called to the effective surface activity of aminoethyl starch in flocculating suspensions of the two minerals investigated. Test Materials The starch products employed included Globe Pearl starch No. 144 and fresh aminoethyl starch, both supplied by the Corn Products Refining Co. Dr. A. L. Elder" has kindly furnished a description The minerals used in the various tests are listed in Table I. Their specific surfaces were determined by the air permeability method, which gave results reproducible to within plus or minus 3 pct. Surface areas obtained by krypton adsorption were greater than the air permeability values by a factor of 2.0 for quartz and 62.4 for hematite. Starch Adsorption on Mineral Surfaces Starch adsorption data were obtained by agitating for 1 hr measured volumes of neutral starch solutions of known concentrations with weighed quantities of finely divided mineral of measured specific surface. The mineral then was separated from the pulp liquor by centrifugation and the residual starch content determined by chemical analysis. The analytical procedure consisted of oxidizing the starch with an excess of dichromate in acid medium at elevated temperature and titrating the excess dichromate by the ferrous ammonium sulphate—potassium permanganate method. Analytical results were reproducible to within less than 1 pct. Adsorption data obtained in unbuffered solutions near the neutral point are plotted in Fig. 1. The adsorption on either mineral was far greater for the aminoethyl starch than for the Pearl starch. Flocculation The degree of flocculation was determined for a given pulp by measuring the time required for the supernatant liquid to reach a certain degree of clarity. This was accomplished by passing a standard light beam through the pulp, contained in a glass settling tube, and measuring the time required after agitation ceased for the intensity of the transmitted beam to reach a predetermined value. Starch reagent was added to each pulp in small uniform increments, and the settling time was determined after each such addition. Increase in pulp liquor volume due to the added starch reagent was ignored in these tests. Pulps were maintained at or near neutrality. of the preparation of the aminoethyl starch: "Three hundred and sixty grams of powdered unmodified corn starch was slurried in 3 liters of water and stirred during gelatinization. Eighty-six grams of ethylenimine was added slowly during reflux which was continued for 4 hr. The yellow solution set to a gel upon cooling. This was broken up and neutralized with HC1. The thick paste was dried on hot rolls. Adsorbed polyethylenimine and salts were removed from the yellowish products by washing first with acidified aqueous &apos;60 per cent&apos; alcohol. The white product contained nitrogen corresponding to about one aminoethoxy group per ten glucose residues." Only laboratory samples of this starch derivative have been prepared. The starch reagents for use in flocculation, flotation, and adsorption tests were made up by dispersing the appropriate quantities of air-dry starch in cold water, adding boiling water, and heating for 30 min at 120°C under pressure. When used ip adsorption tests, the starch solutions first were cleared of insoluble matter by centrifugation.

Jan 1, 1953

By Paul B. Crawford, Bobby L. Landrum

Electrical model studies have been made of the effect of drainhole drilling on production capacity. Drain holes are those lateral holes which are sometimes drilled to assist in increasing the oil drainage into the main wellbore. The studies indicate that if the drainhole length i.r near 0.2 of the drainage radius, the increase in production capacity may be approximately 1.8, 2.08, trnd 2.33 for the case of one, two and four drain holes, respectively. If multiple drain holes are drilled, shorter holes are required to achieve a specific increase in production capacity than if one or two holes are drilled. To achieve increases in production capacities by factors near three it is shown that the drainhole lengths divided by the drainage radii must be approximately 0.64, 0.48, cnd 0.37 for the case of one, two and four drain holes, respectively. IN T RO DUCTION Kecent developments in drilling techniques have permitted the drilling of lateral or horizontal holes to increase the rate of production. The number of these drain holes may vary from 1 to 10, and they have been drilled laterally as much as 100 ft. Drainhole drilling at substantial depths is of recent origin but has been used in the Spraberry field of West Texas, the La Pas field in Western Venezuela, and certain fields in California. The diameter of the drain holes has been approximately 6 in. In drilling drain holes it is desired to know how much increase in production capacity may be expected, what additional benefit may be gained by drilling more than one drain hole, and what increase in production capacity may be brought about by lengthening the existing drain holes. In realization of the importance of lateral drilling, electrical model studies were made to provide quantitative estimates on the effect of drain holes on production capacity. ANALYSIS An electrical model was used in studying this problem. A wooden circular reservoir approximately 30 in. in diameter and 2 in. deep was filled with a dilute salt solution to a depth of 1 in. A copper band formed the periphery of the tank, and a copper wire was inserted in the center of the tank to represent the well. The drainage radius divided by the well radius was equal to 500. A diagram of this type model is shown in the inset of Fig. 1. An electrical potential was applied to the wire well and copper band at the periphery to determine the flow of current. Following this measurement copper wires of various length were soldered to the vertical wire well in such a manner as to simulate lateral wells drilled into the reservoir. Multiple lateral holes of various lengths were studied by varying the number and length of copper wires soldered to the vertical wire well. All multiple lateral wells were located symmetrically about the vertical well. The effect on production capacity by drilling an infinite number of lateral holes was studied by replacing the lateral hole with a copper disk. For each condition the flow of current was measured and compared with the flow of the vertical well only. The model which is thus described provides the steady state increases in production capacity which may be expected in some cases. The data conform to those which would be observed for a uniform homogeneous reservoir. The data may have primary application to those reservoirs producing above the bubble point. It is realized that few lateral holes are drilled in reservoirs of this type, but the data may be of some value in guiding future work or aiding to explain observed phenomena.

Jan 1, 1956

By G. S. Coe, G. F. Bolling

The columnar-to-equiaxed transition (CET) has often been studied as a function of concentration, C, temperature gradient in the melt, G, and rate of solidification, R. Although it may not be immediately obvious it is sure that the CET, expressed as some ratio G/R necessary to suppress equiaxed nucleation for a given C,&apos; cannot be a single-valued function of C. This restriction which is ignored in theoretical presentations is most trivially illustrated by the following simple reasoning. An ordinary casting is an unconstrained system where the thermal conditions change continuously with progressive solidification, and thus where the ratio G/R decreases from the outset. A CET occurring early in a casting (much equiaxed material) must then mean a higher value of G/R at transition, in comparison with the late CET which implies a more columnar ingot. Therefore, when we choose to experiment under constant superheat for all alloys across the simplest binary, and we find an inversion in the amount of equiaxed material, we shall find two values of C satisfying the G/R condition. However, in addition to this simple instance, the early experiments of ~orthcott&apos; seem to show that the amount of equiaxed material in cast ingots may be a multivalued function of composition in a given binary system. In the present investigation, the CET has been examined in Pb-Sb, Pb-Ag, Pb-Sn, and Sn-Pb under several types of casting conditions. First, we have used the "bidirectional" ingot section Simulation;~ and we have used .&apos;i~z situ" ingot solidification where a hot mold already filled with liquid is chilled so that there is no disturbance provoked by pouring. Differences in method are trivial to our purpose except for the fact that certain variations are more simply observed by one technique than by the other. Second, we have varied the mode of superheating from the simple extreme of casting all alloys from the same temperature regardless of composition to the careful casting at a standard superheat, calculated with respect to the alloy liquidus. Third, we have made provisions for decanting and interface observation, so that some "castings" were not completed. The results obtained with Pb-Sb are exemplary; some of these are shown in Fig. 1 along with explanatory captions. At 9 to 10 at. pct Sb, and thus above the solid-solubility limit Cs = 5.8 at. pct Sb and yet below the eutectic concentration Ceu = 17.5 at. pct Sb, there is a persistent anomaly in all the variations. Measurement was easy enough and standard enough so that we may forgo discussion of either method or possible error, in view of the forceful self-consistency shown by experiment. Solute distributions were measured along the bidirectional ingots in order to determine if a solute buildup had occurred at the CET. No anomalous changes in concentration were observed along the bars at either side of the solute anomaly of 10 at. pct Sb. The microstructures of the ingots were also examined across the range of composition investigated. At concentrations less than 9 at. pct Sb the micro- and macrostructures were typical of the cellular-dendritic growth usually reported for the columnar zone. Above the anomaly, both the columnar grain size and the amount of primary phase decreased. This microstruc-tural observation can be correlated with observations made of decanted interfaces. Below 9 at. pct Sb, the interface reveals the "normal" columnar dendritic structure; however above the anomalous concentration range, preferential growth of certain dendrites appears to form a "super dendrite" pattern. In Fig. 2 a microstructural view of the etched &apos;(super dendrites&apos;&apos; shows their constitution both in terms of relative phase proportion and in terms of the ordinary smaller dendrites.

Jan 1, 1969

By J. L. Carne

ORE control is a matter of planning and supervision based on a foreknowledge of the content and distribution of ore. The Inspiration orebody is predominately a copper-sulphide blanket, overlain by an oxidized zone of copper silicates, copper carbonates, and barren capping. Most of the ore is treated by leaching, and the optimum requirement of this method is the goal toward which the mining schedule is aimed. Both open-pit operations and underground mining are used. The problems of ore control at Inspiration are: I—maintenance of metallurgical balance, 2—conservation of oxide ore, and 3—mining out of the orebody at an average grade which parallels that of the reserve figure. Prior to the fall of 1926 all of the Inspiration division ores were treated by flotation, but the mixed ores of the Live Oak—Keystone section carried too large a proportion of copper in the form of chrysocolla for satisfactory flotation. For this type of mixed ore the leaching process now in use had been worked out, and the plant was put into operation in the fall of 1926. The process is known as the ferric sulphate leach, and the leaching solvents contain both ferric sulphate and free sulphuric acid. Sulphide copper in the form of chalcocite is leached by the ferric sulphate, and the oxidized copper minerals are dissolved by the sulphuric acid. From the beginning of operations to the present time the plant has treated some 67 thousand tons of ore having an average copper content of 1.142 pct, of which 0.605 pct has been in the form of oxidized copper minerals. The plant is currently being operated at the rate of 11,500 tons per day, 7 days per week. However, this tonnage is produced in 6 days of mine operation. The average current grade is approximately 1 pct copper, of which about 50 pct is present as oxidized or acid-soluble copper. Close control of metallurgical procedures is a vital factor in operation of the plant and is in turn dependent upon careful regulation of feed. An excess of sulphide copper requires the presence of more ferric sulphate in the leaching solvents. On the other hand, an excess of ferric sulphate in the presence of a low sulphide feed seriously reduces the efficiency of electrolytic precipitation in tank house operations. This condition must be avoided at all costs. An additional factor must be considered. It is known that the sulphide content is predominant in the ore which remains in the reserve. To maintain the necessary sulphide-oxide proportion, so that the entire reserve will mine out at both a grade and a sulphide-oxide ratio that will be permissible throughout the remaining life of the property, it is obvious that the oxide reserve must be currently preserved to as great an extent as possible. Fortunately much of the oxide reserve is found in the open-pit operation. This happy circumstance adds flexibility to the procedure and makes it possible to maintain the close regulation necessary to insure best overall results, both mining and metallurgical. The two ore streams from the pit and underground operations join at the coarse-crushing plant, and proper control must be exercised before the ore reaches this point. The open pit is currently providing about 55 pct of the ore and underground operations the balance of production. Both operations are under a single superintendent so that the closely interrelated problems may be more readily controlled. The least flexible of the two producing units is the underground mine, where the mining method is block caving. Although a block of ground may be undercut and developed, characteristics of the material determine its caving action. The ore in the chutes must be drawn. The area currently mined from underground is in a zone predominately sulphide and is generally

Jan 1, 1953

By G. C. Wallick, J. S. Aronofsky

This paper presents an experimental verification of numerical solutions of the differential equation describing the transient flow of an ideal gas through a porous material including gas slip effects. Several experiments previously proposed by one of the authors are described together with the correlation of the experimental results with the numerical solutions. Excellent agreement is shown between experiment and theory, thus demonstrating the validity of both the basic assumption made in the derivation of the differential equation and of the numerical solutions of the differential equation. INTRODUCTION In a recent paper,&apos; one of the authors has discussed a numerical solution of the differential equation describing the unsteady flow of an ideal gas through a porous material. This paper was primarily concerned with the effect of gas slip on the flow behavior. In steady state measurements, Klinkenberg2 and others have observed that the apparent gas permeability Kn of a porous material may be expressed as a linear function of the reciprocal average pressure 1/P of the form, ka = b + m/P........(1) where the intercept b is a constant for a given porous material and the slope m is a constant for a given porous material-gas combination. Aronofsky1 assumed that Equation (1) could be used to describe transient flow if P was replaced by the average pressure in an infinitesimal volume element. A number of numerical solutions of the resultant differential equation were presented and specific flow experiments were proposed as a means of testing the numerical solutions. The purpose of the present paper is to describe the results of several of these experiments and the correlation of the experimental data with the results of the numerical analysis. Reference should be made to the previous paper&apos; for details of the mathematical and numerical analysis. EXPERIMENTAL PROCEDURE A simplified schematic drawing of the experimental apparatus is shown in Fig. 1. An 8.89 cm diameter limestone core of length L = 14.82 cm was mounted in a conventional rubber sleeve permeameter cell. The external sleeve pressure in this cell was maintained equal to 500 psig during all experimental tests, thus permitting only longitudinal flow through the core. One end of the core, X = L, was connected to an adjustable cavity of volume V as well as a pressure gauge or manometer. The other end of the core, X = 0, was connected to a Nullmatic pressure regulator which was in turn connected to a nitrogen cylinder or vacuum pump. In each experiment, the core and adjacent dead volume were charged with nitrogen to a uniform gas pressure P1. The pressure at X = 0 was then suddenly raised or lowered to a constant pressure P, and the resulting pressure buildup or pressure decline at X — L was recorded as a function of the time. The porosity + and the permeability constants m and b were determined using the transient method which was suggested by the results of the numerical analysis and which was described in the earlier paper.&apos; The following average values for these constants were obtained as a result of 19 separate evaluations: 171 -0.259 2 0.005 md-atm; b = 0.374 5 0.008 md; and F = 0.098 ± 0.005*. It should be noted that in order that transient phenomena will be slow enough to be observed conveniently, it is desirable to use a porous material of very low permeability, e.g., less than I md. Moreover, it is in this low permeability range that the gas slip effects are most significant. Thus, such a low permeability sample is very suitable for use in an experimental verification of the numerical solutions previously described.

Jan 1, 1955

By T. J. Koppenaal

The surface slip line structure has been investigated by optical microscopy during the easy glide deformation of Cu-A1 single crystals as a function of composition, testing temperature and prior thermal treatment. The slip line structure in alloys of 2.5 or less at. pct Al is similar to pure copper, while alloys of 5 or more at. pct Al show slip tracings typical of a brass. Cross slip is observed in the "a-brass type" crystals and the amount of this type of slip increases rapidly with aluminum content. The cross slip tendency in 14 at. pct Al crystals is signicantly higher when tested at 150°C as compared to 4.2" and 77°K. In addition, cross slip is more pronounced in this alloy in the furnace cooled condition than when quenched from 450°C. The cross slip behavior is analyzed in terms of existing models for this type of deformation. In two previous investigations, reports of yield points1 and solid solution strengthening2 in Cu-A1 single crystals have been given. This paper enlarges upon the brief description of the slip line structure discussed in these reports. Since the easy glide slip line pattern of copper changes markedly with the addition of -30 pct Zn (-brass),3 a study of slip lines as a function of solute additions in Cu solid solutions should help to explain some of these differences. In addition to composition variables, slip lines have also been studied as a function of testing temperature and prior thermal treatment. PROCEDURE The slip line observations were made on single crystals of 0.5 to 14 at. pct Al using a light microscope. Details concerning the preparation and basic testing procedure are given elsewhere.&apos; Prior to testing, each crystal was homogenized at 900°C for 24 hrs, furnace cooled, and electrolytically polished in a 60 pct phosphoric acid solution. The strain rate was-5 X 10 sec-I in each case. Unless otherwise stated, all observations reported upon here were made during the early stages of easy glide. RESULTS AND DISCUSSION The maximum magnification generally used was 1000X, and slip lines could be resolved down to about 105 cm (1000A). This resolution is appreciably less than obtainable with electron microscopy replica techniques where the replication can resolve slip lines down to about 40 A. Thus, while many qualitative features could be studied, the type of quantitative data obtainable with an electron microscopy replica study could not be made. Crystals containing 0.5 and 2.5 at. pct Al deform much like pure copper exhibiting a high density of fine slip lines that cover the entire gage length of the specimens. Fig. 1 shows the surface slip line pattern in a 2.5 at. pct A1 extended 0.01 shear strain at room temperature. Crystals having 5 to 14 at. pct A1 showed appreciably coarser slip lines that were generally concentrated at one end of the gage length. During easy glide these coarse slip lines propagate along the gage length in a manner similar to that observed in a-brass single crystals by Piercy, Cahn, and cottrel14 and refered to by them as a Lüders band propagation. Fig. 2 shows a typical area of these coarse slips in a 14 at. pct A1 crystal after a room temperature shear strain of 0.01. Two slip systems were apparently active. Using a method described by Cullity, the angles, between the specimen axis and the normals of the primary and secondary slip planes were determined to be 50 and 84 deg, respectively. &apos;From the Laue photograph, was 52, 81, 66, and 30 deg for the primary, cross, conjugate, and fourth slip planes, respectively. The secondary active plane in Fig. 2 is thus established as the cross slip plane, and the operative slip system is evidently the cross slip system, e.g., slip

Jan 1, 1963

By J. B. Cheatham

Applications of the mathematical theory of plasticity promises to lead to the solution of many drilling and rock mechanics problems. ,Because of mathematical considerations, the inelastic behavior of rock has frequently been represented by a perfectly plastic model in conjunction with a yield criteria of the Coulomb or Mohr type. The totality of all stress states for which a solid ceases to behave elastically can be represented as a limit surface in stress space. ,Probing of such limit surfaces indicates details of strain hardening which are not provided by the standard triaxial testing procedure. Probing tests of the limit surfaces have been performed on Cardova Cream limestone to provide data for extending plasticity theory to cover situations in which consolidation and strain hardening are present. Test results indicate that this highly porous limestone undergoes a permanent volume decrease when it is subjected to hydrostatic pressures in excess of 3,500 psi. A virgin sample tested under a confining pressure of 1,500 psi has a yield strength of 1,700 psi; however, if the sample is subjected to a consolidation pressure of 5,000 psi, before testing at 1,500 psi, the yield strength is raised to 2,300 psi. Thus, both consolidation and strain hardening are important considerations in describing the mechanical behavior of this limestone. Tests conducted with the axis of the core having different orientations indicate that this rock is also anisotropic. Portions of the initial and subsequent limit surfaces are determined for samples loaded either perpendicular or parallel to the bedding planes. INTRODUCTION Previous experimental work in rock mechanics indicates that no mathematically tractable constitutive theory is inclusive enough to describe the mechanical behavior exhibited by all types of rocks under all conditions of stress and temperature. Indeed, the type of deformation encountered in a single type of rock is known to depend upon the stress and temperature conditions in the rock during deformation.l-5 Certain rocks and minerals, notably those minerals composed of ionic salts, have been shown to exhibit plastic deformation when tested under conditions of high confining pressure.2 Since the mathematical theory of plasticity provides simplifications over the theory of elasticity in certain types of problems, such as those in which limit analysis can be applied, it is of interest to know under what conditions plasticity theory may be applied to rock mechanics problems. The following factors determine the nature of the deformation a particular specimen will undergo: (1) the microscopic structure of the rock, i.e., the structure visible under an optical microscope, including number of phases, porosity, distribution of phases, (2) the mineralogical structure of the solid phases, (3) the conditions of stress and the rate of change of stress and (4) the temperature. Extensive experiments on Yule marble, Carthage marble, Solenhofen limestone and other calcerous rocks indicate that these relatively nonporous rocks deform plastically under certain conditions of loading, and creep under other conditions of loading.l-3 This study is concerned with the behavior of Cordova Cream limestone (Austin chalk) which is also composed almost entirely of calcite and thus has the same mineralogical composition but, because of a rather large porosity, it possesses a different microscopic structure. This investigation was undertaken to learn if Cordova Cream limestone deforms plastically despite the embrittling effect of the pore spaces, and to provide data which can be used to determine whether the mathematical theory of plasticity can describe the mechanical behavior of Cordova Cream limestone. A brief discussion is given of some of the underlying principles of plasticity theory concerning stress space and limit surfaces. Strain hardening is defined and a discussion is given of how the mechanical behavior of a material can depend on the previous history of the loading. This is followed by a description of the experimental procedures