Search Documents

By B. Habermann

Artificially consolidated sand models, representing one-quarter of a five-spot, have been developed and used to study factors aflecting misciblt. displacrmenr. Sweep efficiency at breakthrough, size of the mixing zone between two miscible liquids and per cent area contacted by drive after breakthrough were determined tor the high mobility ratios encountered in actual resvrvoirs. Quantitative relationships between the degree of viscous fingering and mobility ratio were obtained by measuring the length of the fluid interface. Scaled miscible-slug experiments, supported by field evidence reported in the literature, have shown that when the slug is followed by dry gas the process is less efficient than expected. In addition to low areal sweep efficiencies encountered for high mobility ratio displacements, the effectiveness of a miscible slug is greatly reduced. This is caused by an accelerated growth of the mixing zone between the driving and the displacing fluids. INTRODUCTION Considerable interest in miscible displacement as a secondary recovery process has been shown by the oil industry in recent years. In addition to extensive laboratory investigations, numerous field operations have been initiated so that 39 miscible displacement projects had been reported' in the United States by early 1959. By far the most popular approach in these projects is the use of an LPG slug followed by dry gas. Laboratory tests have indicated that with a small miscible slug, amounting to several per cent of the hydrocarbon pore volume, practically 100 per cent recovery of the oil in place can be achieved and that all of the slug material can be recovered by a subsequellt gas drive. However, these experiments were conducted on small-diameter long cores that can be considered as essentially uni-dimensional reservoirs that do not represent actual field conditions. It soon became apparent that the inherently adverse mobility ratios existing in the reservoir cannot be ignored in any miscible displacement field project. When a less viscous fiuid such as an LPG slug drives a more viscous reservoir oil, fingers develop that reduce the areal sweep efficiency. The slze of the miscible slug to be used is a subject of some controversy. It has been proposed that the size of siug needed be calculated by setting lengths of the mixing zone proportional to the square root of the distance traveled. This proposal is based on experimental evidence' and theoretical considerations"' in which fingering was not a factor. A prerequisite for successful application of the miscible displacement process to field operations is a better understanding of the following factors. L What is the effect of mobility ratio on the rate of deterioration of a miscible slug? 2. How large a slug should be used for given reservoir conditions? 3. What is the sweep efficiency? The purpose of this investigation was to provide some additional laboratory data that should help to answer these questions. More specifically, it was intended to study more quantitatively the effect of viscous fiinger-ing, mobility ratio and slug size on the efficiency of this relatively new secondary recovery process by means of experiments on thin, horizontal, porous medium models.

By V. Apraxine, J. Lakaye, J. J. Saquet, P. Troch

Union Minière du Haut-Katanga owns concessions for extracting copper and associated metals in the high plateau region of Katanga. The concession is about 188 miles long by 44 miles wide and has three principal areas: Southern area-The Prince Leopold mine is an underground operation from which a copper-zinc sulfide ore is extracted. The mine and associated concentrator are at Kipushi. Copper concentrates are smelted and converted to blister copper at the Lubumbashi smelter at Elizabethville.

Jan 12, 1962

By E. T. Hunter

Surrounded by the 13,000-ft high peaks of the San Juan Mountains in southwestern Colo., the town of Silverton is the site of the extensive development operations initiated 20 months ago by Standard Metals Corp. Appropriately termed the Silverton Project, Standard's operation has now passed the half-way point in its program to reopen two mines that were once sizeable producers of copper, lead, and zinc ores.

Jan 1, 1961

By Walter Kauzmann

ALL viscous or plastic flow of incompressible matter is the result of shear strain; the changing shape of any body that is being plastically deformed can be completely described in terms of the shear strain occurring at each point in the body.[t] Furthermore, the relative amounts of shear strain occurring in different parts of a body under stress depend upon the relative rates of shear strain at those different points, so that if the dependence of the shear rate of any material on the temperature, shear stress, previous history, etc., were understood, the principles of plastic deformation would be known, and we could calculate how a body made of a given material, having a given shape, and subject to a specified system of forces, would change its shape with time. It may be said, then, that the problem of plasticity resolves itself into, first, the problem of the rates of pure shear processes, and second, the application of what is known about pure shear to actual cases. It is the purpose of this work to investigate the former problem -i.e., the dependence of shear rates on temperature, stress, etc.-from the standpoint of recent developments in the field of chemical-rate theory and with particular reference to the phenomena occurring in the creep of metals and in the plastic flow of crystalline solids in general. It is left for the mechanical engineer, and perhaps the expert in hydrodynamics, to deal with the problem of applications1 RESOLUTION OF MACROSCOPIC SHEAR INTO MICROSCOPIC MOVEMENTS; RESEMBLANCE TO CHEMICAL REACTIONS Just as any large body is made up of many small units, or atoms, so macroscopically observable shear is the result of many microscopic unit shear processes; just as the understanding of the behavior of large bodies demands the understanding of the atoms of which it is made, so the understanding of macroscopic shear demands the understanding of these fundamental unit processes. The study of shear from this "atomistic" point of view has made considerable progress. There has been fairly complete understanding of shear processes in gases for a long time, at least for nonturbulent flow, as a chapter on gaseous viscosity in any text on the kinetic theory of gases will prove. In recent years Andrade2 and Eyring3 have presented important theories for the flow of liquids and amorphous solids. Becker,4 Orowan,5 Taylor,6 Burgers,7 and Kanter8 have considered the

Jan 1, 1941

By John C. Draper

The principal object of an underground coal mine transportation system is to move coal from the face where it is produced to the outside of the mine where it is prepared for market. In addition to the movement of coal, a transportation system must also move supply materials to the inside ; it must move men in and out of the mine ; and it must move rock and other debris out of the mine for disposal. Usually, mine haulage is divided into three categories named for the various areas of the mine served : 1) Pace Haulage. This is used at face from the mining machine to the intermediate transport system. 2) Intermediate or Secondary Haulage. Generally this is used between face haulage and main haulage. Sometimes this is merely an extension of the main haulage. 3) Main Haulage. This extends from the secondary haulage to the outside and is usually either a track or conveyor system, sometimes a combination of both. Transportation modes of coal in the various areas pose different problems, but the whole system must be synchronized. For instance, at the face the coal should be removed quickly from the various places to facilitate the movement of machines, whereas the intermediate system just passes the same coal on to the main transportation system. Selection of the transportation system must be based on the seam height, mining methods used to extract the coal, capacity required, ease of coal handling, and haulage efficiency. When driving rooms, mine cars can be used. They often simplify supply haulage and rock handling because they can also handle these items. Conveyors could be used and would have a greater haulage capacity but they cannot handle supplies easily or segregate the rock. When using a different mining method, such as longwall, mine cars cannot be used because there is not sufficient space to move the cars at the face nor can the cars haul the coal without delays which would cause excessive losses in production. As for ease of handling

Jan 1, 1981

By Waldemar Lindgren

CONTENTS. [ ] I.-CHARACTER OF THE DEPOSITS. 1. Principal Features. IN many schemes of classification and description the term contact-deposit has been somewhat loosely applied to all accumulations of useful minerals (other than those of unquestioned sedimentary origin) which are enclosed between two different rocks. As thus used, the term may include deposits of widely differing origin, and, unless qualified, is not in place in a genetic classification. The present paper deals with a special class of contact-deposits. In many geological provinces, granular igneous rocks, such as granite, diorite and syenite, have broken through and invaded sedimentary rocks. The molten magma may in part have reached the surface and there solidified with relative rapidity as a lava. The largest masses of it, however, did not reach the surface, but cooled very slowly at considerable depth under great pressure, and eventually consolidated into a rock of granitic texture. Uplifts and extensive erosion may have followed; and at the present day, in many places, thousands of feet of material have been removed, bringing to the surface the intrusive granular rocks and their once deep-seated contacts with the sedimentaries which they shattered at the time of in-

Jan 1, 1902

Jan 1, 1879

By Gregoire Gutzeit

THE development reported in this paper was begun by the author a number of years ago, while he was a lecturer on complex chemistry and metallurgy at the University of Geneva, Switzerland, and in charge of that institution's research laboratory. Completion of the development and reduction to practice did not occur until last year at the Westport mill, laboratories and testing plant of the Dorr Company, where this method is now in general use for identifying and localizing the mineral constituents of both metallic and nonmetallic ores. It has proved to be a practical tool of the metallurgical staff at the Westport mill, devising unusual milling flowsheets for complex and refractory ore bodies. In a number of instances the findings have been successfully used as fundamental factors in the design and specification of complete metallurgical plants. Seven examples of the use of this method in solving practical milling problems are included in this paper. GENERAL OUTLINE The microscopic study of an ore, at first only of scientific interest, has proved extremely useful both in practical geology and in ore dressing. The binocular magnifying lenses for rough observation of the products of an ore-dressing plant have been in use for a long time; but only within the last few years has a systematic microscopical examination of ore samples become a normal tool of any research laboratory dealing with ore-dressing problems. Such an investigation avoids considerable loss of time as well as empirical trials and useless experimentation. It will generally indicate the correct grinding and often will suggest the proper method of treatment. The petrographic determination of transparent minerals in thin sections, or even in grains, has been perfected, and very accurate methods have been devised to meet any requirement, such as Feodorof's rotating stage on the petrographic microscope. Almost all transparent minerals can be positively identified by their optical properties; i.e., isotropism, anisotropism, color, pleochroism, refractory index, cleavage, crystal form, birefringence, and others. The identification of opaque minerals is a much more difficult problem and can be done only by using polished specimens. Unfortunately, most of the valuable metallic ores, and even some of the nonmetallic ones, are not transparent; therefore it has been necessary to develop a special technique for the determination of these minerals. Some optical properties-for instance, isotropism, anisotropism, color, cleavage, reflecting power-are often adequate in roughly classifying the mineral. Only "reflecting power" is a measurable value, provided special photometric equipment (ocular photometer or Orcel's photoelectric cell) is available. The other optical properties mentioned are more or less relative,

Jan 1, 1942

By Kenneth C. Vincent, A. M. Gaudin

In a study1 of the action of amyl xan-thate on chalcocite in water suspension, it was found that if the xanthate is added in relatively large quantity the xanthate group can be accounted for in three forms: (1) as xanthate ion remaining in water, (2) as benzene-soluble cuprous xanthate on the chalcocite, (3) as a benzene-insoluble coating on the chalcocite. Reduction in the amount of xanthate added leads to disappearance of form I then of form 2. With minute quantities of added xanthate, substantially all the reagent is of the "unleachable" kind. Yet this unleach-able xanthate can be dissolved by pyridine to form a soluble cuprous xanthate complex, and it is sufficient in effectiveness to make chalcocite flotable even if insufficient in quantity to form a complete mono-molecular film on the mineral. In that study it was also found that chalcocite abstracts cuprous xanthate from benzene so1ution, in what may (or may not) be a case of molecular adsorption. It seemed desirable, therefore, to study further the "unleachable" xanthate on the chalcocite, and particularly to ascertain whether it is formed as a result of the benzene leach or is actually formed during the conditioning of chalcocite in aqueous xanthate solution. A 'splendid tool to make such studies has recently been perfected; that is, the use of radioactive spies or tracer atoms. With this tool, it was thought possible to answer the problem stated above, but, unfortunately, this did not prove to be true. Answer to the flotation question was clouded by the existence of rapid and selective diffusion of copper atoms in the solid mineral—a phenomenon that was totally unexpected yet remains interesting and perhaps important. Method of Radioactive Spies The method of radioactive spies is discussed in many places. Two convenient references are the article by Evans2 and the book by pollard and Davidson.3 The method was first developed by van Hevesy and paneth in 1013, when only natural radioactive isotopes were available. These isotopes are few in number, and so the method remained limited in scope. Recently the synthesis of over 350 active isotopes of all the known stable chemical elements4 has opened widely expanded possibilities for the method, A fundamental tenet of the method is that a radioactive atom and a nonradio-active atom are exactly alike until disintegration of the radioactive atom. Then, by its sudden death, the spy reveals its location. The relative abundance of spies at various locations makes it possible to ascertain the relative abundance of the corresponding nonradioactive atoms at the same times and locations. A second fundamental tenet of the method of radioactive tracers is that the radioactivity lies in the nucleus of the atom: transfer of radioactivity from one

Jan 1, 1947

By Kenneth C. Vincent, A. M. Gaudin

In a study1 of the action of amyl xan-thate on chalcocite in water suspension, it was found that if the xanthate is added in relatively large quantity the xanthate group can be accounted for in three forms: (1) as xanthate ion remaining in water, (2) as benzene-soluble cuprous xanthate on the chalcocite, (3) as a benzene-insoluble coating on the chalcocite. Reduction in the amount of xanthate added leads to disappearance of form I then of form 2. With minute quantities of added xanthate, substantially all the reagent is of the "unleachable" kind. Yet this unleach-able xanthate can be dissolved by pyridine to form a soluble cuprous xanthate complex, and it is sufficient in effectiveness to make chalcocite flotable even if insufficient in quantity to form a complete mono-molecular film on the mineral. In that study it was also found that chalcocite abstracts cuprous xanthate from benzene so1ution, in what may (or may not) be a case of molecular adsorption. It seemed desirable, therefore, to study further the "unleachable" xanthate on the chalcocite, and particularly to ascertain whether it is formed as a result of the benzene leach or is actually formed during the conditioning of chalcocite in aqueous xanthate solution. A 'splendid tool to make such studies has recently been perfected; that is, the use of radioactive spies or tracer atoms. With this tool, it was thought possible to answer the problem stated above, but, unfortunately, this did not prove to be true. Answer to the flotation question was clouded by the existence of rapid and selective diffusion of copper atoms in the solid mineral—a phenomenon that was totally unexpected yet remains interesting and perhaps important. Method of Radioactive Spies The method of radioactive spies is discussed in many places. Two convenient references are the article by Evans2 and the book by pollard and Davidson.3 The method was first developed by van Hevesy and paneth in 1013, when only natural radioactive isotopes were available. These isotopes are few in number, and so the method remained limited in scope. Recently the synthesis of over 350 active isotopes of all the known stable chemical elements4 has opened widely expanded possibilities for the method, A fundamental tenet of the method is that a radioactive atom and a nonradio-active atom are exactly alike until disintegration of the radioactive atom. Then, by its sudden death, the spy reveals its location. The relative abundance of spies at various locations makes it possible to ascertain the relative abundance of the corresponding nonradioactive atoms at the same times and locations. A second fundamental tenet of the method of radioactive tracers is that the radioactivity lies in the nucleus of the atom: transfer of radioactivity from one

Jan 1, 1947

By R. E. Zimmerman

The separation of fine sizes of coal from its impurities by means of various flotation methods has become of increasing importance in the coal industry. This, no doubt, will be even more so in the future as the quantity of high grade coal is depleted, particularly that used for metallurgical purposes. The purpose of this paper is to describe and report the results of research work done under the auspices of the Pittsburgh Coal Co. to determine the amenability of their bituminous fine sizes of coal to flotation, to investigate the value of various reagents and factors affecting their use, and compare the results between froth flotation and bulk oil flotation. Compared with the preferential flotation of complex minerals, or ores, the flotation of coal is comparatively easy. However, this statement should not lull one into the feeling that there are no special problems involved. For instance, the separation of coal from pyrite in high sulphur coals is still far from being 100 pet successful. Size consist has considerable effect on reagent consumption and recovery. Other factors will be described and finally it must be remembered that in the flotation of coal a low priced material is being treated and thus economic considerations govern more closely its application than is generally the case in treating other minerals. As a result of the research work done by the Pittsburgh Coal Co. on the flotation of coal, it was concluded that it was practical to clean the —48-mesh coal commercially by froth flotation and after several different types of flotation units and circuits were investigated by means of pilot plants, large scale units were installed at their Champion Nos. 1, 4 and 5 Preparation Plants for the cleaning of —48-mesh slurries. These large scale operations have been recently described by D. H. Davis.' C. P. Proctor and C. B. Carlson2 in their chapter on Froth Flotation of Coal in the AIME Seeley W. Mudd series book on Coal Preparation describe some of the practical applications of our Pittsburgh Coal Co. laboratory work in actual plant practice as well as summarizing part of the investiga-tional work. The author presents this paper, however, as a supplement to their reports, and records the basic research accomplished in the laboratory investiga-tional work as well as the results of experiments using bulk oil flotation. In presenting this work the author wishes to state much more work must be done in applying the principles of flotation to cleaning coal, especially in view of recent studies and practices in other mineral beneficiation fields. Methods of Conducting Laboratory Tests The bulk of the research work was conducted in the laboratory of the Champion No. I Preparation Plant. This plant has elaborate facilities for sampling and analyzing coal and proved to be an admirable location for the investigational work. Four types of laboratory flotation ma-

Jan 1, 1949

By Zay Jeffries

It has been known for centuries that iron and steel could be hardened by cold hammering and that the metal could be restored to the normal condition by heating to a red heat arid cooling, either rapidly or slowly with nearly pure iron, but slowly with steels containing considerable carbon. The art of tempering steels is also very old. When a medium- or high-carbon steel is quenched from a cherry-red heat, the hardness is increased; this hardness can be reduced by heating to various temperatures below the lower thermal critical point,, which is near 700" C. The present paper will not consider these old and well known changes in iron and steel below the thermal critical range but will confine itself to the more unusual changes, some of which have been studied recently. Stromeyer,1 for example, In 1886, reports that both working steel and heat treatment of steel in the blue-heat range arc highly injurious. Recently, however, some metallurgists believe that the straiglltening of warped steel forgings at a blue heat produces a beneficial effect on the metal2 The Engineering Division of the National Research Council has constituted a committee on Physical Changes in Iron and Steel below the Thermal Critical Range, which has the following personnel: K. R. -Abbott, H. C. Boynton, William Campbell, J. V. Emmons, F. B. Foley, H. J. French, H. M. Howe, Zay Jeffries (chairman), F. C. Langenberg, J. A. Mathews, P. D. Merica, A. H. Miller, J. H. Nelson, G. A. Reinhardt, W. E. Ruder, H. F. Wood. This committee is studying several aspects of the physical changes in iron and steel. The results, reported in the literature and obtained by recent experimentation, will be given; this will be followed by a general theoretical discussion of the more important

Jan 1, 1922

By Zay Jeffries

It has been known for centuries that iron and steel could be hardened by cold hammering and that the metal could be restored to the normal condition by heating to a red heat arid cooling, either rapidly or slowly with nearly pure iron, but slowly with steels containing considerable carbon. The art of tempering steels is also very old. When a medium- or high-carbon steel is quenched from a cherry-red heat, the hardness is increased; this hardness can be reduced by heating to various temperatures below the lower thermal critical point,, which is near 700" C. The present paper will not consider these old and well known changes in iron and steel below the thermal critical range but will confine itself to the more unusual changes, some of which have been studied recently. Stromeyer,1 for example, In 1886, reports that both working steel and heat treatment of steel in the blue-heat range arc highly injurious. Recently, however, some metallurgists believe that the straiglltening of warped steel forgings at a blue heat produces a beneficial effect on the metal2 The Engineering Division of the National Research Council has constituted a committee on Physical Changes in Iron and Steel below the Thermal Critical Range, which has the following personnel: K. R. -Abbott, H. C. Boynton, William Campbell, J. V. Emmons, F. B. Foley, H. J. French, H. M. Howe, Zay Jeffries (chairman), F. C. Langenberg, J. A. Mathews, P. D. Merica, A. H. Miller, J. H. Nelson, G. A. Reinhardt, W. E. Ruder, H. F. Wood. This committee is studying several aspects of the physical changes in iron and steel. The results, reported in the literature and obtained by recent experimentation, will be given; this will be followed by a general theoretical discussion of the more important

Jan 1, 1922

By L. F. Marek, G. W. King, A. Bogrow

THE purpose of this paper is to present the data and some interpretation of the results of a laboratory study of the reduction of iron ore and the deposition of carbon from the reducing gas mixtures in such reductions. One major object of the study was to determine the effect of gas pressures on these chemical processes. Effort was made to approximate the conditions of temperature, gas composition, linear and mass gas velocities, pressure range, and extent of reduction prevailing in commercial blast furnaces. The results show that the reduction of Fe203 proceeds by two steps, largely consecutive under the conditions used herein: reduction of Fe203 to FeO, and reduction Of FeO to Fe. Unless the gas has a CO/CO2 ratio greater than 2.1 only the first step occurs under these conditions (850°C) but the following generalizations apply to either step or to the combination. The rate of reduction of relatively fine ore particles at any time is proportional to the mass rate of supply of CO (provided some of it is thermodynamically available) the rate therefore is proportional to the linear velocity at constant pressure, or to the pressure at constant linear velocity. Thus, the rate of reduction may be increased without increase in linear velocity f the reducing gas by increasing the mass velocity of the gas and increasing the pressure correspondingly to avoid any increase in the linear velocity. The rate "constants"-i.e., the efficiency of conversion of the "available" CO supplied-is not actually constant but decreases as the reduction proceeds, and is a function only of the state of the ore; i.e., of the amount of reduction already accomplished and hence of the amount of CO passed. The particle size Of ore used in nearly all the experiments was relatively small (8 to 14-mesh). The rate of reduction in run 16 with 3 to 8-mesh ore particles is within experimental error the same as with the finer ore. Although this would indicate an absence of effect due to particle size in this range of ore particles, it is desirable to have more data on other ore sizes and on ore of different densities before arriving at any generalizations on this point. Although it is possible to extend the analysis of these results to consideration of the more detailed kinetics and mechanism of iron oxide reduction, such extension is beyond the scope of the present paper. From the experiments on carbon deposition, it was evident that if carbon deposition is increased at all by the application of pressures up to 10 psi ga., such increase appears to be less than the experimental and analytical error. It appears safe to conclude that at top pressures on the order

Jan 1, 1947

By C. W. MacGregor

THE observation of the flow layers, or Lüders' lines, produced in mild steel when it is stressed into the plastic range often provides considerable useful information for the study of the fundamental mechanism of the plastic flow of metals. It is a commonly observed fact that as soon as the upper yield point in a mild-steel tensile-test bar is passed, an unstable condition develops in the equilibrium, the load on the testing machine drops and if the surface of the bar contains a thin mill scale, the latter begins to flake off rapidly along certain "lines." These "lines" are in reality traces of wedge-shaped flow layers and are formed by the intersection of the surface of slip and the surface of the bar. The average plane of the flow layer itself has been found by various experimenters to be inclined at an angle of approximately 45° to the axis of the test bar. In a body of more complicated shape stressed in possibly a different man-ner, the tangent planes to the flow layers at each point seem in many cases to be inclined at an angle of about 45° to the principal stress direc-tions at the point. As examples of the latter may be mentioned the logarithmic spirals obtained when a rivet hole is punched in a thin plate, or when a tube is subjected to internal pressure only, etc. Hence if the flow layers are observed from an experiment, the shear-stress trajectories -the curves indicating the directions of the maximum shearing stresses in the body-may then be approximately determined. Since the latter curves form an orthogonal family inclined at 45° to the principal stress directions, the family of principal stress trajectories, or the curves indicating the directions of the principal stresses, may be thus obtained. Although the discontinuous type of stress-strain curve at the yield point is commonly observed with test bars of mild steel, more recent experiments have shown that this is by no means the only material exhibiting this interesting phenomenon. A similar effect has been observed in zinc and cadmium crystals, by Becker and Orowan;1 in duralumin and other aluminum alloys, by Dawidenkow,2 Elam,3 Fell, and others; in copper and copper-alloy crystals, by Elam;5 in brass by Elam;5 in brass wires by deForest;6 in higher carbon steels, tungsten steel, and

Jan 1, 1939

By Richard P. Rothwell

Fires in mines are so serious in their consequences and of such frequent occurrence, that their causes and the means of extinguishing them are certainly questions of the greatest interest to a large part of the engineering profession. We have already, in this country, many mines which have been burning for years, and though our hard anthracite is so difficult to ignite that for a quarter of a century after it was first discovered it mas not known how to burn it except with the aid of an artificial blast, yet most of the fires which have occurred underground have been in anthracite mines, and in the coal itself. The injury which these fires have caused to properties in various parts of the anthracite regions, and the cost of extinguishing them, would amount to many millions of dollars, and they have also occasioned the loss of many valuable lives. It is not surprising, therefore, that the subject has already attracted much attention, and the exercise of great ingenuity; and the present communication is made less with the expectation of announcing anything new, than with the object of putting upon record the present state of our knowledge on this subject, or, in other words, of indicating how defective are the present means of combating underground conflagrations. Causes of Mine Fires.—Even upon the surface, fire is a terrible foe to contend with, and there is probably no other which inspires such thorough and well-founded alarm. With what feelings, then, must we look upon this destructive element, when its field is in the narrow galleries of a mine, where the poisonous products of combustion, spreading in every direction, protect, in the most effectual manner, the fire itself from the attacks of extinguishers, while, if the face of attack be ventilated so as to enable then] to approach the seat of the fire, the air current simply increases the extent and violence of the conflagration. Fires underground originate in as various ways as those on the surface, and it is scarcely necessary to say that, except in the rare cases where they are the result of design, they are invariably classed as " accidents," and most generally as " unavoidable accidents." In reality, by an intelligent understanding of their causes and with due precautions, they can almost always be prevented. Ignorance and

By Hans Lundberg

IN ORDER to comprehend the help and information that may be expected from electrical prospecting, it is necessary to have at least a general knowledge of the methods and principles involved in preparing and interpreting results obtained in the field. Electrical prospecting is rather complicated, both in theory and practice, and in order to make a brief description clear to the practical mining man it has been necessary to idealize and generalize the problems, at the risk of having such simplification criticized by the theoretical man. This simplification must not be misinterpreted as showing a lack of theoretical knowledge. FIG. 1.-FLOW OF CURRENT IN AND AROUND A CONDUCTING BODY. For its operation, electrical prospecting mainly depends on-the fact that most metallic ores conduct an electric current much more readily than barren rocks. If an electric current flows through a block of ground within which a body of chalcopyrite is enclosed in country rock of schist, the current will find less resistance to its passage through the chalcopyrite than through the schist, even though the passage through the latter be much shorter. This is because the longer path through the chalcopyrite offers less resistance, owing to the superior electrical conductivity of the chalcopyrite (Fig. 1).

Jan 1, 1928

By A. M. Gaudin

A great number of hypotheses has been advanced to explain the complex phenomena that are encountered in flotation. In the days of bulk-oil flotation, when a large quantity of oil was employed, it was observed that the oil-mineral aggregate floated above the ore-pulp because of its lesser density. With the advent of froth-flotation this phase of the theory had to be modified to take into account the presence of air bubbles. The reason why the mineral-bearing froth of today rises to the top of flotation cells is, of course, because the air-mineral aggregate, with whatever reagent may be associated with it, is lighter than the pulp. In an attempt to explain froth-flotation the fact has been emphasized that certain minerals are wetted and therefore remain in water; while others are not wetted and therefore become associated in preference with air. Such an "explanation" does not explain facts, it merely states them; for instance, it does not explain why minerals are wetted under some circumstances and not wetted under others. Going somewhat further, the wetting or nonwetting of minerals by water has been ascribed' to differences in the angles of contact between oil droplets and mineral surface at the surface of the minerals. This explanation, however, was abandoned when soluble flotation reagents came to replace the so-called "insoluble" reagents. Another theory, sponsored about 10 years ago by Ralston,² involves the effects of electric charges at the surface of the mineral particles and air bubbles. This theory, unfortunately, was not developed as fully as it seems desirable. The belief that adsorption phenomena might play a preponderant role in flotation3 has been rather widespread for the last 10 years. Unfor-

Jan 1, 1928

By C. D. Thompson, D. C. Violetta, C. A. Czako

The mechanics of the continuous sintering process are briefly reviewed and the application of this process for the beneficiation of principal minerals used in making cement is shown. Pilot plant tests using pyrobeneficiation techniques were conducted with mixtures of limestone and shale in various ratios. Results are illustrated and show the percentage removal of carbon, carbonates, sulfur, alkalies, and volatiles as a function of the limestone-shale ratio. Tests with varying quantities of solid fwls, added to mixtures containing limestone and shale in a 4 to 1 ratio, were made to attain optimum elimination of the volatile constituents. Experimental results show that 90 pct of these constituents were removed during the calcination sintem'ng process. The advantages of using the beneficiated material for making cement are discussed with regard to prepam'ng, handling, and clinkering operations. A sintering process for treating raw materials or kiln waste products which contain high amounts of alkaline materials is described. Tests were performed with a high alkaline waste dust mixed in a 1 to 1 ratio with raw cement meal. The data from these tests and others using different halides for aiding alkali removal are evaluated by the alkali content of the cement clinker. Test results showed that the Dwight-Lloyd process could be applied with facility in beneficiating raw materials for cement making. Substantial quantities of deleterious volutile constituents were removed by calcining and sintering techniques. The continuous sintering process has been applied for a number of years as a means of beneficiating minerals for subsequent conversion to merchantable products. The process was developed and first used for nonferrous metallurgical applicatfons. However, it has risen to prominence for ferrous metallurgical applications where last year in the U.S. and Canada nearly 40 million tons of iron ore were treated by grate firing processes. Through the years of process development many investigators have realized the versatility of the sintering process and have directed experiments toward the use of it for applications with nonmetallic minerals. These have included calcining limestone, carbonizing coal, expanding shale, and burning cement raw meal. Today commercial sintering plants produce cement clinker from mixtures of limestone and shale, lightweight aggregate from shale or clay, and calcined products from phosphate shale. The mechanics of the downdraft sintering process have been presented by many authors. In general practice the materials to be agglomated are mixed as moistened fines with a solid fuel and this mixture is spread uniformly on the grates of the sintering machine. The charge is then momentarily directed under an ignition furnace. After ignition a continuous downdraft of air promotes combustion of the fuel and through heat transfer particles become partially fused into a coherent mass. This is cooled from continued draft induced after combustion. Many investigators have shown that distinct zones are formed during the process of sintering iron ores. At the midway point of the sintering process these are prominent and are, respectively, from the top of the bed to the bottom, comprised of a cooling zone of sintered material, a combustion zone of sinter formation, a calcination zone, a drying zone, and a zone of unreacted materials. Completion of sintering occurs near the discharge end of the machine where the firing zone approaches either the grates or grate dressing material called hearth layer. Here the peak draft temperature usually can be noted in the windboxes. The zonal pattern has been illustrated with the use of graphs which show thermal gradients as they progress through the bed of materials during sintering. Fig. 1 shows, in simplified form, thermal gradients existing when clinkering cement on a sintering machine. The thermal gradients illustrated are for periods of initiation, midway and completion of the clinkering process. The occurrence of these zones has importance for the beneficiation of cement raw materials. A research program was performed at the Dwight-

Jan 1, 1961

By Robert Mehl

IN examining the progress of metallurgical science, the critic must remember that most of our present knowledge of metals and alloys has been accumulated through the needs of industry and commerce rather than through the desire and efforts of a large body of scientists interested primarily in developing a science of metals. The progress of metallurgy, scientifically speaking, has been irregular, and little given to the exhaus-tive exploitation of important scientific fields. The experienced engineer now recognizes the need for the development of the basic science upon which his engineering rests. In addition to the increase in knowledge which results from the normal requirements of industry, a development of the basic science of the behavior of metals and alloys is as desirable in metallurgy as in any other branch of science and engineering. The continued growth of the science of metals-as of every other science-requires studious attention to the principles that underlie the behavior of matter, with the result that knowledge in the several fields of interest should continue to increase. Among the various subjects recognized as important in physical metallurgy few have a wider significance than that of diffusion in solid metals. The phenomena of diffusion are intimately related to many basic problems of the metallic state, but in addition to this, the process of diffu-sion is of first importance practically. The formation of alloys by the annealing of mixed powders, first practiced by Faraday and Stodart81 in 1820 and in more recent years investigated by Masing187,189 and others, has led to the development of special alloys like Carboloy, Vascoloy-Ramet, Genelite, Elcon68, and has recently been applied to the production of noble-metal alloys for electrical contacts"'.

Jan 1, 1936