Search Documents

By T. A. Wilson, S. L. Hoyt

THE plastic deformation of slender single crystals of zinc has been described in some detail in the paper by Mark, Polanyi and Schmid,1 which has become a classic, and also by one of the present authors in a somewhat shorter account.' The study of single-crystal zinc is termed classical because zinc single crystals offer, perhaps, the best material yet available for the study of atomic behavior during deformation and the effect known as "strengthening" in metals. A considerable amount of additional work has also been done on single-crystal zinc, but as it is not closely related to the present paper it will not be considered. Throughout all the former work, the mechanism of plastic deformation first described by Mark, Polanyi and Schmid has been assumed to hold. This may be said to offer the strongest confirmation of its correctness. Even so, the picture of the process has never been as completely portrayed as is desirable. The first object of the present paper is to describe work that has been done in this field, and which is even yet being carried on, in the hope that a more complete picture may be obtained. Mathewson and Phillips' have recently described a new mechanism of the deformation of zinc based on their study of large rectangular crystals. One of their conclusions was that deformation produced twinning with a rotation of some of the basal planes into positions 94° removed from their original position; a position almost the same as that of the prismatic planes before twinning. A second conclusion was that fracture occurred along these basal planes in their new position, and, therefore that fractures previously regarded as prismatic were in reality basal. Such findings are of great significance and they raise a question as to the generality of such behavior. Professor Mathewson's opinion is that even the slender cylindrical single crystals behave in the same manner as his large rectangular crystals when strained by simple tension.

Jan 1, 1928

By C. R. Kuzell

ALTHOUGH furnaces constructed of refractory brick have been oper-ated for many decades, there has always been an unfulfilled desire by the operators for a less arduous and more satisfactory method of patching weak spots and burned-out zones in order to postpone and to effectively extend the termination of a furnace campaign. Not only has this desire frequently arisen when small spots have approached incipient failure while the furnace structure as a whole was still in good condition, but also when larger areas showed signs of needing replacement. The availa-ble methods have been arduous, sometimes dangerous, inefficient with respect to the life of new refractory material used, and nearly always have necessitated interruption of the continuity of the furnace operations and therefore reduction in furnace production during the period of time required for the repair work. Most of these older methods have involved the replacement of masonry by refractory shapes in the weakened areas. Many attempts have been made to develop a method of patching the burned-out areas by spraying granular refractory material upon old surfaces. While some success has been attained in attempts to renew the grooved, corroded side walls and fettling, and the edges of hearths, there have been no known successful applications of the spraying method in patching the underside of arches of operating furnaces. The method developed recently at the Clarkdale smelter of the United Verde Branch of Phelps Dodge Corporation, at Clarkdale, Ariz., and described in this paper, has been found to be not only convenient and successful with respect to patching vertical or inclined surfaces, but has met with a marked degree of success in patching the parts of furnace arches that are exposed to flame, the successful result being obtained with-out interruption or interference with the continuity of furnace operations. ? It may be described as a method of renewing the interior refractory sur-faces of operating furnaces by pneumatic spraying of an aqueous suspen-sion of finely divided particles of refractory material. It has been used

Jan 1, 1939

Discussion of the paper of S. E. Bretherton, presented at the Butte meeting, August, 1913, and printed in Bulletin No. 80, August, 1913, pp. 1481 to 1487. S. E., BRETHERTON, San Francisco, Cal.:-Since preparing my paper, our chemist, F. L. Wilson, has been experimenting with Leadville, Colo., oxidized zinc ore and Leadville zinc sulphides containing lead, operating upon 40-1b. lots at a time. His results on Leadville sulphides are as follows: The raw ore contained a trace of gold, 5.04 oz. of silver, 19.1 per cent of zinc, and 7.24 per cent of lead. After roasting the ore contained a trace of gold, 5.72 oz. of silver, 0.75 per cent of copper, 21.7 per cent of zinc, and 8.29 per cent of lead. The loss in weight by leaching was 38.8 per cent. The extraction was 42.8 per cent of the copper, 80.6 per cent of the zinc, 7.1 per cent of the lead, 0.64 per cent of the silver, and no gold. The little .silver that is extracted would be thrown down with the copper when precipitating it from the zinc and both thrown hack into the residue to be smelted. There would be no trouble in smelting the residue with nearly all the sulphur eliminated and containing less than 7 per cent. of zinc. On zinc carbonates containing silicates the results are not satisfactory. H. O. HOFMAN, Boston, Mass. (communication to the Secretary*) :¬The paper by Mr. Bretherton upon the application of ammonia and carbonic acid to the recovery of zinc as oxide from roasted sulphide ore is of interest to me, as the first installation of the Schnabel process for the extraction of zinc from a mixture of zinc oxide, lead oxide (with some cupric oxide), and pellets of enriched lead, produced in steaming liquated zinc-silver-lead crust of the Parkes process, was made at Lautenthal, Harz mountains, where I was chemist. In that capacity I carried out numerous experiments on the Schnabel process, was active in the erecting of the plant, and later had charge of it. After the Lautenthal plant had been in operation for some time a similar one was built at Hoboken-les-Anvers, but both have been abandoned, as the wet process could not compete with the distillation of the liquated zinc-silver-lead crust, now used universally in the Parkes process.

Jan 11, 1913

By H. E. Elliott, R. S. Busk, A. T. Peters

ONE of the problems of the fabricator of metals and alloys is the propensity of some composition ranges toward abnormal grain growth during certain stages of fabrication. In this respect magnesium alloys are no exception among alloys. Fortunately, convenient foundry control methods have been developed by which the abnormal grain growth possible in certain magnesium-alloy castings can be suppressed. An unusual characteristic of magnesium alloys, however, is that castings of some composition ranges are subject to local grain growth during heat-treatment without the necessity of intentional mechanical stressing of the part prior to heat-treatment. This effect occurs only under certain critical casting conditions, and only in certain alloys of greater than about 8.5 per cent aluminum content, such as C alloy (Mg, o per cent Al, 2 per cent Zn, 0.2 per cent Mn) and G alloy (Mg, i0 per cent Al, 0.2 per cent Mn). The first observation of this phenomenon in cast magnesium alloys occasioned much surprise, since it is not observed in other metals. Jeffries and Archer' have stated that "the grain size of cast metals, provided they have not been plastically deformed, cannot be changed by heating below the melting point." The study of the conditions leading to abnormal grain growth in cast magnesium alloys, and of the mechanism of this phenomenon, has led to some very interesting observations. Perhaps the most significant of these was the observation that stresses originating from cooling contraction in magnesium-alloy castings are the only stresses necessary, under certain conditions, to cause local recrystallization and subsequent grain growth in the casting during heat-treatment. of abnormal local grain growth was a definite problem in the production foundry on C alloy sand castings. Illustrated (Fig. r) is a picture of a casting scrapped because of this defect. A mottled effect is produced in coarse-grained areas by suitable etching solutions. The properties of metal in the affected area are much impaired by such grain coarsening. Ultimate tensile strengths of half the normal value have been measured in metal of this nature. In this paper are described the techniques that have been developed by The Dow Chemical Co. for studying, and in large measure solving, this production problem. Also discussed are studies of the mechanism by which excessive grain coarsening occurs, and the fundamental conditions that produce this effect. The abnormal grain growth discussed in this paper will be referred to as "germination," since this term has been defined' as any process leading to an abnormally coarse grain size. This paper deals only with abnormal local grain growth that may occur during the solution heat-treatment of certain magnesium-alloy castings, as dis-

Jan 1, 1945

By Francis H. Crockard

During the past five years we have probably witnessed greater technological advances than in any similar period. Industry and science have steadily marched ahead. The makers of iron and steel products have watched with great interest the development of streamlined trains, faster and safer airplanes, the entirely new science of air-conditioning and the widespread use of stainless steels. Since 1930, we have witnessed the erection of the world's largest suspension bridge, the largest and fastest ocean liner and the spectacular Boulder Dam, while even greater things are planned in these particular fields. Other industries, too, have been moving ahead rapidly. This advance in a few years has been caused primarily by the fierce competition of the depression. Now, more than ever, is the emphasis placed upon quality and service. Makers of southern merchant pig iron have been no exception and have been confronted with increasingly strict chemical specifications and with much greater stress on physical characteristics than ever before. For example, sulfur in the iron must be held very low, competition demanding that it be in the 0.020's and low 0.030's; silicon content must be held within a very narrow range, and definite requirements of phosphorus and manganese are an essential part of the specifications. Physical characteristics are becoming of increasingly greater importance. The introduction of triple-skimmed, slow-cooled iron several years ago was the first step in this direction. Now there are a few customers who buy iron by chemical analysis and physical appearance, having found that the analysis alone is an insufficient guide to their requirements. In addition to questions of quality, the subject of cost has greatly altered the southern furnaceman's viewpoint on many things. Formerly we had low-grade but cheap raw materials, but recent developments, such as greatly increased labor rates, have raised the cost of the same

Jan 1, 1936

By Francis H. Crockard

During the past five years we have probably witnessed greater technological advances than in any similar period. Industry and science have steadily marched ahead. The makers of iron and steel products have watched with great interest the development of streamlined trains, faster and safer airplanes, the entirely new science of air-conditioning and the widespread use of stainless steels. Since 1930, we have witnessed the erection of the world's largest suspension bridge, the largest and fastest ocean liner and the spectacular Boulder Dam, while even greater things are planned in these particular fields. Other industries, too, have been moving ahead rapidly. This advance in a few years has been caused primarily by the fierce competition of the depression. Now, more than ever, is the emphasis placed upon quality and service. Makers of southern merchant pig iron have been no exception and have been confronted with increasingly strict chemical specifications and with much greater stress on physical characteristics than ever before. For example, sulfur in the iron must be held very low, competition demanding that it be in the 0.020's and low 0.030's; silicon content must be held within a very narrow range, and definite requirements of phosphorus and manganese are an essential part of the specifications. Physical characteristics are becoming of increasingly greater importance. The introduction of triple-skimmed, slow-cooled iron several years ago was the first step in this direction. Now there are a few customers who buy iron by chemical analysis and physical appearance, having found that the analysis alone is an insufficient guide to their requirements. In addition to questions of quality, the subject of cost has greatly altered the southern furnaceman's viewpoint on many things. Formerly we had low-grade but cheap raw materials, but recent developments, such as greatly increased labor rates, have raised the cost of the same

Jan 1, 1936

Lake Superior Meeting . PAGE Gathmann, Emil.-Casting and Molding Steel Ingots. Discussed by J. W. Richards.. 2 McCaffery, R. S.-The Acid Bessemer Process. Discussed by Bradley Stoughton, J. W. Richards 3 Elliott, S. R.-Athens System of Mining. Discussed by F. W. Sperr, Lucien Eaton 4 Mercer, H. T. and Paulson, A. C.-Handling and Treatment of Rock-drill Steel at Copper Range Mines. Discussed by Harrison Souder, H. T. Mercer, W. H. Schacht, C. M. Haight 5 Hayden, J. E. and Eaton, Lucien.-Building Reinforced-concrete Shaft Houses. Discussed by William Kelly, T. L. Condron, Lucien Eaton 7 Eaton, Lucien.-Mechanical Ventilation at Lake Mine. Discussed by C. A. Mitke 8 Schacht, W. H.-Steam Regenerators Reduce Coal Consumption. Discussed by 0. P. Hood, W. H. Schacht ? 9 Linton, Robert.-Standardizing at North Butte Mining Co. Discussed by Grant H. Tod, C. A. Mitke 10 Smith, H. DeWitt and Sirdevan, W. H.-Mining Methods and Costs at United Verde Mine. Discussed by C. A. Mitke 12 Davy, Myron A.-Reflecting Microscope for the Mining Engineer. Discussed by C. P. Berkey, W. A. Rukeyser 14 , Norden, J. A. and Willson, A. R.-Hoisting Equipment at Utah-Apex Mining Co. Discussed by E. M. Norris 17 Aldrich, H. R.-The Dip Needle in Stratigraphy. Discussed by H. R. Aldrich, W. 0. Hotchkiss, Carl Zapffe, E. A. Kronquist 18

Jan 1, 1921

By Selma Hermann

For the past century, the so-called aluminum bronzes have been assuming a role of ever-increasing importance in the metallurgical field. The last quarter of that century has marked many efforts to find alloying elements that would alleviate some of the undesirable qualities of the aluminum bronzes-for example, the heterogeneity of the alpha solid solution and the extreme hardness of the beta. Much of this work, however, has been rather haphazard-compositions and heat treatment are usually so much at variance as to make comparison impossible. It is the object of this research to study the effect of certain percentages of common alloying elements on aluminum bronzes of analogous compositions and heat treatments. It is hoped that the material gathered here will at least serve as a basis for further systematic study.

Jan 1, 1930

By J. N. Breston, R. V. Hughes

Conclusions drawn by previous research workers with reSPect to the relation between Pressure gradients and/or velocity and oil recovery obtained by laboratory water flood tests have been in disagreement probably due to variable procedures and unnatural conditions and materials. The Bradford Laboratory of the Pennsylvania Grade Crude Oil Association as part of its secondary recovery research program has conducted nineteen water floods on two long cores of widely differing characteristics in an attempt to clarify this relationship and make it an aid in predicting flooding pressures in the field. Unlike previous research procedures the present experiments were conducted with the aim of duplicating field conditions as closely as possible by using long unextracted consolidated cores, a live crude, and natural brines for both flooding and, connate water content. Also, the pressure gradients and flooding velocities were representative of field conditions where similar sands were being flooded. Eleven floods on one core and eight floods on the other core showed increased recoveries and lower residual oil saturation with increased flood pressure gradients and flood velocities. A marked decrease in recovery was obtained from both cores at very low flood velocities. This pressure versus recovery relationship is shown to hold up to the point of water breakthrough and also up to the 100 and 1 produced water to oil ratio point. INTRODUCTION The possibility of water flooding oil sands was suggested by Carl1 of the Pennsylvania Geological Survey in 1880. It is not known when the practice was tried intentionally for the first time, but its beneficial effects were noted in the annual production rate of the Bradford field as early as 1907. The practice was illegal in Pennsylvania until 1921. Early water floods in the Bradford field usually consisted of shooting or splitting the casing secretly to permit subsurface waters to enter the producing sands under hydrostatic head. As it was noted that the benefits of water flooding seemed to be proportional to the quantity of water dumped into the well many also began to utilize surface sources after the practice became legal. It was probably during the middle 20's before many producers realized that the pressurehead of the water upon the producing sand determined the rate and quantity of water that would enter the sand. Hence, rate and quantity of production appeared to be a direct function of input pressures. By 1927 a few producers had ventured the installation of pressure pumps in order to increase water-input rates and production through the combination of hydrostatic and hydraulic pressures. The adoption of pressure flooding and the "five-spot" drilling pattern in the Bradford field were essentially simultaneous. Water-input pressures in 1930 seldom exceeded 300 p.s.i. at the well head or 1100 p.s.i. at the sand face. Since that time, water-flood producers in the Bradford-Allegany fields have gone to higher and higher pressure until today 600 p.s.i. at the well heads is called a low pressure flood. Many high pressure floods now operate at 1300-1400 p.s.i. at the well head. The limiting and advisable pressure at the sand face has been pronounced as that pressure just under what is required to lift the overburden or to cause formation parting: According to this rule any water flood operation utilizing well-head pressures nearly equal in pounds per sq. in. to 1.1 times the average depth in feet to the top of the producing sand would be considered as a high-pressure flood. Despite the higher pressure trends in the Bradford-Allegany field operations and the results of early laboratory water flooding research, the desirability and benefits of high input pressures are still questioned by many operators, particularly in midwestern water flood operations. The present paper recounts a series of 19 laboratory water floods using two long, consolidated cores of widely differing characteristics saturated with live crude and flooded with oil field brines in an effort to simulate field conditions under • various pressure gradients and flooding velocities. For both cores, higher recoveries and lower residual oil saturations were obtained at higher pressure gradients and flood velocities. This relationship is shown to hold up to the water breakthrough point and also up to the 100 to 1 produced water to oil ratio point.

Jan 1, 1949

By R. V. Hughes, J. N. Breston

Conclusions drawn by previous research workers with reSPect to the relation between Pressure gradients and/or velocity and oil recovery obtained by laboratory water flood tests have been in disagreement probably due to variable procedures and unnatural conditions and materials. The Bradford Laboratory of the Pennsylvania Grade Crude Oil Association as part of its secondary recovery research program has conducted nineteen water floods on two long cores of widely differing characteristics in an attempt to clarify this relationship and make it an aid in predicting flooding pressures in the field. Unlike previous research procedures the present experiments were conducted with the aim of duplicating field conditions as closely as possible by using long unextracted consolidated cores, a live crude, and natural brines for both flooding and, connate water content. Also, the pressure gradients and flooding velocities were representative of field conditions where similar sands were being flooded. Eleven floods on one core and eight floods on the other core showed increased recoveries and lower residual oil saturation with increased flood pressure gradients and flood velocities. A marked decrease in recovery was obtained from both cores at very low flood velocities. This pressure versus recovery relationship is shown to hold up to the point of water breakthrough and also up to the 100 and 1 produced water to oil ratio point. INTRODUCTION The possibility of water flooding oil sands was suggested by Carl1 of the Pennsylvania Geological Survey in 1880. It is not known when the practice was tried intentionally for the first time, but its beneficial effects were noted in the annual production rate of the Bradford field as early as 1907. The practice was illegal in Pennsylvania until 1921. Early water floods in the Bradford field usually consisted of shooting or splitting the casing secretly to permit subsurface waters to enter the producing sands under hydrostatic head. As it was noted that the benefits of water flooding seemed to be proportional to the quantity of water dumped into the well many also began to utilize surface sources after the practice became legal. It was probably during the middle 20's before many producers realized that the pressurehead of the water upon the producing sand determined the rate and quantity of water that would enter the sand. Hence, rate and quantity of production appeared to be a direct function of input pressures. By 1927 a few producers had ventured the installation of pressure pumps in order to increase water-input rates and production through the combination of hydrostatic and hydraulic pressures. The adoption of pressure flooding and the "five-spot" drilling pattern in the Bradford field were essentially simultaneous. Water-input pressures in 1930 seldom exceeded 300 p.s.i. at the well head or 1100 p.s.i. at the sand face. Since that time, water-flood producers in the Bradford-Allegany fields have gone to higher and higher pressure until today 600 p.s.i. at the well heads is called a low pressure flood. Many high pressure floods now operate at 1300-1400 p.s.i. at the well head. The limiting and advisable pressure at the sand face has been pronounced as that pressure just under what is required to lift the overburden or to cause formation parting: According to this rule any water flood operation utilizing well-head pressures nearly equal in pounds per sq. in. to 1.1 times the average depth in feet to the top of the producing sand would be considered as a high-pressure flood. Despite the higher pressure trends in the Bradford-Allegany field operations and the results of early laboratory water flooding research, the desirability and benefits of high input pressures are still questioned by many operators, particularly in midwestern water flood operations. The present paper recounts a series of 19 laboratory water floods using two long, consolidated cores of widely differing characteristics saturated with live crude and flooded with oil field brines in an effort to simulate field conditions under • various pressure gradients and flooding velocities. For both cores, higher recoveries and lower residual oil saturations were obtained at higher pressure gradients and flood velocities. This relationship is shown to hold up to the water breakthrough point and also up to the 100 to 1 produced water to oil ratio point.

Jan 1, 1949

ALABAMA Altoona -Cain, J Anniston -Cowie, L K Heimrod, A A White, H E Bessemer-Abbott, C C Ball, E M Mitchell, F R Thompson, N E Birmingham -Adler, T E Aldrich T H Aldrich, T H, Jr Blackburn, A R Bush, 117 W Clark, G H Cowin, P G Crane, W R Crawford, G G Crockard, F H Darnelspn, G E Davis, C B

Jan 1, 1923

By Frank Harwood Riddle

Products made from the ores of the sillimanite group, and synthetic substitutes for them, have unique properties, and service tests prove that they are playing, and will continue to play, a major part in improvements in metallurgical processes. Also, they are examples of how comparatively useless, rare, or "museum" minerals have been made available in commercial quantities. Until research developed uses for them, the minerals had been observed only in small, scattered masses, or crystals. Improvements in ceramic processes and compositions have come about very gradually. In the last 10 or 15 years, several outstanding developments have been made. Of greatest interest to the mining and metallurgical engineers are those affecting the composition, necessitating the mining of new minerals, and improvements in ceramic products used in metallurgical processes. Sillimanite and Mullite Sillimanite (Al2O3.SiO2), then known as Fibrolite, according to Dana,' was first reported in 1792. In 1796, cyanite (Al2O3.SiO2) was first described.2 In 1873, Behrens published results of his microscopic study8 of porcelain. He showed that it contained what appeared to be crystals, which dissolved less readily than quartz and glass in hydrofluoric acid. Hussak4 described the presence of needlelike crystals as occurring in some instances in small amounts in certain porcelains. In 1908, Plenske and Zoellner both studied porcelain structure.5 Plenske observed that "sillimanite" might be present in masses of exceedingly minute grains which apparently were amorphous. Zoellner advanced the theory that the needlelike crystals were formed by a molecular change in the clay,

Jan 1, 1932

By Charles Malcolmson

IN the United States, improvements in methods of combustion have made possible the use of the smaller sizes of anthracite. This coal is now being reclaimed from the culm banks accumulated by the miners in the more prodigal years. To-day the freshly mined "slush" is segre¬gated and stored against the time when, through briquetting or some other means, it may be utilized as a commercial fuel. For many years Europe has achieved enviable results in the conservation of her small coal by briquetting. This profitable industry, first placed on a commercial basis in France in 1842, has grown to such magnitude that the "'production during 1913 exceeded 36,000,000 short tons. Briquets produced in Great Britain are used principally for steam purposes and the greater part of the output is either exported or taken by the Admiralty. On the Continent the briquets are sold in all branches of the coal trade. The French railways consume from 16 to 40 per cent. of their fuel in briquet form, and in Germany the lignite briquets, (of which 20,000,000 tons were produced in 1913) are as familiar and interesting to the American traveler as the huge porcelain stoves in which they are burned. It is not strange, therefore, that aggressive and far-sighted promotors heralded this means of converting our ubiquitous coal waste into revenue. To the superficial student the briquetting process seemed so simple as to make success easy. It is for this reason principally that the path of the industry in America has been strewn with failures. The rash enthusiast had either not worked out the mechanical problems involved or had failed to grasp the local conditions under which the briquets must be made and sold. It may be confidently stated, however, that in spite of the many vicissitudes through which it has passed, coal briquetting is now an accomplished economic success in this country, and as a profitable adjunct to the coal industry it has come to stay.

Jan 2, 1915

By I. S. Levy, J. L. Brimhall, B. Mastel

Specimens of' Hastelloy X-280, a low-cobalt version of the solid-solution- hardened nickel-base alloy Hastelloy X, were given a series of thermomechanical treatttzents. They were then Lensile-tested at room temperature and 1350°F. The Microstructures of the specimens tested at 1350°F were studied by electron Microscopy. Microscopy showed that dislocation tangling, caused by the cold working, mas still in evidence after aging-for 24 hr to temperatures as high as 1550oF. (Cr, Mo)23 C6, (Fe, Mo)6 C'. as well us an unidentifiable phase precipitale due to the combination of the thermomechanical treatments and subsequent tensile strain. The room -temperature and 1350°F tensile properties show a general increase ill strength and decreccse in ductility with increusing cold-work level. This is due to the dislocation taangling-. PerLurbatiot~s to this general trend occur- due to solid-solution weakening at the higher cold-work levels as a direct result of the preciplitation reactions. THE requirements for corrosion resistance and high-temperature strength place nickel-base alloys among the more promising materials for advanced nuclear reactor applications. However, when these alloys are irradiated at service temperatures, they generally suffer severe embrittlement'" and reduction in rupture life.3 Certain experimental treatments resulted in improvements in the tensile and stress-rupture properties of Hastelloy X-280, a solution-hardened nickel-base alloy.' To provide a basis for understanding these improvements, unirradiated tensile specimens were examined by electron microscopy. The results are reported in this paper. EXPERIMENTAL DETAILS Material. Hastelloy X-280, a low-cobalt version of Hastelloy X, is a member of the solution-hardened class of nickel-base alloys. The Hastelloy X-280 was obtained from 4- and 1-in: thick plates in the mill -annealed condition. Table I gives the chemical composition of the material as reported by the National Spectrographic Laboratories. ~x~erimental Treatments. Plates of suitable size, 12 by 3 by 1 in., or by + in., were cut under a water jet from the stock material and examined ultrasonic -ally for homogeneity of grain size and absence of voids. The acceptable plates were solution-treated at 2150°Ffor 1 hr and air-cooled. These plates were then reduced in thickness by cold rolling 0, 10, 15: or 20 pct along the original rolling direction. The plates were machined into buttonhead tensile specimens with a gage diameter of 0.125 in., with a gage length of 1.125 in., and with their tensile axes parallel to the rolling direction. The specimens were examined for quality of finish with a penetrant dye, ultra son ically checked for voids, and finally given a dimensional tolerance check with an optical comparator. The acceptable specimens were aged for 24 hr at either 1000" or 1500 F and air-cooled. These specimens were then held at 540°F in a water loop for approximately 18 days to qualify as controls for similar specimens irradiated under the same conditions of time, temperature, water chemistry, and flow rate. Table U summarizes the treatments. These treatments were investigated to establish whether prior precipitation and stabilization of carbide phases at strain sites within the matrix could reduce the amount of carbides available for precipitation at grain boundaries during service. Tensile-Test Conditions. Specimens were tested to fracture at room temperature or 1350 F in air on an Instron tensile-testing machine at a crosshead speed of 0.05 in. per min. The time for the furnace to reach equilibrium at 1350°F was approximately 30 min; soak time prior to testing was 15 min; and test duration was approximately 5 min.

Jan 1, 1968

By H. H. Stoek

The origin of the Mine-Rescue Service of the State of Illinois can be traced to two distinct sources, the work of the Rescue Station at Urbana and the Cherry disaster. During the early part of the year 1909, the Technologic Branch of the U. S. Geological Survey, now the Bureau of Mines, in connection with the Illinois Geological Survey and the College of Engineering of the University of Illinois, established at the University of Illinois, in Urbana, a branch rescue-station to supplement the work of the Pittsburg station of the Geological Survey. As a result of the work of training at the station in Urbana by R. Y. Williams, mining engineer, and James Webb, foreman of the Bureau of Mines, and the use of the helmets at several mine-accidents in the State of Illinois, the people of the State were somewhat familiar with oxygen-helmets when the Cherry disaster occurred, in November, 1910. The oxygen-helmets were successfully used in connection with that disaster, and upon the recommendation of the Illinois Mining Investigation Commission, the Legislature of the State, assembled in special session during the winter of 1910, passed a bill appropriating $75,000 for the erection and maintenance of three rescue-stations, stipulating that they should be situated in the northern, central, and southern parts of the State. The Act also provided that the stations should be in charge of a Commission of seven, two representing the United Mine Workers of Illinois, two the mine-operators, one the Federal Bureau of Mines, one the State mine-inspectors, and one the Department of Mining Engineering of the University of Illinois. This Commission was called together by the Governor of the State, Aug. 2, 1910, and since that time three stations have been placed, built, and equipped: at La Salle for the northern

Jan 1, 1912

Featured at the 1977 SME-AIME Fall Meeting in St. Louis is a Lead-Zinc Update, organized to complement the 1970 AIME World Symposium on Mining and Metallurgy of Lead and Zinc, also held in St. Louis. The 21 papers comprising the Update are to be presented during four technical sessions at the Fall Meeting; in addition, the papers have been collected in a bound book available at meeting time.

Jan 9, 1977

By Thomas C. Baker

The Fresnillo unit of the Mexican Corporation, S. A., is situated at the old historic mining town of Fresnillo, Zacatecas, Mexico, 33 miles north of the city of Zacatecas and 750 miles south of El Paso, Tex. It is connected with the Mexican Central Railroad by a broad-gage spur 5.5 miles long, belonging to the company. Fresnillo is surrounded by a broad semi-arid valley on the Mexican plateau at an elevation of 7300 ft. The monotony of the valley is broken by a number of low hills. Near the town of Fresnillo is the " Cerro de Proano," an elliptic-shaped hill of gentle slope, rising out of the plain to a height of 325 ft.; the base has a major axis of 4500ft. and a minor axis of 3000 ft. In this hill is the silver-bearing mineralized zone, which comprises past and present mining operations. (In this paper money values are expressed throughout in American currency and the dry short ton of 2000 lb. is used.) The discovery of ore at Fresnillo is credited to the Spaniards, soon after the conquest of Mexico. There are, however, no authentic records to show the amount of work done by them. In 1832, the State of Zacatecas took possession of the property and operated it. Evidently the rich ore above the horizon of the plain had been fairly well exhausted, as an old record states that thirty shafts were used for unwatering, requiring 300 men and 1500 animals. The cost of pumping alone amounted to $150,000 a year. In spite of the fact that cheap convict labor was used, mining costs were reported as $20 and treatment charges as $20 per ton. In 1835, the state was obliged to seek foreign capital, and a company formed in London secured a controlling interest in the property. This new organization sank two shafts, one 11 by 19 ft. and the other 10 by 15 ft., to unwater the mines and extract ore. Large Cornish pumps were purchased in England and hauled overland from Vera Cruz; engines also were installed to operate the arrastres (grinding mills) in the patio process of ore treatment. Substantial buildings were erected and operations were conducted on a large scale, for that period. The patio, the largest in Mexico, was 1150 ft. square. The costs for 1850 were:

Jan 1, 1925

By R. L. Templin

The increasing use of aluminum and its alloys in commercial fields tias demanded a better understanding of their machining properties. This fact is exemplified by problems that have arisen in the automotive and airplane industries, but many in other fields might be cited. As pure alunlinum and its alloys in their various commercial conditions show appreciable differences in their machining properties, it is not surprising that quite divergent solutions have been offered for the machining problems encountered. However, if the fundamental requirements of the most suitable cutting tools for these metals are understood, these machining problems lend themselves more readily to satisfactory solutions. Since the machining of free cutting brass and mild steel is understood by most persons accustomed to working these metals, it may serve our purpose better to first make a general comparison of the tools more commonly used in machining these metals with the tools most suitable for machining aluminum, then proceed to a more specific discussion of the individual tools. Comparison oF Cutting Tools Cutting tools commonly used for machining free cutting brass usually have little, if any, top and side rake; they are ground on a medium to coarse abrasive wheel and used without any cutting compound or with a cutting compound that has a paraffin base. Those ordinarily used for steel have some top and side rake, are usually ground on a medium to fine abrasive wheel, and are often used with soluble-oil cutting compounds. The proper tools for aluminum and its alloys should have appreciably more side and top rake than the tools for cutting steel; should have very keen edges obtained by grinding with fine or very fine abrasive wheels supplemented in many cases by hand stoning with an oil-stone; and should be used with suitable cutting compounds whenever possible. In many cases, tools suitable for machining aluminum and its alloys are not appreciably different from tools commonly used for cutting hardwoods. The front clearance of a tool most suitable for machining aluminum and its alloys should be about 6°, the top rake from 30" to 50°, making the total angle of the cutting edge of the tool from 35' to 55". A side

Further discussion of the paper of JAMES JOHNSTON, presented at the New York meeting, February,. 1914, and printed in Bulletin No. 85, January, 1914, pp. 107 to 133. See also Bulletin No. 91, July, 1914, pp. 1473 to 1496. THOMAS CROWE,* Victor, Colo.-The interest manifested of late in the treatment of low-grade ores, together with Mr. Clevenger's discussion of the Mill and Metallurgical Practice of the Nipissing Mining Co., prompts me to acid a few remarks relative to concentration in connection with cyanide treatment of low-grade ores. Mr. Clevenger in this discussion does not condemn concentration in this connection, but, nevertheless, the tone of his remarks would lead one to believe that his conclusions are like those of many others: that concentration is often turned to as a last resort in an attempt to improve or obtain an extraction upon an ore by the recovery and sale of the refractory portion of the ore. This, I will attempt to point out, is not always the case. Concentration in connection with cyanidation often performs an entirely different function, i.e., one of saving fine grinding. Economy being the keynote of successful treatment of low-grade ores, the problem often becomes more commercial than metallurgical, and, as there is generally a definite ratio existing between cost of operation, degree of comminution, and percentage of extraction, the grade of ore under treatment usually imposes a limit upon these factors. With many ores grinding is the most expensive single item in their treatment; therefore, the degree of comminution is very apt to be governed by the allowable cost of operation. With most ores the degree of comminution controls to a great extent the percentage of extraction. So in the treatment of low-grade ore it often becomes necessary to sacrifice extraction, through coarse grinding for the benefit of cost, in order that the greatest ultimate profit may be obtained, and it is under these conditions that it is, possible for concentration to play an important part in overcoming to some extent the effect of mesh. The precious metals occurring in an ore are usually closely associated with the metallic portion of the ore, and as this metallic portion is generally fairly well liberated from the gangue at comparatively coarse meshes, further grinding of the ore is necessary only in order that the metallic portion may be reduced sufficiently fine that the precious metal part of it may be dissolved by cyanide solutions in a reasonable length of time.

Jan 11, 1914

By E. W. Johnson, M. L. Hill

Equilibrium concentrations of hydrogen in iron were measured at H2 pressures up to 136 atm and temperatures down to 145°C. Residual hydrogen was prominent near 600°C in air-melted but not in vacuum-melted iron. The diffusible hydrogen solubility is abnormally high below 390°C, confirming the hypothesis of hydrogen trapping.' It appears that the traps for hydrogen in iron form suddenly on cooling. The estimated H2 pressure in equilibrium with 5 ppm hydrogen in steel at room temperature is less than 1000 atm. It was shown previously1 that the diffusivity of hydrogen in a-Fe below 200°C is anomalously low, a behavior attributed to the presence in the metal structure of hydrogen "traps." The energy of the trapped hydrogen was computed as 4.8 kcal Per g-atom below that of the interstitially dissolved hydrogen. The strongest confirmation of the trap hypothesis should be obtainable from measurements of the hydrogen solubility at low temperatures. such measurements have been performed and are reported in this paper. The "residual hydrogen" effect1'' must be carefully controlled if valid measurements of the solubility are to be obtained, and such an effort was made in the present work. Previous data for the solubility of hydrogen in iron have been summarized by Geller and Sun.3 Their equation for the most probable solubility at 1 atm in a-Fe above 400°C is

Jan 1, 1962