Search Documents

By G. S. Cole, G. F. Bolling

ThIS note accompanies a study of grain structure changes in metal ingots produced by the alteration of fluid motion.1 Although the Prandtl Number of aqueous solutions is much higher than that for metals, it is quite instructive to see the simulation of freezing, as pointed out by Jackson and coworkers.2-4 Accordingly we have observed the effects of natural thermal convection, the changes induced by a steady-state rotation in one direction, and the changes under oscillation.' Temperature measurements were made under duplicate conditions whenever the visual observations appeared interesting. A solution of 15 pct NH4C1 in water was chosen. In each case the solution was preheated to 90°C in a 4-in.-diam Pyrex beaker filled to a level of about 5-in. depth and covered to prevent convective air cooling. The beaker was then placed in a container of iced brine, suitably arranged on a rotating table for movement about its cylindrical axis. Upon immersion in the brine under static conditions, fluid flow was observed near the wall of the beaker before the onset of crystallization, which generally commenced only after the temperature fell to 51.5"C. The region of flow extended about 1 mm from the wall and could not be observed elsewhere. The measured radial temperature increased sharply within 1 cm from the wall and thus over a distance considerably greater than that observed for the flow. However, we note that this difference of approximately one order of magnitude between hydrodynamic and thermal boundary layers should be expected for aqueous solutions, in contrast to metallic liquids. Beyond this layer the temperature was isothermal at a given height and in general nearly 10°C warmer than at the wall. The overall visual observation was therefore supported quite well by temperature measurement. There was also a vertical temperature gradient of nearly 2°C per cm throughout the liquid increasing from the colder bottom; this of course could not be observed visually. Eventually crystals precipitated from solution. (It

Jan 1, 1968

By Alfred F. Beasley

The slags derived from the smelting of lead and copper ores are composed essentially of silicates. The problems arising from the smelting of these ores consequently involve the study of silicate fusions. In the absence of specific knowledge concerning the compounds occurring in slags, it has been the practice of metallurgists to treat them in terms of their total chemical composition. Slags have been classified as monosilicates, bisilicates, sesquisilicates, and subsilicates according to the relative amounts of oxygen in the acid and basic radicles of the hypothetical salt produced. While this has been a useful guide to metallurgists in computing the furnace charges, it falls far short of a basis for the scientific investigation of slags. In order to understand the nature of a slag as a whole it is necessary to learn the physical and chemical properties of the mineral compounds which go to make up that slag. The efficiency with which an ore is smelted in a furnace depends primarily on the physical properties of the compounds formed during the operation. When the melting points and fields of stability of each of the mineral compounds in slags have been established, it will be possible to determine the properties of any given slag by examining the nature and amounts of its mineral constituents. Earlier Investigations In 1884 and succeeding years an extensive survey of lead and copper furnace slags was made in Europe by Vogt, and a large part of the present knowledge of the subject is due to his publications.' Vogt's interest in artificial fusions was directed primarily towards the explanation of problems in igneous and economic geology and his subsequent works have been confined wholly to that subject.

Jan 1, 1930

By A. W. Gauger

Coal as mined contains varying quantities of inorganic components (mineral matter) which, on combustion, produce the residue known as ash. It has long been realized that the weight of this residue does not equal the weight of the mineral matter originally in the coal, because of the chemical changes that take place during the ashing process. Moreover, the ordinary ash analysis presents the ash as a mixture of oxides with little or no clue to the identity of the mineral species originally present in the coal. It is only for pyritic sulfur that an attempt is made to determine a mineral component. So far as the authors are aware, there are practically no experimental data in the literature as to the percentages of the different mineral species present in coal. The oft-quoted table of Marson and Cobb1 cannot rightly be considered as data, since the authors merely state that the table "shows the probable forms in which these ash constituents exist in coal." In view of the attempts to calculate analyses and determinations of the calorific equivalent of coal to the mineral-matter-free basis, as well as the importance of the mineral species in clinkering, combustion and coking, it seems strange that so few data are available on this phase of coal technology. For example, numerous empirical corrections for use in the scientific classification of coal have been suggested to compensate for the losses from the mineral matter during ignition of the coal to ash. These include multiplication of the ash percentage by various factors such as l 1/10 and 156, the use of the Parr unit coal formula (1.08 A + 22/40 S, where S = total sulfur) as well as certain modifications of the Parr formula that attempt to correct for the organic sulfur present in the coal. Although many experiments have been made to determine the loss on ignition of the clays associated with the coal measures and correction

Jan 1, 1934

By R. Simon

Maurer's review1 summarizes quite thoroughly the various theoretical developments and experimental findings that contribute to the knowledge of rock mechanics in drilling. This discussion supplements Maurer's paper by including generalities that either have been incompletely treated in his review, or formulated from new considerations by the discussant and from hitherto unpublished experimental data. These generalities are associated with the observation that all mechanical methods of rock drilling essentially comprise a sequence of indexed, concentrated loadings on the bottom of the hole being drilled. A concentrated loading is defined as a mechanical loading by a tool that contacts at any one time only a small fraction of the surface of the body being worked and penetrates only a small fraction of the body thickness. The surface in this application is the bottom of the hole. The deformation of ductile material by concentrated loading has received considerable attention because of the importance of indentation tests for measuring hardness of metals. Some of the generalities involved in concentrated loadings on ductile materials apply also to concentrated loadings on more brittle materials such as rock. Among these generalities is the applicability of similitude considerations to scaling laws and to force-displacement and energy-volume characteristics for tools of various shapes, as summarized by Tabor.2 Vork on the flow and fracture behaviors of glass loaded with pyramidal and spherical indenters is reviewed by Douglas.3 Maurer refers to the work of Evans and Murrell on wedge loadings on coal and on mixtures of pitch and sand. It is evident from Maurer's paper that a considerable portion of the studies of rock mechanics in drilling, such as crater formation experiments, has involved concentrated loadings on rock.

Jan 1, 1967

By J. H. East, E. R. Maize

INTRODUCTION PROBABLY no other type of equipment is now being introduced into American underground mines about which less is known and about which there is more misinformation than the Diesel mine locomotive. Any equipment installed underground brings with it hazards that were not present before, and it is the purpose of this paper to show that Diesel-powered equipment can be used with safety in underground mining if certain feasible but very important precautions are taken. Diesel locomotives are not new in underground mining, since they have been used successfully in European mines for at least 19 years, but their use in American mines is exceedingly limited; so far as is known, only five Diesel mine locomotives are operating at present in United States mines. Diesel locomotives were permitted underground in Great Britain for the first time in 1939, and the rapid increase in the number in use in those mines, testifies to their safety and efficiency. More than 1300 Diesel mine locomotives are in use in European mines, according to the latest statistics; these locomotives are employed in coal, iron, lead-zinc and mercury mines. So far as is known, the Diesel mine locomotive has not yet caused an explosion or mine fire, and has not been the cause of any fatalities from toxic gases in the mines in which it has been used. ADJUSTMENTS OF DIESEL ENGINES FOR UNDERGROUND USE A Diesel engine adjusted to work in an underground mine should not be confused with the same engine adjusted for use outside the mine. Adjustment of the air:fuel ratio for engines that are used on the surface is intended to give the maximum fuel economy, and little or no attention is given to the chemical composition of the exhaust gas produced. Many such engines are poorly adjusted and perhaps poorly maintained, with the result that the engine emits smoke in quantity as well as the disagreeable odor familiarly associated with Diesel engines. The air:fuel ratio in the case of Diesel engines operated on the surface is generally around 15:1; that is, 15 lb of air to burn 1 lb of fuel. Diesel engines adjusted to work underground usually have an air:fuel ratio of about 20:I, as at this ratio the minimum quantity of toxic gases is given off in the engine exhaust. Diesel engines operated underground must be maintained in better condition than similar engines used on the surface; otherwise, the smoke emitted in the exhaust becomes objectionable if not unendurable. Practically normal air is required for safe operation of Diesel engines underground or in confined places; failure to provide virtually normal air for Diesel engine operation is almost certain to result in trouble. Bureau of Mines engineers have determined that the air in which a Diesel operates in confined places should contain less than 1/2 pct of carbon dioxide and at least 20 pct of

Jan 1, 1947

By B. C. Craft

The principal events in the oil and gas operations for Louisiana during 1933 have been the rapid development of the Converse field in Sabine Parish, the discovery of three new salt domes, one in North Louisiana and two in South Louisiana, increased development in the Iowa field on the Calcasieu-Jefferson Davis Parish line, and extensive geophysical operations over a wide territory. Other miscellaneous events worthy of mention are the continued leasing of prospective oil lands over a wide area, extension of production at the East Hackberry field, Cameron Parish, discovery of deep sands at Caillou Island, Terrebonne Parish, and the completion of several important wildcats. Despite proration, oil production showed a substantial increase during 1933. The total output for this area was 25,599,802 bbl. as compared with 22,507,387 bbl. during 1932. North Louisiana There were 111 oil wells and 47 gas wells completed in North Louisiana during 1933 as compared with 109 oil wells and 33 gas wells during 1932. North Louisiana oil production decreased approximately 692,625 bbl. in 1933 from its 1932 figure. The normal decline in the old fields was partly offset by increased production at the Zwolle and Converse fields in Sabine Parish. Acid treatment of wells in the Zwolle, Converse and Monroe fields was highly successful. The method of application has been described by H. K. Shearer, Geologist, Pelican Natural Gas Co., as fo1lows:l With tubing in the hole and standing valve removed, the casing is filled with oil to the surface. The limestone solvent is pumped in through the tubing, at the same time bleeding off enough oil from the casinghead to equal the volume contained in the tubing plus the volume of open hole to be treated. The amount of solvent used in most of the wells treated was 1000 gal., which is enough to dissolve about 11 cu. ft. of chalk or limestone. After the computed amount of oil is bled off, the casinghead is closed and the remainder of the solvent is pumped in at whatever pressure is necessary to force it into the oil-producing horizon. The solvent is followed up with enough oil to

Jan 1, 1934

By William B. Senseman

FoR reasons well known to mining engineers, wet grinding is quite universal in plants having to do with the extraction of metallic values from crude ores. In the processing of the nonmetallic and industrial minerals, dry grinding is the more common method. The crude materials usually contain less moisture than is required for wet grinding and the products usually are marketed in dry form; most of them as powders. To grind wet, therefore, would entail the addition of water and an expense for drying the product, which is not justified. Furthermore, the material would be a dried cake that would still have to be pulverized or disintegrated before use. For producing fine products, air separators have largely replaced the earlier practice of sizing with screens and bolting reels. Mills in which the air-separating feature is an integral part of the design are now commonplace. Mill designs are many and air systems have developed along various lines, but for the purpose of this discussion, only the fundamental idea need be emphasized— the idea of using air for sizing and removing pulverized material from a grinding mill. About 20 years ago, when the use of mills equipped with air separation had become common practice, heated air or gas was introduced to such a system for the removal of moisture. The purpose of this discussion is to outline the developments and trends that have followed this experiment. It is an important development, for mills equipped with air separation are now universally used for pulverizing not only nonmetallic and industrial minerals, but a great variety of other materials. All such mills are essentially the same. Dried material is pulverized, removed by an air stream, trapped in a cyclone collector, and relatively clean air from the cyclone is returned through a fan to the mill. There is no theoretical need for a vent from the system. The practical need is to vent the air that leaks into the system; and, since the cyclone is not 100 per cent efficient as a dust collector, this vented air carries some dust with it. The initial attempt at drying was made on a system like that described, by the addition of a furnace. The minus pressure within the mill draws hot gas from the furnace. Infiltration air, along with the drying gases and evaporated moisture, is vented as before. The first application was made to a mill used for pulverizing coal. The coal contained very little moisture, so very little drying effect was needed for the success of this experiment. Actually, some calculated efficiencies of over 100 per cent were obtained before due allowance was made for the conversion of mill power into useful heat. When moisture is low, the heat obtained from the conversion of milt power is an appreciable part of that required. That drying can be effected in the short time interval available in a grinding mill of this type is better understood by visual-

Jan 1, 1948

By William B. Senseman

FoR reasons well known to mining engineers, wet grinding is quite universal in plants having to do with the extraction of metallic values from crude ores. In the processing of the nonmetallic and industrial minerals, dry grinding is the more common method. The crude materials usually contain less moisture than is required for wet grinding and the products usually are marketed in dry form; most of them as powders. To grind wet, therefore, would entail the addition of water and an expense for drying the product, which is not justified. Furthermore, the material would be a dried cake that would still have to be pulverized or disintegrated before use. For producing fine products, air separators have largely replaced the earlier practice of sizing with screens and bolting reels. Mills in which the air-separating feature is an integral part of the design are now commonplace. Mill designs are many and air systems have developed along various lines, but for the purpose of this discussion, only the fundamental idea need be emphasized— the idea of using air for sizing and removing pulverized material from a grinding mill. About 20 years ago, when the use of mills equipped with air separation had become common practice, heated air or gas was introduced to such a system for the removal of moisture. The purpose of this discussion is to outline the developments and trends that have followed this experiment. It is an important development, for mills equipped with air separation are now universally used for pulverizing not only nonmetallic and industrial minerals, but a great variety of other materials. All such mills are essentially the same. Dried material is pulverized, removed by an air stream, trapped in a cyclone collector, and relatively clean air from the cyclone is returned through a fan to the mill. There is no theoretical need for a vent from the system. The practical need is to vent the air that leaks into the system; and, since the cyclone is not 100 per cent efficient as a dust collector, this vented air carries some dust with it. The initial attempt at drying was made on a system like that described, by the addition of a furnace. The minus pressure within the mill draws hot gas from the furnace. Infiltration air, along with the drying gases and evaporated moisture, is vented as before. The first application was made to a mill used for pulverizing coal. The coal contained very little moisture, so very little drying effect was needed for the success of this experiment. Actually, some calculated efficiencies of over 100 per cent were obtained before due allowance was made for the conversion of mill power into useful heat. When moisture is low, the heat obtained from the conversion of milt power is an appreciable part of that required. That drying can be effected in the short time interval available in a grinding mill of this type is better understood by visual-

Jan 1, 1948

By B. Fitch

This paper deals with the behavior of sedimenting suspensions. More particularly, it treats, in as organized a manner as possible, the body of knowledge, theoretical or empirical, by which one predicts the behavior of miscellaneous swarms of particles in suspension. Such knowledge is necessary for precise and economical design of equipment. While the behavior of a single spherical particle settling through an infinite sea of quiescent fluid is well understood, practical sedimentation processes are almost always concerned with particles of assorted sizes, densities, and shapes, in such concentration that there is profound particle interaction. Such swarms of particles are observed to settle in any of four markedly different manners. Which one they follow is governed by particle interaction. It is determined largely by the dilution of the suspension, and the relative tendency of the particles to cohere. TYPES OF SEDIMENTATION The relationship between the different modes of sedimentation is shown paragenetically in Fig. 1. The left side of the diagram represents particles having little tendency to cohere; the right side represents particles for which interparticle cohesion is large compared to the settling force. The vertical axis represents dilution. As seen in the diagram, sedimentation is divided into three broad fields or regimes. At high dilutions there exists a regime here named 'clarification.' Particles in clarification may settle either individually, or by collecting into separated floccules. Thus there are two different possible modes of settling in the clarification regime. It is characteristic c~f this regime that there will be no clear line of demarcation between settling suspension and a supernatant. Faster particles settle out ahead of slower ones. In batch tests there develops a gradation of both particle sizes and pulp density due to progressive depletion of the largest particles from any given pulp level.

Jan 1, 1962

By Roy D. McLellan

Electrolytic production of cadmium at the Great Falls plant started in the first part of the year 1925. Prior to that time, an experimental unit had been in operation for a few months during the year 1922. At present the plant is the largest producer of cadmium, not only in the United States but in the world. Electrolytic cadmium is characterized by its very low content of impurities. The main impurities, which are lead, copper, zinc and iron, do not aggregate more than 0.05 per cent., leaving a cadmium content better than 99.95 per cent. The consumption of cadmium has increased rapidly since the war, with the growing use in the plating industry. Cadmium plating has come into prominence because of its connection with the automobile and radio industries. As a protective coating, a deposit of cadmium is superior to zinc. Cadmium is also used extensively in alloys. Important among these is the alloy with copper used in telephone and trolley wire. In proportion of 0.5 to 1.2 per cent., cadmium adds materially to the strength and wearing qualities. Practically all commercial zinc concentrates contain a small amount of cadmium. In the electrolytic zinc process, the cadmium that is dissolved in the regular leaching operation is removed from solution with metallic zinc, generally added in the form of zinc dust. This precipitate also contains the copper taken into solution and the excess of zinc dust, which is required in order to insure a complete removal of all impurities. The precipitate is treated by a separate process to recover the copper, cadmium and excess zinc. In order to make the metals more soluble and to render insoluble such impurities as iron, arsenic and antimony, the precipitate is roasted. The roasting is carried out in gas-fired McDougall furnaces, with a roasting temperature of about 700' C. The roasted residue is leached with dilute sulfuric acid, spent electrolyte from the zinc electrolyzing, containing 10 to 12 per cent. free H2S04. The leaching is done in cylindrical tanks of 30 tons capacity, agitated

Jan 1, 1930

R. H. Sweetser.—Mr. Reinartz spoke of slag containing 18 per cent FeO. I think he expressed the iron as oxide. I should like to ask at what point, in iron contents, it is usual practice to quit sending that open-hearth slag to the blast furnace? L. F. Reinartz.—NO problem is involved in disposing of open-hearth slag to our blast furnaces because, on account of the grades of iron and steel made by our company, the iron oxide in the slag is sufficiently high to make it very acceptable to the blast-furnace operator. I have been told that if the total iron oxide in the slag is under 18 to 20 per cent, it is not economical to use such slag in a blast furnace. J. T. Mackenzie,* Birmingham, A1a.—Mr. Reinartz mentioned sulfate in the limestone. I wonder if he did not use the wrong word. We always have assumed that the sulfate sulfur is practically harmless. Most limestone carries some pyrite (sulfide sulfur) which we thought was what gave the sulfur pick-up. L. F. Reinartz.—I have had no experience, personally, in the use of limestone high in sulfates. I have been told, on several occasions, by other open-hearth men, that the sulfates will be reduced and increase the sulfur content of the metal. We have never found any pyrite in our limestone. A. Hayes,† Middletown, Ohio.—I should think that sulfates would be readily reducible to sulfites, and possibly to sulfides at various distances through the slag layer, from the top down to the interface between the bath and the slag, because reducing conditions are certainly sufficiently strong next to the bath in the slag to reduce sulfates to sulfides. A. L. Feild,‡ Baltimore, Md.—What is Mr. Reinartz's theory as to the effect of silica in the slag on the iron oxide content of the metal? L. F. Reinartz.—I have no particular theory as to the effect of silica in the slag on the iron oxide content of the metal. I know from practical experience that it does have an influence on reduction of iron oxide in the metal. We know that if the silicon content of the charge, and, therefore, the silica of the slag is increased, the iron oxide in the slag will be decreased. Based on Dr. Herty's work, we assume that the iron oxide is correspondingly decreased in the metal. C. H. Herty, JR.,§ Bethlehem, Pa.—In the theory of iron oxide control, we have tackled the matter from the physical standpoint, rather than the chemical standpoint or from the slag itself, and we worked on the basis that the change in iron oxide content in a slag—that is, whether the slag increases or decreases in iron oxide—is due to the simple fact that if you put more iron oxide into the slag from the gas than you put oxygen from the slag into the metal, the slag must increase in iron oxide;

Jan 1, 1935

By C. B. Dudley

bas shown us that the railroads of this country can save several milt liohs a par by adopting uniform rail sections, and as unfortunately for him, he cannot patent his idea, it only remains for the railroads to adopt it, and to thank him for his payer. Dr. C. B. Dudley, Altoona, Pa. : 111 rising to close this interestin~ discussion, I want, in the first place, to thank every one who has contributed to it for his full and open criticism. The work tvhich has been done on steel rails, and which has been diwu&e,l here Juring thee two days, was not done to establish any pet theories, nor to make out that any person was great or any person small, but with a sincere desire to get at what is the truth in regard to the wedring capacity of steel rails. There are enormous commercial coneiderations invoIved in this question, and, as I look at the matter, the more honest criticism and fair discussion there is, the Inore likely it is that the truth will appear. Ad first I would like to say that it seems to me very little has been said here upon the main conclusion of the paper, namely, that the softer rails give the better wear. All sorts of side issues have been discussed; but this poiat, which is really the principal one at issue, has been largely ignored, aid I cannot But feel that it still remains unshaken. Witb regard to ohemists end chemical work, there has been considerable said tending to throw discredib on chemists and their work; and while I believe that there have been in the past, are now, and may be in the futnre, a good many poor chemical analyses made, X also believe that chemists are, as a rule, as honest and competent as gentlemen who belong to other professiomc. There are chemisb who are chemists, and who are not chemists. The determination of -manganese has bee* called in question. Now I think the chemist at almost every steel works in the country will tell you that, in his experience, the manganese diffe1.s in different parts of the same ingot. Mr. T. T. Morrell, chemist of the Camhria Iron Company, whom I believe to be s thoroughly competent and hone6t chemist, tells me that he has often found different amounts of manganese in different parts of the same ingot. Come with me to Altoona, and I will take you into the machine shop where steel is king cut aud shaped, and I will show you that it is often necessary to stop the lathe or planer and take a cold chisel to cut oat a hard spot, or else ntn the risk of breaking the tool. This hard spot is simply a pttrt of the syiegel which was not thoraughiy mixed with the ma

Jan 1, 1881

R. H. Sweetser.—Mr. Reinartz spoke of slag containing 18 per cent FeO. I think he expressed the iron as oxide. I should like to ask at what point, in iron contents, it is usual practice to quit sending that open-hearth slag to the blast furnace? L. F. Reinartz.—NO problem is involved in disposing of open-hearth slag to our blast furnaces because, on account of the grades of iron and steel made by our company, the iron oxide in the slag is sufficiently high to make it very acceptable to the blast-furnace operator. I have been told that if the total iron oxide in the slag is under 18 to 20 per cent, it is not economical to use such slag in a blast furnace. J. T. Mackenzie,* Birmingham, A1a.—Mr. Reinartz mentioned sulfate in the limestone. I wonder if he did not use the wrong word. We always have assumed that the sulfate sulfur is practically harmless. Most limestone carries some pyrite (sulfide sulfur) which we thought was what gave the sulfur pick-up. L. F. Reinartz.—I have had no experience, personally, in the use of limestone high in sulfates. I have been told, on several occasions, by other open-hearth men, that the sulfates will be reduced and increase the sulfur content of the metal. We have never found any pyrite in our limestone. A. Hayes,† Middletown, Ohio.—I should think that sulfates would be readily reducible to sulfites, and possibly to sulfides at various distances through the slag layer, from the top down to the interface between the bath and the slag, because reducing conditions are certainly sufficiently strong next to the bath in the slag to reduce sulfates to sulfides. A. L. Feild,‡ Baltimore, Md.—What is Mr. Reinartz's theory as to the effect of silica in the slag on the iron oxide content of the metal? L. F. Reinartz.—I have no particular theory as to the effect of silica in the slag on the iron oxide content of the metal. I know from practical experience that it does have an influence on reduction of iron oxide in the metal. We know that if the silicon content of the charge, and, therefore, the silica of the slag is increased, the iron oxide in the slag will be decreased. Based on Dr. Herty's work, we assume that the iron oxide is correspondingly decreased in the metal. C. H. Herty, JR.,§ Bethlehem, Pa.—In the theory of iron oxide control, we have tackled the matter from the physical standpoint, rather than the chemical standpoint or from the slag itself, and we worked on the basis that the change in iron oxide content in a slag—that is, whether the slag increases or decreases in iron oxide—is due to the simple fact that if you put more iron oxide into the slag from the gas than you put oxygen from the slag into the metal, the slag must increase in iron oxide;

Jan 1, 1935

By N. E. Maccallum

(Cleveland Meeting, October, 1912.) ALMOST half a century has passed since the Siemens brothers, after tedious and costly experiments, finally began the manufacture of open-hearth steel. The furnace of that time was very small, having a hearth-capacity of from 3 to 4 tons, and we can appreciate the wonderful development that has taken place in those 50 years by the knowledge that to-day furnaces of 50 times the original capacity are in operation. As the new steel process assumed importance, and furnaces began to grow in number and in size, a question arose, to which no satisfactory answer has ever been given, and that was: ?What is the safe and economical limit of the open-hearth furnace?" Various stopping-places have been suggested, and 20, 30, 40, and 50 tons have each been advocated, but all such arbitrary restrictions have been passed, and 60 tons would probably represent the average furnace, although in a few instances from 70 to 80 tons are regularly tapped into one ladle. The furnaces which are the subject of the present paper have gone far beyond even these limits, and since, in my opinion, they mark another step in the progress of open-hearth steel, they will be considered fairly and frankly, in order that those to whom the matter may be of interest may be able to judge and form their own Conclusions. Short accounts of the work of these furnaces have appeared from time to time in various technical journals, of which the following is a brief résumé. These furnaces are the property of the Phoenix Iron Co., of Phoenixville, Pa., and their distinctive and important feature is, that they charge to twice the capacity of one ladle, and tap simultaneously into two ladles, with a device for controlling the flow into either. In this way the capacity of the furnace is not limited, as formerly, but heats of any size within the capacity of two ladles may be charged.

Oct 1, 1912

By G. E. Pellissier, C. W. Mason

Tin has long been cited as offering a classic example of polymorphism, second in repute only to the allotropy of sulphul.. The notorious "tin disease," which Cohenl has studied so exhaustively in terms of the enantiotropic transformation of tetragonal white P tin to cubic gray a tin, has apparently encouraged the expectation that one or more additional polymorphic modifications might exist. The search for confirnmntion of this idea has, as might be anticipated, led to the accumulation of a body of miscellaneous evidence, much of which would probably never have been sought, or taken seriously even by its discoverers, but fur previous assumptions. The ball apparently was started rolling iii 1880 by Trechmann,2 who reported a new modification of tin (7 tin), which was brittle and found in "hard head," a highly arsenical, slaggy material produced in a certain stage of tin smelting. A mixture of two kinds of crystals was obtained from a Cornish tin furnace, and those thought to be 7 tin were studied crystallographically. The results indicated that these crystals were rhombic and of different density from the tetragonal tin prepared electrolytically by Miller. Their analysis was given as 98.7 per cent Sn, 1.3 per cent Fe, and traces of As, Sb, Bi and S. In 1881 von Foullon4 obtained similar crystals from a Bohemian tin furnace. Headden5 examined crystals similar to those of Trechmann and von Foullon and reported them to be monoclinic, but of analysis corresponding to stannous sulphide. Later, Stevanovic,~ by goniometric measurements, proved that these crystals of SnS were really rhombic. Groth7 pictures and describes both "rhombic tin" (Fig. 9, vol. 1) ant1 stannous sulphide (Fig. 84, vol. 1); their faces and angles correspond within the accuracy of measurement. Spencers in 1921 examined the above evidence critically; lie lound similar crystals from Cornish tin furnaces, proved them to be SnS, and even was able to analyze some of Trechmann's original specimens, finding high sulphur content. (Apparently Trechmann's analysis had been based on :L second lot of crystals, not described crystallographically.)

Jan 1, 1939

By G. E. Pellissier, C. W. Mason

Tin has long been cited as offering a classic example of polymorphism, second in repute only to the allotropy of sulphul.. The notorious "tin disease," which Cohenl has studied so exhaustively in terms of the enantiotropic transformation of tetragonal white P tin to cubic gray a tin, has apparently encouraged the expectation that one or more additional polymorphic modifications might exist. The search for confirnmntion of this idea has, as might be anticipated, led to the accumulation of a body of miscellaneous evidence, much of which would probably never have been sought, or taken seriously even by its discoverers, but fur previous assumptions. The ball apparently was started rolling iii 1880 by Trechmann,2 who reported a new modification of tin (7 tin), which was brittle and found in "hard head," a highly arsenical, slaggy material produced in a certain stage of tin smelting. A mixture of two kinds of crystals was obtained from a Cornish tin furnace, and those thought to be 7 tin were studied crystallographically. The results indicated that these crystals were rhombic and of different density from the tetragonal tin prepared electrolytically by Miller. Their analysis was given as 98.7 per cent Sn, 1.3 per cent Fe, and traces of As, Sb, Bi and S. In 1881 von Foullon4 obtained similar crystals from a Bohemian tin furnace. Headden5 examined crystals similar to those of Trechmann and von Foullon and reported them to be monoclinic, but of analysis corresponding to stannous sulphide. Later, Stevanovic,~ by goniometric measurements, proved that these crystals of SnS were really rhombic. Groth7 pictures and describes both "rhombic tin" (Fig. 9, vol. 1) ant1 stannous sulphide (Fig. 84, vol. 1); their faces and angles correspond within the accuracy of measurement. Spencers in 1921 examined the above evidence critically; lie lound similar crystals from Cornish tin furnaces, proved them to be SnS, and even was able to analyze some of Trechmann's original specimens, finding high sulphur content. (Apparently Trechmann's analysis had been based on :L second lot of crystals, not described crystallographically.)

Jan 1, 1939

By D. T. MacRoberts

This paper embodies the results of theoretical studies concerning gas reservoirs, especially the effect of drilling programs of various intensities upon pressure depletion and ultimate recoveries. The primary objective has been to determine the net quantity of recoverable gas that could be obtained as a result of each additional well, in comparison with the gas . that might be secured from a single well ideally placed with respect to both acreage and geological structure. No method is yet known whereby the relative merits of intensive and sparse drilling can be compared experimentally; a reservoir must either be drilled closely or developed with wide spacing, but both programs cannot be conducted simultaneously. Hence, the analytical method seems to be the only approach to the problem. While the present state of our theoretical knowledge does not offer a precise solution to the problem of gas flow in sand bodies, it takes such appropriate cognizance of the limitations of the methods used as to restrict any answer obtained to the realm of engineering accuracy. In solving the problem for the average gas field, it was found that practically the same answers resulted as to pressure distribution, regardless of the size of the drainage radius, even though the latter was assumed to vary from a few feet as a minimum to that of the entire reservoir as a maximum. Such limits represent extreme possibilities; therefore, the practical conditions that are associated with normal development programs, in which wells are placed in the center of tracts varying in size from 40 to 640 acres, will of necessity result in less extreme variations than those indicated in the tables accompanying this paper. Stated more concisely, the amount of gas unrecovered at abandonment (of the particular field used for illustrative purposes) will lie somewhere between 4.6 and 6 per cent of the total original content, no matter how intensively the field is drilled. Gas reservoirs may be divided into two general types, those in which the energy is intrinsic, and those of which the energy is extrinsic. † The first type contains energy in the form of a compressed gas, which expands

Jan 1, 1938

By H. K. Work, G. H. Enzian

In the manufacture of steel for commercial purposes, the deoxidation practice used, i.e., the method and degree of deoxidation, is an important factor affecting the structure and mechanical properties of the finished steel. Deoxidation practice exerts a pronounced influence not only on the soundness of the ingots but also on the reaction of the steel to a number of mechanical and thermal treatments. The first mentioned effect of deoxidation is more or less obvious and was first demonstrated, though perhaps not fully appreciated, by Robert Mushet when, in 1856, he added speigeleisen to low-carbon bessemer blown metal. In 1861. Bessemer patented the addition of one pound per ton of silicon to his blown metal to "cause the metal to lie quietly in the mold." The second effect of deoxidation-—that is, the effect on the properties and behavior of the steel—is, one might say, more subtle, and certainly not as well understood as the first, although in many cases it is the more important consideration. This paper is limited to a discussion of only the second effect of deoxidation and: in particular, to the effect on the strain-sensitivity of low-carbon steels. General Discussion Originally it was thought that the function of a deoxidizer was to combine with the oxygen present in the steel as iron oxide and prevent its subsequent evolution as a gas. -More recently it has been realized that a deoxidizer does more than this. Frequent reference has been made to the effect of deoxidizers on the nitrogen in the steel, and some attention has also been paid to hydrogen. As a consequence of the above situation any study of deoxidation must be concerned with the gas content of the steel and the effect of the deoxidizer on the gases involved. The term "gas content" as used here refers to gases extracted from steel during melting in vacuum rather than to elements present in steel in the gaseous state. The extracted gases, at least in the case of oxygen and nitrogen, are generally accepted to be products of decomposition of oxides, nitrides, or other more complex compounds. The manner in which deoxidation affects the gas content of steel and the significance of gases in steel have been and still are subjects of considerable speculation. No attempt will be made here to give a complete discussion of the literature on this subject but a few references will be cited for purposes of illustration. N. Hamilton1 found a correlation between the oxygen content of alloy steel and the behavior of the steel during tube piercing. Davenport, Bain, and others associated oxygen with aging properties of steel while Köster5 and a number of others6-lo made similar claims for nitrogen. Daniloff, Mehl, and Hertyll stated that "deoxidation decreases the susceptibility of steels to aging directly

Jan 1, 1945

By Arthur Notman

IN VIEW of the wide publicity given to the charges by the Couzens Committee of the United States Senate of discrimination by the Bureau of Internal Revenue in favor of the copper companies, it becomes a matter of interest to consider the basis for these charges. The point to be determined is whether they rest on a foundation of fact or are purely and simply matters of opinion. The whole question boils down to the purpose of the Tax Law as applied to mines, which is to afford the same protection to them as provided for all other taxpayers, namely: that they were to be allowed to pay back as depletion to their owners the values of their properties as they existed or were estimated to exist on May 1, 1913, free from tax. To determine these valuations it was? necessary to select from a wide range of possibilities a set of values for a number of essential factors.

Jan 1, 1925

By James G. Crawford

Correlation Of water with its reservoir zone or formation has been one of the applications of oil-field water analysis of greatest direct value to the petroleum engineer. The water in each producing zone tends to have diagnostic characteristics by which it can be distinguished from every other water above or below that zone in that immediate vicinity. Representative analyses of oil-field waters from producing oil and gas fields in the Rocky Mountain region are included, and the diagnostic characteristics are discussed briefly. It is concluded that the generally dilute nature of Rocky Mountain oilfield waters is a result of dilution by meteoric waters, and that there is no relationship between presence or absence of commercial oil and the character of water in a structure. Introduction The study of waters associated With oil and gas began more than 50 years ago and has been well recognized by operators, engineers, and geologists for about 30 years. It appears unnecessary at this time to recite the history of oil-field water analysis; suffice to say that it has proved its worth many times to the production engineer suddenly confronted with water problems in producing oil and gas wells. Chemists and geologists have studied the possible origin of these waters and as Yet the subject is unsolved in many important phases. There are both local and regional problems connected with the explanation of concentrations and character- istics peculiar to each field, each subsurface zone and each province. Criteria useful in postulating the Occurrence of oil Or gas in One province completely fail when applied to another, and data carefully prepared and analyzed from one field may be actually misleading when applied to another. Correlation of water with its reservoir zone or formation has been one of the applications of oil-field water analysis of greatest direct value to the engineer. The concentrations and characteristics of the waters are essential to the engineers and geologists making interpretations of electric logs in this region. The behavior of water under conditions of reservoir temperature and pressure is dependent to a great degree upon its concentration and characteristics, and thus important to the reservoir engineer. With the advent of secondary recovery methods in the Rocky Mountain region the characteristics and treatment of water will become increasingly important. Premises upon which Correlation Is Based A brief review of the geochemical history of oil-field waters will suffice to present the premises upon which correlations of the waters are based. Sedimentary rocks which are now stratified were first sediments in seas, lakes and streams. These sediments were filled interstitially with connate water. With burial the sediments were compressed arid consolidated, integrated and indurated into bed rock and much of the connate water was dispelled. Following the formation of bed rock the strata were sub-

Jan 1, 1949