Search Documents

By J. B. Campbell, V. V. Valleroy, B. T. Willman, L. W. Powers

A steam drive of heavy oil was field tested in a shallow, low oil-saturation formation near Deerfield, Mo. The pilot was conducted in the Warner formation, a sandstone containing an 18' API oil having 1,000-cp viscosity at the 60F origind reservoir temperature. The formation war at a depth of 160 ft. Steam was injected into nine input wells arranged in an array of inverted five-spot patterns. In the completely confined center pattern, 14 temperature observation wells were installed to obtain thermal data and observe test progress. Late in the test, slugs of ammonia were injected to trace the flow paths of injected fluids. From the test area about 7,000 bbl of oil were produced. Data were obtained on areal and vertical temperature distribution, steam front advance, reservoir fluid movement and terminal saturations. This field test of a steam drive (I) demonstrated the feasibility of the method, (2) confirmed that the low residual oil saturations observed in the laboratory are obtained in the steam-swept region in the field and (3) provided recovery and conformance data for one set of field conditions. INTRODUCTION The Deerfield steam drive pilot test was conducted in a shallow sandstone containing 1,000-cp oil. The venture was undertaken cooperatively by the research and production departments of Carter Oil Co., which organizations have since been consolidated into Esso Production Research Co. and Humble Oil & Refining Co.. respectively. The production department was interested in steam injection at Deerfield because it appeared to be the most promising method of commercially producing this heavy oil deposit. The research department was interested in applying the new recovery method and in evaluating its performance in the field. At the time the test was begun, the initial oil saturation was not well known. Subsequent air coring and early pilot results confirmed that there was too little oil in place for profitable commercial exploitation by steam. Pilot termination at that time, however, would have been premature for evaluating field performance of the process, and the tert was continued to obtain additional data on steam injection as a recovery method. The test was located in Vernon County, Mo., about 10 miles north of the town of Deerfield and only a few miles from the Kansas border. The pilot site was selected as typical of the area. The location represented neither the highest nor the lowest oil saturation region in the acreage under lease in 1954. The steam drive was conducted in the Warner sandstone of Lower Pennsylvanian age. At the test site the top of the Warner occurs at about 160 ft subsurface and the formation is a fine- to medium-grained micaceous sandstone that dips gently to the northwest at the rate of 12 to 15 ft/ mile. A cross-section and permeability profile of the test location are shown in Fig. 1. At the pilot location the average total thickness of the Warner formation is about 43 ft, but the effective thickness for steam drive is 26 ft. Two distinct types of hydrocarbon saturation are apparent. The lower portion of the total sand, averaging about 17 ft thick, contains a very heavy asphaltic material that will not flow under the influence of a steam drive. This bottom interval, referred to as a dead oil residue, was not considered as part of the net sand undergoing steam exploitation. The initial formation and fluid properties of the upper 26 ft in the test area are summarized in Table 1, and variation of oil viscosity with temperature is shown in Fig. 2. Imbibition tests on preserved core samples taken at the end of the pilot test showed that the Warner sandstone was then neutral or slightly water-wet. Initially, the reservoir may have been strongly water-wet as indicated by low relative permeability to water during both water injection testing and early steam injection. PRIOR HISTORY Initial production tests of wells at the pilot site produced water with only a faint show of oil. No gas was produced except at Well 7-W in the pilot area and at another well about 1/3 mile northeast of the pilot. Prior to the start of the steam drive, a two-well water injection test and a two-well air injection test were conducted. No oil was produced by either. Water was pumped into Well I-W in the northeast corner of the pilot area with simultaneous production from Well 1 (Fig. 3). The air-injection tat was run at input Well 9-W and its offset, Well 2, in the southwest corner. Air and water injectivities were about the same when corrected for viscosity and pressure differences.

By O. D. Sherby, J. E. Dorn

SEVERAL years ago Zener and Hollomon1 suggested that the flow stress of metals might be related to the temperature and strain rate in accord with the functional equation: s=s(eeh/rt) [1] at the same state. The Zener-Hollomon relation also contains the significant tacit implication that the energy for activation, AH, is substantially independent of the state of the material. The utility of this method for correlating creep data with tensile data was illustrated in a preliminary reportL on the effect of alloying additions on the secondary creep rates of binary a solid solutions in aluminum as shown for Al-Mg alloys in Fig. 1. Not only do the secondary creep and ultimate tensile properties for each alloy correlate well on this plot but in addition the activation energy, AH = 17,900 R cal per mol. is identical for the various compositions. Similar types of curves correlating the secondary creep rates at 422°K (300°F) with ultimate tensile data were also obtained for a series of dilute a solid solutions of copper, germanium, zinc, and silver in aluminum. In all cases the activation energy for creep, AH, was found to be equal to about 17,900 R cal per mol independent of the type of alloying element or its concentration. The coincidence of the activation energies for these alloys is probably due to the fact that the activation energies for creep are rather insensitive to small composition changes. Alloying additions, as shown in Fig. 1, however, increased the stress necessary to obtain equivalent values of ee?H/RT. Thus the stress level in curves of the type represented by Fig. 1 gives the relative creep strengths of the various alloys. Inasmuch as these correlations between creep and tensile data were obtained for creep tests at 422°K, it appeared advisable to ascertain the range of secondary creep rates and temperatures over which correlations between creep and tensile data could be made on the basis of the Zener-Hollomon relationship. If, for example, the activation energy changes with different ranges of creep temperatures, the utility of the proposed analysis would be severely weakened. But if AH is constant not only for all dilute alloys, but also over wide ranges of temperature and secondary creep rates, confidence will be developed not only in the broad utility of the Zener- Table I. Chemical Analysis':' and Grain Size of Alloys Mean Grain Residual Impurities. Wt Pct Diam- Alloying Atomic-eter, Element Pct Si Fe Cu Mg Mn mm Aluminum 99.987 0.003 0.003 0.006 0.001 0.25 Magnesium 1.617 0.003 0.004 0.006 0.26 Copper 0.101 0.003 0.003 0.0006 0.001 0.29 Zinc 1.616 0.003 0.005 0.007 0.001 '0.26 * The authors express their appreciation to the Aluminum Company of America for the preparation and chemical analyses of these alloys. Hollomon relationship, but also in its theoretical justification. The following investigation was instituted in order to ascertain the range of validity of the Zener-Hollomon relationship when it is applied to creep and tension data. Materials, Equipment, Technique In view of rather extensive correlatable data now available on the plastic properties of a series of binary a solid solutions of magnesium, copper, germanium, zinc, and silver in aluminum, these alloys were again selected for the present investigation. Previous reports have already covered the tensile properties of these alloys at subatmospheric temperatures," and at elevated temperature," as well as their fatigue properties at atmospheric temperatures, nd their creep properties at 422°K.' Resistivity measurementsa as well as precision lattice constant determinations? evealed that these alloys are a solid solutions. After homogenization. 0.100 in. thick sheets were rolled to 0.070 in. in thickness and recrystallized to about the same grain size. Since the details of these treatments were reported previously," they will not be repeated here. In order to appropriately reduce the scope of creep tests in this investigation only the typical alloys shown in Table I were investigated. All creep specimens were machined such that their tensile axes were in the rolling direction of the 0.070 in. sheet stock. The gage section was 2 in. long and 0.500 in. wide with a reduced section of 3.50 in. Creep strains were measured by means of rack and pinion type extensometers with a sensitivity of 0.005 in. per division. Readings were estimated to 1/10 of

Jan 1, 1953

By Wilhelm Borchers

IN all special branches of the chemical and metallurgical industries, in which large electric furnaces became necessary for carrying out new processes or for the improvement of old ones, the development of the electric furnaces took place on much the same lines. The endeavors to make a success of a new idea brought forth many ingenious designs, which, however, almost without exception, furnished the proof that the safest and shortest way to practical success is the utmost simplicity of construction of the necessary apparatus. Our knowledge of the qualities of materials for building electric furnaces and of the constituents of the furnace-charges, especially their electric conductivity and their chemical affinity . towards one another at high temperatures, is still far from being complete, and from this fact we must conclude that the smaller the number of elements in the construction of a furnace, the fewer the number of unreliable factors both in the construction and in the operation of the electric furnace. This conclusion deserves special attention when an electric furnace for making steel has to be chosen from the constantly growing number of inventions, inasmuch as the chief con¬stituent of steel, the element iron, is a substance which in its liquid phase has so great an affinity fir those elements which are to be removed from the charge, that it is very difficult to comply with the following conditions: 1, to beat the refining-slag to the highest point of its chemical activity ; to prevent the iron from entering the slaw, or, where this cannot be done, to make it enter so that it finally appears in the end-product

Jan 1, 1910

TO THE. BOARD OF DIRECTORS AND MEMBERS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS GENTLEMEN Submitted herewith are the report of the Treasurer for the year 1945 and reports for the same year of the following committees: Membership, Admissions, Papers and Publications, Mining and Metallury (Magazine), and Library. In this review of the year by the Secretary reference frequently will be made to the "Paul" Committee and to the "hotter" Committee. The first is the special committee on Divisional Relationships and the second the special Committee on Ways and Means. These two important committees, appointed by President Harvey S. Mudd under authorization of the Board of Directors on March 21, 1945, were composed as follows:

Jan 1, 1946

MR. Woo's succinct description of the mining and smelting of silver-lead in Mongolia, with the roasting-and-reduction process and cupellation, has much interest as a picture of methods that not only may have been in use, as he suggests, a thousand years ago, long before the existence of mining schools or chemical laboratories, but probably vary little, if at all, from the practice of prehistoric times, when King Priam's handsome silver vases, cups and bowls were formed. For it is highly improbable that such large objects were made from comparatively rare native silver, and the metal must have been smelted from ore, and most likely in great part from galena,, with cupellation of the lead. Dr. W. A. P. Martin, in his excellent book on the Lore of Cathay, points out that Chinese alchemy is over 2000 years old, antedating the European by at least six centuries; and he infers that the Chinese skill in metallurgy and many branches of practical chemistry owes its origin to " those early devotees of the experimental philosophy who passed their lives among the fumes of the alembic." Those alchemists, however, may have more likely derived some of their leading ideas from the mys terious, and at that time wholly unexplainable results observed in already very ancient metallurgical processes; in which, for example, certain stones were transmuted, as it were, into metals widely divergent in character from their ores, and even silver and gold were obtained from the most unlikely-looking mate rials. It is therefore, in any case, not improbable that the Chinese may have preceded western nations in the discovery of metallurgical methods. At all events, it is now evident that the Japanese acquired these arts from China, the former source of all their higher civilization. My own observation of old-fashioned silver-smelt ing at Hosokura, on the main island of Japan, and about 220

Jan 1, 1903

By David T. Day

IN 1897 I published a proposed explanation t for the variation in color and specific gravity of Pennsylvania oils. A resume of this subject was also presented at the First International Petroleum Congress, in Paris, in 1900. Since that time much experimental work bearing upon this explanation has been carried on by myself, in the United States Geological Survey, and under my direction, by Dr. J. Elliott Gilpin, Marshall P. Cram, and 0. E. Bransky, at the Johns Hopkins University. The experimental results thus accumulated seem to throw considerable additional light upon the variations in color and specific gravity of petroleum, as found in different parts of the world, and also upon the variations in chemical composition. Therefore, it seems as if a, summary of the evidence thus obtained might be of value to those members of the Institute who are interested in the examination of oil-fields. The summary is here presented for that purpose. The phenomenon has often been observed in many oil-fields that oils of different color, specific gravity, and chemical composition may be found within short distances of each other. A conspicuous example of this is the occurrence at Jennings, Welsh, and Anse la Butte, La., of petroleum chemically somewhat similar to Russian petroleum; that is, characterized by the presence of naphthenes. Another characteristic is the presence of considerable percentages of asphaltic compounds, sufficient in quantity to disguise the presence of solid paraffin wax, and perhaps also to render that paraffin wax more soluble * Published by permission of the Director of the United States Geological Survey. 1 Proceedings of the American Philosophical Society of Philadelphia, vol. xxxvi., No. 154, pp. 112 to 115 (January, 1897).

Jun 1, 1910

By H. C., Simpson

MANY metals by virtue of their place of occurrence as ore, and their uses are travelers! Iron and steel, for instance, is one of the greatest of travelers in the form of ships and the romance of iron in this respect is only just beginning to be superseded by the stories which can be told of the travels of aluminum and its alloys, used in the building of airplanes. Tin is a traveler from the Straits Settlements to this country and Europe, for use in the canning industry; afterward traveling all over the civilized world as a part of the container for preserved foods. Silver is somewhat of an aristocrat, when its uses are measured against those of the baser metals. From earliest times it has been used for adornment (first perhaps o4 the person and later for the embellishment of weapons and' buildings), for the making of fine ar¬ticles used in the household, and as money. While its uses have been widened by the discoveries in chemistry, electricity and other sciences, its early uses are still much in evidence in our modern life.

Jan 1, 1928

By M. W. BERNEWITZ

IT is 27 years since I last visited Broken Hill, New South Wales, one of the world's greatest lead-silver-zinc districts. Then, the flota¬tion of ores was in its infancy. The Minerals Separation process had its birth as a practicability in the Central Mill, which is still operating and yielding high recoveries. The average Australian knows that Broken Hill is an important mining center in a "corner" of New South Wales, but he does not know what a factor it is in the lead, silver, and zinc production of the world. Nor does he realize that among the ramifications arising from metal production at Broken Hill are the great lead smelter at Port Pirie, South Australia, 254 miles southeast; the electrolytic zinc works at Risdon, and the limestone mine at Davenport, Tasmania; the acid works at Cockle Creek, New

Jan 1, 1935

By Hiram B. Woon

Uranium ore deposits in the Lisbon Valley area are in an arcuate belt, 15 miles long by one-half-mile wide, on the southwest flank of the Lisbon Valley anticline. They range in size from 500 to 1,500,000 tons and by mid-1965 had yielded 6,147,000 tons containing 48,530,000 pounds of U3O8. Ore bodies average 6 feet thick, are tabular, amoeba-shaped masses, concordant to the bedding, and are in the thickest, lowest sandstone unit of the Moss Back Member of the Chinle Formation of Triassic age. The host rock is predominantly a fluviatile, calcareous, fine-grained to conglomeratic sandstone. Uraninite, the principal ore mineral, fills the pores in the sandstone and partly replaces sand grains and fossil wood fragments. During Late Permian and Early Triassic time pre-Chinle Formations were arched to form the ancestral Permian anticline. Moss Back streams truncated Moenkopi and Cutler beds which capped the ancestral anticline and then covered it with fluviatile elastics, which were subsequently covered by thousands of feet of Triassic, Jurassic, and Cretaceous sediments. Uranium, probably derived from the Chinle Formation by diagenetic processes, was transported in connate ground waters, was moved by compaction or hydrostatic forces, and was deposited under reducing conditions. Uranium was emplaced around the crest of the ancestral anticline, prior to the Laramide orogeny. During the orogeny, the Tertiary-Lisbon valley anticline was super induced on the Permian anticline and, penecontemporaneous with uplift, was faulted parallel to its longitudinal axis. The Big Indian ore belt on the southwest flank footwall block was elevated to approximately its present position, and the northeast flank hanging wall block was elevated only slightly. An extension of the Big Indian ore belt around the northeast flank of the ancestral Permian anticline may exist in the Moss Back sandstone in the downthrown block northeast of the Lisbon Valley fault.

Jan 1, 1968

By Max Hebgen

Within the State of Montana the streams rise in the high mountains at. an elevation of from 5,000 to 8,000 ft. These streams leave the State line both east and west at elevations from 3,500 to 2,400 ft. It is, therefore, apparent. that all these streams have an average fall of 3,000 ft. within the confines of the. State, and many opportunities are presented on all streams. for the development of power, by taking advantage of the natural fall. It is probable that 1,000,000 h. p. can :be developed in the State of Montana. I. NATURAL FEATURES OF STATE AFFECTING POWER DEVELOPMENT. The main. range of the Rocky mountains, forming the Continental Divide, cuts the State of Montana into two parts. The eastern part is drained by the Missouri river and its tributaries, the Madison; Jefferson, Gallatin and Yellowstone, rivers. The western part is drained by tributaries to the Columbia river, the Clarks fork and the Kootenai river. The Clarks fork in turn is formed by the junction of Missoula and Flathead rivers, the latter, draining Flathead lake. The western part of the State. is mountainous and the eastern part is comparatively level. As a natural result the rivers in the western part are capable of generating large amounts of power, while in the eastern part of the State natural power sites are much fewer and farther apart. It also follows that in the mountainous districts large amounts of power are required for the mining industry, while in the eastern part of the State, which is principally devoted to agriculture, power is required in smaller quantities. ?

Jan 8, 1913

By Herty, C. H.

Present-day interest in the question of "dirty steel" has arisen primarily from the increasingly rigid specifications on various grades of steel and from the growing conviction that non-metallic inclusions are the source of many of the difficulties in meeting these specifications. The importance of inclusions has unquestionably been over-emphasized in many cases, but on the other hand many unpublished instances could be recorded where all evidence pointed to inclusions as the primary cause for the failure of steel in rolling or in service. The solution of the problem of dirty steel is not a matter of a few years. There are almost numberless types of inclusions. They segregate in steel ingots in an entirely different manner from other impurities, and, at best, only a start has been made in developing correct analytical methods for their determination. Most of the writers in the field have expressed opinions rather than given facts, and so many variables enter into the manufacture of steel that a study of plant conditions is difficult unless definite facts on certain phases of the inclusion problem are available. This statement is not intended to convey the idea that little work has been done on this problem. On the other hand, the number of investigations has been large, but in most cases too many variables have been present to allow definite conclusions to be drawn. In the body of the text, reference to previous investigations is made at suitable points. Rather than burden the reader with a lengthy review of the literature on the general subject of inclusions, reference to the particular works pertinent to the subject matter of the bulletin has been discussed. Three excellent bibliographies b on the subject have been lately published: one by the Committee on

Jan 1, 1957

By Willard L. Cumings, Benjamin L. Miller

(Glen Summit Meeting, June, 1911.) I. THE CAMAGUEY DEPOSITS. 1. Location. THE Camaguey brown iron-ore deposit covers the top of San Felipe hill, the nearest point of which lies 14 miles NW. of the city of Camaguey. While there are several low flat-topped hills in the vicinity covered with a more or less continuous mantle of brown iron-ore, the deposit of San Felipe hill is the only one of any size and importance, and the name "San Felipe district " is proposed for the region. The deposit extends in a NW-SE. direction for a distance of about 10 miles, with an average width of 5 miles. The location is shown in Fig. 1, a sketch-map of the eastern part of Cuba. Fig. 2 is a map of the San Felipe district. 2. Description. The district is mentioned by Spencer,1 who says: "The Cubitas iron-ore fields are situated from 12 to 15 miles north of Camaguey City, in the province of Camaguey Within an area measuring roughly 10 miles east and west and 4 miles north and south, there are several flat-topped mesas rising 300 to 400 ft. above the level of an almost featureless plain which extends for many miles in all directions except toward the north." With the exception of the discrepancy in his statements as to the distance from Camaguey and the area of the hill, which is over 50 sq. miles, his description is a very good one. Kemp 2 has the following to say of ores in Carnaguey Province * Geologist, Bethlehem Steel Co. + Professor of Geology, Lehigh University. 1 Bulletin No. 540, U. S. Geological Survey, p. 324 (1908). 2 The Iron Ore Resources of the World, printed by the Eleventh International Geological Congress, vol. ii., p. 795 (1910).

Mar 1, 1911

By W. H. Caruthers

ECONOMIC utilization of all by-products has long been the goal of American industry. One of the first groups that was popularly supposed to have achieved its aim was the meat-packing industry, which reputedly found a use for everything except the squeal of the hog. To the metallurgist, slag has always been the principal wasted by-product, representing a loss not only of material, but of heat. Slag does not possess many qualities that appeal to man's imagination or suggest a romantic influence on the daily life and progress of a community or nation. It is a bulky product, and space for its disposal within reasonable hauling distance of a smelter is not always available; the iron-ore smelter especially has been wont to find space for slag disposal at a premium. Therefore, the success that has been attained in recent years in finding a use for iron blast-furnace slag is notable. It has become a vital economic factor in the construction industry in areas where it is available. Its use may suggest further possibilities of an economic outlet for the slags from nonferrous smelting as well.

Jan 1, 1940

President-Mrs Andrew E Beer, Richardson Ave, Sea Cliff, L I, N Y First Vice-President-Mrs Lyman H Hart, 6-F Essex House, Garth Woods Apts, Scarsdale, N Y Second Vice-President-Mrs John R C Mann, 90 Edgemont Road, Scarsdale, N Y Third Vice-President-Mrs Edward P Chapman, Jr, 2632 Vista Larga Dr N E, Albuquerque, N M Fourth Vice-President-Mrs R A Cattell, 7717 14th St, N W Washington 12, D C

Jan 1, 1959

By CHARLES DORRANGE

INTRODUCTION. CULM is a general term used in the anthracite regions for many years to denote a mixture of coal, bony coal and impurities which is sent to the refuse-banks. Thus, 35 years ago culm contained the pea and buckwheat sizes of anthracite; but to-day, and as mentioned in this paper, culm is used specifically to denote the material which passes through the smallest screen in the anthracite-breaker. The smallest size of commercial anthracite is known as No. 3 buckwheat, barley, or bird's-eye coal, and is ordinarily made through a round-punched plate having openings 3/16 in. in diameter, and over a round-punched plate with opening 3/32 in. or 1/16 in. in diameter. Thus culm will consist of coal, bony coal, slate, gravel, iron pyrite, etc., ranging in size from ? 3/32 in. down to dust. Other local terms for culm are " slush," " silt," and " dirt." The first experiments towards the utilization of anthracite culm by briquetting, and the first briquetting-work done in this country, were in 1872 at Port Richmond Piers, Philadelphia, Pa., by E. F., Loiseau.1 Clay was used as a binder and the finished briquette was water-proofed with shellac, etc. Excessive cost was given as the reason for discontinuing work at this plant. The Delaware k Hudson Co., in 1876, built a plant at Rondout, N. Y., which operated until 1880. Gas-tar was used as a binder, and anthracite screenings were briquetted for engine fuel. Excessive cost, poor results in firing, and the tendency of the fuel to cut the boiler-flues were given as the reasons for discontinuing the manufacture. The next plant was built by E. F. Loiseau about 1878, at Nesquehoning, Pa., near the No. 1 or Nesquehoning colliery

Sep 1, 1911

By Y. C. Liu, G. A. Alers

The anisotropy of Young's modules has been measured in a series of Cu-Zn alloys containing from 1 to 28 wt pct Zn and cold-rolled to 97.5 pct reduction in thickness. These modulus data show a transition in texture as a function of zinc content. In alloys containing 3 pct Zn or less, the texture is essentially that of copper. A transition is clearly seen to develop in 5 and 8 pct Zn alloys, and to have been completed in a 12 pct Zn alloy. Increasing the proportion of zinc to 28 pct does not produce any further changes in texture. The ease and clarity with which this texture transition can be seen in the modulus data is in great contrast with the inccertainty in the visual detertiination of the range of texture transition from a series of pole figures. It is also shown that the rolling texture of the high zinc content alloys cannot be a one-COIIIponenl texture, characterized by the (110)(112) ideal orientations, as usually assumed. A second, quite important component must also be present. Furthermore, the present data are inconsistent with matrix orientations on which the "oriented growth" hypothesis of the Formation of recrystallization textures is based. THE rolling textures of binary fcc alloy systems have generally been considered to lie between two terminal textures. One of these terminal textures is the copper type and the other is the 70:30 brass type. Alloys of intermediate solute content exhibit a texture which is said to be a transition between the two terminal textures. On the basis of efforts to correlate rolling and recrystallization textures, two concepts have been advanced in the literature on the nature of these transition textures. One school1 suggests that the addition of alloying elements, e.g., zinc, causes a gradual rotation about one of the (111) poles from the (358)( 523) ideal orientation of the copper-type rolling texture to the terminal {1 10)( 112) ideal orientation used to describe the rolling texture of 70:30 brass. This concept is depicted in Fig. 1 with the angle of rotation corresponding approximately to the zinc content and is designated here as the "rotational concept", since the ideal orientation of the transition textures varies continuously with alloy content. The other concept,' the "mixture concept", suggests that the copper-type rolling texture is a two-component texture. {358) (523) and {110)(112). The addition of alloying elements affects only quantitatively the relative amounts of these two components—a decrease in the amount of material in the {385}(523) orientation and an increase of that in the {110)(112) orientation with increasing solute content. An experimental distinction between these two concepts is essential to a better understanding of both the mechanism of formation of rolling textures and the subsequent formation of recrystailization textures in fcc metals. Because of the lack of resolution inherent in pole figures, it has not been possible to differentiate between the two concepts on the basis of this data. Both concepts, in fact, make use of the same set of pole figures but interpret them in a manner acco-rding to the view held.'" Experimental results obtained from inverse pole figures or selected-area electron diffraction3j4 simply -yield more refined pole figures but do not eliminate the ambiguity of interpretation. Quantitative measurement of an entirely different, orientation-dependent property must thus be considered

Jan 1, 1967

By Charles Albert Ashburner

The coal-fields of the United States have been variously classified as to their geographical positions. In 1887 I proposed slight changes to the classification generally used, for more convenient description of our coal-fields in my report on the statistical history of coal in the States during 1886 for the United States Geological Survey. This new classification seems to meet all practical requirements and has been generally adopted. The coal-areas are grouped in two divisions—the anthracite division and the bituminous division. The anthracite division, in a commercial sense, may be said to include the anthracite districts of Pennsylvania alone, although small amounts of anthracite are mined in Colorado and have been

Jan 1, 1890

By Dunbar D. Scott

The development in the perfection of mine-surveying instruments has been by no means rapid, as it has depended somewhat on the details of construction borrowed from astronomical and geodetic theodolites, largely on the restrictions laid down by mining companies and the prejudices of mine managers themselves, but more than all on the methods used in conducting surveys and the importance attached thereto. Mine-surveying, in some form or other, has been practiced from the very earliest times; but it has never kept pace with the other branches of surveying, or even with the art of mining itself, and cannot be recognized as an exact science until shortly before the beginning of this century. The works of Hero of Alexandria, who lived in the second century B.C., are still extant, and contain descriptions of a rectangular sighting-instrument, which he invented and called a diopter. His improvement upon this simple construction, which possibly he devised for use in the Greek mines for rough leveling-purposes and for laying out any angle, must be considered, says Hübner," as the origin of the highly perfected theodolite of to-day. Whether this instrument came into general use during the first centuries of the Christian era, is not recorded; in fact, no writer undertakes to tell how mine-surveying was conducted until 1556, in which year Agricola expounds the principles of mining and metallurgy in his De Re Metallica, devoting the entire fifth chapter to the practice of mine-surveying (see Fig. 1). In mediæval times those who possessed any knowledge of engineering skill made strenuous effort to keep their art a secret, partly on account of the miners' proverbial conservatism and partly for their own personal aggrandizement, and were, in

Jan 1, 1899

By M. E. Grimes

A method of predicting uranium extraction rate in underground bacterial leaching of as-blasted ore has been developed. The method is based on the hypothesis that extraction is directly proportional to the volume of a piece of ore that is penetrated by the leaching agent, and that each piece of ore, regardless of size, has been penetrated radially from the external surface to the same depth at a given leaching time. Consequently, given an initial size and assay distribution, extraction should be predictable for a given penetration. Two laboratory bacterial leaching tests under simulated stope leaching conditions were carried out for a periods of 89 and 96 weeks. On completion, the residual ore was screened and analyzed. The information so obtained was employed to provide an elapsed time base for the penetration model, from which predictions of future extraction were made. The finding of solubilized uranium trapped within apparently sol id ore pieces was unexpected. However, it is not recoverable except after crushing, and hence does not affect calculations of underground leaching .

Jan 1, 1974

By Zay Jeffries

From the title of this chapter the reader could expect an attempt to outline the anticipated shape of things to come, mineralwise. We have no crystal ball and if we possessed one we could claim no expertness in its use. In the first place no one can tell the future status of man. No one has any way of knowing to what extent peace will prevail, nor to what extent changes may occur in national sovereignties or forms of government or in international relationships. So future man is an uncertainty. Nor can we predict new developments that may result in significant changes in man's status or in the mineral industry or both. If, for example, this chapter had been written in the middle 1930's, nearly everything that has happened since in the field of atomic energy would have been missed. Yet what a vast change this has made in the status of man! Also the changes in the mineral industry have been important. A writer would have been bold indeed had he prophesied that uranium would play such an important role. But we need not confine our foggy vision to the atomic energy field. The steep rise in the use of aluminum, titanium, and germanium reflects the unpredictable in what may be thought of as the more normal pursuits. This should not discourage one from using the past and currently observable trends as bases for limited predictions. To do this, however, it is desirable to make certain assumptions about man's status without even a pretense that these assumptions have a high probability of fulfillment: 1. Only minor changes will occur in the geographical boundaries of the nations of the world. 2. World War III will not take place in the near future. 3. As a consequence of (2), man will not destroy himself by wanton use of atomic weapons. 4. Disarmament will take place, if at all, gradually rather than all at one time. Under the above assumptions the world will enjoy a period of relative peace even though the status may be one of an armed truce. The assump-

Jan 1, 1959