Search Documents

By W. S. Row

This mine is operated at 4000 to 4500 tons daily through a single shaft, with one rock hoist and one senice hoist. Latest shaft construction is concrete with wooden dividers. Economics of drifters and air-leg drills are compared, as well as costs of shrinkage and sub-level stoping. Economy of large haulage equipment and underground crushing is shown. THE property of Kerr-Addison Gold Mines is located in the Larder Lake district of Ontario about 3 miles from the Quebec boundary on the highway between Kirkland Lake and Noranda. It is roughly 320 miles due north of Toronto and 365 miles north of Buffalo, N. Y. The property was staked in 1906 and after several development efforts finally came into continuous production at 500 tons per day in 1937. In 1939 the daily tonnage -was increased to 1200 and in 1941 to 2100 tons. At the end of the war, because of the shortage of labor, tonnage was down to 1100 tons per day, rising to 2200 in February 1947. A further plant expansion inaugurated in 1946 was completed by December 1948, bringing the capacity of the mine and mill to a production rate of 4000 tons per day. Current production, with 880 men employed, is 4400 tons per day. Changes in mining methods and equipment, required by the recently completed expansion program, have yielded interesting comparative results, some of which are described in this paper. Hoisting of ore and waste from the mine, as well as all service facilities for handling men and supplies underground, are provided for in a single vertical five-compartment shaft. Ore and waste are hoisted in 12½-ton skips in balance by a 14-ft diam hoist with drums 115 in. wide, grooved for 2?-in. wire ropes. This hoist, with a total rope pull of 85,000 lb, was designed to operate at a speed of 2600 ft per min to a depth of 4000 ft, hoisting 15 tons of ore in each skip. It is amplidyne-controlled and powered with dual drive dc motors of 2250-hp each, through flexible couplings to two pinion shafts, one on each side of the main gear. Each motor has a peak load rating of 4500-hp at point of greatest duty. Direct current power to the hoist motors is supplied from a motor generator set consisting of a 5000-hp synchronous motor driving two 1750-kw dc generators. The loading pockets used so far are at depths of 1500 and 2725 ft respectively. Consequently the present hoisting speed is 2000 ft per min and the skips capacity only 12½ tons. Now that the shaft has been deepened the new pockets at 3934 ft will be increasingly used so that the speed and the skip size will be increased up to original specifications as required. Some difficulty in meeting the required hoisting cycle is expected because of the shape of the skips. As now in use the cross-sectional dimensions of the inside of the skip are 4 ft 6 in. x 3 ft 8 in. To hold 121/2 tons, therefore, they are 14 ft 10 in. deep. Since the skips are the conventional overturning or Kim-berley type, considerable hoisting time is lost in retardation in entering the headframe dump and in acceleration when leaving. It is expected that to obtain the specified tonnage from this hoist when the skip size is increased to 15 tons it may be necessary to resort to bottom dump skips. This type of skip could reduce considerably the present excessive acceleration and retardation times. Analyses of the skip-hoisting operation are made monthly, and every effort is made to reduce controllable delays. For a nine-month period in 1951 such an analysis shows that the hoist was in operation 92.5 pct of the available time, which was allotted as shown in Table I. Overall hoisting costs, cage and skip, for the year 1951, averaged $0.168 per ton of ore milled. The mine is serviced entirely by means of a single cage, capacity 35 men or 15,700 lb, operating in con-

Jan 1, 1954

By George A. Guess

THE increasing demand for greater speed and more accuracy, in making daily assays of ores and products from mills treating material containing but very small quantities of lead and copper, has caused the older analytical methods to be supplanted by new ones devised to meet the needs of modern work. For " control " work in copper analyses, I had, previous to the present equipment, introduced in my laboratory the ordinary electrolytic method, using hollow cylindrical electrodes, and with these I began a series of experiments in determining the lead-content of daily mill-samples and controls. The results, proving accurate and satisfactory, I then devised, with Mr. H. E. T. Haultain, a cheaper electrode than the ordinary jacket electrode, which costs from $15 to $20,-the expense of the older form making the installation of many units very costly. The form of cathode finally adopted as the most satisfactory, shown in Fig. 1, is cut from 0.001-in. platinum foil. It is 12.5 cm. long, and is divided into a blade 4 cm. wide and 6.25 cm. long, and a tongue 0.7 cm. wide and 6.25 long, the immersion area being 50 sq. cm. and weight 1.5 grams. The blade is first sand-blasted and then corrugated lengthwise, in order to impart the necessary rigidity. Strips of platinum foil 0.001 in. thick, 12.5 cm. long and 0.5 cm. wide, having a median corrugation, form the anodes. Three electrodes are used in each cell, one anode in the middle and one cathode oil each side of the anode. These electrodes are connected to slotted alumi¬num terminals, in which they are held by contact pressure. The terminals are -in. rods, projecting 2 in. horizontally in front of the wall of the cabinet.; at the back the middle electrode (anode) is connected with one pole of the current, and the two outer ones (cathodes) with the other pole.

Nov 1, 1905

By G. Osuch, G. Derge, G. M. Pound

Using a new dternating-current potentiometer circuit and a specially designed four-terminal cell, the specific conductance of molten Cu2S-FeS mattes was measured as a function of temperature, from the liquidus to 1500°C, over the complete range of composition. The high conductivities, about 1500 ohm-I cm-l for FeS and 100 ohm-l cm-l for Cu,S, indicate that the conduction is electronic rather than ionic. Molten FeS has a negative temperature coefficient of specific conductance, resembling metallic conduction. Molten Cu,S has a positive temperature coefficient, resembling semiconduction. The binary roughly follows an additive rule of mixtures with respect to both magnitude and temperature coefficient of specific conductance. Metallic bonding in the liquid is postulated to explain these phenomena. MUCH has been learned in the past about the nature of liquids and the ionic or molecular species in solution by means of electrical measurements. Thus, dielectric constants','2 have given information about molecular liquids such as water and benzene. Measurements of dielectric constant usually are impossible in electrically conducting liquids, such as aqueous solutions of ionic salts and molten ionic salts. However, measurements of electrical conductance and ionic transference have provided much knowledge about the latter systems.a-" In recent years, the ionic nature of certain molten metallurgical slags has been established by Derge and Martin7 through electrical conductance and electrolysis measurements. Chipman, Inouye, and Tom-linsonq ave studied the electrical conductance of molten FeO and report a high specific conductance of about 200 ohm-' cm-' (compared with 4 ohm" cm-' for an ordinary ionic liquid such as molten NaCl) and a positive temperature coefficient of conductance. They interpret these results in terms of p-type semiconduction by analogy to the situation in solid FeO.Y imnad and Derge" have studied cell efficiency in the electrolysis of molten FeO-SiO, systems and conclude that ordinary ionic conductance increases with SiO, content. Very recently, interest has been revived in the electrical conductance of liquid metals and liquid metallic solutions. Scala and Robertson1' report a close resemblance between the liquid and solid states with respect to thermal, structural, and compositional relationships. Molten sulphides have not received a great deal of attention. Bornemann and von Rauschenplat" measured the specific conductance of molten Cu2S as a function of temperature with a four-terminal cell using direct current. A high specific conductance and a positive temperature coefficient were found in that investigation." Using a two-electrode apparatus, Savelsberg" electrolyzed various molten sulphide mixtures. He concluded that pure molten Cu,S and FeS were electronic conductors but that the mixtures exhibited some ionic conduction. In the present investigation, the specific conductance of the industrially important Cu-Fe sulphide mattes was measured as a function of temperature and composition in order to investigate the mode of electrical conduction and the structure of these molten mattes. An alternating-current circuit was used to eliminate the effect of any possible electrode reactions. Apparatus The Conductance Cell: Due to the high specific conductance of the systems studied (10' to 10" ohm-' cm-'), the classical two-terminal cell and Wheat-stone bridge apparatus could not be used. A four-terminal cell was developed in order to eliminate lead resistance, and an ac potentiometer circuit was designed to give rapid and sufficiently accurate measurements of the cell resistance. A diagram of the conductivity cell is given in Fig. 1. The molten matte is contained in a dense alundum crucible, and spectrographic graphite rods that dip into the molten matte serve as the four conductance terminals. Two of the graphite rods on opposite sides of the cell serve as current-carrying leads, and the other two graphite rods are null-current probes that detect the potential drop across the cell. These graphite rods are contained in silica tubes, and the lower constricted portions of the two silica tubes define the column of liquid whose electrical resistance is being measured. The electrical resistance of the broad ex-

Jan 1, 1956

By F. G. Cottrell

AS previously announced, Van. H. Manning has resigned as director of the Bureau of Mines, effective June 1, to become director of research with the newly organized American Petroleum Institute. Doctor Manning has been connected with the Department of the Interior for 34 years, having been civil engineer with the Geological Survey, from 1885 to 1910, previous to his connection with the Bureau of Mines which was organized in the latter year. Doctor Manning was appointed to an administrative position in the new Bureau under Joseph A. Holmes, its first director, and on Jan. 1, 1911, was made assistant director. On Jan. 1, 1914, when Doctor Holmes had to relinquish active

Jan 1, 1920

By Hallan N. Marsh

The subject of mud sounds so simple, uninteresting and unimportant that it has failed to receive the attention that it deserves, at least as applied to the drilling of oil wells. As a matter of fact, it is one of the most complicated, technical, important and interesting subjects in connection with rotary drilling. In 1923, R. E. Colloml said "It should be possible to establish certain physical standards for mud fluid," but while considerable work has probably been done on the subject before and since that time, and numerous articles have been written, the progress of general knowledge of the subject and the application of better practices have not kept pace with other developments in rotary drilling, and physical standards cannot be considered as established. Mud is apt to be thought of as an accessible and cheap material, but its cost is likely to be an important factor in the total cost of drilling a well. Some wells "make" most of their own mud out of the formations drilled, but in most cases a great deal of mud-making material has to be supplied from more or less distant sources. Expenditures for mud materials by one California company totaled practically one-quarter million dollars during 1929 and averaged about $13 per rig per drilling day, or about $2000 per well. Under unfavorable conditions, mud cost may reach many times this figure. Parker2 says that in the Hobbs, N. M., field "as much as $75,000 has been spent on one well alone for mud and mud-weighting compounds."' Presumably this is an exceptional case. Unit cost of mud fluid will range from 10 c. per barrel, where suitable material is close at hand, to $1 where crude material is available at moderate price but must be hauled long distances, and on up to as much as $11 per barrel where high gas pressure requires the use of special processed weighting material. The cost of mud pales into insignificance, however, when the results of using improper mud are considered. Blow-outs and lost circulation are obviously the result of inadequate mud. Stuck drill pipe, whether or not twisted off, in many if not most cases probably is caused by cuttings settling out of the mud or the mud itself precipitating. Recent experi-

Jan 1, 1931

By B. Post, F. W. Glaser

Three borides of zirconium have been reported: ZrB,l ZrB2,2,3 and ZrB12, 4 The phase relationships, ranges of stability, and some physical properties of these compounds are described. THE zirconium borides differ considerably from one another, particularly with respect to their relative stabilities at high temperatures in the presence of carbon.4,5 ZrB2 is extremelv stable at all temperatures (to the melting point) in contact with carbon. Both ZrB and ZrB12 tend to decompose at elevated temperatures when carbon is present in excess of about 0.5 pct. ZrB forms ZrB2 and ZrC, and ZrB12 decomposes to form ZrB2 and a boron-carbide phase. In the ZrB12 preparation, boron present in excess of that needed to form ZrB2 reacts with carbon, if present, to form carbides, in preference to forming the higher boride. Similar instability of borides, other than diborides of the transition metals of the 4th and 5th groups of the periodic table, has been reported.5,6 special precautions had, therefore, to be taken to minimize carbon contamination in the preparation of ZrB and ZrB12. Reactions below 1400°C were carried out by heating powdered mixtures of zirconium hydride and boron in quartz tubes in a hydrogen atmosphere. For temperatures above 1400°C, reactions were carried out in graphite molds. Carbon contamination from the molds was minimized by employing extremely rapid heating rates to reduce carbon diffusion into the body of the specimen, and by subsequent "shaving" of sample surfaces that had been in contact with the graphite dies. A heating rate of about 2000°C per min was obtained by heating the dies (by direct conduction), using a current of 40,000 amp. Although this type of heating cycle apparently allowed little time for "homogenization," close approximations to equilibrium conditions were usually obtained as a result of the very strongly exothermic reactions between zirconium hydride and boron at elevated temperatures. Reproducibility of results in repeated runs under varying conditions was taken as a reasonable indication that equilibrium conditions had been effectively achieved. Quenching was accomplished by rapidly immersing the entire die, containing the reaction products, in water. Specimens could also be cooled at controlled rates by adjustment of the rate of flow of water through the water-cooled copper electrodes in contact with the graphite dies.

Jan 1, 1954

Jan 1, 1931

By Alan Stanley

THE MacIntyre Development of National Lead Co. is located at Tahawus, N. Y., in the heart of the Adirondack Mountains. Operations involve the mining and concentrating of a titaniferous iron ore to produce ilmenite and magnetite concentrates. A general description of the operation and metallurgy has been given by Frank R. Milliken.' Pigment plant production demands that the MacIntyre mill produce a 44.7 pct TiO, ilmenite concentrate. To achieve the required ilmenite grade and tonnage it is important that the table concentrate grade be closely controlled. Unfortunately, however, the titaniferous orebody which feeds the MacIntyre mill is not uniform. Ore dressing characteristics vary from one end of the orebody to the other, and from • one level to the next. The changeable nature of the mill feed precludes a single adjustment of the equipment for long periods of time. Thus the operators must constantly watch the equipment to insure a uniform concentrate from the fine and coarse tables and Wetherills, or dry magnetic separators. Chemical assaying of mill products requires about 4 hr from the time the sample is taken until assay results are obtained, and this is available only on a two-shift basis. The ore may change rapidly, even several times during a shift, so that assay results lose most of their control value by the time they are reported to the mill operating crew. Members of the crew have therefore tried to evaluate the table and Wetherill concentrate by visual inspection, since through long experience the shift operators, under most circumstances, can gage closely the grade of the mill products. However, there are times when the physical nature of the ore is radically different from normal. Under these conditions visual inspection is of no value, and at such times final ilmenite as low as 43 pct TiO, has been produced and shipped before the assay results have been received. The specific gravity method of assaying for TiO, has been attempted to eliminate the shipping of ilmenite below normal grade as well as to help control day to day and hour to hour mill production. Table I shows the minerals found in the MacIntyre ore along with their average weight proportions and specific gravities. The first two products considered for the specific gravity method were fine and coarse table concentrates. It was reasoned that these products were essentially ilmenite with the higher specific gravity gangue minerals. Since they were always produced the same way, and the desired grade of TiO, was always constant, the specific gravity of these materials would increase or decrease as the amount of ilmenite increased or decreased. Thus for table concentrates which assayed 40 pct TiOz a constant gravity would invariably be obtained, and as the TiO, value changed the specific gravity would change in direct proportion. The third product considered was Wetherill ilmenite. It was assumed that a desired grade of 44.7 pct Ti02 would also always contain the same amount and type of gangue minerals along with the ilmenite, and thus would always have the same specific gravity. As the TiO, value of the ilmenite concentrate changed so would its specific gravity. Dr. Kenneth Vincent, chief metallurgist of the Baroid Division of National Lead Co. at Magnet Grove, Ark., ran specific gravity tests on 17 samples of the desired products. The lowest specific gravity reading assayed the lowest in TiO, and as the specific gravity increased the trend was for the TiO, assay to increase, see Fig. 1. Since these results warranted further investigation, a 500-g capacity Torsion balance and 250 ml Le Chatelier specific gravity bottles were obtained. Shift samples of fine table concentrate, coarse table concentrate, and final ilmenite were tested. Each sample was split and 85 g weighed on the Torsion balance. The Le Chatelier bottle was filled with water to a zero mark. To avoid wetting the neck of the bottle it was found necessary to do this

Jan 1, 1953

By Alan Stanley

THE MacIntyre Development of National Lead Co. is located at Tahawus, N. Y., in the heart of the Adirondack Mountains. Operations involve the mining and concentrating of a titaniferous iron ore to produce ilmenite and magnetite concentrates. A general description of the operation and metallurgy has been given by Frank R. Milliken.' Pigment plant production demands that the MacIntyre mill produce a 44.7 pct TiO, ilmenite concentrate. To achieve the required ilmenite grade and tonnage it is important that the table concentrate grade be closely controlled. Unfortunately, however, the titaniferous orebody which feeds the MacIntyre mill is not uniform. Ore dressing characteristics vary from one end of the orebody to the other, and from • one level to the next. The changeable nature of the mill feed precludes a single adjustment of the equipment for long periods of time. Thus the operators must constantly watch the equipment to insure a uniform concentrate from the fine and coarse tables and Wetherills, or dry magnetic separators. Chemical assaying of mill products requires about 4 hr from the time the sample is taken until assay results are obtained, and this is available only on a two-shift basis. The ore may change rapidly, even several times during a shift, so that assay results lose most of their control value by the time they are reported to the mill operating crew. Members of the crew have therefore tried to evaluate the table and Wetherill concentrate by visual inspection, since through long experience the shift operators, under most circumstances, can gage closely the grade of the mill products. However, there are times when the physical nature of the ore is radically different from normal. Under these conditions visual inspection is of no value, and at such times final ilmenite as low as 43 pct TiO, has been produced and shipped before the assay results have been received. The specific gravity method of assaying for TiO, has been attempted to eliminate the shipping of ilmenite below normal grade as well as to help control day to day and hour to hour mill production. Table I shows the minerals found in the MacIntyre ore along with their average weight proportions and specific gravities. The first two products considered for the specific gravity method were fine and coarse table concentrates. It was reasoned that these products were essentially ilmenite with the higher specific gravity gangue minerals. Since they were always produced the same way, and the desired grade of TiO, was always constant, the specific gravity of these materials would increase or decrease as the amount of ilmenite increased or decreased. Thus for table concentrates which assayed 40 pct TiOz a constant gravity would invariably be obtained, and as the TiO, value changed the specific gravity would change in direct proportion. The third product considered was Wetherill ilmenite. It was assumed that a desired grade of 44.7 pct Ti02 would also always contain the same amount and type of gangue minerals along with the ilmenite, and thus would always have the same specific gravity. As the TiO, value of the ilmenite concentrate changed so would its specific gravity. Dr. Kenneth Vincent, chief metallurgist of the Baroid Division of National Lead Co. at Magnet Grove, Ark., ran specific gravity tests on 17 samples of the desired products. The lowest specific gravity reading assayed the lowest in TiO, and as the specific gravity increased the trend was for the TiO, assay to increase, see Fig. 1. Since these results warranted further investigation, a 500-g capacity Torsion balance and 250 ml Le Chatelier specific gravity bottles were obtained. Shift samples of fine table concentrate, coarse table concentrate, and final ilmenite were tested. Each sample was split and 85 g weighed on the Torsion balance. The Le Chatelier bottle was filled with water to a zero mark. To avoid wetting the neck of the bottle it was found necessary to do this

Jan 1, 1953

By C. T. Liu, J. Gurland

The deformation behavior in tension of spheroidized carbon steels was studied at room temperature as a function of carbon content, 0.065 to 1.46 wt Pct, and carbide particle size, 0.88 to 2.77 p. It was found that the Hall-Petch strength-grain size relation is directly applicable to the yield and flow stresses of the two lower-carbon steels , 0.065 and 0.30 pct C. The strength data for the medium- and high-carbon steels, 0.55 to 1.46 pct C, also satisfied the Hall-Petch relation, provided that these data are based upon the particle spacing. Beyond 4 pct strain, the flow stress data of all the steels studied could be represented by the same Hall-Petch relation with dinerent spacings for grain boundary and particle strengthening. The behavior of the higher-carbon steels was consistent with the postulated formation of a dislocation cell network during processing and initial deformation (up to 4 pct strain). The cell size was assumed to be equal to the planar particle spacing. The true stress at the ultimate tensile strength was also found to be a function of the particle spacing. At a given temperature and strain rate, the yield and flow stresses of carbon steels depend on the type and dimensions of the microstructure. Starting with the work of Gensamer et al. in 1942,' experimental studies on pearlitic and spheroidized carbon steels revealed that the strength of steels is a function of two main parameters: the ferrite grain size2'3 and the carbide particle spacing;1'4'5 on this basis, two different strengthening mechanisms have been developed to apply to steels of low and high carbon contents, respectively. In polycrystalline iron and mild steels the grain boundaries are regarded as the major structural barriers to slip. The relation between strength and grain size is generally represented by the Hall-Petch equation which is based on a linear proportionality between strength and the inverse square root of the average grain size.2'3y677 However, Gensamer et al.' and Roberts et related the yield strength of medium -and high-carbon steels to the carbide particle spacing alone, and they found a linear relation between the logarithm of the mean free path in the ferrite and the yield strength in both spheroidized and pearlitic steels. By means of the electron microscope, Turkalo and LOW' extended the study to finer structures; they concluded that the logarithmic relation is not valid for the entire range of microstructures unless grain boundaries are also included in the measurement of the mean free path. For the specific case of spheroidized steels, Ansell and aenel' found that the yield strength data,4'5 when plotted as a function of mean free path, fit the Hall-Petch equation; however, T'ysong found that the same data fit the 0rowanl0 relation if a planar inter-particle spacing is used. Recently Kossowsky and ~rown" studied the strength of prestrained spheroidized steels, 0.48 and 0.95 pct C, and concluded that the strength due to the carbide dispersions varies linearly with the reciprocal of the square root of the mean free path between carbide particles and dislocation networks. Such networks were first observed by Turkalo." The conclusion common to all these studies is that the available slip distance in the ferrite is the most important variable in determining strendh. Previous work on carbon steels is restricted to limited composition and strain ranges. The mechanism which governs the flow properties is not clearly understood, and, in particular, little is known about the composition dependence of the transition between grain boundary strengthening and particle hardening. The purpose of the present work is to investigate the strengthening mechanism in spheroidized steels over a wide range of carbon content, 0.065 to 1.46 wt pct, and plastic strain, yielding to necking. The spheroidized structure was chosen because of its relative simplicity and the relative ease of control and measurement of the structural parameters. The experimental work is limited to tensile testing at room temperature at constant extension rate. The effects of the carbide particles on the fracture behavior of spheroidized steels are discussed elsewhere.13 EXPERIMENTAL PROCEDURE Eight different grades of vacuum-cast carbon steels were supplied in the form of forged and rolled plate by the Applied Research Laboratory of the U.S. Steel Corp. The compositions furnished with these steels are given in Table I; the carbon content ranges from 0.065 to 1.46 wt pct, or from 1.0 to 22.3 vol pct of carbide. The steel plates were cut transversely into rods a little larger than the test specimens, 1 in. gage length, i in. diam. The rods were austenitized in air (enriched with CO by a consumable carbon-rich muffle) at 50° C above theA, orA., temperature for 2 hr and then quenched in oil with vigorous stirring. The as-quenched rods were tempered in two stages in order to obtain the desired distributions and sizes of carbide particles. The rods were first tempered at 460° C for 10 hr and then at 700" C for periods ranging from 4 hr to 3 days, in vacuum. After final machining, all specimens were vacuum-annealed again at 650°C for 1 hr in order to relieve residual stresses. The tension tests were carried out in two steps. The initial part of the load-strain curve, up to about 2 pct strain, was determined on a Riehle testing machine with an extensometer of small strain range, 4 pct strain, in order to obtain the yield and initial flow piopertiesi As soon as the first part of the test was finished, the specimen was placed in an Instron testing machine equipped with a strain gage extensometer with a maximum strain range of 50 pct. The load-strain curve to fracture was

Jan 1, 1969

By Ben L. Seegmiller

Roof, pillar and floor stability is a most important requirement in underground coal mines because it represents the leading cause of fatalities. In future coal mine planning the geotechnical aspects must often be minimized owing to unavailability of data. It is, therefore, very important to include a geotechnical investigation as part of the coal exploration program. Data which should be collected basically include the geological discontinuity characteristics, the rock strength characteristics and the groundwater aspects. Many times the only source of such data is the exploration boreholes. Therefore, an emphasis must be made to extract the maximum information from the core and the borehole. Data collection methods can include the preparation of detailed geotechnical logs for the roof, coal and floor. Laboratory strength testing will provide estimates of the mechanical properties of the various lithologic types. Slaking and swelling tests provide an insight into the stability characteristics of the rock materials immediately enclosing the coal seam. The boreholes may be used to provide permeability and pressurization data. Having developed a suitable geotechnical data base allows various stability prediction methods to be used. These include a geotechnical appraisal of the roof and floor units, depositional environment methods, multiple overlay techniques, hazard analysis techniques and classification/rating systems for roof and floor. The basic geotechnical data and the stability prediction methods form a basis upon which preliminary rock mechanics designs may be developed. Of particular importance to future coal mining are those designs relating to longwall mining because most companies are thinking in terms of the greater safety and greater productivity offered by longwalls. Items which should be ad- dressed when considering a longwall system include the panel layout in terms of a total mining plan, strata mechanics, roof/floor bearing capacities, face support requirements, face length, entry and pillar

Jan 1, 1983

By R. C. Ernrnons, Ray Wilcox

RECENTLY completed experimental work, carried out in the department of geology at the University of Wisconsin, aiming at a prevention of silicosis in industry has been reported in the American Mineralogist. A vast amount of work on silicosis has been reported in the literature, the clinical aspects having been especially well covered. A host of critical observations have been made on the variations in the nature of the silicosis problem in different environments, and a great deal of valuable experimental work has helped to clarify these observations. At present a greater amount of information of a critical sort is available than ever before, which affords a more sound basis for interpretive thought. It has been observed in industry that essentially pure silica dust gives rise to silicosis. Jones would modify this conclusion to place the responsibility on sericite, a silicate mineral present in the siliceous dust. Material such as granite dust, which carries a high free silica (quartz) content, is also a silicosis hazard. But sericite, too, is usually present in granite. In general it is widely believed that silicosis is caused by the presence in the lung of silicic acid regardless of the source. This view is adopted here.

Jan 1, 1937

By AIME AIME

PRIZES totaling $450 were awarded at the Annual Meeting luncheon on Monday, Feb. 9, to the winners of the third national student prize paper contest. The undergraduate prizewinners, each of whom received a check for $100, were as follows: Mayo W. Lanning, Lafayette College, for his paper entitled ?Some Aspects of the Mining Methods Employed at the Scrub Oak Mines of the Alan Wood Steel Company,? (entered by the Lehigh Valley Section). Charles F. Parent, Montana School of Mines, for his paper entitled ?Relationships of Manganese Minerals in the Butte District,? (entered by the Montana Section). Harry Czyzewski, University of Illinois, for his paper entitled ?A Metallurgical Study of Cast Irons Used for Glass Molds,? (entered by the Chicago Section).

Jan 1, 1942

Jan 1, 1924

By G. C. Rauch, T. H. Courtney, J. Wulff

The superconducting behavior of Nb-Ti alloys containing 40 and higher wt pct of Nb and variable oxygen content was studied as a function of thermomechanical processing. Critical current density (Jc) us applied transverse magnetic field (H) data were obtained for 0.010 in. diam wires at 4.2° Kin steady fields up to 120 kOe. The precipitate responsible for increase in Jc in each of the alloys studied was related to niobium and oxygen content. In alloys containing 40 to 60 wt pct Nb with less than about 1600 ppm of oxygen, w precipitation in the range 350° to 450°C appears to be responsible for the maximum value of Jc observed. In alloys of higher oxygen content (-2500 ppm), the oxygen-enriched a phase which precipitates in the temperature range 450° to 550°C is a more effective fluxoid pinner. Maximum Jc in low oxygen (350 ppm) 80 wt pct Nb alloys was achieved by 600°C aging heat treatments. Measurements of resistive critical field also reflect the changes in composition accompanying precipitation in these alloys. It is well known that the superconducting critical current density, Jc, of solid solution superconducting alloys can be increased by precipitation heat treatments.1-4 The precipitate, to serve as an effective superconzlucting fluxoid pinner and increase Jc, must be of proper size and spacing.' Its electronic properties must also be different from those of the matrix.6 As in age-hardenable systems, optimum temperature and time of aging are dictated by the composition and history of the particular solid-solution alloy under consideration. The alloy diagram of Ti-Nb7-9 shown in Fig. 1 is typical of ß-stabilized Ti alloys. Precipitation to achieve high Jc in Ti-Nb and Ti-Ta alloys is usually carried out in what is believed to be a two-phase a + ß region.1,2,4,10 Previous work on Ti-Nb4,11 and on other ß-stabilized systems such as Ti-V, Ti-Mo,12-14 has shown, however, that the first precipitate to appear is not necessarily (Y. Under specific conditions the meta-stable w phase is precipitated instead. A further complication arises in such alloys from the strong influence of contained oxygen on the phase stability and on the kinetics of precipitation.15,16 The superconducting critical current density of Nb-Ti alloy containing less than 36 wt pct Nb has been studied by Vetrano and Boom1 and Kramer and Rhodes.4 The most effective aging temperature was found to be about 425°C; fluxoid pinning was attributed to the precipita- tion of a by Vetrano and Boom and of w by Kramer and Rhodes. Although the latter workers used recrystal-lized material and the former cold-worked, studies carried out in our laboratory lead us to believe that the type of precipitate responsible for increased Jc is unaffected by prior cold-work.17 That other types of precipitates may also be effective, especially in higher oxygen-containing alloys, has been demonstrated by Reuter, et al.2 in this laboratory with the aid of electron microscopy. Reuter et al. found that at an aging temperature of 600°C, fee-TiO is precipitated, resulting in high values of Jc. Even higher values of Jc were observed after heat treatment at 500°C, but the precipitate could not be indexed as fee-TiO. Whether the precipitate was oxygen-rich w or a could not be clearly distinguished. The work nevertheless indicates that appreciable amounts of oxygen alter the nature of the phases precipitated at different temperatures, at least in alloys containing more than 36 wt pct Nb. Since such compositions are more readily worked into suitable wire than lesser niobium content alloys, it was decided to study the response to aging of the alloy compositions reported in the present paper with the hope of clarifying the effect of composition on the precipitation processes responsible for high values of Jc. I. EXPERIMENTAL Nb-Ti alloys containing 40, 50, 60, and 80 wt pct Nb were prepared by are-melting 35 g ingots of iodide crystal bar titanium and electron-beam melted niobium.

Jan 1, 1969

By Arthur F. Taggart, T. C. Fitt, A. W. Thomas

IT was noticed early by operators that high recoveries and flocculation of the sulphide minerals were closely correlated in agitation-froth flotation. Later, this readily visible flocculation was found almost invariably to be due to the binding together of the oiled sulphides by minute air bubbles, and is now known to be characteristic of pulps in which at least one of the mineral species is coated with an insoluble collecting oil. In 1930 it was reported1 that in differential flotation a correlation exists between Brownian movement of particles in the pulp and their nonfloatability, and that Brownian movement and dispersion are likewise correlated, whence it would appear to follow that dispersion of a mineral particle in a flotation pulp denotes a particle condition unfavorable to flotation. In 1934 it was postulated2 that Brownian movement, dispersion and nonfloatability all flow from the condition of the surface of the dispersed particles. It was also postulated at that time that the surfaces of dispersed particles are ionized, the ionized compound being a product of reaction between a component of the particle and a. component of the pulp, of a mass solubility of the general order of a fraction of a milligram to 15 to 20 mg. per liter. It was then further asserted, and has since been confirmed by Bankoff,3 that sulphides so conditioned with soluble collectors as to be floatable flocculate without the intervention of air bubbles as binding media. The present paper comprises an inquiry into the nature of the bound and counter ions in zinc sulphide dispersed by sodium arsenate. A part of its findings was mentioned in the 1934 paper above cited.2 The tests show that: I. When powdered granular zinc sulphide is immersed in aqueous solutions of sodium arsenate, arsenate ion is abstracted from solution and anchored to the solid surface, while sulphate and lower sulphoxy ions are concurrently displaced therefrom in substantially stoichiometric quantities. 2. The ion counterbalancing the anchored arsenate ion is zinc. 3. Dispersion and Brownian movement of zinc sulphide are concurrently maxima at an arsenate-ion concentration lying between 0.01 and 0.001-molar sodium arsenate. 4. Any condition or reaction that tends to remove the zinc arsenate coating from the zinc sulphide particles decreases dispersion and Brownian movement concurrently. EXPERIMENTAL Three samples of zinc sulphide were used. Lot I was C.P. zinc sulphide, washed well beyond absence of chloride, as shown by test with silver ion. Lot 2 was prepared by precipita-

Jan 1, 1943

By C. L. Mantell

When considered from the viewpoint of world annual output, tin is one of the rarest metals. Its annual production is exceeded by that of iron, copper, lead, zinc. aluminum, magnesium; probably by that of the ferroalloys of manganese, chromium, and silicon, and possibly by the world production of sodium; while it exceeds only the output of such common metals as nickel, antimony, mercury, tungsten, molybdenum, silver, gold and the precious metals. Cassiterite, or tinstone, until the second World War was the only mineral that was an important source of tin. This mineral is frequently called "tin ore." The use of the term should be restricted to the ore containing the mineral, and not, in addition, to the concentrates of the mineral obtained from the ore or from stanniferous alluvial deposits. There is a general misuse of the term "tin ore" in the Malay Peninsula and adjacent localities, particularly where most of the mineral is obtained from secondary stanniferous deposits. The term "cassit-erite" is exclusively used in mineralogical, geological, and other scientific writings; it is unfortunate that it is not mole frequently used when referring to the occurrence of the mineral on an economic scale. Ores "Tinstone" js a very convenient old English term deserving a more frequent use. Tinstone is a dioxide of tin, or stannic oxide. When chemically Pure, as in the very rare transparent variety, it has a metallic content of 78.6 per cent tin. Frequently, however, the crystals and grains contain appreciable amounts of impurities, chiefly iron and tantalum. The impurities here referred to are those actually in the mineral itself. Tinstone usually has a deep brown or black color with an adamantine luster. Several other colored varieties are known, among them red ruby tin, yellow rosin tin, and yellow wax tin. the names jn each case being descriptive of the mineral's appearance. Ainalite is a variety of cassiterite con-taining almost g per cent of tantalum pentoxide. Sparable tin, tooth tin, and needle tin, as a result of their acute dite-tragonal pyramidal crystalline form, re-ceive their names from their crystallo-graphic appearance. Wood tin is a compact variety of cassiterite composed of radiating fibers resembling dry wood. Toad's-eye tin is a similar variety on a smaller scale in which the fibers appear to resemble the eye of a toad. Stream tin is water-worn tin-stone. Float tin is sometimes employed to describe the cassiterite occurring in soil derived from the weathered surface of a mineralized area. Stannite is an ore of tin of lesser impor-tance than cassiterite. It is a sulphide of tin, copper, and iron, sometimes known as tin pyrites or bell-metal ore. Its chemical com-position is sometimes expressed by the for-mula Cu,S.FeS.SnSz with zinc usually present in varying quantities. The tin con-tent varies from 22 to 27 per cent and there is about 29 per cent of copper, 13 per cent of iron, and 30 Per cent of sulphur.

Jan 1, 1944

By Alan Stanley

THE Maclntyre Development of National Lead Co. is located at Tahawus, N. Y., in the heart of the Adirondack Mountains. Operations involve the mining and concentrating of a titaniferous iron ore to produce ilmenite and magnetite concentrates. A general description of the operation and metallurgy has been given by Frank R. Milliken.1 Pigment plant production demands that the MacIntyre mill produce a 44.7 pct. TiO2 ilmenite concentrate. To achieve the required ilmenite grade and tonnage it is important that the table concentrate grade be closely controlled. Unfortunately, however, the titaniferous orebody which feeds the Maclntyre mill is not uniform. Ore dressing characteristics vary from one end of the orebody to the other, and from one level to the next.. The changeable nature of the mill feed precludes a single adjustment of the equipment for long periods of time. Thus the operators must constantly watch the equipment to insure a uniform concentrate from the fine and coarse tables and Wetherills, or dry magnetic separators. Chemical assaying of mill products requires about 4 hr from the time the sample is taken until assay results are obtained, and this is available only on a two-shift basis. The ore may change rapidly, even several times during a shift, so that assay results lose most of their control value by the time they are reported to the mill operating crew. Members of the crew have therefore tried to evaluate the table and Wetherill concentrate by visual inspection, since through long experience the shift operators, under most circumstances, can gage closely the grade of the mill products. However, there are times when the, physical nature of the ore is radically different from normal. Under these conditions visual inspection is of no value, and at such times final ilmenite as low as 43 pct TiO2 has been produced and shipped before the assay results have been received. The specific gravity method of assaying for TiO2 has been attempted to eliminate the shipping of ilmenite below normal grade as well as to help control day to day and hour to hour mill production. Table I shows the minerals found in the Maclntyre ore along with their average weight proportions and specific gravities. The first two products considered for the specific gravity method were fine and coarse table concentrates. It was reasoned that these products were essentially ilmenite with the higher specific gravity gangue minerals. Since they were always produced the same way, and the desired grade of TiO2 was always constant, the specific gravity of these materials would increase or decrease as the amount of ilmenite increased or decreased. Thus for table concentrates which assayed 40 pct TiO2 a constant gravity would invariably be obtained, and as the TiO2 value changed the specific gravity would change in direct proportion. The third product considered was Wetherill ilmenite. It was assumed that a desired grade of 44.7 pct TiO2 would also always contain the same amount and type of gangue minerals along with the ilmenite, and thus would always have the same specific gravity. As the TiO2 value of the ilmenite concentrate changed so would its specific gravity. Dr. Kenneth Vincent, chief metallurgist of the Baroid Division of National Lead Co. at Magnet Grove, Ark., ran specific gravity tests on 17 samples of the desired products. The lowest specific gravity reading assayed the lowest in TiO2 and as the specific gravity increased the trend was for the TiO2 assay to increase, see Fig. 1. Since these results warranted further investigation, a 500-g capacity Torsion balance and 250 ml Le Chatelier specific gravity bottles were obtained. [ ] Shift samples of fine table concentrate, coarse table concentrate, and final ilmenite were tested. Each sample was split and 85 g weighed on the Torsion balance. The Le Chatelier bottle was filled with water to a zero mark. To avoid wetting the neck of the bottle it was found necessary to do this

Jan 1, 1952

By F. H. Daniels

IN this, paper it is my intention to, call your attention to* a few of the many producers using blast, now, in common use in Sweden, and also those constructed by the Washburn & Moen Manufacturing Company at their Quinsigamond Works. During a prolonged stay in Sweden the writer had an opportunity

Jan 1, 1881

By C. R. Kuzell

The Editor desires to call attention to the charts in the paper of the above title which were published in the August Bulletin on pages 2190 and 2191. It was impracticable to include in the Bulletin. charts of sufficient size to be used as working diagrams for the direct determination of operating values, but the Institute is prepared to furnish copies of these charts on a large-size scale, at a moderate cost, to those who desire to have them for this purpose. CORRECTIONS Page 2185, line 3. For "is accessory apparatus" read "in accessory. apparatus." Page 2188. Substitute for lines 11 and 12: Nitrogen, oxygen, carbon monoxide, Cp = 6.50 + 0.0010T Hydrogen, Cp = 6.50 + 0.0009T

Jan 9, 1914