Search Documents

By Walter Stern

THE self-potential or spontaneous polarization method is one of the oldest in the field of electrical exploration. When applied in prospecting for ore bodies, it is one of the most rapid and inexpensive means of locating indications of ore bodies at shallow depth. Usually, the procedure is to survey the equipotential lines of the electrical field that is generated by the electrochemical activity of the ore near the ground-water level, and to localize the so-called negative centers or points of greatest negative anomaly. Another field procedure involves the measurement of potential differences along potential profiles, generally laid out at right angles to the assumed strike. Again, in such survey, the basis for establishing the presence of ore is the location of negative potential anomalies. The earlier writers on the subject, notably Schlumberger1 and R. G. Wells,2 did much to clarify the fundamental electrochemical phenomena involved. Interpretation of the field data, however, remained largely qualitative. In 1925, A. Petrovsky3 analyzed the relation between the shape of the potential anomaly curve and size and depth of an ore body by assuming the subsurface body to be a polarized sphere.4 Along similar lines of approach, Edge and Laby5 considered the ore body a dipping sheet with limited extent in the direction of strike, while Poldini6 based the theory on the assumption of a dipping bar. The following study endeavors to enlarge [ ] FIG. I.-ORE BODY CONSIDERED AS DIPOLE upon these earlier investigations and attempts, on the basis of the potential distribution of a polarized bar, to indicate certain characteristics of the anomaly curve that make possible the determination of depth, size and dip of a subsurface body. THE SPONTANEOUS POLARIZATION FIELD SET UP BY AN ORE BODY If a sulphide ore body is subjected to oxidation varying in degree in its upper and lower parts according to the difference in the concentration of oxygen within the surrounding medium, an electrical potential field is set up. The form and distribution of this field will be investigated herein with special reference to its components on the earth's surface. Under the simplifying assumption that the ore body may be considered as a dipole with the point sources QI and Q2 situated at its upper and lower ends (Fig. I), the potential of the spontaneous polarization at point P is given by the following equation:

Jan 1, 1944

By J. P. Nielsen

When two grains in a polycrystalline specimen meet at a point in the course of grain-boundary movements, and the new boundary created at the point is one of relatively low specific free energy, a nonequilibrium boundary condition occurs. The nonequilibrium is enhanced if the other grain boundaries involved at the point of meeting are relatively high in specific free energy. The nonequilibrium results in a correction by growth of the complex grain (two subgrains) to a large size, sufficient in many cases for it to become a self-propagating unit, i.e., a recrystallization grain. This mechanism, herein called "geometrical coalescence," is proposed as a logical origin for recrystallization nuclei, particularly for secondary recrystallization. RECENT publications1-' indicate that considerable progress has been made toward a complete understanding of the three microstructural processes in metals: recovery, recrystallization, and grain growth. However, a major problem persists, namely, the origin of recrystallization nuclei. It is generally accepted that once a recrystallization nucleus, a secondary recrystallization nucleus particularly, has reached a certain size, it will continue to grow at the expense of its neighbors, simply as a consequence of grain-boundary free-energy considerations. What has remained obscure, however, is the mechanism whereby such a nucleus comes into being and grows to the self-propagating size. Recrystallization Nucleation in a Two-Dimensional Grain-Boundary System In the left portion of Fig. 1 is shown schematically the meeting of grains 1 and 4 on disappearance of boundary 2-3, i.e., the boundary that existed between grains 2 and 3, as might happen in the course of normal grain-boundary migration. If, by chance —and the probability is not necessarily small— grains 1 and 4 are close together in their mutual orientations, or in some other special way mutually oriented so that the new common boundary has relatively a very low specific free energy (hereinafter referred to by s), then the grain boundary arrangement as depicted in the figure is highly unstable. This is particularly so if boundaries 1-3, 3-4, 4-2, and 2-1 are high in their s values. Assuming, for the sake of argument, that boundary 1-4 has a s equal to zero, and the s's of all the other boundaries present are equal to each other and constant, then the boundary arrangement on the right in Fig. 1 will be

Jan 1, 1955

By H. Rush Spedden

Antoine M. Gaudin was a vigorously creative man and throughout his career an internationally respected leader of his chosen profession of mineral engineering. To his professional colleagues and clients and to his former students he was both "Professor Gaudin," their wise, inspiring, and enthusiastic teacher, and "Tony," their, warm and beloved personal friend. Thus, his teachings and his unique inquisitive-creative approach to problems live on and grow in the accomplishments of his students. Antoine Gaudin was born at the turn of the century in Smyrna, Turkey, where his father was general manager of a French-owned railroad. It was there that he spent his earliest years, literally in the shadow of classic marbles from diggings at the site of Aphrodesias, which his father had rediscovered. From this, Tony developed an appreciation of the arts. He eventually surrounded himself with art treasures; he reveled in the beauties of nature, and he cherished his choice collection of rhododendron and azaleas. His artistic traits led him to take up painting when his daughter, Elinor, sought his help in blending her tints for a water color. In typical fashion he was not satisfied until he had become adept with pastels in capturing the muted tones of distant landscapes and the technical properties of light and color. Unfortunately not many paintings were produced. His paternal grandfather was Marc-Antoine Gaudin, for many years secretary of the Academie des Sciences in Paris, and a well known chemist and mineralogist whose primary interests included the synthesis of precious stones. In an autobiographical sketch written in 1939, Dr. Gaudin recalled: "As a child I saw many of the original synthetic sapphires and rubies which my father had inherited. This, coupled with my father's avocation of mining ventures and archaeology, early decided that I would become connected with the mineral industry." One can speculate that the archeological activities of his father, the mineral systhesis experiments of his grandfather, and his own early studies of mineralogy and geology formed a base from which his special talents as an experimentalist were to develop. Laboratory research under Professor Gaudin's personal guidance was often an intensive, fast-moving, and exciting experience--especially to a new graduate student. First of all, Professor Gaudin was a highly skilled observer with seem-

Jan 1, 1976

By W. S. Ayres

By James S. Baker

LARGER than continental United States but with only about one third the population, Brazil is a land of enormous potential wealth, waiting to be developed. During a recent visit to that country I saw Brazil at war and learned about some of the recent mineral developments. Many engineers and geologists have been sent to Brazil by various U. S. Government agencies to assist the Brazilian producers and co-operate with the Brazilian Government in producing needed war minerals. The Foreign Economic Administration staff of engineers has been active and through their assistance to the Brazilian producers, steadily increasing quantities of strategic minerals were provided to aid the United Nations' war effort. Mineral wealth has been found in almost every state of Brazil. Many mineral deposits have been discovered during the war period. Examples are: barite near Bahia; the tungsten and molybdenum deposits in Rio Grande do Norte; and corundum, beryl, and tungsten ores in Ceara.

Jan 1, 1945

By William G. Christy

EFFORTS at smoke abatement date back to the year 1273 in England when a law was passed prohibiting the use of "sea cole." The law was not enforced, so King Edward I, 33 years later, appointed a commission "to enquire of all such who burnt sea cole in the city or parts adjoining, and to punish them for first offense with great fines and ransomes, and for the second offense to demolish their furnaces." Many other commissions have since been named to investigate the smoke problem in England, but it still persists in many British cities. In the United States the movement to abate the smoke nuisance started in certain Middle Western cities, and has made considerable progress. Until recently, the coal-producing industry co-operated little in smoke¬abatement programs, taking the attitude that smoke elimination is the dealer's or user's responsibility; and the dealers, in turn placed the responsibility entirely on the user.

Jan 1, 1942

By F. O. Garrabrant

Power is furnished to the Climax Molybdenum Co. by the Public Service Co. of Colorado over two 100,000-volt lines to a bank of three 3333-kva. transformers 100/13.8 kv. These transformers are so designed that with the addition of forced cooling their capacity may be increased 331/3 Per cent at 12,000-ft. altitude. Under present conditions, these transformers are operated at 140 per cent of their rating with forced air cooling. On the secondary side of this bank there is a 15-kv., 1200-amp. Westinghouse oil circuit breaker provided with automatic reclosing relays allowing three successive short circuits before lockout. From this breaker 13.8-kv. power is transmitted to a central switching station (Fig. I) where all circuits radiate to the different operations of the property. Each circuit is protected by a 23-kv., 600-amp. oil circuit breaker with by-pass and isolating disconnecting switches.

Jan 1, 1947

By R. E. Crockett

MAGNETITE mining and milling in the Eastern States was at capacity during 1940, owing to the heavy industrial, defense, and war demand, coupled temporarily with the almost total stoppage of imports of foreign ores other than those under American ownership. In New York State the active mines were those operated by the Republic Steel Corp. at Mineville and Lyon Mountain. Republic's new concentrating mill at Port Henry, handling the Mineville ores, went into production about the first of April. Other large magnetite deposits in New York are currently being prospected and studied and may be under development in the near future. In New Jersey the Mt. Hope and

Jan 1, 1941

By Frank Firmstone

Discussion of the paper of John B. Dilworth, presented at the Pittsburg meeting, March, 1910, and printed in Bulletin No. 35, November, 1909, pp. 1041 to 1043. FRANK FIRMSTONE, Easton, Pa. (communication to the Secretary*) :-Mr. Dilworth's formulas and tables are of course correct, and the extinction will occur as calculated, provided the money periodically set aside for sinking-fund be really invested. and the interest compounded as assumed in the calculation. Actually, in almost all cases, such funds are used "in the business," in which case, in addition to the periodical charges for principal of the fund, additional charges must be made at the end of each period to cover the interest and compound interest on previous charges. The periodical charge for sinking-fund thus becomes a varying and continually increasing one until the date of extinction. On many accounts it seems more natural and convenient to make the extinction by a fixed periodical charge under the legal rule for partial payments, namely, that each payment should apply first to the interest due at the date of payment;: and any remainder, after this is satisfied, be deducted from the principal before the interest for the next period is calculated. The formula below is convenient for such calculations S, Principal to be extinguished. Q, Periodical payment or charge for sinking-fund. B, Balance unpaid at date of nth payment, but before that payment is made. r, Rate of interest per period per cent. n, Number of payments or periods. Then, B=S(1+r)n-Q(1+ r)n-(1+r) Received July 27, 1910.

Apr 1, 1911

By Thomas V. Falkie, Robert Stefanko

Recently The Wall Street Journal featured a series of articles titled "The Dirty Work-Brutal, Mindless Labor Remains a Daily Reality for Millions in The US.-Mining Coal, Shoveling Slag, Gutting Hogs Pays Bills But Can Drain Spirit, Hope." The article was devoted to describing how tough and dangerous is mining (and some other jobs) and how rough life is for miners and their families. Similarly during the past few years some psychiatrists and sociologists have devoted increased attention to the attitudes and life styles of miners. Unfortunately most of their approaches have been neither scientific nor objective, and very little good clinical research has been done on the subject.

Jan 1, 1971

Edward A. UehliNg, New York City (communication to the Secretary*):—In adding my mite to the discussion, I wish to touch on a few points which bear emphasizing and perhaps a little further elucidation. Mr. Grammer says that he "found the electric pig-breaker at Duquesne, if used in connection with the iron-chill, less expensive and more satisfactory " thau the casting-machine. The cost of handling the iron over the Duquesne casting-niachine is about double the average cost of the other Uehling machines at the several Carnegie plants. It is nearly as expensive to run as the Hey1 & Patterson machines, and while Mr. Grammer's statement is, no doubt, true, as applied to that particular machine and breaker, it should be borne in mind that the machine at Duquesne had embodied in it several new features, which were not improvements; also that it was taxed beyond its economic capacity. The machine at the Lucy furnaces under the management of Mr. Scott handled the output of the two furnaces, and saved

Jan 1, 1905

By William B. Plank

RECENT interest in the character of employment of young mining engineering graduates has been stimulated by my studies, during the past ten years, of student enrollment and employment of graduates of the mineral technology schools of the United States and Canada. Enrollment data in the following article are taken from these studies and information about the kind of work engaged in by mining engineers is assembled from my professional experience, sixteen years of which have been as professor of mining engineering.

Jan 1, 1938

By C. A. Zapffe

BOTH the foundryman and the theoretical metallurgist are now generally agreed that the anomalous "rising" or "bleeding" of certain ferrous castings of killed metal is primarily attributable to hydrogen. How and why the phenomenon occurs, however, have not been made clear. The following discussion is intended to harmonize foundry experience with metallurgical theory so that the foundryman may possibly improve his ability to prognosticate whether a certain casting may bleed or not. BLEEDING, RISING, AND PIPING The "rising" to be discussed here is not to be confused with the action in rimming ingots as a result of the carbon-oxygen reaction, although a conclusion will be drawn that may apply to the art of controlling the rimming action. Only killed metal is considered, which includes both steels and irons. In Fig. I, three killed, chill-cast ingots are shown: a porous ingot whose evolution of gas during late stages of solidification has ejected metal through the top; an ingot in which moderate gas evolution during solidification has lifted the mushy central metal, i.e., it has "risen"; and, third, a sound ingot with good piping characteristics. The first type is referred to as "bleeding," and generally infers that a solid skin had first formed through which the liquid metal later erupted. There is no fundamental distinction between bleeding and rising in reference to killed metal.* POROSITY Hydrogen appears as a cause of bleeding because the gas evolution simultaneously leaves a porosity of a type traceable to hydrogen. Twenty years ago, Melmoth1 noted that killed steel that rose unexpectedly in the mold, if returned while liquid to the furnace and heated further under a reducing lime slag, would again rise in the mold; but that if the ingot were allowed to solidify and was then remelted no rising occurred. A critical quantity of the responsible gas is therefore removed by the rising action. Melmoth associated rising with high silicon (0.7 to 0.9 per cent) and concluded that silicon increased gas absorption. Because silicon is a strong deoxidizer, oxygen must, therefore, be eliminated from consideration of the three common gases in steel-oxygen, nitrogen, and hydrogen. Butterworth2 later decided that pinhole porosity was caused by gases dissolved in the metal and that hydrogen was obtained from steam in the mold. Allen's classical work on copper castings,3 soon followed by

Jan 1, 1942

By Edward N. Trump

Extensive beds of rock salt occur in New York, Michigan, Kansas, and Texas. Wells are drilled through the beds, cased, and equipped with a suspended center tube. By circulating water through such a well, the soluble saline is dissolved and a brine produced. Operation of a well results ordinarily in the formation of an inverted conical cavity in the saline, inasmuch as the dissolving action of the fresh water is more rapid at the top of the bed than at the bottom. Under continued operations, the side wall of the cavity becomes so flat that a blanket of mud is deposited thereon and if the bed is overlain with shale or a soft rock caving follows. Three methods of operating wells have been employed—the "Tully plan," "the Detroit plan," and "the Trump plan." Both the Tully plan and the Detroit plan involve the formation of the aforesaid conical cavity with constant caving of shale above and deposition of mud on the side wall; the Trump plan was developed to avoid both these circumstances and thus materially prolong the life of a well. Details of the three plans follow. The Tully Plan In the Tully plan, the water passes down the annular space between the casing and the center tube, the brine rising in the center tube (Figs. I and 2). An inverted conical cavity is formed, the side wall of which relatively soon becomes so flat that it is blanketed by mud and impurities from the rock salt; this blanket limits dissolving action to the perimeter of the base of the cone, situated at the top of the saline bed. Caving of the overlying strata follows, and the total production of brine from the well is comparatively small. The Detroit Plan In the Detroit plan, the water passes down the center tube, the brine rising in the annular space between the center tube and casing (Figs. I and 2). Initially, this flow forms a pear-shaped cavity in the bottom of the salt bed, but this cavity soon changes in shape to that of an inverted cone, as under the Tully plan, with the attendant disadvantages inherent in that plan. Application of the Detroit plan is limited to salt beds 300 ft. thick as a minimum. This depth of bed is necessary to prevent fresh water of lower specific gravity than the brine from rising in the

Jan 1, 1948

By Edward N. Trump

Extensive beds of rock salt occur in New York, Michigan, Kansas, and Texas. Wells are drilled through the beds, cased, and equipped with a suspended center tube. By circulating water through such a well, the soluble saline is dissolved and a brine produced. Operation of a well results ordinarily in the formation of an inverted conical cavity in the saline, inasmuch as the dissolving action of the fresh water is more rapid at the top of the bed than at the bottom. Under continued operations, the side wall of the cavity becomes so flat that a blanket of mud is deposited thereon and if the bed is overlain with shale or a soft rock caving follows. Three methods of operating wells have been employed—the "Tully plan," "the Detroit plan," and "the Trump plan." Both the Tully plan and the Detroit plan involve the formation of the aforesaid conical cavity with constant caving of shale above and deposition of mud on the side wall; the Trump plan was developed to avoid both these circumstances and thus materially prolong the life of a well. Details of the three plans follow. The Tully Plan In the Tully plan, the water passes down the annular space between the casing and the center tube, the brine rising in the center tube (Figs. I and 2). An inverted conical cavity is formed, the side wall of which relatively soon becomes so flat that it is blanketed by mud and impurities from the rock salt; this blanket limits dissolving action to the perimeter of the base of the cone, situated at the top of the saline bed. Caving of the overlying strata follows, and the total production of brine from the well is comparatively small. The Detroit Plan In the Detroit plan, the water passes down the center tube, the brine rising in the annular space between the center tube and casing (Figs. I and 2). Initially, this flow forms a pear-shaped cavity in the bottom of the salt bed, but this cavity soon changes in shape to that of an inverted cone, as under the Tully plan, with the attendant disadvantages inherent in that plan. Application of the Detroit plan is limited to salt beds 300 ft. thick as a minimum. This depth of bed is necessary to prevent fresh water of lower specific gravity than the brine from rising in the

Jan 1, 1948

As we understand the functions of the A. I. M. E. Petroleum Division, they are to discover and promote knowledge for the benefit of society on the mining of oil and gas. To the individual member of the Petroleum Division, there are certain advantages of social and professional contacts, but the collective purpose is that described. And the individual is benefited by membership only as the Division measures up to the purposes of its existence. Consequently, the welfare of this Division and that of its members depends upon the extent to which it keeps pace with the needs of society on matters relating to the mining of oil and gas. To some extent, A. I. M. E. activities must be determined by the changing current needs of society. The great problem ahead of the world for some time is to evolve equitable types of production control in many industries, and especially is that true of the oil industry. Production control in this industry is as much an engineering function as is production development, notwithstanding it also involves the lawyer, the economist and the politician. It must be built on and around suitable engineering planning enforced by public opinion and legislation. We believe the prerequisite to any satisfactory solution of the oil industry's ills is an educational campaign establishing a better public understanding of the needs and merits of production control, by which we mean the maximum yield at the minimum cost coordinated to society's current needs. The underlying causes of the oil industry's ills are well known and generally agreed upon. In like manner there is general agreement among students of the industry that the first step toward their correction would be general adoption of oil-field developing and operating methods that would permit most efficient use of reservoir energy; that would provide for equitable distribution of oil and gas among the several owners in the pool; and also for the extraction of these products in response to market demand. It is now found, however, that general adoption of such developing and operating methods unfortunately cannot be brought about without changes being secured in certain basic laws of oil and gas, and perhaps also in the anti-trust laws. These legal changes are difficult to secure because of the widespread fear that they would tend to place the oil industry more exclusively in the hands of the major companies, and that

Jan 1, 1932

By Edward N. Trump

EXTENSIVE beds of rock salt occur in New York, Michigan, Kansas, and Texas. Wells are drilled through the beds, cased, and equipped with a suspended center tube. By circulating water through such a well, the soluble saline is dissolved and a brine produced. Operation of a well results ordinarily in the formation of an inverted conical cavity in the saline, inasmuch as the dissolving action of the fresh water is more rapid at the top of the bed than at the bottom. Under continued operations, the side wall of the cavity becomes so flat that a blanket of mud is deposited thereon and if the bed is overlain with shale or a soft rock caving follows. Three methods of operating wells have been employed-the "Tully plan," "the Detroit plan," and "the Trump plan." Both the Tully plan and the Detroit plan involve the formation of the aforesaid conical cavity with constant caving of shale above and deposition of mud on the side wall; the Trump plan was developed to avoid both these circumstances and thus materially prolong the life of a well. Details of the three plans follow. THE TULLY PLAN In the Tully plan, the water passes down the annular space between the casing and the center -tube, the brine rising in the center tube (Figs. I and 2). An inverted conical cavity is formed, the side wall of which relatively soon becomes so flat that it is blanketed by mud and impurities from the rock salt; this blanket limits dissolving action to the perimeter of the base of the cone, situated at the top of the saline bed. Caving of the overlying strata follows, and the total production of brine from the well is comparatively small. THE DETROIT PLAN In the Detroit plan, the water passes down the center tube, the brine rising in the annular space between the center tube and casing (Figs. I and 2). Initially, this flow forms a pear-shaped cavity in the bottom of the salt bed, but this cavity soon changes in shape to that of an inverted cone, as under the Tully plan, with the attendant disadvantages inherent in that plan. Application of the Detroit plan is limited to salt beds 300 ft. thick as a minimum. This depth of bed is necessary to prevent fresh water of lower specific gravity than the brine from rising in the

Jan 1, 1944

The ventilation of metal mines is becoming more of a fundamental requirement than it was 10 or even 5 years ago. There are many reasons for this, and in general they are based on economy or efficiency rather than health or safety, yet the latter enters into the picture in at least some instances. One Montana metal mine which had installed mine fans and a general ventilating system shut down the fan when there was a period of cessation of work; within a few weeks it was found that the underground timbers were becoming so covered with fungus that the fans were put into operation and thereafter continued in operation whether the mine was worked or not. The fungus soon disappeared and the cost of operating the fans was held to be far less than would be the numerous losses from timber decay which quickly started when cessation of air flow was encountered. A large iron ore mine in Michigan had much difficulty in holding men in a slicing region due to foul air under certain surface conditions as to direction of wind. Upon the placing of a moderate sized fan on the surface with some doors, stoppings and regulators underground, not only was the bad air condition removed but there was found to be a decided increase of tonnage per man per shift and timber decay was retarded to a very considerable extent. This particular mining company was rather inclined to be angry when I called attention to some of the what I considered very bad working conditions underground, and the mine superintendent for about a year and a half was on anything but friendly terms with me. Later on when the effect of the placing of the fan was found (the fan had been placed over his protest), that, man came through very nicely with a letter and congratulated me on the recommendation made and congratulated himself and the company on the conditions obtained after the installation of the fan. Poisonous Fumes after Blasting A copper mine in the Southwest with an ore of a high sulfide content has much difficulty due to poisonous fumes after blasting, and the, fan installation is as elaborate as those of many of the most nearly up-to-date coal mines, and coal mine splitting and regulating practices are being

Jan 1, 1927

By Ralph Hultgren, Louis A. Carapella

When F. Heuslerl found in 1898 that certain alloys containing only copper, manganese, and tin were ferromagnetic, the discovery excited a great deal of interest and led to numerous investigations. It was early found that tin could be replaced by aluminum, arsenic, antimony, bismuth, or boron without destroying the ferromagnetic nature of the alloys.2 Copper may also be replaced by silver.% All these alloys have come to be known as "Heusler alloys." The aluminum alloys apparently were the most magnetic and have been most extensively investigated. However, no agreement has yet been reached as to the source of the ferromagnetism arising from these nonferromagnetic elements. Absence of reliable quantitative data makes speculation hazardous. The value of much of the earlier work was vitiated by lack of necessary precautions against contamination, and by lack of close control of heat-treatment. It was only recently established that in aluminum Heusler alloys4 the ferromagnetism arose from a single phase, an ordered body-centered-cubic structure. With modern methods of preparation, heat-treatment, and X-ray examination, it is possible to prepare these alloys without contamination, to heat-treat them intellgently, and to determine what phase or phases are present in the finished sample. In the present investigation, a series of pure alloys in the comparatively neglected copper-manganese-tin system have been prepared, which consist of a single, body-centered-cubic structure (the beta phase) and whose compositions vary within wide limits. The magnetic saturation values of these single-phase alloys have been quantitatively determined, so that considerable data on the effect of composition on the ferromagnetism have been made available. In the course of the investigation some information on the extent of the stability of the beta phase and the nature of phases in adjacent regions of the ternary diagram has been accumulated. Anomalies in earlier data. have been explained, and alloys have been prepared that are much more strongly magnetic than any previous Heusler alloys. Previous Work In the original work of F. Heuslerl and coworkers,2 a maximum magnetic saturation value of I = 107 was found at the composition Cu6Mn3Sn, while a value for CusMnAl of I = 443 was early measured. Ross and Gray5 found a second maximum at the composition Cu2MnSn, which was much more magnetic than Heusler's original alloy. F. Heusler6 hen reinvesti-gated the system, confirmed their results,

Jan 1, 1942

By Louis A. Carapella, Ralph Hultgren

When F. Heuslerl found in 1898 that certain alloys containing only copper, manganese, and tin were ferromagnetic, the discovery excited a great deal of interest and led to numerous investigations. It was early found that tin could be replaced by aluminum, arsenic, antimony, bismuth, or boron without destroying the ferromagnetic nature of the alloys.2 Copper may also be replaced by silver.% All these alloys have come to be known as "Heusler alloys." The aluminum alloys apparently were the most magnetic and have been most extensively investigated. However, no agreement has yet been reached as to the source of the ferromagnetism arising from these nonferromagnetic elements. Absence of reliable quantitative data makes speculation hazardous. The value of much of the earlier work was vitiated by lack of necessary precautions against contamination, and by lack of close control of heat-treatment. It was only recently established that in aluminum Heusler alloys4 the ferromagnetism arose from a single phase, an ordered body-centered-cubic structure. With modern methods of preparation, heat-treatment, and X-ray examination, it is possible to prepare these alloys without contamination, to heat-treat them intellgently, and to determine what phase or phases are present in the finished sample. In the present investigation, a series of pure alloys in the comparatively neglected copper-manganese-tin system have been prepared, which consist of a single, body-centered-cubic structure (the beta phase) and whose compositions vary within wide limits. The magnetic saturation values of these single-phase alloys have been quantitatively determined, so that considerable data on the effect of composition on the ferromagnetism have been made available. In the course of the investigation some information on the extent of the stability of the beta phase and the nature of phases in adjacent regions of the ternary diagram has been accumulated. Anomalies in earlier data. have been explained, and alloys have been prepared that are much more strongly magnetic than any previous Heusler alloys. Previous Work In the original work of F. Heuslerl and coworkers,2 a maximum magnetic saturation value of I = 107 was found at the composition Cu6Mn3Sn, while a value for CusMnAl of I = 443 was early measured. Ross and Gray5 found a second maximum at the composition Cu2MnSn, which was much more magnetic than Heusler's original alloy. F. Heusler6 hen reinvesti-gated the system, confirmed their results,

Jan 1, 1942