Search Documents

By J.B. Pullen

The United Verde mine is in the north central part of Arizona, on the northeasterly slope of the Black Hills, near the town of Jerome. Ore was first discovered in the district about 1875, and the first mining claims were located by M. A. Ruff-ner and associates in 1877. In 1888 the late Scnator William A. Clark secured control of the property and under his ownership it developed into one of the country's most important copper producers. The property was sold to the Phelps Dodge Corporation in 1935, and since then has been under this Corporation's management. Except for shutdowns caused by general world-market conditions, production has been continuous from 1890 to date. Geology The mineralized zone ranges in area from approximately 12 acres to less than 5 acres. All mineralization occurs in the pre--Cam-brian intrusives. The first intrusion, according to geologic records, was the quartz porphyry, which later was intruded by augite diorite. Following the diorite intrusion through a series of intrusions of lesser magnitude, a pipelike mass of massive sulphide, quartz and rock was formed. The diorite forms the hanging wall of this mass, and the porphyry the footwall. Between the footwall and the sulphide a band of chlorite schist was formed, probably owing to metamorphic conditions. Commercial ore occurs along the contact of the schist and sulphide extending into the sulphide, sometimes entirely through the schist, and fingering out into the porphyry. The ore deposit was formed by replacement similar to deposits formed in limestone areas. Faulting and deformation occurred in pre-Cambrian times and again in the Tertiary period, removing approximately 2000 ft. from the top of the main United Verde ore body, forming the United Verde Extension ore body, the only other major ore body in the district. Major development work has shown that the sulphide mass extends to the 3300-it. level, and diamond drilling below this level has indicated that the mass might extend below the 3700-ft. level, but in a diminished quantity. While many copper minerals exist in the mine, the chief commercial mineral is chalcopyrite. Aplan and vertical section of the mineralized zone showing the principal geological eatures is shown in Figs. I and 2. General Description and Physical Condition or Mine After over 50 years of active production, ore still exists on almost every level of the mine. This condition is due to many causes —-mine fires, which broke out as early as 1894, caused the abandonment of certain areas; subsidence and ground movements retarded the cleaning up of others. Furthermore, in the early days there was such an abundance of ore that when mining became dificult it was a simple matter to replace the production by going to a deeper level. Several attempts were made to recover the ore in the fire zone, both by glory-holing

Jan 1, 1943

By J. B. Pullen

The United Verde mine is in the north central part of Arizona, on the northeasterly slope of the Black Hills, near the town of Jerome. Ore was first discovered in the district about 1875, and the first mining claims were located by M. A. Ruff-ner and associates in 1877. In 1888 the late Scnator William A. Clark secured control of the property and under his ownership it developed into one of the country's most important copper producers. The property was sold to the Phelps Dodge Corporation in 1935, and since then has been under this Corporation's management. Except for shutdowns caused by general world-market conditions, production has been continuous from 1890 to date. Geology The mineralized zone ranges in area from approximately 12 acres to less than 5 acres. All mineralization occurs in the pre--Cam-brian intrusives. The first intrusion, according to geologic records, was the quartz porphyry, which later was intruded by augite diorite. Following the diorite intrusion through a series of intrusions of lesser magnitude, a pipelike mass of massive sulphide, quartz and rock was formed. The diorite forms the hanging wall of this mass, and the porphyry the footwall. Between the footwall and the sulphide a band of chlorite schist was formed, probably owing to metamorphic conditions. Commercial ore occurs along the contact of the schist and sulphide extending into the sulphide, sometimes entirely through the schist, and fingering out into the porphyry. The ore deposit was formed by replacement similar to deposits formed in limestone areas. Faulting and deformation occurred in pre-Cambrian times and again in the Tertiary period, removing approximately 2000 ft. from the top of the main United Verde ore body, forming the United Verde Extension ore body, the only other major ore body in the district. Major development work has shown that the sulphide mass extends to the 3300-it. level, and diamond drilling below this level has indicated that the mass might extend below the 3700-ft. level, but in a diminished quantity. While many copper minerals exist in the mine, the chief commercial mineral is chalcopyrite. Aplan and vertical section of the mineralized zone showing the principal geological eatures is shown in Figs. I and 2. General Description and Physical Condition or Mine After over 50 years of active production, ore still exists on almost every level of the mine. This condition is due to many causes —-mine fires, which broke out as early as 1894, caused the abandonment of certain areas; subsidence and ground movements retarded the cleaning up of others. Furthermore, in the early days there was such an abundance of ore that when mining became dificult it was a simple matter to replace the production by going to a deeper level. Several attempts were made to recover the ore in the fire zone, both by glory-holing

Jan 1, 1943

By Robert E. Green

Formulae are given for calculating the modes of wave propagation in a single-crystdl specimen possessing a given crystallographic orientation. Such calculations lead to determination of the orientation factor appearing in the Granato-Lucke theory for the attenuation of these waves due to dislocation damping. A detailed treatment is given for the case of an aluminum crystal possessing the orientation having a maximum Schmid fac -tor of 0.5. FOR a number of years the attenuation of ultrasonic waves propagating in metals has been used to investigate various phenomena causing internal friction.Most of the experiments were performed on polycrystalline test specimens and the waves were assumed to be propagating in an isotopic medium. However Alers 6 in 1955 and more recently Hikata et at. Chiao and Gordon,8 and Swanson and Green 10 have used measurements of attenuation of ultrasonic waves to study internal-friction changes in single crystals. These authors were concerned with the energy losses experienced by the ultrasonic waves due to dislocation motion induced by plastic deformation of the crystals. Alers measured the attenuation of 7 mc per sec ultrasonic pulses propagating in zinc single crystals before, during, and after plastic deformation. Simultaneously he measured the time-dependent plastic strain at constant stress in order to study the correlation between this strain and attenuation. The crystals were oriented in such a way that the applied stress provided a direct shear on the slip plane, thus causing the deformation to proceed by slip on this plane. At the same time the high-frequency sound pulses were sent through the crystal perpendicular to the slip plane. He found that the attenuation of transverse waves, the stress vectors of which lie in the slip plane, was very sensitive to the deformation. The polarization of the particle displacements, associated with these waves, relative to the applied static shear stress, and hence the direction of slip, had no obvious effect on the results. The attenuation of longitudinal waves was affected by the deformation only when the slip plane was not perpendicular to the propagation direction. This indicated that the attenuation was caused by dislocations introduced by the deformation and moving only in the slip plane. Hikata et al. made simultaneous measurements of attenuation, velocity changes, and stress-strain relations on aluminum single crystals deformed in tension. Both longitudinal and shear waves were used, at frequencies of 10 and 13 mc per sec. They placed emphasis on the choice of propagation modes and polarization of the ultrasonic waves, such that interactions between these waves and dislocations on selected slip systems could be investigated. They also selected specimens possessing specific crys-tallographic orientations, which allowed investigation as a function of the number of equally favored slip systems under the applied stress. They found that, for symmetrical orientations, the change of attenuation decreases with the increasing number of equally favored slip systems, i.e., in the order

Jan 1, 1964

By R. P. Carreker, R. W. Guard

True stress-true strain data are given for nominally pure molybdenum (99.95 pct) over the temperature range -196° to 1540°C (0.027 to 0.63 T/T). Strain rate sensitivity was determined by rate change tests and stress relaxation tests. Inhomogeneous yielding and strain aging effects were observed. The yield stress and tensile strength depend markedly on temperature below 400°C and are insensitive to temperature in the range 400' to 800°C. The ductile to brittle transition range is +25O to -25OC. Strain rate sensitivity and stress relaxation effects are very large near room temperature. THIS report presents data which were obtained as a part of a continuing program designed to document the deformation behavior of nominally pure metals over a wide temperature range.'" This research program is rooted in the conviction that sufficient tensile and creep data of appropriate quality and detail does not exist to provide precise phe-nomenological descriptions of the deformation behavior of pure metals as a function of temperature, strain rate, and grain size. Such knowledge is needed to provide a firm base for alloy design and an experimental framework to which theories of deformation must conform. These data also complement a parallel exploratory program investigating the properties of refractory metals, including molybdenum, and their alloys. Several important reviews and research reports dealing with the tensile properties of molybdenum as a function of temperature have appeared."-lo To a great extent the work to be reported in the present paper parallels that of Bechtold and of Pugh. The authors' results are in general agreement with those of Bechtold and Pugh. The principle differences be- tween the present experiments and those published previously are as follows: 1—Wire specimens prepared from arc cast molybdenum were used in the present experiments, bar specimens were used by others. Pugh used arc cast material while Bechtold's most extensive results" were obtained on powder metallurgy specimens. 2—Several different grain sizes were tested in the present experiments. 3—The testing range was extended to cover from -196°C to 1570°C (0.027 to 0.63 T/Tm). 4—The combination of wire specimens, high speed autographic recording, and a stiff testing machine permitted more detailed study of initial yielding. The principle contribution of the present paper is the demonstration of the relatively consistent mechanical properties of nominally pure arc cast molybdenum specimens of differing metallurgical history. Bechtold and Scotts have shown that arc cast and powder metallurgy molybdenum samples have comparable tensile properties in the range —75" to 200°C when processed to have the same re-crystallized grain size. Material The molybdenum used in this investigation was supplied by the Climax Molybdenum CO. Its metallurgical history is outlined in Table I; the final products were 0,030 in, diam wire specimens annealed at 1100' and 1375°C and 0.060 in. diam wire

Jan 1, 1957

By A. A. Watts, R. I. Jaffee, F. C. Holden, H. R. Ogden

Hypoeutectoid Ti-Cu alloys are responsive to heat treatment, and considerable variation of mechanical properties may be produced by transformation of the ß phase. Control of cooling rate, isothermal transformation, or quench tempering determine the transformation structure and properties. The transformation products are similar to those of carbon steel. THE equilibrium diagram for the Ti-Cu system has been studied by various investigators, and the most recent diagram is that determined by Jou-kainen, Grant, and Floe.' The titanium-rich portion of this diagram is reproduced in Fig. 1. The alloy compositions and annealing temperatures used in this work are shown. The Ti-Cu alloys containing up to 17 wt pct Cu are representative of an active eutectoid alloy system. Joukainen et a1.l have stated that ß phase cannot be retained on quenching and this has been confirmed in the present work. The similarity between the Ti-Cu system and the Fe-C system is evident and, as will be shown later, many of the transformation products appear to have similar microstructures. Heat treatments in this program were designed to produce the structures of primary interest for study and determination of mechanical properties. Experimental Procedures Preparation of Alloys: Five ½ lb ingots, ranging in composition from 0.8 to 6.83 pct Cu, were prepared by double arc melting in an atmosphere of high purity argon. Titanium melting stock was obtained from high purity iodide titanium, and copper additions were made from copper wire clippings. Segregation was reduced by inversion melting, in which the once-melted ingots were inverted in the crucible and remelted. The double-melted ingots were forged at 1600°F to ¾ in. diam rods, with both heating and forging operations being carried out in air. Surface scale was removed by grit blasting and grinding, after which the forgings were vacuum annealed at 900°C. The alloys then were swaged to ¾ in. diam rod at 750°C and test specimens were cut from this material. The vacuum annealing operation was to remove dissolved hydrogen, which is commonly present in the iodide titanium as-received. Although vacuum fusion analyses were not obtained for all these alloys, past experience indicates that the 6 hr treatment with a limiting pressure of 10- to 10-5 mm of Hg is sufficient to reduce the hydrogen level to 10 to 30 ppm. Vacuum fusion analysis of the 0.8 pct Cu alloy showed 19 ppm of hydrogen. In addition to the five hypoeutectoid alloys, three 15 g ingots were prepared with nominal copper additions of 9, 10, and 11 pct. Fabrication procedures were similar, except that these alloys were rolled to 0.040 in. sheet. Microstructure specimens only were obtained. Table I shows analyzed compositions and fabrication temperatures for these alloys. Heat Treatments: All heat treatments were made in potentiometer-controlled, resistance-wound tube

Jan 1, 1956

By J. L. Bruce, G. W. Nicolson

THE country rock of the Mavrovouni mine of the Cyprus Mines Corp. is hydrothermally altered, disintegrated pillow lava, with very little tensile strength ("short" ground). In places, especially when wet, it is heavy ground, though not extremely heavy except where movement has been caused by underlying or nearby stoping operations. Damage by caving from roof or sides of galleries is not sudden but progressively faster when the size of the cave increases as a result of the fall of small pieces. CEMENT AND CONCRETE LININGS During early operations, galleries in the country rock were supported by customary mine-timbering methods. Available timber, however, was of poor quality and of relatively high price, and replacements were frequent and expensive. Furthermore, the massive sulphide ore bodies required large volumes of fresh air for ventilation and cooling, and it was therefore desirable to provide smooth-lined galleries with low resistance for the introduction of air to the ore bodies. It was also desirable to eliminate hazards of fire in shafts and underground workings insofar as this would be practical. Cement and concrete were relatively cheap, and plans for using these in support of shafts, underground galleries, raises, and chutes, were developed steadily. Circular shafts with diameters ranging from 10 to 15 ft were adopted for all permanent shafts and airways. In places these were lined with concrete poured behind sectional pressed-steel forms especially constructed for this purpose. In other places, they were lined with precast-concrete blocks. It was found that such precast concrete of good quality could be produced on mass production scale and delivered at the mine from most favorable point of manufacture, at a cost of about 25 cents per cubic foot of concrete. This refers to prewar costs. As the use of concrete blocks in circular lined galleries was developed, it was found that there were very great advantages in the reduction of air resistance as compared with customary timber supports. After best methods had been developed, it was found that breakage and replacements were extraordinarily low, averaging only about 1 ½ pct per year during a period of about 15 years. Furthermore, it has been possible to reclaim for re-use a very large percentage of the concrete blocks from abandoned galleries. During the history of the operations precast-concrete blocks have been used for lining shafts, raises, ore chutes, galleries, and shaft stations, ranging from 3 to 16 ft id. The thickness of lining has varied from 5 to 10 in.; with I2 in. thickness in a few cases. Junctions of two galleries at angles ranging from about 30 to 60° are usually made of poured concrete behind sectional forms, or of a combination of poured concrete and precast blocks. In nearly all cases it has been found advisable to make the point of the wedge at the junction, of

Jan 1, 1947

By M. C. Dow

Belt conveyors generally are conceded to be the most economical method yet devised for the transportation of large quantities of bulk materials within plants. Belts are coming into greater use for transportation over long distances and are replacing other forms of long-haul conveyance. It is not the intent of the writer to comment on the design of belt conveyors, but to offer some suggestions for improvement in the operation of conveying belts, based on many years experience with belts in several stone-crushing plants. It is the contention of this writer that opportunities for improvement not fully realized by most operators exist in many plants and that a study of the individual conveyors can result in lower unit belt costs. General Reliability It is the fool-proof nature and general reliability of the belt conveyor that is responsible for its neglect. Even when abused, a belt will carry large tonnages and last a long time, often outlasting the personnel responsible for its care. Some operators look upon the purchase of a new belt as an expensive outlay every so many years, rather than a constant and steady cost amounting in belt wear alone to several dollars every operating day. This belt wear for all conveyors in one stone-crushing plant known by the writer costs 1 /12 cents per ton or $12 to $15 per hour, based on the present cost of belt replacements. The fact that these replacement costs are double those of prewar quality emphasizes the necessity of improving the conditions that make belts wear out. Some of those conditions are the responsibility of the conveyor designer, and if a serious original error has been made, this handicap cannot be overcome by the operator. If the belt is too narrow, too steep, or too fast for good loading, the operator finds that he has an inherently expensive belt. The other factors that decrease the life of a belt are more or less under his control. The two factors of most importance are the loading conditions and the alignment. Most of the cover wear and carcass cutting occurs at the loading point and if the alignment is not good under all conditions, edge wear or damage may result, Fig I. Loading the Belt It is difficult to load a belt in an ideal manner; that is, to flow the material on the moving belt at a steady rate, without impact, without turbulence, and with a velocity equal to and in the same direction as the belt. An inclined belt is especially difficult to load and particularly when its speed is over 300 or 350 fpm. Inclined conveyors require longer skirt plates to prevent spillage until the load settles. It does not seem reasonable to expect an inclined the to carry the same load as a horizontal belt of the same width and speed, because of the difficulty in loading

Jan 1, 1948

By M. C. Dow

Belt conveyors generally are conceded to be the most economical method yet devised for the transportation of large quantities of bulk materials within plants. Belts are coming into greater use for transportation over long distances and are replacing other forms of long-haul conveyance. It is not the intent of the writer to comment on the design of belt conveyors, but to offer some suggestions for improvement in the operation of conveying belts, based on many years experience with belts in several stone-crushing plants. It is the contention of this writer that opportunities for improvement not fully realized by most operators exist in many plants and that a study of the individual conveyors can result in lower unit belt costs. General Reliability It is the fool-proof nature and general reliability of the belt conveyor that is responsible for its neglect. Even when abused, a belt will carry large tonnages and last a long time, often outlasting the personnel responsible for its care. Some operators look upon the purchase of a new belt as an expensive outlay every so many years, rather than a constant and steady cost amounting in belt wear alone to several dollars every operating day. This belt wear for all conveyors in one stone-crushing plant known by the writer costs 1 /12 cents per ton or $12 to $15 per hour, based on the present cost of belt replacements. The fact that these replacement costs are double those of prewar quality emphasizes the necessity of improving the conditions that make belts wear out. Some of those conditions are the responsibility of the conveyor designer, and if a serious original error has been made, this handicap cannot be overcome by the operator. If the belt is too narrow, too steep, or too fast for good loading, the operator finds that he has an inherently expensive belt. The other factors that decrease the life of a belt are more or less under his control. The two factors of most importance are the loading conditions and the alignment. Most of the cover wear and carcass cutting occurs at the loading point and if the alignment is not good under all conditions, edge wear or damage may result, Fig I. Loading the Belt It is difficult to load a belt in an ideal manner; that is, to flow the material on the moving belt at a steady rate, without impact, without turbulence, and with a velocity equal to and in the same direction as the belt. An inclined belt is especially difficult to load and particularly when its speed is over 300 or 350 fpm. Inclined conveyors require longer skirt plates to prevent spillage until the load settles. It does not seem reasonable to expect an inclined the to carry the same load as a horizontal belt of the same width and speed, because of the difficulty in loading

Jan 1, 1948

By Samuel S. Adams

Potash, the generic term for a variety of potassium-bearing minerals, ores, and refined products (Table I), owes its importance as an industrial mineral to the potassium requirement of growing plants. The term "potash" originally referred to potassium carbonate produced by the leaching of wood ashes. This process, for which the first U.S. patent was issued in 1790, was the basis for the largest United States chemical industry in the early nineteenth century. The agricultural use of potash soon eclipsed the chemical applications following the German discovery in 1840 that potassium is essential to plant growth. The initial discoveries of large deposits of soluble potassium minerals, essential for agriculture applications, were made in 1857 in Germany and in 1914 in the United States. More than 90% of the 20.4 million short tons K2O produced in the world in 1970 (Eilertsen, 1971 ) was derived from marine evaporite deposits and approximately 90% was used in fertilizers. The potassium content of an ore, mineral, or product is customarily expressed as % K,O, a unit of measure which is neither a natural nor synthetic compound of potassium (1 .O% K is equivalent to 1.2046% K,O) . Geology Potassium, the seventh most abundant element in the earth's crust, is present in silicate minerals in igneous, sedimentary and meta- morphic rocks. Potassium is also a major constituent of many surface and subsurface brines (Table 2). Economic potash deposits are essentially restricted, however, to widespread, thick accumulations of marine chloride evaporite deposits. These deposits yield high grade, large tonnage ore bodies, many of which are amenable to low cost mining and beneficiation. The products from these deposits are, moreover, ideal for use in fertilizer because of the high relative solubility of the potassium chloride and sulfate evaporite minerals. World potash production and reserves for such de- posits so vastly overshadow other sources of potassium that the following discussion will be limited largely to potash deposits in marine evaporites with brief reference to certain potash-rich brines. Approximately 85% of current domestic production is from bedded salt deposits and much of the balance is from brines. Marine evaporite deposits are accumulations of salt minerals deposited in structural sedimentary basins through the evaporation of sea-water or mixtures of seawater and other brines. The salt minerals are precipitated in assemblages and sequences of assemblages as determined by the compositions of the brines and the solubility relations in the salt systems (D'Ans, 1933). The evaporation of seawater normally yields carbonate minerals as the first precipitates (Table 3). Further evaporation and concentration of the brine leads to the precipitation, in succession, of sulfate, chloride, and supersaline mineral assemblages including the salts of potassium and magnesium. The common minerals, ores, and products of potassium deposits are listed in [Table 1]. Many potash deposits contain accessory evaporite minerals together with a variety of detrital and authigenic silicates (Braitsch, 1971).

Jan 1, 1975

By T. E. Tietz, J. E. Dorn

Activation energies for creep of copper at intermediate temperatures, where crystal recovery was negligible, were determined by the simple technique of rapidly alternating the test temperature between and T2 (T2 = TI + about 10°K) throughout a constant stress creep test. The activation energy for creep H was found to be 37,000± 3,000 cal per mol, independent of stress and strain. The same creep laws as have been previously established for high temperature creep were found to be valid for creep at intermediate temperatures. But the AH was found to be lower than that for self-diffusion in the intermediate temperature range whereas it is known to be equal to that for self-diffusion at high temperatures. IT is now well established that creep at high temperatures can be correlated by the functional relationship'-" e = f(?) s = constant [I] where E is the total plastic strain, f is the function that depends on the stress, ? = f e -- dt, t is the duration of test, e is the base of natural logarithms, AH is the activation energy for creep, R is the gas constant,T is the absolute temperature, and s is the stress. Thus, identical values of are achieved during creep under a given stress at two alternate temperatures at the same total strain. At the same strain therefore where subscripts refer to the two alternate temperature conditions of test. Consequently, the activation energy for high temperature creep is readily obtained with the aid of Eq. 2. Activation energies so obtained have been observed to be insensitive to the creep strain at which they are evaluated, the applied stress, grain size, minor alloying additions,'-' cold worked state, and the presence of thermally stable dispersions of intermetallic compounds in an a solid solution matrix Furthermore, the activation energy for high temperature creep is very nearly equal to that for self-diffusion in all cases where adequate data are available for comparison." " The apparent identity of the activation energies for high temperature creep and self-diffusion strongly suggest that high temperature creep arises from a dislocation climb process. This hypothesis is further strengthened by the fact that the energy of activation for high temperature creep is insensitive to the applied stress," and by the observations that the correlation suggested by Eq. 1 cannot be ex- tended to temperatures below those for rapid crystal recovery. When using the activation energy for self-diffusion, Eq. 1 fails to give the required correlations between creep curves at various intermediate temperatures.' This suggests that the dislocation climb mechanism for creep might be superseded by some alternate mechanism in the intermediate range of temperatures. This investigation was initiated in a preliminary attempt to ascertain the type of creep law that might be valid in the intermediate range of temperatures. Special consideration, however, was given to the determination of the activation energy for creep in this range because the Becker-Orowan', " and the Mott-Nabarro10 theories for transient creep suggest that the activation energy should increase

Jan 1, 1957

By F. H. Deily, L. W. Ledgerwood, J. E. Eckel

A new method for drilling the earth's formations has undergone extensive laboratory and shallow earth drilling experimentation. This method, pellet impact drilling, uses the energy of a large mass of high velocity steel spheres to break and crush the rock. Pellets are confined to a region close to the hole bottom. Motive fluid for transporting and recycling the pellets is supplied by a modified jet pump. The pellet drilling method has inherent advantages over conventional rotary drilling. First, only a nominal amount of weight need be applied to the hole bottom. Second, only a very small amount of torque is required for bit rotation. Third, means are available for continual replacement of the cutter medium. The experimental laboratory work and analytical procedures necessary for the design of a pellet drill bit are described. In the laboratory program approximately half the effort was devoted to the development of a better understanding of the physical process, and half to the empirical testing of new bit configurations. Factors such as pellet size and velocity, jet pump characteristics and modifications, and power distribution are discussed. The design and construction of a pellet impact bit for drilling a 9 in. hole with 1 1/4 in. steel pellets are described. Drilling performance in representative rocks, hydraulic operating characteristics, and metallurgical problems are discussed. INTRODUCTION This paper discusses an attempt to reduce drilling costs through the development of a drilling method basically different from rotary drilling. Publications on drilling research indicate that the major effort on the part of manufacturers and operators has been confined to research in rotary, or rotary-percussion drilling. This applied drilling research has produced significant gains in drilling rates and bit life, but thus far it has failed to achieve any major decrease in general drilling costs. From recent statistics released by Drilling Contractors, it can be shown that the total cost of drilling an "average" well in 1953 was about 2 1/4 times the corresponding cost in 1935. Analysis of the costs will show that they are not due to inefficient field operations; they are due instead to both an inflated economy and greater "average" well depths. Diligent work by the industry has reduced the backlog of potential economic improvements in rotary drilling to a group of rather marginal prospects. Increasing depths and poorer quality reservoirs at these depths continue to make the drilling cost problem more acute. Hence, the aim of the work reported here was to develop a new drilling method not limited by the inherent characteristics of rotary drilling and thus capable of attaining further significant reductions in drilling costs. The effort devoted to research on this proposed new drilling method was of considerable magnitude and represented .in excess of 37 man-years of research. The affiliates of Standard Oil Co. (N. I.) sponsored this development program which was conducted by the Drilling Methods Section of the Carter Research Laboratory in Tulsa, Okla. The purpose of this paper is to

Jan 1, 1957

By J. E. Ostberg, G. Phragmen, A. Hultgren, S. Wohlfahrt

Detailed study was made of a number of rimming ingots, both low and high carbon, and especially upon effects of superimposed air pressure. Requirement to suppress core bubbles is between 10 and 15 atm; at 6.5 atm freezing was in semikilled manner and at 3 atm, steel was of rising type. Probable mechanism of freezing under various conditions is discussed. AN earlier paper' reported an investigation made by a committee for studying rimming steel ingots appointed by Jernkontorets in Stockholm. The present paper is the outcome of some further work done by the same committee. Since the characteristics of ordinary rimming steel are connected closely .with the amount of gas liberated during freezing and since this amount of gas is governed by the pressure, it was considered of interest to ascertain in what manner and to what extent definite pressures applied to the top of the liquid steel in the mold would affect the solidification process and the consequent structure of a rimming steel of ordinary composition. The experiments were made at the Domnarfvets Steel Works. The steel was made according to normal practice in a 4-ton Rennerfelt electric furnace. Ferromanganese was added in the furnace; no aluminum was added, with one exception. Analyses of the four heats are given in Table I. The top-poured ingots measured about 12 in. sq x 48 in. and weighed about 1300 lb. One or two ingots of each heat were allowed to solidify under pressure, using a special device for admitting compressed air to the upper closed part of the mold, as shown in Fig. 1. A heavy plate sealed with asbestos was bolted to the top of the mold. The plate had a tapered aperture for pouring. Immediately after pouring the hole was closed by a wedged plug, and compressed air was admitted through a hole in the plug. Because of some delay in applying the plug, full pressure was not reached immediately. The pressure was adjusted to the desired value as indicated by a manometer. In order that the interior of the ingot might have the benefit of the pressure, the freezing of the top crust was delayed by a refractory lining applied to the top part of the mold, Fig. 1. Ingots were also cast from each heat without applied pressure, and with and without refractory lining at the top. Axial sections of ingots were cut either of the whole ingot or of some part of it of special interest; sections were polished and usually etched.' To facilitate description of structures the following terms may be used for different types of ingots solidified under gas evolution: 1. Box-hat or boot-leg ingot: Abundant gas evolution during casting and during rimming; no rim holes. 2. Normal rimming ingot: Lively gas evolution during rimming; usually rim holes in lowest part of

Jan 1, 1952

By T. B. Counselman

PRobably the earliest concentration of iron ore in this country was carried on in the northeastern magnetite areas. Magnetic concentration was relatively simple and gave a concentrate that, after agglomeration, and in spite of beillg high in phosphorus hecause of the dry concentrating methods then in use, was satisfactory blast-furnace feed. Production from the northeastern magnetitc area languished after the discovery and development of the Lake Superior ores, where there was seemingly an unlimited tonnage of high-grade ore, first the Michigan ores, and subsequently the still larger deposits of Minnesota. For years only the higher grade, direct shipping ores of the Lake superior district were mined. Those of Michigan, and of the Vermilion Range in Minnesota, were hard ores and came principally from underground mines. The softer ores of the Mesabi came partly from underground mincs, but mostly from the enormous deposits that could be worked by open-pit methods. The costs of ore from these open-pit deposits, even with the high initial cost of stripping, were so low that the underground mines of the Mesabi could hardly compete. The so-called Old Range ores, of Michigan and of the Vermilion Range of Minnesota, were hard and lumpy, and opened UP the burden in the blast furnace, therefore making possible harder driving with greater output. Also, some of these Ores were of such grade and physical characteristics that they were suitable for charge ore in the open hearth. These ores, therefore, commanded a price premium. and could compete with the softer, finer, but cheaper, Mesabi ores. The big tonnage reserves, however, are on the Mesabi. and it is these big open-pit deposits that contitue- our stock pile of iron ore, from which we are drawing so heavily during this war period. On the western end of the Mesabi the ore was found to be high in silica, and not suitable as furnace feed. As early as 1902, attempts were made to concentrate this so-called wash ore and by 1910 the first washing plant was put into operation. The Process was very simple, consisting essentially of a sizing and washing operation, with scalping screens, logwashers and tables, which later were replaced by classificrs. Ore particles finer than I00 mesh were deliberately wasted, because these fines were undesirable in the furnace. Fortunately, these tailings were impounded, and already are being reworked. Before long some of the low-grade ores began to require more elaborate treatment than the simple washing operation and, tables having been discarded because of their low capacity, in favor of classifiers, jigs were next introduced. These were able to discard coarser pieces of tailing than classifiers. Jigs are in active use today, various improvements having been made in their design and application. Various other machines and methods of concentration have been tried from time to time, and have in turn been discarded for more improved processes., The latest and most important process that has been 38

Jan 1, 1944

By T. B. Counselman

PRobably the earliest concentration of iron ore in this country was carried on in the northeastern magnetite areas. Magnetic concentration was relatively simple and gave a concentrate that, after agglomeration, and in spite of beillg high in phosphorus hecause of the dry concentrating methods then in use, was satisfactory blast-furnace feed. Production from the northeastern magnetitc area languished after the discovery and development of the Lake Superior ores, where there was seemingly an unlimited tonnage of high-grade ore, first the Michigan ores, and subsequently the still larger deposits of Minnesota. For years only the higher grade, direct shipping ores of the Lake superior district were mined. Those of Michigan, and of the Vermilion Range in Minnesota, were hard ores and came principally from underground mines. The softer ores of the Mesabi came partly from underground mincs, but mostly from the enormous deposits that could be worked by open-pit methods. The costs of ore from these open-pit deposits, even with the high initial cost of stripping, were so low that the underground mines of the Mesabi could hardly compete. The so-called Old Range ores, of Michigan and of the Vermilion Range of Minnesota, were hard and lumpy, and opened UP the burden in the blast furnace, therefore making possible harder driving with greater output. Also, some of these Ores were of such grade and physical characteristics that they were suitable for charge ore in the open hearth. These ores, therefore, commanded a price premium. and could compete with the softer, finer, but cheaper, Mesabi ores. The big tonnage reserves, however, are on the Mesabi. and it is these big open-pit deposits that contitue- our stock pile of iron ore, from which we are drawing so heavily during this war period. On the western end of the Mesabi the ore was found to be high in silica, and not suitable as furnace feed. As early as 1902, attempts were made to concentrate this so-called wash ore and by 1910 the first washing plant was put into operation. The Process was very simple, consisting essentially of a sizing and washing operation, with scalping screens, logwashers and tables, which later were replaced by classificrs. Ore particles finer than I00 mesh were deliberately wasted, because these fines were undesirable in the furnace. Fortunately, these tailings were impounded, and already are being reworked. Before long some of the low-grade ores began to require more elaborate treatment than the simple washing operation and, tables having been discarded because of their low capacity, in favor of classifiers, jigs were next introduced. These were able to discard coarser pieces of tailing than classifiers. Jigs are in active use today, various improvements having been made in their design and application. Various other machines and methods of concentration have been tried from time to time, and have in turn been discarded for more improved processes., The latest and most important process that has been 38

Jan 1, 1944

By M. A. Steinberg, J. Wulff, R. Kamm

In a previous paper1 from this laboratory, the development of a lead grid method for exploring the distribution of strain and density within metal powder compacts was described. In that work thin lead foil with rectangular holes cut at regular intervals was inserted with the powder fill, the arrangement pressed and then radiographed to permit measurement of the deformation of the lead grid. Densities at each grid element obtained in this manner were plotted as a function of the die dimensions. From such plots it was found that the densest part of a compact pressed from one side (the top) is at the top outer region and the least dense at the bottom outer region of the specimen. The axial density maximum occurs more often nearer the bottom than at the top. As a result of such exploratory measurements, it appeared reasonable to conclude that variations in density could be attributed in the main to die wall friction. Thus compacts of large diameter appeared relatively uniform in density except where the die fill had been uneven. Finally it was found that lubrication of the finely finished die cavity contributed more to magnitude and uniformity of density within the compact than interparticle lubrication. Since publication of the above results, it was found that circular-hole grids could be more accurately made and, when deformed within the powder, more readily measured and analyzed. Much of the former work was repeated and new results which include the effect of lubrication, compact height, pressure, speed of pressing and vacuum pressing are reported in the present paper. Circular-hole Grids and Analyses OF Radiographs Commercial lead sheet 0.008 in. in thickness was used in all the work reported. The 0.0938-in. diam holes were punched in the sheet on 1/8-in. centers to an accuracy of 0.001 in. The finished grid used contained eight or more holes in a row and from I to 24 rows. The lead sheet was clamped between two pairs of brass strips bolted to a small milling machine table which was itself bolted to a bench in correct position near a vise which held the punch. Travel of the lead grid in two dimensions was controlled by two steel lead screws calibrated in 0.001-in. divisions. A stripper plate was used on the punch to avoid distortion of the lead foil. A high carbon-high chromium (chrocar) one-piece steel die was used throughout the work. The die cavity was 1.125 in. in diam and the clearance between plungers and die wall was 0.001 in. The die was also used for pressing from both ends with two long plungers. Finally, lapping of die and plungers gave a surface whose rms value On an Abbot profilometer was 5 micro-in. The die walls and plungers were, except where otherwise noted, lubricated with a stearic acid suspension in benzene. This was put on in multiple layers and allowed to dry before filling the die.

Jan 1, 1949

By N. A. Tiner

A study was made of the effects of temperature, type of loading, and electric polarization on the fracturing behavior of copper and zinc coated with mercury. Copper showed an em-brittlement only in cyclic loading, whereas zinc showed an em-brittlenzent in both static and cyclic loading. The embrittle-ment of zinc in static loading was prevented by sub-zero cooling to a temperatzcre of about -70°F. The emhrittlement of both metals was sliglztly reduced by cathodic polarization of mercury. The basic processes involved in fracturing were discussed in the light of these observations. When a solid metal is in contact with certain liquid metals possessing high wetting characteristics, a weakening effect is produced, and the solid metal fractures in brittle manner at a relatively low stress. This lowering of the fracture stress generally is considered different from the stress cracking caused by a corrosive liquid environment and is attributed to the lowering of the solid-liquid interface tension at the grain boundaries.1-4 The purpose of this paper is to describe a number of observations on the special features of fracturing of copper and zinc coated with a liquid mercury film, and to analyze the basic processes involved in fracturing in the light of these observations. EXPERIMENTAL OBSERVATIONS I) Effect of Type of Loading—The evidence appears to indicate that in static loading, metals usually fracture by the initiation of microcracks in the interior preferentially at the grain boundaries or at the intersection of slip bands.' In cyclic loading, cracks develop on the surface within the active slip zones, and gradually propagate with increasing num- ber of cycles.6'7 Because of this difference in the manner of initiation of cracks, a series of bare and mercury coated copper and zinc specimens was subjected to static and cyclic loading, and their fracturing behavior was examined. The specimens were machined to 0.25 in. in diam and 1 in. in length from a high-purity commercial bar stock, and annealed at an appropriate temperature. Mercury was applied to the surface of the specimens by rubbing with cotton wool soaked in a saturated solution of HgCl2 or by etching with a dilute solution of HC1 and rubbing with purified mercury and by washing in water. The static tension load-extension curves were obtained by means of a Riele Screw Power Universal Testing Machine. The room-temperature load-extension curves for copper and zinc are shown in Fig. 1. The deformation behavior of copper, as judged from the general configuration of the load-extension curve, was not affected by mercury coating. The maximum load to fracture and the elongation at the maximum load were practically the same for both specimens. The mercury coated copper, however, showed somewhat less localized necking and had smaller reduction of area than the uncoated metal. The behavior of mercury coated zinc was radically different from the behavior of uncoated metal. The load-extension curves were the same at the

Jan 1, 1962

By L. M. Barker, E. G. Lewis

THE literature of milling is replete with papers devoted to the subject of ball milling, all of which no doubt have contributed in one way or another to progress in that art. In this paper reference will be made to only a few of the many authors, but the value of the contributions of all who have written on that subject is hereby acknowledged. With a few exceptions the efforts of most students of the subject have been devoted to laboratory investigations of principles. Davis1 was one of the first to report on plant-scale investigations and to present to mill men certain criteria for the guidance of ball-milling practices. His conclusions with respect to the significance of sizing analyses of classifier sands in their relation to the factors of mill speed and ball sizing are particularly referred to. Those conclusions were: I. If the balls are large or the speed of the mill is high, crowding will appear at the finer sizes in the classifier sands. 2. If the balls are small or the speed is low, crowding will appear at the coarser sizes in the classifier sands. 3. The indications are that best efficiency is obtained when the screen analysis of the sands show a minimum crowding at any size. The last conclusion was qualified by the statement that it had not been proved conclusively. It is surprising, however, that the literature of later years reveals little evidence that millmen have made any serious attempt to apply those criteria. This may, perhaps, be explained by the fact that the average plant-scale ball-milling problem presents so many variables that an investigation of any one of them encounters the problem of control of the others-a problem that often is unsurmountable in a small plant. In a large plant, in which there is a duplication of grinding units in parallel operation, opportunity may be afforded for determining the value of such criteria. Nevertheless, a study of published data from grinding circuits of both large and small plants suggests that either Davis' criteria have been tried and found inapplicable or have never been given consideration. For the purpose of testing Davis' conclusions and with improvement of ball-milling efficiency as the final objective, a test program was initiated in the concentrator of the New Cornelia branch of the Phelps Dodge Corporation early in 1938. The practices of that plant have already been described .2 The fine-grinding units are arranged so that any one of eight units may be operated as a test unite and its results compared with those of the remaining units. All units receive similar feed from a common storage bin, in which the product of the fine-crushing plant is bedded by traveling tripper. The ball mills are all similar in size and operated at the same speeds, and are individually metered. The feeder conveyors of each unit are equipped with Merrick weightometers. The test program as initially outlined proposed investigation of the following:

Jan 1, 1941

By T. J. Woods

Tars paper deals with the origin, definition and prevention of scabs an semifinished rolled-steel product. Mold coatings, which are considered essential in scab prevention, were found to be effective only in relation to the ingot surface of semikilled and killed steels and not necessary for the rolled product. That is to say, the scabs on ingots caused by having been cast in uncoated molds are eliminated in the soaking and rolling operations, therefore are not present on the rolled product. This fact, which is contrary to the average opinion, was established after extensive and thorough experiments had proved the ordinary conception of the origin of scabs to be incorrect. This subject may be of little or no concern to steel plants producing small ingots for the manufacture of small billets and bars, except as it may be of interest in showing why their surface troubles with scabs do not exist on the product of heats with normal pouring practice. But to the producer of large ingots to be rolled into slabs for large plates used in shipbuilding, it is a very important subject. DEFINITION OF A SCAB The generally accepted opinion is that the individual scabs present on rolled products (as shown by Fig. I) are considered to have been individual splashes on the ingot surface. This opinion was found to be incorrect. Experiments showed that there were no individual scabs on the product that had appeared as individuals on the ingot surface. The single scabs seen are either pieces of a shell that is present near the bottom of all top-cast ingots, or a veneer that may be present on any part of an ingot improperly poured, as when the stream strikes the mold wall. This definition is based on a detailed study of scabs and their characteristics in which the following have been found true: Location.- On the product of heats poured without trouble, scabs, if present, are always on the product that corresponds to the bottom end of the ingot, and usually occur in clusters, This is true whether molds are coated or not. Shape.-There is no regularity as to shape, size or thickness. It is sometimes possible to separate a few pieces and place them together, like pieces of a jigsaw puzzle, indicating that at one time they had been united as one piece. If individual splashes were the origin of scabs, the foregoing would not be true. Instead, the splashes, which occur throughout the pouring of the ingots, would be present uniformly over the entire product and there would be considerable similarity in the shape and thickness of the scabs. EXPERIMENTAL WORK Our experimental work was conducted on 200-ton heats of semikilled plate steel tapped into an oval ladle 15 ft. high. All ingots were top-cast direct into 24 by 54 by 82-in. molds, straight-sided, set on fat stools. Two separate studies were made about one year apart, each study extending

Jan 1, 1943

By Nelson Severinghaus

FOLLOWING the end of hostilities of World War II, a resurgence of industrial and home building has given impetus to the use of many products of the stone industry. Shortage and high prices of some building materials such as lumber have aided wider acceptance of materials such as concrete products which have been relatively plentiful and which have not risen so rapidly in price. Ingredients for many of these substituting materials come from the stone industries, often from by-products of stone operations. Most of the tonnage of the stone industry in the State of Georgia comes from granite and marble. There are extensive dimension stone operations in granite in the Elberton and in the Lithonia areas. Building and monumental marble from the Tate area has been used throughout the country. Cutting operations in both types of stone have their by-products in faulty blocks and in spalls. In the State there are three large crushed-stone plants utilizing granite, one near Camak, one near Lithonia and one at Stockbridge. All have had excess fines or screenings in the past but this excess is largely disappearing with development of new uses. At times this "waste" has amounted to as much as 20 pct of the stone quarried. Handling of this large tonnage from point of screening out to storage piles presented a costly problem and large areas were taken up by the piles. Crushed stone is generally sold with a relatively narrow margin of price over cost, so any elimination of disposal cost or increase of income by marketing of by-products is highly desirable. BY-PRODUCTS OF GRANITE DIMENSION STONE It sometimes becomes difficult to differentiate between main product and by-product. In the cutting of granite dimension stone in the Lithonia district of Georgia, a considerable quantity of remnants of uneven shape and size is produced. The larger of these pieces have long found use as building rubble, particularly for retaining walls and building foundations (Fig I). They are broken down to one man size by plug drilling and wedging and by hammer. In recent times, demand for this former by-product has grown so that quarries have been opened for the production of rubble as a main product. Local masons have attained skill in using these irregular shapes to form economical and attractive walls. Areas such as Elberton, Georgia, which do not have a large building market nearby, tend to accumulate piles of large pieces of reject stone. When a road job or other local construction offers a quantity market for crushed stone, a portable crusher works this material down to crushed aggregate. Spalls and finer chips from granite stone-cutting operations have generally found their way into crushers and thence to the many uses for crushed aggregate. One company near Lithonia started marketing the smaller by-product crushed sizes for chicken grit about ten years ago. This use has grown to nation-wide distribution and the tonnage is now so great that they have opened a large quarry with

Jan 1, 1947

By Fred H. Poettmann, A. L. Benham

correlation of waters and identification of mixtures of two and three waters is important in secondary recovery evaluation studies and studies involving underground movement of waters. The importance of such studies suggests the need for a method to correlate a great number of water analyses to accurately identify and improve the understanding of mixtures of waters. Geochemical analyses of waters furnish a quantitative measure of each of the ions present in a water. Table L shows a portion of the data on many oilfield water analysis report forms in use today. Under "parts per million" are listed the quantitative amounts of each ion in milligrams per liter. Following the work of Stabler' and Palmer", some laboratories have reported additional data to indicate the reaction capacity, or reacting value of each ion. Table I lists data under two subheads for the "reacting value". Under the first subhead, the reacting value is reported in gram equivalents per million, hereinafter called equivalents per million. This value is determined by multiplying milligrams per liter of the ion by a factor equal to the reciprocal of the equivalent weight of the ion. Under the second subhead (per cent) is listed the percentage of each ion based on the total equivalents per million. Sodium is not usually an analyzed value in routine analyses, but is determined by the difference between total negative equivalent per million values and the sum of all of positive ion values for which analyses were made. This difference is reported as sodium, hereafter labelled "sodium". On this basis, the subtotals of the equivalent per million and per cent reacting values of the positive and negative ions are equal. CORRELATION OF WATER ANALYSES DATA Previously reported methods for correlating oilfield waters have used part of the data in Table 1, and can be classified into two categories. Correlation by Chemical Character Correlation methods using the chemical character of waters, as represented by the per cent reacting values of the ionic constituents, have been used by Palmer2 and Tickell. These methods have the limitation of neglecting the ionic concentration of the waters. This limitation can be serious in areas where waters have the same chemical character, but differ in concentration. Correlation by Concentration of the Ionic Constituents The Reistle' and the Stiff methods use the ionic concentration in parts per million and equivalents per million. These methods are effective in differentiating waters of similar chemical character and varying concentration, as in the highly saline waters of the Mid-Continent area. These methods have the disadvantage that they correlate waters by comparing many graphs of individual water analyses to determine the similarity to, or the variance from "type" waters. PROPOSED METHOD OF CORRELATING WATER ANALYSES DATA Correlation graphs presented in Fig. 1 represent water analyses data as points to facilitate the correlation of waters. The graph on the left of Fig. 1 is a plot of per cent reacting value of magnesium vs calcium. The right