Search Documents

By Maynard H. Jameson

EARLIER investigations of the potential-drop-ratio method of electrical prospecting have indicated that under suitable conditions this method is well adapted to the location of formation boundaries in stratified ground. A description of this development was given several years ago by H. Lundberg and Th. Zuschlag.1 The curves published by these authors for the potential-drop-ratio variation above a horizontal contact indicated a definite relation of the position of the curve peak to the depth of the interface. The theory underlying this relation was subsequently studied by Z. Mitera in greater detail,2 and the theoretical deductions were compared with the results of tank experiments. The investigations available at this writing were confined to studies of horizontal formation boundaries. It is the purpose of this paper to extend the scope of the previous work to the problem of dipping layers. THEORY Consider the case of three media of different resistivities, whose interfaces are not parallel. If a point-source is located in one of these interfaces, its images do not lie in a straight line, but on the circumference of a circle whose center is at the hypothetical junction of the interfaces. R. F. Aldredge3 determined the relation that exists between the degrees of dip of the two interfaces and the distances between the various images and the point for which the potential is to be found. As seen in Fig. I, three media of resistivities po, pi, and p2 are involved, and the source I is located at the interface of the media (po) and (pi). The perpendicular depth of the lower interface is h,? is the dip, R is the distance between source I and potential point P, and r is the distance between the images and that point. To distinguish between images lying above the ground interface and those below, the notation "odd" and "even" images will be employed; images below the ground interface will be termed "odd" and those above "even." The following relations govern the distances between either kind of images and the potential point: [ ] As previously pointed out, the images of the source are on the circumference of a circle. If the angle of dip is ?, the angle measured from the horizontal to the first image is 2? to the second image it is 4?,, and so on. Since the limit of the reflecting interface is at its outcrop, the last possible

Jan 1, 1941

Page Foreword. By Edmund M. Wise..................... 3 A.I.M.E. Officers and Dircctors...................... 4 Institute of Metals Division Officers and Committees............ 7 Institute of Metals Division Annual Award Certificate............ 8 Institute of Metals Division Lectures and Lecturers............. 9 Photograph of E. H. Dix, Jr., Institute of Metals Division Lecturer...... 10 PAPERS Acceleration of the Rate of Corrosion by High Constant Stresses. By E. H. Dm, JR. (Institute of Metals Division Lecture, T. P. 1204).......... 11 Variation of Internal Friction with Grain Size. By Clarence Zener and R. H. Randall. (T.P. 1146, with discussion) .............41 Changes in Damping Capacity during Annealing of Alpha Brass. By John T. NoRton. (T.P. 1168, with discussion)................49 An Electron Diffraction Study of Anodic Films. By R. A. HarrinQton and H. R. Nelson. (T.P. 1158).....................62 Determination of Orientations by Etch Pits. By Charles S. Barrett .and L. H. Levenson. (T.P. 1171, with discussion).............76 Process of Precipitation from Solid Solution, I—A Crystallographic Mechanism for the Aluminum-copper Alloys. By Carl H. Samans. (T.P. 1186). . . 85 Age-hardening of Aluminum Alloys, IV — Discussion of the Theory. By WilTJam L. Fink and Dana W. Smith. (T.P. 1083, with discussion). . . 95 Structure of Aluminum after Compression. By Charles S. BaRREtt and L. H. evensonON. (T.P. 1104, with discussion)................112 Recrystallization Texture of Aluminum after Compression. By ChaRlEs S. BarRett. (T.P. 1141, with discussion)................128 Plastic Deformation and Recrystallization of Aluminum Single Crystals. By J. A. Collins and C. H. Mathewson. (T.P. 1145, with discussion) . . . 150 Recovery and Recrystailization in Long-time Annealing of 70-30 Brass. By S. E. Maddigan and A. I. Blank. . (T.P, 1166, with disonssion).....170 Correlation of Deformation and Recrystallization Textures of Rolled 70-30 Brass. By R. M. Brick. (T.P. 1144, with discussion).........193 Tensile Deformation of Critically Oriented Brass Crystals. By H. L. Burghoff. (T.P. 1149).............................214 Recrystallization of Lead. By Paul A. Beck. (T.P. 1101, with discussion). . 222 Simple Method of Thermal Analysis Permitting Quantitative Measurements of Specific and Latent Heats. By Cyril Stanley Smith. (T.P. 1100, with discussion).............................236 Metallographic Study of Internal Oxidation in the Alpha Solid Solutions of Copper. By Frederick N. Rhines. (T.P. 1162, with discussion). . . . 246

Jan 1, 1940

By K. Leutwyler

The authors present an interesting review of various applications of rather well known theories. Their rearrangement of the original working equations is strictly computer oriented and serves well to that effect; however, the new appearance will be confusing to the slide rule-wielding members of the profession. In reviewing discrepancies existing between calculations made by Baker Oil Tools, Inc. field engineering staff members and computer output submitted based on the authors' program, the following error in concept was discovered in Eq. 4. The authors quote the length change due to helical buckling in the following form We appreciate Kurt Leutwyler's awareness of Archimedes' principle, and concur that the final term in the denominator of Eq. 4 results in a small error. Examples checked revealed less than I ft error, and corrective expressions for the four possibilities of displacement follow. The portion of the denominator within extra large brackets represents the original term W,, = weight of outside fluid displaced per unit length. The authors interpreted the expression "displaced" in general oilfield terminology as a fluid displacement, such as "mud displaced with water, etc." A review of the theory forming the basis for these helical buckling calculations discloses that this displacement is meant to be interpreted in the Archimedean sense, i.e., fluid displaced by the solid body. here the tubing and the seal nipple. Lubinski* illustrated the point by summing moments due to mechanical and hydraulic forces acting on a free body immersed in fluid. This moment summation, always in the Archi,medean sense, yields effects of the real forces, including W,, and the fictitious force on the bending mechanism. I would be interested to hear the authors' comments regarding this theoretical point, which nevertheless is not mute since its lack of recognition seems to result in erroneous calculations. We must not remain mute to Leutwyler's suggestion that these equations, although computer oriented, are confusing to the slide rule engineers. Such input information as density in pounds per gallon, pipe diameters in inches, pumping rate in barrels per minute and pipe length in feet is not confusing to most of us. Yet there may be some rugged individuals in field positions who carry tables of conversion constants and have committed to memory such items as coefficients of thermal expansion and Poisson's ratio; however, even this type of individual would welcome a simplified equation occasionally. M

Page Foreword. By Edmund M. Wise..................... 3 A.I.M.E. Officers and Dircctors...................... 4 Institute of Metals Division Officers and Committees............ 7 Institute of Metals Division Annual Award Certificate............ 8 Institute of Metals Division Lectures and Lecturers............. 9 Photograph of E. H. Dix, Jr., Institute of Metals Division Lecturer...... 10 PAPERS Acceleration of the Rate of Corrosion by High Constant Stresses. By E. H. Dm, JR. (Institute of Metals Division Lecture, T. P. 1204).......... 11 Variation of Internal Friction with Grain Size. By Clarence Zener and R. H. Randall. (T.P. 1146, with discussion) .............41 Changes in Damping Capacity during Annealing of Alpha Brass. By John T. NoRton. (T.P. 1168, with discussion)................49 An Electron Diffraction Study of Anodic Films. By R. A. HarrinQton and H. R. Nelson. (T.P. 1158).....................62 Determination of Orientations by Etch Pits. By Charles S. Barrett .and L. H. Levenson. (T.P. 1171, with discussion).............76 Process of Precipitation from Solid Solution, I—A Crystallographic Mechanism for the Aluminum-copper Alloys. By Carl H. Samans. (T.P. 1186). . . 85 Age-hardening of Aluminum Alloys, IV — Discussion of the Theory. By WilTJam L. Fink and Dana W. Smith. (T.P. 1083, with discussion). . . 95 Structure of Aluminum after Compression. By Charles S. BaRREtt and L. H. evensonON. (T.P. 1104, with discussion)................112 Recrystallization Texture of Aluminum after Compression. By ChaRlEs S. BarRett. (T.P. 1141, with discussion)................128 Plastic Deformation and Recrystallization of Aluminum Single Crystals. By J. A. Collins and C. H. Mathewson. (T.P. 1145, with discussion) . . . 150 Recovery and Recrystailization in Long-time Annealing of 70-30 Brass. By S. E. Maddigan and A. I. Blank. . (T.P, 1166, with disonssion).....170 Correlation of Deformation and Recrystallization Textures of Rolled 70-30 Brass. By R. M. Brick. (T.P. 1144, with discussion).........193 Tensile Deformation of Critically Oriented Brass Crystals. By H. L. Burghoff. (T.P. 1149).............................214 Recrystallization of Lead. By Paul A. Beck. (T.P. 1101, with discussion). . 222 Simple Method of Thermal Analysis Permitting Quantitative Measurements of Specific and Latent Heats. By Cyril Stanley Smith. (T.P. 1100, with discussion).............................236 Metallographic Study of Internal Oxidation in the Alpha Solid Solutions of Copper. By Frederick N. Rhines. (T.P. 1162, with discussion). . . . 246

Jan 1, 1940

By G. F. Tagg

In an earlier paper1, the author described a method of interpreting earth-resistivity curves, based on the theoretical investigation of a single horizontal underlying stratum. If the four-electrode system of Wenner is employed, the resistivity in a homogeneous soil is given by the formula where a is the electrode separation and R is the resistance of the earth between the two inner electrodes. If the earth is not perfectly homogeneous, the application of this formula gives an apparent specific resistance varying with the electrode separation. In the special case of the single horizontal underlying stratum, there is a surface layer of thickness h and resistivity p1 and a lower layer, extending to infinity, of resistivity pz. It has been shown by Lancaster-Jones2 that the apparent resistivity obtained by an application of equation 1 is related to the true resistivities, the depth h and the electrode separation a by an expression of the formhere pa is the apparent resistivity and F is a function (actually an infinite series), of the ratio h/a, and a reflection coefficient k = (p2 — p1)/(p2 + p1). For given values of h/a and k, the right-hand side of equation 2 can be calculated, and curves drawn showing the relationship between pa/p1, h/a and k. Such a set of curves for the case when p1 > p2 is given in Fig. 1. When pl is less than pz it is more convenient to use conductivity instead of resistivity. Hence, if oa = the apparent conductivity = lip, and a1 = the conductivity of the upper layer = l/pl, it follows that GeophyGical prospecting by earth-resistivity methods is frequently applied to investigation of structural problems in geology. Fig. 1 indicates a scheme of the general arrangement used in these methods of measurements. The battery (or generator) E is connected with two "current electrodes" I1 and I2. The current of intensity J, supplied by this battery, passes through the earth between these elcc- trodes. A potential difference U will be measured between two other electrodes V1 and Vz, called "potential electrodes." According to the configuration of electrodes (Fig. I), the resistivity of a homogeneous soil results from the formula

Jan 1, 1940

By G. F. Tagg

In an earlier paper1, the author described a method of interpreting earth-resistivity curves, based on the theoretical investigation of a single horizontal underlying stratum. If the four-electrode system of Wenner is employed, the resistivity in a homogeneous soil is given by the formula where a is the electrode separation and R is the resistance of the earth between the two inner electrodes. If the earth is not perfectly homogeneous, the application of this formula gives an apparent specific resistance varying with the electrode separation. In the special case of the single horizontal underlying stratum, there is a surface layer of thickness h and resistivity p1 and a lower layer, extending to infinity, of resistivity pz. It has been shown by Lancaster-Jones2 that the apparent resistivity obtained by an application of equation 1 is related to the true resistivities, the depth h and the electrode separation a by an expression of the formhere pa is the apparent resistivity and F is a function (actually an infinite series), of the ratio h/a, and a reflection coefficient k = (p2 — p1)/(p2 + p1). For given values of h/a and k, the right-hand side of equation 2 can be calculated, and curves drawn showing the relationship between pa/p1, h/a and k. Such a set of curves for the case when p1 > p2 is given in Fig. 1. When pl is less than pz it is more convenient to use conductivity instead of resistivity. Hence, if oa = the apparent conductivity = lip, and a1 = the conductivity of the upper layer = l/pl, it follows that GeophyGical prospecting by earth-resistivity methods is frequently applied to investigation of structural problems in geology. Fig. 1 indicates a scheme of the general arrangement used in these methods of measurements. The battery (or generator) E is connected with two "current electrodes" I1 and I2. The current of intensity J, supplied by this battery, passes through the earth between these elcc- trodes. A potential difference U will be measured between two other electrodes V1 and Vz, called "potential electrodes." According to the configuration of electrodes (Fig. I), the resistivity of a homogeneous soil results from the formula

Jan 1, 1940

By D. F. Botkin, B. H. Sage, W. N. Lacey

Joule-THomson coefficients for two natural gases were determined at pressures up to 600 lb. per sq. in. throughout the temperature interval between 70" and 310°F. From these primary data and available information relating to the isobaric heat capacities of the components at infinite volume, the heat capacities of these gases were computed throughout the above-mentioned range of pressures and temperatures. The enthalpies of the gases were computed as a function of state and the results compared with values obtained by several methods of prediction currently available. Table i .—Composition of Gas Samples Components Gas A Gas B Carbon dioxide................ 0.0090a 0 .042 0 Methane...................... 0.8255 0.8385 Ethane.......................0.0901 0 .0637 Propane....................... 0.0462 0.0374 Isobutane..................... 0.0074 0.0039 n-butane................ ...... 0. 0126 0 .0095 Isopentane.................... 0.0032 0.0016 n-pentane..................... 0.0022 0.0011 Hexanes and Heavier........... 0.003& 0.0023 Experimentally determined Joule-Thom. son coefficients for natural gases afford a satisfactory means of checking the accuracy of prediction of their thermodynamic properties from the behavior of the components in the pure state and in binary mixtures. Relatively small samples of these natural gases were available, together with their analyses, and the Joule-Thomson coeffi- The Joule-Thomson coefficients were determined by measuring the change in temperature resulting from the passage of the gas through a porous thimble with a known pressure difference and under such conditions that the process was substantially isonthalpic. The details of the apparatus employed for this purpose have been described.' It is believed that the changes in temperature and pressure were ascertained with an uncertainty of not more than 0.3 per cent. However, as a result of deviations from steady flow, it is probable that uncertainties as large as 2 per cent may exist in the measured Joule-Thomson coefficient. The gases utilized in this work were taken from high-pressure separators and were dried prior to use by passage over calcium chloride at pressures in excess of 300 lb. per sq. in. The gases were subjected to the conventional fractionation and Orsat analyses. The results are recorded in Table I. The composition is typical of gases from such sources, with the possible exception of the presence of significant quantities of carbon dioxide in each of the samples. The experimental results obtained for the two natural gases are graphically Portrayed in Figs. I and 2. The experimental

Jan 1, 1943

By W. N. Lacey, D. F. Botkin, B. H. Sage

Joule-THomson coefficients for two natural gases were determined at pressures up to 600 lb. per sq. in. throughout the temperature interval between 70" and 310°F. From these primary data and available information relating to the isobaric heat capacities of the components at infinite volume, the heat capacities of these gases were computed throughout the above-mentioned range of pressures and temperatures. The enthalpies of the gases were computed as a function of state and the results compared with values obtained by several methods of prediction currently available. Table i .—Composition of Gas Samples Components Gas A Gas B Carbon dioxide................ 0.0090a 0 .042 0 Methane...................... 0.8255 0.8385 Ethane.......................0.0901 0 .0637 Propane....................... 0.0462 0.0374 Isobutane..................... 0.0074 0.0039 n-butane................ ...... 0. 0126 0 .0095 Isopentane.................... 0.0032 0.0016 n-pentane..................... 0.0022 0.0011 Hexanes and Heavier........... 0.003& 0.0023 Experimentally determined Joule-Thom. son coefficients for natural gases afford a satisfactory means of checking the accuracy of prediction of their thermodynamic properties from the behavior of the components in the pure state and in binary mixtures. Relatively small samples of these natural gases were available, together with their analyses, and the Joule-Thomson coeffi- The Joule-Thomson coefficients were determined by measuring the change in temperature resulting from the passage of the gas through a porous thimble with a known pressure difference and under such conditions that the process was substantially isonthalpic. The details of the apparatus employed for this purpose have been described.' It is believed that the changes in temperature and pressure were ascertained with an uncertainty of not more than 0.3 per cent. However, as a result of deviations from steady flow, it is probable that uncertainties as large as 2 per cent may exist in the measured Joule-Thomson coefficient. The gases utilized in this work were taken from high-pressure separators and were dried prior to use by passage over calcium chloride at pressures in excess of 300 lb. per sq. in. The gases were subjected to the conventional fractionation and Orsat analyses. The results are recorded in Table I. The composition is typical of gases from such sources, with the possible exception of the presence of significant quantities of carbon dioxide in each of the samples. The experimental results obtained for the two natural gases are graphically Portrayed in Figs. I and 2. The experimental

Jan 1, 1943

By Enid C. Plante

To extend our knowledge of the flotation behavior of sulphide minerals, the response of the following minerals to ethyl xanthate as collector was studied by captive bubble and cylinder flotation tests: antimonite (Sb2S3), arsenopyrite (FeAsS), covellite (CuS), rnarcasite (FeS2), orpiment (As&.), pyrrhotite (FeS) and tetrahedrite (4CU2S, Sb2S3). Lollingite (FeAs2) was also exarnined to determine if its behavior could be correlated with that of pyrite or rnarcasite (FeS2. Experimental Method Mineral for Flolation and Contact Tests Mineral was prepared in the manner a1ready described1 and its behavior both freshly ground and "oxidized" was studied. Tests in which the mineral was allowed to oxidize for various periods showed that a uniform response to xanthate was reached in two days or less. Oxidation Products The soluble oxidation products from most of the above minerals were measured and their effect on the flotation of the mineral studied. The mineral samples were wet ground to minus-52 mesh and deslimed, and 20 g of this material placed in 200 ml of distilled water of a measured pH value, and CO2-free air bubbled through each suspension at a constant rate (about I bubble/sec) for 5 days. It has been shown1 that the size of the mineral is unimportant in the rate of formation , oxidation products and that probably the supply of oxygen to the mineral is the rate-determining step. At the end of 5 days the pH value of the 'supernatant liquid was measured again, the mineral filtered off and the soluble products determined. Methods for estimation of sulphur acids, ferrous and ferric iron and copper have already been described.l No satisfactory method was found for antimony. Arsenic was estimated as the arsenate.2 Flotation of "Unoxidized" Minerals with Ethyl Xanthate as Collector Fig I to 3, 4. 6, show the effect of alkali and cyanide as depressants for the minerals with 25 mg potassium ethyl xanthate per liter as collector at 35°C. Wark and Cox8 have shown that with ethyl xanthate as collector, galena, pyrite and chalcopyrite show a greater tolerance to cyanide and hydroxyl ions at room temperature than at 35°C Covellite (Fig I), marcasite (Fig 2) and pyrrhotite (Fig 3) behave similarly. The independence of the curves for pyrrhotite at 35°C with respect to cyanide

Jan 1, 1949

By Edmond S. Miksch

The morphology and growth rate of ice grown in supercooled water are markedly affected by convection of the water. A dendritic ice sheet with water flowing past the dendrite tip exhibits deflection of the dendrite spine toward the upstream direction, accelerated growth of secondary spines on the upstream side, and suppression 01" secondaries on the downstream side. Flow causes a thin disk to become corrugated, the corrugations being parallel to the flow. Flow causes an increase in the growth rate of the ice. IF a small seed of ice is placed in slightly supercooled water, it grows initially as a disk with the axis of the disk parallel to the c axis of the ice crystal.' It appears that growth in the c direction is inhibited, while growth occurs with equal facility in all directions in the basal plane. It appears that growth rate as a function of interface temperature is very nearly equal for all directions similarly oriented relative to the c axis. Subsequent to the discoid growth, branching occurs and dendrites develop. The primary dendrite spines grow parallel to the six equivalent a axes of the crystal. Secondary, and in some cases, tertiary spines also grow in these directions. The highly anisotropic: dendritic growth indicates that there must be some finite difference of growth rate for different directions in the basal plane. These differences must be quite small, however, since if they were large, the discoid mode would not occur. Hence, it was expected that the dendrite growth direction could be deflected from the crystallographic direction by perturbation of the thermal field at the dendrite tip. Experiments were done in which perturbation of the thermal field was accomplished by causing the supercooled water to flow past the dendrite tip. The flow direction was perpendicular to the c axis of the crystal, and was perpendicular to the primary spine of the unperturbed crystal. Supercooled water was supplied by a 15 cm cubical copper box, which was refrigerated and insulated so it could cool water to temperatures down to —2oC, and maintain the temperature constant to O.l°C for the duration of a run. A lucite channel of rectangular cross-section, 12 by 24 mm, was mounted horizontally in the box, with one end open so water could flow into it, and the other end leading out through the wall of the box to a length of tubing leading: to an orifice plate 123 cm below. cnunMn s MIKSCH, MemberAiMe, formerly Research Associate, Research Associate, Fig. l(b)—Vertical section of apparatus A horizontal cross-section is shown in Fig. l(a), and a vertical section is shown in Fig. l(b). Means for observing the ice are shown in Fig. l(a). Collimated light passes through the ice sheet and forms an image on the ground glass screen. A lucite box containing dry air was employed to prevent condensation. Ice of the desired orientation was provided by the seed holder shown in Fig. l(b). This device was made of lucite, and had a reservoir in which ice could be frozen by placing it in a freezer. This reservoir com-unicated with the outside only through a narrow gap between two sheets of lucite. The seed holder (after ice had been washed off its exterior) was immersed in the tank of supercooled water, the narrow gap terminating in a slot in the top of the flow channel. Ice growing through a thin water layer in the gap between the two sheets of lucite was oriented so its c axis was perpendicular to the sheets. This orientation is an application of a growth phenomenon2 which causes ice growing along a smooth solid surface in supercooled water to orient itself so its c axis is normal to the surface. After the ice grew into the channel, further orientation was necessary, since the direction of the a axis

Jan 1, 1970

PHILIP D. BLOCK, JR., vice president of Inland Steel Co., visualizes a fine future for the Menominee Range of the Upper Peninsula of Michigan. He sees a future unclouded by threat from foreign ore imports or the development of low grade ore processing in Minnesota. The statement was made during the opening of Inland's new Cayia mine near Crystal Falls. Inland, according to the vice president, is planning to use an increased amount of the high phosphorous ores found on the Menominee Range. He said that other steel companies will probably do the same, because the steel industry has learned how to use ores of high phosphorous content. He said: "I do not mean to imply that we can use an unlimited amount of high phosphorous ores or that we can burden our blast, furnaces with 100 pct high phosphorous ores, but we have reached the point where we can absorb a much larger percentage of these ores without any detrimental effects. Foreign ores and lowgrade Minnesota ores cost too much to offer real competition, Block said. Transportation costs from the Menominee range to steel producing centers in Chicago and on Lake Erie are less than for any other range in this country. In the meantime, the American operators of the Bomi Hills iron ore mine in Liberia, have reportedly signed a new agreement with the Government. Several months ago, President Tubman of Liberia expressed a definite dissatisfaction with the original contract. Informants state that the agreement only needs the approval of the Export-Import Bank, which loaned Liberian Mining Co. $4 million to develop the iron ore properties. Majority stockholder of the Liberian Mining is Republic steel, with 61.57 pct of the stock. Under the new contract, the Liberian Government will start to share in the profits when the indebtedness is liquidated and the return of invested capital accomplished, or April 1, 1957, whichever is earlier. Under the old agreement the Liberian Government received a 5 cent per ton royalty and an additional sum based on the price of pig iron. The royalty rate reached more than 17 cents per ton this year. After debt liquidation the Liberian Government will receive 25 pct of net profits for the first five years; 35 pct for the next ten years; and 50 pct thereafter. Until the Government starts to share in profits it will receive a royalty of $1.50 per ton in U. S. currency, in addition to royalties provided for in the old agreement.

Jan 1, 1952

By C. A. Heiland

NOT only has the demonstration of progress in all fields of science been characteristic of the Chicago "Century of Progress," but the manner in which the fundamentals of these sciences have been displayed captivated the visitor's eye and ear at the same time. The average individual is interested most in progress which concerns his every-day life. He is fairly well educated in medicine, biology and certain aspects of physics. But how raw materials and chiefly minerals occur, how they are located, taken out of the ground and refined, is something which appears to be more remote from the every-day line of interest, and about which, therefore, the public knows comparatively little. This is particularly true of the oil industry, although it ranks in size second only to agriculture in the United States. In appreciation of the tremendous educational value which a complete exhibit on all phases of the mineral industries would have, both mining and metallurgical as well as oil inter¬ests took steps early to make these exhibits at Chicago a reality. The board of directors of the A. I. M. E. authorized an advisory committee to the Museum of Science and Industry early in 1932. It is divided into four subcommittees - for geology and petroleum, for metal mining, for coal mining, and for metallurgy respectively. The entire committee held its first meeting in Chicago on April 11 and 12, 1932, to advise with the Museum's officials and experts about the most advantageous arrangement of the minerals industries' and geology exhibits.

Jan 1, 1933

By S. E. Clay, G. P. Martins, P. R. Taylor

A grain model for gas-solid reactions in cylindrical pellets is formulated and solved numerically. The numerical solution demonstrates when it is safe to assume either a thin disk or a long cylinder geometry, and when the more general two dimensional geometry must be used. The numerical solution also demonstrates the solution of a two-dimensional moving boundary problem (i.e., when the reaction is diffusion controlled and the ratio of the height to diameter dictates two dimensions).

Jan 1, 1986

By Fred E. Carter

AT first sight, the platinum group of metals seem of little import to we, the people," although actually the life of the common man is much influenced by them; this influence is usually indirect, hence his lack of knowledge and interest. He generally associates platinum with high-class jewelry and lets it go at that. Were 11e to go deeper, he would find that platinum metals play their part in his food supply, his clothing. his health, his transportation, his home. And the technical man is in general only slightly better informed, for he usually does not realize how necessary platinum metals are in the manufacture of the many construction materials and chemical products with which he is acquainted. Certainly, our daily lives would be profoundly affected if platinum were suddenly to become unavailable.

Jan 1, 1944

By John Riegle

To date. utility company underground storage of gas has generally been restricted to depleted dry gas fields. The Playa del Rey project is probably the first to successfully store gas in a partially depleted oil reservoir with the recovery of large volumes of pas at high rates as the main objective. Oil recovery has been a secondary consideration. Problems encountered unusual to those of storage in a dry gas zone were: (1) the removal and retardation of formation of emulsion. (2) the upstructure movement of fluid during withdrawal periods which formed fluid blocks, and (3) reservoir shrinkage resulting from encroachment of edgewater. The solution of these problems as outlined in the paper has resulted in increasing the withdrawal rate from the original design capacity of 4,000 Mcf per hour to the current 10.000 Mcf per hour. Additional increase is anticipated as the operations continue. Migration. reservoir performance. operational procedure and a historical record are included to make this a resume of the project from its war-time inception in 1942 to the first of 1952. INTRODUCTION The Playa del Rey underground gas storage project is probably the first project in which gas has been stored in a partially depleted oil reservoir, with the recovery of large volumes of gas at high rates as the main objective and the recovery of oil a secondary consideration. Problems unusual to those of storage in dry gas zones have made this a pioneer endeavor. The total storage capacity of approximately 1,500,000 Mcf of this reservoir is small in comparison with other underground gas storage projects. However. by study and experiment the deliverability into transmission lines. operating at pressures in excess of 150 lbs., has been nearly tripled in the past three years. to the current 10.000 Mcf per hour late, without the use of compression. It is anticipated this rate will gradually increase as additional fluid is removed from the formation. LOCATION AND HISTORY Playa del Key is located on Santa Monica Bay about two miles south of the beach commuity of Venice and 15 miles southwest of the renter of the City city Los Angeles. Fig. 1. The discovery well was completed at 6,194 ft in 1929. An upper zone at 3,905 ft was found on June 18. 1930. Townlot development was very rapid and by the end of 1930 there were 141 producing wells in the field. The Union Oil Co. completed a lower zone well south of the Townlot Field in May, 1931, which was believed to be an extension, until additional drilling of about 50 wells during 1934 and 1935 indicated this area to be a separate accumulation as shown on Fig. 2. The lower oil horizon, which is now the storage zone, had no original gas cap and is believed to be a continental detrital deposit of conglomerate that accumulated in valleys and depressions of a weathered schist high. which later subsided and was overlain by an impervious nodular shale. This type of formation has rapid variation of porosity. permeability and thickness due to lack of sorting action common to marine deposition. and the uneven surface of the original schist high. Production was limited on the upstructure sides by the pinching out of the conglomerate, and downstructure by edgewater. Unrestricted production, together with high permeabilities, led to large wastage of gas from this new area as facilities were not available for transport of gas to market. The decline was very rapid and by 1942 the portion of the new area south of Ballona Creek was nearly depleted. ACQUISITION OF PROPERTY The rapid increase in industrialization of Southern California during World war 11 forced upon the local gas com-

Jan 1, 1953

By J. L. Bray

ACCELERATED programs, as discussed in this paper, refer to the year-around operation of a college or university with three sixteen-week or four twelve-week terms per year, with pauses between sufficient only to allow the administrative group to perform their functions. In most engineering schools, under such conditions, the conventional four-year course can be condensed to two years and eight months. These accelerated programs of study, which now exist in most of our technical institutions, were forced upon us under the influence of the outburst of wartime patriotism, perhaps one might go so far as to call it hysteria. Many of us felt and hoped that these programs were temporary expedients, but the cold hard threat of permanency now rears its head; consequently we should examine the merits and shortcomings of the new order, and evaluate its effect on our educational system, since it may persist in some form in the postwar years, because of the changing political and financial situation. Many engineering students are being educated in state supported institutions

Jan 1, 1944

"The greatest mining center in the state of Utah is the incorporated town of Bingham about twenty-five miles southwest of Salt Lake City. The principal industry of this vicinity, prior to the early fall of 1 863, was lumbering and the first saw-mill in the state was built near the mouth of Bingham Canyon. Early in the fall of that year, George B. Ogilvie discovered gold and shortly afterward the first mining district in the state was organized. Some writers place the discovery of gold in the canyon in the late fifties. If this be so, however, the matter was kept extremely quiet because no mining was engaged in until after Ogilvie's discovery.Bingham was a placer mining camp, producing about one million dollars' worth of dust and nuggets from placers up and down the canyon and in Bear Gulch until early in the seventies, or about ten years after the discovery of gold, when a large body of argentiferous lead ore was discovered and soon after heavy shipments were made from a half dozen or more properties.In 1 8 74, A. H. and George L. Bemis erected the first concentrating plant in the state for the treatment of sulphide lead ores.The history of the camp as a producer of copper begins in the summer of 1 88 7, when Enos A. Wall noticed, in observing prospecting drifts and inclines driven some years before, the discoloration caused by the coppery solution. As a large part of the adjacent ground had been abandoned, he located two claims, which he called the ""Dick Mackintosh"" and the ""Charles Reid,"" after two of his friends.Late in 1896, the Highland Boy Mine produced sulphide ore rich in copper, causing a revival of interest in the copper potentialities of the camp, and during the next seven years a number of new claims were located ."

Jan 1, 1925

By M. W. Lightner

IN 1947 the steel industry rebounded from its wartime effort and produced a record-breaking peacetime tonnage of steel ingots. During the first six months of the year the industry produced 42,000,000 tons of ingots and expected to produce 85,000,000 tons for the year. With a rated capacity of some 91,000,000 tons, production was at a rate of about 93 per cent of capacity. Credit must be extended to the steel producers who have maintained this steady state of operations while faced with many problems, not the least of which was a continued shortage of satisfactory scrap. Furthermore, the steel industry started a record-breaking peacetime expansion program at a total cost of more than $1,000,000,000. This program will increase the ingot-making capacity of the country by 2,500,000 tons and should be completed in 1948.

Jan 1, 1948

By Charles H. Moore

In the study of the properties of rutile pigments it became apparent several years ago that certain physical and optical properties could not be determined on particles of pigmentary size. Since reflected light is the dominant type which reaches the eye from small particles, the true color of pure rutile was not known. Most rutile pigments are acicular in habit, elongated parallel to the "c" axis. It was considered important to know the nature and tone of light transmitted, for example, by a basal plate. Further, as shown by spectrophotometric curves, there is a very strong absorption of light of 4000 k as measured on particles with random orientation. It would be interesting to see whether this absorption position varied with predetermined and selected orientations. Also, since the behavior of titanium pigments in a vehicle is important, a knowledge of the surface wettability of single crystals by various media should prove very fruitful. Finally, the optical properties of rutile are such that it should show, in a single pure crystal, greater fire and brilliance than the diamond. Mineralogists had long speculated that this would be the case and curiosity was strong to produce a single crystal large enough to cut.

Jan 1, 1949

C. D. Demond, Anaconda, Mont. (communication to the Secretary*) :—In order to throw some light on this interesting subject, a series of experiments were made with strips of mild steel, containing about 0.14 per cent. of C and 0.22 per cent. of Ma. These strips were thoroughly cleaned and brightened before use, salts were added to distilled water until it corresponded as nearly as possible to the analysis given by Mr. Lee, and in this water at different temperatures were placed four strips of steel; while four other strips, at corresponding temperatures, were placed in the water used at the Washoe Reduction Works. The latter plant has had no trouble from corrosion of furnace-jackets, pipe-lines or boilers. The analysis of the water used at the Washoe works is: Grains er U. S. Gallon. CaCO3........... 2.92 CaSO3........... 0.76 MgCI3........... 0.64 MgCO3........... 0.58 A1203........... 0.12 Fe2O3........... 0.12 SiO2........... 0.58 NaCl........... 0.35 Organic matter, etc.,........ 1.16 7.23 This water is neutral to litmus; while the artificial Copper Queen water was very slightly alkaline, which Mr. Lee informs us is also true of the water at Douglas. Both waters mere well aerated by pouring from beaker to beaker, and by blowing in air from the experimenter's lungs. The results of these tests, given in Table I., show that there is no significant difference between the effects of the two waters.

Jan 1, 1909