Search Documents

By V. Koump, T. F. Perzak, R. H. Tien

A series of experiments were carried out in which the rates of propagation of the liquidus and the eutectic fronts Mere measured during essentially one-dimensional freezing of Al-Cu alloys. The dimensions of the ingots were 3 by 5 by 6 in. Three different alloys containing 0.1, 4.5, and 17 pct Cu were used in these experitments. For each alloy the rate of heat removal was varied to give a total jreezing time in the range 3 to 30 min. The results of these measurements cowlpared favorably with the theoretical model of freezing of binary alloys with time-dependent surface temperature. IN engineering analysis of solidification of commercia1 steels and nonferrous alloys it is a common practice to assume that an alloy freezes by propagation of an isothermal solidification front, i.e., essentially as a pure metal. In two recent theoretical investigations'j2 the present authors explored the possibility of a more realistic approach to the problem of solidification of alloys. In the proposed model the freezing of an alloy is assumed to take place by propagation of two isothermal fronts, i.e., the liquidus front and the solidus (or eutectic) front. The region between the two fronts contains both liquid and solid and is referred to as the solid-liquid region. The width and the solid content of the solid-liquid region vary with alloy type, solute concentration, and cooling rate. For a given alloy system, initial concentration of solute, and the mode of heat removal, the proposed model yields the temperature distribution within the solid skin, temperature, solid fraction, and concentration distributions with the solid-liquid region, and the rates of propagation of the liquidus and the solidus fronts. This model is obviously of considerable practical importance in engineering analysis of solidification processes, since it gives a more realistic estimate of skin strength during solidification and a better estimate of the total freezing time. Before the new model can be used with confidence, however, it is necessary to test this model experimentally. The experimental testing of the proposed model is a relatively simple matter since the effects to be measured are large and a relatively simple experiment will suffice. The theoretical model predicts, for example, that during freezing of an alloy containing substitutional type solute (negligible diffusion in the solid during freezing) the solid-liquid region occupies an appreciable portion of the ingot, even at low concentration of solute.' Another prediction of the theo- V. KOUMP, formerly with U. S. Steel Corp., is now with Research and Development Center, Systems and Process Division, Westinghouse Electric Corp., Pittsburgh, Pa. R. H. TlEN is Senior Scientist, Fundamental Research Laboratory, U. S. Steel Corp., Research Center, Monroe ville, Pa. T. F. PERZAK, formerly with U.S. Steel Corp., is now with Fiber Industries, Greenville, S. C. Manuscript submitted March 6, 1968. IMD retical model, easily verifiable by experiment, is that the rate of propagation of the solidus (or eutectic) front increases as the solidus front approaches the center of the slab. This prediction is contrary to well-known behavior of the solidification front during freezing of pure metals, where the rate of propagation of the solidification front decreases with time and freezing is completed at the lowest rate. A rather severe test of the proposed model is provided by comparison of theoretical predictions and experimental measurements of the effects of cooling rate and composition on the rates of propagation of the liquidus and the eutectic fronts. In order to test the soundness of the formulation and the method of solution of the problem of solidification of alloys a series of experiments were carried out in which the rates of propagation of the liquidus and the eutectic fronts were measured during essentially one-dimensional solidification of A1-Cu alloys. The A1-Cu system was chosen strictly as a matter of convenience. Three different alloys containing 0.1, 4.5, and 17 pct Cu were used in these experiments. For each alloy the rate of heat removal was varied to give the total freezing time in the range 3 to 30 min. The results of these measurements are compared with the predictions of the theoretical model of solidification of binary alloys, with time-dependent surface temperature.' Before the experiments described in this paper were undertaken, a serious attempt was made to utilize the measurements of previous investigators to test the theoretical model. In the course of this preliminary study a careful review was made of experiments of Pellini and coworkers3 and Doherty and Melf~rd.~ The measurements in Pellini's work were carried out using a steel containing at least four major components. Evaluation of the solid fraction-temperature relation for this steel (required in the theoretical model) is difficult and uncertain. Doherty and Melford, on the other hand, measured the solid fraction-temperature relation experimentally, but did not give sufficient data to explore the effects of composition and the cooling rates on solidification. Hence it was not possible to utilize these measurements to test our theoretical model. EXPERIMENTAL METHOD The experimental technique used in this investigation differs somewhat from the more conventional techniques employed in solidification studies. This technique was developed primarily to eliminate con-vective mixing in the molten metal caused by pouring of molten metal into the mold. In our experiments A1-Cu alloys were melted directly in the mold. The mold assembly used in solidification experiments is shown in Fig. 1. The mold was fabricated from *-in. stainless-steel sheet. The dimensions of

Jan 1, 1969

By J. Walter Snavely

PRESENT-DAY processing in many industries, calcining, sintering, briquetting, beneficiation and nodulizing, increasingly calls for the handling of large volumes of hot bulk materials. Various types of conveyors have been employed. This discussion will cover the factors governing their selection. For temperature ranges up to 400°F, or approximately 200 °C, a wide range of conveyors is available. Special constructions of rubber conveyor belts, steel conveyor belts, vibrating and shaker conveyors, apron conveyors, and drag chain conveyors, all are used successfully. As temperatures go well above 400 2F, however, choice of conveyors is narrowly limited. This paper will consider the problem of handling bulk materials only where the temperatures exceed 400°F. The arbitrary selection of 400 °F as a dividing point undoubtedly can be challenged, as special conveyor belting constructions are available which are suitable for temperatures in excess of 400°F. However, when the relatively short life of such belts and the cost of their replacement, with the attendant down time, are balanced against the reliability and long service life of the properly designed steel constructed units to be discussed, there is little question in any operator's mind that the special belts are more expensive to use. Because the conveyors under study are for the handling of bulk materials, inevitably including a high proportion of fines, obviously wire mesh belts cannot be included for consideration. Even though this type of conveyor is widely used at high temperatures, i.e., for carrying glassware through a lehr, it is unsuited for the conveying of bulk materials, and therefore will be excluded from further discussion in this paper. Preliminary to the study of the conveyor itself is the determination as to whether the material is to be cooled while it is being handled, or whether the processing requires retention of all heat and the maintenance of a given temperature range. In the majority of cases cooling is incidental to or part of the handling process, when the handling, for example, follows completion of sintering, roasting, calcining, refining, or some other process. To meet such operating conditions successfully, the conveying medium used must have: 1—a construction capable of withstanding maximum initial temperatures of the material being handled. 2—a construction providing efficient heat transfer for cooling. 3—a construction providing dependable operation and long life with minimum service requirements, and 4—a construction providing controlled and efficient conveying. Under the usual conditions of cooling during the handling, the construction selected to withstand the initial maximum temperatures does not necessarily involve using alloys, as excellent results can be achieved with normal carbon steels and cast irons, when they are properly applied and proportioned. The earliest and simplest type of conveyor for handling very hot materials is the cast steel drag chain conveyor, still widely used for handling hot cement clinker, as illustrated by Figs. I and 2. Because of the rugged and generous proportions of the chain link design, low carbon steels are entirely suitable for the links. The pins, however, must be alloy steel. The simple, rugged construction of this type of conveyor makes it readily capable of withstanding high initial temperatures, even though the chain is operating buried in the material. The drag-chain type of conveyor has advantages and limitations. Although the efficiency of the heat transfer is relatively poor, the life of the conveyor is reasonably long, and because of its crude simplicity it does not require much servicing. However, as a conveyor, it is limited in capacity, and largely limited to horizontal runs. Furthermore, because of the crude design, heavy weight, and the chain operating at the temperature of the material, greatly reducing permissible operating chain pulls, this type of conveyor is limited to relatively short centers. Another type of conveyor that has been used for very hot materials is the cast pan conveyor. Because of its very generous proportions the cast pan, which is made of either cast iron or malleable iron, can withstand initial maximum temperatures. It also provides efficient heat transfer for cooling. Further, it is on efficient conveyor construction, which can be used for inclines. Because the chain employs rolling friction instead of sliding friction, and is not in the maximum temperature zone, much longer centers are possible. It is this type of conveyor that is frequently used in the casting of various metal pigs, pig iron, and aluminum; it is obvious, therefore, that very high initial temperatures are being handled. With this kind of conveyor the return run is frequently sprayed with water to accelerate heat transfer. The build-up of residual heat in the very heavy cast pans is thus overcome. The outboard roller steel pan conveyor is an improved pan conveyor' which provides high rates of heat transfer and substitutes formed steel pans for the heavy cast pans. It is a very efficient conveying medium. The details of this particular construction are clearly shown in Fig. 3. An early application of this type of conveyor is shown in Fig. 4. In this case the conveyor units are handling roasted phosphate rock at average temperatures of 1000" to 1500°F, and frequent maximum temperatures as high as 1900°F. Several widths are used. The capacity of the unit at a speed of 50 fpm is approximately 30 tph per inch of width at peak loadings, average capacity being about 1/3 of peak loading. The assembled conveyor is shown in Fig. 5, with views of both the top and the underside to show all the construction details. In particular, the following general design principles were carried out in this construction:

Jan 1, 1954

By A. J. Mortlock

Cobalt and nickel have been diffused at tracer concentrations in gold at several temperatures in the range from approximately 700° to 950°C. The diffusion penetration profiles were determined by a serial sectioning technique in which the gold is first anodized and then the anodic layer is dissolved in acid. In this ulay sections as thin as 250A could be removed reproduci-bly. In all cases, the region close to the specimen surface was characterized by irregular behavior in the sense that the logarithm of concentration was not linear in the square of the penetration distance. In sotne cases, there zuas an indication of the operation of very slow dijfusion in this region, while in others the apparent diffusion coejj'icient was negative. Possible reasons for this anomalous behavior are briefly discussed. In recent years it has been found that the region close to the surface of a metal can sometimes exhibit anomalously slow diffusion characteristics relative to the interior of the metal. One of the best examples of this fact is the work of Styris and omizuka,' who showed that the apparent diffusion coefficient for zinc in the region withi: about 1 p of the free surface of copper was about ,,,, that at deeper penetrations. This result is particularly interesting, because it is free from the possibly complicating effects of low solubility of the diffusing tracer in the solvent metal. In the case of diffusion under conditions of low solubilitjr, interpretaticn of the results in terms of lattice diffusion is difficult because of the enhanced short-circuiting produced by segregation to dislocations.2'3 Measurements by Duhl et 1. suggest that cobalt diffusing in gold may also show a near-surface effect of this type. Once again the solubility is high, so that this result could be of great interest. However, the technique used for analyzing the diffusion penetration zones by Duhl, viz. the counting of residual gamma activity in the specimen following sectioning, appears to have indicated a near-surface effect in a parallel experiment on the self-diffusion of gold reported at the same time. The latter result is known to be spurious, since Kidson5 has demonstrated that self-diffusion in gold does not show this effect. Duhl et 01. also reported some measurements on the diffusion of nickel in gold, but failed to give any data for the near-surface region. As the solubility of nickel in gold is high, such data would also be of special interest. We, therefore, decided to conduct another set of experiments on the diffusion of nickel and cobalt in gold, using a sectioning technique that allows the individual sections to be assayed for solute content and thus gives direct determinations of penetration profiles. Also, by sectioning with an anodizing/stripping tech- nique, very thin layers can be removed and the region close to the surface studied in detail. MATERIALS The gold specimens were supplied as single crystal disks $ in. in diam by a in. high by Monocrystals Co. of Cleveland, Ohio. The gold itself was of spectro-scopic purity, i.e., better than 99.99 pct pure. METHOD Specimen Preparation. One flat end face of each gold crystal was spark planed with a Servomet spark erosion machine set for minimum spark energy. Following this treatment the crystals were preannealed for 2 to 4 days at temperatures of either 400" or 700°C. The three crystals preannealed at 700°C showed signs of recrystallization. The spark-planed end face of each crystal was then coated with the appropriate amount of 63i or 60 radioactive tracer. This deposit was laid down in a simple plating bath containing the as-supplied solution of the radioactive isotope as well as sufficient ammonium oxalate to saturate the solution. Some ammonium oxalate remained undissolved on the floor of the bath for this purpose. During plating further additions of ammonium oxalate were sometimes required to allow the plating to continue satisfactorily, perhaps due to passivation of the undissolved oxalate already present. The thickness of the deposited layer was determined by comparison of the apparent surface activity of the plated specimen with that of a similar specimen having a weighable deposit of the isotope on its end face. Correction for self-absorption of the radiation was made in this calculation. Annealing. The deposited crystals were annealed in a hydrogen atmosphere in sealed silica tubes. During this heat treatment they were supported, active face down, on optically flat silica plates. The temperature was measured with calibrated Pt vs Pt-10 pct Rh thermocouples, and the tabulated values can be taken to be correct to Z°C. All the crystals showed evidence of recrystallization following these heat treatments, suggesting that initially they may not have been good single crystals or had suffered strain during delivery. Concentration Profile Analysis. After annealing, the crystals were sectioned by the anodizing-stripping technique.6 The anodizing involved suspension of the specimen with its cylindrical axis horiz6ntal by a gold wire in a 200-ml beaker containing 1 M Hg304. A cathode in the form of a strip of gold sheet, 2 in. wide and positioned to be in contact with the curved side of the beaker, completely encircled the specimen. An anodizing current of 30 ma, corresponding to a current density of 5 ma per sq cm on the surface of the specimen, was passed for times ranging from 5 to 150 min depending on the thickness of gold to be removed; the solution was stirred continuously during this process. Following this treatment, the specimen

Jan 1, 1969

By J. Szekely, P. Tarassoff, N. J. Themelis

In a copper converter air enters the bath in the form of turbulent jets. The interaction of these jets with the molten matte is fundamental to the converting process. In the present study, an equation is derived to describe the trajectory of a gas jet in a liquid. Calculated and experimental results for air jets injected into water are in good agreement. The trajectories of air jets in copper matte are predicted. THE air injected through the tuyeres of a Peirce-Smith copper converter emerges into the bath of molten matte in the form of a highly turbulent jet. The air jets affect a number of chemical and physical processes occurring in the converter: i) Converting Rate. It is generally recognized that the production capacity of a converter is limited by the flow of air which can be injected through the tuyeres and by the oxygen efficiency. In turn, the air flow is limited by pressure drop considerations or by the amount of splashing within the converter. ii) Oxygen Efficiency. This depends on the dispersion of the air jet in the liquid bath, and its trajectory through the bath. iii) Mixing. The jets act as mixing devices by transferring momentum energy to the bath; in this way the heat generated by the converting reactions occurring in the jets is distributed through the bath. iv) Refractory Wear. The proximity of the jets, which are centers of heat generation, to the refractories in the tuyere zone may have an important effect on refractory life. Mixing conditions in the bath will also influence refractory erosion. v) Splashing, and Accretion Build-Up. The energy of the jets is not dissipated entirely in mixing the bath. particles of liquid are carried out kith the gas above the surface of the bath in the form of liquid spouts and droplets. These result in the undesirable build-up of accretions on the converter mouth, and dust losses in the flue gas. Despite the importance of the interaction of the air jets and the matte in a converter, very few studies of the fluid dynamics of converting have been reported in the literature. Metallurgists in the USSR appear to have been more concerned with the subject than their Western counterparts. Deev et al.1 studied the interaction of an air jet with aqueous solutions in a converter model and qualitatively determined the tuyere air velocity and tuyere inclination which produced the most favorable results with respect to good mixing in the bath, and minimum splashing. Shalygin and Meyer-ovich2 also examined the air-matte physical interaction both in models and in industrial converters; they concluded that in conventional converting practice, there was no significant penetration of the air jets into the matte layer, and consequently the converting reactions occurred mainly in a zone adjacent to the tuyeres. The behavior of air jets in a converter bath, and the aerodynamic characteristics of tuyeres are discussed at length in a monograph on converting by Shalygin.3 However, the description of the phenomena occurring in the converter bath is largely qualitative. The side-blown Bessemer converter for steelmak-ing is very similar to the Peirce-Smith copper converter. Among the few investigations of the behavior of air jets in the bath of a Bessemer converter are those of Kootz and Gille4 who studied splashing in the course of an investigation on the effect of blowing conditions and converter shape on nitrogen pick-up in Bessemer steel. They found that during blowing standing waves were formed on the surface of the bath; the amplitude of the waves increased with the depth and angle of tuyere immersion until the whole bath moved backwards and forwards causing heavy splashing. Kazanstev5 used a model of a Bessemer converter to obtain correlations between the axial velocity of a gas jet and distance from the tuyere orifice and the Froude number of the jet. shalygin3 used these results to calculate the horizontal penetration of an air jet in a copper converter; the penetration was defined as the distance in which the axial jet velocity decreased to 10 pct of its initial value. However, the rising trajectory of the jet was not taken into account. In the absence of quantitative information on the fluid dynamics of converting, the design of copper converters has been based mainly on operating experience. Such experience tends to vary widely from smelter to smelter., This is reflected in Table I which is based on data compiled by Lathe and Hodnett.6 Aside from a rough, and perhaps obvious correlation between the total air flow and converter volume, Fig. 1, no pattern emerges from the data. For example, tuyere throat air velocities vary from 215 to 465 ft per sec in converters of the same size, for little apparent reason. The air jet energy input per cubic foot of converter volume, which may be taken as a measure of the amount of mixing in the converter bath, also varies greatly. A recent analysis of converter data by Milliken and Hofinger7 has also revealed unexplained variations in operating parameters. It is believed that by gaining a better understanding of the fluid dynamics of converting a more rational basis may be provided for the design of converters. In particular, it is proposed that if one takes into account the desirable criteria of a high converting rate, high oxygen efficiency and long refractory life, there should be an optimum configuration of tuyere air flow for a converter of a given diameter. The present investigation is concerned with the form and trajectory of an air jet in a converter bath. The general theory of turbulent jets has been expounded by Schlichting8 and Abramovich.9 However, most experi-

Jan 1, 1970

By A. Mitchell

An approximate phase diagram has been developed for the CaF2-CaC2 system, indicating a eutectic point at 1240°C, Ncac2 = 0.13, and no detectable solid solution in either phase. The liquidus line is shown to correspond to a simple c22- ion in solution. A thermo-chemical study of&apos; the reaction between carbon-saturated Ni-Ca alloys and CaC2-CaF2 liquids indicates that lhe Raoullian activity coefficient of CaC2 in dilute solution in Cap2 al 1500°C lies between 8 and 10. Some effects of the stabilily of Cap2-CaC2 solutions at high temperatures on electroslag remelting praclice are outlined. THE alkaline earth acetylides. MIIC2, have a reasonably high thermochemical stability at high temperature in the solid state,&apos; with the exception of magnesium, which forms an unstable acetylide at low temperatures (-500°C) and a carbide, Mg2C3, in the range 700&apos; to 1000°C. The acetylides of calcium and barium have been shown to have limited solubility in their respective chlorides,&apos; and further these solutions contain the acetylide as a C: ion.&apos; The equivalent magnesium solutions have not been studied. Although calcium "carbide" is used as a desulfuriz-ing reagent in steelmaking. and is possibly present as an acetylide-oxide phase in very basic electric arc practice slags, the acetylide ion appears to be substantially unstable in a silicate slag.* As a conse- *This instability arises from equilibria in the reaction: CaC2 + CO = (Ca0) + 3C where the low intrinsic solubility of CaC2 in silicate lattice, and the low activity of CaO in a silicate solution where CaO/Si02 < 1, combine to give a very small equilibrium concentration of CaC2 in solution in such silicate slags at temperatures in the region of I 500°c, even under carbon-saturated conditions. Under highly basic conditions, a liquid CaO-CaC2 phase may separate from the silicate system quence of this, the possibility that reactions involving CaC2 in silicate solutions are of importance to general steelmaking practice is remote. However, in operations involving a slag primarily based on a halide, or alkaline earth oxide, we must take into account the possibility that CaC2 will appear in quantities sufficient to significantly affect both the chemical and physical properties of the slag. The work outlined below presents a study of the CaF2-CaC2 system intended to provide sufficient data to allow an estimate of the importance of this system to electroslag remelting and welding practice. However, we should indicate at this point that there will be other processes, e.g., heat treatment, flux cleaning of castings, fused salt electrolysis, and so forth, where alkaline-earth halide fluxes are in contact with carbon, graphite, or carbides, and where halide-acetylide solutions must be taken into account. EXPERIMENTAL 1) Structural Studies. In view of the difficulty ex-perienced in handling CaC2 prepared from calcium turnings and propane gas at 700°C, it was decided to use solutions prepared directly in the equilibration apparatus, Fig. 1. The starting materials were: a) Ni-Ca-C alloy, prepared by adding calcium to liquid nickel held under calcium fluoride in an induction-heated graphite crucible; b) calcium fluoride, prepared by fusing calcium fluoride powder (British Drug House "EXTRA PURE") calcium fluoride in an induction-heated graphite crucible, in air, followed by electrolysis between graphite electrodes at 1 amp cm-2 density, for 10&apos; coulombs per g CaF2. This procedure decomposes the CaO produced by hydrolysis during the fusion step, replacing it by CaC2; Ca2+ + 2e-Ca*(l) Ca*(l) + 2C(gr)-(CaC2)caF2 O2- -2e-O*(g) O*(g) +C(gr)-CO(g) This results in a composition of between 2 and 5 wt pct CaC2 in CaF2. Fifty grams (in lumps) of this material were placed in a graphite crucible, together with Ni-Ca-C alloy (averaging 20 wt pct Ca), and the equilibration apparatus assembled. The alloy reacted with the crucible at high temperature to give CaC2, which dissolved in the calcium fluoride solution to give the desired composition. Cooling curves were plotted manually for these liquids, with rapid stirring and CaF2 seeding to minimize supercooling, and using a Pt/Pt 13 Rh thermocouple calibrated on the freezing points of nickel and copper. This gave a reproducibility of ±0.l°C. and an absolute accuracy of the thermocouple of ±l°C. An example curve is shown in Fig. 2, with the CaF2 end of the binary system in Fig. 3. The CaF2-CaC2 ingots were crushed, under dry nitrogen, and sampled for chemical analysis and X-ray examination. Analytical details are given in the Appendix. Powder diffraction data indicated that the only phases present in all samples examined were calcium fluoride and tetragonal (Types I and 111) calcium acetylide,4 with no evidence of solid solutions or compound formation. 2) Thermochemical Studies. The apparatus used to obtain activity data on CaC2 in these systems is shown in Fig. 4. It consists of an arrangement whereby the graphite crucible and its contents (CaF2-CaC2. Ni-Ca-C) can be rapidly cooled without exposure to air. Trial experiments to determine an equilibration time by ap-

Jan 1, 1969

By D. F. Kaufman, H. R. Spedden, A. M. Gaudin

MANY studies of comminution have been made to ascertain the size distribution of the product and to evaluate the work of comminution in the light of the size distributions of the feed and product. Up to now, these studies have been essentially statistical in character, that is, a certain lot of feed was subjected to comminution in some specified way, and the aggregate product was fractionated into sizes, thereby losing all knowledge of individual relationship of feed to product pieces. Radioactive tracers offer a means to do something in this respect which could not be done before, namely, to follow the rupturing of some particular piece in its normal environment of other pieces. That is, it permits going beyond the usual statistical limitations of size distribution studies to what may be termed a personalized or individualized study. The purpose of this paper is to present some preliminary experiments conducted with this tool. The method employed was to mark radioactively some constituent of a feed. It is possible, of course, to consider the preparation of two lots of material of which one is radioactive and the other is not, and to blend the two ahead of the comminuting step; but to do so is open to the objection that the two preparations may not be identical. Therefore a technique has been chosen that removes this objection by merely taking out a size fraction of a comminution feed, rendering that fraction radioactive by exposure to a neutron flux, and then by returning it to Table I. Size Distribution of Offspring Albite Particles Originally 28/35 Mesh and in Admixture with Other Sizes After Grinding 2 min in a Steel Ball Mill Specific Activity &apos; Cumu- Corrected Distrl- latlve Size for Back- butlon In Distri- Fractlon ground, Weight, Product, button, of Product, cpm/gm g Pctb Pct Mesh (A). (W) (P) (ZP) + 28 0 56.0 0 100.1 28/35 62.6 54.0 24.8 75.3 35/48 62.8 59.4 27.7 47.6 48/65 41.1 53.0 16.2 31.4 65/100 29.6 45.7 10.2 21.2 100/150 23.7 37.0 6.6 14.6 150/200 23.3 25.1 4.4 10.2 200/270 20.1 19.0 2.9 7.3 270/400 17.8 21.2 2.9 4.4 -400 22.9 25.2 4.4 — 100.1 a These activity determinations were made in rapid succession in the order given. The specific activity (Ao) of the active 28/35 mesh fraction of the feed was measured at the beginning, after the measurement on the 65/100 mesh size fraction of the product, and; The end. The decay-corrected activities at those times were 246.7, 241.0. and 236.9 cpm per gm. The weight (W0) of the active 28/35 mesh fraction in the feed was 55.0. b Example of calculation for P in the 65/100 mesh oroduct frac- A W tion; A = 29.6, W = 45.7, Ao = 242.7, Wo = 55.0: P = — x — Ao Wo = 0.102 = 10.2 pet. the remainder of the charge for the comminution experiment. A relatively simple procedure was developed by which albite, containing sodium, was activated in the M.I.T. cyclotron. The cyclotron makes highspeed deuterons which impinge on a beryllium target, thereby producing a concentrated neutron flux. The mineral was exposed to this flux for 2 hr. This treatment changed enough of the sodium to sodium 24 (14.8 hr half-life, 1.4 mev ß) as to make detection and measurement easy. The nuclear reactions taking place were: 11Na23 (n,?) 11Na24 (irradiation) 11Na24 ß,?,? 12Mg24 (decay) The detailed technique of the experimentation was as follows: 40 kg of hand-sorted, lump albite were crushed to pass 10 mesh. After careful mixing of the lot, a screen analysis was made. The whole lot of material was fractionated on standard Tyler screens from 14 down to 200 mesh. Samples for experiments were compounded from these fractions in accordance with the screen analysis. When it was desired to make an experiment in which, for example, the 28/35 mesh size fraction was to be studied, the blend of size fractions was made as indicated above, except that the 28/35 mesh size fraction was added only after irradiation in the cyclotron. The blended charge containing the activated albite was ground for 2 min in a laboratory ball mill with a steel ball charge of controlled size distribution. The ground product was carefully sized on a set of Tyler screens in a Ro-tap. Each size was analyzed for radioactivity by the use of an end-window Geiger-Mueller counter and standard scaling circuit. This analysis was carried out in detail as follows: a 20-g sample was placed in a Petri dish, packed carefully to obtain reproducible geometric distribution with reference to the Geiger-Mueller tube, and the activity was counted for a 2-min period. Several determinations of the activity of the active size fraction in the feed were made at various times to establish the decay in activity with time. Linear interpolation was used to evaluate the activity that the active size fraction in the feed would have had at any given instant. The ratio of the observed activity in a size fraction of the product to the activity that the active size fraction in the feed would have had at the same time gives the fraction in the product size that came from the irradiated size in the feed. The general formula for finding the distribution, P, of a specific individual size fraction in the feed

Jan 1, 1952

By C. Altstetter

THE work herein reported is restricted to the carbides which occur in quenched and tempered AISI 43XX steels with carbon contents up to 0.40 pct and silicon additions of up to 3 pct. In view of the instability and extremely small size of the carbides formed at low tempering temperatures, the technique for successfully preparing specimens for X-ray diffraction will be outlined. The alloys listed in Table I were obtained through the courtesy of the United States Steel Corp. in the form of 1/2-in. rounds forged from 100 lb. induction furnace heats (except for 4337 which was a commercial heat). The stock was normalized and then swaged and drawn to 15 mil wire with anneals at 1200F between passes. The wire was austenitized for 45 min in evacuated vycor capsules and quenched into iced brine with simultaneous smashing of the capsule. Tempering was done in air with a water quench after tempering. The carbides were extracted in a simple cell using a solution of 1M KC1 and 0.5 pct citric acid with an initial current density of 0.1 amp per sq cm. One end of a short length of wire was immersed in the solution, and the current at constant voltage was noted as a function of time. After about an hour the current dropped sharply because of the decrease in specimen cross-section. At this point it was found that the dissolution could be stopped and that the very fine wire which then resulted was just large enough to permit handling of the extracted precipitate still clinging to it, yet so small that it diffracted and absorbed only a negligible amount of the X-radiation. This rod of residue with a convenient handle of undissolved wire was rinsed in distilled water. alcohol, and acetone. Then it was dipped in a thin solution of cellulose-acetate cement and dried in vacuum. The resulting specimen was straight, uniform in density, easily handled, but most important, was completely sealed and never exposed to air. Furthermore, the residue had never been subjected to strong acids or rough handling such as in the extraction-replica technique or in the complete extraction to a powdered residue. It was found that improperly coated specimens were pyrophoric, turning to oxide with a dull red glow as they were exposed to air and yielding patterns of Fe2O3 and Fe3O4. The steels containing 3 pct Si were especially difficult to prepare for this reason. The specimens were put in a 57 mm Straumanis camera with double pinholes or slits and irradiated with filtered-chromium radiation. Readable patterns were obtained in less than an hour. A preliminary finding of some note was that for both tempered and as-quenched specimens of steels 4337 and 4337 (1.5 Si). M23C6 patterns were found along with the patterns of other constituents of the residues. This result was somewhat surprising in that previous investigators had reported that this carbide did not appear in a 0.38 pct C, 0.48 pct Mo steel1 or in chromium steels of less than about 10 pct Cr.2 Although the total amount of carbide-forming alloying elements is less than 2 pct, due to their mutual interaction and the action of the plastic deformation in promoting equilibrium, this carbide was able to form even in the steel containing 1.5 pct Si. M23C6 was not detected in the 4337 (3.0 Si) steel and the lower-carbon steels were not investigated in this condition. It is very likely then that the steels studied herein underwent a fourth stage of tempering during the anneals at 1200°F. This result has significance in that even a small amount of undissolved M23C6 in a low-carbon, low-alloy steel would exert a large effect on its hardenability. Its presence would also influence the mechanical properties by decreasing the carbon content of the matrix. Annealing in vacuum for 1 to 4 hr in the austenite field removed all traces of MZ3C+ The results on carbide precipitation during tempering, summarized in Table I, are in agreement with those of Klingler et al.3 for the higher carbon steels. For the AISI 4337 steels it is noteworthy that in the steels with added silicon the E carbide persists to longer times and higher temperatures and that silicon delays the formation of cementite. The results for the lowzr-carbon steels parallel those of the higher-carbon grade. The appearance of E carbide in the AISI 4315 is significant. There is considerable disagreem-nt in the literature as to whether this carbide forms in the tempering of steels containing less than about 0.2 pct C. Following the detection of E carbide in a 0.18 pct C plain-carbon steel,4 its occurrence in a steel containing chromium and molybdenum should be expected. The fact that the low-carbon steels have the same carbide-precipitation sequence as the high-carbon steels has bearing on the larger problem of the exact tempering reactions in all steels. Following the suggestion of Roberts et al.,&apos; the first stage has been generally assumed to result in a metastable equilibrium of c carbide and martensite of about 0.25 pct C. From this it was concluded that a steel having less than 0.25 pct C should then be under-saturated with respect to c carbide and should not precipitate this carbide upon tempering. In view of the experimental findings of c carbide in steels hav-

Jan 1, 1962

By E. Miller, K. L. Komarek, M. Ettenberg

The activity of aluminum in solid Co-A1 alloys has been measured by an isopiestic technique between 850° and 1200°C from 45 to 80 at. pct Al. The activity shows a Precipitous decrease around the stoichzornetric composition of CoAl. Free energies of mixing have been calculated over a limited composition range. Considering an antistructure-vacancy defect mechanism, the degree of intrinsic disorder, a , in CoAl was related to the alunminum activity. Excellent agreement between the calculated and experimental activity curves was obtained for a = 1.25 x 10-4. ThERMODYNAMIC properties of solid aluminum-transition metal alloy are being studied in an investigation of disordering in ordered compounds. In a continuing series of investigations, activities of solid Fe-1,&apos; Ni-A1, kd r-A13 alloys have been measured. From the results for Fe-A1 and Ni-A1, the degree of intrinsic disorder for the equiatomic compounds was calculated2 using equations derived by Wagner and chottk. From the results for Cr-A1 the degree of intrinsic disorder was calculated from equations derived by Orr.&apos; In this paper, the results of the study of Co-A1 alloys are described. Published activity data in the Co-A1 system has been limited to liquid alloys at 1600°C.° A heat capacity study7 of stoichiometric CoAl indicated that a second-order phase transformation occurs at 790° C, attributed to an order-disorder reaction. Oelsen and Middel,&apos; employing the calorimetric mixing of pure liquid metals, obtained heats of formation for compositions from 6 to 90 at. pct Co. Heats of formation for 50 and 78 at. pct Co alloys have also been measured by acid solution calrimetr. The Co-A1 phase diagram, as compiled by Hansen and Anderko,lo is in good agreement with more recent X-ray evidence. The method for measuring activities of aluminum in this study is essentially that employed in the studies of the Fe-1,&apos; i-Al, and r-A13 systems. This isopiestic method entails placing cobalt specimens, in a temperature gradient, in a sealed alumina system containing a pure liquid aluminum source of fixed vapor pressure. The specimens are equilibrated, cooled to room temperature, and their final compositions determined. From the measured temperature of the specimens and the known vapor pressure of pure aluminum the activities of aluminum in the alloy can be calculated. EXPERIMENTAL PROCEDURE The cobalt was 3-mil-thick sheet of 99.9 pct purity (herritt Gordon Mines Ltd., anada). The major impurities were 0.1 pct Ni, 0.014 pct C, 0.018 pct Fe, 0.004 pct S, and 0.005 pct Cu. The aluminum metal had a purity of 99.99 pct (Aluminum Corp. of America) and all alumina parts were 99.7 pct A1,O3 (Triangle RR Grade, Morganite Refractories, Inc.) with major impurities 0.05 pct SiOz, 0.1 pct Fe203, 0.2 pct NazO, and 0.05 pCt K20. Runs 1 to 3 were made with annular cobalt specimens (12 mm ID by 21 mm OD) punched from the sheet. The specimens were deburred and degreased in carbon tetrachloride and in acetone. The samples, each weighing about 150 mg, were then positioned along an alumina rod, a in. OD by 14 in. long, separated by alumina spacers, i in. ID by | in. OD by & in. long. The lower end of the rod was placed in a hole drilled in the center of an 80-g aluminum cylinder. This assembly was put into an alumina crucible, 1+ in. ID by 13 in. OD by 3+ in. high, and the position of each sample was measured to within 50.5 mm relative to the bottom of the crucible. An alumina tube, 28.5 mm ID by 35.5 mm OD by 14 in. long, closed at the top, was slipped over the whole assembly, so that it fitted snugly into the bottom crucible. The entire reaction assembly was tied with molybdenum wire and lowered into a mullite tube, closed at the bottom. A quartz thermocouple tube, closed at one end, containing a t/Pt-10 pct Rh thermocouple, calibrated according to the specifications of the National Bureau of standards,&apos;&apos; was placed along the reaction assembly inside the mullite tube. The temperature of each specimen could be determined by gradually raising the thermocouple and measuring the temperature gradient along the reaction assembly. The combined error in temperature measurement and sample position resulted in a total error of Q°C in the recorded temperature of each sample. The mullite tube was sealed at the top by a water-cooled brass head, connected to a conventional glass vacuum system. The aluminum reservoir is heated to its melting point sealing the alumina system containing the samples. During this process the pressure is maintained below 0.01 li Hg. During subsequent heating to establish the proper temperature gradient and throughout the entire run the pressure is maintained below 2 1 Hg by means of a two-stage mechanical pump. Equilibration runs lasted from 4 to 6 weeks and were terminated by air cooling. The temperature of the liquid aluminum reservoir was brought below its melting point in less than 20 min. For runs 4 and 5, alloy buttons with 49 and 69 at. pct A1 were prepared from the initial high-purity metals by arc melting under purified argon. The alloy buttons were comminuted to powder with an alumina mortar and pestle until the powder passed through a 400-mesh screen, particle size 0.0014 in. Portions of this powder weighing between 50 and 200 mg were placed in small alumina trays, 25 by 15 by 5 mm, which were then

Jan 1, 1969

By V. E. Elliott, C. L. Meyette

THE conditioning of semifinished steel products such as billets, blooms, and slabs to remove surface defects before further processing to finished products is a necessary accompaniment to steel mill rolling operations. A knowledge of the kinds of defects which occur and of the conditions in melting, teeming, and rolling that may lead to their occurrence is favorable to the production of quality products. Surface defects may be classed as either of mechanical origin such as those that occur in the heating and rolling operations and include breaks, tears, guide marks, mechanical laps and the like, or they may have been in the ingot before heating and rolling. Examples of the latter are ingot cracks, blow-holes, scabs, and inclusions which lead to the numerous known types of seams -and surface flaws. Most of the common types of surface defects and methods for their identification by visual examination or by the aid of macro-etch tests are well known. The conditions which caused their formation are also appreciably understood and this knowledge has been instrumental in the establishment of methods for metallurgical control. There are, however, defects of doubtful origin. In any endeavor to trace the causes for their occurrence, the question of first concern is: I. Whether they were formed in the rolling procedure. 2. Whether they existed in the ingot prior to rolling. In the case of semifinished products which are rerolled to finished products there is also the question of whether they were formed in the primary or in the secondary rolling. In metallurgical laboratories where numerous or routine examinations of the quality of rolled products are made over the course of time, there will doubtless be many puzzling cases of defect origin. Microscopic examination of the defects may, however, reveal a characterizing condition that can be used to classify them broadly with respect to their origin. Such a condition has been observed and, after detailed investigation, is described here with the thought that it may offer a useable and relatively simple solution to a bothersome problem. BASIS FOR CLASSIFYING In this discussion the term "mechanical type defects" will be used to designate those that have occurred as a result of the rolling operations such as in rolling from the ingot to billets, blooms, or slabs or in rerolling to finished products. The term "steel type defects" will he used to designate those that were present in the ingot prior to primary rolling or that were in the semifinished product prior to secondary rolling to finished product. The basis for distinguishing between the two types of defects lies in the relative degree of subscale formation surrounding them. Subscale is defined&apos; as a zone of

Jan 1, 1948

By A. S. Richardson

AIR conditioning, or air cooling, for the improvement of ventilation in the Butte mines has come into increasing use during the past 10 years. In part, the methods practiced have been described in previous publications of the Institute, but some improvements on earlier methods have been made and a number of new features have been developed. This paper is presented as a record of progress made, and for the sake of completeness describes all general features of the work. The need for air conditioning in the ventilation of mines in the district arises from the fact that the temperature of the ground and mine water has shown a very great increase with increase in mining depth, and has now reached a maximum of slightly over 130ºF. The most difficult part of the ventilation problem is the maintenance of temperature and humidity of a satisfactory standard in the working places, especially on the lower levels. Although ordinary ventilation is adequate to maintain good conditions in most of the working places it is subject to a number of limitations at great depth. Most important among these limitations is that with increase in depth the air becomes heated before it reaches the working places, both by compression from increase in atmospheric pressure and by heat transferred to it from rock at high temperature, so that its capacity for lowering temperatures is greatly reduced before it reaches the operating zone. Increasing depth of mining also increases the distance traveled by the air in its passage through the mine, and this causes a corresponding increase in resistance to air flow, so that there is greater difficulty in maintaining even the same volume in circulation. Thus, in the face of a demand that the ventilating system have a very much greater capacity to remove heat from the mine, the tendency is for that capacity to diminish. The only evident alternatives were (I) the opening of additional air shafts to increase the volume of air in circulation, (2) an extension of the existing system that would be subject to the same limitations, or (3) the adoption of an entirely different method such as air cooling. Fortunately for an economic solution of the problem, the mean annual temperature of the surface atmosphere at Butte is about 40°F., with very low relative humidity in summer, so that there is unlimited natural cooling power at a temperature range adaptable to air-conditioning methods. METHODS Two similar methods of air conditioning are used, as necessitated by service requirements and dependent upon the equipment available. In one, which is the more important and has the greater cooling capacity, water is circulated in a closed circuit, and, alternately, first absorbs heat from warm mine air and then dissipates it in the surface atmosphere by cooling at a cooling tower. The second

Jan 1, 1941

By V. L. Elliott, C. L. Meyette

The conditioning of semifinished steel products such as billets, blooms, and slabs to remove surface defects before further processing to finished products is a necessary accompaniment to steel mill rolling operations. A knowledge of the kinds of defects which occur and of the conditions in melting, teeming, and rolling that may lead to their occurrence is favorable to the production of quality products. Surface defects may be classed as either of mechanical origin such as those that occur in the heating and rolling operations and include breaks, tears, guide marks, mechanical laps and the like, or they may have been in the ingot before heating and rolling. Examples of the latter are ingot cracks, blow-holes, scabs, and inclusions which lead to the numerous known types of seams and surface flaws. Most of the common types of surface defects and methods for their identification by visual examination or by the aid of macro-etch tests are well known. The conditions which caused their formation are also appreciably understood and this knowledge has been instrumental in the establishment of methods for metallurgical control. There are, however, defects of doubtful origin. In any endeavor to trace the causes for their occurrence, the question of first concern is: I. Whether they were formed in the rolling procedure. 2. Whether they existed in the ingot prior to rolling. In the case of semifinished products which are rerolled to finished products there is also the question of whether they were formed in the primary or in the secondary rolling. In metallurgical laboratories where numerous or routine examinations of the quality of rolled products are made over the course of time, there will doubtless be many puzzling cases of defect origin. Microscopic examination of the defects may, however, reveal a characterizing condition that can be used to classify them broadly with respect to their origin. Such a condition has been observed and, after detailed investigation, is described here with the thought that it may offer a usable and relatively simple solution to a bothersome problem. Basis For Classifying In this discussion the term "mechanical type defects" will be used to designate those that have occurred as a result of the rolling operations such as in rolling from the ingot to billets, blooms, or slabs or in rerolling to finished products. The term "steel type defects" will be used to designate those that were present in the ingot prior to primary rolling or that were in the semifinished product prior to secondary rolling to finished product. The basis for distinguishing between the two types of defects lies in the relative degree of subscale formation surrounding them. Subscale is defined1 as a zone of

Jan 1, 1949

By V. L. Elliott, C. L. Meyette

The conditioning of semifinished steel products such as billets, blooms, and slabs to remove surface defects before further processing to finished products is a necessary accompaniment to steel mill rolling operations. A knowledge of the kinds of defects which occur and of the conditions in melting, teeming, and rolling that may lead to their occurrence is favorable to the production of quality products. Surface defects may be classed as either of mechanical origin such as those that occur in the heating and rolling operations and include breaks, tears, guide marks, mechanical laps and the like, or they may have been in the ingot before heating and rolling. Examples of the latter are ingot cracks, blow-holes, scabs, and inclusions which lead to the numerous known types of seams and surface flaws. Most of the common types of surface defects and methods for their identification by visual examination or by the aid of macro-etch tests are well known. The conditions which caused their formation are also appreciably understood and this knowledge has been instrumental in the establishment of methods for metallurgical control. There are, however, defects of doubtful origin. In any endeavor to trace the causes for their occurrence, the question of first concern is: I. Whether they were formed in the rolling procedure. 2. Whether they existed in the ingot prior to rolling. In the case of semifinished products which are rerolled to finished products there is also the question of whether they were formed in the primary or in the secondary rolling. In metallurgical laboratories where numerous or routine examinations of the quality of rolled products are made over the course of time, there will doubtless be many puzzling cases of defect origin. Microscopic examination of the defects may, however, reveal a characterizing condition that can be used to classify them broadly with respect to their origin. Such a condition has been observed and, after detailed investigation, is described here with the thought that it may offer a usable and relatively simple solution to a bothersome problem. Basis For Classifying In this discussion the term "mechanical type defects" will be used to designate those that have occurred as a result of the rolling operations such as in rolling from the ingot to billets, blooms, or slabs or in rerolling to finished products. The term "steel type defects" will be used to designate those that were present in the ingot prior to primary rolling or that were in the semifinished product prior to secondary rolling to finished product. The basis for distinguishing between the two types of defects lies in the relative degree of subscale formation surrounding them. Subscale is defined1 as a zone of

Jan 1, 1949

By F. J. Plecity, W. C. Leslie, F. W. Aul

During isothermal recrystallization, the rate of grain growth in dilute Fe-hlo alloys decreased rapidly with increasing Mo content, up to -0.04 at pct, and less rapidly therea-fter. Rate of growth also decreased sharply with time at constant temperature. The observed rates of boundary migration did not cor,espond to predictions of the Lucke-Detert theory. It is proposed that the growth of recrystallized grains is inhibited by clustering of solute atoms at inzperfections in the unrecrystallized matrix. It is now firmly etablished" that the rate of re-crystallization of cold-worked metals, i.e., the rate of growth of recrystallized grains into the deformed matrix, is greatly inhibited by the presence of alloying elements in solid solution. The effect is greatest with the first very small quantity of alloying elements, and additional increments cause much less pronounced retardation of growth. The early papers on this subject were reviewed in Ref. 6. The mechanism of retardation of growth is not clear; only one theory, due to Lucke and Detert? has been advanced. This assumes an elastic interaction between grain boundaries and solute atoms which tends to increase the concentration of the latter in the grain boundaries. Except at very low solute concentrations or at high temperatures, the mobility of the boundary is assumed to be controlled by the rate of diffusion of the accompanying solute atoms. Abrahamson and Blakeney2 have noted a correlation between "recrystallization temperature of binary alloys of iron and the number of d-shell electrons in the solute atoms. There is need for considerably more experimental data on the effect of solute elements on the rate of migration of grain boundaries into the deformed matrix, to provide the basis for an understanding of the annealing process in metallic solid solutions. Only a start has been made in this direction. To avoid unnecessary complications, alloys in which precipitation does not occur should be used, but to produce the maximum effects it is desirable to select alloys with a large difference between the sizes of the atoms of the solvent and solute. For these reasons, alloys of iron and molybdenum sen for this study. MATERIALS AND PROCEDURES A 30-lb. ingot of iron and four similar ingots of Fe-Mo alloys were vacuum melted in magnesia crucibles and poured into cast-iron molds. The molybdenum contents were planned according to the results of Abrahamson and Blakeney2 sothattwoalloyswould fall in the region of rapid change of recrystallization kinetics with change in composition (0.006 to 0.015 and 0.030 to 0.045 at. pct Mo) and two alloys would fall in the region of gradual change (0.18 to 0.24 and

Jan 1, 1962

By S. W. Poole, J. A. Rosa

THE object of this investigation was to determine the distribution of chemical elements within a large, killed alloy-steel ingot, by sulphur printing and quantitative chemical analysis. With regard to segregation in steel ingots, the factors of melting practice, pouring temperatures, mold design, etc., and the mechanics of solidification and its attendant functions, have been the subject of intensive study over a period of years by many investigators. Notable among these is the Sub-Committee of the No. 5 Committee of the British Iron and Steel Institute. For an exposition 0f the many problems awaiting the researcher on the heterogeneity of steel ingots, the methods of attacking these problems, together with some of the answers, the reader is referred to the nine reports and numerous papers of that committee and its membership. STEELMAKING DATA Melt.-The heat was made in a 70-ton direct arc-type basic electric furnace. Furnace charge consisted of nickel-chromium-molybdenum steel, most of it in the form of heavy mill scrap. All of the scrap was charged cold. The standard double-slag method was employed, the heat being finished under a strong carbide slag. Aluminum was used as the deoxidizing agent. Tapping temperature, as observed with an optical pyrometer, was 3000°F. Detail of Mold and Ingot Size.-Details of the ingot mold and the ingot itself are given in Fig. I. Teeming.-Teeming temperature of the subject ingot as observed with an optical pyrometer was 2830°F. The ingot was top-poured directly through a 1 ½ in. nozzle and required 7 min., 44 sec. to fill up to the hot top. An additional 2 min., 30 sec. were required to fill the hot top. The ingot was stripped hot and charged with the remainder of the heat into an annealing furnace. There it was given the standard annealing cycle used for these ingots. Subsequent heat-treatments are described elsewhere in this paper. SECTIONING AND PREPARATION FOR SULPHUR PRINTING Because of previous favorable experience in sectioning ingots up to 21 ½ in. square with an oxyacetylene torch, it was decided to use this method to section the subject ingot. The ingot was preheated to 900°F. for 12 hr. It was then placed on a steel bed in a horizontal position so that the longitudinal axis was level and parallel to the track of the motor-driven torch carrier. Two cuts were made, one 2 in. above the longitudinal axis and the other 2 in. below. The time required to make each cut was approximately 75 min. The cutting operation is shown in Figs. z and 3. The 4-in. thick slab was mmediately charged into a furnace standing at 1200°F.

Jan 1, 1944

By G. K. Manning, A. R. Elsea, A. B. Westerman

INTRODUCTION A CONSIDERABLE number of high-temperature alloys, that is, alloys which have load-carrying ability at elevated temperatures, have been developed on an empirical basis. In order to determine why these alloys possess this particular ability, a project was started at Battelle Memorial Institute on the fundamental factors promoting high-temperature strength of alloys. At the time of inception of this study, the cobalt-base alloy, Vitallium, was widely used because of its good high-temperature properties. One phase of this study was to include an investigation of the structures observed in Vitallium after various heat treatments. However, before investigating the structural features of Vitallium, it appeared logical to examine the phase diagrams of the related binary systems in order to develop information as to which phases- might be present in Vitallium. A preliminary survey of the pertinent alloy systems was made, with particular emphasis on the cobalt-chromium system, which is the base for the Vitallium series of alloys. The early work of Lewkonja1 and Guertler2 indicated that cobalt and chromium are completely miscible in the liquid state, and, within a narrow temperature range, in the solid state; that the liquidus shows a minimum; and that the alloys containing 45 to &apos;85 pct chromium undergo a transformation at 1200 to 1250°C. More recently, Wever and Haschimoto,3 Wever and Lange,4 and Matsunaga5 carried out experimental work which led to the diagrams shown in Fig I and 2. Both diagrams are based on thermal analysis, metallographic, magnetic, and dilatation data; in addition, X ray diffraction results were used by Wever and Haschimoto, and electrical resistance measurements by Matsunaga. It is apparent from a comparison of the two diagrams that there was a difference of opinion as to the locations of the boundaries of the various phases, and as to the existence of a phase containing approximately 47 pct chromium. With these exceptions noted, it might be pointed out that the two diagrams are similar, and that, in general, any particular reaction which is shown on both diagrams occurs at a lower temperature on the Matsunaga diagram than on that of Wever-Haschimoto-Lange. Thus, in view of the gaps in the data and the questionable features in the published diagrams, it appeared desirable to start the fundamental study of Vitallium by determining the diagram for the cobalt-chromium system. EXPERIMENTAL WORK For the convenience of the reader, the diagram as determined by the present investigation is presented in Fig g. The liquidus and solidus data for the low-chromium alloys were taken from the work of Wever and Haschimoto,3 while the, melting point for pure chromium is the

Jan 1, 1948

By R. C. Earlougher, F. G. Miller, T. D. Mueller, H. J. Ramey

There are many studies of flow in radial systems that can be used to interpret unsteady rerervoir flow problems. Although solutions for systems of infinite extent can be used to generate solutions fur finite ow systems by superposition, application is tedious. In this paper a step is made toward simplifying calcu1ations of such solutions for finite flow systems. Superposition is used to produce a tabulu-lion of the dimension1e.s.s pressure drop function at several locations within a bounded square that has a well at its center. The square system provides a useful building block that may be used to generate flow behavior for any rectangular shape whose sides are in integral ratios. Values of the tabulated dimensionless pressure drop function are simply added to obtain the dimensionless pressure drop function for the desired rectangulm system. The rectangular system may contain any number of wells producing at any rates. Furthermore, the outer boundaries of the rectangular system may be closed (no-flow) or they may he at constant pressure. Mixed conditions also may be conyidered. Tables of the dimensionless pressure drop function for the square system are presented and various applications of the technique are illustrated. Introduction In 1945, van Everdingen and Hurst&apos; published solutions for the problem of water influx into a cylindrical reservoir. Since this problem is mathematically identical with the depletion of a cylindrical reservoir with a well at the origin, the van Everdingen-Hurst solution may be used to study the depletion problem. In their analysis, they assumed that the fluid had a small, constant compressibility such that flow was governed by the diffusivity equation For a constant production rate q starting at time zero, van Everdingen and Hurst showed that the unsteady pressurc distribution for both finite and infinite systems could be expressed in terms of a dimensionless pressure &apos;Sabulations of the dimensionless pressure drop for a unit value of r, were provided by van Everdingen and Hurst,&apos; and later by Chatas.&apos; Others also presented values in graphical or tabular form." If the radius of the well becomes vanishingly small, r,+ O, the line source solution may be used for Eq. 2 when infinite systems are considered. Eqs. 5 and 6 are excellent approximations for Eq. 2 under certain conditions: In 1954, Matthews, Brons and HazebroekV emonstrated that solutions such as Eq. 5 can be superposed to generate the behavior of bounded geometric shapes; i.e., the behavior of a bounded single-well system can be calculated by adding together the pressure disturbances caused by the appropriate array of an infinite number of wells producing from an infinite system. These wells are referred to as image wells. Matthews, Brons and Hazebroek considered systems containing a single well producing at a constant rate. This superposition can be represented analytically as

Jan 1, 1969

By S.H. Ash, P.S. Miller

Extensive and diversified resources justify large populations and great industries. To carry on the business of commerce and meet the demands of large populations, the utilization of tunnels in some form for transportation purposes constitutes an important link in modern civilization. The driving of tunnels has been appropriated by the tunneling branch of the heavy-construction industry, and the progressive steps taken by modern tunnel builders were not even dreamed of 50 years ago. Great strides have been made toward more rapid progress in tunneling in the United States during the past I0 years. Tunneling consists of a definite cycle of operations developed from ideas that are crystallized and translated into action programs through various engineering phases that begin with the first preliminary survey and do not end until the job is completed. Once the line of the bore is established and a time set for the completion of the work, the face must advance according to estimates prepared before the work commences. This schedule must be followed in regular sequence from the moment the drills start against a new face of rock until they are ready again to drill the Succdeding face, constituting a round. Mining is largely tunneling carried on under conditions often more inherently hazardous than actual tunnel construction, but for various reasons" tunne1ing is more hazardous than mining in any branch of the mineral industry. On the other hand, obstacles are sometimes encountered in heavy-construction tunneling projects that when met in mining enterprises do not offer comparable tasks to avoid or overcome them. One is the existence of water under high pressures. In mining enterprises, various alternatives offer a solution in driving a tunnel, even to the extent of its discontinuance or the abandonment of the mine, but a "construction" tunnel usually must go forward because some important project depends largely if not entirely upon it. This paper describes an unusual method of driving a water-supply tunnel through rock carrying water under pressures and conditions that did not permit the use of ordinary tunneling methods. The Delaware Aqueduct The new Delaware aqueduct is a Manhattan project of some magnitude; when regular it will contain what probably will be, for some time to come, the longest tunnel in the world. Various features in its construction are currently described in the trade journals of the construction industry, and informative engineering details are given in the Delaware Water Supply News, published twice a month by the Board of Water Supply of the City of New York. Work was begun on this project on March 24, 1937. The tunnel will convey water from reservoirs at the headwaters of the Delaware River to the City of New York.

Jan 1, 1943

By P. S. Miller, S. H. Ash

Extensive and diversified resources justify large populations and great industries. To carry on the business of commerce and meet the demands of large populations, the utilization of tunnels in some form for transportation purposes constitutes an important link in modern civilization. The driving of tunnels has been appropriated by the tunneling branch of the heavy-construction industry, and the progressive steps taken by modern tunnel builders were not even dreamed of 50 years ago. Great strides have been made toward more rapid progress in tunneling in the United States during the past I0 years. Tunneling consists of a definite cycle of operations developed from ideas that are crystallized and translated into action programs through various engineering phases that begin with the first preliminary survey and do not end until the job is completed. Once the line of the bore is established and a time set for the completion of the work, the face must advance according to estimates prepared before the work commences. This schedule must be followed in regular sequence from the moment the drills start against a new face of rock until they are ready again to drill the Succdeding face, constituting a round. Mining is largely tunneling carried on under conditions often more inherently hazardous than actual tunnel construction, but for various reasons" tunne1ing is more hazardous than mining in any branch of the mineral industry. On the other hand, obstacles are sometimes encountered in heavy-construction tunneling projects that when met in mining enterprises do not offer comparable tasks to avoid or overcome them. One is the existence of water under high pressures. In mining enterprises, various alternatives offer a solution in driving a tunnel, even to the extent of its discontinuance or the abandonment of the mine, but a "construction" tunnel usually must go forward because some important project depends largely if not entirely upon it. This paper describes an unusual method of driving a water-supply tunnel through rock carrying water under pressures and conditions that did not permit the use of ordinary tunneling methods. The Delaware Aqueduct The new Delaware aqueduct is a Manhattan project of some magnitude; when regular it will contain what probably will be, for some time to come, the longest tunnel in the world. Various features in its construction are currently described in the trade journals of the construction industry, and informative engineering details are given in the Delaware Water Supply News, published twice a month by the Board of Water Supply of the City of New York. Work was begun on this project on March 24, 1937. The tunnel will convey water from reservoirs at the headwaters of the Delaware River to the City of New York.

Jan 1, 1943

By Roland Blanchard

ABSTRACT RECENT discovery at Mount Isa of copper mineralization in commercial amount at a depth of 1000 ft., coinciding with downward termination of ore at about the same depth within the larger silver-lead-zinc lenses that have been the standby of Mount Isa&apos;s production to date, has been cited as an example in support of mineral zoning. A previous paper by the author and Graham Hall1 furnished a detailed description of the geology of the ore at Mount Isa as exposed up to that time, but necessarily dealt mainly with the silver-lead-zinc mineralization. Most of the geologic facts that constitute the first half of the present paper were set forth in the previous one in much greater detail, with full supporting evidence for the facts cited. The large amount of underground development (approximately 20 miles) and the extensive exploration carried out by diamond drilling (100,000 ft.) at Mount Isa, added to extensive microscope work conducted over a period of years, both by the company&apos;s staff and by others, had made possible the calculation within fairly close limits of mineralogical composition of the principal mineralized block of ground down to 1000-ft. depth, and had established closely the mineral succession, with reasons for deposition of the various minerals in the patterns now occupied by them. The geologic facts as outlined in the previous paper remain as stated; but because substantial development within the new copper ore body and further exploratory diamond drilling within the new silver-lead-zinc area (Race-course) have taken place since that paper was written, statements and figures relating to those two areas in the present paper supersede those furnished in the previous one. The recent work likewise has established more clearly the paragenetic relationship between the chalcopyrite and galena. Evidence confirming the relationship is furnished in the present paper. The facts of ore occurrence at Mount Isa show [ACCEPTED ZONAL SUCCESSION Silver sulphantimonides Galena Sphalerite Tetrahedrite Arsenical sulphides Chalcopyrite Pyrrhotite MOUNT ISA SUCCESSION Chalcopyrite In the main but Silver sulphantimonides wholly Tetrahedriteably not Galenacontemporaneous Pyrrhotite Sphalerite Arsenical sulphides They show further: (I) that instead of the silver-lead minerals yielding to increased zinc in depth, the zinc yields to increased silverlead; (2) no dovetailing of the silver-lead-zinc sulphides into chalcopyrite takes place; (3) despite the large amount of pyrrhotite deposited in the district (estimated at upward of 100,000,000 tons), its deposition took place under moderately low temperature conditions; (4) no evidence has been found for increase in temperature of deposition, with depth, to deepest exploration in ore (1495 ft.). The anomalous condition at Mount Isa, both as to the unorthodox mineral succession and the largely unorthodox pattern of mineral distribution, is explained in the present paper,

Jan 1, 1943

By J. E. Burke

Recent investigations have elucidated many of the phenomena of the grain growth process, but have also revealed some conflicting and unexplained results. Beck and his co-workers 1,2,3 have shown that grain growth continues with continued heating at one temperature until the average grain size approaches the thickness of the specimen. Plotting the logarithm of the average grain diameter, D, against the logarithm of the annealing time, t, they find the straight line relationship given by the equation: D = Ktm [,] with possible small deviations at short annealing times. K and n are constants at constant temperature. On the other hand, Wa1ker4 finds that, in alpha brass) the rate of growth falls off more rapidly than indicated by Eq i after long annealing, so that an equilibrium grain size is approached. Burke5 showed, using Walker&apos;s data, that time and temperature for grain growth are apparently related through an activation energy, H, according to the relationship: ] where h and tz are the annealing times necessary for the average grain size to increase from Do to D at temperatures T1 and T2 and R is the gas laws constant. In the case quoted, H had the value 60,000 cal per mol. The apparent validity of this relationship, at least up to 700°C, and the approximate value of H were later confirmed by Beck3 The results obtained by Beck Kremer, Demer and Holzworth2 for aluminum and aluminum-magnesium alloys could not be satisfied by such a relationship, since the slope of the isothermal curves increased with increasing temperature. These data indicate and Beck, Holzworth and HuV ater demonstrated expcrimentally that the only apparent factor controlling the rate of grain growth at constant temperature is the grain size. While many of the phenomena have been elucidated, a reasonably quantitative explanation of the process is lacking. There exists uncertainty even as to the primary driving force for grain growth, although there is a considerable body of indirect evidence that the interfacial energy of the grain boundary is responsible.7,8,io Making implicit use of this assumption, several authors14,16 have pointed out that grain boundaries should migrate toward their center of curvature. Harker and Parkerg have advanced this concept furthest, and show that one can expect grain boundary migration to occur only when the grain faces are curved, or when they meet at non-equilibrium angles. When the face is curved toward a grain A, for example, the atoms in the surface of grain B, on the other side of the boundary7 are on the average more surromded by the atoms of their lattice than the atoms on the surface of grain A. Because of thermal motion, the atoms at the interface will sometimes be attached to grain A and

Jan 1, 1949