Search Documents

By M. Muskat, H. H. Evinger

Although the shooting of oil wells for the purpose of increasing production has been practiced since 1866, present-day shooting technique has been arrived at almost wholly by a process of trial and error. The difficulties attending either a theoretical analysis of the problem or an experimental attack become apparent when one actually embarks on a theoretical investigation or attempts to formulate an intelligent experimental program. The literature on the subject consists mainly of descriptions of current practice, scattered eye-witness accounts of events following the shooting of a well, and vague speculations on the mechanical processes involved. In contrast to quarry blasting, the results of oil-well shooting cannot be determined by means of visual inspection, and it is perhaps for this reason that only one attempt at what approaches a direct experimental attack has been reported in the literature.' In these experiments, charges of liquid nitroglycerin were exploded in holes drilled in a sandstone outcrop. In order to observe the character and extent of the resulting fractures, the rock was blasted away so as to expose the original shot holes. After all this had been done it was found impossible to distinguish the fracturing due to the original shots from that due to the subsequent blasting. The enlargement of the holes due to the pulverizing action of the shots was measured and an attempt was made to determine the effectiveness if sand tamping. Only five shots were made and few definite conclusions could be drawn. Some small-scale experiments to deter-mine the effect of tamping were performed by Snelling and IIalL2 Small charges (zo grams) of dynamite were detonated at the bottom of a cylindrical hole in a lead block and the resulting enlargement of the hole was taken as a measure of the effectiveness of the explosion. It was found that when the shot was tamped with a sufficient amount of sand or clay, the volume enlargement was approximately double that found when no stemming had been used. The properties of the explosives have been the subject of much study by the manufacturers, the U. S. Bureau of Mines, and various other agencies. For example, velocities of detonation for many commercial explosives are to be found in the Blasters' Handbook, issued by the Du Pont company. Many other properties are given in a treatise on the subject by Naoum.~ The shock wave that accompanies the detonation of high explosives has been studied photographically by Payman4 and others. The hydrodynamical theory of the shock wave has received much attention, and an extended theoretical treatment is given by Bateman.6 Two aspects of the well-shooting problem will be considered in this paper; namely, the fracturing of subsurface strata, and possible damage to casing. With respect to the former of these, several calculations have been made giving the stresses in the rocks surrounding the shot. In order to arrive at numerical results at all, however, it is necessary to introduce a great many simplifying

Jan 1, 1941

By D. Kramer

HASEN1 has published a phase diagram for the zirconium-nickel system. This phase diagram has been redetermined by Hayes, Roberson, and paasche2 in the range 0 to 50 at. pct Ni. Recently, Smith and Guard3 have published a tentative diagram for the

Jan 1, 1960

PORPHYRY mining in the Bisbee district in Arizona did not begin until 1923, though Bisbee had been the scene of profitable copper-mining operations since 1880, and during the interval had contributed roughly 2,000,000,000 lb. of copper to the world's supply. At that time it ranked third among the copper districts of the United States, first place for total production going to Butte, Montana, and second to the district centering around Calumet, Michigan. Bisbee's production had come from the so-called "limestone" mines operated principally by the Phelps Dodge Corporation and the Calumet & Arizona Mining Co. Each of these companies had a large smelting plant at Douglas, 25 miles southeast of Bisbee on the Mexican border. The town of Douglas owed its existence primarily to the copper mines of Bisbee, the particular location having been determined, first, by the fact that water in adequate supply could be obtained by sinking wells; and, second, by its position about equally distant from Bisbee and the mines in Sonora, Mexico, of the Moctezuma Copper Co., a Phelps Dodge subsidiary. Three partners, Martin, Reilly, and Ballard, conducted the first operations of consequence at Bisbee about 1880; and in 1881 a smelting plant consisting of two 36 in. water-jacketed blast furnaces was erected near by. The ore came from open-cut workings on the later-to-be-famous Queen orebody. The furnace charge is said to have averaged 23 per cent copper-twice as rich as the concentrates from the mills and four times as rich as the smelting ore shipped from Bisbee in recent years. As early as 1881, disputes arose among owners of various claims, and groups of claims, over the ownership of orebodies under the law of apex and extra-lateral rights. This law gives a miner the right to follow his vein downward on its dip, even

Jan 1, 1933

By C. P. Lawhon, J. P. Simpson, W. M. Evans

Recent efforts to design drilling fluids for increased drifting rates have confirmed some laboratory results of other investigators, but have also produced additional data that should be considered. These data were obtained under controlled test conditions using a microbit drilling machine. Clays and some polymers have previously been reported to cause reduction in drilling rate. Recent data have shown that under laboratory conditions, suspensions of a single day or polymer have sometimes given faster drilling rates than when water was used. Measurements have been made of clay suspensions and polymer suspensions comparing filtration (I) under API conditions, (2) while drilling with temperature of 150F and differential pressure of 1,000 psi and (3) under dynamic conditions after drilling. Some correlation between instanraneous filtration (white drilling) and drilling rate has been observed. INTRODUCTION Several papers have been presented that related drilling fluids to penetration rate. Generally, it was found that a decrease in the solids concentration resulted in significant increases in the drilling rate. Of course, this change also resulted in a decrease in the viscosity of the drilling fluid.' Conclusions from investigations by this laboratory are in agreement. Data have shown that of the simple mud measurements commonly made at the drilling rig (density, plastic viscosity. yield point, API filtrate and total solids), only the density and total solids have a significant relationship to the drilling rate in Berea sandstone when attempting to correlate a single mud property individually.' More recent drilling rate experiments have been designed to study (1) effects of individual clays and polymers on drilling rates in Berea sandstone and Lueders limestone, (2) the relationship between drilling rate and dynamic filtration as measured after drilling and (3) the relationship between drilling rate and dynamic filtration as measured during drilling. Data show that drilling rates are dependent upon type and concentration of particles, type of formation and filtration of the individual fluids while drilling. Mud pressure: pressure of drilling fluid as measured after leaving the drilling chamber (Fig. 1). This is taken to be approximately the mud pressure just past the bit and at the face of the formation. Terrastatic pressure: pressure representing weight of overburden. Formation pressure: pressure of formation fluid as measured at outlet of drilling chamber (Fig. 1). This is taken to be approximately the pressure of fluid in the interstices of the formation. Differential pressure: difference between the mud pressure and formation pressure. LABORATORY EQUIPMENT AND TESTING PROCEDURE The drilling equipment was described in two previous publications."' Main components are a drilling chamber, filter-heater, rotary drive and variable-speed circulating pump. Auxiliary pumps supply pressure boosts for the mud, terrastatic and formation pressures. All equipment is designed for 15,000 psi and 500F. Capacity of the circulating system is approximately 7 gal. The mechanical design was facilitated by moving the rock down onto the bit. Data collected with this design should not differ from that obtained by a normal design where the bit moves into the rock. Drilling fluid is pumped through 50 ft of ID pipe coiled in an oil bath, enters the rotary shaft at a right angle and is pumped through the jets on the bit (Fig. 1). Most of the drilled solids are extracted by a screen mounted in the circulating system on the suction side of the pump. Data reported in this paper were obtained by controlling these parameters: mud pressure, 5,000 psi; formation pressure, 4,000 psi; terrastatic pressure, 5,000 psi; force on bit, 1,000 Ib; formation, Berea sandstone and Lueders limestone; flow rate, 7 gal/rnin; bit, 11/4-in. diameter with two 0.078-in jets; mud temperature. 150F; and rotary speed, 60 rpm. Mud pressure was controlled at 5,000 psi, thus giving a differential pressure of 1,000 psi even though the fluid densities varied. Cores of 3%;-in. diameter and 8 in. long were selected from quarry blocks to provide some control of grain size distribution, permeability and porosity. A 2-in. section was cut off each core and a I -in. diameter plug was taken from this section. Permeability to 5 percent by weight sodium chloride solution was determined and the large cores were

By D. K. Deardorff, Earl T. Hayes

An improved technique is described for the accurate determination of melting points of metals in the temperature range 1500' to 2500°C. The improvements consist of gradient heating and refinements in cavity preparation to obtain true black-body conditions. The melting point of hafnium, as determined by this method, is set at 2222°±30°C. This is over 200°C higher than one of the values reported earlier. Discrepancies in the previously reported values for the melting point of hafnium are explained. The melting points of zirconium and titanium are found to be 1855O±15OC and 1668°±10°C, respectively. Reproducibility of results was ±3OC. PRIMARILY, this report is being made to correct a 1975o±25oC1 value for the melting point of hafnium, and to present an improved method for melting point determination. As a matter of interest, the technique was also applied to determining the melting point of zirconium and titanium. There is a wide difference in the melting point of hafnium as reported by competent investigators. DeBoer and Fast' reported a value of 2230°±500C, and later work of McPherson, as reported by Aden-stedt, placed the melting point at 1975o±25oC. Zwikker" calculated that the melting point was 2430°C. In resolving this discrepancy, improvements were made in the procedure for determining the melting points of refractory metals in the range 1500" to 2500°C. Special techniques are necessary to determine the melting point of these metals accurately. Since the metals oxidize in air above 900oC, the determinations must be carried out in an inert gas or vacuum. Also, every known refractory contaminates them to some extent. In addition, the attainment of true black-body conditions is always difficult. DeBoer and Fast actually determined the melting point of Hf-Zr as-deposited iodide process alloys and extrapolated to 100 pet Hf. McPherson employed a tungsten wire suspension similar to that described by Schramm, Gordon, and Kaufmann,1 and used hafnium metal produced by the iodide process. There was no apparent reason for the wide spread in melting points, since the quality of the metal was very good and the work was under the direction of highly competent investigators. Retracing some of this work revealed one understandable error in the case of hafnium, and led to development of an improved technique for determining melting points of reactive metals in the range 1500" to 2500°C. Material Crystal bar hafnium, zirconium, and titanium were used for this work, with analyses as shown in Table I. The hafnium was of the highest purity that has been prepared, though not as pure as the zirconium and titanium. At the instigation of the Pittsburgh Area Office of the AEC, a special lot of Hfo2 was purified, converted to the tetraflouride, and bomb-reduced with calcium, all at the Iowa State College Laboratories. This crude hafnium metal was then refined by the iodide process at the Foote Mineral Co. All specimens were cut with a Sic wheel, ground, pickled, and dried carefully before use. Procedure General Tungsten Suspension Method—In this method, a small specimen is suspended by a fine tungsten wire in a slender, induction-heated tungsten or tantalum cylinder, all under vacuum. The melting point is determined by heating the specimen slowly while observing it with an optical pyrometer focused upon a portion of the specimen that radiates as a black body. This means that there should be no reflected radiation, either from colder objects near the pyrometer or from hotter surfaces. The induction heater would be the only hotter object and, if it is slender enough, the specimen will attain the same temperature. Often a slender hole is drilled into the specimen as a source of black-body radiation. This was the general method used by McPherson in obtaining his value of 1975°C for the melting point of hafnium. In trying to repeat this work, it was found that the points of contact between the

Jan 1, 1957

By Moshe Sheinkin, Douglas E. Julin

Large tonnage operations face many problems in adequately planning ahead for future years production. In order to maintain desired levels of production, such problems as source of tonnage, man- power and equipment requirements, tailings disposal and water requirements must be anticipated. Of course, before any of these problems can be analyzed, daily tonnage requirements and its source must be determined. Looking ahead for one year or even two or three is usually not sufficient time to adequately prepare an area for production. Because of the sequence of mining and the multilevel nature of the 42,000 tpd Climax mine in Colorado long-range planning must be on a ten-year basis. By using a ten-year base, adequate time is allowed to gain access and prepare a new level for production. Usually eight years will be required for this phase of the initial mine preparation. Once production has been started on a level and access to the area is available, three years is usually sufficient to prepare a new block for production as long as it follows in the normal sequence of mining.

Jan 4, 1967

By Milton E. Wadsworth, J. Brent Hiskey

Galvanic interaction between particulate chalcopyrite (CuFeS2) and copper results in the rapid conversion of chalcopyrite to chalcocite. The effects of temperature, surface area, concentration of sulfuric acid and agitation were systematically evaluated. The kinetics were found to be controlled by a steady-state current flow controlled by the effective anodic and cathodic surface areas involved in the galvanic couple. The experimental activation energy was 11.5 and stoichiometric data and reaction products have been characterized. The overall kinetic system has been evaluated based upon an electrochemical model.

Jan 1, 1974

By G. W. Healy, W. Craft, D. C. Hilty

By means of a theoretical extension of the Cr-C temperature relation in molten chromium steels to low chromium contents and by a correlation of the ratios of chromium to iron in the slag and metal, a method has been developed for estimating the amount of metallic oxidation during the oxidizing period of a chromium steel heat. Application of this method has indicated that due to temperature limitations metallic oxidation may be excessive for very low carbon steels charged with more than a small amount of chromium. IN the melting and refining of chromium steels the oxidation of carbon to a low level is accompanied by the oxidation of chromium and iron in considerable amounts. For the subsequent recovery of chromium and associated iron from the slag, the amounts of metal oxidized must be known for efficient reduction and control of composition. Further, in order to arrive at an accurate understanding of the process, so that chromium-bearing scrap can be used effectively, information is required on the relation between composition of the charge and weight of metal oxidized to reach the desired carbon content. Crafts and Rassbach1 recently developed an empirical relation between chromium, iron, and manganese oxidized per ton of steel charged, and final carbon content and temperature. This relation did not show any dependence on amount of chromium charged. However, it was felt that such a dependence might be present, so a further analysis of the data was undertaken. Cr-C Relation at Low Chromium Levels Crafts and Rassbach's results were based on temperatures estimated from the Cr-C relation previously established experimentally by Hilty,2 and on a single temperature observation (immersion thermocouple) on a heat made at low temperature from a charge of carbon steel scrap containing only a small amount of residual chromium. The temperatures estimated from the Cr-C relation were for heats charged with chromium-bearing scrap and which contained substantial amounts of chromium (2 to 10 pct) at the end of the oxidizing period. No data, other than that from the low temperature heat just mentioned, were available for the low and intermediate chromium ranges. In order to extend the range in which temperature may be estimated, the Cr-C relation requires further consideration. The Cr-C relation, expressed as suggests that carbon is zero at zero chromium in the bath. This is obviously absurd, because as chromium approaches zero the carbon content must approach the limit established by the Fe-C-O equilibrium. It is evident, therefore, that the Cr-C relation as defined by Eq. 1 is not valid below some minimum chromium content that may vary with temperature. On the other hand, it is probable that any such limiting chromium content is less than 4 pct at 3200°F, since the experimental data from which the Cr-C relation was derived included several observations at that level with no deviation. In any event, it is apparent that further evaluation of the results presented by Crafts and Rassbach is dependent upon a means for estimating the Cr-C temperature relation in the low chromium region. From the observations of Chen and Chipman9 and thermodynamic data given in Basic Open Hearth Steelmaking,4 the following relation can be calculated for melts containing small amounts of chromium and carbon assuming a carbon monoxide pressure of 1 atm: % Cr -21,250 K' = (%C)2; logK1 == —t— +13.88 [2] Moreover, by plotting Eq. 2 for any given temperature on cartesian coordinates, it can be extrapolated graphically to the limiting carbon content at zero chromium for the specified temperature without serious complications. By means of Eq. 2 and its extrapolation, the Cr-C temperature relations originally established experi-

Jan 1, 1954

By R. A. Morse, P. M. Bridges, L. E. Wilsey, Howard N. Hall, P. L. Terwilliger

Theoretical and experimental investigations of a constant pressure gravity drainage system are reported. Experimental data are presented to show that recovery to gas breakthrough by gravity drainage is inversely proportional to rate. The gravity drainage reference rate, which is numerically equal to the so-called "maximum theoretical rate of gravity drainage" is shown to have no particular significance from a recovery standpoint. Before this rate can be used as a basis of comparison for recoveries, it is necessary that the relative permeability and capillary pressure characteristics and displacing fluid viscosities be identical for the systems compared. A method is presented by which accurate prediction of the performance of a gravity drainage system can be made. Close agreement between experimental and calculated drainage performance shows that steady state relative permeability and static capillary pressure data can be used to describe fluid displacement behavior. The very wide range of liquid recoveries before gas breakthrough which result from production rate variation alone demonstrates the importance of this factor in planning depletion of a gravity drainage reservoir. Calculated results are presented which show that little additional recovery can be expected from a high pressure gravity drainage system between the times of gas breakthrough and attainment of such high gas/liquid ratios as to make further pressure maintenance impractical. INTRODUCTION It bas been recognized for some time that gravity forces play an important part in the recovery of oil from some types of reservoirs. Field experience has shown that under certain conditions, gravity drainage can result in very high oil recov- eries. Qualitative reasoning has led most engineers to the general conclusions that: (1) Where gravity drainage is important, the reservoir pressure should be maintained by gas injection at the crest of the structure to prevent shrinkage of the oil in place and to keep a low viscosity so the oil can drain at the fastest possible rate. (2) Recovery by gravity drainage is rate sensitive. A survey of the literature indicates that while considerable work has been done on the effects of gravity in oil production problems, no satisfactory method of calculating the performance of gravity drainage reservoirs has been reported.1,2,3,4,5 In the absence of any proven method of calculating reservoir performance, the level at which pressure should be maintained and the rate of production for most efficient operation has been open to debate. The limits and general character of the recovery us rate relationships are apparent from the following: As rates of production approach zero, oil will drain by virtue of its own weight fast enough that the saturation distribution is always approximately the same as the original static capillary distribution. That is, at the gas-oil contact the liquid saturation goes from 100 per cent to a value of perhaps 10 to 30 per cent in a very short distance, so that as production continues. a relatively sharp gas-oil contact moves down-structure, leaving a very low residual oil saturation in the originally oil saturated zone. At very high rates of production, the oil that drains by virtue of its own weight is negligible and recovery will approach that of a horizontal gas drive, leaving a much higher residual oil saturation. At intermediate rates of production. recovery should be between these extreme*. Despite the lack of quantitative methods, tentative agreement had been reached on the question of optimum producing rate. It has been generally concluded that rather sharp decrease in recovery would occur at rates of production above the "maximum rate of gravity drainage" and hence this rate should not be exceeded. The "maximum rate of gravity drainage" is defined as the rate of production from a 100 per cent

Jan 1, 1951

By L. E. Wilsey, R. A. Morse, P. L. Terwilliger, Howard N. Hall, P. M. Bridges

Theoretical and experimental investigations of a constant pressure gravity drainage system are reported. Experimental data are presented to show that recovery to gas breakthrough by gravity drainage is inversely proportional to rate. The gravity drainage reference rate, which is numerically equal to the so-called "maximum theoretical rate of gravity drainage" is shown to have no particular significance from a recovery standpoint. Before this rate can be used as a basis of comparison for recoveries, it is necessary that the relative permeability and capillary pressure characteristics and displacing fluid viscosities be identical for the systems compared. A method is presented by which accurate prediction of the performance of a gravity drainage system can be made. Close agreement between experimental and calculated drainage performance shows that steady state relative permeability and static capillary pressure data can be used to describe fluid displacement behavior. The very wide range of liquid recoveries before gas breakthrough which result from production rate variation alone demonstrates the importance of this factor in planning depletion of a gravity drainage reservoir. Calculated results are presented which show that little additional recovery can be expected from a high pressure gravity drainage system between the times of gas breakthrough and attainment of such high gas/liquid ratios as to make further pressure maintenance impractical. INTRODUCTION It bas been recognized for some time that gravity forces play an important part in the recovery of oil from some types of reservoirs. Field experience has shown that under certain conditions, gravity drainage can result in very high oil recov- eries. Qualitative reasoning has led most engineers to the general conclusions that: (1) Where gravity drainage is important, the reservoir pressure should be maintained by gas injection at the crest of the structure to prevent shrinkage of the oil in place and to keep a low viscosity so the oil can drain at the fastest possible rate. (2) Recovery by gravity drainage is rate sensitive. A survey of the literature indicates that while considerable work has been done on the effects of gravity in oil production problems, no satisfactory method of calculating the performance of gravity drainage reservoirs has been reported.1,2,3,4,5 In the absence of any proven method of calculating reservoir performance, the level at which pressure should be maintained and the rate of production for most efficient operation has been open to debate. The limits and general character of the recovery us rate relationships are apparent from the following: As rates of production approach zero, oil will drain by virtue of its own weight fast enough that the saturation distribution is always approximately the same as the original static capillary distribution. That is, at the gas-oil contact the liquid saturation goes from 100 per cent to a value of perhaps 10 to 30 per cent in a very short distance, so that as production continues. a relatively sharp gas-oil contact moves down-structure, leaving a very low residual oil saturation in the originally oil saturated zone. At very high rates of production, the oil that drains by virtue of its own weight is negligible and recovery will approach that of a horizontal gas drive, leaving a much higher residual oil saturation. At intermediate rates of production. recovery should be between these extreme*. Despite the lack of quantitative methods, tentative agreement had been reached on the question of optimum producing rate. It has been generally concluded that rather sharp decrease in recovery would occur at rates of production above the "maximum rate of gravity drainage" and hence this rate should not be exceeded. The "maximum rate of gravity drainage" is defined as the rate of production from a 100 per cent

Jan 1, 1951

Jan 9, 1951

By Faustino Roel

AMONG the problems confronting the mining engineer in Mexico in recent years, labor conflicts have come to occupy s prominent place. Each day they have become more serious and frequently have caused- the ruin of companies. It is therefore necessary for the engineer to understand the Federal Labor Law, the rights and obligations of companies and of their workmen, and the reasons for conflicts; to keep in mind the expense which may be caused companies; and to endeavor to avoid difficulties as far as possible. Our labor legislation is primarily to protect the workman and the constant tendency of the tribunals, including the Supreme Court of Justice, is to support the work- man in his demands against employer$, even at times granting him more than he asks, with no limit other than the economic capacity of the company to com-

Jan 1, 1937

Jan 1, 1891

By R. W. Gurry

IN the course of a series of measurements of the rate of diffusion of carbon in austenite at about 960°C. (1760°F.) and 1110°C. (2030°F.), it became necessary to determine carbon concentration when austenite is saturated with graphite, because of indications that the hitherto accepted value of the solubility of graphite in this temperature range is too low. Specimens of carbonyl iron were saturated at temperature in a hydrogen-toluene atmosphere which was in equilibrium with graphite. The carbon content of the steel was measured either by combustion or by the loss of weight after substantially complete decarburization in an atmosphere of hydrogen saturated at room temperature with water vapor. The absence of carbide or graphite as a phase at temperature was demonstrated by microscopic examination of saturated specimens that had been drastically quenched. The mean result of concordant measurements is that gamma iron saturated with respect to graphite contains 1.39 per cent carbon at 957°C. (1755°F.) and 1.89 per cent at 1110°C. (2030°F.). These two values, plotted along with what appears from the literature to be the best value (0.69 per cent) at the iron-graphite eutectoid temperature (738°C. or 1360°F.), yield a curve that is almost linear, and which, continued upward through a short interval, leads to a limiting solubility of 1.98 per cent at the iron-graphite eutectic temperature 1135°C. (2075°F.) instead of the commonly accepted value of about 1.7 per cent. EXPERIMENTAL PROCEDURE The samples of carbonyl iron, with the exception of those for microscopic examination, were cylinders 3.8 cm. long, 0.475 cm. in diameter. They were placed in a graphite holder and suspended in a vertical furnace, the temperature of which was controlled precisely by means of the resistance of the platinum winding.1 In the empty furnace the range of temperature over a distance of 4 cm. at the heat center was 9°C. (16°F.) but at a given location the temperature remained within ±0.5°C. (0.9°F.); it was measured by inserting a platinum-rhodium couple calibrated at the melting point of palladium, 1555°C. Since the presence of the sample probably improved the uniformity of temperature, it was decided to consider the average temperature of the sample to be 3°C. lower than the maximum measured in the empty furnace with the same setting of the controller. Data were obtained in the vicinity of two temperatures, 960°C. (1760°F.) and 1110°C. (2030°F.). The samples for microscopic examination, 2.2 cm. long, 0.475 cm. in diameter, were suspended individually on pure iron wire; for these no temperature correction was applied. The carburizing gas passed into the furnace was dry, oxygen-free hydrogen saturated at room temperature with

Jan 1, 1942

By Hertha R. Freche

The diffusion of magnesium and silicon from the core into the high-purity coating of Alclad sheet is important commercially, and led to the use of a duplex product for the study of diffusion by means of spectro-graphic analysis of successive layers. It has been found that in the duplex materials the diffusion of magncsium from an undersaturated aluminum-magnesium alloy into its high-purity aluminum coating is approximately of the same order of magnitude as the diffusion of silicon from a saturated aluminum-silicon alloy into its high-purity aluminum coating. However, if magnesium and silicon are both present in the alloy in the ratio of Mg2Si, they appear to diffuse in the approximate ratio of this compound. Finally, if the alloy contains silicon in excess of the amount required by magnesium silicide, the amount of diffused silicon in the high-purity aluminum coating will also be in excess. The interdiffusion of metals in the solid state is of both scientific and technical interest, because it is helpful in the study of the alloy structure and in the solution of problems pertaining to the strength and surface condition of the fabricated product. W. C. Roberts-Austenlt carried out the first quantitative determination of the coefficient of diffusion of gold into lead. This classical experiment was followed by a series of investigations on the diffusion of metals and nonmetals in iron and steel and in nonferrous metals and alloys. Recently the diffusion of copper in coated strong aluminum alloys was investigated by A. Burkhardt2. This appeared to be the first published investigation on the diffusion of metals into aluminum. The present investigation was the direct result of a technical question in connection with alloy fabrication and is a summary of some preliminary work pertaining to the diffusion of magnesium and silicon into aluminum. The results necessarily will be subject to some variations, since this is the first attempt to evaluate the coefficients of diffusion of magnesium and silicon into aluminum according to this method of procedure. This

Jan 1, 1936

By T. R. Scott

The acid pressure leaching of zinc-lead flotation concentrates from the McArthur River deposit, Northern Territory, Australia, has been studied in a three-stage, continuous, co-current system, using titanium reactors of 6 gal capacity. The starting pulp contained 2.7 lb solids per gal of synthetic spent electrolyte and the final liquors contained 120-125 gpl Zn. Parameters investigated included temperature (95-120°C), oxygen pressure (30-100 psi), acid addition (80-130% of theoretical), and leaching time (35-65 min per stage). Technical factors studied included mixing and pumping of feed, agitation, settling and washing and control mechanisms. The chemistry of liquor impurities, of scale formation in autoclaves and of lead jarosites in residues was studied in some detail. Results indicated that 90-93% zinc recovery could be obtained with a "low- acid" process, using 113°C and 70 psig with oxygen as the favored operating conditions. Residues contained 16-18% elemental sulphur and 15% lead, together with unreacted pyrite and gangue minerals. Pelletizing of residues was impracticable, and alternative suggestions for the recovery of lead, sulphur and silver are discussed. Preliminary estimates for plant and operating costs are given and enable some comparison to be made with conventional procedures.

Jan 1, 1973

By A. W. Ambrose

THE underground losses of oil exceed by hundreds of thousands of barrels all the oil that has been lost in storage, transportation, or refining. The quantity lost is, of course, indeterminate; but when it is considered that the contents of an entire oil field have been excluded from recovery by invading waters, some idea of the amount wasted may be gained. Similarly, enormous quantities of gas have been lost underground. Conservation of the oil, therefore, should start before it is brought to the surface rather than after it is placed in storage tanks. Water is one of the most important causes for underground losses and the operator should give as serious consideration to an underground flood of water as he would to a destructive surface flood. The best insurance, of course, is to have the wells drilled in such a manner that water has no access to the productive oil and gas horizons, and on abandonment the wells should be properly plugged. The encroachment of edge water and the occurrence of water in the base of an oil sand present a very serious problem to an oil company; sooner or later these waters are bound to cause considerable damage, if they do not entirely destroy the possibilities of further production. Too often, however, a field has been considered to be in a hopeless condition, whereas wells in as bad a condition in other areas have been repaired and the life of the field appreciably lengthened. The corrections are very often suggested by technical study. Very successful results have been accomplished by detailed underground work in the California oil fields, in Cushing, Oklahoma, and in other areas.

Jan 9, 1920

By Chas Dobbel

THE Chief Consolidated properties are situated in the Tintic mining district of Utah, being included in Juab and Utah Counties, about 70 miles south of Salt Lake City. The drilling referred to in this paper has been carried on in the Chief Consolidated No. 1 mine, the Gemini mine, and the Eureka Hill mine at Eureka, the Grand Central mine, above Mammoth, and the Apex Standard mine just south of Dividend. The occurrence of ore through the district is typically in lenses on bedding or breaks, and in connecting pipes, without accurate geometrical trend so that the ratio between the total length of development in drifts and crosscuts to the square feet of ore exposed is very high. A section of one of the western channels (Fig. 1) through the Tintic district, shows, roughly, the irregularities calling for excessive development work, so typical of the Tintic mines. This irregular trend of the ore constantly calls for excessive cutting up of the whole area for offshoots and the connecting links always present.. In the planning of prospecting and development, no regular system may be laid out without overlooking some orebodies or segments of orebodies. It was with these facts in mind that Cecil Fitch, the general manager of the Chief Consolidated Mining Co., decided that some method of drilling was the more feasible way of successfully cutting up and bringing about the discovery of ore believed to exist; yet this drilling had to compete with a great. margin of cost over crosscutting, as a crosscut in the Tintic district, even though barren, brings out geologic facts that, in many cases, are worth the price of the working itself. Diamond drills met with the success that might be expected in a district that has a reputation for the wear and loss of diamonds; after 6 or 8 months, this method was discarded on account of the high costs. Simultaneously, a small churn drill outfit was set up underground but a few shifts proved its inapplicability. At the same time, the ordinary hammer drill was usd to drive prospect holes with jointed steel.

Jan 9, 1925

By E. W. Pehrson, J. W. Furness

THE five charts presented here- with are part of an original group prepared by the U. S. Bureau of Mines showing the international trade in the principal metals and metallic ores. Charts 011 anti- mony, chromite, copper, lead, manganese, mercury, nickel, tin, tungsten, and zinc were published in the February, 1936, issue of the Engineering and Mining Journal. Those shown here include bauxite, aluminum, iron ore, pig iron, and the platinum-group metals.

Jan 1, 1936

By R. Woodward Moore

A graphical method of analyzing the data obtained from shallow earth-resistivity depth tests is presented. The method is based upon empirical results and has no theoretical basis. The usual apparent resistivity-electrode spacing curve is used together with a cumulative resistivity-electrode spacing curve plotted on the same sheet. The greatly reduced scale required for plotting the cumulative values of resistivity together with the effect of the summation of the individual resistivity values serves to minimize the effect of purely local surface anomalies and inadvertent errors of measurement. The point of intersection of tangents or straight lines drawn to intersect at zones of maximum curvature in the cumulative curve indicates the depth to the underlying material. Numerous figures are presented in which data from published reports and from recent field studies are analyzed and the results compared with actual depths established by borings or with depth values obtained by the use of theoretical methods of analysis. Smoothly rounded curves of apparent resistivity such as are often obtained in the field, and which have been a serious drawback to attempts to analyze the data empirically heretofore, appear to be susceptible to rather accurate analysis by the method described. The method is best suited to analyses involving shallow two-layer formations. It has been applied successfully, however, in analyzing the data obtained from tests made over shallow three-layer formations. As with most empirical methods, its chief advantage is its simplicity and ease of application. There have been published many papers that discuss the interpretation of data obtained from earth-resistivity tests when using the four-terminal method of electrode spacing developed by Wenner.' The majority of these have dealt with theoretical analyses for two-layer and three-layer formations. Some sets of "master curves" have been presented for use in analyzing field data to determine the depth to the first and possibly the second horizon below the earth's surface. Although practically all of these theoretical methods of analysis have appeared to have particular merit and some have been used successfully in practice, they have been found to be of little value where the local conditions surrounding the test failed to conform to those assumed in the theory. In certain fields, particularly in civil engineering, relatively shallow explorations are often involved and geophysical methods of test must compete with the direct methods of exploration ordinarily used. Only when it can be demonstrated that geophysical methods of test can materially reduce the time and cost of a given exploration project will the civil engineer abandon direct methods in favor of the interpretations of geophysical exploration data. Empirical methods of analyzing earth-resistivity data have been used in many instances in the past. Such methods have been employed for a number of years by the Public Roads Administration in research work relative to the application of

Jan 1, 1946