Search Documents

By R. F. Slack, J. C. Draper, J. A. Younkins

In 1959, the Duquesne Light Co. was faced with the problem of moving more than 40 million tons of bituminous coal in Greene County, Pa. The coal had to travel a distance of about 4 ½ miles from a new mine portal in Rocky Run Valley to the company preparation plant and loading facilities on the Monongahela River. After careful study of this immense transport problem, Duquesne decided that the belt conveyor system described in the following pages offered the best solution. This system, now in operation, is probably one of the four or five longest permanent overland conveyor systems in existence. The general layout of the entire system is shown in Fig. I. A detailed description of the salient features of the system is presented below. THE MINE The valley of Rocky Run where the system begins is very, very narrow and very steep. It was chosen as the site of Duquesne's new mine portal because it was the only place on this particular property where the Sewickley coal seam cropped out. The valley also had two other advantages. First, it fronted on a state road and, second, it offered a site where some 4 million gallons of water could be stored for use in dust-allaying sprays needed in the mine. The company elected to construct a drift mine in the valley because this would require neither the hoisting time of a shaft mine nor the walking time of a slope mine. As part of the mine construction project, the valley was leveled by relocating its stream and filling its center with material cut from each side.

Jan 11, 1966

By H. H. Stout

IN the early fall of 1925, the writer was conducting, in the Ledoux and Co. labora-tory, New York, experiments directed to-ward ascertaining the effect on its impurity content when cathode copper was subjected to a current of various gases at an elevated temperature below the melting point, The apparatus consisted of a vertical 1-in. dia. silica tube about 12 in. long, heated on the outside, The cathodes were broken to pass a8-in. mesh, and a current of various differ-ent gases was passed up through a 4-in, long column of these loose cathode particles in the vertical tube furnace. Temperature was maintained to i500° to 1600°F. and the gas treatments lasted from 3 to 6 hr, The writer observed that whenever reducing gas (H2 or CO) was used, these cathode par-ticles stuck together at points of contact with each other. The cohesion was so marked and tenacious that an examination was made of the fractured surfaces, when cathode particles were broken from the cluster. Crystal growth was always found to have taken place across the surfaces where separate particles were in contact, but only after all oxides, sulphates, etc, had been completely removed. The idea of a possible new process was then conceived and was disclosed to A. M. Smoot (V. P. Ledoux and Co.) with intent to obtain his views. The first conception as given Smoot was "to gas-clean broken cathodes, put them in an extrusion press, solidify and extrude them at around 1500°F," Smoot's reaction, after a few moments considera-tion, was, "It looks perfectly all right to me."

Jan 1, 1940

By C. E. Wood, T. L. Joseph

This paper is a brief report of experimental work undertaken determine whether barium oxide in any quantity increases the desulfur ing action of blast-furnace slags. Industrial furnace operation wi slag containing small quantities of barium oxide, referred to later, intc ested S. A. Sanford of the Commercial Chemical Co., Youngstown, Oh to conduct experiments to furnish comparative results on desulfurizati with normal slag and slag containing small quantities of barium oxic The U. S. Bureau of Mines agreed to assist on the problem because the possible saving in fuel if the desulfurizing action of blast-furna slag can be substantially increased, also because the experiments woi yield new information on sulfur elimination in general, a matter economic importance in furnace practice. A more complete and func mental study of desulfurization of iron by slag is in progress. Distribution of Sulfur iN the Blast Furnace More than 90 per cent. of the total sulfur entering the blast furnz is in the coke. Sponge iron formed by reduction of iron oxides absor part of the sulfur as ferrous sulfide. Kinney's examination of sample taken from various levels of a 3004,011 furnace, shows that the me continues to take up sulfur until it reaches a level near the tuyer Desulfurization must therefore take place as the metal falls through t slag and as the slag and metal exist as layers in the crucible. The relative amounts of sulfur removed while the metal falls throu the slag and while the slag and metal exist as layers in t crucible are not definitely known. Preliminary experiments by t

Jan 1, 1929

By W. H. Bassett, J. C. Bradley

In considering the effects of reducing gases on hot solid copper the following conclusions have been reached. (I) Depth of deoxidation of copper heated in reducing gas is grealer the smaller the amount of cuprous oxide originally present in the copper, the range studied being from 0.015 to 0.136 per cent. oxygen. It is suggested that the reason for this diflerence in depth of deoxidation is thai, when the copper is low in cuprous oxide, the reducing gas is diluted less by the gas that is formed in the reaction than when the copper is high in cuprous oxide; and the greater the concentration of the reducing gas the deeper the deoxidation. (2) The rate of deoxidation is much more rapid at the beginning of exposure than at the end, a condition especially noticeable at temperatures around 900" C.; that is, deoxidaion is retarded as the depth penetrated by the reducing gas increases. (3) Within the accuracy of the experiments arsenic in copper up to 0.5 per cent. has no tendency to increase or decrease the action of a reducing gas on the cuprous oxide presenx in the copper. In 1912 pieces of 0.365-in. hard copper rod 1/2 in. long were heated in a porcelain tube in an electric furnace, while illuminating gas was passed through. An approximate analysis of this gas is: Hydrogen 38 per cent., carbon monoxide 30 per cent., illuminants 13 per cent., methane 10 per cent., ethane 3 per cent., carbon dioxide 3 per cent., nitrogen 2 per cent., oxygen 0.4 per cent. After heating for various lengths of time at various temperatures, samples were quenched

Jan 1, 1926

By E. T. Dumble

In continuation of the geological work begun in Sonora, Mexico, a partial account of which has already been given in the Transactions of the Institute,* a similar reconnaissance was made of Cochise county, Arizona, and a part of the Whetstone mountains. The investigation resulted in the identification of beds of similar age and character to those of the Sonora region, and in the discovery of interesting deposits, which, so far as I call ascertain from the literature at my command, have not been described heretofore. Route.—Starting from Nogales, we followed the railroad to Crittenden, and then drove to the southeastern slope of the Whetstones. After a brief examination of some reported coalbeds we continued our route, following the wagon-road between the Whetstones and the Mustang mountains to Huachuca, and eastward to Tombstone. Crossing the Dragoon mountains at South Pass, we traveled south and west by way of Turquoise and Antelope Spring into the road from Tombstone to Bisbee. Our route over the Mule mountains lay through Mule Pass and Bisbee, where we stopped a day or two. Thence, crossing Sulphur Spring valley, we drove around the southern end of the Swisshelms, and N. through the valley between these mountains and the Chiricahuas, to White river. From that point our way led through Rucker canon into the San Simon valley, then northward along the eastern face of the Chiricahuas, and by way of Fort Bowie to Willcox, Arizona, from which place we returned to Nogales. It was greatly regretted that the extremely wet weather prevented us from including in our examination the Huachuca

Jan 1, 1902

E. A. HOLBROOK,*Urbana, Ill.-To those who have followed the development of powdered coal two questions often occur. First, as to the moisture in the coal. In Illinois we recognize that the bituminous coals contain about 12 to 15 per cent. of what we call "contained moisture," that is, the moisture is present in the coal although this may appear absolutely dry and dusty. In addition, the surface moisture may be present in any amount. I would like to ask what is the relative effect of these two forms of moisture upon the work of pulverizing. Does Mr. Collins refer to the contained moisture or to the surface moisture in estimating the degree to which the coal must be dried? H. R. COLLINS.-In the lignite coals, of which this country possesses a great deal and is beginning to develop them to considerable extent, the "contained" or "combined" moisture does not .trouble us; we have no difficulty in reducing lignites to a high degree of fineness. But when dealing with bituminous, sub-bituminous, or semi-bituminous, we, prefer to reduce the combined moisture as well as the hydroscopic moisture as far as possible. We have recently put into operation, at a plant, furnaces and boilers consuming the lignite from northern New Mexico, which contains between 4 and 5 per cent. moisture as we pulverize and burn it. The evaporating efficiencies under the boilers have been so remarkable that we wish to check the results half a dozen times before quoting them. We have also just started two boilers at the Garfield smelter, and have obtained the same high efficiencies.

Jan 11, 1918

By E. W. Wagy

The year 1927 witnessed numerous developments of significance in California. The State's shut-in production increased from an average of 58,000 bbl. daily in January to a maximum of 93,000 bbl. daily in August, and a total of about 25,000,000 bbl. was withheld from the market during the year. This not only lessened the effect of large production at Hunt-ington Beach, Seal Beach and Alamitos Heights, but also was a most effective conservation move. Since 1922, it is estimated that approximately 100,000,000 bbl. of oil that would otherwise have been produced have been held in the ground. I. Outstanding Field Developments of 19271 1. Long Beach Deep Sand. 2. Rincon (Seac1iff)Discovery. 3. Alamitos Heights Discovery. 4. Ventura Avenue Extension. 5. Round Mountain Discovery. 6. Mt. Poso Extension. 7. Potrero (Cypress) Discovery. 8. Buttonwillow Gas Development. 9. Goleta Discovery. 10. Union Avenue, Edison and Fruitvale Areas. (See Fig. 1.) II. Crude Production The most important factor in new crude production in 1927 was the Seal Reach field with its adjacent Alamitos Heights townlot area. Production increased from about 10,000 bbl. daily in January, to a peak of 66,000 bbl. in June. Huntington Beach finished the year 1926 with a production of 102,000 bbl. daily, which declined to 60,000 bbl. by the end of 1927. Due to production in these three areas and the tempering effect of shutting in numerous wells, the California production curve for 1927 was held at a fairly even level. Fig. 2, shows the State's production in 1927 and 1926 as compared with 1923, which was the year of excessive

Jan 1, 1928

By A. W. Hesse

Twelve years ago, some coal-mine operators, mining engineers, oil and gas operators, Bureau of Mines engineers, geologists and state mine inspectors met in Pittsburgh, Pa. to discuss and solve if possible, the problems in connection with the drilling of oil and gas wells through or near coal mines and through the future coal reserves. Regulations were drafted and presented by O. P. Hood and A. G. Heggem of the Bureau of Mines.' . There was considerable discussion of the various articles, practically all of which appear in Bulletin 65, but the interest aroused at that meeting was short lived. Practically none of the important coal-producing states gave the matter the consideration it should have received. Notwithstanding the marked progress in safety work, coal mines still have an unenviable reputation for mine explosions. Our mining laws have become stricter and the enforcement, especially in Pennsylvania, more rigid, but what good will come from a rigid enforcement of the mining laws if some source of danger exists all around the mines, over which the operators have no control ? It is hardly necessary to recite all the cases of natural-gas explosions published in Bulletin 65, but with some of them I am especially familiar. In 1912, while visiting the Miners' Hospital, at Fairmont, W. Va., my attention was called to a patient swathed in in bandages so that no part of his face and hands were visible. He had not been told that his two sons, mere boys, had died of the burns they had received in the same accident—explosion due to natural gas leaking into a country mine at Peora, Harrison Co., W. Va.

Jan 1, 1925

By F. E. Calkins

THE following presentation of the more important accumulated facts and probabilities involved in copper ore deposition is based on my experience in examination work and study of the extensive litera-ture of the subject; to make personal mention of all sources of information would require the naming of a small army of able geologists and other investigators who have contributed to, building up the science. I have tried to present the salient features of the subject in logical order and condensed form, and to point out the relative importance of processes involved. Doubt-less many geologists could suggest some changes and many additions. ORIGINAL SOURCE The original source of all copper was in the earth's interior; it has been brought to the outer part of the earth, within reach of man, in three ways: (1) By intrusions and flows of basic igneous rocks containing copper in minute quantities, presumably as silicate or sulfide. No orebodies have been formed by this method. (2) As segregations within intrusive igneous rocks, the copper minerals having solidified at the same time as the rock itself. The few deposits known to have been formed in this manner have been of little or no importance. The oft quoted Sudbury nickel-copper deposits are now known to belong to the class following. (3) By gaseous or liquid aqueous emanations from ,large deep-seated masses of intrusive molten rock. These emanations, or mineral solutions, ascended through zones of connected openings in the earth's crust and dropped their load at points far above their source. Deposits formed in this manner were the primary source of nearly all, if not all, of the world's copper production.

Jan 10, 1923

By J. E. Clennell

IT is a common observation that the improvements introduced in practice since the first announcement of the cyanide process have been almost entirely mechanical. Although a good deal of study and research has been devoted to the chemical problems involved, the results obtained appear trifling in comparison. Few of the suggested modifications in the chemical treatment have come into practical use and those only in limited fields. Nevertheless, if we study the recent history of the cyanogen compounds from a somewhat broader standpoint, we shall find that considerable additions have been made, not only to our knowledge of their chemical properties, but also to their applications for industrial purposes. The present review of these advances naturally falls into two divisions: (1) processes involved in the treatment of ores; (2) manufacture of cyanides and other related compounds. PART I. ADVANCES IN THE CHEMISTRY OF ORE TREATMENT BY CYANIDE In the attempt to extend the scope of the process, various ores have been encountered which contain gold and silver in such forms that they will not yield satisfactorily to ordinary methods of cyanide treatment. . In some cases the difficulty is due to the excessive action on the solution of base metals present in the ore; in others, to the occurrence of minerals such as dyscrasite (the native alloy of antimony and silver), or a supposed oxidized manganese compound containing silver, which are either altogether insoluble in or very slightly attacked by cyanide. A particularly troublesome case is that of the so-called "graphitic" ores, containing carbon in some form which has the property of precipitating gold and silver already dissolved.

Jan 10, 1915

By L. O. Howard

TWO or three years ago there were submitted to me some reports of tests that had been made on a semi-oxidized ore of silver looking to its treat-ment by combined flotation and cyanidation, together with a sample of the ore, with a request that I check the tests and confirm them, if possible. These tests had been made by a machinery-supply house and with them was a flow-sheet for a proposed mill, with full details of equipment to be used in the mill. The limited data on which this was based at once attracted my attention and have caused me from time to time to put various groups of students at work to develop simpler methods of obtaining data, which it appeared should be at hand and could be obtained by simple tests before attempting to treat these ores commercially. A brief discussion of the working out of such methods may be of interest and may contribute somewhat to the de-velopment of better testing methods for the small operator who has not at his command a staff of metallurgists. Of several tests on samples of varying assay and mineralogical composition, by cyanidation alone, by flotation alone, and, by combinations of the two, the following report was perhaps the most complete and may well serve as a typical example: METALLURGICAL TEST REPORT Silver Mines Co. Semi-oxidized Ore Procedure: Ore ground to 65 mesh, given flotation treat-ment using pine oil and potassium xanthate. Flotation tailing was thickened and given cyaniding agitation in solution strength of 5 lb. cyanide per ton and 2 lb. lime per ton.

Jan 12, 1927

By W. F. Cloud

The data and information compiled under Part I of this report are the results of experiments performed in the petroleum engineering laboratory under the supervision of W. F. Cloud, Associate Professor of Petroleum Engineering and William Schriever, Professor of Physics, University of Oklahoma. Problems Being Studied Most of the time has been spent in trying to determine the rate of flow and pressure gradient in a 4-in. flow tube 10 ft. long, which was packed with sand of various grain sizes. To date, only two kinds of sand have been packed in this tube: 60 to 80-mesh Canadian river sand, 60 to 80-mesh and 80 to 100-mesh Simpson sand. The original intention was to follow the same procedure and use the same types of crude under identical saturation pressures of both air and gas, as well as unsaturated (dead) oil, flowing the various crudes through several different sizes of both Canadian river and Simpson (Wilcox) sands, but lack of time has prevented such an intensive study of the problem. Some additional time has been spent flowing saturated and unsaturated crudes, similar to those used in the 4-in. tube, through 1-in. tubes, one of which was 2 ft. long and one 5 ft. long. The results obtained have been checked against those obtained by using the 4-in. tube, to obtain the relation of diameter and length of tube to rate of flow in similar sands. Laboratory Equipment Saturation Tank.—A heavy steel cylindrical saturation tank, capacity about 42 gal. was mounted on a platform of bricks, then a galvanized tin temperature bath was built around the saturation tank. This contained

Jan 1, 1930

By J. W. Spretnak, G. Sachs

The: iron-rich iron-nickel alloys have attracted considerable academic interest in recent years. The carbon-free alloys are of minor practical importance, but they are the base of many alloys with various outstanding properties. The iron-nickel alloys, therefore, have been investigated extensively regarding both their structures and their properties. The researches on these alloys up to 1938 have been collected and critically reviewed by J. S. Marsh,l and will be discussed in some detail in the sections of this paper dealing with specific subjects. These numerous investigations have not succeeded in establishing the equilibrium conditions in this system. Alloys containing more than a certain amount of nickel (8 to 10 per cent Ni) undergo the allotropic transformation extremely sluggishly, both on heating and cooling, showing a large hysteresis," which is not dependent upon the rate of cooling and persists even with very slow rates of cooling.3 Honda4 and Merica4 have therefore resigned themselves to proposing a diagram (Fig. I) for practical use, illustrating the structural relations under commercial conditions instead of attempting to establish the true equilibrium diagram. Marsh is less pessimistic and suggests an equilibrium diagram (Fig. 2) which conforms approximately to the facts known about this system. Recent X-ray investigations by Owen-Sully5 and Bradley-Gold-schmidt6 on powdered alloys indicate that the previous work on the iron-nickel system yielded very incomplete results. These investigators agree (Figs. 3 and ,+) that alloys in the powdered form containing more than 8 per cent and up to about 35 per cent Ni decompose into a stable heterogeneous mix-

Jan 1, 1941

By G. Sachs, J. W. Spretnak

The: iron-rich iron-nickel alloys have attracted considerable academic interest in recent years. The carbon-free alloys are of minor practical importance, but they are the base of many alloys with various outstanding properties. The iron-nickel alloys, therefore, have been investigated extensively regarding both their structures and their properties. The researches on these alloys up to 1938 have been collected and critically reviewed by J. S. Marsh,l and will be discussed in some detail in the sections of this paper dealing with specific subjects. These numerous investigations have not succeeded in establishing the equilibrium conditions in this system. Alloys containing more than a certain amount of nickel (8 to 10 per cent Ni) undergo the allotropic transformation extremely sluggishly, both on heating and cooling, showing a large hysteresis," which is not dependent upon the rate of cooling and persists even with very slow rates of cooling.3 Honda4 and Merica4 have therefore resigned themselves to proposing a diagram (Fig. I) for practical use, illustrating the structural relations under commercial conditions instead of attempting to establish the true equilibrium diagram. Marsh is less pessimistic and suggests an equilibrium diagram (Fig. 2) which conforms approximately to the facts known about this system. Recent X-ray investigations by Owen-Sully5 and Bradley-Gold-schmidt6 on powdered alloys indicate that the previous work on the iron-nickel system yielded very incomplete results. These investigators agree (Figs. 3 and ,+) that alloys in the powdered form containing more than 8 per cent and up to about 35 per cent Ni decompose into a stable heterogeneous mix-

Jan 1, 1941

REGULATIONS (proposed) for the location, drill-ing, casing, protection, operation, plugging and filling, and abandonment of natural gas and petroleum wells; having for their objectives. the protec-tion of life and property by prevention of intrusions of oil and gas into workable coal beds, and the conserva-tion of oil and gas resources in territory not underlain with workable coal beds. ARTICLE I Definitions Section 1.-For the purpose of these regulations (proposed), definitions are as follows: Well.-A bore-hole drilled for the purpose of developing natural gas or petroleum, or a bore-hole producing natural gas or petroleum. Well Operator.-Any person, persons, firm, partnership, corporation, company or association that proposes to, or does drill, operate, or abandon a well as herein defined. Coal Operator.-Any person, persons, firm, partnership, corporation, company or association that proposes to, or does operate, a coal mine in territory known or reputed to be underlain with oil or gas-bearing strata. State Mining Department.-The duly constituted authorities of a state having jurisdiction over coal-mining operations. Plat.-A map, drawing, or print made in accordance with the pro-visions of these regulations (proposed). Casing.-The pipe greater than 3 in. in diameter commonly used in wells drilled for natural gas and petroleum. Oil and Gas.-Synonyms, respectively, for petroleum and natural gas. Cement.-Hydraulic cement properly nixed with water only. Workable Coal Bed.-A coal bed in which, in the united judgment of the coal operator, the well operator and the State Mining Department, protection for life or property will be required when wells are drilled through it.

Jan 7, 1927

By Sidney A. Swensrud

The writer has been interested for some time in trying to appraise our industry's prospects for gasoline consumption over the next half dozen years or so. Anyone who has even approached the problem knows the intimate relationship to it of the number of automobiles in use— by automobiles I mean both passenger cars and trucks. Probably at least 90 per cent of our gasoline is used in automotive vehicles. Some recent estimates secured from the Department of Commerce show the following breakdown: Per Cent Passenger cars............................................ 60.0 Trucks................................................... 27.4 Busses................................................... 2.9 Taxicabs................................................. 2.2 Subtotal............................................... 92.5 Aviation, motor boats and railroads......................... 0.5 Agricultural: farm tractors, etc.............................. 3.3 Balance (manufacturing, government use, construction, etc.)... 3.7 100.0 Up to the beginning of the depression there was, of course, a constant annual increase in the number of automobiles in use, for each year the industry added to the total inventory or ''population" more new units than were being scrapped, as may be seen in Fig. 1. Few of us in the oil industry needed to give much attention to the detailed figures, although the automobile industry seemed to interest itself in all sorts of calculations of replacement demand vs. new car demand, the average life of the car, the number scrapped, and the like. Probably many people in the oil industry, as well as outside it, were surprised at the way in which automobile registrations and gasoline consumption held up during the early years of the depression. Nor were they greatly perturbed when, as in the last two years, both registrations and consumption began to fall somewhat. That was natural enough; it

Jan 1, 1933

By W. R. Toeplitz

Probably a more descriptive title would be "Much Ado About Nothing." By "nothing," of course, I refer to the porosity which is the main feature of this type of bearing. Porosity has a decided effect on the manufacturing techniques, the structure and physical properties, the oil content, and on the installation and service of oil-retaining porous bronze bearings. A simple curve can be drawn by plotting specific gravity along the abscissa and percentage of porosity by volume on the ordinate. A bronze composition, analyzing 89 Per cent copper, 9.75 Per cent tin, and 1.25 per cent graphite, has an absolute solid specific gravity of 8.5. At this specific gravity, of course, occurs the point of zero porosity. Conversely, at loo per cent porosity, the specific gravity is zero. A similar curve can be drawn for bearings impregnated with oil; the only change being that the specific gravity at loo per cent oil will be 0.89 if we assume that that is the specific gravity of the lubricant. The curve is useful in determining the oil content by volume for any specific gravity. The normal range of oil content for porous bronze bearings of this composition is from 35 to 16 per cent, which is in the specific gravity range of from 5.8 to 7.3. In addition to the amount of porosity, the type of porosity is important. The first consideration here is that the porosity must be intercommunicating. This can be determined by a number of simple tests. The first method, which is very accurate, is to extract the oil in the bearing by cycling

Jan 1, 1945

By R. J. Armstrong, J. J. McKay

The Montana Phosphate Products Co. is currently operating three underground phosphate mines in Powell County, MOnt. † In this area the Phosphoria formation is from 35 to 50 ft thick and contains a bed of phosphate rock varying in thickness from 2 1/2 to 5 ft, overlain by 12 to 30 ft of cherty quartzite, and underlain by about the same thickness of quartzite and shaly to cherty beds. In general, the phosphate bed has a reasonably hard quartzite footwall, as well as a hard cherty hanging wall, both of which greatly facilitate the mining operation. Folding has deformed the phosphate bed to a considerable degree in the area. It is carried to surface by several of the anticlines and lowered to considerable depths in some of the syn-clines. The main structural features affecting the mining operations of the company are the Garrison anticline and the adjoining syncline and succeeding limb of a second anticline on the east (Fig I). The axis of the folding strikes roughly northwest-southeast. The three mines, namely, the Anderson, Graveley, and Luke are on different limbs of the above folds. Accordingly, the dip of the bed, and consequently the mining method, in each mine differs to a considerable degree from that of the others. For this reason, each operation will be dealt with separately. Anderson Mine LOCATION AND DEVELOPMENT Topographically this mine is in a narrow valley, the bottom of which has an altitude of 5200 ft. The phosphate bed outcrops near the ridge on the east and dips towards the valley floor at an angle of from 25 to 30°,

Jan 1, 1950

By Charles Albert Ashburner

Natural gas has been known to exist for many years in the St. Lawrence Valley, between Quebec and Montreal, and more partirularly in the vicinity of Louisville and Three Rivers, 74 and 94 miles respectively northeast of Montreal, and 98 and 78 miles respectively southwest of Quebec; the distance from Montreal to Quebec along the St. Lawreuce River being about 175 miles. It was not until 1880 that any practical explorations were begun with the hope of finding gas in sufficient quantities for commercial uses. In this year Messrs. Piret and Genest, of Three Rivers, sank a well near St. Maurice to a depth of 50 feet, where solid rock was encountered. A similar well was drilled through the glacial and allavial drift, in the same district, in 1883, by the Messrs. Renaud Freres and Dubois, to a depth of 70 feet before solid rock was encountered. In this latter well a strong flow of gas was obtained. The gas was an outflow from a very limited reservoir in the porous glacial gravel, which had been filled from the gas resulting from the decomposition of vegetable remains, which had been buried in the gravel at the time of its deposition. Subsequently, other wells were sunk in the same way, with the hope of getting gas in commercial quantities from similar reservoirs. Commercial Gas.—By gas in commercial quantities I mean gas in such quantity that, if utilized with proper care and economy, it would generate steam at a cost below the cost at which the same duty could be obtained from the use of coal or wood at current prices, and that

Jan 1, 1890

By Charles H. Eldridge, Robert J. Anderson

When a metal or alloy is poured into a mold, internal stresses are set up by the cont,raction in volume on passing from the liquid state at the temperature of pouring to the solid state at the ordinary temperature. It is assumed by the writers that all castings are internally stressed. That any casting is internally stressed is shown by its warping or distortion on maturing at the ordinary temperature, by warping or cracking on heating, or by cracking or distortion on machining. In the investigation made by the writers, the internal stresses in cast non-ferrous alloys were studied with a view to examining the effects of heat treatment (i.e., simple anneal) on the release of such stresses. Data have been obtained that show quantitatively that internal stresses can be removed by appropriate heat treatment. The investigation was limited to a study of the effect of heat treatment on stress release in cast rings of the 87:7:5:1 copper-tin-zinc-lead alloy. The writers are indebted to E. G. Fahlman for the method used for inducing stress in cast rings; to M. E. Boyd for microscopic examination and for other aid; and to G. B. Dalrymple for the chemical analyses. General Information While casting stresses have been discussed considerably, they have usually been treated in a general way, and so far as the writers know no measurements of the magnitude of internal stresses in castings have been reported. It has been suggested by many investigators, particularly in the case of steel castings, that castings are internally stressed, and that these stresses can be removed by annealing. In a casting, the internal

Jan 1, 1923