Search Documents

By Haydn H. Murray

The term clay is somewhat ambiguous unless specifically defined because it is used both as a rock term and as a particle size term. Actually most persons using the term clay realize that it has a double meaning and in most instances define it. As a rock term, clay is difficult to define because of the wide variety of materials that compose it so that the definition has to be general. Clay is a natural, earthy, fine-grained material composed largely of a limited group of crystalline minerals known as the clay minerals. Many definitions state that a clay has the property of plasticity when wet, but some clays are not plastic, i.e., halloysite and flint clay; however, most clay materials are plastic when wet. As a particle size term, clay is used for the category that includes the smallest particles. The maximum size particles in the clay size grade are defined differently on some grade scales. Soil investigators and mineralogists generally use 2 microns as the maximum size. The Wentworth scale' defines clay as material finer than approximately 4 microns. Grim' has found it convenient to use the term clay material for any fine-grained, natural, earthy, argillaceous material and in this way can include clays, shales, or argillites, and some soils if they are argillaceous. Even though no standard definition of the term clay is accepted by geologists, agronomists, engineers, and others, still the term is generally understood by all who use it. Clay is an abundant natural raw material and has an amazing variety of uses and properties which will be discussed in this chapter. In order to understand better the relationships between the clays and their uses, a brief discussion of the structure, chemical composition, and identification of the clay minerals is given. Mineralogical Composition of Clays Clays are composed of certain groups of hydrous aluminum, magnesium, and iron silicates that may contain calcium, potassium, and other ions, which are called the clay minerals, and other minerals of variable composition, which are nonclay minerals. Both clay minerals and nonclay minerals influence the properties of a clay material. In order to understand the relationship between clay minerals and the properties of a clay material, a short summary of the structure and composition of clay minerals is necessary. Any scheme of classification tends to impose a certain rigidity and as new and additional data become available it is necessary to revise classifications. Brindley3 has discussed the classification and structural mineralogy of clays in very lucid fashion and chose a classification based on structural features and chemical composition. Grim2 proposed a tentative classification which is based on the structural attributes of the various clay minerals. This classification is relatively simple and workable, and is shown as follows: I. Amorphous Allophane group II. Crystalline A. Two-layer types (sheet structures composed of units of one layer of silica tetrahedrons and one layer of alumina octahedrons). 1. Equidimensional Kaolin group kaolinite, dickite, nacrite 2. Elongate Halloysite group

Jan 1, 1960

By M. C. Leverett, M. E. True, W. B. Lewis

This paper states the theory underlying the design of two kinds of dimensionally scaled models of parts of idealized oil fields. One of these simulates an oil well and its surrounding sand for a distance of 16 ft. radially from the well. The other model simulates linear flow through layered sands. Construction and operation of the models are described and typical data are given. The unique features in the design of the models are: (I) the treatment of the permeability-viscosity quotient as a single variable and (2) the use of previously reported experimentally developed relations between relative permeability and saturation and capillary pressure, saturation, porosity, permeability and interfacial tension. The models at present simulate flow of oil and water only, through unconsolidated sands. They are superior to unscaled models, which may give rise to erroneous conclusions. The models are designed to study the desirability of various methods of well completion and the effects of various factors on recovery of oil from layered sands. Introduction Recent work on the fundamental behavior of flowing mixtures of fluids in sands has resulted in the development of some new theory in this field, much of which has been presented in previous papers.l-4 However, the application of this theory to the behavior of oil wells or oil fields has proved too complicated for ordinary mathematical techniques, except in very highly simplified cases. A practical solution to this problem appears therefore, to lie in the use of dimensionally scaled models of elements of oil fields. The object of this paper is, first, to present the theoretical and experimental basis of the design of such models, and, second, to describe their construction and operation. Experiments now under way on the models already built will yield material for other reports, which will be devoted to interpretation of the results in terms of oil-field behavior. So far, simple dimensional models of two kinds have been built and are being operated. These models represent different parts of an idealized oil field but obey the same underlying theory. The only fluids represented are oil and water, since certain questionable approximations are necessary for gas-liquid systems. General Theory Dimensional models have been used in other fields for a long time, and their theory is adequately given in the literature. 5 Here, it suffices to state that each physical element entering into a dynamic relation may be given a definite description in terms of three fundamental, but arbitrarily chosen, dimensions. These usually are mass, length, and time, symbolized here by the small letters m, I, and t. Two systems are said to be dimensionally similar or dimensionally scaled if for each element in one system there is a corresponding element in the second system and the ratios of the numerical magnitudes of corresponding elements are constant for all elements of the same dimensional type.

Jan 1, 1942

By W. B. Lewis, M. E. True, M. C. Leverett

This paper states the theory underlying the design of two kinds of dimensionally scaled models of parts of idealized oil fields. One of these simulates an oil well and its surrounding sand for a distance of 16 ft. radially from the well. The other model simulates linear flow through layered sands. Construction and operation of the models are described and typical data are given. The unique features in the design of the models are: (I) the treatment of the permeability-viscosity quotient as a single variable and (2) the use of previously reported experimentally developed relations between relative permeability and saturation and capillary pressure, saturation, porosity, permeability and interfacial tension. The models at present simulate flow of oil and water only, through unconsolidated sands. They are superior to unscaled models, which may give rise to erroneous conclusions. The models are designed to study the desirability of various methods of well completion and the effects of various factors on recovery of oil from layered sands. Introduction Recent work on the fundamental behavior of flowing mixtures of fluids in sands has resulted in the development of some new theory in this field, much of which has been presented in previous papers.l-4 However, the application of this theory to the behavior of oil wells or oil fields has proved too complicated for ordinary mathematical techniques, except in very highly simplified cases. A practical solution to this problem appears therefore, to lie in the use of dimensionally scaled models of elements of oil fields. The object of this paper is, first, to present the theoretical and experimental basis of the design of such models, and, second, to describe their construction and operation. Experiments now under way on the models already built will yield material for other reports, which will be devoted to interpretation of the results in terms of oil-field behavior. So far, simple dimensional models of two kinds have been built and are being operated. These models represent different parts of an idealized oil field but obey the same underlying theory. The only fluids represented are oil and water, since certain questionable approximations are necessary for gas-liquid systems. General Theory Dimensional models have been used in other fields for a long time, and their theory is adequately given in the literature. 5 Here, it suffices to state that each physical element entering into a dynamic relation may be given a definite description in terms of three fundamental, but arbitrarily chosen, dimensions. These usually are mass, length, and time, symbolized here by the small letters m, I, and t. Two systems are said to be dimensionally similar or dimensionally scaled if for each element in one system there is a corresponding element in the second system and the ratios of the numerical magnitudes of corresponding elements are constant for all elements of the same dimensional type.

Jan 1, 1942

By Yves Dardel

The literature concerning the remelting of alunlinum and its alloys is very rich. Unfortunately the majority of the papers on this subject have no scientific value, for the theories or explanations are too often in opposition to the laws of physical chemistry. Furthermore only a few of the methods of purification are considered in the literature. Hence it has seemed necessary to the author to sketch a general theory of the purification of secondary aluminum. The purpose of the purification is to eliminate the impurities that the charges, and the atmosphere of the furnaces bring into the bath during the successive remelt-ings. Indeed scrap as well as metal can be used when soiled with oil, greases, water, or others, if it has been sufficiently dried and contains oxides. At the melting point of the metal, the oils and greases are decomposed into their constituent elements H², O2, H²O, co², CO, CH,, and others. These gases are added to the corresponding gases in the atmosphere of the furnace. The impurities introduced into the metal during the remelting will accordingly be the products resulting from the action of these gases on the liquid bath. The quantity of hydrogen that is soluble in aluminum and its alloys is given by the relation of sieverts3 as a function of its partial pressure PH2 in the atmosphere m = K vPH² [I] where K is a constant, which depends only upon the temperature and increases with it. The experiments of Rijntgen and Braun4, RÖntgen and M611er5, Bircum-shaw6 and Winterhagerl have rendered it possible to determine the value of K, when the temperature is less than 1.000°C. One obtains: log K = - 4,702.5T + o 238 [2] Besides its usual significance, the term Ph~ represents also the internal pressure of dissolved hydrogen, since in the equilibrium, that is1 when no gas exchange Occurs between the two phases, the Pressures of hydrogen in the metal and in the atmosphere must be equal. Eq I shows that when the partial pressure of H2 increases the amount of dissolved hydrogen in equilibrium increases, and that, if the contrary Occurs, the quantity of H² should diminish. However, if for any reason the diffusion of hydrogen is hindered and the total amount of dissolved gas remains constant while the temperature decreases, the internal pressure of H² increases until it reaches the value of the hydrostatic pressure. At this point, bubbles of hydrogen appear in the bath and escape out of it. The amount of hydrogen in the metal is then limited by a a depending On the hydro- static pressure, which is practically equal to one atmosphere. Indeed hydrogen does not accumulate in the form of a hydride appearing as a separate solid phase. However1 even the mechanism of the solubility is not yet elucidated. One does not know exactly as yet, whether the

Jan 1, 1949

By C. F. Clausen

"Cement" means binding agent or glue. It is derived from the Latin word "Caementum," the name of a limestone, chips of which were used in mortar more than 2,000 years ago in Italy. During the middle ages "cement" or "cement" generally denoted mortar. Today it means any binding material. The Thomas Register lists nearly 200 classifications for "cement" including automobile cement, household cement, rubber cement, etc. The material most commonly associated with this word, however, is portland cement which, when mixed with water and allowed to hydrate, is a ceramic binding material used to cement aggregates (crushed stone, gravel and sand) together in "concrete," the most universally used building material of today. It is estimated that more tons of concrete are used annually than all other building materials put together including steel, lumber, gypsum, bricks, tiles, aluminum and glass. Its use in foundations, building construction, sanitary work, dams, railroads, and highways, makes it difficult to conceive of modem civilization without concrete. A survey made in October 1955 showed the following uses of portland cement: [Percent Highways20 Nonresidential buildings20 Residential buildings15 Military construction10 Sewer and water works8 Public utilities10 Other (conservation, farm, and maintenance and repair)17 100] As of today, the percentage for highways is probably even higher. Ceramic binding materials have unquestionably been used in construction work for thousands of years. The mortar between the blocks of the great pyramids was calcined gypsum (plaster of paris). The use of calcined and slaked limestone goes back earlier than the Roman Empire. Gypsum, however, is relatively soft, and common lime mortar is not "hydraulic," i.e., it does not harden under water. The Greeks and Romans discovered later that an addition of a finely divided active siliceous material (Santorin earth or Pozzolana) would react with slaked lime to form a stronger, and hydraulic, cement. The Appian Way in Italy, Colosseum, and the great Aqueducts built by the Romans were made with this type cement, and some of these structures are still in existence today. However, not until 1756 did some serious research result in the development of better cements. In that year the English engineer, John Smeaton produced a stronger cement by burning a limestone containing considerable proportions of clayey impurities. Other investigations and improvements were made by Bryan Higgins, Bergmann, Joseph Parker, L. J. Vicat, J. F. John, James Frost, and I. C. Johnson.2 Traditionally, but perhaps unfairly to others, the invention of the prototype of today's portland cement is credited to the English mason Joseph Aspdin who in 1824 obtained a patent and gave the product its name, because in color the mortar produced from it resembled a natural building stone obtained from the British Isle of Portland. The contributions of Johnson and Aspdin were primarily the important step of preparing a synthetic mixture of lime and clay without depending on raw materials found in nature which might contain such elements in desirable proportions. However, even these early

Jan 1, 1960

By J. S. Bryner

In the study of metallographic specimens in the electron microscope, there is need for a method of locating the same field in both the light microscope and the electron microscope. This need arises chiefly from the fact that in the electron microscope the magnification and degree of resolution are so much higher, and the field so much smaller than in the light rnicroscope that it is often difficult, if not impossible, to identify positively what is being observed. The difficulty is increased by the fact that, because a transparent film replica of the metal surface must be used in the electron microscope, micro-constituents can be identified not by their color but only by their texture and contours. For these reasons it is desirable to obtain a series of photographs showing the same field in both microscopes in order that the appearance of common microstructures and micro-constituents in the electron microscope may be identified and catalogued for future reference. The need for a method of locating the same field in both microscopes arises also when it becomes desirable to enlarge in the electron microscope for more detailed study a particular interesting structure observed in the light microscope. Using the standard polystyrene-silicalJ replica technique, in which the silica film replica is fished from the ethyl bromide on a 1/8 in. diam zoo-mesh specimen screen, the possibilities of locating a particular area on the film in the electron microscope are rather remote. The desired structure may be obscured by the wires of the specimen screen or unrecognizable at the high magnification. A solution to the problem would be provided if a specially designed specimen screen, containing an opening which could be absolutely identified and quickly located in the electron microscope, could be fastened to the silica film replica in such a position that the desired field on the specimen would be located at the identifiable opening in the specimen screen. The design for such a specimen screen, a method for producing it, and a technique for fastening it to the silica film replica are described below. Description OF Method The Specimen Screen A simple design for a specimen screen containing an opening easy to identify and locate in the electron microscope is one with two lines of openings at right angles in the form of a cross. Such a screen is shown in Fig I. The opening at the center of the cross is identified easily and can be located quickly in the light microscope and in the objective image of the electron microscope. The specially designed specimen screens for this work were produced in quantity by electroforming. On both sides of a polished strip of copper I X 3 X 1/8 in., twenty patterns of the cross of openings were punched with a diamond point micro-hardness tester, using a load of magnitude

Jan 1, 1949

By G. B. Walker, S. J. Swainson, S. A. Falconer

DURING the past few years much interest and attention has been focused on a relatively new method of ore concentration, which utilizes the principles of sink and float and employs as the heavy medium a suspension in water of a finely ground solid, such as galena or ferrosilicon. Although a relatively recent development, much progress has already been made in applying heavy-media separation processes to a considerable number of ores. Eight plants in this country and abroad -are now treating approximately 10 million tons of ore annually by heavy-media separation (sink-float) processes, including lead-zinc, lead, iron, garnet, tin and tungsten. At the annual meeting of the A.I.M.E. in 1941, three interesting papers (unpublished) dealing with heavy-media separation (sink-float) processes of ore concentration as practiced in four commercial units in the United States were presented by Victor Rakowsky, Grover Holt, Elmer Isern and Robert Ammon. These papers gave an excellent exposition of the principles of sink and float, as well as the operating practice in two iron-ore-beneficiation plants, the Harrison and the Merritt, of Butler Brothers, in Minnesota; the Central mill of the Eagle Picher Mining and Smelting Co.; and the Mascot mill, of the American Zinc, Lead and Smelting Co. Augmented by pictorial descriptions and a working model demonstrating the processes, these papers evoked a great deal of interest and discussion. In fact, in reporting the high lights of the meeting in the April 1941 issue Of MINING AND METALLURGY, Professor Taggart made the statement that "preconcentration by heavy suspension was Miss A.I.M.E. 1941 so far as milling is concerned." Although to date the greatest application of heavy-media separation from the tonnage point of view has been for the treatment of lead, zinc and iron ores, these processes have a much wider field of usefulness. In this regard, it is to be noted that recently new heavy-media separation plants for treating cassiterite ore and garnet ore have been placed in successful operation. Moreover, numerous other types of ores have been found to respond well to these processes when tested on a semi-commercial scale, and it is expected that in the near future a considerable number of new plants will be erected. In view of the fact that heavy-media separation processes offer such attractive possibilities, particularly now, when the mining industry is being called on for an even larger production than ever before has been attempted, despite shortages of labor and supplies, it was felt that a description of some of the successful separations that have been worked out during the past year in the Ore Dressing Laboratory of the American Cyanamid Co. on a variety of ores of strategic importance would be of interest. The purpose of this paper, therefore, is to present the essential data relating to investigations of heavy-

Jan 1, 1943

By M. King Hubbert

In 1856 Henry Darcy described in an appendix to his book, Les Fontaines Publiques de la Ville de Dijon, a series of experiments on the downward flow of water through filter sands, whereby it was established that the rate of flow is given by the equation: q= - K(h2- h2)/I1 in which q is the volume of water crossing unit area in unit time, I is the thickness of the sand, h1 and h2 the heights above a reference level of the water in manometers terminated above and below the sand, respectively, and K a factor of proportionality. This relationship, appropriately, soon became known as Darcy's law. Subsequently many separate attempts have been made to give Darcy's empirical expression a more general physical fornzulation, with the result that .so many mutually inconsistent expressions of what is purported to he Darcy's law have appeared in published literature that sight has often been lost of Darcy's own work and of its significance. In the present paper, therefore, it shall be our purpose to reinform ourselves upon what Darcy himself did, and then to determine the meaning of his results when expressed explicitly in terms of the pertinent physical variables involved. This will be done first by the empirical method used by Darcy himself, and then by direct derivation from the Navier-Stokes equation of motion of viscous fluids. We find in this manner that: q = (N4(p/p)[g - (l/p) gradPI = WE, is a physical expression for Darcy's law, which is valid for liquids generally, and for gases at pressures higher than about 20 atmospheres. Here N is a shape factor and d a characteristic length of the pore structure of the solid, p and IL are the density and viscosity of the fluid, a = (Nd2)(pip) is the volume conductivity of the system, and E = [g - (l/p) grad p] is the impelling force per unit mass acting upon the fluid. It is found also that Darcy's law is valid only for flow velocities such that the inertial forces are negligible as compared with those arising from viscosity. In general, three-dimensional space there exist two superposed physical fields: a field of force of charucteristic vector E, and a field of flow of vector q. The force field is more general than the flow field since it has values in all space capable of being occupied by the fluid. So long as the fluid density is constant or is a function of the pressure only, curl E = 0, E = - grad F where F = gz + dp/p The field of flow, independently of the force field, must satisfy the conservation of mom, leading to the equation of continuity div pq = — f ap/at , where f is the porosity, und t is the time. For steady rnotion ap/at = 0. and div pq = 0 .

Jan 1, 1957

By M. E. Nicholson

IT has been suggested by a number of investigators, I including Hume-Rothery and Raynor,' that certain intermediate phases in metal systems take on interstitial crystal structures because of an appropriate ratio of radii of the two atoms. If the size factor is an important parameter in determining whether or not an intermediate phase will have an interstitial structure, then it would appear reasonable that the relative sizes of interstitial atoms should have a direct relation to their solubilities in interstitial compounds. It was on such a basis that Petch,' in his discussion of the cementite structure, concluded that nitrogen is the only possible element which could replace carbon. Recent X-ray studies by Jacka indicate that the solid solubility of nitrogen in cementite is negligible. If this is the case, then on the basis of size factor it would not be expected that any element can replace carbon in FeaC, since according to Schwarzkopf and Kieffer4 the covalent atomic radii of nitrogen, carbon, and boron are 0.71, 0.76, and 0.87A, respectively. Nevertheless, Vogel and Tammann in 1922 indicated that a quasi-binary relation exists between the interstitial compounds FeaC and Fe2B and that the solid solubility of boron in FeaC at approximately 1150°C is 1.4 pct B by weight. Because of the apparent disagreement between theory and experiment, the solid solubility of boron in FeaC has been reinvestigated. In addition, the influence of boron on the saturation magnetic moment (per gram) and Curie temperature of cementite was determined. Experimental Procedure A series of Fe-B-C alloys which varied in boron content from 0 to 5.4 wt pct B were prepared by arc melting a 50-g ingot using carbonyl iron, Ache-son AUC graphite, and Cooper grade A boron for starting materials. The composition of these alloys is listed in Table I and shown graphically in Fig. 1. The samples represented by the solid circles were used for X-ray analysis and Curie temperature measurements; by the squares, samples used for quantitative metallography; and by the triangles, samples used for saturation magnetic moment measurements and Curie temperature measurements. After arc melting and subsequent quenching from 1000°C, so that all phases in the resulting microstructure were brittle, one half of the 50-g ingots were pulverized until a powder was obtained which was less than 100 mesh. These powders were then homogenized in evacuated Vycor capsules at 1000°C for 24 hr and water quenched. Although the homogenized powder had sintered somewhat, it was suitable for saturation magnetic moment and Curie temperature determinations, for which the 60 to 100-mesh fraction of the powder was used. For X-ray analysis the homogenized powder was crushed again until a 300-mesh powder was obtained. After crushing, the powder was mixed with Alundum of approximately the same grit size to prevent sinter-

Jan 1, 1958

By E. J. Valyi

The purpose of the continuous casting processes is twofold: As the name implies, they aim at performing a heretofore intermittent operation continuously; in this respect, they tend to satisfy the appetite of the beast that modern extrusion plants and rolling mills have grown to be. The effort invested in the development of these methods bore rich dividends in economy and in the improvement of technical characteristics. The other purpose of many continuous casting methods is to reduce the number o-f operations mushrooming between the liquid alloy and the finished mill product, essentially by substituting adequate chill in comparatively small cross sections for one or more "breakdown" steps. It is this second tendency of continuous casting that justifies description of the Soro process within the frame of our symposium: although not continuous, the Soro method constitutes a means of converting molten metal into a nearly finished mill product. The Process The name, Soro, is a composition of initials and abbreviations, with no particular technical significance. The process originates in Switzerland; it was adopted by numerous European plants between 1937 and 1940 and is now being installed in this country. It is applicable to ferrous and nonferrous alloys of an exceptionally wide range of composition. It is capable of producing rod from 1/2 in. to approxi- mately 4 in. in diameter, or other simple solid shapes of corresponding cross-sectional area. , Fig. I shows schematically the succession of operations involved. A ring is cast in a two-part centrifugal-casting metal mold. The cross section of the ring may be round, hexagonal, rectangular or some other solid shape, with the exception of any contour that is undercut with reference to the mold parting line. As cast, the ring has a riser along its inner periphery, which is removed in the next operation, so as to leave the ring with a dean cross section. Following the removal of the riser, the ring is severed at one point and one end is bent outward, leaving a slight clearance between the two ends. The next step is straightening of the ring in a special device, forming a bar with a slight bend; this is followed by any one of the conventional finishing operations that are necessary to obtain forging rod, screw-machine stock or strip. The outstanding features of this procedure are: I. The cross section cast is the same or within a few per cent of the cross section of the finished product (except for fabricating into strip and wire). 2. All operations following casting of the ring are performed cold. Equipment The equipment required is simple and inexpensive. The casting machine is a conventional horizontal-shaft mold assembly, similar to those found in centrifugal-casting foundries. Fig. 2 shows a battery of three machines- with their protecting hoods .swung open. One of these machines,

Jan 1, 1945

By H. H. Stout

In the early fall of 1925, the writer was conducting, in the Ledoux and Co. laboratory, New York, experiments directed toward ascertaining the effect on its impurity content when cathode copper was subjected to a current of various gases at an elevated temperature below the melting point. The apparatus consisted of a vertical I-in. dia. silica tube about 12 in. long, heated on the outside. The cathodes were broken to pass 3/8-in. mesh, and a current of various different gases was passed up through a 4-in. long column of these loose cathode particles in the vertical tube furnace. Temperature was maintained to 1500º to 1600ºF. and the gas treatments lasted from 3 to 6 hr. The writer observed that whenever reducing gas (H2 or CO) was used, these cathode particles stuck together at points of contact with each other. The cohesion was so marked and tenacious that an examination was made of the fractured surfaces, when cathode particles were broken from the cluster. Crystal growth was always found to have taken place across the surfaces where separate particles were in contact, but only after all oxides, sulphates, etc., had been completely removed. The idea of a possible new process was then conceived and was disclosed to A. M. Smoot (V. P. Ledoux and Co.) with intent to obtain his views. The first conception as given Smoot was "to gas-clean broken cathodes, put them in an extrusion press, solidify and extrude them at around 1500ºF." Smoot's reaction, after a few moments considera- tion, was, "It looks perfectly all right to me.'' The writer and his assistants, W. H. Osborn and H. H. Stout, Jr., after conferring as to ways and means, decided to go ahead with preliminary laboratory experiments, which, it was thought, would move the new process from the possible to the probable. This program followed a course indicated by three basic considerations: 1. Since brittle cathodes were often unintentionally produced, it seemed probable that the laws controlling this type of deposition could be ascertained. 2. We had already proved the gas-cleaning feature. 3. There remained to prove: whether a sound, homogeneous metal billet could be produced with crystal growth established over the entire surface of each individual particle in the billet; and, if so, what would be the physical properties? Osborn arranged with Columbia University for conducting experiments in its research laboratory to prove or disprove the third item; Columbia assigned C. A. Phillipi, Jr. to assist in the project. A press with a cylinder 2 in. high and of I-in. dia. was used. It was surrouilded and heated by a resistance coil 01 Nichrome wire. Broken tough cathodes were used. Experimental Procedure The first run took place March 18, 1926. The resistance wire gave out when temperature of 1000ºF. was obtained. Pressure was immediately applied: perceptible ram movement stopped when 39,000 lb. per sq. in. on the copper was reached, with a maxi-

Jan 1, 1941

By Hugh D. Pallister, Richard W. Smith

The Alabama flake-graphite industry has flourished only in times of war when importations of foreign graphite for crucible use have been greatly curtailed or cut off. World War I was a boom period and in 1918 some 30 plants produced 7,795,475 Ib. of flake graphite. The industry languished following the war and no graphite was produced from 1929 to 1939. The Federal Bureau of Mines began investigating the Alabama graphite deposits in 1940 and worked out modern recovery methods that were applied to production during part of World War 11. A prospecting program disclosed reserves of over 25 million tons of graphtic schists. In 1942 the War Production Board authorized the enlargement of the only plant then producing flake graphite and the construction of two new plants. Production of flake graphite from these three plants in 1943 is estimated at 8,100,000 lb. Increased imports from Madagascar late in 1943 shut down one of the new plants and curtailed production at the other. Alabama flake graphite has not yet been able to compete with Madagascar graphite for use in the manufacture of any but small graphite crucibles. The future of the industry must depend on meeting the higher carbon content demanded for other uses. Introduction The flake-graphite deposits of Alabama are confined to a narrow belt extending for about 60 miles southwest from the northeast corner of Clay County across Coosa County to the edge of the Coastal Plain in Chilton County (Fig. I). The continuity of the beds is broken by a 10-mile gap between Millerville in Clay County and Goodwater in Coosa County. The Clay County beds extend about 27 miles northwest of this gap, with a width of 3 to 4 miles near Millerville and of less than a mile at the northeast end. The Coosa-Chilton are? is about 33 miles long with a fairly consistent width of 2 to 3 miles. Geologically the graphite belt lies near the northeast boundary of the outcrop of metamorphic rocks of the Ashland series, a complex group of intensely folded and faulted beds of pre-Cambrian age composed mostly of quartz-mica schist, in which the mica is predominantly muscovite; garnet-mica schist, in which biotite is more common; and hornblende schist. Flake graphite is found in commercial quantities only in the quartz-mica schist. The best graphite, both in quantity and quality, is found in schist cut by numerous small pegmatite stringers along the planes of the schistosity. The pegmatites themselves contain little graphite, but the adjacent country rock is normally rich. . The schist was derived through the recrystallization of shale during the intrusion of the pegmatites, the graphite being derived from amorphous carbon in the shale. The intrusion of the pegmatites, and therefore the size and quantity .of the graphite flakes, seems to have a structural control.

Jan 1, 1948

By Hugh D. Pallister, Richard W. Smith

The Alabama flake-graphite industry has flourished only in times of war when importations of foreign graphite for crucible use have been greatly curtailed or cut off. World War I was a boom period and in 1918 some 30 plants produced 7,795,475 Ib. of flake graphite. The industry languished following the war and no graphite was produced from 1929 to 1939. The Federal Bureau of Mines began investigating the Alabama graphite deposits in 1940 and worked out modern recovery methods that were applied to production during part of World War 11. A prospecting program disclosed reserves of over 25 million tons of graphtic schists. In 1942 the War Production Board authorized the enlargement of the only plant then producing flake graphite and the construction of two new plants. Production of flake graphite from these three plants in 1943 is estimated at 8,100,000 lb. Increased imports from Madagascar late in 1943 shut down one of the new plants and curtailed production at the other. Alabama flake graphite has not yet been able to compete with Madagascar graphite for use in the manufacture of any but small graphite crucibles. The future of the industry must depend on meeting the higher carbon content demanded for other uses. Introduction The flake-graphite deposits of Alabama are confined to a narrow belt extending for about 60 miles southwest from the northeast corner of Clay County across Coosa County to the edge of the Coastal Plain in Chilton County (Fig. I). The continuity of the beds is broken by a 10-mile gap between Millerville in Clay County and Goodwater in Coosa County. The Clay County beds extend about 27 miles northwest of this gap, with a width of 3 to 4 miles near Millerville and of less than a mile at the northeast end. The Coosa-Chilton are? is about 33 miles long with a fairly consistent width of 2 to 3 miles. Geologically the graphite belt lies near the northeast boundary of the outcrop of metamorphic rocks of the Ashland series, a complex group of intensely folded and faulted beds of pre-Cambrian age composed mostly of quartz-mica schist, in which the mica is predominantly muscovite; garnet-mica schist, in which biotite is more common; and hornblende schist. Flake graphite is found in commercial quantities only in the quartz-mica schist. The best graphite, both in quantity and quality, is found in schist cut by numerous small pegmatite stringers along the planes of the schistosity. The pegmatites themselves contain little graphite, but the adjacent country rock is normally rich. . The schist was derived through the recrystallization of shale during the intrusion of the pegmatites, the graphite being derived from amorphous carbon in the shale. The intrusion of the pegmatites, and therefore the size and quantity .of the graphite flakes, seems to have a structural control.

Jan 1, 1948

By Hjalmar W. Johnson

It has long been accepted that blastfurnace practice varies to some degree with the coke used. While the qualities desirablc in iron have been known for some time, the qualities in coke that produce such iron have not been established. There are no objective standards for blast-furnace coke, which is usually described in general terms, as good or bad. Many experienced operators believe that coke cannot be measured objectively except by using it in the furnace, noting the result, and labeling the coke according to furnace operations. This is admittedly unscientific, and besides is useless for the two main purposes for which a measure of coke quality is needed: (I) to produce the best possible coke from the coals and equipment on hand; (2) to test new coals and determine their value for blast-furnace coke. In seeking such an objective measure, much work has been done on tumbler tests, shatter tests, sizes of coke, porosity, specific gravity, reactivity or combustibility and other tests, but as yet very little has been published in which conclusive correlations have been established between such objective measures and furnace operation. In our study of the problem during the past 8 years we have developed no new measures of coke quality, but we have collected data that are presented here in the hope that they may assist in further work, so that at some future time there may be developed such positive measures. The purpose of this paper is to show that there are variations in coke and that such variations do influence the operation of blast furnaces. At the same time we must remember that there are variations in blastfurnace operation and it may be the blast furnace that is at fault. This correlation of coke properties with blast-furnace operation will be worked out in the following steps: . Discussion of a period when a change in the coke resulted in an increase in efficiency on one furnace and a decrease in efficiency on another. 2. Adaptation of the inefficient furnace to the available coke so that normal efficiency was restored. 3. The use of radial distribution: a discussion of the effect of size of ore layer in adapting blast-furnace operation to the coke. 4. An example of a change in size of coke and the detrimental influence on the pro duction of one furnace. 5. An example of a change in size of coke, together with manufacturing data, to show why it changed, the conclusion being that coke is a product with an optimum value. 6. Illustration of the fact that coke has different optimum values on two furnaces, with discussion on adaptation of operation so the optimum values will be the same. 7. Limitations of the use of screen tests as an objective measure of coke quality. 8. Importance of uniformity in coke. Functions of Coke and Qualities Required to Perform These Functions Coke has three important functions in a blast furnace: (I) to furnish most of the

Jan 1, 1942

By Hjalmar W. Johnson

It has long been accepted that blastfurnace practice varies to some degree with the coke used. While the qualities desirablc in iron have been known for some time, the qualities in coke that produce such iron have not been established. There are no objective standards for blast-furnace coke, which is usually described in general terms, as good or bad. Many experienced operators believe that coke cannot be measured objectively except by using it in the furnace, noting the result, and labeling the coke according to furnace operations. This is admittedly unscientific, and besides is useless for the two main purposes for which a measure of coke quality is needed: (I) to produce the best possible coke from the coals and equipment on hand; (2) to test new coals and determine their value for blast-furnace coke. In seeking such an objective measure, much work has been done on tumbler tests, shatter tests, sizes of coke, porosity, specific gravity, reactivity or combustibility and other tests, but as yet very little has been published in which conclusive correlations have been established between such objective measures and furnace operation. In our study of the problem during the past 8 years we have developed no new measures of coke quality, but we have collected data that are presented here in the hope that they may assist in further work, so that at some future time there may be developed such positive measures. The purpose of this paper is to show that there are variations in coke and that such variations do influence the operation of blast furnaces. At the same time we must remember that there are variations in blastfurnace operation and it may be the blast furnace that is at fault. This correlation of coke properties with blast-furnace operation will be worked out in the following steps: . Discussion of a period when a change in the coke resulted in an increase in efficiency on one furnace and a decrease in efficiency on another. 2. Adaptation of the inefficient furnace to the available coke so that normal efficiency was restored. 3. The use of radial distribution: a discussion of the effect of size of ore layer in adapting blast-furnace operation to the coke. 4. An example of a change in size of coke and the detrimental influence on the pro duction of one furnace. 5. An example of a change in size of coke, together with manufacturing data, to show why it changed, the conclusion being that coke is a product with an optimum value. 6. Illustration of the fact that coke has different optimum values on two furnaces, with discussion on adaptation of operation so the optimum values will be the same. 7. Limitations of the use of screen tests as an objective measure of coke quality. 8. Importance of uniformity in coke. Functions of Coke and Qualities Required to Perform These Functions Coke has three important functions in a blast furnace: (I) to furnish most of the

Jan 1, 1942

By Jack White, Ralph B. Adair

The Mufulira mine in Northern Rhodesia is 13° south of the Equator and at an altitude of 4100 ft above sea level. The concentrator was planned in 1930 to treat about 10,000 tons of ore per day, but before construction work had gone very far the size of the plant was reduced to 1500 tons daily capacity. Then just as the construction was finished in December 1931, the price of copper did not warrant the commencement of operations and it was not until October 1933 that the mine re-opened. Extensions have been made to the plant in 1934, 1935, 1936, 1937, 1940 and finally in 1945. The capacity of the plant when the 1945 extension is completed will be 9500 short tons per day. The various extensions have been carried out with the minimum confusion and with great skill on the part of the designers and the erection engineers. In dealing with the plant in this paper it is proposed to give an outline of the present practice and only to refer to past practice when it is considered of particular interest. Ore Treated The ore consists of fine grained highly siliceous, felspathic and argillaceous quartz- ites, the latter containing graphitic carbon and locally termed graywacke. These rocks are considerably altered near the surface and on the fringes of the ore body. Despite extensive efforts at mixing, both underground and in the crushing plant, many sudden changes of ore take place in the mill feed. The minerals are chalcocite, bornite and chalcopyrite with relatively unimportant amounts of malachite, native copper, azurite, covellite and chrysocolla. Gold is present at about I oz to a thousand tons, and silver at about 2 dwt. per ton. With increasing depth the nonsulphide content or,, as commonly termed locally, the oxide content of the ore is decreasing and is now less than 0.25 pct against a high of 0.77 pct- Crushing Operations The first stage of crushing is done under. ground where the oversize from I2-in. grizzlies is fed to a 56 X 72-in. jaw crusher. At the Selkirk shaft two 10-ton skips deliver the run of mine ore at a rate of 450 tons per hour to the 400-ton capacity shaft bins. One 6 ft wide Ross chain feeder and one locally made air-operated finger feeder feed the two 30-in. McCully crushers. Ahead of each crusher is a 6 X 9-ft spring grizzley spaced at 5 in. on a 35O slope. Neither the Ross chain feeder nor the finger feeder is entirely satisfactory and for the wet, muddy and sticky ore that has to be handled it is planned to replace these with two 6-ft wide apron pan feeders. The McCully crushers deliver a minus 5-in. product, at a.rate of over 500 tons per

Jan 1, 1949

By H. F. Silliman, Daniel R. Hull, John R. Freeman

In the normal operation of a brass-rolling mill, sheet and strip has, for the most part, been finished in comparatively thin gauges, involving a substantial amount of cold-work and a considerable number of anneals. This condition has been disturbed by the preponderance of cartridge brass, which is not rolled to thin gauges, and particularly by brass for artillery cartridge cases, on which the mill may finish its work at a thickness between 0.400 and 0.900 in. Obviously, the amount of rolling and the number of anneals to which such a product can be subjected are small compared with strip that is carried to a thickness of a few hundredths of an inch. As a result, critical examination into the internal condition of metal has been made on an extensive scale at a stage of manufacture that would not, in normal times, have been chosen for complete inspection. Under these conditions, a type of defect has been recognized that is not seen at thinner gauges. It might be more accurate to call it the appearance of a defect, since it refers to an apparently laminated, discontinuous structure, which, in fact, does not exist as such, and disappears after suitable treatment. For this reason it has been called a phantom lamination, which the authors consider an appropriate term. It is the purpose of this paper to describe the phenomenon and the conditions of its occurrence and, at least tentatively, to discuss its nature and cause. Great numbers of phantoms may be found in 2:r brass, either hot-rolled or cold-rolled. They are also found in 70-30 brass, sometimes when hot-rolled and generally when cold-rolled. It is not believed that phantoms are confined to these alloys but this paper is limited to them for the purpose of description. Hot-rolled 2:1 Brass For illustration, therefore, a typical cake of hot-rolled 2:I brass has been chosen. This was rolled to a slab 36 in. thick, from a casting 5 in. thick by 24 in. wide by 18 in. high, which was believed to have been sound. After hot-rolling and cooling, the slab was sheared and a portion of such a shear cut is shown in Fig. I. It would be difficult to convince anyone viewing this specimen that the metal was not unsound. The impression would be confirmed by the appearance of a tensile break, as shown in Fig. 2. This is an ordinary tensile-test piece from metal just described. Although there was nothing in its tensile strength or elongation that suggested unsoundness, it appeared run through with pipes and laminations. To question the reality of such a condition would imply questioning the obvious. But, considering the history of the metal, it would be difficult to believe that it could be so bad as it appeared. It seemed reasonable, though, that if the defects were what they appeared to be, they could be traced back from the sheared or broken face.

Jan 1, 1945

By John A. Putnam, Morrough P. O’Brien

DATA on the physical and thermodynamic properties of hydrocarbons have been made available in recent years but the formal method of applying these data to flow in porous media appears not to have been fully developed. By making usual thermodynamic assumptions and employing existing data on permeability to two-phase flow, Darcy's law may be applied to obtain the flow characteristics for representative combinations of flowing medium and geometry. The numerical examples presented herein are based on hydrocarbons for which complete physical and thermodynamic data are available under equilibrium conditions. INTRODUCTION Thermodynamic data are obtained in the laboratory under equilibrium conditions and their application requires the assumption that equilibrium also exists during flow. This assumption is at least usual in engineering analyses, though not easily justified in many instances, and will be followed here. In regard to hydrocarbons, laboratory experience in determining the pressure-volume-temperature relationships indicates that gas-liquid mixtures must often be stirred vigorously for periods of 15 to 20 min. before reaching equilibrium. On the other hand, boiling and condensation are known to occur on solid surfaces and the large surface exposed to the flowing substance by a porous medium may bring about rapid approach to equilibrium. For the purpose of providing at least a guide to experimentation and a standard for later comparison with experimental results, it will be assumed that the phases present in cross sections perpendicular to the direction of flow are in thermodynamic equilibrium. Another assumption usually made in the solution of problems of flow in porous media is that the fluid remains at a constant temperature; i.e., isothermal flow. This assumption is arrived at by considering the porous medium and surroundings to be an infinite heat source and the rate of heat flow to be infinite at a boiling front. Its validity depends in large measure upon the character of flow, the number of components, and the physical and thermodynamic properties of the fluid. However, the assumption of isothermal flow represents a limiting case. The other limit can be represented by the assumption that the fluid is thermally isolated; i.e., irreversible adiabatic. The thermodynamic process characterizing the actual flow of a given fluid system probably lies somewhere between these two limiting cases and might be thought of as a flow system in which the confining walls are maintained at a constant temperature. For isothermal flow the solid material of the porous media is considered as the infinite heat source capable, without loss in temperature, of giving up heat to the fluid as the latter tends to cool by expansion. For the thermally isolated system, the solid material is considered to give up no heat to the fluid. In the intermediate case the impervious walls confining the porous media are at constant temperature from which heat is transferred along various paths, solid and fluid, throughout the porous media. It would appear that an actual petroleum-

Jan 1, 1941

By G. W. Jones, G. S. Scott

Economic waste caused by mine fires may become considerable,l5 especially if a fire is allowed to spread or temporarily to get beyond control. It is important, therefore, to act promptly whenever a fire is suspected and to make every action count. To contribute toward its extinction effectively it is necessary to know at the earliest possible moment, and continuously thereafter, what is happening at the seat of the fire, which may be in a remote or inaccessible area, and also to recognize what may be expected as a result of any proposed combative measure. In combatting a fire the mining engineer and the chemist should cooperate, first deciding upon the course of action to be taken and then drawing upon the mining engineer's intimate knowledge of the physical structure of the fire area, the cost and time required to carry out proposed operations, and the probable efficiency with which these operations could be performed, and upon the chemist's knowledge for the results to be expected therefrom. After the initial steps to be taken have been decided, it devolves upon the mining engineer to see that they are carried out and upon the chemist to evaluate the results and to keep the mining engineer continuously informed in regard to a variety of matters—such as the composition and toxic or asphyxiating properties of the atmosphere in which the men may be working, whether the fire is increasing or decreasing in intensity and its probable temperature, the quantity of air leakage and the explosion hazards of the fire area. The purpose of this paper is to discuss what the chemist can and cannot contribute as a member of the fire-fighting personnel. The technical literature contains several hundred papers relating directly and indirectly to mine fires, and this fact alone is testimony to the complex nature of the phenomena involved in the birth, life, and final demise of a fire. A fire may be stopped (I) by preventing oxygen from reaching the coal or (2) by removing the conditions necessary for the rapid reaction of coal with oxygen; i.e., decreasing the temperature. All methods of prevention or control necessarily must be based upon one or the other, or both, of these two principles. The chemistry of a fire may be understood readily if the low-temperature oxidation of coal is considered as a starting point; then oxidation at higher temperatures (or combustion); and with these, the composition of the solid and gaseous products resulting from the oxidation or from the effects of the heat liberated. This discussion refers particularly to Pennsylvania anthracite, although much of the material applies equally well to coals of lower rank. Oxidation of Coal Oxidation of coal fundamentally is confined to the surface; that is, the rate at which oxygen penetrates into the interior of a solid block of coal is so slow that it may be ignored."16 Oxidation starts when a fresh surface is exposed, and the rate is

Jan 1, 1942

By G. S. Scott, G. W. Jones

Economic waste caused by mine fires may become considerable,l5 especially if a fire is allowed to spread or temporarily to get beyond control. It is important, therefore, to act promptly whenever a fire is suspected and to make every action count. To contribute toward its extinction effectively it is necessary to know at the earliest possible moment, and continuously thereafter, what is happening at the seat of the fire, which may be in a remote or inaccessible area, and also to recognize what may be expected as a result of any proposed combative measure. In combatting a fire the mining engineer and the chemist should cooperate, first deciding upon the course of action to be taken and then drawing upon the mining engineer's intimate knowledge of the physical structure of the fire area, the cost and time required to carry out proposed operations, and the probable efficiency with which these operations could be performed, and upon the chemist's knowledge for the results to be expected therefrom. After the initial steps to be taken have been decided, it devolves upon the mining engineer to see that they are carried out and upon the chemist to evaluate the results and to keep the mining engineer continuously informed in regard to a variety of matters—such as the composition and toxic or asphyxiating properties of the atmosphere in which the men may be working, whether the fire is increasing or decreasing in intensity and its probable temperature, the quantity of air leakage and the explosion hazards of the fire area. The purpose of this paper is to discuss what the chemist can and cannot contribute as a member of the fire-fighting personnel. The technical literature contains several hundred papers relating directly and indirectly to mine fires, and this fact alone is testimony to the complex nature of the phenomena involved in the birth, life, and final demise of a fire. A fire may be stopped (I) by preventing oxygen from reaching the coal or (2) by removing the conditions necessary for the rapid reaction of coal with oxygen; i.e., decreasing the temperature. All methods of prevention or control necessarily must be based upon one or the other, or both, of these two principles. The chemistry of a fire may be understood readily if the low-temperature oxidation of coal is considered as a starting point; then oxidation at higher temperatures (or combustion); and with these, the composition of the solid and gaseous products resulting from the oxidation or from the effects of the heat liberated. This discussion refers particularly to Pennsylvania anthracite, although much of the material applies equally well to coals of lower rank. Oxidation of Coal Oxidation of coal fundamentally is confined to the surface; that is, the rate at which oxygen penetrates into the interior of a solid block of coal is so slow that it may be ignored."16 Oxidation starts when a fresh surface is exposed, and the rate is

Jan 1, 1942