Search Documents

By J. E. Berg

THE geology of the Coeur d'Alene mining district is so familiar to every one interested in mining that I will only note as an introduction that the main producers are mines whose orebodies lie in the Revett or Burke quartzites ; that the known orebodies in the eastern part of the district all lie north of the Osburn fault; that the Prichard formation is quite generally looked upon as being unfavorable for lead deposits ; that the monzonite intrusive mass extending north from Gem to Sunset Peak, and over into Cedar Creek divide, is considered to have been the prime agent in the crea-tion of our orebodies, and that diabase dikes are a quite common feature at most of the properties with which I am familiar. Some of the exceptions to these statements may be mentioned. The Interstate-Callahan mine is considered the exception disproving the alleged relation between large ore-deposits and the Prichard formation, but this property was primarily a zinc producer, with lead secondary, though of sufficient tonnage to be a valuable product. A second interesting occurrence in the Prichard worth calling to your attention is the Jack Waite property, on Tributary Creek, north of Murray. This vein lies at a low horizon in the Prichard forma-tion, and the ore differs essentially from others in the same horizon elsewhere in that it is a clean, medium to coarsely crystalline, lead ore carrying very little zinc, about one ounce silver to ten units lead, and is accom-panied by a clean quartz gangue or vein filling. I believe that quartz was the primary mineral in the fissure, and that the lead ore was deposited in the vein as a replacement of the quartz.

Jan 7, 1927

By H. Kenyon Burch

PaQe Introduction.............................................................. 708 Plant Sites................................................................ 709 Type of Construction...................................................... 710 Mine Plant............................................................... 710 Dual Arrangement.................................................... 711 Underground Haulage............................................. 711 Tipples........................................................... 712 Underground Pockets............................................. 712 Automatic Measuring and Loading Devices......................... 712 Shafts ............................................................. 716 Ore and Spillage Skips............................................ 716 Automatic Hoists................................................. 716 Man Elevator..................................................... 717 Crushing Plant....................................................... 718 Storage Bin........................................................... 720 Sampling Plant....................................................... 720 Motors and Other Equipment.......................................... 721 Compressor Equipment................................................ 721 Concentrator............................................................. 722 600-Ton Test Mill..................................................... 722 The 15,OO0-Ton Concentrator...................................... 726 Grinding Section.................................................. 726 Floor Arrangement........................................... 726 Marcy Ball Mills............................................. 729 Performance of Crushing Machines............................ 730 Flotation Section.................................................. 780 . Flow-Sheet with Callow Flotation Cells....................... 731 Flow-Sheet with the Inspiration Flotation hfachines............. 731 Flotation Air Supply.......................................... 733 Concentrates Filter Plant.......................................... 733 Drag Classifiers................................................... 733 Tailing Settling System........................................... 735 200-Ft. Dorr Thickener ...................................... 736 General Equipment and Supplies.......................................... 737 Water Supply......................................................... 737 Power Supply......................................................... 737 Transformer Stations.................................................. 738 Shops and Railroad Facilities.......................................... 739 Conclusion................................................................ 740

Jan 1, 1917

Alexander Forsyth, Southport, Me. (communication to the Secretary): In Mr. Irving's able and interesting paper he describes minutely the appearance of the wolframite and its association with the refractory siliceous gold-ore. He also describes this gold-ore, but fails to mention the important pockets of metallic gold found in the Lead City occurrence of it. I use the term " metallic " in preference to the more usual " free," for it has been found that this gold is not easily amalgamated. Metallic gold is comparatively rare in the refractory siliceous gold-ores of the Black Hills; hence its occurrence in considerable amounts in the Lead City wolframite district deserves notice. I possess a beautiful specimen from the Harrison mine. It is a lump of drusy, granular ore, about 6 in. in diameter. The gold .is " shot" through it in large and small pin-heads; and in two specially oxidized areas, each about 11/2 in. in diameter, it is peppered full. The famous " Grantz strike," made in the Lead City wolframite locality, produced many beautiful gold specimens. This district affords an excellent example of the repeated discovery of new mineral values upon old ground. By reason of its proximity to the Homestake vein, this wolframite deposit was inevitably traversed many times by experienced geologists, mineralogists and mining engineers, who evidently must have thrown aside, with no thought of wolframite, the lumps of " black iron " lying about. I have the admission of an able geologist that, six months before the wolframite was discovered, he visited some of the very mines where it occurred, and passed it by as magnetic iron-ore. At the time of the discovery, the mineral was scattered over the gold-mine dumps in no small quantities, having been culled as worthless out of the gold-ore. It remained for

Jan 1, 1902

By L. D. Jaffe, R. K. Pitler

IT would clearly be advantageous to produce molten titanium, suitable for alloying and casting, directly from the relatively inexpensive tetra-chloride, without using a metallic reducing agent. Accordingly, a preliminary investigation has been made of the production of titanium by hydrogen reduction of the tetrachloride in an electric arc furnace. For the reaction: TiCl4(g) + 2H2(g) ? Ti(s) + 4HCl(g), Lockhart and his colleagues' have calculated equilibrium constants at 800" to 1500°K, based on tables of Brewer.' Extrapolating these data on the assumption that the heat of reaction varies linearly with temperature, and using Brewer's value for the heat of fusion, there is obtained for the reaction: TiCl4(g) + 2H2(g) ? Ti(l) + 4HCl(g) an equilibrium constant at 2100°K (100" above the melting point) Kp = (PHCl)4/pTlcl4 (Ph2)2 = 0.167 atm. If this is correct, starting with hydrogen saturated with TiC14 at 25°C, where the vapor pressure of the latter3 is 12.6 mm, and maintaining the overall pressure at 1 atm, 99 1/4 pct of the TiC14 would be reduced to Ti at equilibrium. An arc furnace designed for the melting of titanium and lined with water-cooled copper was used for the preliminary experimental check. Its inside diameter was 2 7/16 in. and height 6 in. The water-cooled electrode was tipped with 3/4 in. diam tung-sten. In the one run carried out, the furnace was charged with a starting batch of 293.35 g of scrap titanium,' analyzing 99.24 pct Ti. After the system was twice pumped out and flushed with argon to remove air, the arc was struck in argon and kept at 400 amp dc, electrode negative, for 1 min to melt the starting batch. Commercial tank hydrogen, dried by passing over silica gel and bubbled through technical grade TiC14 at room temperature, was then admitted to the furnace. The inlet tube directed this gas downward toward the arc and melt; the gas outlet was at the top of the furnace. The quantity of gas passed through was not measured accurately but is estimated to be about 50 liters per min at a few mm of mercury above atmospheric pressure. The arc was held in the H2-TiC14 mixture at 400 amp with little difficulty. After 10 min the arc burned through the copper lining above the melt, admitting water and ending the run. (This had happened frequently in straight melting runs under argon, and is not thought due to the atmosphere used.) In the furnace were found an ingot, several small pieces, and a little metallic powder, evidently formed when water entered the hot furnace. Some titanium also clung to the electrode. The portions were weighed and separately analyzed for titanium. Their total weight was 321.76 g of 94.82 pct overall purity. Much of the impurity consisted of tungsten broken off when the titanium was removed from the electrode. No detailed impurity analysis was made because the starting materials were impure and flooding the furnace introduced further contamination. Thus, the metal recovered contained 305.08 g Ti, as compared to 291.12 g in the starting batch. Titanium could not have been carried over from previous melting runs in the furnace, as the interior was sandblasted and the electrode ground clean before the run. Evidently at least 13.96 g of Ti were produced from TiCl4. Since this would require complete reduction of 430 liters of TiCl, gas at 12.6 mm of Hg, the efficiency of the process must have been rather high. Experimental work is continuing. No reason is seen why the process could not be scaled up to the size of a 30-ton steel-melting arc furnace. In a large unit there would be a large molten pool from which liquid metal could be withdrawn for alloying and casting. The problems of electrodes and power supply are similar to those arising in arc furnaces for melting titanium. Unreacted TiC14 and the HC1 in the exhaust gases could be recovered; unreacted H2 could be dried and re-used. The melt would be saturated with hydrogen, whose solubility in liquid titanium is unknown. Small amounts of hydrogen seem to have little effect on the properties of titanium.5 If the amount introduced was so large as to impair properties or cause casting difficulties, it could be reduced by holding the melt under an inert gas or by pumping on it, prior to casting. Acknowledgment The authors would like to thank I. Preble and M. Goldman for their valuable aid in the experimental work and the thermodynamic calculations, respectively. References 1R. J. Lockhart, J. J. Ward, M. J. Hussey, and J. W. Clegg: In unpublished report, "U. S. Air Force Project Rand. Titanium and Titanium Base Alloys." Battelle Memorial Institute (1949) 37-44. 2 L. Brewer et al: Chemistry and Metallurgy of Miscellaneous Materials—Thermodynamics. Ed. by L. L. Quill. pp 13-39, 60-192. (1950). McGraw-Hill Book Co. 3 K. Arii: Scientific Reports. Tohoku Imp. Univ. (1933) 22, 182. 4 R. S. Dean, J. R. Long, F. S. Wartman, and E. L. Anderson: Transactions AIME (1946) 166, 369-381; Metals Technology (Feb. 1946) TP 1961E. * R. I. Jaffee and I. E. Campbell: Transactions AIME (1949) 185, 646-654; Journal of Metals (Sept. 1949) TP 26813.

Jan 1, 1951

By Gordon M. Yocom

A PROPER consideration of the subject of this paper should include economic aspects as well as the technical phases of the metallurgy, production, and properties of the product. The metallurgical phases of the processing and properties of the product will be considered only from practical aspects and within the scope of the writer's experience with tonnage production. The Bessemer process was invented 85 years ago and became important because it put steel manufacture upon a larger and less costly basis. In America the Bessemer production has declined for many years and has not maintained its proportionate place with the rapid advances of the open hearth. The achievements in the open-hearth field were attained by the greater number of technical people attracted to that branch of the industry. The antipathy of technical students for the older and less popular Bessemer field gradually weakened the forces defending it and retarded the development of new and better methods. In Europe the economic advantage of the basic Bessemer process has not been overlooked and the tonnage usually is greater than that of the open hearth. The acid process has been the subject of renewed attention in America during the past few years and those who are more familiar with it are striving to show that the method is too valuable to abandon. A considerable tonnage of Bessemer-blown metal, in both molten and ingot forms, used in connection with the open-hearth practice makes it an important auxiliary unit to the industry. This practice aids in modifying the price level of heavy remelting scrap in addition to speeding up the open-hearth operation. The use of Bessemer steel has continued not only because of periodic economic advantages but also because of certain inherent qualities of machinability, weldability and stiffness, which are valuable for many applications. The properties of stiffness and rather high reaction to cold-work require some modification in order to meet the demands of modern methods of processing, which involve cold-reduction and cold-forming. At least one factor contributing to the stiffness of this steel is the relatively high phosphorus content of the acid product. The phosphorus content of the Thomas or basic Bessemer steel of Europe is considerably lower than the normal acid product in America. The American industry has continued the use of the acid process chiefly for the reason that the available ores are more easily adapted to this process from both metallurgical and economic standpoints. In European practice the basic process is necessary with the highly phosphoric ores available and it is sustained to some degree by the sale of the rich phosphate slag as a by-product. The basic process was used in this country at several plants many years ago, but was abandoned for economic reasons. A part of the past history of these trials is given here because the author believes it has not been published and it has some bearing on the subject of this paper. The information is authentic to the extent that

Jan 1, 1941

By H. C. George

THE Wisconsin. Zinc District, or the Upper Mississippi Lead and Zinc District as it is often called, lies in the southwestern corner of Wisconsin, in, Grant, Iowa and Lafayette Counties, and it includes adjoining parts of Illinois and Iowa. The district is about 70 miles long, north and south, and about 40 miles wide, east and west. It lies wholly within what is geologically known as the non-glaciated area of the Upper Mississippi Valley. HISTORY OF THE DISTRICT The district was first opened up as a lead producer in 1822. From this time until 1860, about 205,000 tons of cog lead (galena) and washed lead (galena) was produced from shallow crevices and openings. From 1860 to 1900, about 74,500 tons was produced, and since that time, from 5000 to 7000 tons has been produced annually. Since-1900, most of the lead concentrate produced has been as a byproduct of the zinc mines. The first zinc ores were mined about 1862. These were the carbonate ores, locally known as " drybone." Very little zinc blende was mined in the district, previous to 1875. The zinc blende ores mined from 1875 to 1900 were mostly of the high-grade, hand-cobbed, sheet-ore class, which usually contained from 45 to 60 per cent. metallic zinc. Such nines as the "Sallie Waters," ? Quinlin," "Lead Mine," "Benton Blende" and "Ida Blende," located near Benton, Wis., were mines which produced ores of this type, during this period. The mines located at Highland, the "Coker Mine" located at Livingston, Wis., and the "Opencut Mine" located at Shullsburg, Wis., were mines that were heavy zinc carbonate producers, previous to 1900.

Jan 12, 1917

By George B. Clark

The "Munroe effect" of shaped explosive charges was discovered by Charles E. Munroe more than 50 years ago (in 1888), but it was not until World War II that it was put to any practical use. Both Allied and Axis armies used the principle effectively in bazooka projectiles, artillery projectiles and in fixed shaped charges. The first two were used primarily to combat tanks and other armor and the latter to assault pillboxes and other fixed concrete emplacements. Many engineers and others who saw the military application of the jet effect of shaped charges believed application would be possible in many industrial fields where blasting is used, such as mining and quarrying. Some work has already been done on the problem of making shaped charges applicable to mining operations. Experimentation conducted at the National Tunnel and Mines1 was directed primarily along the lines of use of shaped charges for secondary blasting in connection with long-hole stoping methods. Experimentation initiated earlier and conducted by the author2 at the University of Utah on a more scientific basis was directed at revealing the basic principles of the functioning of shaped charges, as well as the feasibility of using them in mining operations after the principles of their operation had been clearly defined. It was found that: (I) a given design of charge required an optimum standoff to make it most effective, either in penetrating solid rock or steel (see Fig 3); (2) for a given design of charge there exists an optimum ratio of charge diameter to charge height above which the increase in effectiveness of the charge decreases rapidly (see Figs 4 and 5); (3) partial confinenlent has the effect of making charge performance much more consistent; (4) the higher power and higher velocity explosives tested are much more effective than relatively low-strength explosives; and (5) shaped charges may be adaptable to mining operations in secondary breakage and drilling blasting holes. Fig I is a diagrammatic sketch of the action of a shaped charge for two types of cavities, while Fig 2 shows the approximate manner in which the jets are believed to be formed when an explosive wave encounters the cavity, approaching it from the top. The experimentation already completed has laid the foundation for further research in the study of shaped charges. Standoff effects, effect of the strength of explosives and other features have been fairly well established. Such elements in the design of shaped charges as (I) geometry of cavity liners, (2) relative horizontal dimensions of explosive column, (3) effect of various metals and alloys in cavity liners, (4) percentage studies of jet energies, and

Jan 1, 1949

By I. N. Knap

Discussion of the paper of HOWARD R. HUGHES, presented at the Now York meeting, February, 1915, and printed in Bulletin No. 99, March, 1915, pp. 629 to 635. I. N. KNAPP, Ardmore, Pa.-The claims made in the paper for the Sharp & Hughes cone bit are modest. I have used it with satisfactory results. It is a wonder for eating through hard, brittle rock; it will drill through iron pyrites that the fish-tail bit cannot enter. Soft ground is apt to contain concretions that are much harder than the containing ground. ?We have at times in drilling with a fish-tail bit thought the hole was partly in such hard material and partly in soft, thus making a difficult place to drill past in the ordinary way. By changing to a Sharp & Hughes cone bit such obstructions were easily overcome. This cone bit has greatly widened the range of work that may now be profitably accomplished by the hydraulic rotary method of drilling. It is not, however, adapted to drill soft or sticky ground, the old fish-tail bit being better for such purposes. The fish-tail bit usually scrapes its way through the material drilled, but not always. I believe at times it cuts and chips in soft friable rock. That is, the bit seems to bite into the rock, and when sufficient torsion is put on the drill stem it breaks its hold and jumps around and chips the rock from the bottom of the hole, like a stone cutter's chisel, and then takes another hold. This condition occurs only in friable material when the bit is sharp and the feed properly controlled. The Sharp & Hughes cone bit is a most valuable -tool for the rotary driller.

Jan 5, 1915

By William R. Webster

In view of the great interest now taken in the tests of castiron and details of foundry practice, with the number of investigators at work, and recent improvements in the methods of research, it would seem that the time is ripe to attempt the solution of some of the many problems with which iron founders have to contend. Recent papers and discussions on these subjects* have opened up s large field for investigation, and have emphasized the importance of many considerations generally overlooked. With the view of promoting a comprehensive and systematic discussion, I have attempted to tabulate, in conveilient form, some of the most important points for investigation, on the general plan suggested, with such good results, by our former President, H. M. Howe, for the discussion on the Physics of Steel, at the Virginia Beach meeting, last year. This table can, no doubt, be modified or enlarged to advantage, and put in shape to serve as a guide or reminder to all who are interested in this line of work. Suggested Lines for Discussion and Investigation. I.—Correspondence between chemical composition and melting point, fluidity, shrinkage, fracture, chill, micro-structure, and other physical properties. II.—Influence of: I. Cupola mixture, use of steel and other scrap, oxidized or clean material, 2. Manner of melting, flux, etc., 3. Casting temperature, A. Fracture. 4. Manner of handling melted metal and B. Micro-structure. method of casting, C. Physical properties. 5. Size and form of casting, D. Shrinkage. 6. Kind of mould, green sand (under dif- on 1 E. Chill. ferent conditions of ramming, amount F. Residual stress. of moisture, and skin-dried), dry sand, G. Condition and quan loam, and chills, tity of carbon and 7. Rate and mode of cooling castings, other elements. 8. Manner and temperature of heating for annealing, 9. Additions of nickel or aluminum,

Jan 1, 1896

By Henry M. Howe

In my original paper, Piping and Segregation in Steel Ingots, I pointed out1 among other things that, in view of the slighter stretching (virtual expansion) of the crust, and greater opportunity for sagging, there should be less piping in broad than in narrow ingots, and less in slowly-cooled ingots, e.g., those cast in pre-heated sand molds, than in those which cool quickly, e.g., those cast in iron molds. A. A. Stevenson said that neither of these predictions agreed with his own experience. In particular, in a picture which he showed of a wide and of a narrow ingot cast from the same ladleful of steel: the wide ingot had certainly piped much more deeply than the narrow one. At the time I did not see the explanation of these discrepancies, but further reflection makes it evident. One of the most important elements in determining the depth of the pipe is the degree of " top-lag," that is, the degree to which the solidification of the top of the ingot lags behind that of the bottom. Through this lagging the steel of the upper part of the ingot is able to run down and fill the pipe below as fast as it forms. To the importance of this lagging I called attention in my original paper.' Sand us. Iron Molds.—If we compare two like ingots, one cast in an iron and the other in a sand mold, we see that the top-lag is much greater in the former than in the latter, because in the former the lower part of the ingot is cooling off fast while the metal is running into the upper part. It is perhaps easier to look at this as a case of the solidification of the hot-

Jan 1, 1910

By J. W. Freeman, R. F. Decker

A microstructural investigation was pursued to establish the mechanism of the pronounced benefits of traces of boron and zirconium on creep properties of a 55 Ni-20 Cr-15 (20-4 MO-3 Ti-3 A1 alloy at 1600°F. The mechanism of improvement of creep properties was found to be a pronounced stabilizing effect of traces of boron and zirconium on the grain boundaries of the alloy. The alloy with low boron and zirconium was subject to rapzd agglomeration of M23 C6 and in the grain boundaries, followed by depletion of y ' and intergranular microcracking at the grain boundaries transverse to applied stress. Brittle fracture then occurred by linking of microcracks. However, additions of zirconium, boron, and boron plus zirconium decreased this tendency in that order, allowing longer creep exposure and higher creep defor.mations before fracture occurred. VERY little information has been published describing the mechanism by which trace amounts of boron or zirconium improve the creep properties of complex nickel-base heat-resistant alloys, although the effect is now well recognized.1-4 Because the phenomenon is so important to properties and the effects are so striking, a study was made of the mechanism in a 55 Ni-20 Cr-15 Co-4 Mo-3 Ti-3 A1 alloy. It was believed that such a mechanistic approach would increase knowledge in theory of alloying and give a more basic understanding of alloy design to resist creep. The basic premise of the study was that boron or zirconium would alter the microstructural characteristics controlling creep and fracture to the extent that the effects could be identified by light and electron microscopy and by electron diffraction techniques. Characteristic of the microstructure of the Ti + Al-bearing nickel-base alloys is the dispersed precipitation of the intermetallic compound Ni,(Al, Ti), the ? ' phase, which is generally con- sidered to be the major source of high creep resistance.5-7 In addition, carbide phases have been identified8-10 and these can alter creep properties markedly.11 Since both the ?' and carbide transformations have been found to control properties, careful attention was paid to the effect of boron and zirconium on these transformations.

Jan 1, 1961

By M. E. Fine, A. A. Hendrickson

The critical resolved shear stress and the strain rate dependence of the .flow stress are reported for Ag base A1 single crystals up to 6 at. pct A1 over a temperature ralzge of 4.1° to 470°K. At room temperature the solid solution strengthening is attributed brinciballv to an increase in the dislocation density on alloying. At 42°K the alloys are relatively stronger because the dislocations widen on alloying and are more difficult to cut. In a previous paper, the authors reported the characteristics of strain aging in Ag base A1 alloys.' The variation of the magnitude of the strain-aging yield drops on aging time, aluminum content, and testing temperature strongly indicated that the phenomenon is due to the Suzuki mechanism. In the present paper, the critical resolved shear stress (CRSS) and the strain rate dependence of the flow stress are reported for Ag base A1 single crystals as functions of testing temperature (4.2" to 470") and A1 content (0 to 6 at. pct). Observations on the substructure and measurements of the effect of crystal growth rate are also given. The experimental re- sults appear explainable considering that aluminum additions increase the dislocation density and dislocation width. EXPERIMENTAL METHOD The methods of specimen preparation and tensile testing were described previously.' Briefly, single crystals were grown from the melt in a vacuum (1 x lom5 mm Hg), shaped into tensile samples by a combination of abrading and acid etching, annealed at 850°C in a vacuum (1 x 10" mm &Z) for several days, and furnace cooled to 200'. The testing was done on a model TM Instron using friction grips and a strain rate of about 5 x 106 per sec unless otherwise noted. The various testing temperatures were obtained by immersing the specimens in the following media: 1) 4.2': liquid helium using the apparatus of G. Byrne;' 2) 77°K: liquid nitrogen; 3) 200"K: dry ice and acetone; 4) 415' K: ethylene glycol; 5) 460' \ to 480' : molten Stanalax. In the determination of the CRSS above 296' K, a ratio method was used; the crystals were strained initially at the higher temperature, 0.1 pct shear strain, and then tested at 296' . The ratio of the flow stress between the two temperatures was then multiplied by the average CRSS at 296' K to obtain the value of the CRSS at the high temperature. (The test at 296' showed a yield point resulting from strain aging; the flow stress at 296' K was taken as the lower yield stress.) The ratio method, we believe, is more accurate than using different crystals since

Jan 1, 1962

By R. E. Somers

Discussion of the paper of R. E. SOMERS, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 101, May, 1915, pp. 957 to 996. A. C. LAWSON, Berkeley, Cal.-One point to which Mr. Graton (in summarizing the paper for us) called attention is that the author had not explained why some copper was fixed in the zone of oxidation. I recollect very well puzzling over that question at Ely, Nev., some years ago. Mr. Sales, in his paper on Butte,1 suggests the explanation. It is clue according to him to the paucity of pyrite in the primary ore. Where there is abundant pyrite sufficient sulphuric acid is formed by oxidation to take all the copper into solution and carry it to lower levels; but where the pyrite is scant so that insufficient sulphuric acid is formed, some of the copper is carbonated and so fixed in the gossan. The hypothesis, or some modification of it, as for example the combination of the sulphuric acid with lime, would appear to explain satisfactorily the fixation of the copper in the gossan as carbonate. I have, however, had no occasion in recent years to study the phenomenon. L. C. GRATON, Cambridge, Mass.-As I remember, the rocks in which the chrysocolla occurs in the Burro Mountains are both silicified and kaolinized. It seems probable that in surroundings deficient in carbon dioxide, complete oxidation of chalcocite may yield chrysocolla up to a maximum of half the copper in the chalcocite; while in rocks, like garnet contact zones and certain easily decomposable porphyries, surface decomposition appears often to yield silica in the necessary form to convert the copper of primary sulphides into chrysocolla immediately and directly upon oxidation.

Jan 12, 1915

By E. H. Kelton, R. D. Grissinger

E. E. Schumacher.*—DO YOU control the humidity in your test room? What effect does the environment have on your results? E. H. Kelton.—We do not attempt to control the humidity. As a matter of fact, the humidity in the beam tests that were conducted in a constant-temperature room varied widely and, as far as we know, there is no effect. The tension tests were conducted largely in an oil bath. I suppose there would be an effect in highly corrosive atmospheres, sufficiently corrosive to notch the specimen; otherwise, I would say none. E. A. Anderson.*—The effect of the humidity on the corrosion of zinc does not become important until the relative humidity is 70 per cent. At that point the corrosion products are capable of absorbing moisture and the corrosion rate increases. Below that point corrosion is almost imperceptible. This does not take into account any effect due to stress. That may be important. E. E. Schumacher.—Recently 1 have become very conscious of the enormous effect that surface films can exert on the physical properties of certain alloys. Shortly, we are publishing an article in which it will be shown that the fatigue endurance of some lead alloys can be changed markedly by merely changing the type of film placed on their surfaces. Changes as great as tenfold were observed. These findings make me wonder whether in your creep test you might not obtain quite variable results, depending upon the type of liquid medium used to immerse your specimens. Did you use more than one type of oil and, if you did, what were your results? E. H. Kelton.—I think we have used no more than three different oils, and we could not see any difference in effect.

Jan 1, 1945

By Jan D. Miller

Under the name given to this column, I almost feel obliged to write about some aspect of grinding, but I have decided instead to comment on the future of chemical processing. In recent years, I have seen a tremendous interest in extractive metallurgy develop among undergraduate and graduate students at the University of Utah. For example, of the 12 graduating seniors this year, over half seem to prefer extractive metallurgy to physical metallurgy. In particular, they seem to be most interested in hydrometallurgy, or chemical processing, obtaining industrial exposure to the phenomena they study via part-time employment at the Kennecott Research Center and the USBM Metallurgical Center in Salt Lake City. The stimulus has been generated by society itself. Many students are dedicated to the proposition that new technology can circumvent the destruction of our environment, a concept which provides considerable motivation. At the governmental level, the recent concern for the quality of our environment has created action in the area of chemical processing both through imposition of stringent air and water quality standards, and through increased funding for technological research in this area. The National Academy of Sciences (NAS) gave impetus to this movement when it pointed up the need for development and support of such disciplines as extractive metallurgy, particularly chemical processing, in a recent report on Mineral Science and Technology. The recommendations in the NAS report have prompted governmental action on many fronts, including the Bureau of Mines, and have also given rise to direct legislation in the form of two bills -H. R. 3492 and S. 635- presently before Congress to a mineral engineering education. The report recommends that chemical processing technology (more generally extractive metallurgy) be developed by both new engineering techniques and unconventional chemical techniques such as application of the chemistry of nonaqueous liquids to mineral systems.

Jan 1, 1971

By H. J. Maguire

Those familiar with mill-practice understand the work required of an average bucket-elevator, but I wish to call special attention to the wear on the buckets. I have been studying in what manner the life and service of the bucket might be improved, and I feel that an adjustable lip, attachable to each bucket without the aid of rivets, will be of material advantage. For illustration, consider the feed-elevator of a typical mill in the Cæur d'Alene district. The ore is carried by water in a launder from the feed-rolls and dumped in the " boot" of the elevator, directly in front of the ascending bucket. Middlings from the return-rolls are similarly handled. Under this condition the bucket not only carries the ore, but also picks it up, and this latter requirement determines the life and service of the bucket. It might be said that it would be better practice to convey the feed to the elevator and dump it directly into the bucket, but at one mill at which this plan mas tried the results were disappointing and the rubber belt was badly worn. The wear of the bucket is confined to the lip and the corners which have to pick up the material. When the lip on a corner of a '7- by 12-in. malleable cast-iron bucket is worn down about 3 in., the bucket is of no further value as a carrier and has to be replaced. The worn bucket, containing about three-quarters by weight of the metal of the original bucket, has a scrap value of about 10 per cent. of that of a new bucket. To the cost of the bucket, however, should be added the time-

Jan 1, 1913

By Renato G. Bautista, Theodore D. Tiemann

A kinetic study of the hydrogen reduction of taconite from the Wisconsin Gogebic range was made over the temperature range from 500° to 1000°C on eleven size fractions from 4 to 150 mesh. Two stages of reduction were observed, a rapid initial reaction followed by a slower reaction presumably taking place at an internal receding FexO-Fe interface. Calculated mean activation energies for the two reactions were 7800 and 14,600 cal per mole respectively. In recent years there has been an increased interest in the direct reduction of iron oxide ores to metallic iron by means of gaseous reducing agents such as hydrogen and carbon monoxide.1,2 These investigations have been motivated by the desire to develop a process that will by-pass the blast furnace in the production of steel. The majority of these processes have been developed to produce metallic iron by direct reduction from high-grade iron oxide ores.3"5 Very little work has been done on the low-grade siliceous iron oxide ores.6"8 The work reported here is directed principally towards the fundamental aspect of the reduction reactions of siliceous iron oxide ores, since the practical aspects of the gaseous reductant process were discussed previously. The ore used in the investigation was obtained originally from the United States Bureau of Mines10 trench sample of the Yale member of the Wisconsin Gogebic range iron formation. The Yale taconite has an average analysis of 28.2 pct Fe and approximately 50 pct SiO2. Chemically, these nonmagnetic taconites contain on the average about 53 pct silica and 30 pct Fe. An average analysis calculated fron the USBM10 figures for a composite of the five members (Norrie, Plymouth, Pence, Pabst, and ale) of the iron formation is given in Table I. Mineralogically, based on previous X-ray diffraction and other studies, the principal minerals are hematite (Fe2O3), geothite (Fe2O3.H2O), and quartz (SiO2). Minor amounts of iron containing silicates, siderite (FeCO3) and magnetite (FeO. Fe2O3) are present.10,11 The iron minerals and the quartz are finely disseminated requiring extremely fine grinding for liberation. For the experimental work, the ore sample was screened into a number of size fractions, the analyses and densities of which are given in Table II. EXPERIMENTAL PROCEDURE The reduction experiments were carried out in a 24 in. by 2 in. ID nichrome-wound vertical-tube furnace mounted on a stand. A 1 1/2 in. OD zirconium-oxide combustion tube was used inside the furnace to contain the atmosphere. To the top of this combustion tube was joined a pyrex ground-glass joint to which was attached a glass bulb with a small (1.0 mm) opening at the center, and with two outlets controlled with a stopcock on each side. A pyrex-glass joint with connections to three stopcock joints for introducing hydrogen, nitrogen, and mixtures of hydrogen and nitrogen gas was joined to the tapered bottom of the combustion tube. The sized ore fractions were contained in a 1 in. diameter by 1 1/2 in. 150-mesh nickel screen basket. The basket was suspended in the furnace from a balance by means of a supporting nickel wire which hung freely inside the combustion tube. The furnace temperature was controlled by a Leeds and Northrup Speedomax Type G controller, connected to a chromel-alumel thermocouple placed

Jan 1, 1962

By Mark J. Klein

An internal-friction profile induced by nitrogen in Cr-35 at. pet Re was studied as a function of nitrogen concentration and heat treatment. From these studies, the solubility of nitrogen in this alloy was deduced. The equilibrium solubility of nitrogen in chromium does not appear to be substantially changed by the addition of 35 at. pet Re to chromium. However the precipitation kinetics of nitrogen from solution are significantly decreased. IT has been found that rhenium has a beneficial effect on the low-temperature ductility of Group VI-A metals. As part of a study to investigate the mechanism of this increased ductility, it was of interest to compare the concentration of interstitials retained in solution in one of these ductile bee alloys with the concentration retained in solution in its base metal. In this regard, a study of the solubility of nitrogen in ductile Cr-35 at. pet Re was selected for this phase of the investigation because the solubility of nitrogen in the base metal, chromium, has been determined over a fairly large temperature span.1-3 In addition, nitrogen is known to have an embrittling effect on chromium,4 but does not appear to have a comparable embrittling effect on Cr-35 at. pet Re.5 The experimental method selected for this study was the measurement of internal friction. This technique allows interstitial-concentration measurements to be made in bee metals that are sensitive to small changes in the concentration of a particular interstitial, even when other interstitials are present. When subjected to a cyclic stress, interstitial atoms in solid solution give rise to an internal-friction peak whose origin is the stress-induced ordering of interstitials into preferred lat- tice sites. These internal-friction peaks signify a dissipation of elastic energy which is greatest when the period of oscillation is comparable with the relaxation time for the attainment of an equilibrium interstitial distribution. For dilute interstitial binary alloys, the height of the internal-friction peak is proportional to the concentration of interstitial atoms in solid solutions. snoek8 has shown that the internal friction, Q-1, may be expressed by the equation where A is the relaxation strength, ? is the angular frequency, and 7 is the relaxation time. The relaxation strength, A, is proportional to the concentration of interstitials taking part in the relaxation if no interaction occurs between solute atoms. Thus values of peak height, which can be determined as a function of temperature, give a measure of the relative concentration of interstitial atoms in solution at various temperatures. If equilibrium has been attained, the peak heights will be proportional to the interstitial solubilities. The constant that relates A to the interstitial concentration can be determined experimentally from peak-height measurements as a function of concentration for specimens of constant crystallographic orientation. When this has been done, Q-1 measurements can be used to determine solubilities according to the equation C - KQ-1 where C is the soluble interstitial concentration and K is a constant that can be experimentally determined. It is possible, however, that lattice imperfections may bind interstitials to certain lattice sites. Internal friction does not measure these interstitial~, but does measure interstitials which are free to move in the normal lattice sites when subjected to an applied oscillating stress. On alloying the pure metal with a substitutional

Jan 1, 1965

By M. Baeyertr

Since 1915 many papers and books have covered industrial applications of X-rays from various angles. Two of the more recent are a paper by Fink and Archer, which describes in detail the technique of radiography, and a paper by Clark2, which embraces the whole field of X-ray metallogmphy. This paper, therefore, is confined to work of the X-ray Laboratory of the Western Electric Co., which naturally divides into two categories: radiography and diffraction patterns of various types. Radiography Radiography is the field in which the application of X-rays has had most general appeal among the industries which produce or use metals and alloys. Equipment permitting the examination of heavy sections of metals less permeable than aluminum or other light alloys requires apparatus capable of generating hard X-rays over a considerable period of time. The equipment used in the work presented in this paper is practically identical with that described by Fink and Archer in their paper on radiography in industry and is easily capable of penetrating 1/8 in. of lead. Radiography is used in two major groups of problems: (1) in the development of cquipment and tools and (2) in studies of materials. So far there has been no instance in which the use of radiography for routine inspection is justified. This is partly due to the fact that the manufacture of telephone apparatus involves the production of many identical parts by standardized procedures and equipment that has had development and trial before being put on a regular production basis. It is during this stage of development of equipment and tools that radiography has been used to particular advantage.

Jan 1, 1931

By A. M. Gaudin

The study that is presented here was undertaken in order to condense information concerning comminution, and covering a great variety of conditions, into one or several rules which would be of use in the development of a systematic theory as well as in many directly practical ways. As the result of this work, the following conclusions appear justified: 1. Rocks may be classified, from the point of view of comminution, into two general classes which are (a) structurally homogeneous, and (b) structurally heterogenous. Structurally homogeneous rocks are those in which fracture takes place through grains and grain boundaries alike; heterogeneous rocks are those in which fracture passes in preference through grain boundaries. 2. If a sized product composed of structurally homogeneous rock grains is crushed, a product results in which the relation between the percentage weight of grains of various sizes and these sizes themselves follows a definite law. This is not true of structurally heterogeneous rocks. 3. Ball milling with structurally homogeneous rocks, and under certain conditions, presents exceptions to this rule. 4. In ball milling with structurally homogeneous rocks, there exists a critical ratio of size of feed to size of balls, above which the machine operates essentially by surface wear, and below which it operates essentially by breaking across the body of the particle. 5. In ball milling, with structurally homogeneous rocks, and when the size of feed grains exceeds the critical size, the particles worn off are of a substantially definite size which depends upon the ball size. 6. In the case of a typical heterogeneous rock, such as Manhattan schist, particles are crushed in such a way that there is a greater proportion of grains of the size that is the average grain-size of the rock than there would be in that range of size with a structurally homogeneous rock. This has been found to be true with all the crushers tested. 7. Different methods of crushing produce grains of different shapes. 8. The importance of sizing the — 200-mesh portion of a crushed product, in crushing-efficiency investigations, has been greatly under-

Jan 1, 1926