Search Documents

By J. R. Thoenen, M. C. Malamphy, G. K. Dale

The beginning of the war and the events leading up to it precipitated a near crisis in the aluminum industry. Demands for the metal reached proportions far beyond the prewar production capacities and, in addition, the submarine menace seriously curtailed the importation of bauxite from South America, hitherto a chief source of high-grade ore. The situation required an intensive search for domestic ore to augment the reserves and in October 1941 Congress directed the Department of the Interior to investigate the extent, mode of occurrence, and quality of bauxite in the United States. In December of that year the Bureau of Mines and the Geological Survey began the search for bauxite in Arkansas, where more than go per cent of the domestic ore had been produced and where the greatest amount of bauxite was known to occur. The program involves the geophysical and geological investigation of the Arkansas bauxite region and the core drilling of areas considered favorable for the occurrence of bauxite deposits. Cores taken from the bauxite-kaolin zone are sampled and analyzed in the Bureau of Mines laboratory in Little Rock. The information from each of the deposits discovered is then assembled, the bauxite is graded with respect to its possible utility, tonnage estimates are made, and the whole is presented in the form of a war minerals report. Thirty-eight new bauxite deposits had been discovered and investigated at the end of the calendar year 1944, and the presence of several others had been indicated by the drilling. More than 5000 holes had been drilled throughout the bauxite region, and more than 60,000 chemical analyses had been made of samples taken from the bauxite-kaolin zone. A study of the chemical analyses led to certain general conclusions not only with regard to the chemical composition of Arkansas bauxite, but also with regard to its component minerals. Charts and diagrams based on these conclusions have been developed for practical use by the Bureau of Mines: (I) to serve as a check against laboratory analyses, (2) to present tonnage estimates of ore bodies based on mineral composition, (3) to illustrate the relationship of tonnages of bauxite to the alumina, silica, and iron content, and (4) to serve as a control for mining operations by providing a means for quick estimates of the value of the ore from a partial analysis of its chemical constituents. The use of charts and diagrams similar to those discussed in this paper-- is not new. The use of the trilinear diagram for studying the ultimate analyses of coals as of proposed by Ralston in Bureau of Mines Technical Paper 93 (1915) showed that the various ranks of coal fell in different areas on the diagram and that volatile matter, calorific value and other properties could also be plotted by the use of contours. A considerable subsequent literature, largely on classification of coals, has accurnulated since then, showing the utility

Jan 1, 1948

By J. R. Thoenen, M. C. Malamphy, G. K. Dale

The beginning of the war and the events leading up to it precipitated a near crisis in the aluminum industry. Demands for the metal reached proportions far beyond the prewar production capacities and, in addition, the submarine menace seriously curtailed the importation of bauxite from South America, hitherto a chief source of high-grade ore. The situation required an intensive search for domestic ore to augment the reserves and in October 1941 Congress directed the Department of the Interior to investigate the extent, mode of occurrence, and quality of bauxite in the United States. In December of that year the Bureau of Mines and the Geological Survey began the search for bauxite in Arkansas, where more than go per cent of the domestic ore had been produced and where the greatest amount of bauxite was known to occur. The program involves the geophysical and geological investigation of the Arkansas bauxite region and the core drilling of areas considered favorable for the occurrence of bauxite deposits. Cores taken from the bauxite-kaolin zone are sampled and analyzed in the Bureau of Mines laboratory in Little Rock. The information from each of the deposits discovered is then assembled, the bauxite is graded with respect to its possible utility, tonnage estimates are made, and the whole is presented in the form of a war minerals report. Thirty-eight new bauxite deposits had been discovered and investigated at the end of the calendar year 1944, and the presence of several others had been indicated by the drilling. More than 5000 holes had been drilled throughout the bauxite region, and more than 60,000 chemical analyses had been made of samples taken from the bauxite-kaolin zone. A study of the chemical analyses led to certain general conclusions not only with regard to the chemical composition of Arkansas bauxite, but also with regard to its component minerals. Charts and diagrams based on these conclusions have been developed for practical use by the Bureau of Mines: (I) to serve as a check against laboratory analyses, (2) to present tonnage estimates of ore bodies based on mineral composition, (3) to illustrate the relationship of tonnages of bauxite to the alumina, silica, and iron content, and (4) to serve as a control for mining operations by providing a means for quick estimates of the value of the ore from a partial analysis of its chemical constituents. The use of charts and diagrams similar to those discussed in this paper-- is not new. The use of the trilinear diagram for studying the ultimate analyses of coals as of proposed by Ralston in Bureau of Mines Technical Paper 93 (1915) showed that the various ranks of coal fell in different areas on the diagram and that volatile matter, calorific value and other properties could also be plotted by the use of contours. A considerable subsequent literature, largely on classification of coals, has accurnulated since then, showing the utility

Jan 1, 1948

By Frank H. Kingdon

and eventually we would have trouble. That is, these little localized overstresses may not be important if the structure is loaded a few times, but may be important if the structure is loaded many thousands of times. The existence of localized stress has been demonstrated by direct experimentation with delicate extensometers by the elaborate investigations of Coker. Localized stresses four, five, and six times those that we would get by the ordinary laws of mechanics exist in most of our structures. These stresses, ordinarily, under steady load do no damage but if they are repeated many times may start progressive failure. So far, we have seen no failure that could not be explained by localized high stress at a nick, a crack, a point where one heat treatment stopped and another began, or where there was local faulting, or any one of a dozen causes. In the case of drill rods, the actual distribution of stress must be different from that which any mathematical analysis could predict. It would seem that the spread of damage from the localized overstresses, so far as we can see now, explains the phenomenon known as fatigue. The Ideal Drill Steel By Frank H. Kingdon The essential qualities of a drill steel are: (I), It must be easily forged; (2), the forged bit end must permit easy heat treatment to obtain hardness to resist chipping; (3)) the bar or body must be stiff to resist bending or twisting and yet tough to resist shock and vibration, with resulting breakage, (4), the forged shank end must be easily heat treated to obtain hardness with great toughness. Minor requirements are that the bit and the shank are in alignment with the body; that the shank is of the proper shape and length and the shank collar or lugs of the proper diameter and length; that the hole is free from obstruction; that the striking end of the shank is flat and square; that the bit is of the proper shape, with the cutting and reaming edges formed full and to the required size; that the reaming edges are concentric with the axis of the steel, and that there are no sharp corners at the shoulder where the bit blends into the body. The essential qualities of a bit, are: That its shape be such that maximum cutting speed can be maintained for as great a distance as possible before wear of the gage and cutting edge reduces the speed of penetration to a point where a change of steel is made necessary; that the size or diameter of the drill hole corresponding to the gage of the bit can be maintained with the least possible reduction as the depth of the hole increases, and that the bit can be correctly and readily formed and heat treated. The following features of bit design require attention: Shape,

Jan 1, 1922

By H. W. Schreiber, G. R. Castle

INTRODUCTION The small mining company faces the dilemma of how to finance the development of its properties. Many of these small companies don't have the financial resources to pay for development costs from their own funds and frequently they do not even have the financial strength to permit them to borrow the money needed for development. A project financing can sometimes be arranged in such a way as to solve this dilemma. A typical project financing will not provide the answer to the "little guy's" problem because most project financings require that the sponsors of the project provide completion undertakings and sometimes other undertakings. These undertakings are often a prerequisite to obtaining financing, and if the sponsor is not financially strong enough to provide the comfort that the lenders require, then the sponsor will have difficulty obtaining financing no matter what undertakings are offered. However, with a little imagination and the right set of circumstances, a project financing can sometimes provide the solution to the small mining company's problem. The Strathcona Sound Project is unusually suited as a case study because the sponsor, Mineral Resources International Limited,(MRI) was able to arrange a project financing for the development of the project even though the lenders probably would not have been willing to loan a similar amount of money direct to MRI based on the full faith and credit of MRI's balance sheet. The way that MRI was able to arrange this financing makes for an interesting story. THE CASE In early 1974, MRI owned 100% of a small to medium sized zinc - lead - silver massive sulfide deposit (Property) located 475 miles north of the Arctic Circle less than two miles from deep water on Strathcona Sound which is a shipping zone in the Canadian Arctic. The Property was situated at a desolate location except for an Eskimo settlement (Arctic Bay) which was about 20 miles west of the Property. In other words, the project required that complete infrastructure would need to be installed in this far northern location. Independent reserve and feasibility studies (Study) had been completed on the Property which confirmed a total of 6,825,000 tons of reserves classified and summarized as shown below on Table I: [ ] These reserves were based on 229 diamond drill holes totalling 58,909 feet and were established on a cut-off grade of 7% zinc and a minimum mining height of seven feet. The overall mining recovery rate was estimated at not less than 85% and not more than 90%. The feasibility study indicated that it would cost an estimated $45,044,000 to develop an underground mine, a concentrator, a town-site, a power plant, storage facility, loading dock, a tailings disposal area and an airstrip on the Property with an annual capacity of 525,000 tons of ore per year. The construction period was expected to take two years and projected capital costs were broken down as set forth below on Table II:

Jan 1, 1985

By A. J. Teplitz, T. Bardeen

In the course of an investigation of lost circulation, a new tool has been developed which gives a qualitative measure of the relative velocity between the fluid column in the borehole and the tool. The position of a diaphragm in the side wall of the instrument depends on the flow through the device. This position is established by using the conductive borehole fluid in a potentiometric circuit. The instrument has high sensitivity and can detect changes in velocity as low as. 5 ft/min. Lost circulation mud additives do not interfere with the satisfactory performance of the tool. In a number of circulation losses of the pressure induced type, the instrument has shown that the losses were confined to extremely narrow zones (less than I ft), indicating that such ruptures occur in a more or less horizontal rather than vertical plane as has often been assumed. This pinpointing of the zone of loss is important in remedial procedures since it allows the treatment to be applied directly to the point of loss rather than to the entire open hole. The device can also be employed for indicating points of entry of water in producing wells. INTRODUCTION The need for an improved means of locating the positions of lost returns zones became evident during an investigation of lost circulation difficulties in the Gulf Coast area.1 With instrumentation available at the time, it had been learned that, contrary to common belief, the position of the thief zone responsible for a given loss seldom coincided with the point of bit penetration at the time the loss was encountered. In the majority of cases, the losses were found to be occurring at some distance removed from the bottom of the hole —sometimes as much as a few thousand feet. This information, along with other observations made during the investigation, led to improved techniques' for dealing with lost circulation problems. Highlighted, however, among the results of this work and of similar studies subsequently conducted in drilling operations in other parts of the country, was the indication that a considerable portion of the difficulty and expense involved in treating prolonged circulation losses is due to the unsystematic application of remedial measures to one or more apertures of unknown position. Basis of Tests It is worth considering that if the troublesome formation could somehow be transported to the surface where it could be directly observed, there would likely be little difficulty in readily effecting a seal. Although this is a decided oversimplification of the situation, it does appear that the chief obstacles to similar ease of handling of a lost circulation zone in a well are lack of visibility and of ready accessibility. The latter handicap is overcome to a considerable extent by placement techniques already in use, and other procedures now in the process of development are expected to offer further improvement. But in the matter of visual observation, the technique to be presently described appears to afford a quite satisfactory substitute.

Jan 1, 1957

By F. S. McNicholas

IN the writer's opinion the term "block caving" has been rather loosely applied to a general principle of mining, and therefore detailed classification of caving methods and draw, together with the characteristics required for each method, will fill a desired need. Selection of caving method should be made only after a study of all governing conditions, such as size of orebody, lateral and vertical extent of ore-body, attitude, treatment demands, possible resultant pressures, and cost and profit comparison of methods. Successful caving methods can be classified under six main headings: (1) Full-protected block caving, (2) semi-protected block caving, (3) unprotected block caving, (4) full-panel caving, (5) half block-panel caving, (6) block-panel caving. The methods and factors governing choice of method are shown in Table I. Full-protected Block Caving Full-protected block caving consists of develop-ing, undercutting, and drawing to exhaustion a block of ore of predetermined size without coordination of mining or draw with adjoining areas. The block is mined and drawn as an independent unit (Fig. 1). Full-protected block caving demands that mining and draw cannot be done against unconsolidated capping in adjoining caved and exhausted blocks. Two sides of block are against solid. Caved capping must be allowed to consolidate for a suitable period, usually not less than one year. Pillars may be left in lieu of consolidated capping (Fig. 2). The advantages of full-protected block, caving are: (1) A definite area is developed, mined, and drawn as a unit so that all work may be completed, the block drawn to exhaustion in the minimum length of time, and the area then abandoned. (? Production is not restrained because of coordina1, on with adjoining areas. (3) Records of draw and caved reserve of ore are good. Upon abanwnment of the block, accountability for production is closed out with no carry-over to adjoining areas. The disadvantages of full-protected block caving are: (1) Side dilution from the draw adjacent to the consolidated capping may be serious, particularly where capping does not consolidate sufficiently in the allotted time. (2) Boundary weakening is needed on the solid sides of the block except in weak rocks. (3) Maximum cantilever and compression effect to aid caving and fragmentation may not be secured since the draw should proceed from the solid to the consolidated capping to minimize side dilution. However, undercutting from the loose (caved capping) to the solid with a slight initial draw in the same manner will develop cantilever effect. (4) A period of at least one year, more is usually desirable, must be allowed for caved capping ,to consolidate before mining the adjoining block, depending upon the characteristics of the capping. (5) Capping may not consolidate sufficiently in the time that can be allowed. Full-protected block caving is indicated where: (1) The ground is weak and heavy and workings

Jan 1, 1952

By Leendert de Witte

A review is given of the principles on which recently proposed methods of electric log interpretation in shaly sands are based and of the evidence brought up in support of the theoretical derivations. It is. pointed out that the qualitative techniques suggested to date have a tendency to be too pessimistic in the prediction of the presence of commercial hydrocarbon accumulations. In the quantitative treatment, a new concept is introduced, namely that of strongly reduced activity of the double layer counter ions which are present near the negatively charged rock surfaces. This lemmu when applied to the calculation of the equilibrium concentratiotls of interstitial waters yields a set of very simple relations. The resulting expressions for electrochemical potentials across rock samples appear in satisfactory agreement with laboratory experiments. The formulae obtained for the electrical conductivity of shaly formatioris are of the same form as those arrived at empirirally by previous workers. Combination of the expres.riorls for potentia1s and conductivities gives a direct proof of the Tixier relation which states that for shaly water sands the product of apparent formation water resistivity and apparent formation factor equals the resistivity of the sand 100 per cent .saturated with formalion water and which was verified by the work of Wyllie and Perkins and their co-workers. The relations for the resistivities and spontaneous porer11inI.s have been extended to the case of hydrocarbon hearing shaly formations, thus laying a formal basis for the quantitative interpretation of electric logs in shaly oil sands. INTRODUCTION The presence of disseminated clays in porous rocks saturated with electrolytic solutions has a strong influence on the transference of ions taking place under electrical or chemical potential gradients. Both the electrochemical emf's in evidence on the SP curves of electric logs and the electrical conductivity measured on resistivity logs arc directly dependent on the ionic transference in the interstitial waters of the formations traversed by boreholes. A large number of researches have been carried out on the nature and magnitude of the effects of clays on ionic transference. The most recent of these have been described in papers by McCardell and Winsauer,1 2 Wyllie and Southwick,3 poupon, Loy, and Tixier,4 and by Perkins et al.5 Most of these authors consider the effects of the clays as due to the fixed negative charges on the clay lattice. These charges cause the formation of diffuse surface layers with a high concentration of positive ions. The internal solution of the shaly reservoir rock has therefore a different ionic composition and concentration than the electrolyte with which it is in equilibrium (connate water produced from the formation or mud filtrate by which the formation is invaded). To calculate the equilibrium concentration of the internal solution, use is made of the Donnan6 relation, which states that the mean ionic activities of the internal solution and of the external electrolyte must be equal. From this and the

Jan 1, 1956

By B. A. Rogers, K. O. Stamm

BECAUSE it is the basis of the economically important operation of hardening steel by quenching, the A3 transformation in iron has been the subject of numerous investigations. Although the contributions to this subject are interesting, no general review will be given here. Readers who care to follow the matter further are referred to the comprehensive summary by Cleaves and Thompson,1 which covers the literature to about 1935. Their references to 53 papers on the subject suggest that further investigation is hardly justifiable. However, considerable interest has developed recently concerning the reversibility of the transformation. From thermodynamic considerations, the transition ought to occur at the same point on heating or cooling, if the change of temperature is sufficiently slow. Yet all of the earlier investigators found a difference of several degrees. Burgess and Crowe,2 who used thermal methods, obtained average temperatures of 912° for Ac3 and 900°C. for Ar3 on electrolytic iron. Their data indicate a considerable range of temperature over which the change occurs, both on heating and on cooling. Terry3 measured the susceptibility in the critical range and estimated from the steepest parts of his curves that Ac3 came at 9180 and Ar3 at 903°C. Ishiwara4 was one of the first investigators to report a shorter interval between the temperature of the change in the two directions. He measured the change of susceptibility of kaolin-coated samples of steel, in a hydrogen atmosphere, at rates of heating and cooling so low that about 3 or 4 hr. were required for the transformation to complete itself. His results show some variability between samples, but indicate that the difference between Ac3 and Ar3 is in the vicinity of 6°C. Roberts and Davey5 measured the space lattice in pure iron in the vicinity of 900°°C. and concluded that a change occurs reversibly between 907° ± 3° and 9100 ± 3°C., probably between 907° and 910°C. Wells, Ackley, and Mehl6 made dilatometric determinations of the Ac3 and Ar3 points in samples of hydrogen-treated carbonyl iron maintained under a vacuum. They used three rates of heating and cooling: 2°, '1/2°, and 1/8°C. per min. and found the spread between the two points decreased with low rates. At the slowest rate, the Ac3 transition occurred at 909° to 909.5°C. and the Ar3 change at 907°C. in three of the samples believed to contain the lowest percentages of alien elements. They concluded that if the rate of temperature change and the content of alien elements were low enough, the A3 transformation would be completely reversible at 909.5° ± I°C. The question of reversibility is an interesting one and when some iron with especially small percentages of alien elements became available the opportunity to conduct an investigation was welcomed. This iron was prepared by the Division of

Jan 1, 1941

By L. P. Davidson

ThE new electrolytic zinc plant of the American Zinc Company of Illinois commenced operation in April 1941. The simple flowsheet using the standard current density and the economic reasons that dictated it are given herewith. The Evans-Wallower Zinc Co. built an electrolytic zinc plant at Monsanto, Ill., in 1929 and operated it for about two years. The plant stood idle from 1932 and was purchased by the American Zinc Co. in 1940. Because of the condition of the equipment, excepting the motor generator set, a complete rebuilding was necessary. The Fairmont City plant of the American Zinc Co. could treat the leach residues, the purification cake and the skimmings from the melting furnace in its various plants. This possibility permitted a simple flowsheet with good economic results. The flowsheet is shown in Fig. I. The calcined concentrates are leached in mechanically agitated tanks with spent electrolyte and such ferric iron solution as necessary. When the acid has been neutralized and the iron coagulated, the fluid is discharged to settling tanks. The underflow from these thickeners is filtered on a Moore filter; the filter cake leaves the plant for retreatment and the filtrate joins the thickener overflow. Zinc dust is added to this solution until the copper and cadmium are precipitated. The pulp is filtered through Shriver presses, which deliver the purified solution to stor- age tanks, and the copper-cadmium-zinc cake is shipped for retreatment and recovery of these three metals. The purified solution is electrolyzed; the regenerated acid is returned for use in the leaching plant and the cathode zinc, after stripping, goes to the melting furnace, from which it is cast in slabs. The skimmings from the melting furnace are shipped to the Fairmont City plant for reduction to metal in the retort furnaces. The choice of this simple flowsheet was made possible only because of the facilities of the Fairmont City plant. The long leaching pried, with high acid content and high temperature which characterize the high-density process, gives a higher zinc extraction but also dissolves more impurities, which must be removed. The same is true to a lesser degree of the multi-step leaching of the western low-density plants. By the sacrifice of some initial extraction, solutions can be obtained that are relatively easy to purify and give good ampere efficiency. This loss in initial extraction is made up in the retreatment of the residues in the Waelz plant. The impurities that accompany the zinc thus extracted are inconsequential when the Waelz product is treated in a distillation plant. It was recognized that this flowsheet would require a somewhat greater amount of sulphuric acid—-eithcr as acid or as sulphate sulphur in the calcine—because of poorer washing. The sulphuric acid plant at Fairmont City could deliver 60" Bè. acid to compensate for the sulphate loss and the cost would be less than the cost of more intensive washing.

Jan 1, 1943

By L. P. Davidson

ThE new electrolytic zinc plant of the American Zinc Company of Illinois commenced operation in April 1941. The simple flowsheet using the standard current density and the economic reasons that dictated it are given herewith. The Evans-Wallower Zinc Co. built an electrolytic zinc plant at Monsanto, Ill., in 1929 and operated it for about two years. The plant stood idle from 1932 and was purchased by the American Zinc Co. in 1940. Because of the condition of the equipment, excepting the motor generator set, a complete rebuilding was necessary. The Fairmont City plant of the American Zinc Co. could treat the leach residues, the purification cake and the skimmings from the melting furnace in its various plants. This possibility permitted a simple flowsheet with good economic results. The flowsheet is shown in Fig. I. The calcined concentrates are leached in mechanically agitated tanks with spent electrolyte and such ferric iron solution as necessary. When the acid has been neutralized and the iron coagulated, the fluid is discharged to settling tanks. The underflow from these thickeners is filtered on a Moore filter; the filter cake leaves the plant for retreatment and the filtrate joins the thickener overflow. Zinc dust is added to this solution until the copper and cadmium are precipitated. The pulp is filtered through Shriver presses, which deliver the purified solution to stor- age tanks, and the copper-cadmium-zinc cake is shipped for retreatment and recovery of these three metals. The purified solution is electrolyzed; the regenerated acid is returned for use in the leaching plant and the cathode zinc, after stripping, goes to the melting furnace, from which it is cast in slabs. The skimmings from the melting furnace are shipped to the Fairmont City plant for reduction to metal in the retort furnaces. The choice of this simple flowsheet was made possible only because of the facilities of the Fairmont City plant. The long leaching pried, with high acid content and high temperature which characterize the high-density process, gives a higher zinc extraction but also dissolves more impurities, which must be removed. The same is true to a lesser degree of the multi-step leaching of the western low-density plants. By the sacrifice of some initial extraction, solutions can be obtained that are relatively easy to purify and give good ampere efficiency. This loss in initial extraction is made up in the retreatment of the residues in the Waelz plant. The impurities that accompany the zinc thus extracted are inconsequential when the Waelz product is treated in a distillation plant. It was recognized that this flowsheet would require a somewhat greater amount of sulphuric acid—-eithcr as acid or as sulphate sulphur in the calcine—because of poorer washing. The sulphuric acid plant at Fairmont City could deliver 60" Bè. acid to compensate for the sulphate loss and the cost would be less than the cost of more intensive washing.

Jan 1, 1943

By A. J. Miles, A. D. Topping

in this paper, the theory of elasticity has been applied to the rock about a deep well, It is assumed that the rock has a modulus of . elasticity and a Poisson's ratio and that the theory of elasticity applies. It is necessary to know or assume the state of stress existing in the rock before it is penetrated by the well drill. The application of this theory indicates that stress concentration of shear, tensions, and compressions about the bore hole are of a high order. This is particularly true when a horizontal compressive stress exists in one direction only in the formation before drilling. If such an initial state of stress exists before drilling, then the rock will have stress concentrations of both tension and compression at the same elevation and of such magnitude that failure of the rock is likely. Accompanying these is a shearing stress of large proportion which is likely to produce spalling of the well walls. Internal pressure applied to the well bore will relieve the extreme compression but not the tension and has little effect upon the shear. Plastic deformation of the rock through a geological time tends to mitigate the stress concentrations. IntroductioN It has long been known that the stresses about holes and re-entrant corners of elastic solids under the influence of loads are different and generally more intense than those imposed upon the body else- where. Stress concentration at a re-entrant corner can be reduced by increasing the radius of the fillet at the corner. Stress concentration at the end of a crack in a plate undergoing either tension or compression Can be relieved appreciably by drilling a hole at the very end of the crack. Also, stresses can be increased in an elastic body in tension or compression by making a hole in it. The stress concentration is greatest at the edge of the hole. Considerable knowledge of the stresses which exist about the bore hole of a deep well may be had by applying our knowledge of engineering mechanics; or more particularly the theory of elasticity. It is, of course, necessary to make the assumption that the rock is elastic and behaves as an elastic solid, that is, that it obeys Hooke's law, has a modulus of elasticity, and a Poisson's ratio. It is also necessary to know, Or assume, the state of stress which exists in the rock prior to the penetration of the drill. With this knowledge it is possible to compute the stresses about the bore hole. The problem can be simplified by considering several simple cases separately and then by applying the principle of superposition to solve the more complex cases which are made up of the simpler ones. Case i—Rock Strata in Compression Penetrated by a Hole This case was first worked out by G. Kirsch* for structural material, but applies equally well to a horizontal rock strata in a state of in in one direction

Jan 1, 1949

By John W. Vanderwilt

The unpredictable behavior of ground movement and subsidence has complicated the problems that attend the extraction of large quantities of ore. Special studies, particularly relating to coal mining, have yielded such a voluminous literature and so many involved controversial theories that a partial review would be difficult. Limited space makes any kind of a review impractical. The features to be considered cover only a relatively small part of the broad problems of ground movement and subsidence, but it is believed that this small part is critical. The practical aspects are important, since they bear directly on safety of mine workings, on recovery of ore and on dilution of ore in block caving and related systems for extracting large quantities of rock. The ground movement to be described occurs outside the vertical boundaries of a caved block in the area that is commonly referred to as being in the "zone of draw." "Draw" is a term that originated in the subsidence problems related to coal mining, and it is defined by a line drawn from the margin of the area caved underground to the most distant fracture at surface on the same side of the caved area as shown in Fig. I.' A line thus drawn is called the cave line, and its angle with respect to the horizontal is the cave angle or angle of draw. It is understood that the line is taken normal to the limit of mining, and in a vertical plane. The prevailing theories as to draw and angle of draw assume that appreciable movement occurred along the cave line, which has been described as a fracture resulting from the shearing action brought about by the weight of the overlying load. Fig. 3 shows diagrammatically the mechanics of ground movement adjacent to an area of subsidence according to the prevailing theory of draw (A, from Royce2) and, for comparison, ground movement observed in the Climax mine (B). The text in Peele's Handbook2 referring to Fig. 2 does not state the meaning of the "original position of top of workable ore" in the rectangular space above "ore in place," and the arrows are not explained. However, this presentation is most concerned with the zones outside the rectangle. According to the prevailing theory, as shown at the extreme left under A, Fig. 2, the vertical tension cracks at surface change at a shallow depth to shear fractures forming the cave line, and it is assumed that appreciable movement takes place along the cave line toward and into the subsiding caved block. The mechanics of ground movement observed in the Climax mine, as shown under B, Fig. 2, does not accord with the prevailing theory, particularly as regards the cave angle and draw. The vertical tension cracks seen at surface die out at depths of 150 to 225 ft. and shear fractures do not develop. Movement is confined at surface to a mantle of rock 50 to roo ft.

Jan 1, 1949

By H. K. Work

THE Bessemer process is one of the most interesting methods of making steel. At one time it was by far the most important. In recent years, however, it has steadily lost ground to the open-hearth process. The forces working against this method of steelmaking are partly economic and partly metallurgical.' In this paper, dealing as it does with the control of the process, the metallurgical factors alone will be considered, although it is obvious that economic factors must play a part in determining the ultimate status of the Bessemer process. This discussion has been limited in another respect-it deals primarily with the acid Bessemer process in bottom-blown converters, although much of the information is applicable to basic and side-blown converters. The fact that open-hearth steel has superseded Bessemer steel to a large extent has tended to create an impression that Bessemer steel is inferior. As a matter of fact, Bessemer steel is actually superior to open-hearth for many applications.2 There are, however, definite metallurgical limitations to the use of Bessemer steel, resulting largely from two factors: (I) the physical properties conferred by nitrogen and phosphorus, and (2) the variability from blow to blow. These, of course, are not entirely independent, since some of the variability covered in the second item is undoubtedly due to nitrogen. But the variability is also caused by other factors. One of these is the relatively small size of the Bessemer heats. Because of this, a given shipment of Bessemer steel is more likely than a shipment of open-hearth steel to contain the product of several heats, each with its own distinctive and slightly different characteristics. Added to this is the fact that the refining of Bessemer steel proceeds so rapidly that the timing of the end point is limited to a matter of seconds, whereas the finishing period in the open hearth extends over a period of one or two hours and the timing of the end point may vary by several minutes without seriously affecting the product. There is no doubt that this has contributed to the variability of Bessemer steel and has led to the use of open-hearth steel in many optional applications. That Bessemer steel may vary is not necessarily objectionable, and it may even prove an advantage, providing a precise control is available to secure the desired qualities for any specific application. With this in mind, a comprehensive research program was undertaken, one phase of which was directed toward securing more accurate control of the blow. The results have been encouraging, and it is the purpose of this paper to describe a method in which modern scientific instruments, based on photocells, are currently being employed to assist the blower. THE CONTROL PROBLEM In this day of scientific control of technical processes, where the operating

Jan 1, 1941

By C. G. Southmayd

ANYONE who has been confronted with the problem of predicting the performance of a sand-pump installation is vitally aware of the dearth of precise information that has been published on this important subject. Such data as have been collected are not readily available in a concise and readily usable form, so that many operators would find it a considerable chore to find the pertinent information required to undertake a detailed study. The purpose of this paper is to assemble such established data, correlate them with field experience and outline the factors that must be appraised in the determination of a satisfactory pump installation. The transportation of solids in solution is of vital interest to every mill superintendent and operator, and many of the factors that are involved in this hydraulic problem vary widely from installation to installation, and in some cases even from time to time on any one installation.. These include: type of solids (including shape of particles), size of solids (grind), percentages of fines (slimes), dilution of pulp, contour of pipe line, type of pipe, age of pipe line, effect that diameter of pipe has on characteristic flow conditions, and other factors. Some of these have been fairly well determined by experimental work but many still must be established through interpolating or extrapolating between values that have been derived from known field conditions. Most problems primarily concern the transportation of a definite weight of dry solids from one specific location to another. The type of material, shape of particles, grind and percentages of fines are established and very often the dilution at which the solids must be handled as well. The problem then evolves into a determination of the size, type and contour of the pipe line and the net effective head against which the pump must operate. Before discussing the determination of the head, it might be well to review the interrelationship between the pump discharge (capacity), the head developed by the pump and the pump speed, which will apply to any centrifugal pump installation. EFFECT OF PUMP SPEED Basically, the head developed by a centrifugal pump varies as the square of the pump speed and the discharge as the first power of the speed. However, even at constant speed a centrifugal pump will operate over a wide range of capacities, depending upon the head that must be developed to deliver the liquid or pulp to the end of the pipe line. This is shown graphically in Fig. I. If the pump in question is being driven at a constant speed of 900 r.p.m. it will deliver 500 U. S. gal. per min. against a head of 56 ft., 800 U. S. gal. per min. against a head of 50 ft., and so on. In other words, at this speed the capacity of the pump will be determined and limited by

Jan 1, 1946

By J. K. Edgar

FOR a number of years the production and use of super-purity aluminum (better than 99.99 pct) has been steadily increasing. High-grade lots of such aluminum show certain outstanding characteristics not found in lower grades containing principally silicon, iron and copper as impurities. One such characteristic is the so-called "self annealing," that is, the recrystallization of the heavily cold worked metal at room temperature.' Interest therefore is aroused as to the effects of the impurities. It is well known that the amounts of silicon and copper which occur in aluminum of better than 99.95 pct are completely soluble, at least at elevated temperatures (above 200°C). Iron, on the other hand, is known to be fairly insoluble in solid aluminum. Thus, a knowledge of the limits of this solubility would be of considerable use in studying the characteristics of the high purity metal. All investigators have agreed that iron has very low solubility in solid aluminum. Rosenhain, Archbutt and Hanson2 reported traces of an aluminum-iron phase in the "purest samples of aluminum obtainable." Gwyer and Phillips3 reported that an iron constituent was visible under the microscope in metal containing ".0088 per cent iron." Roth1 found that in the solid state the solubility of iron in high purity aluminum was 0.01, 0.01, 0.017 and 0.022 pct at 225, 320, 500 and 600°C respectively. Dix5 working with alloys containing less than 0.03 pct impurities, concluded from microscopic and chemical analyses of eutectic areas that the eutectic composition was close to 1.7 pct iron. Dix placed the eutectic temperature at 655°C'. Archer and Fink,6 using high purity aluminum-iron alloys, found that the hypoeutectic liquidus intersects the eutectic horizontal at 1.7 pct. This is in fair agreement with the investigation of the aluminum-iron system by Gwyer and Phillips who placed the eutectic at 1.89 pct iron with a freezing point of 653° PREPARATION AND CHEMICAL ANALYSIS OF ALLOYS Electrolytically refined aluminum (99.991 pct aluminum) and a high purity aluminum-iron alloy (11.45 pct iron) were used in the preparation of the alloys for this investigation. To aid in controlling the iron content of the experimental alloys, an alloy of lower iron content was prepared first from these materials. The high purity aluminum was melted and heated to about 700°C in a plumbago crucible coated with alundum cement and the aluminum-iron alloy was then added. The alloy was thoroughly stirred, fluxed and skimmed and then chill-cast into notch bars. The analyses of the three materials are given in Table I. The alloys for the determination of the solid solubility of iron in aluminum were prepared by melting 600 g total of the aluminum plus the required quantity of the aluminum-iron alloy (No. 92531). These

Jan 1, 1948

By K. O. Stamm, B. A. Rogers

Because it is the basis of the economically important operation of hardening steel by quenching, the A3 transformation in iron has been the subject of numerous investigations. Although the contributions to this subject are interesting, no general review will be given here. Readers who care to follow the matter further are referred to the comprehensive summary by Cleaves and Thompson,l which covers the literature to about 1935. Their references to 53 papers on the subject suggest that further investigation is hardly justifiable. However, considerable interest has devel oped recently concerning the reversibility of the transformation. From thermo-dynamic considerations, the transition ought to occur at the same point on heating or cooling, if the change of temperature is sufficiently slow. Yet all of the earlier investigators found a difference of several degrees. Burgess and Crowe,2 who used thermal methods, obtained average temperatures of 912" for Ac3 and 900°C. for Ar3 on electrolytic iron. Their data indicate a considerable range of temperature over which the change occurs, both on heating and on cooling. Terry3 measured the susceptibility in the critical range and estimated from the steepest parts of his curves that Ac3 came at 9I8° and Ar3 at 903°C. Ishiwara4 was one of the first investigators to report a shorter interval between the temperature of the change in the two directions. He measured the change of susceptibility of kaolin-coated samples of steel, in a hydrogen atmosphere, at rater of heating and cooling so low that about 3 or 4 hr. were required for the transformation to complete itself. His results show some variability between samples, but indicate that the difference between Ac3 and Ar3 is in the vicinity of 6°C. Roberts and Davey5 measured the space lattice in pure iron in the vicinity of 900°C. and concluded that a change occurs reversibly between 907' 3" and 910" 3°C., probably between 907" and 910°C. Wells, Ackley, and Meh16 made dilatometric determinations of the Ac3 and Ar3 points in samples of hydrogen-treated carbonyl iron maintained under a vacuum. They used three rates of heating and cooling: 2°, ½°, and .?°C. per min. and found the spread between the two points decreased with low rates. At the slowest rate, the Ac3 transition occurred at 909° to 909. 5°C. and the Ar3 change at 907°C. in three of the samples believed to contain the lowest percentages of alien elements. They concluded that if the rate of temperature change and the content of alien eiements were low enough, the A3 transformation would be completely reversible at 909.50 + 1°C. The question of reversibility is an interesting one and when some iron with especially small percentages of alien elements became available the opportunity to conduct an investigation was welcomed. This iron was prepared by the Division of

Jan 1, 1942

By B. A. Rogers, K. O. Stamm

Because it is the basis of the economically important operation of hardening steel by quenching, the A3 transformation in iron has been the subject of numerous investigations. Although the contributions to this subject are interesting, no general review will be given here. Readers who care to follow the matter further are referred to the comprehensive summary by Cleaves and Thompson,l which covers the literature to about 1935. Their references to 53 papers on the subject suggest that further investigation is hardly justifiable. However, considerable interest has devel oped recently concerning the reversibility of the transformation. From thermo-dynamic considerations, the transition ought to occur at the same point on heating or cooling, if the change of temperature is sufficiently slow. Yet all of the earlier investigators found a difference of several degrees. Burgess and Crowe,2 who used thermal methods, obtained average temperatures of 912" for Ac3 and 900°C. for Ar3 on electrolytic iron. Their data indicate a considerable range of temperature over which the change occurs, both on heating and on cooling. Terry3 measured the susceptibility in the critical range and estimated from the steepest parts of his curves that Ac3 came at 9I8° and Ar3 at 903°C. Ishiwara4 was one of the first investigators to report a shorter interval between the temperature of the change in the two directions. He measured the change of susceptibility of kaolin-coated samples of steel, in a hydrogen atmosphere, at rater of heating and cooling so low that about 3 or 4 hr. were required for the transformation to complete itself. His results show some variability between samples, but indicate that the difference between Ac3 and Ar3 is in the vicinity of 6°C. Roberts and Davey5 measured the space lattice in pure iron in the vicinity of 900°C. and concluded that a change occurs reversibly between 907' 3" and 910" 3°C., probably between 907" and 910°C. Wells, Ackley, and Meh16 made dilatometric determinations of the Ac3 and Ar3 points in samples of hydrogen-treated carbonyl iron maintained under a vacuum. They used three rates of heating and cooling: 2°, ½°, and .?°C. per min. and found the spread between the two points decreased with low rates. At the slowest rate, the Ac3 transition occurred at 909° to 909. 5°C. and the Ar3 change at 907°C. in three of the samples believed to contain the lowest percentages of alien elements. They concluded that if the rate of temperature change and the content of alien eiements were low enough, the A3 transformation would be completely reversible at 909.50 + 1°C. The question of reversibility is an interesting one and when some iron with especially small percentages of alien elements became available the opportunity to conduct an investigation was welcomed. This iron was prepared by the Division of

Jan 1, 1942

By N. H. Fisher

GEOGRAPHICAL DISTRIBUTION THE most important known deposits in Australia of what are commonly referred to as the beach-sand minerals are along the most easterly part of the Australian coast, between Southport, 17 miles north of the Queensland-New South Wales border, and Ballina, 50 miles south of the border, and most of the production has come from this area (Fig 1). Smaller deposits are known to occur farther to the south at intervals for several hundred miles, and beaches have been worked at Yamba, 96 miles south and Woolgoolga, 150 miles south of the border and at Swansea, 60 miles north of Sydney. Important deposits have been shown to exist on north Stradbroke Island and others have been located farther to the north, as far as Tin Can Bay at the south end of Frazer Island. (Fig 2). Table I gives the list of operators with the location of their deposits and workings, their approximate maximum monthly capacity expressed in tons of heavy mineral produced by their concentrating plants before separation into individual mineral concentrates, their methods of mining and concentrating the minerals, and the products obtained. This table applies as of June 1948, but all the operators are remodeling or improving their plants and plant practices will be modified accordingly. In addition, active boring campaigns have been carried out by Alluvial Gold, Ltd., of Sydney, in the Cudgen-Cudgera area, and by Zinc Corporation. Ltd., of Melbourne, on Stradbroke Island, and in other places. PHYSIOGRAPHY Submergence of the order of 100 to 200 ft at the close of the Pleistocene period left the pre-existing hills as promontories and the valleys as deep inlets. Wave action has built bay-bars and sandspits in a northerly direction from the headlands, and lakes and marshes have formed between these bars and the initial post-submergence coast line. These lakes and swamps have been or are being filled in by river-borne sediments or wind-blown sand. Beasley1 has presented evidence that suggests a recent emergence of the coast line of about 10 ft. The evidence for this belief is the presence of a black sand seam 1/3 mile inland and 17 ft above sea level (Fig 3), and although it is not entirely certain that this seam is of beach formation and owes nothing to windblown concentration, other evidence supports the suggestion of recent emergence. Such emergence would undoubtedly aid the formation of bars and sandspits and the easterly progress of the beach front, leaving a series of parallel dunes (Fig 4). This belt of north-south coastal dunes ranges up to 1/2 mile in width and as many as 15 lines of dune have been counted (Fig 3). The foredune is generally the highest, up to 25 ft high, and there is in many places a flat platform in front of the dune known as the berm. The dunes behind the foredune are lower and less well defined

Jan 1, 1947

By Gerhard Derge

The extension of metallurgical control of steelmaking processes has always made it desirable to have some quick method for determining the oxygen content of molten steel. To meet the practical demands of the steel industry, this method must also be simple enough so that the sampling can be done by the regular furnace crew. This requirement was kept in mind continually in the work to be described. An oxygen value is required for proper control, whether it be of a rimming steel or of a fully killed steel. However, two factors have discouraged the development of such direct methods: i. The reaction C + FeO Fe + CO is rapid enough to make the correct sampling Of the bath a difficult problem. The most generally accepted means of circumventing this difficulty have been the aluminum-killed bomb test of McCutcheon and Rautiol and the aluminum-killed spoon test of Herty.2 The theory of these tests is that all of the oxygen in the iron is converted to Al2O3, which can then be determined by chemical methods. Even when simplified so that the analysis is made by a measurement of turbidity, this method is too slow to be used in routine control. Furthermore, the results obtained have never been entirely satisfactory, and some of the reasons for this will be discussed later in this paper. z. The ordinary chemical methods of analysis for oxygen in steel are not reliable. The only analysis that seems to possess sufficient dependability to be of value is vacuum fusion,3 and the apparatus and technique developed for this have been too complex and slow for routine work. Indirect Methods Indirect methods of estimating the oxygen have been resorted to in mill practice. Generally these depend upon the chemical equilibria involved. The oxygen in the bath is related to other components in the slag or metal that can be analyzed the readily. These methods have many difficulties in common. Steelmaking processes involve a complicated set of interrelated reactions, all of which tend to approach equilibrium at varying rates. The degree to which any particular equilibrium is approached is not well established. Moreover, a proper use of theoretical equilibrium constants requires a more extensive knowledge of the activities of the con- than we now have. This is well illustrated by the irregularities observed when trying to determine the oxygen in the metal by its ratio to the iron oxide in the slag. Equiliblium relations may be used mole readily if they are evaluated by plant experience, but the extent of approach to equilibrium remains an undetermined variable and lack of an entirely satisfactory mean, of determining oxygen for the calibration is felt keenly, For example, the statistical analysis of the relation between carbon and oxygen4.6 illustrates that even iia a single plant wide variations exist under llormal conditions of operation. Never. theless, this is one of the best methods now

Jan 1, 1943

By E. E. Schumacher, G. S. Phipps, H. M. Bouton

The seriousness of the present tin scarcity has stimulated large consumers of this vital metal to develop drastic conservation measures in order to extend the available supplies to cover the emergency period. By devising new soldering methods and alloys the Bell System has contributed a substantial share in the tin conservation effort. Fortunately, the changes, as far as can be determined now, have not introduced weakness into the soldered joints. Some of the new procedurcs were already in the process of development at the onset of the emergency, while others were devised under its stress. In some instances, the newly developed solders were found to be more difficult to use than the alloys previously available, and would not have been introduced under normal conditions. One major change made that previously had been under consideration will result in large savings of tin. Unless service difficulties are encountered, this modification gives promise of remaining after the emergency has passed. The change involves a reduction in the amount of solder placed on a wiped joint between the cable sheath and the sleeve. Instead of the customary full sized wiped joint, a wipe of fillet proportions is formed. Through this change, a solder saving of more than 60 per cent per joint can be realized. Plumbers and cable splicers for many years have joined lead pipes and cable sheath by a soldering process called " wiping." The name is an apt description of the operation. For a wiped joint, the sections to be united are heated by molten solder poured over their surfaces, and the resulting semiliquid mass is manipulated by wiping with cloth pads to a well rounded symmetrical form like the one shown in Fig. I. The operation requires considerable skill on the part of the splicer and close control of the composition of the solder. At first consideration, the problem of tightness in such joints seems simple but experience shows that even under the best conditions the fissures frequently found in the solder occasionally link and form a path that allows leakage to occur. In telephone cables not maintained under gas pressure, such leaks permit the entrance of water, which wets the paper-covered conductors and thereby impairs the insulation value and causes service interruptions. Ry going to an extreme and wiping off all the solder in excess of a fillet, it has been found that many causes of porosity are eliminated. Figs. 2 and 3 show cross sections of joints wiped in the old and the new ways. The saving in solder, and consequently in strategic tin, is evident. The field splicing forces find that joints are easier to make by the new method and are less likely to be porous. The metallurgical considerations that are responsible for the success of the fillet wipe are of interest. Much has been written about the wiping process of soldering cable joints and the many requirements of a good wiping solder have frequently been listed. The success of the procedure described

Jan 1, 1943