Search Documents

The officers and staff of the Petroleum Division are the servants of the members, and to the extent that the wishes of the members are made known and are practicable they will be carried out. The tentative plans outlined here are in general accord with previous custom, but modified by suggestions received recently from various members. The advice of all members is solicited, and it is hoped that the general expression on matters of policy can soon be facilitated by circulation of a questionnaire. Plans for two mid-year meetings of the Petroleum Division and for participation in the annual meeting at New York were inaugurated at the last annual meeting and are being carried forward as rapidly as possible in the belief that an early start will increase the possibility of finding the best available program material and permit the careful preparation, review, editing, and advance discussion of papers. While a number of papers have already been solicited, both members and nonmembers are hereby invited to submit additional papers, with the assurance that such papers will be given just as favorable consideration as the papers that have been requested. Mid-year meetings will be held at about the same time both in the Mid-Continent and California. The time will be selected if possible to coincide with the visits of President Lovejoy, who expects to be in California the last of September and in Texas early in October. Fort Worth, Dallas and Austin have been suggested for the Mid-Continent meeting. The Pacific Coast meeting will be held at Los Angeles. It is to be noted particularly that a Pacific Coast meeting was waived last year in favor of the annual meeting of the American Petroleum Institute, which was held at Los Angeles for the first time in nine years. It is hoped, and it was the understanding at the time among a number of individuals interested in both organizations, that in view of this action of the Petroleum Division the industry will give more than the usual support to the A.I.M.E. meeting this year. Ultimate Recovery is being considered as the keynote topic for the mid-year meetings. In view of trying financial conditions combined with an exceptionally high current potential rate of production, it is natural that the attention of the industry should be focused upon means of controlling production and reducing cost of operation. It seems that the Petroleum Division of the A.I.M.E., as a professional group, might

Jan 1, 1936

By R. S. Shoemaker, F. W. McQuiston

REFINERY SECURITY "Highgrading, " a polite word for stealing gold and silver, has been a way of life since the metals in native form have been mined or produced. Unfortunately, in the past, highgraders were not always severely prosecuted or even looked upon unfavorably in their communities. Recent high metal prices with attendent world wide publicity, however, has made highgrading or thievery again a serious problem in mines and plants. When a small button of gold the size of the end of ones little finger has a value equal to about one week's wages, the safe-guarding of gold production by enforcing tight security measures becomes a prime responsibility of management. The higher the gold price, coupled with unrestricted owner- ship, the greater the temptation to “get-your-cut”, and diligence by management must become an integral part of plant security. Primary security begins by knowing the expected gold production and the sampling of a gold ore mill feed for this determination has proved not reliable. However, solution flows can be accurately sampled and measured thereby closely predicting the gold recovered each day as precipitate. The progressive record of total ounces of gold contained in the precipitation press, referred to in cyanidation plants as I1solution calll1 predicts the accumulated production. The "callH is an important adjunct to security and extreme caution must be used so that the pregnant solution meter and sample are confined in a security area. It should be recognized that this key sample may be the target for Ifdoctoring" by trusted insiders (assay office employees) as a preliminary step for stealing precipitates and/or metal. Security measures similar to the following were adopted after one operation experienced a sizeable theft of gold precipitate and metal by trusted employees. The refinery area where precipitates are handled and melted to bullion and all other gold products are kept should be completely enclosed with a tight security fence preferably of solid construction. Access to this enclosure should be through one of two electrically controlled gates, one for personnel and another for occasional truck entrance. Admittance should be restricted to essential personnel who are required to sign a register in and out with the date and time. I£ there is a "back gate" to the restricted fenced area, it should remain locked except in an emergency and then opened only by a supervisor. Television monitoring cameras viewing the gate entrance and other sensitive areas connected to a viewing screen located in the general office afford visual observation at all times.

Jan 1, 1975

The officers and staff of the Petroleum Division are the servants of the members, and to the extent that the wishes of the members are made known and are practicable they will be carried out. The tentative plans outlined here are in general accord with previous custom, but modified by suggestions received recently from various members. The advice of all members is solicited, and it is hoped that the general expression on matters of policy can soon be facilitated by circulation of a questionnaire. Plans for two mid-year meetings of the Petroleum Division and for participation in the annual meeting at New York were inaugurated at the last annual meeting and are being carried forward as rapidly as possible in the belief that an early start will increase the possibility of finding the best available program material and permit the careful preparation, review, editing, and advance discussion of papers. While a number of papers have already been solicited, both members and nonmembers are hereby invited to submit additional papers, with the assurance that such papers will be given just as favorable consideration as the papers that have been requested. Mid-year meetings will be held at about the same time both in the Mid-Continent and California. The time will be selected if possible to coincide with the visits of President Lovejoy, who expects to be in California the last of September and in Texas early in October. Fort Worth, Dallas and Austin have been suggested for the Mid-Continent meeting. The Pacific Coast meeting will be held at Los Angeles. It is to be noted particularly that a Pacific Coast meeting was waived last year in favor of the annual meeting of the American Petroleum Institute, which was held at Los Angeles for the first time in nine years. It is hoped, and it was the understanding at the time among a number of individuals interested in both organizations, that in view of this action of the Petroleum Division the industry will give more than the usual support to the A.I.M.E. meeting this year. Ultimate Recovery is being considered as the keynote topic for the mid-year meetings. In view of trying financial conditions combined with an exceptionally high current potential rate of production, it is natural that the attention of the industry should be focused upon means of controlling production and reducing cost of operation. It seems that the Petroleum Division of the A.I.M.E., as a professional group, might

Jan 1, 1936

SMALL things are customarily moulded in two ways (unless they have undercut parts which hold them in the moulds); that is in clay, or with natural or which artificial earthern powder made in halves in either wooden boxes or bronze frames. This also depends on whether the object is larger or smaller. Now if you wish to mould with moist clay, you must grease your relief with oil or pig fat; apply a dusting of charcoal, ashes, or cuttlebone on it; or gild or silver it dry with gold, silver, or tin foil. Then, first make with moist and somewhat firm clay a plate as, thick and large as can conveniently hold your relief, and carefully set the latter halfway into this and let it dry. Then, greasing or dusting it again, make the other half. When both are well dried, take out your relief and at the top make its gates and vents. If plastering is needed, do it. Finally, bake the halves, fit them together, and tie them well, as you wish, using the procedure that I taught you in the discussion of brass. But if one has to make a large quantity of works of one kind, he should for the sake of convenience use the method with powder [120] because it is short and requires less time and expense. Therefore if you wish to do this, you need to have several pairs of bronze frames or wooden boxes, higher than half the relief that you wish to mould, and of convenient length. On a flat board always keep half of one of these frames full of powder that has been slightly moistened for moulding, as I told you, so that by pressing with the ends of the fingers and with the hand it holds together as well as possible. Level it off with a cutting tool and when leveled put a flat board over it and turn it over. Turn it on to a dusting of ashes so that it will not stick, dust it on the other side, and remove the excess by blowing it off Then mould the thing that you wish to mould, pressing it halfway in once or twice, always taking it out and putting it back again. Then the other frame is fitted in its place and filled with earth by pressing and squeezing it carefully. Then it is leveled off on the outside with a sharp tool as you did with the other part, and then one of the parts of the frames is lifted up with the point of a knife or some other tool and,

Jan 1, 1942

By C. E. Birchenall

DaVIES and Richardson1 have measured composition changes for Mn1-Owith variation in the equilibrium partial pressure of oxygen at 1500°, 1575°, and 1650°C, where 6 is the deviation from the simple stoichiometric ratio. No trend in this relationship with temperature was observed, so these remarks apply to the whole temperature range. The experimental values and their spread are shown by the bounded straight-line segments in the figure. Davies and Richardson assume that the stoichiometric oxide shows Frenkel disorder, given by the equation Mn2+Mn2+ + Mn" [1] where Mn2+ is a normal lattice ion which moves into an interstitial site (Mni2+) leaving a vacancy (Mn,"). The superscript dashes indicate that there is an excess charge on the anions surrounding the vacancy. Schottky disorder, in which a perfect crystal acquires equal numbers of cation and anion (Ov") vacancies according to leads to equations of exactly the same form in the analysis below. In view of the neutron diffraction results of Roth,2 which shows extensive Frenkel disorder in Fe1-o, Eq. [I] seems more appropriate. The deviations from stoichiometric composition, MnO, result from the addition of oxygen according to In effect Davies and Richardson ignore the variation of Mn3+in constructing equilibrium constants. This approximation might not appear to be very serious if the excess positive charges are really free posi- tive holes (P+) and if the intrinsic conductivity is high as a result of the reaction where e- is a conducting electron. However, the calculations of Buessem and Butler3 indicate that the partition functions of the free charges make a large contribution to the equilibrium constant, and this approximation would not be a desirable one. Furthermore, Morin4 shows that the positive holes are probably localized in MnO and therefore are described better by the mass action principle than by a degenerate gas model. Davies and Richardson's considerations require that activity corrections be applied beyond a 6 value of about 0.005. It is proposed to show here that the dissociation pressure curve can be calculated reasonably well over the whole composition range studied without activity corrections by choosing appropriate equilibrium constants for reactions 1 and 2. As stoichiometric composition The mass action constant, Ks, for reaction [I.] and the equilibrium constant, K,, for reaction [2] are given by where the concentrations which do not change significantly have been absorbed into the constants. The brackets denote concentrations. The deviation from stoichometric composition is given by gardless of [Mni2 ]. Substituting Eq. [7] in [6]

Jan 1, 1961

By Nathan C. Rockwood

The title of this paper, I understand, was suggested by professional mining engineers as an opportunity for someone to pose problems rather than to offer solutions for them, but the paper will merely attempt to pose some of the production problems of the mineral aggregates industry in such manner as to create professional interest in their solution by the mining engineer, geologist, geochemist and the metallurgical engineer versed in mineral-dressing technique. Definition of Mineral Aggregates " Mineral aggregates" may be defined as fragments of any rock or mineral used to supply bulk or volume or substance for a given purpose. For example, mineral aggregates are used in portland-cement concrete to provide bulk with the expenditure of the least feasible amount of cement binder. Mineral aggregates are used without port-land cement or bituminous binder in highway and railway roadbeds to provide substance, to carry loads. provide aggregates are used in filters for water and sewage, to provide substance for the liquid to trickle through. These are only a few typical uses of mineral aggregates. For all these uses, strength, toughness, resistance to abrasion, and durability are usually prime requisites; so, while theeretically mineral aggregates may be of any mineral composition, what really is desired is a mineral composition as nearly inert under the conditions of use as anything of earthly origin can be. Exploration and Possibilities of Development The distribution of deposits of mineral aggregate is universal, since almost any part of the earth,s crust can be used; even the top soil is sometimes used in stabilized surfacing for highways or airport runways. Nevertheless there is ample opportunity for exercise of the talents of the mining engineer and the geologist in finding the particular deposit that will be most economical to develop, keeping in mind such considerations as: (i) quality and mineralogical characteristics of the material; (2) size and permanency of the market; (3) final cost of opening and development of the deposit; (4) selection of location of plant; (5) methods and costs of distribution of the product in comparison with both present and possible future competition; (6) selection of the proper type of operating equipment; (7) estimation of probable waste products and their disposal. These are typical but there are other considerations also. Because profit margins are far smaller than in any comparable mining operation, it is all the more logical to assume that a higher degree of expert knowledge is desirable to make a success of a mineral-aggregates business. The industry has much engilleering talent in its operating branch, but it lacks, to a considerable degree, engineering talent with experience

Jan 1, 1948

By Nathan C. Rockwood

The title of this paper, I understand, was suggested by professional mining engineers as an opportunity for someone to pose problems rather than to offer solutions for them, but the paper will merely attempt to pose some of the production problems of the mineral aggregates industry in such manner as to create professional interest in their solution by the mining engineer, geologist, geochemist and the metallurgical engineer versed in mineral-dressing technique. Definition of Mineral Aggregates " Mineral aggregates" may be defined as fragments of any rock or mineral used to supply bulk or volume or substance for a given purpose. For example, mineral aggregates are used in portland-cement concrete to provide bulk with the expenditure of the least feasible amount of cement binder. Mineral aggregates are used without port-land cement or bituminous binder in highway and railway roadbeds to provide substance, to carry loads. provide aggregates are used in filters for water and sewage, to provide substance for the liquid to trickle through. These are only a few typical uses of mineral aggregates. For all these uses, strength, toughness, resistance to abrasion, and durability are usually prime requisites; so, while theeretically mineral aggregates may be of any mineral composition, what really is desired is a mineral composition as nearly inert under the conditions of use as anything of earthly origin can be. Exploration and Possibilities of Development The distribution of deposits of mineral aggregate is universal, since almost any part of the earth,s crust can be used; even the top soil is sometimes used in stabilized surfacing for highways or airport runways. Nevertheless there is ample opportunity for exercise of the talents of the mining engineer and the geologist in finding the particular deposit that will be most economical to develop, keeping in mind such considerations as: (i) quality and mineralogical characteristics of the material; (2) size and permanency of the market; (3) final cost of opening and development of the deposit; (4) selection of location of plant; (5) methods and costs of distribution of the product in comparison with both present and possible future competition; (6) selection of the proper type of operating equipment; (7) estimation of probable waste products and their disposal. These are typical but there are other considerations also. Because profit margins are far smaller than in any comparable mining operation, it is all the more logical to assume that a higher degree of expert knowledge is desirable to make a success of a mineral-aggregates business. The industry has much engilleering talent in its operating branch, but it lacks, to a considerable degree, engineering talent with experience

Jan 1, 1948

By Ralph Hultgren, Bernard York, David W. Mitchell

It is a well-known fact that magnesium-alloy castings are apt to be coarse grained if the melt is not superheated several hundred degrees above the melting point before casting. (The casting temperature varies according to the shape of the mold. A typical casting temperature is perhaps 1400°F.) British practice is to heat to 900°C. (1650°F.) for 15 min., cool rapidly to casting temperature, and cast.' In Germany superheating is carried out at 850' to 900°C. (1560° to I650°F.) depending on the amount of scrap used. It is stated that further refinement will be obtained by prolonging the period of superheating or by increasing the superheat temperature to 950°C. (I740°F.).2 In the United States superheating is carried out at 1600' to 1700°F. (871' to 927°C.), perhaps even higher in some places. It is stated that superheating effects are found as low as 1500°F. (816°C.), but several hours are required.3 These commercial treatments lead to grain sizes in sand castings that may vary from 4 to 8 grains per sq. mm.! in heavy sections and from 60 to IOO in 1/2-in. sections to perhaps 380 in thin sections. It is also generally known that the refining effect of superheating is lost if the melt is held for some time at lower temperatures before casting. Aside from these very qualitative statements, there is little to be found in the literature as to the effect of temperature and time of superheat on the final grain size. Because of the uncertainty of these factors, the Office of Production Research and Development of the War Production Board placed a research contract with the University of California, supervised by the War Metallurgy Committee. This research, which was done under the "Restricted" Project NRC-550, is the basis of this paper, which has been released for publication by the O.P.R.D. The material studied was an alloy prepared from carbothermic magnesium. The temperatures required for grain refinement proved to be widely different from those used in practice, as described in the statements in the first paragraph. This difference is attributed to the fact that the magnesium in the specimens was of carbothermic origin instead of the electrolytic magnesium in common use. Materials and Methods The magnesium alloy studied was one of the most popular sand-casting alloys, with a nominal composition of 9 Per cent aluminum, 2 per cent zinc, and 0.1 per cent (minimum) manganese and the balance magnesium. This is designated

Jan 1, 1945

By John Randall

It is a fair assumption that the main purpose of any diagram is to present facts to the eye in more convenient form than they could be tabulated in figures, and this implies that a screen diagram should set forth in a convenient and familiar form certain facts as to the character of the material screened regardless of the screen standards used, and it seems particularly desirable on account of the well-known differences in the size of openings of different laboratory screens having the same nominal mesh. In making screen-sizing tests it has been customary first to consider the largest size, going progressively to the smallest, and this seems to have led to the practice of placing the smallest size .at the right-hand side of the diagram and measuring toward the left. This is not altogether convenient and might be changed to advantage, but for illustration I have preserved that feature and present the method just as I have used it for over 2 years. Direct plotting in which the intervals on the diagram are proportional to the sizes of the openings, or to the arithmetical difference between them, seems at first sight more natural and is extremely useful for certain purposes, but it makes the diagram very crowded in the smaller screen sizes while the larger ones occupy unnecessary space, making it less convenient for most purposes, and for that reason the method here discussed is the well-known one based on the ratio between openings, and is plotted in logarithms instead of the direct values of the screen opening. Metric coordinate paper is convenient, although not necessary; it is recommended, as the use of the metric scale gives a diagram of convenient size, but any scale of equal parts may be used. In order to make any screen diagram translatable in terms of any standard screen size, it is necessary to have noted on the size scale of the diagram all points corresponding to the openings of the various screens in question, instead of a single series of points as with a single screen. In drawing the diagram assume 0.001 in. (corresponding approximately to 0.025 mm.) to be the smallest size to be considered and fix this as the zero point at the lower right-hand corner of the diagram. This value is selected because the values are to be plotted in logarithms, and the logarithm of 1 is zero. Then lay off to the left for the position of each screen

Jan 1, 1918

By J. H. Frye, R. M. Treco

One of the chief hindrances to an understanding of the hardness of solid solutions is the sparsity of suitable hardness data. There is great need of a large body of hardness data obtained from many different alloys of high purity by identical testing methods and corrected to correspond to a single grain size. A considerable amount of such data has been obtained by means of the Meyer analysis on copper-rich and silver-rich solid solutions. There are enough of these data to permit comparison of numerous alloys at equal solute concentration in these two solvents, but only in a few cases is it possible to construct hardness-concentration curves for any given alloy. Therefore additional hardness work on most of these alloys is desirable. The primary solid solutions of silver with cadmium, indium, tin, or antimony as solute are of special interest, since all elements are from the same period of the periodic table and since, as shown previously,l the hardening effect of equal percentages of these solutes is proportional to the lattice expansion produced by them. This paper presents the relation between hardness and concentration in the silver-antimony system from very dilute to nearly saturated solutions of antimony in silver. Experimental Procedure Alloys were made from silver, 99.99 per cent pure, and antimony, 99.975 per cent pure. Silver and antimony were placed in graphite crucibles that had an ash content of less than 0.7 5 per cent. These metals were melted and allowed to solidify in a vacuum, which, after melting was corn- . plete, was usually equivalent to 3 mm. of mercury. A high-frequency furnace was used. The ingots so obtained were worked and annealed to lessen segregation and to control grain size. Annealing was done in evacuated and sealed glass tubes. Hardness measuremeuts on specimens from these ingots were by means of the Meyer analysis.394 Using a 4-mm. ball, impressions were made under seven loads from 25 to 400 kg. The diameter of impression made under each load was measured. This enabled calculation of the constants in the well-known formula of Meyer. L = adn where L = load, d = diameter of impression, a = a constant, n = a constant The Meyer hardness is defined as P = L/i(1/4pd2) or P = 4adn-2/p Meyer hardnesses corresponding to d = I and to d = 4 are of especial interest, since the first corresponds to comparatively slight 'plastic deformation and the second to the maximum plastic deformation producible by penetration of the ball. These

Jan 1, 1945

By D. A. Woodford

A number of observations have now been reported where the steady-state creep rate is apparently linearly dependent on the applied stress at high temperature and low stresses. This results in a creep rate greater than that predicted by extrapolation of high-stress data and has obvious practical implications. However, some of these observations are open to question. For example, the analysis by Harris and Partridge17 of the data of Greenfield et a1.18 was dependent on strain rates which, according to the original authors, were too low to be measured. Dr. Bernstein appears to have demonstrated a linear stress dependence at low stresses in two zirconium alloys. There are, however, a number of discrepancies in his treatment of the data and the subsequent theoretical analysis which require clarification. 1) It is incorrectly stated that steady-state conditions are revealed by a slope of unity on a plot of log i vs log (time). This objection is trivial if the author meant to say a slope of zero, although it is unclear how subsequent extrapolation was made to determine the steady-state creep rates at low stresses for the zircaloy-2. If the plot used was actually log c vs log (time), it is unlikely that a slope of unity would represent a constant creep rate. A plot of log (c - co) vs log (time), where c0 is the extrapolated intercept sf the steady-state creep rate on the strain axis, would have a slope of unity during steady-state creep. However, eo cannot be determined unless is is already known. 2) The author chooses to interpret his results based on the equation: where A, and B, are structure-sensitive parameters, Ql and Q, are the activation energies for the particular creep process, and n describes the sensitivity of the creep rate on stress. The first term represents a slip creep process and the second a diffusion creep process. However, it is stated later that "two distinct processes acting in parallel are involved". Eq. [I] surely represents two processes in series since each reacts to the total applied stress and t, is the sum of the individual creep rates. If the processes are acting in parallel, then the effective stress in each would be less than the applied stress. The component stresses would be given by sl + s2 = a but it is not clear how the magnitude of either, or the corresponding stress exponent, could be determined.

Jan 1, 1969

By Louis Ware

BEFORE the war we often heard the term "Big Business." And there were complaints of the ills and abuses attributed to bigness in business. Although there were examples where the small businessmen spoke for their rights and sought protection from the bigger ones, it has only been in recent war years that a tendency has developed definitely to divide the business of our nation into the big and the small. In some cases, those with an eye to the political value of the vastly greater number of small businessmen of the country have fomented this division by hurrying to the protection of these more numerous voters, and intentionally or not have emphasized in their writings and verbal attacks any and all differences of these interests that could either be found or fabricated to, suit the occasion. It has become another example of breaking the people into classes and thus setting up the basis for the claims of one class against another, and the subsequent demand for legislation and Governmental aid. The terms "big" and "small" are purely relative. One businessman, employing a hundred men, told me recently he did not know which adjective would be more appropriately applied to his operation. He did not know whether he should join the small operators' group that had been organized, or should consider himself big. He said that his present plant seemed big to him when he looked back to its humble beginning many years ago with a couple of men in two rooms. Yet, when compared with many of his competitors who employ thousands, his was small. He did add, however, that he probably became big one day a few years ago when the union moved in and organized his employees.

Jan 1, 1945

By AIME

WE produce Charles Van Ormer "Charlie" Millikan as living proof that man need not make a loud noise to be heard. His quietly affable, analytical, and soft-spoken manner in the face of all problems belies his ability to "get tough" when the situation demands it. As a chief engineer with many responsibilities for the success of a large producing company there must have been many occasions to tempt Charlie to excitement, but there are few, if any, who can say they saw him yield. He has an abiding faith in the benefits of hard and persistent work and will not admit the existence of a problem that cannot be reduced by it.

Jan 1, 1948

By Zay Jeffries

From the title of this chapter the reader could expect an attempt to out- line the anticipated shape of things to come, mineralwise. We have no crystal ball and if we possessed one we could claim no expertness in its use. In the first place no one can tell the future status of man. No one has any way of knowing to what extent peace will prevail, nor to what extent changes may occur in national sovereignties or forms of government or in international relationships. So future man is an uncertainty. Nor can we predict new developments that may result in significant changes in man's status or in the mineral industry or both. If, for example, this chapter had been written in the middle 1930's, nearly everything that has happened since in the fields of atomic energy and space technology would have been missed. Yet what vast changes these I have made in the status of man! Also the changes in the mineral industry have been important. A writer would have been bold indeed had he prophesied that uranium would play such an important role. But we need not confine our foggy vision to these fields. The steep rise in the use of aluminum, titanium, and germanium reflects the unpredictable in what may be thought of as the more normal pursuits. This should not discourage one from using the past and currently observable trends as bases for limited predictions. To do this, however, it is desirable to make certain assumptions about man's status without pretense that these assumptions have a high probability of fulfillment: 1. Only minor changes will occur in the geographical boundaries of the nations of the world. 2. World War III will not take place in the near future. 3. As a consequence of (2), man will not destroy himself by wanton use of atomic weapons. 4. Disarmament will take place, if at all, gradually rather than all at one time. Under the above assumptions the world will enjoy a period of relative peace even though the status may be one of an armed truce. The assump-

Jan 1, 1964

By Albert C. Harding

FOR several years barite (BaSO4) production has topped such better known minerals as feldspar and fluorspar in annual tonnage and is now well established among our foremost nonmetallic industries. DESCRIPTION Of widespread occurrence in the United States, barite is relatively soft (hardness, 2.5 to 3.5), inert, heavy (specific gravity, 4.5), and is also called "barytes" (sometimes pronounced "bear-i-tease"), "heavy spar" and "tiff." It occurs with granular and earthy structure but usually has coarse, orthorhombic crystallization. It is commonly white, and although occurring in various shades of red, yellow, and gray, barite always gives a white streak and can be scratched by the ordinary prospecting pick. Its softness and weight are usually sufficient to establish field identification. Another aid is the "rotten egg" odor of H2S which sometimes emanates from freshly fractured surfaces. Barite can be readily distinguished from two other minerals which have somewhat similar occurrences and characteristics. The relatively rare celestite, strontium sulphate, has a specific gravity slightly less than 4.00 and gives a distinctively crimson color in a flame test. The very rare witherite, barium carbonate, has a specific gravity of 4.3 but readily effervesces with dilute hydrochloric acid. OCCURRENCE All known commercially important barite deposits in the United States occur as re placements or cavity fillings in schists, shales, limestones, dolomites, and quartzites, or as residual deposits from such formations. In Georgia, Tennessee, North Carolina, and Missouri, high-grade barite is recovered as fragments from residual clays covering quartzites and dolomites. In Arkansas, Nevada, and California, barite, usually of lower grade, is mined from replacement deposits. These seven states contributed the entire production reported by the U. S. Bureau of Mines for 1945 as given in Table I. [TABLE 1-Crude Barite Sold or Used by Producers in 1945 STATE SHORT TONS Arkansas260,660 Missouri225,467 Georgia110,393 Tennessee32,812 Nevada28,919 Other States37,811 Total 696,062] "Other States" included only California and North Carolina. Such a large part of this undistributed production came from California that that state probably outranked both Nevada and Tennessee. For the second consecutive year Arkansas was the leading producing state, particularly worthy of note because there was no commercial production of barite there prior to 1941 and because the entire production of Arkansas has come from one large deposit which is being operated by two companies. CONSUMPTION [The 1945 consumption as reported by the Bureau of Mines was: 482,442 tons as ground barite 139,288 tons in making lithopone 99,173 tons in producing barium -- chemicals Total 720,903 tons]

Jan 1, 1947

By Enid C. Plante

INTRODUCTION To extend our knowledge of the flotation behavior of sulphide minerals, the response of the following minerals to ethyl xanthate as collector was studied by captive bubble and cylinder flotation tests: antimonite (Sb2S3), arsenopyrite (FeAsS), covellite (CuS), marcasite (FeS2), orpiment (As2S3), pyrrhotite (FeS) and tetrahedrite (4CU2S, Sb2S3). Lollingite (FeAs2) was also examined to determine if its behavior could be correlated with that of pyrite or marcasite (FeS2). EXPERIMENTAL METHOD Mineral for Flotation and Contact Tests Mineral was prepared in the manner already described' and its behavior both freshly ground and "oxidized" was studied. Tests in which the mineral was allowed to oxidize for various periods showed that a uniform response to xanthate was reached in two days or less. Oxidation Products The soluble oxidation products from most of the above minerals were measured and their effect on the flotation of the mineral studied. The mineral samples were wet ground to minus-52 mesh and deslimed, and 20 g of this material placed in 200 ml of distilled water of a measured pH value, and C02 free air bubbled through each suspension at a constant rate (about 1 bubble/sec) for 5 days. It has been shown1 that the size of the mineral is unimportant in the rate of formation of oxidation products and that probably the supply of oxygen to the mineral is the rate-determining step. At the end of 5 days the pH value of the supernatant liquid was measured again, the mineral filtered off and the soluble products determined. Methods for estimation of sulphur acids, ferrous and ferric iron and copper have already been described.1 No satisfactory method was found for antimony. Arsenic was estimated as the arsenate.2 FLOTATION OF "UNOXIDIZED" MINERALS WITH ETHYL XANTHATE AS COLLECTOR Fig I to 3, 4, 6, show the effect of alkali and cyanide as depressants for the minerals with 25 mg potassium ethyl xanthate per liter as collector at 35°C. Wark and Cox3 have shown that with ethyl xanthate as collector, galena, pyrite and chalcopyrite show a greater tolerance to cyanide and hydroxyl ions at room temperature than at 35°C. Covellite (Fig I), marcasite (Fig 2) and pyrrhotite (Fig 3) behave similarly. The independence of the curves for pyrrhotite at 35°C with respect to cyanide

Jan 1, 1947

By Richard A. Walker, John P. Hager

The thermodynamic properties of the Pb-Au system have been determined between 750" and 1075°C by means of the cell Mo, Pb(1) |(PbO-SiO2){l) , SiO2(s) |Pb-Au(1), Mo The activities of lead and gold exhibit negative deviations from ideal behavior; the values of ? pb and ? the raoultain activity coefficients at infinite dilution, being 0.24 and 0.25, respectively, at 1200°K. The liquidus curve for the gold-rich region of the Pb-Au phase diagram has been determined from measure-ments on seven alloy compositions in the two phase region (liquid + Au(s)). The standard free energies of formation of Au2O(l) and Ag2O (1) have been estimated from cell measurements obtained by replacing the alloy electrode with pure liquid gold and silver. A new integral molar heat of mixing curve for the liquid Pb-Au system is presented and the results of previous studies discussed. The contribution of HM to FE was found to be small relative to TSE. THE use of galvanic cells of the type A(l) |A+Za|A - B(l) [I] provides an accurate means for the thermodynamic study of liquid alloy systems. In Part 1&apos; it was shown that cells of type [I] may be extended to higher temperatures and to a wider range of alloy systems if the ion A+Za is incorporated in an appropriate molten oxide phase, rather than in the classical fused salt electrolyte. In the following investigation the experimental method is extended to an investigation of the thermo-dynamic properties of the Pb-Au system by use of the cell: Mo, Pb(l) | (PbO-SiO2)(l), SiO2(S) |Pb-Au(l), Mo [] Previous measurements on liquid Pb-Au alloys were obtained by Kleppa2 by electromotive force measurements on a galvanic cell involving a molten chloride electrolyte. These measurements were confined to temperatures less than 830°C and compositions with X Pb > 0.2 because of the instability of the cell at higher temperatures. Later measurements by Kleppa3 on the heats of formation in the composition range 0.67 < Xpb < 0.98 were not consistent with the results by electromotive force measurement. The purpose of the present study is to extend the temperature and composition range of the thermodynamic properties and to obtain an independent measure of the integral molar heat of mixing over the entire composition range.

Jan 1, 1970

By Carl F. Cline, Richard R. Vandervoort, Willis L. Barmore

THE objective of this investigation was to determine the high-temperature plastic deformation behavior of stoichiometric uranium mononitride as a function of stress and temperature. Interest in the properties of this material stems from its potential use in high-temperature nuclear reactor systems. The creep of other refractory compounds containing uranium (e.g., U02, UC) has been studied by various investigators.1"4 Fassler et al.4 have studied the creep of UN in vacuum from 1100° to 1350°C at stresses of 6000 and 8000 psi. In the present work, the creep of stoichiometric UN was investigated from 1500° to 1800°C at stresses from 2000 to 5000 psi in a partial pressure of 200 mm of nitrogen. The specimens were prepared by hot isostatic pressing of UN powder into cylinders of $ in. diam by about 1 in. high. After pressing, the specimens were heat-treated in nitrogen at 1900°C for 50 hr. The densities of individual specimens were determined by the water displacement method. All specimens were theoretically dense, based on a value of 14.32 g per cu cm.5 Principal metallic impurities in ppm by weight were: Ca, 50; Cu, 5; Fe, 30; Mg, 5; Ni, 10; and Si, 20. Oxygen content was 400 ± 50 pprn and carbon content was 100 i25 ppm. The nitrogen content was 5.56 ±0.05 wt pct. The average grain size for five specimens, as determined by the intercept method, was 0.14 i 0.01 mm. One specimen had a grain size of 2.0 mm. This large grain size is an anomaly, since all specimens had the same chemical and thermal histories. Specimens of 1/4 in. diam by 1/2 in. high were creep-tested in compression in a clam shell furnace heated by W-25 pct Re sheet elements. Temperature was measured to ilODC by an optical pyrometer which had been calibrated by a standard source. The distance between fiducial marks on the specimen was measured before placement into the furnace. The furnace chamber was evacuated to 10-5 Torr and back-filled to 200 mm N2. After heating rapidly to temperature, the load was applied and controlled to ±2 pct by an Instron testing machine. Upon initial loading, the specimen was deformed until a constant crosshead rate was obtained, then quenched to room temperature, remeasured, and replaced in the furnace. Upon subsequent reloading at temperature, the crosshead rate was constant for the selected condition indicating steady-state creep.

Jan 1, 1969

By A. L. Holley

THERE is a growing demand for pure and cheap material for fine open-hearth steel ; a material not only very free from phosphorus, but from carbon and silicon; so that it may he rapidly converted into steel. Iron and steel scrap are not trustworthy as to quality, and they are often dear. There are three methods of purifying cheap materials for the open hearth. 1. Mechanical puddling, as done at Creusot, which removes 90&apos; per cent. of the phosphorus from the pig iron. 2. Krupp&apos;s washing process (the conduct and results of which I fully described in a former paper*), which eliminates 70 to 80 per cent. of the phosphorus and most of the sulphur and silicon from pig iron. Neither of these processes would sufficiently purify, for very fine steel, those very impure pigs which are cheapest in many parts of the United States: 3. The process of producing directly from the ore an iron which is practically pure chemically, although mechanically mixed with the impurities of the ore. This is the oldest of iron processes ; one form of it, the Catalan forge, employed to produce charcoal blooms, is still in use, but its great cost is rapidly throwing it out of competition. Among the modern attempts to produce iron direct from the one, on a large scale and at a cheap rate, several have been in various respects successful. Dr. Siemens&apos;s process of treating a ton and a half or more of ore and the coal to deoxidize it, in a rotating gas furnace, and bringing out, in some four hours, a ball of chemically pure iron so soft that the fluid and impure slag may be squeezed out of it, is the most attractive and the most highly developed of all the modern direct processes. I have watched it, from time to time, since 1874, and have noted a steady improvement. It may now be said to have passed the experimental stage, although, like older processes, it must be adapted by practice to special materials. The cause which has been more potent than all others, including the defects of the best direct processes, to bring these processes into disrepute, is the waste-ful treatment of the direct product. With one or two exceptions (when failure was due to other and obvious causes), the direct product has been made into wrought iron (weld iron). Even Dr. Siemens has, at Towcester, in England, and at Park, Bro. & Co.&apos;s, in Pittsburg, set up his apparatus for this purpose. Is it likely that

Jan 1, 1880

By R. H. Wightman

THE following paper describes current mining practices of the Riverside Cement Co. at its Crestmore plant, Riverside, California. For a number of years the Riverside Cement Co. obtained its raw materials by surface quarry operations but after these deposits were exhausted for equipment available at that time, the company started underground mining. Mine workings were begun in 1927 to 1930 for the recovery of limestone by block-caving methods. GEOLOGY The bed of limestone that is being worked is a metamorphosed and recrystallized limestone, which is generally white in color and from medium to coarsely crystalline. This bed is fissured by water courses that vary from minute cracks to large areas. The bed has also been cracked by intrusions along the footwall and hanging wall. These walls are coarse-grained, gray, quartz granodiorite. The strike of the deposit is north and south and it dips to the east at an angle of approximately 50º. The bed is approximately 1700 ft. long, 270 ft. thick at right angles to the dip at the middle of the deposit and tapers to a thickness of approximately 100 ft. at each end. MINING METHODS The mine layout consists of four main levels with elevations as follows: 892 Collar of shaft. 800 Manway level used for ventilation, prospect purposes and as an entrance into the stopes. 700 Mining level where all material is extracted and on which are located the tapping grizzlies. This is the elevation from which all main cutoff stopes and undercutting work is started. 660 Haulage level where the limestone is drawn from transfer raises into the cars and is transported to the tipple by electric locomotives. 633 Level where all water is collected and which keeps the general water table below the working levels. A detailed description of the mine was given in U. S. Bureau of Mines Information Circular No. 6795, in June 1934. Current Block Development The first blocks to be caved were developed very much after the procedure followed in the copper mines of Arizona. This paper covers the ninth block to be caved. With a hard, tough rock like our limestone, it was found that some alterations in the development and control of draw in caving were necessary to secure better crushing effect and provide more safety for such secondary blasting as is required. Sequence of Block Development I. The fringes of the 800-ft. manway level are driven to confirm the diamond drill information and serve to determine the final location and development required for the block (Fig. I).

Jan 1, 1944