Search Documents

A dinner was given to Ambrose Swasey by the United Engineering Society, at the Engineers' Club, on November 14. Those present -included -twenty-one presidents and past presidents of the Founder Societies. Charles F. Rand, President of United Engineering Society, presided. President Robert S. Woodward, of the Carnegie Institution of Washington, and Dr. Robert W. Hunt, of Chicago, made addresses to which Mr. Swasey responded. Dr. Michael I. Pupin, Chairman of Engineering Foundation, made the closing address. The evening was marked by the high character of the addresses, inspiration for grave duties lying before the engineering profession, and by the spirit of good fellowship. Among the seventy-two persons present were the following members of the Institute: E. E. Bartlett, William N. Best, J. Parke, Channing, C. R. Corning, F. C. Cottrell, J. V. Davies, J. V. N. Dorr, H. S. Drinker, Karl Eilers, H. M. Howe, A. C. Humphreys, Robert W. Hunt, Wm.. B. Jackson, D. S. Jacobus, J. H. Janeway, J. E. Johnson, Jr., John Johnston, George F. Kunz, Edwin Ludlow, Philip N. Moore, Fred'k. H. Newell; Wm. H. Nichols, H. Hobart Porter, Charles F. Rand, R. M. Raymond, .Jesse M. Smith, E. Gybbon Spilsbury, Bradley Stoughton, . Joseph Struthers, Benj. B. Thayer, Wm. H. Wiley, S. T. Wellman.

Jan 1, 1919

Discussion of the paper of George K. Burgess, J. J. Crowe, H. S. Rawdon, and R. G. Waltenberg, Finishing Temperatures and Properties of Rails. By Albert Sauveur, R. Trimble, William R. Webster, P. H. Dudley, George B. Waterhouse, M. H. Wickhorst, James Aston, E. F. Kenney, A. W. Gibbs, W. A. Aiken, and G. K. Burgess . . 767 Discussion of the paper of Albert Sauveur, Manganese Steel and the Allotropic Theory. By G. K. Burgess and J. E. Stead 787 Discussion of the paper of J. V. Emmons, The Surface Decarbonization of Tool Steel. By Albert Sauveur, Bradley Stoughton, E. G. Spilsbury, Oliver W. Storey, H. O. Hofman, and J. V..Emmons 790 Discussion of the paper of Richard H. Rice, Turbo Blowers for Blast-Furnace Blowing. By S. G. Valentine, W. McA. Johnson, L. Iversen, J. E. Johnson, Jr., Karl Nibecker, W. Trinks, Otto Banner, H. S. Braman, Arthur G. McKee, and Richard H. Rice . . . 794 Discussion of the paper of J. K. Furst, The Plant of the Duplex Process for Making Steel. By W. McA. Johnson, Arthur G. McKee, Henry D. Hubard, and Bradley Stoughton . . 810 Discussion of the paper of E. C. Harder, The Iron Industry in Brazil. By I. C. White and E. C. Harder 813

Jan 4, 1915

ENGINEERS AVAILABLE (Under this heading will be published notes sent to the Secretary of the Institute by members or other persons.) Member, aged 25, recent graduate, with some experience in laboratory of steel plant, desires position as metallurgist or assistant in copper, aluminum, or steel works. No. 118. Member, aged 52, technical graduate, with 20 years' experience as engineer with coal-mining companies, desires position as engineer or superintendent of coal mine. No. 119. Member, aged 39, technical graduate, with extended experience in surveying, assaying, milling, and copper smelting, desires position along cyaniding, concentration, or copper-smelting lines. No. 120. Member, aged, 38, technical graduate, with several years' experience in research work, in mine operation and as professor of mining engineering, is desirous of engagement in planning concentration and metallurgy of odd and difficult ores. No. 121. Member, aged 32, graduate M. I. T. in mining and metallurgy, at present and for last five years superintendent of Western lead smeltery, will consider engagement with solid company, if opening promises advancement. Specialty, smelting of lead ores, high in lead and zinc content. Ten years' experience in the operation, design, and erection of a large lead plant. Now desirous of bettering position.. No. 122.

Jan 8, 1914

The Institute assembled in the metallurgical lecture-room of Pardee Hall, Lafayette College, at 7 o'clock P.M. on Tuesday evening, October 21st. The session was opened by the President, R. W. Raymond, with an address on Mining Industry as illustrated at the Vienna Exposition. The second session was held on Wednesday morning. The Council reported the following names for election as members and associates. They were unanimously elected. Ayres, W. S.,.......Easton, Pa. *Baker, Prof. A. L.,.. Easton, PR. Browne, Thomas Nicholl,.... Hamilton, Nev. *Carter, Frank,......Pottsville, Pa. *Davis, E. F. C.,... Pottsville, Pa. *Fox, Prof. J. G.,...,..Easton, Pa. *Haight, Ogden,...Etna, Pa. Hall, Norman,...Sharon, Pa. *Knap, Joseph,......Fountain Mill, Pa. Miller William McKeen,.... Easton, Pa. Pardee, I. P.,....Easton, Pa. *Plater, John E.,......Eureka, Nev. *Platt, Joseph L., Jr.,.....Franklin Furnace, N. J. *Plumb, W. H.,......Mauch Chunk, Pa. *Reis, George L.,......New Castle, Pa. *Samuel, Edward,. ..Philadelphia, Pa. *Smith, William Allen,.....Trenton, N. J. *Smock, Prof. John C.,..... New Brunswick, N. J. *Weberling, Charles,.....Salt Lake City, Utah. Also the following as foreign members: Beaulieu, Ad. le Hardy de,. . Brussels, Belgium. Beaumont, Major Fred.,..London, England. Beck, Alexander,.Mons, Belgium. Bodmer, J. J.,..London, England. Brassert, Berghauptmann, Dr.,. .. Bonn, Prussia. Brogden, James,.London, England.

By S. P. Sharples

Under the act providing for the taking of the Tenth Census, the superintendent was authorized to appoint experts to inquire into special industries; accordingly Professor Charles S. Sargent was appointed to gather statistics in relation to the forest industries. As chief of the Department of Forestry of the Tenth Census he has been busily engaged in this work since the fall of 1879. Soon after his appointment he became convinced that it would be desirable to make an examination of the fuel-value of the various woods of the United States, and this work was placed in my hands. At the same time I made the suggestion that while we had the opportunity, it would be well to test also the strength of these woods. The suggestion was adopted and Professor Sargent at once set his agents to work in various parts of the country to collect specimens of all the trees growing in their localities, employing as a rule botanists who were familiar with the flora of the region in which they were at work. The result of this work was the collection of over thirteen hundred specimens of wood, comprising over four hundred species and varieties, nearly one hundred of which had not before been described as trees existing in the United States.

Jan 1, 1883

By Alfred F. Brainerd

HAVING had considerable practical experience in the management of colored mining labor in the South, I have thought a few observations upon its peculiarities might interest those not personally familiar with it. In mining, as in all other departments throughout the South, this class of labor is largely in excess of any other; and its characteristics need to be known and duly taken into consideration by those who may be charged with the conduct of southern enterprises. The colored laborers are fervently religious, intensely superstitious, improvident, and usually good natured and happy,—in a word, they are like children. That strong religious emotions do not involve necessarily a moral sense highly developed in the direction of ethics, is shown in the propensity of the colored population for chickenstealing, and in the brutal fights and other outbreaks of which they are not infrequeutly guilty, upon any slight provocation. It is only fair to say, however, that many individuals among them are in the highest degree steady and trustworthy. To one accustomed to seeing white miners at work in the middle, northern or western States, the colored miners seem somewhat slow and lazy. But their efficiency is greater than it appears to be. The almost tropical sun of midsummer beats upon their unprotected heads

Jan 1, 1886

By William Glenn

That basic slag will rapidly destroy ordinary (i.e., siliceous) fire-bricks is known to every smelter; and the smelter of copper-ores in particular knows that any kind of slag occurring in his practice is destructive. From this fact arises the chief distress of those who attempt to smelt copper-ores in any manner of furnace constructed of bricks or stone, or other similar material. We have passed the fire-brick stage of our experience; and now, having entered upon the period of the water-jacketed cupola, we will employ no furnace other than that having steel walls, kept cool by water. But,, unfortunately, the bottom of a water-jacketed cupola, kept cool by another water-jacket, fails of its purpose, being thereby made so cold as to chill both slag and regulus to a degree not bearable. The situation is more or less ameliorated when the upper surface of the water-jacketed bottom is covered with fire-bricks, since, so long as they last, they prevent the molten material from contact with the cold bottom. My own observation leads me to suppose that most smelters construct cupola-bottoms of iron slabs, which are covered, to a greater or less depth, with fire-bricks. There are cupola-bottoms which

Jan 1, 1902

By C. van Dijk

In Sept., 1960, a steam-drive project was started in the solution-gas drive area of the Schoonebeek field. A part(ern of three five-spots and one four-spot was selected covering an area of 65 acres. The pay in the project area has good lateral continuity and dips slightly to the northeut; it is about SO ft thick and permeability increases from 1,000 and at the bottom to approximately 10,000 md at the top. The oil originally in place was 12.6 X 10' bbl. The oil has an in situ viscosity of about 180 cp. At the start of the steam drive the cumulative primary production due to. solution-ga.7 drive amounted id 4 Percent of the oil originally in place. Reservoir pressure had dropped about 120 psi and no significant primary re-.serves remained. Some 11.3 million bbl of steam (all steam quantities are expressed in barrels of water vaporized) have been injected, resulting in production of an additional 4.1 X I0 9bl of oil, or 33 percent of the oil originally in place. This corresponds to a cumulative oil-stearn rario of 0.37 bbllbbl. It appears that the steam preferentially moves r updip while liquids are produced mainly from downdip wells observations indicate that tile steam flows through only the upper part of the formation. The lateral steam distribution in the pattern is satisfacrory since several prodriction wells hardly reacted and, hence, cori tributcd little to the oil production. Production performance and results from material balance calcutlations agree satisfactorily with the results of large-,scale laboratory experiments. On the basis of these experirmental results the .steam drive, together with a cold water follow-up. is expected to bring ultimate recovery to a value of crt leas: 50 percent of the oil originally in place. No serious production problems have been encountered. However, due to mechanical fuilure, two old prodriction wells and one injection well had to be replaced. An extension of the. steam drive in this area is under connstruction. Introduction The Schoonebeek oil field, discovered in 1943 and developed after World War 11, is situated in the eastern part of the Netherlands. The main oil reservoir in this field is the Valanginian sand. A completely sealing fault divides this reservoir into two areas (Fig. 1): the southwestern part of the sand body where primary production is ob- tained by means of a solution-gas drive, and the remain. der where edge-water drive is the production mechanism. In the greater part of the field the reservoir consists of a single, unconsolidated sand body. The net thickness ranges from 30 to 100 ft and the top is between 2,400 and 2,800 ft below sea level. Formation permeability varies from approximately 10,000 md at the top to values of the order of 1,000 md at the bottom, and porosity is about 30 percent. The reservoir contains a paraffinic oil of 25" API gravity with an in situ viscosity of 160 to 180 cp. Initial oil saturation was high (85 to 90 percent). The relatively large quantity of oil in place (more than 10' bbl), and the low ultimate primary recoveries expected from this field — approximately 15 percent stock-tank oil initially in place (STOIIP) for the water-drive area and 5 percent STOIIP for the solution-gas drive area — clearly indicate ample scope for secondary recovery. Because ies-ervoir and crude characteristics made this field suitable for thermal secondary recovery, a hot-water drive project was started in the water-drive area about 10 years ago. A few years later a steam drive and an in situ combustion project were started in the solution-gas drive area. This paper deals with the performance of the steam-drive project, which was started in Sept., 1960, and which is still in operation. Design of Steam-Drive Project, An experimental investigation of the steam-drive process carried out by schenk in 19561 indicated that under schoonebeek conditions steam injection could be an attractive secondary recovery method. the findings and encouraging results of a pilot test in the Mene Grande field in venezuela,i led to the design of a steam-drive project in the schoonebeek field, Pruject Site and Pattern In 1958 the reservoir pressure in the solution-gas drive area had decreased to about 120 psi, and oil production rates of wells in this area had dropped to 7 to 10 B/D. The cumulative primary production was about 4 percent STOIIP, leaving an oil saturation of approximately 85 percent. In view of the large amount of oil left behind in the reservoir, the solution-gas drive area was selected for the planned steam-drive project. The area in the vicinity of Well S1 3 (Fig. 2) was considered to be suitable since it is at least partly isolated from the rest of the field by faults and the sand is relatively thick (about 80 ft).

Jan 1, 1969

By E. Miller, R. Geffken, K. L. Komarek

The thermodynamzc properties oJ liquid Cd-Sb alloys were investigated using the cell arrangement measurments were obtained every 2°C at a heating and cooling rate of 12°C per hr and at equilibrium every 2O0C frorn 500°C down through the stable liquidus. The S-shaped asCd US composition curve was used in the cotnposition regzon near Cd,Sb, to calculate a tempeerture-dependent inleraction coefficient from quasichemical theory. Rapid changes in a scd were observed at a transition temperature varying from 400" to 465°C depending on con/kosition. It could not be determined if the changes in aScd were discontinuous, but tlze composition dependeke of the magnitude of the change is indicative of a second-order phase transformation in the liquid. The values of the experimental changes in ASCd are in agreement with calculations from the slope of the transition temperature, using the concept that a second-ovdev phase transition occurs in liquid Cd-Sb alloys. II is suggested that the transformalion is associated with the formation of Cd4Sb3 molecules in the liquid. ThE structure of liquid alloys is the subject of many investigations. X-ray, resistivity, and thermody-namic data have been interpreted as indicating varying degrees of short-range order in the liquid in alloy systems forming inter metallic compounds. In general, the melting process is not a transition from an ordered to a completely disordered state, but some degree of order is retained in the liquid. Maximum ordering in the liquid state occurs close to the melting temperature of the compound and the arrangement of atoms becomes more random at higher temperatures. Of special interest in this respect is the Cd-Sb system. It is one of the few metallic systems which form both stable and metastable compounds when liquid alloys are cooled at normal rates. The stable system exhibits an intermetallic compound, CdSb, melting at 459"c.l A second compound, CdrSbs, has also been reported,' melting close to this temperature. The metastable system has one compound, CdsSbz, melting at 420"c.I Resistivity measurements on liquid Cd-Sb alloys close to the liquidus temperatures have been interpreted in terms of a complex ordering behavior which changes rapidly with increasing temperature.3 The resistivity-composition curve is characterized by two maxima corresponding in composition to CdSb and CdsSbz. The resistivity-temperature plots show sharp breaks for alloys in the composition range of 45 to 70 at. pct Cd on cooling through a transition temperature close to the stable liquidus. Fisher and phillips4 investigated the influence of temperature and composition on the viscosity of liquid CdSb alloys. The viscosity of some alloys increases sharply on supercooling below the stable liquidus. A maximum in the viscosity-composition curve occurs at the composition CdSb. The thermodynamic properties of liquid Cd-Sb alloys have been investigated by Seltz and ~e~itt' and Elliott and chipmane by the electromotive-force method and their results are in good agreement. However, these investigations were carried out at temperatures well above the liquidus temperatures of the alloys, and the temperature coefficients of the electromotive force, dE/dT, were obtained from experimental points for each alloy at a few temperatures considerably above the liquidus temperature. Scheil and ~aach' investigated the thermodynamic properties of this system by the dew point method in the temperature range from about 100°C above the stable liquidus down into the supercooled liquid region. They reported several anomalies, i.e., the activity of a melt on heating differed from that on cooling, and the activity increased sharply in the limited temperature interval immediately above the liquidus temperature of the stable alloy, followed by a sudden decrease below the liquidus. Values obtained on heating and cooling were not in agreement. A reinvesti-gation of a few alloys by Scheil and Kalkuhl' by the electromotive-force method failed to confirm these observations. The authors concluded that the anomalies were due to inhomogeneities in the starting alloys and they discarded their previous results. The present investigation was undertaken in order to obtain thermodynamic data close to the liquidus temperature and in the supercooled region where the anomalies were originally reported, employing the electro motive-force method. This method is quite precise and will most easily permit observations of small changes in activity and partial molar entropy with temperature. Measurements were taken every few degrees so that the dE/dT values could be calculated over the entire temperature range and small changes in the thermodynamic properties close to the liquidus temperature could be observed. I) EXPERIMENTAL PROCEDURE Specimens were prepared from 99.999+ pct Cd and Sb (Cominco). Surface oxide was removed by scraping and then melting the metals under vacuum and filtering through Pyrex wool. Appropriate amounts of the metals were weighed on an analytical balance to k0.1 mg, sealed in double Pyrex capsules under vacuum,

Jan 1, 1968

By J. A. Barr, R. B. Burt, I. S. Tillotson

THE pumping of solids in water suspension is an important part of many metallurgical and mining operations. In most cases, it is still in the rule of thumb category for which no universal formula has been developed, and much research is needed. Because of the limited and incomplete data available, this article may be classed as an experience paper, which is presented with the hope that some contribution will be made toward the development of the so-called universal formula. This formula, if and when developed, may be evolved from several factors, many of which are not now available for general application. The designing engineer is interested in obtaining accurate forecasts on: 1—the minimum velocities needed to prevent choke-ups in the pipeline, which in turn dictates pipe sizes, 2—power required for pumping, 3—pump selection. The basic factors for a given problem will include: 1—weight per unit of time of solids to be handled, 2—specific gravity of solids, for calculation of volume, friction and power, 3—screen analysis of solids with the colloidal acting, i.e., the slime fraction, a very important factor, 4— shape of particle or some means of determining a friction constant, 5—effects of percentage of solids, 6—development of a viscosity factor to be used in the overall calculations, 7—calculation of the lower limits of pipeline velocities permissible, 8—calculation of total head, pump horsepower, and 9—setting up of pump specifications. In certain limited cases horsepower and total heads and minimum velocities may be computed and a suitable pump selected from basic data, but in many cases, as in mining of Florida pebble phosphate, experience rather than a hydraulic formula still should be used as a basis of selection. Pumping Florida Pebble Matrix Pumping at the Noralyn mine of International Minerals and Chemical Corp. will be used as an example. Other areas will vary as to the characteristics of the matrix, especially the slime content. A typical screen analysis of this matrix is: +14 mesh, pebble size,* 2.1 pct; —14 +35 mesh, 11.4 pct; -35 +I50 mesh, 60.5 pct; -150 mesh, 25.0; total, 100 pct; moisture in bank, 20.0 pct; weight per cu ft in bank, 120 lb. The —150 mesh fraction may increase to as much as 35 pct in adjacent areas. When thoroughly elutriated, the matrix has a relatively slow settling rate, which is an important factor in permitting lower pipeline velocities without choke-ups. Exact data is not available to evaluate settling rates. For a factor of 100 a suspension of clean building sand in water is suggested. When pumping long * Pebble is a commercial designation for the coarser fraction of finished phosphate from a washer, usually +14 mesh. distances, a quick settling matrix allows the coarser solids to settle out along the bottom of the pipeline, causing drag, turbulence, and increased friction. With a slow settling matrix as at Noralyn, turbulence acts to keep the solids in suspension at a lower friction head, regardless of the pumping distance. When the pebble content of the matrix, i.e., the + 14 mesh fraction, is in excess of 10 pct of the total solids, trouble may be expected from settling out even in normal pumping distances. To prevent choke-ups and maintain tonnage, an additional pump must be added in the long runs, where one pump would otherwise be satisfactory. A typical pulp handled is: total volume, 7800 gpm; water, 4500; solids pumped per hr, 4200 lb; sp gr pulp, 1.4; percent solids in pulp, 46.; pipe size, 16-in. ID; pulp velocity, 12.85 fps; probable critical velocity, 10 fps, as below this minimum velocity choke-ups would be numerous. In calculating friction heads the Armco handbook is used where a roughness factor based on 15-year-old pipe is set up. Because the pipe used in pumping matrix is smooth and polished because of the scouring action of the phosphate and its silica content, the head losses in the Armco table for water are practically the same as in pumping the Noralyn matrix through smooth pipe, plus the fact that conditions vary widely over short periods, making accurate determinations difficult to obtain. New pumps and pump changes are being tested continuously and a wealth of data built up. This has resulted in a substantial improvement and lower relative costs in pumping matrix. The Florida phosphate industry is constantly seeking to offset higher wage and material costs with improved technique. Until a few years ago a 12-in. discharge pump was commonly used, with heads as low as 80 ft. Sizes have gradually increased and heads more than doubled. For example, the following pump was placed under test at the Noralyn mine: make, Georgia Iron Works; size, suction 16 in., discharge 14 in.; impeller, 39-in. diam; motor, 600 hp, slip ring; full load speed, 514 rpm. The results were increased head, higher capacity than the older design, with fewer pumps in the line from mine to washer.

Jan 1, 1953

By R. B. Burt, J. A. Barr, I. S. Tillotson

THE pumping of solids in water suspension is an important part of many metallurgical and mining operations. In most cases, it is still in the rule of thumb category for which no universal formula has been developed, and much research is needed. Because of the limited and incomplete data available, this article may be classed as an experience paper, which is presented with the hope that some contribution will be made toward the development of the so-called universal formula. This formula, if and when developed, may be evolved from several factors, many of which are not now available for general application. The designing engineer is interested in obtaining accurate forecasts on: 1—the minimum velocities needed to prevent choke-ups in the pipeline, which in turn dictates pipe sizes, 2—power required for pumping, 3—pump selection. The basic factors for a given problem will include: 1—weight per unit of time of solids to be handled, 2—specific gravity of solids, for calculation of volume, friction and power, 3—screen analysis of solids with the colloidal acting, i.e., the slime fraction, a very important factor, 4— shape of particle or some means of determining a friction constant, 5—effects of percentage of solids, 6—development of a viscosity factor to be used in the overall calculations, 7—calculation of the lower limits of pipeline velocities permissible, 8—calculation of total head, pump horsepower, and 9—setting up of pump specifications. In certain limited cases horsepower and total heads and minimum velocities may be computed and a suitable pump selected from basic data, but in many cases, as in mining of Florida pebble phosphate, experience rather than a hydraulic formula still should be used as a basis of selection. Pumping Florida Pebble Matrix Pumping at the Noralyn mine of International Minerals and Chemical Corp. will be used as an example. Other areas will vary as to the characteristics of the matrix, especially the slime content. A typical screen analysis of this matrix is: +14 mesh, pebble size,* 2.1 pct; —14 +35 mesh, 11.4 pct; -35 +I50 mesh, 60.5 pct; -150 mesh, 25.0; total, 100 pct; moisture in bank, 20.0 pct; weight per cu ft in bank, 120 lb. The —150 mesh fraction may increase to as much as 35 pct in adjacent areas. When thoroughly elutriated, the matrix has a relatively slow settling rate, which is an important factor in permitting lower pipeline velocities without choke-ups. Exact data is not available to evaluate settling rates. For a factor of 100 a suspension of clean building sand in water is suggested. When pumping long * Pebble is a commercial designation for the coarser fraction of finished phosphate from a washer, usually +14 mesh. distances, a quick settling matrix allows the coarser solids to settle out along the bottom of the pipeline, causing drag, turbulence, and increased friction. With a slow settling matrix as at Noralyn, turbulence acts to keep the solids in suspension at a lower friction head, regardless of the pumping distance. When the pebble content of the matrix, i.e., the + 14 mesh fraction, is in excess of 10 pct of the total solids, trouble may be expected from settling out even in normal pumping distances. To prevent choke-ups and maintain tonnage, an additional pump must be added in the long runs, where one pump would otherwise be satisfactory. A typical pulp handled is: total volume, 7800 gpm; water, 4500; solids pumped per hr, 4200 lb; sp gr pulp, 1.4; percent solids in pulp, 46.; pipe size, 16-in. ID; pulp velocity, 12.85 fps; probable critical velocity, 10 fps, as below this minimum velocity choke-ups would be numerous. In calculating friction heads the Armco handbook is used where a roughness factor based on 15-year-old pipe is set up. Because the pipe used in pumping matrix is smooth and polished because of the scouring action of the phosphate and its silica content, the head losses in the Armco table for water are practically the same as in pumping the Noralyn matrix through smooth pipe, plus the fact that conditions vary widely over short periods, making accurate determinations difficult to obtain. New pumps and pump changes are being tested continuously and a wealth of data built up. This has resulted in a substantial improvement and lower relative costs in pumping matrix. The Florida phosphate industry is constantly seeking to offset higher wage and material costs with improved technique. Until a few years ago a 12-in. discharge pump was commonly used, with heads as low as 80 ft. Sizes have gradually increased and heads more than doubled. For example, the following pump was placed under test at the Noralyn mine: make, Georgia Iron Works; size, suction 16 in., discharge 14 in.; impeller, 39-in. diam; motor, 600 hp, slip ring; full load speed, 514 rpm. The results were increased head, higher capacity than the older design, with fewer pumps in the line from mine to washer.

Jan 1, 1953

By J. A. Barr, R. B. Burt, I. S. Tillotson

THE pumping of solids in water suspension is an important part of many metallurgical and mining operations. In most cases, it is still in the rule of thumb category for which no universal formula has been developed, and much research is needed. Because of the limited and incomplete data available, this article may be classed as an experience paper, which is presented with the hope that some contribution will be made toward the development of the so-called universal formula. This formula, if and when developed, may be evolved from several factors, many of which are not now available for general application. The designing engineer is interested in obtaining accurate forecasts on: 1—the minimum velocities needed to prevent choke-ups in the pipeline, which in turn dictates pipe sizes, 2—power required for pumping, 3—pump selection. The basic factors for a given problem will include: 1—weight per unit of time of solids to be handled, 2—specific gravity of solids, for calculation of volume, friction and power, 3—screen analysis of solids with the colloidal acting, i.e., the slime fraction, a very important factor, 4— shape of particle or some means of determining a friction constant, 5—effects of percentage of solids, 6—development of a viscosity factor to be used in the overall calculations, 7—calculation of the lower limits of pipeline velocities permissible, 8—calculation of total head, pump horsepower, and 9—setting up of pump specifications. In certain limited cases horsepower and total heads and minimum velocities may be computed and a suitable pump selected from basic data, but in many cases, as in mining of Florida pebble phosphate, experience rather than a hydraulic formula still should be used as a basis of selection. Pumping Florida Pebble Matrix Pumping at the Noralyn mine of International Minerals and Chemical Corp. will be used as an example. Other areas will vary as to the characteristics of the matrix, especially the slime content. A typical screen analysis of this matrix is: +14 mesh, pebble size,* 2.1 pct; —14 +35 mesh, 11.4 pct; -35 +I50 mesh, 60.5 pct; -150 mesh, 25.0; total, 100 pct; moisture in bank, 20.0 pct; weight per cu ft in bank, 120 lb. The —150 mesh fraction may increase to as much as 35 pct in adjacent areas. When thoroughly elutriated, the matrix has a relatively slow settling rate, which is an important factor in permitting lower pipeline velocities without choke-ups. Exact data is not available to evaluate settling rates. For a factor of 100 a suspension of clean building sand in water is suggested. When pumping long distances, a quick settling matrix allows the coarser solids to settle out along the bottom of the pipeline, causing drag, turbulence, and increased friction. With a slow settling matrix as at Noralyn, turbulence acts to keep the solids in suspension at a lower friction head, regardless of the pumping distance. When the pebble content of the matrix, i.e., the + 14 mesh fraction, is in excess of 10 pct of the total solids, trouble may be expected from settling out even in normal pumping distances. To prevent choke-ups and maintain tonnage, an additional pump must be added in the long runs, where one pump would otherwise be satisfactory. A typical pulp handled is: total volume, 7800 gpm; water, 4500; solids pumped per hr, 4200 lb; sp gr pulp, 1.4; percent solids in pulp, 46.; pipe size, 16-in. ID; pulp velocity, 12.85 fps; probable critical velocity, 10 fps, as below this minimum velocity choke-ups would be numerous. In calculating friction heads the Armco handbook is used where a roughness factor based on 15-year-old pipe is set up. Because the pipe used in pumping matrix is smooth and polished because of the scouring action of the phosphate and its silica content, the head losses in the Armco table for water are practically the same as in pumping the Noralyn matrix through smooth pipe, plus the fact that conditions vary widely over short periods, making accurate determinations difficult to obtain. New pumps and pump changes are being tested continuously and a wealth of data built up. This has resulted in a substantial improvement and lower relative costs in pumping matrix. The Florida phosphate industry is constantly seeking to offset higher wage and material costs with improved technique. Until a few years ago a 12-in. discharge pump was commonly used, with heads as low as 80 ft. Sizes have gradually increased and heads more than doubled. For example, the following pump was placed under test at the Noralyn mine: make, Georgia Iron Works; size, suction 16 in., discharge 14 in.; impeller, 39-in. diam; motor, 600 hp, slip ring; full load speed, 514 rpm. The results were increased head, higher capacity than the older design, with fewer pumps in the line from mine to washer.

Jan 1, 1953

By R. B. Burt, J. A. Barr, I. S. Tillotson

THE pumping of solids in water suspension is an important part of many metallurgical and mining operations. In most cases, it is still in the rule of thumb category for which no universal formula has been developed, and much research is needed. Because of the limited and incomplete data available, this article may be classed as an experience paper, which is presented with the hope that some contribution will be made toward the development of the so-called universal formula. This formula, if and when developed, may be evolved from several factors, many of which are not now available for general application. The designing engineer is interested in obtaining accurate forecasts on: 1—the minimum velocities needed to prevent choke-ups in the pipeline, which in turn dictates pipe sizes, 2—power required for pumping, 3—pump selection. The basic factors for a given problem will include: 1—weight per unit of time of solids to be handled, 2—specific gravity of solids, for calculation of volume, friction and power, 3—screen analysis of solids with the colloidal acting, i.e., the slime fraction, a very important factor, 4— shape of particle or some means of determining a friction constant, 5—effects of percentage of solids, 6—development of a viscosity factor to be used in the overall calculations, 7—calculation of the lower limits of pipeline velocities permissible, 8—calculation of total head, pump horsepower, and 9—setting up of pump specifications. In certain limited cases horsepower and total heads and minimum velocities may be computed and a suitable pump selected from basic data, but in many cases, as in mining of Florida pebble phosphate, experience rather than a hydraulic formula still should be used as a basis of selection. Pumping Florida Pebble Matrix Pumping at the Noralyn mine of International Minerals and Chemical Corp. will be used as an example. Other areas will vary as to the characteristics of the matrix, especially the slime content. A typical screen analysis of this matrix is: +14 mesh, pebble size,* 2.1 pct; —14 +35 mesh, 11.4 pct; -35 +I50 mesh, 60.5 pct; -150 mesh, 25.0; total, 100 pct; moisture in bank, 20.0 pct; weight per cu ft in bank, 120 lb. The —150 mesh fraction may increase to as much as 35 pct in adjacent areas. When thoroughly elutriated, the matrix has a relatively slow settling rate, which is an important factor in permitting lower pipeline velocities without choke-ups. Exact data is not available to evaluate settling rates. For a factor of 100 a suspension of clean building sand in water is suggested. When pumping long distances, a quick settling matrix allows the coarser solids to settle out along the bottom of the pipeline, causing drag, turbulence, and increased friction. With a slow settling matrix as at Noralyn, turbulence acts to keep the solids in suspension at a lower friction head, regardless of the pumping distance. When the pebble content of the matrix, i.e., the + 14 mesh fraction, is in excess of 10 pct of the total solids, trouble may be expected from settling out even in normal pumping distances. To prevent choke-ups and maintain tonnage, an additional pump must be added in the long runs, where one pump would otherwise be satisfactory. A typical pulp handled is: total volume, 7800 gpm; water, 4500; solids pumped per hr, 4200 lb; sp gr pulp, 1.4; percent solids in pulp, 46.; pipe size, 16-in. ID; pulp velocity, 12.85 fps; probable critical velocity, 10 fps, as below this minimum velocity choke-ups would be numerous. In calculating friction heads the Armco handbook is used where a roughness factor based on 15-year-old pipe is set up. Because the pipe used in pumping matrix is smooth and polished because of the scouring action of the phosphate and its silica content, the head losses in the Armco table for water are practically the same as in pumping the Noralyn matrix through smooth pipe, plus the fact that conditions vary widely over short periods, making accurate determinations difficult to obtain. New pumps and pump changes are being tested continuously and a wealth of data built up. This has resulted in a substantial improvement and lower relative costs in pumping matrix. The Florida phosphate industry is constantly seeking to offset higher wage and material costs with improved technique. Until a few years ago a 12-in. discharge pump was commonly used, with heads as low as 80 ft. Sizes have gradually increased and heads more than doubled. For example, the following pump was placed under test at the Noralyn mine: make, Georgia Iron Works; size, suction 16 in., discharge 14 in.; impeller, 39-in. diam; motor, 600 hp, slip ring; full load speed, 514 rpm. The results were increased head, higher capacity than the older design, with fewer pumps in the line from mine to washer.

Jan 1, 1953

By D. Cox, M. J. Duggin, L. Zwell

The carbides of approximate composition and Mn have been studied using X-ray diffraction techniques. Those carbides of the type (Fe,Aln)zC ave isostructural with cementite. The cell pararmeters a and c have minimum values at approximately 10 at. pd substitution of manganese for iron; no satisfactory explanation has yet been found for this phenomenon. The carbide fFeMn4)C has a monoclinic unit cell whose dimensions are close to those of ,11,15Cz A neu-troip-dij~ractiot~ study of (F'eAlrz4)C~ reveals that, like MnsCZ, it is isostructural with Pd5Bz. The iron and manganese atoms occupy the palladium atom sites, while the carbon atoms were found to have the same atomic coordinates as the hovon atoms. A neutrorr-diffraction study of indicates that the carbon-atom positions are very close to those occupied in (Fez.,ll/lr~,.3)C. In both carbides studied, tlre iron and manganese atomzs were found to be essentially randomly distributed, although, in the case of (Fe,.811fn1.2)C, it is possible that there may be a slight preference of manganese atoms for- the general (d) positions and a corresponding slight preference of iron atoms for the special (c) positions. It has been found that a complete range of solid solution exists between Fe3C and Mn3C at 1050°C,I although Mn3C becomes unstable when the temperature is reduced to 95O0C,' and can only be retained by rapid quenching. It is also known that a complete range of solid solution exists from Fe5Cz to M~SC~,~ although the stability range of carbides of the type (Fe,Mn)sCz as a function of the relative proportions of iron and manganese is not known. X-ray examinations of Oh-man's carbide3 and Spiegeleisenkristall,~ which have the approximate compositions (Fe3.67Mnl.33)C2 and (Fe3-,Mn,)C, where x lies between 0.4 and 1, respectively, have been made. The following carbides have also been studied: ] The lattice parameters determined during these investigations are listed in Table I. It is seen that carbides of the type (Fe,Mn)sCz have a monoclinic unit cell while carbides of the type (Fe,Mn)3C have an orthorhombic unit cell. It is evident that the variation of lattice parameters with manganese content is not linear for carbides of the type (Fe,Mn)3C. The coordinates of the atoms in (Fe2.7Mno.3)C have recently been determined by single-crystal analysis., The fractional atomic coordinates have been shown by Fasiska and jeffrey to be in good agreement withj those deduced from an earlier analysis of Fe3C by Lipson and etch.' However, it was impossible to determine whether iron and manganese atoms occupied ordered positions because of the small difference between the atomic scattering factors of iron and manganese. The atomic positions in Mn5Cz (Refs. 8 and 9) and Fe5C2 (Refs. 7 and 8) have been obtained only by comparisons made with the isostructural compounds P~SB~.' Since X-ray diffraction techniques were used in these investigations, accurate positioning of the carbon atoms, which have a low atomic scattering factor, was difficult. No attempt has been made to determine the atomic positions in the other carbides previously studied. It was felt that an investigation of the lattice parameters of a number of intermediate carbides of the types (Fe,Mn)sCZ and (Fe,Mn)& would be of interest. It seemed likely that a neutron-diffract ion study of such carbides would indicate whether ordering occurred between the iron and manganese atoms because of the large difference between the neutron-scattering cross sections of iron and manganese. It also seemed probable that such an investigation would provide a determination of the atomic coordinates of the carbon atoms. I) EXPERIMENTAL DETAILS Specimens, each weighing approximately 20 g, were carefully prepared according to the following proportions: The components were 500-mesh powders of 99.995 pct purity iron and spectroscopically pure carbon and a 200-mesh powder of 99.995 pct purity manganese. The component powders were intimately mixed by prolonged shaking, then each specimen was inserted into a spot-welded cylindrical container of tantalum foil, whose end was closed but not sealed. Each specimen in its envelope was then sintered at 1050° C for 24 hr in a thin-walled evacuated quartz capsule, such a time having been previously found sufficient for equilibrium to be attained.' Each specimen was then quenched in order to attempt to retain the high-temperature phase, as the literature indicates that transformations may occur on cooling. Debye-Scherrer X-ray photographs were taken of each specimen using a 114.6-mm-diam camera, Fig. 1, patterns 2 to 6. The exposure time was 6 hr using filtered iron radiation at a tube voltage of 40 kv and a tube current of 12 ma.

Jan 1, 1967

By John Chipman

The concentration of a solute in a dilute ),zetallic solution may be measured by any of several parame- ters including weight percent, atom fraction, atom ratio, and lattice ratio. The ratio of filled to unfilled interstitial sites is useful for interstitial solutes. A variable 2 proportional to this ratio is used as a measuve of concentration. For component 2 irz a bitzary solution z2 = n2/Ym - nz/b) where b is the numberber of interstitial sites per lattice atom. For a t~lul-ticortzporzent solution this becomes zz = n2/(nl + Cvjnj) in which Vj = - l/b for an interstial solute and +1 for a substitulional solute. In the infinitely dilute solution the activity of an interstitial solute 2 is proportional lo z2. At finile concentration the departure from this limiting law is expressed us an activity coefficient, his coefficient is a function of concentra1io)z expressed as tevactiolz coeffcient 8; is analogous to the jark~iliar e£ bul is found to be independent of concentvation in certain solutions for which data are available. It is found that the same equations may be used to express the activity of a nonmetallic solute, sulfur, in liquid solutions of iron containing other solutes, both metallic and nonmetallic. For a nonmetallic solute or for one which strongly increases the actiuity of sulfur, it is convenient to assign arbitvarily a value vj = — 1. When this is done the derivative is found to be constant in each of the ternary solutions studied. The activity coefficient of sulfur in a complex liquid iron solution may be expressed as where nk is a second-order cross product determined in the quaternary solution Fe-S-j-k. The equation is used to calculate tlze activity of sulfur i)z three sevetl- component solutions. IN thermodynamic calculations concerning dilute solutions it is unnecessary to invoke laws and relations which extend across the concentration range to include concentrated solutions. In most binary metallic systems, as arkeen&apos; has recently pointed out, there exist two terminal composition regions of relatively simple behavior, connected by a central region of much greater complexity. When the solute is a nonmetal there is only one such region and in many systems the concentration range is extremely limited. It is the purpose of this paper to suggest a method for the calculation of activities in such a terminal region in which one or more solutes are dissolved in a single solvent of predominantly high concentration. HENRY&apos;S LAW In the usual textbook statement of Henry&apos;s law, concentration is stated in mole fraction. This has the advantage that it makes Henry&apos;s law thermodynamically consistent with Raoult&apos;s law. Since all measures of concentration at infinite dilution are related by simple proportion it follows that mole fraction, molality, atom ratio, weight percent, or any other unit of concentration can be used with the appropriate constant. At finite concentrations, however, calculations based on the law depend upon the unit employed. Deviations from Henry&apos;s law at finite concentrations depend upon the composition variable employed. They are evaluated in terms of activity and interaction coefficients2 which have become familiar features of metallurgical thermodynamics. It is the purpose of this paper to propose a measure of concentration for metallic solutions containing interstitial or nonmetallic solutes by means of which the calculation of activities in complex solutions may be simplified. The discussion will be restricted to free-energy interaction coefficients3 typified by Wagner&apos;s c|a BINARY SOLUTIONS The several measures of concentration which are to be considered are shown in line a of Table I. The corresponding activity coefficients are in line b and the deviation coefficients, sometimes called self-interaction coefficients, are in line c. Henry&apos;s law simply states that the activity coefficient approaches a constant value at infinite dilution. By adoptihg the infinitely dilute solution as the reference state and defining the "Henrian" activity as equal to the concentration in this state, the activity coefficient is always unity at infinite dilution. This convention is far sim~ler and more useful in dilute solution than emploiment of the &apos;Raoultian" activities and it will be used in the following discussion. The several definitions and equations of Table I will be referred to by means of their coordinates in the table. Early observations of deviations from Henry&apos;s law in metallic solutions were shown graphically4 rather than analytically. For the case of sulfur in liquid iron5 the slope of a plot of logfs vs (%S) was constant in the range 0 to 4.8 pct S, indicating constancy of eh2&apos; in Ic. He was proposed by wagnerz and has been widely adopted. The a function of IIIc recently employed by ~arkenl was designed specifically for dilute solutions. Darken has shown that the value of a12 remains essentially constant for many binary solutions within a substantial range of compositions. The atom ratio is directly proportional to the molalitv.<, a conventional measure of concentration. IVb and C served as the basis for smith&apos;s6 classic studies of

Jan 1, 1968

By F. W. Glaser

Metal-carbon-boron powder mixtures were hot pressed and the resulting specimens were studied by X-ray diffraction. It was found that regardless of the starting combination of the metal, carbon, or boron powders, a metal boride phase was always the major component in these samples. In the absence of carbon the boride phase formed on hot pressing depended only on the amount of boron present. Two new phases of the system Ti-B were found. They are Ti2B and Ti2B5. The existence of a controversial face-centered cubic phase of formula TiB was confirmed. Electrical resistivities were measured for various boride phases. It was found that the diborides are generally better conductors than the monoborides of the same metal. THE carbides and borides of the transition elements have very high melting points, in the range 2500° to 4000°C, and are therefore of interest as high temperature materials. The literature on the stability or chemical reactivity of these carbides and borides is very scarce. Various investigators&apos;-" have demonstrated a relative instability of certain carbide phases in the presence of boron or boron-containing substances. In a recent publication, Glaserl demonstrated the stability of zirconium-boride (ZrB,) in the presence of carbon at temperatures in excess of approximately 2900°C, while during a preliminary investigation of boride phases, Steinitz&apos; concluded that the diborides are stable in the presence of carbon while the monoborides of the fourth and fifth group are not, forming diborides plus carbides instead. Nelson, Willmore, and Womeldorph" have elaborated on the reaction B,C + 2TiC = 2TiB, + 3C, which was known to occur because of a relative instability of B,C and the great tendency towards TiB, formation at relatively low temperatures (approximately 1200°C). A similar study, involving as starting materials TiO, and B,C and resulting in TiB,, was recently described by Honak4, who observed the beginning of an exothermic reaction of a Ti0,-B,C powder mixture, which, when preheated in a hydrogen atmosphere to approximately 950°C, was carried to about 1600 °C by the heat of reaction. To shed more light on reactions of this type (Metal-C-B), the final product apparently always resulting in a boride phase at the expense of a carbide phase," a systematic investigation was started * Boride phases of various metals, as reported to date, are listed in Table I. and the following is an account of some of the results that were obtained. Materials, Preparation of Samples, Testing Methods The raw materials employed for this work consisted of various carbide, boride, and metal powders. as well as of boron and graphite powders. In cases where commercial grades of carbides were considered unsuitable because of low purity or excessive amounts of graphitic carbon, such carbide powders were prepared by this laboratory. The procedure for the preparation of carbide powders (zirconium carbide, titanium carbide, tantalum carbide, and niobium carbide) consisted of mixing graphite and the respective metal hydride powders in stoichio-metric proportions and subsequent heating of such mixtures in a hydrogen atmosphere in carbon crucibles. The heating was by high frequency to temperatures ranging between 1700" and 2100°C. The resulting carbide was then comminuted and screened to the desired particle size. ZrB, and TiB, powders were produced by the electrolysis of fused salt baths, according to the method described by Andriex.. The borides of niobium, vanadium, tantalum, molybdenum, chro-ium, and iron were obtained by mixing the respective metal and boron powders in the desired proportions. Such metal-boron mixtures were heated in a high frequency furnace to form boride powders. For each metal-carbon-boron group (Tables I1 through XI) a metal, its hydride, carbide or boride were mixed with carbon, boron or boron carbide powders. The additions of carbon, boron or boron carbide powders to any of these metals or metal compounds were calculated to satisfy a particular carbide or boride phase that according to the literature (Table I) had definitely been established by X-ray diffraction work. Samples of powder mixtures were hot pressed in graphite molds that were heated by direct conduction. The specimen dimensions were approximately 2.5X1X1 cm. Hot pressing temperatures were measured optically and maintained for approximately 30 sec under a constant pressure of about 1.3 ton per sq in. Wherever possible, an attempt to obtain maximum specimen density was made by temperature variation. Electrical resistivity testing was done by measuring potentiometrically the voltage drop over a length of 1.5 cm for a current of 10 amp, at room temperature. To obtain electrical resistivities for specific carbide or boride phases, values were plotted as a function of the respective sample densities

Jan 1, 1953

By A. E. Jenkins, O. C. Roberts, D. G. C. Robertson

Using an inverted-cone coil at 450 kHz, it has been possible to levitate iron (FeS), cobalt (CoS), and nickel (NiS) sulfides. Important nontransition metal sulfides such as ZnS, PbS, and Cu2S have proven impossible to levitate although Cu-Fe-S ternary alloys containing 30 wt pct S and up to 10 wt pct Cu, and Cu-Co-S and Cu-Ni-S ternary alloys containing 30 wt pct Cu have been levitated. The levitation technique has been used in preliminary experiments on the vaporization from liquid sulfides and the reaction of liquid metal-sulfur alloys with oxidizing atmospheres. The course of the reactions with pure oxygen were followed using highspeed photography and two-color pyrometry. ELECTROMAGNETIC levitation is now established as a basic laboratory technique in high-temperature research but its application has been restricted mainly to metals and alloys. Applications have included alloy preparation,&apos; metal purification,2&apos;3 determination of liquid metal densities and emissivities,4,5 and studies of metal supercooling,4 alloy thermodynamics,6 and vaporization phenomena.7-9 The application of the technique to compounds has not been considered previously. The successful investigation of the reactions between dilute iron alloys and oxidizing atmospheres10&apos;1 has prompted the current physico-chemical studies involving levitated metal sulfide drops and flowing inert or oxidizing atmospheres. This paper presents the results of such a study and provides a basis for future studies involving a wide range of other compounds of metallurgical interest. The successful levitation of many metal sulfides and mattes provides a method of studying the oxidation reactions fundamental to flash-smelting and similar pyrometallurgi-cal operations under closely controlled laboratory conditions. In addition the system allows the use of a controlled atmosphere (e.g., a gas stream of a certain H2/H2S ratio) with a particular chemical potential to study the relevant thermodynamic equilibria or the mass transfer processes between the atmosphere and the levitated drop under conditions where the hydrodynamics of the system can be closely defined. The optimum frequency for the levitation melting of metals in an inverted-cone coil type inductor is within the radio frequency range 400 to 500 kHz. At frequencies lower than 10 kHz the rate of heat generation is usually insufficient to melt the levitated charge&apos; or where melting is achieved, "dripping" from the charge is encountered.&apos;&apos; At frequencies above 2 mHz the levitation force decreases. Metals, alloys and preheated elemental semiconductors such as germanium and silicon, have been levitated but the levitation of only a few metal compounds has been reported. Jostsons13 and the authors have levitated liquid titanium-oxygen alloys containing 50 at. pct 0 while clark14 has reported the levitation of mixtures of FeS and MnS for short periods. With a "cold crucible" inductor sterling15 has melted ferrites by preheating them by induction in a 4 mHz field and melting at a lower frequency. However this second type of inductor has been designed purely for the melting of materials without contamination; there is only a small gas film between the charge and the inductor and the electromagnetic levitation effect is of secondary importance. For this reason further discussion will be restricted to the use of the coil type inductor. The assessment of the suitability of a particular metal compound for levitation is based upon the following two criteria: i) thermal stability, and ii) physical "levitability". In this paper these two criteria will be considered separately. The thermal stability of a solid or liquid metal compound with respect to a gaseous environment depends upon its chemical reactivity with that environment or, in the case of an inert atmosphere considered here, its volatility. The physical criterion as to whether or not a particular compound can be levitated is based upon a comparison between those physical properties of the compound determining "levitability" which are defined by the fundamental equations of levitation theory as developed by Okress et a1.,16 and the properties of the metals. Since it is not practical to cover the vast field of metal compounds, further discussion will concentrate on the metal sulfides but the treatment would be applicable to any metal compound. THE THERMAL STABILITY OF METAL SULFIDES The temperatures usually encountered during levitation in inert atmospheres cover the range 1400" to 2000°C. The stabilities of the condensed states of the sulfides under these conditions are considered in relation to the periodic classification by reference to Table I. Two general classes of sulfides emerge. The solid sulfides of elements of group IIB and of groups further to the right are volatile while those sulfides of group IB and of groups further to the left are nonvolatile solids. The sulfides described as volatile may be dismissed as unsuitable for levitation. The stabilities of the more favorable nonvolatile sulfides under the anticipated conditions must be studied more closely From Table I it is seen that the alkali metal sulfides exist as liquids in the temperature range of in-

Jan 1, 1970

By F. H. Froes, D. H. Warrington

Electron microscope evidence which indicates that TaC may precipitate at random sites in the matrix is presented. Initially the particles are almost spherical and coherent with the matrix. However, as they grow in conditions in which there are insufficient vacancies to relieve lattice strain, the particles rapidly lose coherency in two directions and continue to grow as plates with approximately the full lattice mismatch strain present perpendicular to the plane of the plate. The necessary relief of strain comes from dislocations loops which do not become visible until the later stages of aging. The rapid decrease of apparent strain to low values of appoximately 1 pct at small particle sizes arises not from a complete incoherency but from applying a model wrong for the particle shape and strain distribution. PREVIOUS work has shown that MC-type carbides may precipitate intragranularly in austenitic stainless steel on dislocations,1&apos;2 in association with stacking faults,3&apos;4 and randomly through the matrix,5-7 In investigations of the matrix precipitate by thin-foil electron microscopy, considerable lattice strain has been found to occur around the precipitating phase.7&apos;8 Attempts have been made to evaluate the amount of lattice strain by using the methods developed by Ashby and brown.9,10 Values of the linear strain, much less than the 17 pct theoretical mismatch (for TaC), have been reported; it has been suggested that this is due to either a loss of coherency1&apos; or vacancy absorption which occurs during either the initial nucleation or growth of the precipitate." This report is an extension of earlier work7 that dealt with the precipitation of TaC from an 18Cr/12Ni/ 2Ta/O.lC alloy after it had been quenched from 1300°C and aged between 600" and 840°C. In particular, the shape of the precipitate particles and the amount of strain in the matrix, due to the precipitate, have been studied. The work described here is part of a wider investigation of factors that affect carbide precipitation in austenitic stainless steel," details of which are to appear elsewhere. RESULTS The present investigation can be conveniently split into two aspects of the strain-fields surrounding the matrix particles: 1) information derived from the strain-field which indicates the shape and habit plane of the precipitate particles and 2) the magnitude and sign of the strain-field. The Shape and Habit Plane of the TaC Precipitate. In the early stages of aging twin lobes (normally black F. H. FROES, formerly at the University of Sheffield, Sheffield, England, is Staff Scientist, Colt Industries, Crucible Materials Research Center, Pittsburgh, Pa. D. H. WARRINGTON is Lecturer, Department of Metallurgy, University of Sheffield. Manuscript submitted November 1, 1968. IMD on white background, i.e., for the deviation parameter, S > 0) that indicate the strained region of the matrix define the position of the particles by bright field transmission electron microscopy. The actual particles were not detected until they were approximately 120Å diam; below this size they were too small to be imaged in the electron microscope. This meant that particle growth that had occurred before this stage had to be inferred from the matrix strain-field contrast. In all cases when diffraction effects were observed from the precipitate particles, a cube-cube orientation relationship (i.e., (llO)ppt Il<llO>matrix and {1ll }ppt {III} matrix) existed between the precipitate and the matrix. From the matrix precipitate particles lying along edge-on {111} planes (e.g., at A, Fig. I), the precipitates are seen to be plate-like with their diameter being roughly 18 times their thickness after 5000 hr at 650°C. However, the exact shape of the particles cannot be determined because of the masking effect of the strain-field contrast. If a dark-field micrograph, using a precipitate reflection, is studied, Fig. 2, a number of the projected images of the TaC particles [on the (110) foil surface] apear to have straight edges parallel to projected f111) planes. Thus, it appears that in the later stages of aging the TaC particles are plate-like with some tendency for the edges of the plate to be bounded by the matrix close-packed {ill} planes (though the general shape of the particles in the plane of the plate is circular and thus the "diameter" of the particles has a real physical significance). It should be noted that the bands of fine discrete particles observed in Figs. 1 and 2 are not the matrix precipitate discussed in this paper but are precipitates associated with extrinsic stacking faults3j4 occurring on (111) matrix planes. **£** ****** \ *x 23 Fig. 1—18/12/2~a/0.1~ alloy. Solution treated at 1300°C for 1 hr, water quenched, and aged 5000 hr at 650°C. The (112) directions shown are the traces of the e&e-on (111) planes. Foil normal [110]; operating reflection (331); bright field micrograph.

Jan 1, 1970

By N. Standish

Heat transfer coefficients have been measured in beds of various packings irrigated with mercury and molten fusible alloy countercurrent to hot gases. The measured coefficients for both systems were found to increase with gas velocities and liquid rates. Correlations were determined which show this dependence and also indicate that heat transfer in these systems is influenced by the liquid flow characteristics and the thermal conductivity of the gas and the solid packings. A heat transfer model has beer2 proposed which explains the various features of the experimental results. On the basis of this study, which gives an insight into the heat exchange in the melting zone of the blast furnace, it was concluded that by comparison with the furnace stack heat transfer coefficients are about 1.5 times higher in the melting zone. EACH year large tonnages of metal are produced in operations which, in part, involve liquid metal irrigation of "packings" countercurrent to hot gases. The melting zone in blast furnaces and in cupolas is a good example of packings irrigated with a liquid melt countercurrent to gases. In all instances of this kind large amounts of heat are exchanged and it is desirable to have some knowledge of heat transfer phenomena involved in these systems. So far the most common method of analyzing furnace efficiencies, fuel requirements, and the general thermal state of the furnace has been through the use of heat balances. As heat balances are essentially statements of the first law of thermodynamics they give no real indication of the factors which govern heat transfer between phases in the various zones of blast furnaces. Hence, rational improvement in production efficiency and the development of theoretical models is only possible if the heat transfer characteristics are known at every stage of the process and related to the important variables involved. This has been generally recognized for some time but it was only recently that Kitaev et al.&apos; have produced a comprehensive treatment of heat transfer in solid-gas countercurrent systems such as the blast furnace stack and the packed bed regenerator. Using their treatment it is now possible to predict the effect of particle size, thermal conductivity, bed porosity, and the flow rates of both the gas and the solid material on the heat transfer in the blast furnace stack. However, the stack of a blast furnace is only one part of an integral unit for which the heat transfer analysis cannot be complete without also considering the heat exchange in the melting zone. The complexity of heat transfer processes in this region of the furnace has so far escaped quantitative description. Yet, the melting zone accounts for a greater amount of heat exchange than all the other zones of the furnace put together. Moreover, if the reduction of oxides in the melting zone proceeds in part in the liquid state the importance of heat transfer on furnace productivity and on the metal and slag temperatures is obvious. THEORY Heat transfer for two-phase flow in packed beds is a complex problem involving a number of heat exchange paths for which interphase areas are not known with any degree of certainty. Analytical solution is, therefore, difficult. This difficulty is emphasized by noting that Rabinovich~ and Luck have only recently solved the steady-state heat transfer for simplified two-phase heat exchangers of known area. However, useful progress can be made for the system considered by making a not unreasonable assumption that the usual heat transfer considerations apply and restricting treatment to the steady state. For these conditions the rate of heat transfer dq in a height dz of a packed bed of unit area is: dq = UaATdz [I.] Integration of Eq. [I] then gives the total heat transferred: assuming both U, the overall heat transfer coefficient, and a, the interphase area, to be independent of bed height. Since a, in these systems, is unknown it is convenient to combine this term with U. The group U, then represents the overall heat transfer coefficient on a volumetric basis. If AT is linear with q, then for a bed of unit volume Eq. [Z] can be integrated to give: is the log mean of terminal temperature differences. From Eq. [3] U, can be readily calculated as q and {AT)im are experimentally obtained quantities, but a difficulty arises in interpreting its meaning. Two approaches are possible depending on whether the effect of packing in the transfer of heat is neglected or not. If the packing is thermally decoupled then the resistance concept gives the relationship: which states that the overall resistance is the sum of the gas phase and the liquid phase resistances (assuming areas are equal throughout). Because the resistance to heat transfer in liquid metals is negligible by comparison with that of the gas,4 Eq. [4] can be simplified, i.e.:

Jan 1, 1969

By D. G. Westlake

Polycrystalline tensile specimens of various Zr-0-H alloys have been tested at 298°, 178°, and 77°K. Solute oxygen and hydride precipitates in quenched alloys made individual contributions to the yield strength at 0.2 pct strain which combined to produce a resultant strength increment, a,., Ductility changes which were ohserved can he interpreted in terms of the various oxygen and hydrogen concentrations, testing tem -peratures, and dispositions of the hydride. ADDITIONS of oxygen in solid solution were known to increase the yield and tensile strengths of polycrystalline zirconium as early as 1951.&apos; More recently, the critical resolved shear stress (CRSS) for prism slip in zirconium single crystals was also shown to be affected by the solute oxygen impurity.&apos; This latter work also demonstrated that large increments of strength could be contributed by the finely dispersed zirconium hydride precipitates that are present in quenched Zr-H alloys.3 It was concluded that the combined strengthening due to alloying could be expressed by where to is the increase in the CRSS due to solute oxygen alone and TH is the increase due to finely dispersed hydride precipitates. Eq. [I] is analogous to one used to express the combined strengthening effects of work hardening and neutron radiation damage.4 Eq. [1] was verified only indirectly and for only small amounts of the impurities—up to 0.14 at. pct 0 and 0.63 at. pct H. The present investigation was undertaken to obtain a more direct verification of the validity of the form of Eq. [1] for this system and also to determine the combined effects of oxygen and finely dispersed hydride precipitates on the tensile strength and ductility of polycrystalline zirconium. EXPERIMENTAL PROCEDURE Tensile specimens were machined from the same rolled billet of Kroll zirconium used in the earlier study.&apos; These measured 38 by 4.7 by 0.5 mm and had 10-mm gage lengths which were 2.8 by 0.5 mm. Each specimen was ß-annealed in vacuo at 1173°K for 15.5 hr and a-annealed at 1073°K for 4 hr to D. G. WESTLAKE, Member AIME, is Associate Metal l ur-gist, Metallurgy Division, Argonne National Laboratory, Argonne, III. Manuscript submitted July 17, 1964. IMD______________ give an equiaxed structure with grain diameters averaging 0.06 mm. Oxygen was added by allowing the metal to react with a known quantity of oxygen during the 0 anneal and known quantities of hydrogen were added during the a anneal. Each alloy was encapsulated in Pyrex under vacuum, annealed at 873°K for 4 hr, quenched into ice water, and polished by immersion in a solution of 46.75 vol pct H2O, 46.75 vol pct concentrated HNO3, and 6.5 vol pct HF (49 pct) at 298°K. Special heat treatments given to a few specimens are described in the results below. Tensile tests were done on an Instron machine and were begun within 20 min after the quench, except where specified otherwise. Tests at 298°K were in air, at 178°K in acetone, and at 77°K in liquid nitrogen. All tests were at a strain rate of 8x sec-1. RESULTS AND DISCUSSION Yield Stress at 298°K. The compositions of alloys and the corresponding yield stresses (0.2 pct strain) are given in Table I. A plot of the yield stresses of the oxygen alloys, A, B, C, and D, indicates that varies linearly with CO1/2, where Co is the oxygen concentration, Fig. 1. This is in accord with Fleischer&apos;s6 theory for solution strengthening if the oxygen atoms do not cluster, or the cluster size remains constant with increasing oxygen concentration. In Fig. 1, it appears that if one could prepare some oxygen-free zirconium its yield stress would be very low. Therefore, we shall assume that for the oxygen alloys is equivalent to O0, the strength increment contributed by the presence of oxygen. The relationship between0.2and Co is expressed by 0.2 = 31.3 CO1/2, when the yield stress is in kg per sq mm and the concentration is in at. pct. Each of the hydrogen alloys, Al, A2, A3, and A4, contained 0.081 at. pct 0 as an impurity. In Fig. 1, it appears that this small amount of oxygen makes a significant contribution to the strength which cannot be ignored when we evaluate the contribution of the finely dispersed hydride. Let us assume the validity of the following equation: a0.2 = (a2o+a2R)1/2 [2] which is analogous to Eq. [I] for single crystals, and calculate values of UH for the hydrogen alloys by using the experimental values of 0.2 and o (0.081 at. pct) = 8.9 kg per sq mm. For 0.36 at. pct H, oH = 6.47; for 0.72 at. pct H, OH = 11.30; for 2.16 at. pct H, OH = 19.4; and for 3.60 at. pct H,

Jan 1, 1965