Search Documents

By W. B. Mather

A RKANSAS is not only a geologist's paradise, but Ait is also particularly fortunate in possessing a wide variety of mineral resources. The future mineral production and mineral industry of Arkansas, like the other states in Mid-America, will probably depend to a large degree on efforts to increase the exploitation of the non-metalliferous deposits of the state. The term nonmetalliferous, as used in this paper, embraces all types of mineral deposits, except fuels, water, and those deposits from which, after bene-ficiation, metals are ultimately derived. For example, bauxite is the ore of aluminum, but a considerable portion of the bauxite mined eventually is employed in the production of nonmetallic alumina, an important oxide in the abrasive and ceramic industries. The bulk of the production, however, becomes metallic aluminum and therefore this type of mineral resource is considered metalliferous and is omitted from this paper. Arkansas' nonmetalliferous deposits are of many different types, too numerous to discuss in detail in a single paper; therefore, only their salient features are presented. Many types of deposits such as limestone, glass sand, novaculite, shale, and sandstone are exposed over wide areas, providing inexhaustible reserves. Other types of deposits, such as barite and tripoli, contain large reserves which certainly are not unlimited. Still other types of deposits, such as celestite, kaolin, and vermiculite, appear to occur in small isolated deposits containing relatively small reserves. Of course, all of Arkansas' nonmetalliferous deposits probably have not as yet been recognized, nor have all of the known deposits been prospected, tested, and evaluated. Various types of deposits are too low grade or too limited in extent to be profit- ably produced by today's standards. In the case of other deposits, the known uses are few in number, thus acting as a retarder to their development. Due to anticipated technologic advancements, the future demands of industry are not expected always to be the same as they are today, and therefore idle deposits or those of current limited production may readily become the important revenue producers of the future. The types of nonmetalliferous deposits discussed here include: clays, shales, and slates; silica deposits including glass sand, novaculite, tripoli, sandstone, chert, and quartz crystals; limestone and dolomite; barite; gypsum; celestite; nepheline syenite; green-sand; phosphate; vermiculite; fuller's earth; ben-tonite; diamonds; sand, and gravel. The location of the various types of deposits are presented on the accompanying map (fig. 1). Symbols indicate the general area of occurrence. Many deposits, such as limestone, shale, novaculite, and so on, are represented by formations which could only be properly shown on a geological map. In these instances only active deposits or those of exceptional merit are indicated by symbols on the map. A general northeast-southwest line divides the interior highland from the Gulf Coastal and Mississippi Alluvial Plains of south and east Arkansas. The data presented in this paper are only a surnmary of a portion of a more comprehensive survey and study of the natural resources of the entire state.' The study was sponsored and underwritten by the Arkansas Power and Light Co., Little Rock, as a public service to the state and its residents. Permission to present some of the data and conclusions resulting from the survey is gratefully acknowledged. Table I, prepared by the Arkansas Geological Survey from state severance tax records, presents the annual production secured from Arkansas nonmetalliferous mineral deposits. Clays, Shales, and Slates Clays: It is realized that each method of classifying clays is prone to criticism. In this paper, Arkansas' clays of potential value are arbitrarily

Jan 1, 1951

By W. B. Mather

A RKANSAS is not only a geologist's paradise, but Ait is also particularly fortunate in possessing a wide variety of mineral resources. The future mineral production and mineral industry of Arkansas, like the other states in Mid-America, will probably depend to a large degree on efforts to increase the exploitation of the non-metalliferous deposits of the state. The term nonmetalliferous, as used in this paper, embraces all types of mineral deposits, except fuels, water, and those deposits from which, after bene-ficiation, metals are ultimately derived. For example, bauxite is the ore of aluminum, but a considerable portion of the bauxite mined eventually is employed in the production of nonmetallic alumina, an important oxide in the abrasive and ceramic industries. The bulk of the production, however, becomes metallic aluminum and therefore this type of mineral resource is considered metalliferous and is omitted from this paper. Arkansas' nonmetalliferous deposits are of many different types, too numerous to discuss in detail in a single paper; therefore, only their salient features are presented. Many types of deposits such as limestone, glass sand, novaculite, shale, and sandstone are exposed over wide areas, providing inexhaustible reserves. Other types of deposits, such as barite and tripoli, contain large reserves which certainly are not unlimited. Still other types of deposits, such as celestite, kaolin, and vermiculite, appear to occur in small isolated deposits containing relatively small reserves. Of course, all of Arkansas' nonmetalliferous deposits probably have not as yet been recognized, nor have all of the known deposits been prospected, tested, and evaluated. Various types of deposits are too low grade or too limited in extent to be profit- ably produced by today's standards. In the case of other deposits, the known uses are few in number, thus acting as a retarder to their development. Due to anticipated technologic advancements, the future demands of industry are not expected always to be the same as they are today, and therefore idle deposits or those of current limited production may readily become the important revenue producers of the future. The types of nonmetalliferous deposits discussed here include: clays, shales, and slates; silica deposits including glass sand, novaculite, tripoli, sandstone, chert, and quartz crystals; limestone and dolomite; barite; gypsum; celestite; nepheline syenite; green-sand; phosphate; vermiculite; fuller's earth; ben-tonite; diamonds; sand, and gravel. The location of the various types of deposits are presented on the accompanying map (fig. 1). Symbols indicate the general area of occurrence. Many deposits, such as limestone, shale, novaculite, and so on, are represented by formations which could only be properly shown on a geological map. In these instances only active deposits or those of exceptional merit are indicated by symbols on the map. A general northeast-southwest line divides the interior highland from the Gulf Coastal and Mississippi Alluvial Plains of south and east Arkansas. The data presented in this paper are only a surnmary of a portion of a more comprehensive survey and study of the natural resources of the entire state.' The study was sponsored and underwritten by the Arkansas Power and Light Co., Little Rock, as a public service to the state and its residents. Permission to present some of the data and conclusions resulting from the survey is gratefully acknowledged. Table I, prepared by the Arkansas Geological Survey from state severance tax records, presents the annual production secured from Arkansas nonmetalliferous mineral deposits. Clays, Shales, and Slates Clays: It is realized that each method of classifying clays is prone to criticism. In this paper, Arkansas' clays of potential value are arbitrarily

Jan 1, 1951

By Robert G. Johnson, Richard J. Prosen

THE present work was done in connection with a program for investigating metal-to-ceramic braze techniques using the well-known reactivity of titanium with certain ceramic oxides. The investigation extended over the range of 0 to 30 pct Ti. The indium was obtained from the Indium Corp. of America and was specified to be 99.97 pct pure. The titanium was supplied by Metals Disintegrating Co. and was stated to be 99.5 pct pure. Each 2 to 4 g quantity of the alloy compositions studied was prepared using a mixture of 300 mesh powders pressed into pellet form. The pellets were heated in thin-walled molybdenum crucibles using a resistance-wound furnace in a vacuum less than 10-4 mm of Hg. Little reaction occurred between the molten alloy and the crucibles at the temperatures and short time intervals used. Only slight spectroscopic traces of molybdenum were found in the melt after a typical period of heating. The points shown on the phase diagram of Fig. 1 represent thermal arrest measurements. The phase boundaries shown are consistent with the thermal arrest and X-ray data obtained. The temperatures were determined using a Pt-Pt 10 pct Rh thermocouple with the junction spot-welded to a short molybdenum rod. The rod was almost completely immersed in the liquid metal, so that good thermal contact with the melt was achieved. The small mass of the crucible and its contents made it possible to obtain many heating and cooling curves in a few minutes time, an advantage which helped to minimize the effects of indium evaporation at the higher temperatures. A Brown strip chart recorder was used to display the thermal arrest curves. To check the technique, the melting point of 99.999 pure Al was measured and found to be within 1 of 660.2c, the accepted melting point. The upper limit of temperature with this technique was about 900°C beyond which the evaporation rate of indium became great enough to alter appreciably the alloy composition during the runs. A peritectic transition was found at 796°+ 5°C from 1.5 to 30 wt pct Ti. It was not found at 0.5 or 1.0 pct. A small super-cooling effect was observed. The melting-point transition to the B + L phase was found up to 20 pct Ti but not at 25 pct. Within the 1 deg accuracy of the measurement, the transition temperature was that of pure indium, 156°C. The liquidus line to the left of the 1.5 titanium point was located only approximately. The two crossed circle points at 1.0 and 0.5 pct Ti place a lower limit on the liquidus line and were determined by observing visually the cessation of vibrations in the melt caused by the damping effect as B-phase crystals were formed during cooling. The B-phase boundary was found at 23.8 pct Ti by X-ray analyses of small single crystals of the B phase isolated from 2 pct Ti melts. The compound was found to be Jetragonal with lattice dimensions of c = 3.052A and a = 10.094W. From the unit cell dimensions and the measured density of 6.42 i 0.05 g per cc, the compound was determined to be In4Ti3 which has 23.8 pct Ti. The calculated density of 6.44 g per cc is obtained assuming 2 mol

Jan 1, 1962

By H. R. Ogden, E. S. Bartlett, A. G. Imgram

Notched and unnotched tensile specimens of wrought and recrystallized, oxygmted and hydro-genated tantalum and columbium were tested over a range of temperatures selected to encompass the ductile-to-brittle transition. Increasing the oxygen content of tantalum and columbium increased their strength, and raised their ductility transition temperature, but did not cause a marked deterioration of notch properties below that of commercially pure material. The adverse effects of oxygen were more pronounced for recrystallized structures than for wrought material. The effects of hydrogen are complicated by strain aging or slow strain rate hydrogen embrittlement at -105°F. However, in general, hydrogen had only a minor effect an strength, but markedly increased the effective transition tem-terature and caused a deterioration of notch properties . BCC metals including the refractory metals in Groups Va and VIa (V, Cb, Ta and Cr, Mo, W) can be expected to undergo a ductile-to-brittle transition and exhibit brittle fractures at low temperatures.' Notch embrittlement is associated with this phenomenon, and can be a serious design problem. Table I compares the tensile transition behavior and notch sensitivity of commercially pure Group Va and VIa refractory metals. The Group VIa refractory metals have considerably higher transition temperatures, and become notch sensitive at higher temperatures, than do the Group Va refractory metals. In addition, the Group VIa refractory metals are sensitive to metallurgical structure. Recrystallized structures generally have higher transition temperatures than wrought material of the same composition. The relatively poor transition behavior of the recrystallized structures of these metals is generally attributed to the segregation of interstitial impurity atoms at grain boundaries. Pronounced sensitivity to structure is not evident with commercially pure Group Va refractory metals, however. Since these metals have higher solubilities for interstitial elements than do the Group VIa metals ,4 it can be expected that higher total interstitial concentrations are necessary to develop a comparable degree of grain boundary segregation and to produce a similar sensitivity of transition temperature to structure. Increasing only the concentration of interstitial atoms in solution would tend to increase the flow stress of a metal in relation to its cleavage fracture stress and thereby raise its transition temperature, but would not be expected to cause a marked sensitivity of transition temperature to structure. A research program has been conducted at the Battelle Memorial Institute to evaluate the effects of interstitial oxygen and hydrogen on the transition behavior and notch sensitivity of tantalum and columbium, and to evaluate the effects of structure on "contaminated" material. EXPERIMENTAL PROCEDURES Notched and unnotched tensile specimens of oxygenated and hydrogenated tantalum and columbium with both wrought and recrystallized structures were tested over a range of temperatures selected to encompass the ductile-to-brittle transition Oxygen levels selected for study in both tantalum and columbium were nominally 500 and 1000 ppm, whereas nominal hydrogen contents were 150 and 500 ppm in tantalum and 150 and 300 ppm in columbium. Oxygen and hydrogen additions were made directly to 6-in. lengths of 1/2-in.-diam electron beam melted wrought bar stock, in a Sieverts Apparatus. Subsequent high-temperature annealing was required for homogenization of the oxygenated material, but was not necessary in the case of hydrogenated stock. The oxygenated and hydrogenated bars were then swaged to 1/4-in.-diam rods. Tensile specimen blanks were cut from the 1/4-in.-diam rods and annealed to achieve stress-re-

Jan 1, 1963

By B. S. Butler

AN understanding of mineralizing solutions and how they carry and deposit metals is of prime importance to students of ore deposits. Lindgren states: "The whole problem surely is very complicated. One difficulty is that we know so little about the stability field of ore minerals."1 Lindgren further states: It is believed that they [the solutions] were in small part oxidized to sulphates, for instance, but in large part they were composed of hydrogen sulphide, alkaline sulphides and various halogen compounds. Doubtless, however, free carbon dioxide was present. Becker's view of the double sulphides as important constituents of the solutions probably holds good. In the fourth edition of Mineral Deposits2 Lindgren had changed his views somewhat: From the work of Day, Allen, Shepard, and others, it would seem probable that many of the volcanic gases are acid when given off but are in unstable equilibrium, and could not have preserved this acid character after having been long in contact with the surrounding rocks. It is believed that they were in small part oxidized to sulphates, for instance, but in larger part they were composed of hydrogen sulphides, alkaline sulphide, and various halogen compounds. Doubtless, however, free carbon dioxide was present. Becker's view of double alkaline sulphides as important constituents of the solution probably holds good. The writer wonders if progress would not result from an attack on the problem in steps, the steps to contribute to the attack on the whole. The initial step would deal with the simpler bodies of supposed magmatic (hydrothermal) origin, that is, those composed essentially of silicates, oxides, sulfates, and sulfides. The following discussion attempts to develop one step of a method that was proposed on a more comprehensive scale in 1929 by the writer and W. S. Burbank.3 The accompanying partial table (Table I) of the electromotive series is from a table distributed by Merck & Co. Inc., manufacturing chemists, prepared in turn from Fundamental Chemistry.& The electromotive arrangement brings together elements that in hypogene ore deposits occur: 1) in oxygen combination only; 2) in combination with sulfur as well as with oxygen; and 3) as sulfides, arsenides etc., and as native metals, see Table 11. The writer clearly recognizes that he is not qualified to discuss the formation of ore deposits as a chemical problem, but he feel that some of the relations that are met by the geologist can well be stated with the hope that the chemical explanation will be forthcoming. By consideration of a group including mainly the elements oxygen, hydrogen, sulfur and iron, complications are avoided, especially with elements of the lower electromotive group. The results can only contribute to the solution of the problem, not to the completion of it. The pH and Eh of the solutions and also temperature probably determine what minerals form. The mineral groups that contain elements high in the electromotive series are alumino-silicates, titanites, simple silicates, spinels, oxides, carbonates and sulfates, in all of which the elements are combined with oxygen. These groups are also recognized as the general order of temperature at which the minerals start to form, see Table 11. At low temperature are sulfides, arsenides, antimonides, sulfo-salts, and native metals, in all of which the elements are characteristically not combined with oxygen. The intermediate temperature group contains elements that form both oxygen compounds and sulfur compounds.

Jan 1, 1957

By R. G. Charles, E. A. Gulbransen, S. Barnartt

KINETICS of the reaction of zirconium with pure oxygen at elevated temperatures have been studied by several workers for periods of time up to 6 hr.1-1 In two cases,3-4 . the experimental values of oxygen uptake, w, as a function of time, t, were best fitted to the parabolic rate law w2 = kPt + constant. In others,3,4 the cubic rate law w3 = kot + constant, showed better agreement. The most recent data of Gulbransen and Andrew4 indicate that the choice between the parabolic and cubic laws for empirical representation of the data will often be arbitrary. This is particularly true if the first few minutes of the reaction with a clean zirconium surface is attributed to a different oxidation mechanism, for deviations from either rate law were found primarily during the initial period. Thus, the kinetics of this reaction have been too uncertain to permit safe extrapolation to oxidation periods of practical interest (many hundreds of hours). The data to be described are of interest, for they indicate that the cubic rate law applies over long oxidation times. The reaction of zirconium with oxygen at 1 atm pressure was followed at 350" and 450°C for 500 and 200 hr, respectively. Abraded test specimens of pure zirconium sheet' 3.0 X 2.0 X 0.012 cm in size were oxidized by the procedure previously described,3 which included periodic cooling to room temperature for weighing. The surfaces were polished to a 4/0 finish using polishing paper wet with kerosene, then wiped with petroleum ether and washed in redistilled acetone. Fig. 1 shows plots of log ? vs log t. Each curve represents the average of duplicate measurements, and deviations from the average were generally less than 3 pet. The cubic rate law (slope = 1/3) is closely followed. The rate constants, 5.2, x 10 -6 and 2.4, X 10- (mg cm-2)3 per hr at 350" and 450 oC, respectively, are plotted as log k, vs 1/T in Fig. 2, together with cubic constants calculated from the data of Gulbransen and Andrew4 for abraded specimens from the same lot of zirconium. Their data refer to runs of 6-hr duration at a pressure of 0.1 atm 0 and under conditions of uninterrupted heating. In spite of these differences, the latter data yield a straight line which appears to apply equally well to the new extended time data. The energy of activation for the oxidation process, calculated from the slope of this line, i.s 38 keal per mole. This may be compared with the value of 47 keal per mole found by Belle and Mallett3 at higher temperatures. It may be concluded tentatively that extrapolation of short-term oxidation data for zirconium to obtain the long-term behavior is best done through the cubic equation ?3 = kpt + constant. References ' E. A. Gulbransen and K. F. Andrew: AIME Trans., 1949, vol. 185, p. A.515; JouRNal OF Metals, August 1949. 'D.p. Cubicciotti Journal Amer Chemical August1949.Soc., 1950, Vol. 72, P. 3 V. Belle and M. W. Mallett: Joulnal Electro chemical Soc., 1954, ' E. A. Gulbransen 339.and K. F. Andrew: Oxidation of Zirconium Between 400" Gulbransenand 800'C.and AIME Trarzs.. 1957, vol. 209, p. 394; JOUR-Nal of Metals, April 1957. IS Barnartt, B G. Charles, and E. A. Gulbransen: Oxidation of 50 weight pet uranium-zirconium alloy, Journul Electrochemical SOC., 1957, vol. 104, p. 218.

Jan 1, 1959

By R. Simon, L. Yarborough

This paper presents a correlation for predicting the critical pressures of gas-solvent-reservoir oil systems of the type encountered in gas and solvent injection processes. Experimental data from 14 systems were used to develop the correlation which expresses critical pressure as a function of composition, C7+ mol weight, and C7+ characterization factor. Critical pressures predicted by the correlation for the 14 gas-solvent-reservoir oil systems have an average deviation of 2.8 per cent of the experimental values. The correlation war used to study a wide variety of other hydrocarbon mixtures reported in the literature whose critical conditions are in the range of interest in oil recovery work (100 to 280F and 2,000 to 6,000 psia). Critical pressures predicted by the correlation had an average deviation, expressed as per cent of experimental value, of 5 per cent for 20 miscellaneous mixtures from the literature, and 6.4 per cent for I7 methane-butane-decane mixtures reported by Sage and Lucey. INTRODUCTION Predicting critical points of hydrocarbon mixtures is an important part of phase behavior calculations. If the critical point can be predicted for a specific mixture, the separation between the bubble-point and dew-point regions will be defined, and physical properties of the mixture can be calculated by using the principle of corresponding states. Numerous correlations for predicting critical points of hydrocarbon mixtures have been published. Six of these correlationsl-8 were for light hydrocarbons, and two correlations7,8 ere for high boiling-point petroleum distillates. Organick9 And Eilerts" presented correlations which combined the published data from both light and heavy mixtures, and these correlations became the only available methods for predicting critical pressures for wide boiling range mixtures. In the course of the authors' work on secondary recovery by gas and solvent injection, experimental data were obtained for 14 mixtures of dry gas, ethane-propane-butane solvents, and various reservoir oils. The critical pressures and critical temperatures of these gas-solvent-reservoir oil systems were in the range of 1,900 to 4,800 psia and 180 to 265F. The critical pressures predicted for the 14 mixtures by the correlations of Organick and Eilerts had an average deviation from the measured values of about 13 per cent. The authors felt that it was necessary to develop a better correlation for engineering calculations and the resultant correlation, which is presented on Figs. 1 and 2, predicts the critical pressures of the 14 mixtures with an average deviation of 2.8 per cent. The validity of the correlation was tested by applying the correlation to other hydrocarbon mixtures reported in the literature. This subject is discussed later in the paper. The authors feel that there is also a need for an improved critical temperature correlation for gas-solvent-reservoir oil systems. However, developing a critical temperature correlation is a significant study in itself and is not included in this paper. EXPERIMENTAL DATA The compositions and critical points obtained by the authors for 14 gas-solvent-reservoir oil mixtures are shown on Table 1. The methane concentrations in these mixtures varied from 20 to 63 mol per cent. The intermediate hydrocarbon group, consisting of ethane, propane, and butane, varied from 20 to 64 mol per cent, and the concentration of the C,, fraction from 10 to 20 mol per cent. The physical properties of the C,, fraction covered the range from light, paraffinic, nonasphaltic (Mixtures 5, 6, 7, 8, 9 and 10) to heavy, aromatic, and asphaltic (Mixtures 13 and 14).

By C. A. Siebert, O. S. Duffendack, A. W. Herbenar

IN metallurgical problems involving the study of equilibrium in binary systems, the ,existence of an additional vapor phase, due to the presence of a volatile component in the alloy, has often been neglected. This is well indicated by the modified form of the phase rule, usually accepted in condensed systems in which pressure is not considered as a degree of freedom. In many cases the vapor pressure of the volatile component is exceedingly small and for all purposes can be considered negligible, in which case this form of the phase rule is applicable. However, alloys containing Hg, Cd, Zn, or Mg, tend to show very marked equilibrium vapor pressure, even in the solid state, and therefore present cases where the modified form of the phase rule no longer holds true. A quantitative determination of the vapor pressure of zinc in alpha brasses is not only of practical interest because of the loss of zinc in the processing of these alloys, but also of theoretical interest in that such measurements provide a means of applying the principles of theoretical physics and physical chemistry to problems of applied metallurgy. A number of investigators have reported vapor pressure measurements of zinc in alpha brasses. Hargreaves1 made extensive measurements which were used by Birchenall and Mehl² and Guttman³ for the determination of activity coefficients of zinc in alpha brasses. Hargreaves1 used a differentially heated quartz tube and measured the condensation temperature at one end corresponding to the temperature of the heated brass at the other end. Birchenall and Cheng outlined the condensation method of obtaining vapor pressure of zinc and Cd over some of their silver alloys." The primary object of the present investigation was to increase the range and accuracy of the vapor pressure data for the alpha brasses. Preparation of Alloys: Six alloys were prepared from Bunkerhill zinc and O.F.H.C. copper, both of 99.99 pct purity. The cast ingots were annealed for 24 hr at 550°C, scalped, cold rolled 40 pct and annealed for 50 hr at 550°C. The annealed bars were then surface ground and degasified for 30 min at approximately 550°C in an induction heated vacuum furnace. The surface of the bars was removed before milling the bars into relatively fine chips for chemical analysis and samples for the equilibrium cell. The analyses of the six alloys are given in table I. Experimental Method: The vapor pressure of zinc over the various alloys at a number of temperatures was determined from absorption spectra data. The spark source was produced by means of a high tension discharge between two electrodes of pure zinc. The design of the absorption vessel is shown in fig. 1. The vessel was constructed of transparent quartz which transmits the whole of the visible spectrum and the ultraviolet down to a wave length of 2000 A. The thickness of the vapor space was set at 0.8 mm so as to permit a relatively wide range of measurements without altering the vapor space, and thereby necessitating recalibration of the vessel. The furnace used for heating the absorption vessel consisted of a split wound furnace as shown in fig. 2. The spectrograph used in obtaining the transmitted zinc spectra was a double prism type especially designed for a region of 2500-3500 A. A step diaphragm used in conjunction with a tungsten filament provided the necessary intensity patterns required for calibration of the photographic plates.

Jan 1, 1951

By R. D. Satterley

THE Sherwood mine is an iron-ore mine owned and operated by the Inland Steel Co. in the Iron River district of the Menominee Range in Michigan. The property consists of an 80-acre tract in the village of Mineral Hills, about a mile north of the city of Iron River. The ore mined is a reddish brown, nonbessemer hematite and limonite. The ore bodies lie in a large syncline having an east-west strike and are associated with a rock structure that is folded in a complex manner. The two 40-acre tracts run north and south and the shaft is at about the center of the north forty. The shaft is 1286 ft. deep, with the principal operating level at a depth of 1000 ft. from surface. A new level at a depth of 1200 ft. is in process of development. The ore body at the 1000 ft. level is east and west at approximately the line between the north and south forties and at this elevation is from 50 to 250 ft. wide and extends above the level at varying heights of from 50 to 250 feet. The 1000-ft. haulage drift extends south from the shaft, through the east-west ore body to the slates on the south side of the body. The ore body was intercepted in the drifting at about 800 ft. from the shaft and was about 200 ft. wide at that point. A crosscut was extended to the east and west property lines along the south boundary of the ore body. This east-west ore body is laid out in areas 80 ft. wide for stoping with pillars 40 ft. wide. With this plan a stope is approximately 80 by 200 ft. and has a pillar on both sides that is approximately 40 by 200 ft. The ore has a height of from 50 to 250 ft. above the elevation of the level, therefore the height of the stopes varies in accordance with the height of the ore body at each location. From the crosscut, two main raises, each 6 by 7 ft., are put up into each 80 ft. stope area (Fig. I). One of the main raises serves as a manway and the other as an ore raise, through which the ore is transferred from the stope to the tramming equipment. The original layout was for scraping of the ore from under the stopes into the ore raises. The ore raise is put halfway (east and west) along the 80-ft. stope area and usually is in iron formation. The manway and ore raise are on approximately 15-ft- centers. These main raises are put up to a height of from 22 to 30 ft. above the level floor, then from the top of the ore raise a scraper drift (8 X 8 ft.) is driven across the width of the ore body, which is in the neighborhood of 200 ft. From the scraper drift, mill raises are put up at 12 ½ -ft. centers, staggered on opposite sides of the drift, and these are extended 23 ft. above the elevation of the scraper-drift floor. The sublevel connecting the top of these mill raises is called a mill "sub." Other sublevels are developed parallel to the scraper and mill subs at 25-ft. vertical intervals above the mill sub. The mill sub and the other subs above the mill sub are known as sublevels or dog drifts, and are 4 ft. wide and 6 ft. high. These dog drifts

Jan 1, 1945

By Sam N. Dewitt, Albert S. Trube

This paper presents a discussion of the pressure maintenance operations which were begun in the New Hope Field. Franklin County. Texas. in 1944. The project has required the injection of extraneous waters at depths from 7.300 to 8.000 ft with intake well-head pressures up to 4.000 psi in three different reservoirs — the Bacon. Hill. and Pittsburg. Records of oil and water production. water injection and the GOR have been kept for each reservoir and reservoir pressures were taken at regular intervals. These data indicate that the Bacon Reservoir had no apparent water encroachment up to the time of water injection. However. the Pittsburg and Hill reservoirs had some natural water influx hut not sufficient to prevent pressures from declining below the bubble point. The Bacon and Hill reservoirs responded almost immediately to water injection. while the Pittsburg which is the least permeable. has shown good pressure response only since .August, 1948. The principle objective of the project has been to increase ultimate recovery. Success of the project to date also has resulted in reduced lifting costs. Esti- mates based on the initial water breakthrough patterns indicate that the primary objective of substantial additional recovery will he accomplished, and there is a possibility that the original estimates elf oil recovery with pres-sure maintenance will he exceeded. INTRODUCTION This pressure maintenance project was one of the earliest primary pressure maintenance programs to he attempted on a multiple zone field. There are three producing reservoirs into which water is being injected for the purpose of maintaining pressure and increasing the ultimate recovery- from each. This paper is limited in scope to al1 account of the development of the project. the pressure production relationship prior to the injection of water and the effect of water injection on the producing reservoirs. Also discussed are the nature of the injection system and the indicated results on initial water break-through in the Bacon Reservoir. FIELD CONDITIONS The New Hope Field, which is located about 12 miles northeast of Winusboro, Franklin County, Texas, is an elongated symmetrical anticline containing four known oil reservoirs. The reservoirs are of the Trinity group of the Comanchean or Lower Cretaceous period and are found in Table I. The oil productive portion of each reservoir is not present in all of the producing wells because their areas and positions vary with respect to one another. Fig. 1 shows the relative position of the four reservoirs and illusIrate? how some wells could penetrate all four, while others are restricted to three. two. or perhaps one. depending on structural location. The first three reservoirs contain undersaturated oil. The deepest. the Elledge, has a primary gas cap. Although this reservoir covers a considerable area of the field. it has a very thin section and a low order of permeability. Elledge producing wells have generally been characterized by an early increase in GOR, making it necessary to recomplete them in other reservoirs. (At present. one well is completed in the Elledge. which is still producing.) Because of the difficulties en-countered in producing oil from this reservoir. and the small quantity of oil actually present. future attempts at producing it will probably be on a salvage basis during the later life of the program. For this reason, the remainder of this report will be confined to a discussion of the Bacon, Hill and pius-burg reservoirs.

Jan 1, 1950

By S. C. Sircar, D. R. Wiles

The rate has been studied of the hydrogen reduction of nickel ions in acetate -buffered solutions, using a nickel catalyst. At temperatures between 130°and 160°C, the rate is found to be proportional to the catalyst area, the nickel ion concentration, and the hydrogen pressure. The effect of hydrogen ions is to reduce the observed rate, likely by causing the reverse reaction (dissolution) to proceed. The experimental activation energy was found to be 25 kcal per mole. THE precipitation of metals and lower oxides from solution by hydrogen reduction has been quite actively investigated during the past few years.1 In the case of nickel, the kinetics of the precipitation have been studied in ammonia solution2 but extension of this study to acid solutions has not attracted much interest, largely because of the unfavorable thermodynamics at all but the lowest acidities. For example, Schaufelberger foundg that only 10 pct reduction of nickel could be effected in sulphate solutions. One kinetic study of the reduction of Ni++ has been reported by Knacke, Pawlek, and Sussmuth,4 in which the order of the reaction was found to be one in nickel ion and one-half in hydrogen pressure. No mention was made as to the part played by the nickel catalyst, or by the pH of the solution. Moreover, the activation energy reported (4 .12 kcal per mole) is so low as to lead to some question as to whether diffusion might be playing a major role in determining the kinetics. We have recently completed a study5 of the kinetics of the hydrogen precipitation of nickel from acetate-buffered acidic solutions whose results confirm and amplify those of Knacke et al. EXPERIMENTAL PROCEDURES The work was done in a high-pressure autoclavee by the usual technique of removing small samples of the solution for analysis. Nickel analysis was done colorimetrically by the dimethylglyoxime method.' The catalyst used was carbonyl nickel powder (Standard A powder of the Mond Nickel Co., Ltd.) which was found to be composed of spheres of less than 350 mesh. The surface area of the powder was determined in this laboratory by the B. E. T. method to be 1.85 sq m (m2) per g. The catalyst was added to the solution only after the proper temperature and pressure had been reached. Agitation of the baffled system was by a turbine-type impeller, rotated at speeds between 400 and 750 rpm. The reduction rate was found to be independent of the stirring rate, so it was assumed that diffusion in the liquid does not limit the rate. In typical experiments, the nickel concentration was unchanged during an induction period of variable length. The concentration then decreased sharply, and gradually levelled off to approach the final equilibrium value. In some cases, notably at high stirring rates, the nickel concentration was found to increase considerably during the induction period, and then to decrease. In all cases, the rate was determined from the slope of the tangent to the rate curve as the concentration first decreased below the initial value. This is seen in Fig. 1. The rate measurements were found to be reproducible to within about 5 and to be quite independent of the nature or duration of the induction period. The range of conditions used is given in Table I.

Jan 1, 1961

By H. F. Mills

THE Iron King mine is 12 miles east of Prescott Arizona, in low foothills of the Agua Fria mining district. It was operated in 1906 and 1907, using gravity methods of concentration, mostly on oxide ores. In 1923 and 1924 shipments of sulphide ores were made to the Humboldt smelter. It remained inactive and stripped until 1936, when it was unwatered and sampled to the 400-ft level, the bottom at that time. In 1937 the Iron King Mining Co. purchased the mine and shipped oxide ores. During 1938 a bulk flotation plant of 140 tons daily capacity was erected. The mill has been enlarged and operations have been continuous since the mill first started. In July 1942, the Shattuck Denn Mining Corporation purchased the physical assets from the Iron King Mining Co., and since that time it has operated as the Iron King Branch of the Shattuck Denn Mining Corporation. Economic metals recovered are gold, zinc, silver, lead, a little copper, and fluxing pyrite. The ore occurs as a series of northward-dipping shoots arranged in echelon pattern, the series extending over a length of 3500 ft. Strike lengths of shoots vary from 60 to 600 ft, and widths from 3 ft to as much as 14 ft. The ore occurs in a sheared zone in pre-Cambrian chloritic schist. This schist belt is about 6 miles wide, and the ore zone is about 4 miles from the pre-Cambrian granites to the west. No intrusive rocks have been found in the mine, nor is there evidence of any on surface that might indicate a genetic connection with the ore occurrence (Fig I). The schists strike N23°E and dip 75° to the northwest, which might indicate an overturned thrusting from the granites. In the upper levels, the echelon pattern in which the ore occurs was quite regular, no disturbance of the enclosing schist, or of any faulting that might contribute to the formation of the ore pattern was noted. There is a possibility that the ore zone may be on the axis of an isoclinal fold. Another interesting feature is the more or less typical zoning of minerals along the strike in each of the ore shoots (Fig 2). The north end of each shoot is enclosed by schist, while the south ends usually extend out at full width beyond the economic mining limits in a pyrite-quartz low-grade material. The plane of demarcation between ore and schist is very sharp, with little or no impregnation of sulphide in the schist, especially on the footwall side. The footwall schists are usually firm and strong, and vary from dioritic phases to fine-grained, lighter colored bands, almost silky in texture. The hanging wall for a width of 50 to 8o ft consists of alternating sheetings of chloritic and pyritic schists. The mine is now partly developed to the 92o-ft level, with some diamond drilling from the 1150-ft station of No. 6 shaft. Economically there has been little change in nature or grade of ore from the top of the sulphides, about 200 ft below surface, to the bottom levels. There have been a few echelons in depth, just as there are in plan, and while a few shoots have had

Jan 1, 1947

By F. Brons, W. C. Miller

Pressure information for use in material-balance calculations is obtained, where possible, from pressure build-up surveys in shut-in wells. Using proper extrapolation methods, static pressures are obtained which, by averaging, give the field static pressure. Often, particularly in fields with a large number of wells, only spot pressure readings are available. A graphical method is presented here which enables the determination of the corrections which must be applied to the spot readings to give an estinzate of the static pressure. Although the static pressures thus obtained are not so reliable as those from build-up surveys, they are more nearly correct than the spot readings themselves for use in material-balance calculations. INTRODUCTION The average static pressure in a bounded reservoir is determined from a number of individual-well pressure measurements. Where pressure build-up curves are available, extrapolation methods such as described in Ref. 3 may be used to determine the static pressure in the drainage area of each individual well. The possibility of using pressure build-up curves presupposes that each well being surveyed is closed in during a certain period and that, during this time, a pressure recorder is left suspended in the hole. For surveys in fields with a large number of wells, this is usually not feasible for economic and other reasons. Either a large number of pressure recorders would have to be used simultaneously or, using a limited number of recorders, the time interval needed to complete a field-wide survey would be too long. The data obtained for this incomplete coverage are insufficient to permit reliable averaging of the few calculated static pressures over the entire reservoir. In many such cases another type of pressure information is available, i.e., spot pressure readings. During this type of pressure survey all wells are closed-in simultaneously and, after a reasonable shut-in time (e.g., three days), pressure readings are taken by running the recorder in and out of each successive well. These surveys, which are less expensive, are often taken at regular intervals, say once or twice a year. In fact, such surveys are required by the state regulatory bodies in many portions of the united States. These spot readings are normally lower than the static (fully built-up) pressure due to the relatively short shut-in time. No direct means of extrapolating such a reading to the static pressure is available because no pressure build-up record is obtainable. Consequently, these data are inferior to pressure build-up information as a basis for estimating the stabilized reservoir pressure in the drainage area of a specific well. For the common case where abundant spot readings but only a few pressure build-up surveys are available, our studies suggest that it may be possible to design a program which will combine the two types of information and provide an estimate of the average reservoir pressure that is more reliable than that obtainable solely from either set of data. in time) gives a point marked p. The actual static pressure at the time the well was shut-in is marked by p.. The illustration shows that, even if a build-up curve is available and can be extrapolated, a correction

By Wei-Kao Lu

A general rate equation is derived for gas -solid reactions in metallurgical processes by considering the contributions of chemical reaction at inter-phase boundaries and diffusion through the solid product layer simultaneously. This equation takes care of the whole range continuously from purely diffusion control to purely chemical reaction control. The parabolic law,' McKewan's equationa derived with the assumption of interface area control and the equation derived by Kawasaki et al. with the assumption of purely diffusion control are found as the limiting cases of the corresponding forms of the general rate equation. Many metallurgical processes involving gas-solid reactions have been extensively studied. The common examples of these processes include the reduction of oxides to metallic products, the roasting of sulfides to oxides or chlorides and the oxidation of metals. Gas-solid reactions consist of at least two kinds of steps; one involves the transport of reactant and product to and from the reaction zone and the other is the chemical reaction taking place at the interphase boundaries. In the limiting cases one or the other of the above mentioned steps will be much slower than the other and is then rate controlling. For example, the oxidation of metals is diffusion controlled and obeys the parabolic law.' On the other hand, if the diffusion rate is much larger than the chemical reaction rate then it will be controlled by the chemical reaction rate. This latter case occurs for the reduction of iron oxides studied by McKewan. If the rate of diffusion and of the chemical reaction have the same order of magnitude, a more detailed analysis is necessary. Thus at the beginning of the reaction when the solid and gaseous reactants are in direct contact, the reaction should be chemical reaction rate controlled as no diffusion process is involved. At the other extreme as the reaction zone moves further into the solid, the diffusion distance becomes greater and the diffusion rate continuously decreases. Eventually, therefore, for a sufficiently large sample the rate must become diffusion controlled. As the transition from one controlling step to the other must be continuous, we cannot describe this transition period by either of the two limiting cases. In this paper the author attempts to derive a general rate equation for gas-solid reaction systems. This is effected by considering the rates of diffusion and chemical reaction simultaneously from the state of pure diffusion control to pure chemical reaction control. I) DERIVATION The system under consideration is made of at least three phases, namely the gaseous one, the solid reactant, and the solid product as shown in Fig. 1. The notations are listed at the end of the paper. The mass transfer process involves the diffusion of reactants and products across the solid product layer. It is reasonable to consider that no chemical reaction will take place in the solid product layer with respect to both gaseous reactant and product. For the characteristics of local equilibrium of the system, the diffusion process is really in a quasi-steady-state. It will be proved in the following paragraphs. Then we can invoke the law of conservation of mass valid for all chemical species passing through the layer. The solid reactant sphere has an initial radius, ro, after a fraction of completeness of the reaction, the unreacted core has a radius ri, where r, is in the solid product region. Let Cg be the activity of gaseous reactant in the

Jan 1, 1963

By F. von Gemmingen, E. J. Fasiska, L. Zwell

EARLIER studies of the dependence of creep on structure1 and of the dependence of creep rupture on creep behavior2 did not include detailed discussion of the phases present in the specimens under examination. It is of interest to determine the nature and amounts of such phases present since it is well known that these are dependent on composition, heat treatment and creep conditions.3 This investigation has therefore been undertaken to identify these constituents and to determine their relative amounts. This report presents the results of this investigation and describes an improved "extraction replica" technique developed in the course of the work. The composition of the Type 316 austenitic stainless steels studied in this investigation is given in Table I. The specimens were solution treated at 2000°F for 1/2 hr and water quenched. Those specimens subjected to prestrain at room temperature Methods for extracting precipitate particles from materials for electron and X-ray diffraction analysis have been described by Fisher,4 Smith and Nutting: and Booker and coworkers.6'7 Electrolytic extraction methods have been described by Andrews and Hughes.8 The first two methods have been used at this Laboratory, but have not proved satisfactory for many problems requiring X-ray diffraction analysis. It has been difficult to remove the replicas or to avoid tearing them during removal. These difficulties are overcome by backing the replica with a water-soluble plastic such as Dupont 51-05 Elvanol (polyvinyl alcohol). The backing increases the thickness of the replica so that it can be mechanically stripped from unloosened particles without folding or tearing. This procedure eliminates the stripping of wet replicas, which usually have a low tear strength. By stripping replicas after drying, it is possible to extract partially loosened particles which otherwise would remain imbedded in the metal. The modified method is as follows: after the specimen is polished, it is etched for 60 min in modified glyceregia consisting of 30 ml glycerol, 7 ml nitric acid, and 4 ml of hydrochloric acid. The sample is then washed, air dried, and coated with a 20 pct Baker and Adamson 1611 collodion (85 pct amyl acetate by volume) film. After the collodion film is dry (about 15 min), the sample is again etched in the modified glyceregia for 50 min, washed with isopropyl alcohol (to prevent dissolving the collodion) and air dried. A very thick coat of polyvinyl alcohol (about 50 pct solution "Elvanol Dupont 51-05" in water) is poured over the sample and is permitted to dry for about 24 hr. The composite film containing the precipitates is then stripped from the specimen and floated, polyvinyl alcohol side down, in water (at about 50°C) until the polyvinyl alcohol dissolves. This usually takes about 15 min. Should any of the polyvinyl alcohol remain on the replica, it does not give a crystalline diffraction pattern and therefore does not hinder identification of the precipitates. The extraction replica, floating in water, is picked up on a glass fiber and mounted in the Debye-Scherrer camera for X-ray diffraction analysis. Concentration of the etchant, and also etching time, had to be increased for several of the samples. Fig. 1 shows two extraction replicas taken from different areas of spec. M74-37; X-ray analysis showed a strong diffraction pattern of M23C6 and a medium one of u phase. A

Jan 1, 1962

By A. A. Bauer, H. A. Saller, F. A. Rough, J. R. Doig

among uranium alloy systems are the U-Zr, U-Ti,and U-Mo binary systems, in that an intermediate phase, of limited solubility range, exists in each system. These intermediate phase alloys offer a promising field of investigation, both as binary alloys and as ternary alloy combinations. While a limited amount of work has been done on the binary alloys, none has been done on ternary combinations of these alloys. As a possible prelude to more intensive investigation of these systems, a study of the phase relationships between the 6 phases of the U-Zr and U-Ti systems was undertaken. The solid-state portions of the binary constitutional diagrams for the U-Ti,1 Zr-Ti,2 and U-Zr3 systems are shown in Fig. 1. The solid to liquid transformations are not shown, as these transformations were not studied in the ternary system. The phase designations employed are based upon those shown in the uranium constitutional diagrams. The crystal structures of the various phases are given in Table I. Experimental Materials and Methods The ternary section presented is based upon the results of thermal, metallographic, and X-ray analyses of a series of alloys ranging in composition between the phases of the U-Zr and U-Ti systems (U-74 atomic pct Zr to U-35 atomic pct Ti). After preparation of the alloys, thermal data were obtained. On the basis of these data, specimens were heat treated and examined metallographically. Specimens were then selected from those heat treated for X-ray determination of the phases present in what were considered critical phase regions. Alloy and Specimen Preparation—Alloys for this investigation were prepared from selected as-reduced uranium and crystal-bar zirconium and titanium. For nominal compositions, see Table 11. Charges were arc melted from five to seven times under a helium atmosphere, finally being cast into wire-bar form for fabrication. A zirconium getter button was used to clean the furnace atmosphere prior to melting. The alloys were homogenized 20 hr at 900 °C and furnace cooled. A portion of each bar was then removed for thermal analysis; the remainder was saved for fabrication. Alloys 8 through 14 were placed in steel tubes along with zirconium getter chips and, after flushing with argon, the tubes were welded shut and rolled at 1500 °F to a 50 pct reduction in diam. The remaining alloys were annealed 24 hr at ll00°F to insure transformation of the ? phase to the 8-U2Ti phase and were then hot rolled from a salt bath. Attempts to roll alloys 6 and 7 at 1100 °F were unsuccessful. Following this, attempts were made to roll pieces of alloys 1 through 5, which had cracked rather severely during casting, at 1200 °F, but these efforts were also unsuccessful. These alloys were, therefore, further treated in their cast and homogenized condition. All alloys were pickled to remove oxide formed during rolling. Thermal data were obtained on these alloys by conventional differential thermal analysis at a heating rate of 30C per min, and by a high-speed heating method at rates of approximately 10°C per sec. For the latter method of analysis, a 36-gage Chromel-Alumel thermocouple is spot welded between two slivers of alloy, the sandwich being en-

Jan 1, 1958

By O. J. Neslage, R. W. Jenkins

MINE operators today are paying increased attention to the mechanization of drilling operations as an important factor in increasing efficiency and decreasing costs. Recent progress in the design of drill jibs for mounting on drill carriages, or jumbos, has done much to advance the mechanization of mining methods. This progress has introduced new opportunities in the application of "jib jumbos" that are worth serious consideration. An attempt will be made here to classify the various types of jumbos and drill mountings available for level development and flat stope work, t6 indicate applications, and to measure their effectiveness in relation to their cost. The data here are based on a wide variety of field usage, and are offered only to point up, in a general way, the relative efficiency in proportion to cost. It should be remembered that any contemplated jumbo installation must be studied to determine what type of installation is most suitable, considering ground conditions, loading, timbering and haulage equipment, service available, and attitude of manpower. Early Drill Carriages: The advantages of some sort of a drill carriage were recognized at the time rock drills were introduced. In drift or heading operations where a fairly standard drill round and cross section were anticipated, as well as in flat bedded deposits where standard slabbing rounds were used, track and crawler-mounted drills found an early application. These first drill jumbos were little more than drill carriers, designed locally and manufactured with materials at hand. Of comparatively simple construction, function, and low capital cost, they usually consisted of a hinged column which supported one or more drills on arms or universal bars. When the column was pivoted vertically, the drills were moved into position. Screw jack extensions reached from the column to the roof and floor to hold the drill rigid. In some cases, particularly in tunnel jumbos, enough weight was carried that rail clamps or roof jacks were sufficient. Many of these column and arm-type jumbos, usually equipped with air and water manifolds, steel racks, and staging for drillers, are still in use today. Some have employed air or hydraulic extensions for securing the columns. They offer the equip-saving advantage of having all the necessary out, ment together, and they un be moved i and t. set up and torn down as a unit. Boom-type Jumbos: When the advantages of to column-type jumbo were seen, operators could to realize the further gains possible. More time could be saved with mechanical assistance to position api drill vertically. A rack on the column and a pinion on the arm for raising and lowering the drill in the manner of a quarry bar were tried with some success. The most outstanding solution to the vertical handling problem was reached with the boom-type of jumbo. Here two or more machines were mounted on a cross arm at the end of a boom that was pivoted at the rear of the track. This was raised and lowered by various mechanical aids. Occasionally air or hydraulic power was used. Nearly all of today's wagon drills use this boom-type principle. Boom jumbos represent a savings in time and physical effort expended in raising and lowering the drills. The boom must be balanced by the roof of the truck which is secured by rail clamps or type jacks. The most successful application of areawhere this of jumbo has been in the Tri-State area where multiple long-feed machines are used on caterpillar-mounted, boom-type jumbos for slabbing

Jan 1, 1951

By Edward B. Walker, Michel Grosmangin

The geological and economic conditions peculiar to the Greater Oficina area are presented to demonstrate the necessity of a low-cost, well-site method of distinguishing gas-bearing formations. The method of gas detection with the neutron log is briefly discussed and its limitations are explained. A new method is described which consists in running a second neutron log with a larger source-to-detector spacing. Field data indicate that under favorable conditions the larger spacing response is proportionately more influenced by the virgin gas zone than is the shorter spacing response. One important condition is that the gas sands be invaded, with a diameter of invasion equal to about two to three times the hole diameter. The calibration of the longer spacing log is made so that the two logs read the same deflection in shale and in a known water or oil sand. Under such conditions, gas is indicated by a positive separation, i.e., the curve for the longer device is displaced to the right of the curve for the shorter device. Because of the non-linearity of the long spacing response, low porosity formations also show positive separations. In sands with large porosity variations, the gas sands can no longer he located visually. They can be detected on a plot of shorter spacing vs longer spac-ing deflections. INTRODUCTION In the Greater Oficina area of Eastern Venezuela, the rapid and accurate detection of gas from well logs is of primary importance because of a combination of economic, geologic, and operational conditions. Briefly, these conditions are: economic—there is no market for gas at the present time; geologic—a single well may contain as many as 30 or more oil or gas sands for which intervals -to be tested must be selected; opera-tional—first, once opened to the casing through perforations, gas sands are extremely difficult and expensive to squeeze off, and second, gas detection must be rapid because the geologist must decide immediately, at the well, which sand to perforate. During the early period of exploitation in Greater Ofi-cina, when clay base muds were used, sidewall samples, together with electric logs, gave fairly good distinction between oil and gas sands. When exploitation became concentrated on deep fields of poorer sidewall sample recovery, and after the advent of oil emulsion muds, now the standard drilling fluid in Greater Oficina, the regular neutron log became the most reliable indicator of gas. In 1953, R. Norelius devised the dual-spacing neutron technique for gas detection. The dual-spacing neutron log has proved to be highly successful in detecting gas and has been adopted as a regular survey by all of the oil companies of the area. Several hundred dual-spacing neutron logs have been run in Eastern Venezuela and several tests per well are available for positive evaluation of the logs. The findings outlined below are based upon this extensive field experience. GEOLOGICAL CONDITIONS OF THE GREATER OFICINA AREA The Greater Oficina area lies on the south flank of the Eastern Venezuela Basin (Fig. 1). Nearly all accumulations of oil and gas in the area are trapped, in whole or in part, against normal faults. All known oil and gas reservoirs in Greater Oficina occur in the Ofi-cina formation (Miocene-Oligocene) or in the "U" sands. The U sands are the lithologic equivalent of the Merecure group (Otigocene-Eocene), which contains oil in many fields north of Greater Oficina. Most of the petroleum produced in Eastern Venezuela is from the Oficina formation.

Jan 1, 1958

By Kefton H. Teague

Olivine is a mineral containing a mixture of forsterite (Mg2SiO4) and fayalite (Fe2SiO4) in solid solution. The name olivine was first applied by Werner in 1790 (Hunter, 1941) because of the olive-green color of the mineral. Olivine is the principal component of the rock dunite, which itself is a member of the peridotite group of ultrabasic igneous rocks. European uses of the terms olivine and dunite are somewhat different than US usage. In commerce European usage defines dunite as containing 36 to 42% MgO, 36 to 39% SiO2, and loss on ignition of approximately 10%. The term olivine is used to designate a material containing approximately 85% forsterite, with a chemical composition of approximately 45 to 50% MgO, 40 to 43% Si02, 5 to 8% Fe2O3, and ignition loss of 1 to 2%. Uses The principal use of olivine is in various applications involving hot metal. Table I shows the best estimate available as to the amount of olivine consumed by various industries worldwide. In excess of 90% of world uses involve hot metal, with approximately 75% as a slag conditioner in the blast furnace production of pig iron. Approximately 15% of total olivine usage is as a special foundry sand in mold making for the brass, aluminum, magnesium, and manganese steel foundries (Schaller, 1957, 1958; Snyder, 1957; Anon., 1977). Olivine was first used as an industrial mineral in the early 1930s for a refractory material (Anon., 1970; Hunter, 1941). As a refractory raw material, olivine was first introduced in the United States as hand-cobbed, selected, shaped blocks of crude olivine. This use met with limited success. More recently, finely ground olivine blended with MgO and pressed into bricks, which are then fired, has found use in glass tank furnaces and open-hearth furnaces. Ramming or gunning mixes for basic furnace linings also utilize olivine. Olivine has been used in ladle linings with varied success. In Europe, substantial tonnages of olivine are utilized in refractory brick for night storage heaters (Anon., 1970). A limited amount of olivine has been used in the past as a fertilizer (magnesium source) and has been fused with rock phosphate to produce a magnesium phosphate as a plant food. The relatively high magnesia (MgO) content of olivine also attracted attention to it as a potential source of both magnesium compounds and as a source of metallic magnesium (Bengston, 1956; Hunter, 1941). The use of olivine as an additive in the blast furnace is relatively new, having been developed during the last decade. J.W. Currier (Private communication, 1978) describes the behavior of olivine in the blast furnace as follows: Olivine (Mg, Fe2, Si04) represents a unique lime-free source of magnesia and silica as a blast furnace charge component. Only recently has the magnesia-rich mineral been recognized as beneficial cleaner for blast furnace experiencing the problems associated with excessive alkali inputs and/or low coke stabilities. For some time it has been known that alkalis tend to recycle and accumulate in blast furnaces. In the high temperature region of volatilization the elemental alkalis formed attack the integrity of the graphite structure. This alkali attachment is enhanced when poor coke is used. Higher in the furnace stack volatile alkali cyanides condense and oxidize. This accumulation of alkalis tends to agglomerate the burden materials, producing scabs and scaffolds. These structures not only inhibit the downward movement of burden materials and the upward passage of wind, but also lead to erratic furnace performance

Jan 1, 1983

By R. W. Jenkins, O. J. Neslage

MINE operators today are paying increased attention to the mechanization of drilling operations as an important factor in increasing efficiency and decreasing costs. Recent progress in the design of drill jibs for mounting on drill carriages, or jumbos, has done much to advance the mechanization of mining methods. This progress has introduced new opportunities in the application of "jib jumbos" that are worth serious consideration. An attempt will be made here to classify the various types of jumbos and drill mountings available for level development and flat stope work, t6 indicate applications, and to measure their effectiveness in relation to their cost. The data here are based on a wide variety of field usage, and are offered only to point up, in a general way, the relative efficiency in proportion to cost. It should be remembered that any contemplated jumbo installation must be studied to determine what type of installation is most suitable, considering ground conditions, loading, timbering and haulage equipment, service available, and attitude of manpower. Early Drill Carriages: The advantages of some sort of a drill carriage were recognized at the time rock drills were introduced. In drift or heading operations where a fairly standard drill round and cross section were anticipated, as well as in flat bedded deposits where standard slabbing rounds were used, track and crawler-mounted drills found an early application. These first drill jumbos were little more than drill carriers, designed locally and manufactured with materials at hand. Of comparatively simple construction, function, and low capital cost, they usually consisted of a hinged column which supported one or more drills on arms or universal bars. When the column was pivoted vertically, the drills were moved into position. Screw jack extensions reached from the column to the roof and floor to hold the drill rigid. In some cases, particularly in tunnel jumbos, enough weight was carried that rail clamps or roof jacks were sufficient. Many of these column and arm-type jumbos, usually equipped with air and water manifolds, steel racks, and staging for drillers, are still in use today. Some have employed air or hydraulic extensions for securing the columns. They offer the equip-saving advantage of having all the necessary out, ment together, and they un be moved i and t. set up and torn down as a unit. Boom-type Jumbos: When the advantages of to column-type jumbo were seen, operators could to realize the further gains possible. More time could be saved with mechanical assistance to position api drill vertically. A rack on the column and a pinion on the arm for raising and lowering the drill in the manner of a quarry bar were tried with some success. The most outstanding solution to the vertical handling problem was reached with the boom-type of jumbo. Here two or more machines were mounted on a cross arm at the end of a boom that was pivoted at the rear of the track. This was raised and lowered by various mechanical aids. Occasionally air or hydraulic power was used. Nearly all of today's wagon drills use this boom-type principle. Boom jumbos represent a savings in time and physical effort expended in raising and lowering the drills. The boom must be balanced by the roof of the truck which is secured by rail clamps or type jacks. The most successful application of areawhere this of jumbo has been in the Tri-State area where multiple long-feed machines are used on caterpillar-mounted, boom-type jumbos for slabbing

Jan 1, 1951