Search Documents

By James A. Roberson

THE mechanical behavior of molybdenum has become a matter of considerable interest in recent years because it has a reasonably high strength at high temperatures. Various aspects of its fatigue behavior have been investigated previously,1-3 and the results can be summarized as follows. Recrys-tallized molybdenum exhibits a fatigue limit which decreases continuously with increasing temperature. The ratio of fatigue-limit stress to ultimate tensile stress is high (0.6 to 0.8) and reasonably constant. The present work was undertaken to determine the effect of variations in environment on the fatigue of molybdenum stressed in fully reversed axial tension compression. In order to provide a basis to which these data could be compared, a complementary series of fatigue tests were made in vacuum. All of the specimens used were made from one mill lot of unalloyed molybdenum which had been vacuum-arc melted, worked down to 1-in.-diam bar, re-crystallized, then warm-worked to 5/8 in. diam. The interstitial content by weight was as follows: C—0.022 pet, 02-0.0026 pet, Hz-0.0001 pet, and N20.0002 pct. The average grain diameter in the transverse direction was about 0.035 mm, and the average grain length was about 0.15 mm. Typical tensile-test data are shown in Table I. None of the specimens tested exhibited an upper yield point.

Jan 1, 1965

By R. C. Gifkins

R. C. Gifkins (CSIRO)—In this paper evidence is put forward to support the idea of grain boundary shearing in aluminum at 4.2°K and the phenomenon is explained in terms of a low-temperature "equicohesive temperature". It is stated that these findings show that grain boundary shear cannot be ruled out in any situation by temperature arguments alone. We believe, from our own recent study of "apparent grain boundary sliding'' at temperatures below 0.45 Tm, that it can be ruled out on temperature arguments alone.45 Our experiments were made principally with magnesium and a Ms-A1 alloy ("Magnox A12"). Careful examination of offsets of marker lines or steps at grain boundaries produced by deformation at room temperature (-0.3 Tm) showed many of these to result from curvature over narrow zones along the grain boundaries. A significant residuum did, however, appear as a sharp offset or step. It was found that the mean value of this step rose to a small value during the first 0.5 to 1 pct strain and then remained at this level with further strain. Moreover, exactly the same values were obtained (at the same stress) at 75°C instead of 21°C. That is, in this range of temperature the "apparent sliding" was not temperature-sensitive. At 125°C and above there was sliding which increased with strain and which was temperature-dependent. When this temperature-dependent sliding was used to calculate the sliding to be expected at room temperature, this underestimated the "apparent sliding" by a factor of 104. The conclusion drawn is that the "apparent sliding" consists of shear localized in a zone of a width measured perhaps in microns, whereas it seems that true sliding occurs on the boundary surface.46 A model for such localized shear has been developed in general terms, following a similar model of Urie and Wain.47 Other strong evidence for low-temper- ature sliding has been based on the offsets of marker lines consisting of a substructure seen using the electron microscope to resolve these.48 We have repeated this work and found that the effects can be accounted for in terms of cracks in an oxide film which is produced when the substructure is etched up; these cracks form over zones of shear rather than at actual interfaces. However, in aluminum at room temperature (-0.3 Tm) there is no "apparent sliding" which is optically detectable. We suggest that, when the temperature is much lower (and possibly the rate of strain higher, too), as in the experiments of Chin et al., then aluminum behaves like magnesium at room temperature, and a narrow zone of shear develops to accommodate differences in strain across the grain boundary. Such a zone could well give rise to triple-point cracks. It is hoped to investigate these suggestions further. B. Y. Chin, W. F. Hosford, Jr., and W. A. Backofen (authors' reply)—It is interesting to have Dr. Gif-kin's comments, although it is somewhat difficult to reply in detail without the reference containing the work that he describes. Apparently though, he does find a low-temperature temperature-independent sliding that would seem to be related to the observations reported here. Perhaps some of the difficulty has semantic origins, growing out of the distinction between ('true sliding" and "apparent sliding".

Jan 1, 1965

The Goodman Mfg. Co., Chicago, builders of underground electric mining machinery, celebrated its 50th Anniversary on April 23rd. The company has a complete line of cutting machines, loaders, conveyors, locomotives, and shuttle cars for service in both coal and metal mines. The Joy Mfg. Co. has received, under the provisions of the Economic Cooperation Administration, an initial order in excess of $1,000,000 for equipment to be used in the mechanization of iron ore mines in France. While the equipment will be used in various privately owned mines, the order was placed through the French Society for the Development of Mechanical Mining. Included in the equipment are the company's recently developed hard rock loaders and shuttle cars. American Brake Shoe Co. has consolidated all operations of its Canadian subsidiaries into one corporation, the Dominion Brake Shoe Co. Ltd., Montreal, Canada. The products of Dominion Brake Shoe include brake shoes, track equipment, manganese steel castings, automotive brake lining, air compressors, and paint spray equipment. Exhibits of more than 2000 electrical products, processes, and techniques, ranging from precise aircraft instruments to complex working models of steel mill, textile and other industry equipment, will be displayed in the "More Power To America Special" when it makes its nationwide tour this spring. C. H. Lang, Vice-President in charge of sales for General Electric's apparatus department, said that the train will visit the country's key industrial centers for inspection by utility and industrial executives and municipal leaders. The train will be hauled by an Alco¬G-E two-unit, 4000-hp., Diesel-electric locomotive which in itself will be part of the unusual series of displays. Sizing of Excavators and Hauling Equipment. The Power Crane and Shovel Association has released a 24-page bulletin dealing with the proper sizing of excavators and hauling equipment, Technical Bulletin No. 3. Rubber Conveyor Belting. "Installation, Care and Maintenance of Rubber Conveyor Belting" is the title of a booklet just published by the Carlyle Rubber Co., New York. Power Transformers. The manufacturing procedure of Allis-Chalmers small power transformers is described in a new 28-page bulletin, 61B6094A, covering the core and coil unit, no-load tap changer, tank construction, cooling methods, oil preserving systems, bushings, terminal compartments, indicators and testing of transformers. Safety Equipment. General Scientific Equipment Co., Philadelphia, has released a 46-page, fully illustrated catalog on personal protective equipment and industrial safety devices. This new catalog covers respiratory devices, eye protection, hats, gloves, carboy pumps, drum pumps, and miscellaneous safety equipment for use in mines, industries, etc. Osmosalts. The Osmose Wood Preserving Co., Buffalo, N. Y., has issued a bulletin on Osmosalts, the wood preservative which, say the manufacturers, makes timber last three to five times longer, slashes maintenace costs, stops rot, and resists wood-destroying insects. Jigs. The Dorr Co. has acquired the Pan American jigs and they are now known as the Dorrco-Pan American jigs. Originally developed as a gold-saving device for dredges, the simplicity, ease of operation. efficiency, and negligible maintenance of these jigs have resulted in wide adoption on all types of placer operations, in the closed grinding circuits of gold mills, and on many applications where a coarse bed concentrate is separated from the ore gangue.

Jan 5, 1950

By J. C. Scully

In June, 1965, Sanderson and scully5 reported at the Conference on Environment Sensitive Mechanical Properties of Materials at the Research Institute for Advanced Studies at Baltimore that thin foils of titanium could be prepared by chemical polishing in a mixture of 44 pct HF and 73 pct HNO3 in the volumetric ratio 2:3. The technique is simpler than that since reported by Rice and Orava. As-received annealed titanium (containing 0.8 pct Fe and 30 ppm H) in the form of sheet 0.05 cm thick is placed in the solution and moved up and down. The reaction is violent but suitable foils are obtained very easily and consistently. A typical micrograph is shown in Fig. 3. The small precipitates were not identified. Yamane and ueda6 observed many spotlike features which they referred to as small dislocation loops. While their spots may be due to the reaction of the warm foil with the air as suggested by Rice and Orava, the precipitates in Fig. 3 are also found when foils of titanium are prepared by electro-polishing at low temperatures and subsequently examined in the electron microscope without any inter- mediate warming. Furthermore, they are not a surface effect. It is necessary to add that alloys of titanium cannot be so easily thinned by the chemical polishing solution described above since it contaminates the a, phase with hydrogen and produces y hydride. These matters are described at length in a paper7 and their relevance to stress corrosion is considered elsewhere.'-* Author's Reply The authors are grateful to Dr. Scully for bringing to our attention his hitherto unpublished technique for thinning unalloyed titanium, and deeply regret the unintended apparent duplication. The chemical thinning solution (7 parts HNO3 and 3 parts HF, by volume) reported by us is the same as that with which, for some period in the past, we had experienced success in the preparation of foils from single and polycrystalline niobium. Its subsequent effective application to titanium was a logical step, which, clearly independently of Scully, was conceived by Mr. Rice, to whom full credit is due. A few comments are warranted concerning some of the details of the preceding Discussion. It is evident to the discerning reader that the two thinning techniques under consideration are chemically almost identical, and in that sense are equally "simple". The chemical aspect is, of course, the one of primary importance in both communications. Thereafter, the relative simplicity is dictated by the mechanics of the actual thinning operation selected by the individual investigator. Our standard dimpling, or dishing, procedure was chosen with a view toward providing, for the electron transparent areas of the sample, the maximum protection from extraneous deformation during handling. That the long, straight dislocations visible in Scully's electron micrograph of a seemingly recovered structure closely resemble handling dislocations would tend to indicate the merit of our adopted technique. Features similar to those which Scully has attributed to precipitates, without any apparent diffraction contrast confirmation, were not observed in any of our clean foils taken from annealed or deformed specimens. This was admittedly somewhat surprising since the 3700 ppm (nominal) Fe in the A-70 commercial-grade titanium examined should have given rise to TiFe precipitates. Presumably these existed but were un-resolvable. Curiously, Scully's "precipitate1' density is fairly high although the iron content quoted was less than one-fourth of that in our material. One is forced to conclude from the evidence that prior thermal and mechanical treatments are responsible for the two different types of structure observed.

Jan 1, 1968

By R. W. Raymond

In a paper on the Divining-Rod (Transactions, xi., 411), presented at the Boston meting, in February, 1883,I suggested, among other signs of which the skilled prospector might consciously or unconsciously avail himself in the search for springs of water or mineral deposits, the presence of particular grasses or shrubs, and the general appearance of the flora. There are not wanting, in the literature of our art, indications that greater attention was paid to such signs in ancient days than at present. It is the tendency of a scientific age to ignore, or regard as superstitious, what cannot be classified or explained. But the acute though unscientific observation of earlier times often, doubtless, accumulated facts which it would be worth our while to re-examine. It is highly probable that the mining prospectors of the sixteenth and seventeenth centuries, to go no further back, were close students of nature, and knew, though they could not explain, and, for reasons of private gain, would not communicate, many curious and significant facts. We can generalize better than they could; but for that very reason we are, perhaps, their inferiors in observation. They let nothing pass, because all things were equally significant to them. We take wider views, and miss more. And, no doubt, there still exists among practical millers, prospectors,, hunters, Indians, etc., an unwritten.

Jan 1, 1887

All the TECHNICAL PUBLICATIONS and PREPRINTS published in 1932 are available at Institute headquarters. They are also on file in public,, university and technical libraries and, when so indicated in the list, may be found in the TRANSACTIONS. Copies of the TECHNICAL PUBLICATIONS have been mailed to those members of the Institute who are registered in the different classes: A-Metal Mining; B-Milling and Concentration; C-Iron and Steel Division; D-Nonferrous Metallurgy; E-Institute of Metals Division; F-Coal Division;. G-Petroleum .Division; H-Nonmetallic Minerals; I-Mining Geology; K-Mining Administration; L-Geophysical Prospecting. Other members may obtain copies by writing to the Secretary. Copies of PREPRINTS may also be obtained from the Secretary's office. Additional copies are sold at the rate of 1 cent per page; minimum charge, 25 cents. Nonmembers may purchase the papers at the prices mentioned. METAL MINING TECH- NICAL PUBLI- - TITLE AUTHOR MEETING TRANS. CATION VOLUME No. AND PAGE* 484-A.45 Propeller Type Mine Fan at Moose A. S. Richardson New York 102, 86, 93 F.52 Shaft, Butte, Montana (13) Feb., 1932 487-A.46 Progress in the Improvement of Max H. Barber New York, Methods and Equipment at Feb., 1932 Open-pit Iron Mines on the Lake Superior Iron Ranges (9) Pre. Sand Filling through Pipes and Lucien Eaton New York, 102, 33, 41 Boreholes (9) Feb., 1932

Jan 1, 1932

By Raymond H. Young, Paul Sennett

INTRODUCTION Kaolin clay, consisting largely of the mineral kaolinite, is widely used as a white pigment. In the United States, for instance, pigment kaolin production was nearly 6,000,000 tons in 1976 (1). Production for this year should be significantly above this level. Current prices for kaolinite 'pigments range from about $20.00/ ton to$260.00/tony,depending on the amount of processing needed to make the final product. Although much of this pigment kaolinite is used as an inert filler where product specifications are not very rigid, a large quantity of kaolinite is converted to products where very restrictive specifications exist. These specifications set severe limits on such properties as viscosity in a water suspension, particle size distribution, color, and brightness. This discussion will concentrate on methods available to improve the color and brightness of pigment kaolin and will review the advantages and problems associated with these various methods. The term "brightness" refers to the reflectance of the pigment to blue light (2). Since even the brightest commercial kaolins have a somewhat yellowish color, the blue reflectance (or brightness) is a reasonably good measure of their nearness to a perfectly white material. I KAOLINITE STRUCTURE AND SOURCES The mineral kaolinite is an aluminum silicate and can be represented by the formula (OH) 8Si4A14010. The formula is frequently written

Jan 1, 1979

By Henry S. Poole

This field is geologically of much interest. It is small, hut with some seams of unusual thickness, the main one being as much as thirty-eight feet thick. The quality of the seams, as also of the associated beds of shale and sandstone, in several instances changes to a remarkable degree within short, distances. The strata dip at inclinations that carry the coal to depths of 3000 feet or more; heavy faults cut up the district, and the New Glasgow conglomerate, of disputed age, separates it from the Upper Carboniferous measures, in which no seams of workable thickness are known. This coal-field offers to the geologist much ground for study and peculation. The commercial value of the field is affected by its restricted area, the varied quality of its coal, and its advantageous position in the mainland, with railway connection and home markets, offset by the physical difficulties which make the cost of production high. It has been so long a habit with us to speak of our resources of coal as boundless, that any adverse comments, or insinuations that avoidable loss in working is a national loss, hare hitherto fallen on idle ears. While it is not my purpose to underrate the riches we do possess, yet I deem that no good end is served by echoing exaggerated estimates which encourage a national indifference to wasteful

Jan 1, 1886

By Franklin R. Carpenter

Pyritic smelting, so-called, as practiced in the Black Hills is pyritic smelting only in the sense that Dr. John Percy uses the expression in his " Metallurgy of Silver," where he describes a process for smelting dry silver-ores in connection with iron pyrites, to form a regulus. The ores treated by this process in the Black Hills are very siliceous, averaging about 74 per cent. of silica, from 10 to 20 of iron oxide, 4 or 5 of alumina, and from 2 to 4 of lime. In 1889, while Dean of the South Dakota School of Mines, I took up the question of their smelting. There were neither copper- nor lead-ores in the Hills; hence pyrite and pyrrhotite, of which there are large deposits, were employed to form a regulus. This mixture of pyrite and pyrrhotite, besides being absolutely barren of gold and silver, carried an average of 30 per cent. of silica. The only basic material available as a flux for the great excess of silica in the ores and in the pyrite was a dolomitic limestone. Moreover, the local coke gave 24 per cent. of ash, 60 per cent. of which was silica—as unpromising a set of conditions as can well be imagined. We had before us the examples of Mr. W. Lawrence Austin, of this Institute, who had experimented at Toston, Montana,"

Jan 1, 1901

By T. A. Rickard

In " The Genesis of Certain Auriferous Lodes "* Dr. Don makes a reference to a curious vein-formation known as the "Indicator," which characterizes a portion of the Ballarat mining district,, in Victoria, Australia. During 1890 and again in 1898 I had an opportunity of making a few notes, which, although somewhat belated,t may be worth adding to the observations recorded in the Transactions of the Institute. The country of the Ballarat gold-field consists of the Lower Silurian slates and sandstones, which also enclose the reefs of Bendigo; but it is noteworthy that the successive anticlinal folds, and accompanying saddles of quartz, which distinguish Bendigo are not characteristic of Ballarat, the geological structure of which presents greater complexity. That part of the district known as Ballarat East became famous early in its history on account of the large nuggets which were found in the alluvium, and subsequently it became further known because of a peculiar persistent black seam, traversing the bed-rock underlying the alluvial deposits, which was found to be associated with rich bunches of gold-ore, not only in the gravel that capped it at the surface but also in the quartz-veins which crossed it underground. The name of " Indicator " was early given. In 1871 Mr. Morgan Llewellyn directed attention to it as influencing the distribution of the gold. In the government quarterly report for December, 1888,

Jan 1, 1901

By Paul E. Queneau, H. J. Roorda

Cobalt consumption will increase during the next decade at an average rate at least equal that of nickel. In the past, use of cobalt has at times been curtailed by lack of availability or by high price. In the future, output of cobalt derived from copper ores and iron sulfides will continue to grow and output of cobalt from nickel ores will be greatly increased. There should therefore be an adequate supply of this metal at a reasonable price. Nickeliferous limonites constitute by far the largest known terrestrial reserves of cobalt. A process has been conceived, based upon selective reduction and aqueous chlorination for treatment of such ores. The proposed procedure permits good extraction of the ore's cobalt content, comparable to that of the nickel, and is adaptable to large-scale, automated unit operations. Chlorine leaching of the ore enhances its value as a potential source of iron and chromium. Over four thousand years ago, cobalt pigments were employed for decorative purposes in some glass and glazes of Egypt and Persia, and by 1000 B.C. they were widely used in the Middle East.' " However, prior to 1914, virtually no cobalt was produced as metal and ceramics remained the largest consumer of the element as oxide. During World War I cobalt-containing high-speed steels came into their own and the metal's merit in magnet steels was established.

Jan 1, 1971

By John Hays Hammond

This is an era of "expansion;" and, conformably with the change in commercial conditions, the function of the mining engineer, as well as that of his confréres in many other professions, has also expanded. From the position of an engineer, limited to the determination of technical questions, the engineer of to-day has come to assume an economic importance in those branches of industry dependent upon engineering skill for their development. He is indeed an engineer of limited usefulness who does not go further professionally than to submit a purely technical report on subjects presented for his consideration. While he has the same responsibility as formerly in the solution of the technical problems involved, he is further expected to supplement his report with advice on the financial and commercial aspects of these problems. For the great majority of problems presented to the engineer ultimately involve the determination of the pecuniary relations of the propositions under consideration. The great corporation lawyer no longer earns his fee by merely submitting his opinion as to the legal issues involved in law-suits affecting the corporation; he now assumes charge of the entire legal work, including both the organization of the corporation and the maintenance of its legal status thereafter. In like manner, the engineer, whose report was, as I

Jan 1, 1909

By James W. Neill

The occurrence of minerals of nickel and cobalt at Mine La Motte is probably known to every mineralogist. I will not attempt to describe these minerals, but, before entering on my subject, will briefly mention the ores, etc., which call for metallurgical treatment and enter into the composition of our mattes. Our staple lead-ore, the dressed galena, is the chief source of nickel and cobalt. It carries but a small percentage of these metals, viz.: 0.2 to 0.3 percent. usually, though when much copper pyrites is contained in the gangue, the amount of nickel and cobalt may be as great as 1.0 to 1.5 per cent. Next in importance is the ((middle product" of the dressingworks, consisting of the sulphides of iron (and copper) with gangue and galena. This usually carries 20 to 23 per cent. of lead, 0.5 to 1.0 per cent. of copper and 2.5 to 3.5 per cent. of nickel and cobalt. A larger percentage of copper always carries with it an increase of nickel and cobalt. In some few cases 12 to 15 per cent. of copper gives 6.5 to 8.0 per cent of these metals. Resides these products of the dressing-works, there is a small quantity of true nickel-cobalt-ore

Jan 1, 1885

By Mark L. Requa

During the past two years California has developed a new and important oil-field: I refer to Midway. This field produced the famous Lake View gusher, which is credited with a total production in excess of 8,000,000 barrels. Fortunately for the oil industry of the State, this well is now a thing of the past, and nothing, save a great crater-like opening marks its location. The pipe is entirely worn away and gone; and it is a matter of serious doubt if there can be anything done that will cause the well to produce again. Fortunately, also, there have been no other wells in that field or elsewhere throughout the State that in any may compared with the Lake View. Midway is noted for large wells, of from 500 to 2,000 barrels production; but the decline is rapid, and a few months serve to bring the output down to a few hundred barrels. In the oil-territory heretofore blocked out as proved and probable, there have been, during the year, many changes. Some areas which were expected to be fairly productive have apparently failed; others, more strictly "wild-cat," have come in; while in some of the older fields there are properties which are beginning to shorn evident signs of exhaustion. The total area of proved territory will therefore probably suffer but small

Jan 1, 1912

By Bernard Kopelman, C. C. Gregg

THE reduction of tungstic oxide to tungsten metal powder by hydrogen is a process by which one might expect the resultant metal powder to be porous. In- [ ] deed, sponge iron, prepared by reduction of the oxide in a reducing gas, is generally accepted as quite porous, with pores large enough to be seen readily under the optical microscope at relatively low magnifications. However, any pores that may exist in tungsten metal powder are not resolved by the optical microscope, and apparently, not even by the electron microscope. Fig I shows commercial tungsten powder magnified at 10,000X by the electron microscope,1 both etched and unetched. In an earlier paper by one of the authors,2 the existence of pores in tungsten powder [ ] was required to explain adequately the particle size changes occurring during the reduction of tungstic oxide. The inability to detect these pores under the electron microscope at 10,000 X implies that these pores are of a size of 100 A units or less. (This in itself is by no means proof that pores above 100 A would not exist, since polishing effects on the specimen might smear up holes of such small magnitude). If, then, these pores are less than 100 A, and of the order of molecular size, then the density of the metal powder should be

Jan 1, 1948

By C. R. Van Hise

[Concluding Contribution of Prof. Van Hise to the Discussion of his Paper, and Others on the Same General Subject, presented at the Washington Meeting, February, 1900 (see Ram., xxx., 27, 177, 323, 424, 578) ; also of the contributions of Vogt, De Launay, Beck, Lindgren, Kemp, Rickard, Bain, Keyes, Collins and Adams, presented at the Richmond Meeting, February, 1901, and to be printed in the present volume.] In June, 1900, shortly after my paper was published in the Fransactions, I made a briefer statement* before the Western Society of Engineers covering the same ground, which, in certain respects, is somewhat of an improvement. For instance, instead of using the terms descending and ascending &th reference to the waters resulting in the two concentrations, my modified statement is as follows: " The first concentration of many ore-deposits is the work of a relatively deep water-circulation, while the reconcentration is the result of reactions upon an earlier concentration through the agency of a relatively shallow water-circulation. Commonly the deep water-circulation is lacking in free oxygen, and contains reducing agents, and the shallow water contains free oxygen. The deep water is therefore a reducing, and the shallow water an oxidizing agent."† Of the papers upon ore-deposits which, in vol. xxx. of the Fransactions, follow my own, or which were presented at the Richmond meeting, a considerable number are wholly con-

Jan 1, 1902

By AIME AIME

THE Hazleton district of the Pennsylvania Anthracite Region will be the scene Oct. 14 and 15 of the fall meeting of the Coal Division and the Pennsylvania Anthracite Section. Here, coal mining has been active for more than 100 years and hereabouts industrial necessity inspired the numerous inventions of the Pardees, Eckley B. Coxe, a former A.I.M.E. president, and the Marltles, who contributed much to the success of the Institute in its early days, as well as to the upbuilding of modern methods in the anthracite and bituminous industries. Headquarters will be the Altamont Hotel, Hazleton, Pa. There will be two technical sessions Friday, registration preceding the first which is scheduled for 11 a.m. to 1 p. m. The second will be called at 2:30 p.m. Saturday is reserved for mine and plant visits, with golf and tennis after luncheon for those so inclined. The ladies are cordially invited to the meeting and arrangements have been made for their participation in much of the program. The chairmen of the committees preparing for the meeting are: Donald Markle, president, Jeddo-Highland Coal Co., General Committee; R. E. Hobart, mechanical superintendent, Lehigh Navigation Coal. Co., Committee on Visits and Inspections; H. D. Kynor, general manager, Northumberland Mining Co., Committee on Programs and Papers; B. H. Stockett, general manager, Weston; Dodson, Inc., Reception Committee.

Jan 1, 1932

By Philip D. Pearson

Competition is the problem and modernization is the solution in today's underground iron operations on the Lake Superior Range. Profound changes in the iron ore picture during recent years have prompted correspondingly great changes in the economic position of the Lake Superior underground mines. To meet the ever growing competition from other lower cost iron sources, underground operators are becoming increasingly aware that the newest advancements in mining technology must be incorporated in their operations. UNDERGROUND POSITION TODAY The extraction of iron ore by underground methods has been going on for many decades in the Lake Superior region, starting in 1872 on the Menominee Range. The number of mines has changed gradually over the years as new ones were opened and old ones were exhausted, but in recent years, the most drastic change occurred from 1960 to 1961. In 1960, there were 31 underground mines operating in Michigan, Minnesota and Wisconsin, but at one period in 1961 only 20 were operating (Table I). In western Ontario so far there has been only some temporary curtailment of operations. Of the 11 U.S. mines which ceased operations in 1961, some may he closed only temporarily, but some will remain closed for our lifetime, at 'east, unless there is a tremendous reversal of the present trend in the iron ore market

Jan 3, 1962

By M. Vallée

This case study compares the actual production figures for the No. I and No. 2 copper orebodies of the Société Miniére Louvem, Val d'Or, Quebec, with the preproduction estimates and a postmortem geostatistical estimation using kriging techniques. The deposits considered are small subvertical sulphide orebodies which were mined from August 1970 to April 1973, producing 648,000 tons at 2.04% Cu versus the 1968 computed reserves of 671,000 tons at 2.51% Cu (with 20% dilution), thus showing a 25% overestimation of the copper contained. The postmortem geostatistical estimation based on the same 44 D.D.H. intersections available in 1968, shows 2.24% Cu (no dilution), compared to 3.23% Cu (no dilution) given by the conventional section method. Block by block kriging techniques were used, but within the ore contours as determined by the geologist. In this case, Characterized like many sulphide deposits by highly dispersed sample values, geostatistical kriging techniques permit a more realistic estimation of the metal contained within a given volume, than the conventional methods which overestimate it. This study has been conducted by the Mineral Exploration Research institute (IREM-MERI) for SOQUEM, and is one of the few case studies released with all pertinent data. More postmortem of this kind are required for geologists and geostatisticians to improve their methods and their "batting average".

Jan 1, 1977

By M. K. Barnett

Engineering research consists, broadly speaking, in the investigation of the effect of the variations in a number of factors on some property of a product or characteristic of a process. The unambiguous description of the product or process requires that the property or characteristic be expressible in quantitative terms. For the purpose of practical control, it is likewise desirable that the independently variable factors governing the product or process be quantities, although this ideal goal is not always attained. Maximum efficiency—i.e., the attain- ment of the maximum amount of reliable, useful information relating to the influence of, the factors on the property of the product or characteristic of the process, for the least expense—is an important requirement for the satisfactory operation of a research organization. Obviously, a necessary condition for the attainment of maximum efficiency is an adequate knowledge of the specialized field in which the experimental research lies. While necessary, this condition is not sufficient. Proper attention must also be given to the general principles of experimental design together with the modern methods for the analysis and evaluation of experimental data. The Present discussion is confined to a single design, the so-called "factorial" design. This design is of special interest in that it attains its goal, maximum efficiency, by directly departing from the

Jan 1, 1948