Search Documents

By A. P. Watts

FOREWORD THE problem of concentrating the disseminated lead ore of southeast Missouri is extremely simple. The economic mineral is galena and the gangue is dolomite. The ore assays from 4 to .6 per cent. lead, 80 per cent. of which is recovered in a 70 per cent. concentrate.. The ore is crushed through 10 mm. and sized on 2 mm.; the oversize is jigged, while the undersize is tabled, and the slime treated by flotation. The district is the largest lead producer in the world, the output of metallic lead for the year 1915 being 183,906 tons. Over 20,000 tons of ore a day is being treated. The management of the different properties is progressive and always open to suggestion. The fact; however, must not be lost sight of, that the problem in the district is peculiar, as the average ore contains but 80 to 120 lb. of a metal normally selling at about 4c. per lb. The low price of the metal limits the treatment system to one of low cost. An elaborate treatment is neither logical nor advisable. An engineer first visiting the district may consider that the method of treatment could be improved

Jan 10, 1917

By Howard Evans

Moderate but substantive gains were recorded in 1972 in the minerals processing industry. In the area of mill design, a number of large plants under construction during the past two to three years were tuned up and went into production. The application of operating controls has also made some significant strides. Progress here has been made in the areas of on-stream particle size analysis, on-stream x-ray analysis, slurry transportation, tripper control, flotation reagent control and digital control of grinding circuits. The major contributions to improved equipment are coming from smaller specialized equipment makers.

Jan 2, 1973

By Arthur Bell

(San Francisco Meeting, September, 1915) . PRIOR to 1908 the oil production in the State of California, had been almost entirely a heavy fuel, oil, with a high flash point, hut changed within a-short period to a large percentage of refining oil with a low flash, by reason of the coming in of the Santa Maria field, the Midway field, and the increased production of the Fullerton field. This is clearly shown in the following tabulation of California's production: Year Barrels . Below -20° Be, Above 20° Be,, Per Cent_ Per Cent. 1905 48,307,000 90 10 1910 77,698,000 SO 20 1912 90,075,000 6o 31 1914 10:3,600,000 47 53 The bringing in of these high percentage's of light oil with their dangerous low flash and the increasing demand for the refined products necessitated the devising of some cheap and efficient means of quickly separating the lighter elements either in the field or at the main distributing points; also it became necessary to remove the excessive percentage of water which many of the light oils carried in emulsion.

Jan 9, 1915

By Frank C. Greene

The principal event in the development of oil and gas in Missouri in 1942 was the drilling of the Cities Service Oil Company's No. I Jim Cook, in the northwest corner, NW. 1/4 sec. 32, T. 65 N., R. 39 W., Atchison County, in the northwest corner of Missouri. This well, not yet completed, bailed several barrels of free oil in about 27° Baume from a sand called the Bartlesville by those in charge, at a depth of 1450 ft. The well is on a block of leases obtained after the area, which is covered by several hundred feet of glacial drift, had been prospected by core drilling. Earlier in the year the same company drilled a well on the Glen Gray farm in the southwest corner, SW. 1/4 sec. 29, T. 65 N., R. 39 w., to a depth of 2427 ft. in the Hunton lime with a rotary drill. Oil stains in this hole led to the drilling of the second well. Table i .—-Wells Drilled for Oil and Gas in Missouri in 1942 Country Number of Number of County Oil Wells Gas Wells Dry Andrew.......... Atchison.......... I Bates............ 2 6 Caldwell.......... I 3 Cass............. I Clinton........... I Holt............. I Jackson.......... I I Knox............ I Nodaway......... I Platte............ 4 4 Ray.............. 5 Sullivan.......... I Totals.......... I 7 28 Otherwise drilling in Missouri was uneventful, with a total of only 36 Completions, of which one was a very small oil well, Seven were small gas wells and 28 were dry holes. The total footage drilled was 24,7541/2 ft., of which 14,0281/2 was by cable tools and 10,726 ft. by rotary. Twelve of the dry holes were drilled into Mississip-pian or older beds. Table I gives a summary of activities by counties.

Jan 1, 1943

By Frank C. Greene

The principal event in the development of oil and gas in Missouri in 1942 was the drilling of the Cities Service Oil Company's No. I Jim Cook, in the northwest corner, NW. 1/4 sec. 32, T. 65 N., R. 39 W., Atchison County, in the northwest corner of Missouri. This well, not yet completed, bailed several barrels of free oil in about 27° Baume from a sand called the Bartlesville by those in charge, at a depth of 1450 ft. The well is on a block of leases obtained after the area, which is covered by several hundred feet of glacial drift, had been prospected by core drilling. Earlier in the year the same company drilled a well on the Glen Gray farm in the southwest corner, SW. 1/4 sec. 29, T. 65 N., R. 39 w., to a depth of 2427 ft. in the Hunton lime with a rotary drill. Oil stains in this hole led to the drilling of the second well. Table i .—-Wells Drilled for Oil and Gas in Missouri in 1942 Country Number of Number of County Oil Wells Gas Wells Dry Andrew.......... Atchison.......... I Bates............ 2 6 Caldwell.......... I 3 Cass............. I Clinton........... I Holt............. I Jackson.......... I I Knox............ I Nodaway......... I Platte............ 4 4 Ray.............. 5 Sullivan.......... I Totals.......... I 7 28 Otherwise drilling in Missouri was uneventful, with a total of only 36 Completions, of which one was a very small oil well, Seven were small gas wells and 28 were dry holes. The total footage drilled was 24,7541/2 ft., of which 14,0281/2 was by cable tools and 10,726 ft. by rotary. Twelve of the dry holes were drilled into Mississip-pian or older beds. Table I gives a summary of activities by counties.

Jan 1, 1943

By R. H. Tien

Temperature distribution as well as position of the solidified front is solved by means of "heat balance integral", for the case of freezing a slab with time-dependent surface temperature. Numerical solutions for the cases of linear variation and exponential decay for surface temperature are given. Application also includes solidification of casting. An increased interest in the heat-transfer problem involving a change of phase has been developed in recent years. Practical problems include solidification of a casting, freezing and thawing of soil, ice formation, and others. Despite the importance of the topic, a literature search reveals relatively few solutions which may be extended to practical problems. Due to mathematical complexity, which comes from the nonlinearity of governing differential equations, exact analytical solutions which have been published are limited to a few cases with simple boundary conditions. Although numerical solutions of these problems have become available after highspeed digital computers were introduced, lack of simple and general methods of programming for computation makes this approach impractical. The case of the semi-infinite slab with constant surface temperature was solved in the 19th century. In honor of Neumann, who first found an analytical solution, this kind of problem is generally referred to as the Neumann solution. As has been shown in Fig. 1, the problem to be analyzed is the freezing of a semi-infinite region (x > 0) which is initially liquid at the melting temperature with the surface (x = 0) maintained at time-dependent temperature. This analysis can be applied to the study of many casting processes where most of the heat removal is essentially unidirectional. "Heat balance integral" which has been used by Goodman1 is employed in this analysis. The concept of "heat balance integral" is to define a quantity, d(t), called the thermal layer. Beyond this thermal layer, for all practical purposes, there is no heat transfer, and the region is at the equilibrium temperature. "Heat balance integral" is obtained by integrating the conduction equation with respect to the space variable over this thermal layer d(t). Choosing some plausible temperature distribution, usually a polynomial or a finite trigonometric series in the space variable, this integral equation becomes an ordinary differential equation, with time as the independent variable, which can be solved by classical methods. The thermal layer and "heat balance integral" are equivalent, respectively, to the boundary-layer thickness and the momentum integral in hydrodynamics. A modern account of Prandtl's concept of the boundary layer and von Karman's momentum integral may be found in Ref. 2. Although the problem considered here has been limited initially to uniform melting temperature, the present method is equally applicable to the case with arbitrary temperature distribution in the liquid. STATEMENT OF THE PROBLEM The physical situation and coordinate system used in the problem to be analyzed are shown in Fig. 1. Notations used are listed in the table of nomenclature. Let us assume a semi-infinite region extending over positive x, initially at the uniform melting temperature. At the surface x = 0, a time-dependent temperature, which has a numerical value

Jan 1, 1965

By Paul D. V. Manning

MAGNESIUM is an exceedingly strategic material but the importance of its production at the time this war started was not realized. Our Government then suddenly became much alive to the need of a tremendous increase in magnesium output, and became a participator in the industry. In this paper an attempt will be made to given an over-all picture of the industry as it has been, and is being, developed. The present war is giving a great acceleration to the use of lighter metals. Development of facilities for production of great tonnages of aluminum and magnesium is bound to bring about some interesting changes in later peace times because costs will be low and production capacities high. As our knowledge of the metallurgy of magnesium alloys increases, this metal will become of vital peacetime importance and will be used in ways we do not now imagine. Household refrigerators, furniture, automobiles, even houses will all be lightened through the use of magnesium.

Jan 1, 1943

Executive Committee, Board of Directors Augustus B Kinzel, Chairman, J L Glllson, Vice-Chairman, A W Thornton, Howard C Pyle, Grover J Holt Finance Committee, Board of Directors Andrew Fletcher, Chairman, J S Vanick, Gall F Moulton Investments Gail F Moulton, '60, Chairman, Henry Krumb, '59, J Loveloy, '61, C R Dodson, ex off as Treasurer, Andrew Fletcher, ex off as Chairman, Finance Com¬mittee Endowment Andrew Fletcher, Chairman, N G Alford, H DeWitt Smith, W J Coulter, J V N Dorr, R B Gilmore, J B Haffner, O H Johnson, D H McLaughlin, J R McMillan, L F Reinartz, C E Weed, Wilfred Sykes, J R Suman Honorary Memberships H DeWitt Smith, '59, Chairman, C E Reistle, Jr, '59, Grover J Holt, '59, L F Reinartz, '59, M L Haider, '60, D H McLaughlin, '61, John M Lovejoy, '62, Augustus B Kinzel, ex off as President

Jan 1, 1958

By Richard McCaffery

WHEN we began the study of blast furnace slags we limited our work at first to a study of those slags containing only lime, alumina and silica. On our paper1 on some of the results of this first work, the solubility of sulfur in slags containing no magnesia was reported and the question of sulfur solubility and slag viscosity discussed. There has been, for a long time, a very great difference of opinion among metallurgists as to he effect of magnesia in blast furnace slags, and the literature is full if expressions of the most contrary opinions on the subject. As a result, our next publication' developed the constitution of slags considered as a four-component system, silica-alumina-lime-magnesia, and advanced an explanation of slag structure which accorded with the facts and with scientific theory. The present paper continues our study of the general subject of slags. As blast furnace slags are included in the silica-alumina-lime-magnesia system, which is a particular case of four-component solutions, we have determined that there are 22 components Table 1), which may enter into the silica-alumina-lime-magnesia system and that 10 or 12 of these components may be present in blast furnace slags which are within the ordinary ranges of composition. To cave a very definite conception of the behavior of these components in a slag, we have developed the theory of the cooling of a four-component solution from the liquid state to the solid and the conclusions that we obtained have been made use of in this paper. On account of the importance of the four oxides and 18 compounds which enter into the silica-alumina-lime-magnesia system, some method of calculating the percentages of the various compounds that are present in the slag when the percentages of the oxides are given, seemed very desirable and we develop L method later herein for doing this, and finally we give illustrations of the composition of a wide series of blast furnace slags and show some applications of these composition data.

Jan 1, 1927

By J. H. Bechtold

Tensile properties of annealed molybdenum were investigated from 1000" to—200°C. In the vicinity of room temperature a well-defined transition in tensile properties occurs. Reduction in area decreases from over 80 pct to 0 pct and, simultaneously, the yield strength increases about 60,000 psi. MOLYBDENUM, tungsten, iron, and many other metals and alloys with the body-centered cubic and hexagonal close-packed crystal structures change from ductile to brittle behavior over some relatively narrow temperature range. The temperature at which this transition in ductility occurs depends on chemical composition, microstructure, and method of testing. When fine grained, completely recrystallized molybdenum of commercial purity is tested in uniaxial tension at a slow strain rate, the transition occurs at slightly below room temperature.' Iron2 and tungsten3 tested under similar conditions become brittle at temperatures close to the boiling point of nitrogen, — 195°C and at about 200°C, respectively. A sharp change in ductility is uncommon in metals with the face-centered cubic crystal structure, however, a relatively sharp transi- tion in notched bar impact properties has been observed below room temperature in a face-centered cubic copper-antimony alloy.4 A transition from ductile to brittle behavior is usually explained by the concepts originally developed by Ludwik,5 and discussed and elaborated on by others including Orowan,6 Hollomon and Jaffe,7 and Gensamer8 In brief, there are two aspects to strength, first the resistance to flow and second the resistance to fracture. Both are functions of temperature, strain, strain rate, stress system, composition, and microstructure. With decreased test temperature the flow stress required to initiate plastic deformation increases more rapidly than the fracture strength and brittle fracture occurs at that temperature where the yield strength equals or exceeds a brittle fracture strength. This investigation was conducted to determine the effects of temperature, strain, and rate of straining on the flow and fracture strengths of molybdenum above, through, and below the ductile-to-brittle transition. Other variables were held constant during testing. This information is believed to show

Jan 1, 1954

Aalde, Kaare, (S'40) Box 827, Socorro, N. M. Aase, Glenn D., (S'40) Engr. Experiment Sta., Univ. of Utah, Salt Lake City, Utah. Abadesco, Enrique A., (S'39) Student. College of Engrg., Univ- of the Philippines, Manila, P. 1. Abbott, John L., (S'40) Met. Engr., Engr. Trainee. Wright Aeronantical Corp., Paterson, N. .J. Abbott, Robert H., (S'42). Agricultural & Mech. College of Texas, College Sta., Tex. Abreu, Ovidio M., (S'38) Dept. of Geol., Compauia Cousulidada de Petroleo, Caracas, Venezuela. Acomb, Allen, (S'41) 3921 Chestnut St., New Or¬ leans, La. Adam, Howard W., (S'41) Montana School of Mines, Butte, Mont. Adams, Charles E., (S'42) Uuiv. of California, Los Angeles, Calif. Adams, Charles W., (S'39) Student, Michigan Col¬ lege of Min. & Tech., Houghton, Mich. Adams, H. Travis, (S'39) 310 South 5th St., Bur¬ bank, Calif. Adams, John W., (S'42) Univ. of Texas, Austin, Tex. Adams, Rob L., (S'40) Lt., B. 0. C. No. 12, Fort Sill, Okla. Adamson, Charles R., (S'41) Uuiv. of Utah, Salt Lake City, Utah.

Jan 1, 1942

By Henry M. Rowe

Professor Ruff's most illuminating paper' describing his extremely valuable investigation of the carbon-iron equilibrium diagram assigns definite temperatures to certain very important lines in the diagram, viz.: the eutectic temperature EB (Fig. 1) and the " near-eutectic " temperature E'B', but without indicating clearly enough the reasoning which warrants these assignments. These temperatures are of such primary importance that it is well to indicate the apparent gaps in the reasoning, in the hope that they may be filled in. In his diagram, Fig. 1, the point X and the liues B'D'lII represent the experimental results reached by Ruff and Goecke;a AB, AEB, and SE represent the liquidus, the solidus, and the solubility of the carbon in solid austenite in the absence of graphite according to Gutowsky,3 AB being also in accordance with Spiecker's data; S'E' the solubility of carbon in solid austenite in the presence of graphite according to Ruer and Iljin;5 GS the line A3 after Ooerens and Meyer; 6 and EBC the true eutectic line as inferred by Prof. Ruff from Gutowsky's data. B'D' is the carbon content found in cast-iron which had apparently saturated itself with carbon in the presence of the graphite of the enclosing graphite crucibles in which the determinations were made. From its straightiiess and its sharp inflection near 6.67 per cent. of carbon, the carbon content of

Jan 1, 1913

ALABAMA Anniston.-Bretz, J. A. Carrington, F. G. Gerber, A. B. Klugh, B. G. Semple, R. A. Ashland.-Barton, .J. Bessemer.-Abbott, C. E'. Ball, T. L. Beaver, J. J. Ferguson, V. Salmon, H. S. Sehaber, C. F. Whatley, W. J.

Jan 1, 1923

Jan 1, 1958

By Shun-ichi Satoh

The electric arc welding of cast iron has been studied by Braune Lamberton, Schimpke, Kenyon, Gale Manufacturing Co., Wedemeyer Candy, Neese, Miller, Carter, American Welding Society, Namack Lebrun, Achenbach, Jansson, Xochendorffer and others.' The write of this paper has been able to obtain a series of cast irons, from gray tc white, without using cast-iron electrodes but by coating on wrought-iron bars mixtures of carborundum (Sic) and graphite (C). In this work, he found the curious phenomenon of barium carbonate.

Jan 1, 1929

By R. B. Woodworth

In the sinking of bore holes, there are but two fundamental operations —drilling and hoisting—which determine in the main the character of drilling mechanism and structures. There are endless ramifications, however, in the execution of these fundamental operations, according to the purposes for which the bore holes are drilled, their maintenance after completion, the protection and convenience of workmen, etc. The three main lines of use for bore holes are in mineral exploration, the sinking of water and salt wells, and the exploitation of pqtroleum and natural gas. This paper has to do more especially with the last. Here again there are many divergences. Wells may be drilled by either the percussive, the hydraulic, or the abrasive method. Finally, each of these methods, as applied by drillers of diverse nationalities, has followed somewhat different lines of development. The American system of cable-tool drilling has perhaps had the widest application; the hydraulic rotary is also in extensive use; but the Canadian system, the Galician system, and the Russian free-fall system all have their points of recognized merit and are preferred by operators accustomed to their use. These differences in drilling procedure, which rest ultimately on essential variations in geological conditions, are reflected in the drilling structures as well as in the drilling mechanism. The purpose of the present paper is to record those stages in the development of the application of steel to the construction of drilling mechanism and structures with which the writer has been intimately associated, and to contribute to the history of the art of drilling other data acquired in the course of his personal investigations. It is necessarily limited by reason of space to American practice, with especial reference, therefore, to the cable-tool system and the hydraulic rotary method of drilling wells for oil and gas.

Jan 1, 1916

By F. L. Bosqui

The history of the development of gold metallurgy in South Africa is divisible into two periods: That preceding the introduction of the cyanide process on a commercial scale in 1890; and the 24 years intervening between that important event and the present time. The period between the discovery of the banket reefs of the Witwaters-rand and the year 1890 was one of phenomenally rapid progress in mining development, but of no special interest to the metallurgist, There were no strikingly original or distinctly local advances in the treatment of gold ores. Californian practice in stamp milling and amalgamation prevailed, in mills ranging in equipment between 5 and 50 stamps, operating within a wide range of efficiency, and under the trying conditions usually encountered in a new and isolated field. The somewhat incomplete records of gold output of that period show that in December, 1887, there were 20 producing companies in the Witwatersrand district, of which 10 had mills, the largest being of 20 stamps. The only official record of returns for May, 1887, was that of the Wemmer mine, whose modest achievement with a 5-stamp mill was 100 tons crushed, producing 887 oz. 3 dwt. of gold. This is interesting in view of the present-day output of this field, which in 1913 reached 8,430,998 oz. The rapid increase of production during this first period (May, 1887, to January 1891) is shown by the following summary for the year 1890:1 Total tone crushed.................................. 702,828 Number of stamps in operation....................... 1,046 Average number of tons crushed per stamp per day..... 2.36 Yield of gold, ounces................................ 494,817 Yield per ton, pennyweights.......................... 13.36 The stamp duty ranged between 11/2 and 4 tons per day, according to weight of stamp, fineness of screen, and operating skill available. The prevailing weight of stamp was about 900 lb., and the screen, 900 meshes to the square inch.

Jan 1, 1916

By A. S. Richardson

AIR conditioning, or air cooling, for the improvement of ventilation in the Butte mines has come into increasing use during the past 10 years. In part, the methods practiced have been described in previous publications of the Institute, but some improvements on earlier methods have been made and a number of new features have been developed. This paper is presented as a record of progress made, and for the sake of completeness describes all general features of the work. The need for air conditioning in the ventilation of mines in the district arises from the fact that the temperature of the ground and mine water has shown a very great increase with increase in mining depth, and has now reached a maximum of slightly over 130°F. The most difficult part of the ventilation problem is the maintenance of temperature and humidity of a satisfactory standard in the working places, especially on the lower levels. Although ordinary ventilation is adequate to maintain good conditions in most of the working places it is subject to a number of limitations at great depth. Most important among these limitations is that with increase in depth the air becomes heated before it reaches the working places, both by compression from increase in atmospheric pressure and by heat transferred to it from rock at high temperature, so that its capacity for lowering temperatures is greatly reduced before it reaches the operating zone. Increasing depth of mining also increases the distance traveled by the air in its passage through the mine, and this causes a corresponding increase in resistance to air flow, so that there is greater difficulty in maintaining even the same volume in circulation. Thus, in the face of a demand that the ventilating system have a very much greater capacity to remove heat from the mine, the tendency is for that capacity to diminish. The only evident alternatives were (I) the opening of additional air shafts to increase the volume of air in circulation, (2) an extension of the existing system that would be subject to the same limitations, or (3) the adoption of an entirely different method such as air cooling. Fortunately for an economic solution of the problem, the mean annual temperature of the surface atmosphere at Butte is about 40°F., with very low relative humidity in summer, so that there is unlimited natural cooling power at a temperature range adaptable to air-conditioning methods. METHODS Two similar methods of air conditioning are used, as necessitated by service requirements and dependent upon the equipment available. In one, which is the more important and has the greater cooling capacity, water is circulated in a closed circuit, and, alternately, first absorbs heat from warm mine air and then dissipates it in the surface atmosphere by cooling at a cooling tower. The second

Jan 1, 1941

By D. Murgue

The circulation of air in underground workings is subject to a gradual and continuous reduction of its pressure, from intake to outlet, caused by the friction between it and the more or less rough and uneven surfaces of the passages. For comparison with the flow

Jan 1, 1894

By Robert Mehl

THE purpose of this investigation was to prepare high-purity iron-carbon alloys, to determine as precisely as possible the A3(GOS), the Acm(SE), and the A1(PSK) transformation temperatures in the meta-stable iron-iron carbide system (up to 1.4 per cent C), and to study the influence of carefully controlled and constant rates of heating and cooling (1/8 to 2° C. per minute) upon the transformation temperature and upon the resulting microstructure. Apart from the general metallurgical importance attending the completion of such a task, it will be noted that highly precise transformation temperatures are of interest and importance in the thermodynamic study of this system1. Several determinations of the iron-iron carbide diagram have been made. These suffer generally from the low purity of the alloys used, and from the application of methods of investigation of low sensitivity. Attempts to compare and weight the many data available in an effort to construct as accurate a diagram as possible have, in the main, been unsuccessful. In general, the wide differences in the results of different workers, the lack of complete analytical data, the omission of important details relating to the heat-treatment of the alloys, and the meager description of the methods of investigation applied, render such a process of averaging nearly meaningless. It may be seen from the summaries by Epstein2 and Körber and Oelsen1 that variations as great as 30° C. exist in the reported data on the A3 temperatures in iron-carbon alloys. For-tunately, the A3 temperature in pure iron is now known to be 910° C. ± 1° C.3 The best recent work on iron-carbon alloys is that of Esser4 on hypoeutectoid steels and that of Sato' on both hypoeutectoid and hyper-eutectoid steels.

Jan 1, 1937