Search Documents

By Robert S. Dewey

Drilling in West Texas during 1942 was substantially less than in the previous year. In all. 1267 Wells were drilled, as compared with 2325 wells in 1941. Of these 1267 wells, 1052 oil wells, 10 gas wells and 69 dry holes were drilled in proven fields and 36 oil wells, one gas well and 99 dry holes were wildcat operations. Of the 36 wildcat wells completed as oil producers, 16 led to new field discoveries, three found new productive horizons in old fields, and 17 extended the productive limits of established fields. Where semiwildcat drilling took place along established productive trends, there was often no sharp demarcation between wildcat wells that extend field limits and normal development to fulfil lease obligations, other than the arbitrary classification of a well as a wildcat if it was drilled at a distance of 2 miles from a producing oil well. The dry hole drilled on the edge of a field may have proved a more hazardous operation than a semiwildcat drilled several miles from production but favorably located on structure. The percentage of successful wildcatting ranges from 26.5 down to 14 per cent, dependent upon the degree of inclusion of the semiwildcat operations. Irrespective of which figure was used, the West Texas area maintained its better than average exploratory position. No doubt a number of factors may have influenced the extent of the 1942 development. Among those arising from the economic dislocation attendant on the war effort, the following are worthy of note. Owing to inductions into the armed forces and shipyard competition for mechanically trained men, experienced drilling personnel was sharply reduced, thereby increasing drilling costs and well-completion hazards. Replacement labor has not met the same standard of responsibility or workmanship to which the oil industry has grown accustomed. Increased military consumption of aviation gasoline and other crude products, coupled with decreased domestic consumption of lower-octane gasoline, has stimulated the market demand for the types of sweet crude most readily processed with available refinery equipment to meet war requirements, and has depressed the market demand for the sour West Texas crudes. As a majority of the purchasers of West Texas crude normally ship a substantial portion of sour crude to the refineries on the Atlantic seaboard, the loss and diversion of tanker service between Gulf Coast and north Atlantic ports have further curtailed the market demand for this type of crude oil. As some purchasers of crude oil were able to move by pipe line their West Texas trunk-line capacity to Midwestern refining centers, they were not impelled to curtail purchases of West Texas crude. The varying ability of the purchasers of crude oil to market West Texas crude was reflected back to various fields to which they were connected, causing an unequal distribution of production as among fields and operators. The pipe-line runs from the West Texas-New Mexico area decreased from approximately 354,000 bbl. Per day in January to about 265,000 bbl. in December 1942. .Approximately 2,991,000 bbl. of West

Jan 1, 1943

By Robert S. Dewey

Drilling in West Texas during 1942 was substantially less than in the previous year. In all. 1267 Wells were drilled, as compared with 2325 wells in 1941. Of these 1267 wells, 1052 oil wells, 10 gas wells and 69 dry holes were drilled in proven fields and 36 oil wells, one gas well and 99 dry holes were wildcat operations. Of the 36 wildcat wells completed as oil producers, 16 led to new field discoveries, three found new productive horizons in old fields, and 17 extended the productive limits of established fields. Where semiwildcat drilling took place along established productive trends, there was often no sharp demarcation between wildcat wells that extend field limits and normal development to fulfil lease obligations, other than the arbitrary classification of a well as a wildcat if it was drilled at a distance of 2 miles from a producing oil well. The dry hole drilled on the edge of a field may have proved a more hazardous operation than a semiwildcat drilled several miles from production but favorably located on structure. The percentage of successful wildcatting ranges from 26.5 down to 14 per cent, dependent upon the degree of inclusion of the semiwildcat operations. Irrespective of which figure was used, the West Texas area maintained its better than average exploratory position. No doubt a number of factors may have influenced the extent of the 1942 development. Among those arising from the economic dislocation attendant on the war effort, the following are worthy of note. Owing to inductions into the armed forces and shipyard competition for mechanically trained men, experienced drilling personnel was sharply reduced, thereby increasing drilling costs and well-completion hazards. Replacement labor has not met the same standard of responsibility or workmanship to which the oil industry has grown accustomed. Increased military consumption of aviation gasoline and other crude products, coupled with decreased domestic consumption of lower-octane gasoline, has stimulated the market demand for the types of sweet crude most readily processed with available refinery equipment to meet war requirements, and has depressed the market demand for the sour West Texas crudes. As a majority of the purchasers of West Texas crude normally ship a substantial portion of sour crude to the refineries on the Atlantic seaboard, the loss and diversion of tanker service between Gulf Coast and north Atlantic ports have further curtailed the market demand for this type of crude oil. As some purchasers of crude oil were able to move by pipe line their West Texas trunk-line capacity to Midwestern refining centers, they were not impelled to curtail purchases of West Texas crude. The varying ability of the purchasers of crude oil to market West Texas crude was reflected back to various fields to which they were connected, causing an unequal distribution of production as among fields and operators. The pipe-line runs from the West Texas-New Mexico area decreased from approximately 354,000 bbl. Per day in January to about 265,000 bbl. in December 1942. .Approximately 2,991,000 bbl. of West

Jan 1, 1943

By Robert J. Linney

IN the latter part of the year 1943, it was decided to experiment with diamond-drill blast holes in the Old Bed magnetite mine at the Mineville mines of the Republic Steel Corporation, in sections of the ore body where vertical dimensions were large and where development for sublevel bench stopes had already been done. Other possibilities of application for this drilling method were in the reclamation of old floors and pillars in the pitching folds of the Lower Old Bed ore body and in the reclamation of large vertical pillars in the " 21 " Bonanza-Joker ore body. The cross sections and views of the two ore bodies will show the conditions to which the diamond-drill method has been applied. The Lower Old Bed magnetite ore body is lenticular and dips approximately 30° toward the southwest and strikes generally southeast and northwest. An intensely folded structure, which pitches generally on an axis approximately at right angles to the strike, is continuous from the uppermost old workings down to the present bottom of the mine, and probably continues with depth. On successively lower levels this folded structure becomes greater in vertical dimensions and the two folds are closer together in a horizontal dimension. As shown in Fig. 1, this folded structure gives to parts of the ore body considerable vertical dimensions, which provide areas that were developed for sublevel bench stoping above a slushing drift, as shown in Fig. 2. It was in one of these previously developed sublevel bench stopes, No. 26 on the 1185-ft. level, that the diamond-drill blast-hole method was applied for mining the upper sublevel. The lower sublevel was underhand-bench-drilled to the finger raises of the scram drift below. The roof of this stoping area began to break and spall on the lower sublevel, causing the roof to become inclined. Along the hanging wall of the stope this reached an elevation about half way between the two sublevels. A smooth schistose seam in the hanging wall causes the ore to break away freely. Therefore, if bench mining had been carried on in the upper sublevel, a dangerous condition of poorly supported benches would have resulted. When the drillers were slashing across the sublevel to footwall and hanging wall to make a bench, spalling roof of the opening below would probably have carried away part of the bench, and would have left a dangerous place in which to continue underhand benching. A 6 by 8-ft. raise had been driven between the lower stope and the upper sublevel about 200 ft. from a manway. It was decided to use this raise for a starting cut and to arrange holes as shown in Fig. 3, so that a slot would be opened across the ore body between the footwall and hanging wall. This slot would then be used for the purpose of breaking into the ore; by blasting vertical rings of holes drilled at right angles to the axis of the pitching folds as nearly as possible. Layouts of this slot drilling and the rings adjacent are

Jan 1, 1945

By C. C. Herrick

The vapor pressure of indium has been measured by the torque-effusion technique, as a function of temperature between 1102o and 1422oK. For liquid indium, the vapor pressure (in atmospheres) can be represented by the equation -R In P = 5.782 x104/T - 25.29from 1000o to 1422oK. Extrapolation yields a calculated normal boiling point of 2329°K and a heat of vaporization at 298 oK of 58.09 kcal per mole by the third-law method and of 58.39 kcal per mole by the second-law method. Calculations indicate that the free-energy functions of Hultgren are to be preferred to those of Guruich. BECAUSE of the potential uses of liquid metals, it is important that convenient experimental methods be developed which will lead to a sufficient body of thermodynamic data so that reasonable estimates of properties of liquid metals can be made. Indium is particularly well-suited to investigation, since it remains liquid over a long temperature interval, it alloys readily, suitable containers for it are easily procured, and relatively few investigations of its thermodynamic properties in the region above 1000°K have been made. PREVIOUS RESEARCH The first determination of the vapor pressure of indium was made by Anderson,' using the Knudsen method and silica-lines stainless-steel cells. Kohlmeyer and spandau2 determined the normal boiling point, and a mass-spectroscopic investigation has been made by Lyubimov and Lyubitov.3 (Unfortunately, only an equation representing the data of the latter investigators has been available to us.) Hultgren et al.4 and Gurvich5 have published discordant tables of the free-energy functions for indium. EXPERIMENTAL METHOD The torsion-effusion principle has been described amply in the literature.8,7 With this method, one observes the angular deflection induced by effusion of vapor from a multihole effusion cell which is suspended from a filament producing a small rotational restoring force. The pressure within the effusion cell can be computed from the relation ziaifiai where k is the torsion constant of the filament, 6 is the observed angular deflection, and ai, fi, and qi are the area, force factor, and moment arm of the ith effusion orifice. The force factor f is analogous to the Clausing factor,' and corrects for the reduction in effusive force attributable to the finite geometry of the effusion orifice. Schultz and Searcy' have tabulated the force factors for various tube geometries. EXPERIMENTAL APPARATUS The physical arrangement employed in this study is shown in Fig. 1. The furnace elements are six Globar heat rods with 15-in. hot zones. Temperature is maintained to * 1°K by a Beck mechanism driving two 26-amp Powerstats in parallel. A Pt (Pt, Rh 10 pct) thermocouple serves as the sensing element. Four inner tubes act as vibration isolators; the air pressure required for maximum isolation was determined empirically, and is maintained by a solenoid valve. The tungsten fiber, 9 by 0.002 in., is joined to an 0.008-in. tungsten wire or graphite rod via a machined lightweight chuck.

Jan 1, 1964

By Robert S. Dewey

More wells were drilled in West Texas† during 1944 than in any year since 1941. As compared with 1943, there was an 82.5 per cent increase in the total number of completed wells. The 1646 wells required an estimated 140,715 days to complete for a total of 7,632,249 ft. An average of 85 completion days was required to drill to an average of 4630 ft. This depth is approximately 100 ft. greater than that of the previous year. It is estimated that $100,000,000 was invested in drilled wells. As of Dec. 31, 1944, there were 270 field and 91 wildcat wells being drilled. While an identical number of wells were drilling Dec. 31, 1943, the proportion of wildcats increased in 1944 from 19.7 to 25.2 per cent. During 1944, oil wells were completed in 103 of the 164 fields in West Texas. Of the 1361 oil wells, 385 were in Slaughter, 116 in Fullerton, 63 in North Cowden, 62 in Fuhrman-Mascho, 59 in Wasson, 52 in Westbrook and 47 in North Ward. Approximately 22 per cent of the wildcat drilling was to pre-Permian formations. Despite the increasing proportion of wildcat wells drilled, the wildcat discovery rate has declined since the year 1942. AS compared with 1943, the number of wildcat wells drilled increased from 11.7 to 12.7 per cent and the footage in wildcat exploration increased from 13.3 to 13.8 per cent of the total. The monthly production of crude continued to increase to a peak of 15,336,000 bbl. in October 1944. As compared with a similar peak production in October 1943, there was a 37.3 per cent increase. The yearly production increased from 98,165,-ooo bbl. in 1943 to 159,943,000 bbl. in 1944, an increase of 62.8 per cent. Based upon an assumed average price of $1.00 per barrel and less 1/8 royalty, the gross return to the producer amounts to $140, 000,000. From 1943 to 1944, the average number of producing wells increased 6 per cent while the average daily production per well increased 53.1 per cent. The average daily production per well increased from 17.5 bbl. in 1943 to 26.8 bbl. in 1944. The proportion of flowing wells decreased from 50.5 per cent in January to 49.1 per cent in December 1944. Drilling With the continued shortage of labor and materials, drilling costs have risen sharply. Just how much is difficult to ascertain. Owing to competition for available drilling rigs, contractors are reluctant to assume drilling risks. In consequence, some contracts are let on a cost plus basis, or day work below some specified depth with the operator furnishing part of the consumable materials, such as mud and drilling bits. Contractors are having difficulty in maintaining full and effective drilling crews with insufficient and inexperienced labor. Service companies have inadequate labor and equipment to meet their appointments promptly. Pipe Lines The Gulf Pipe Line Co. increased the capacity of its 10-in. main line by filling in gaps amounting to 75 miles on the loops between Judkins and Weatherford, Texas.

Jan 1, 1945

By Shiou-Chuan Sun

THE fact that coals of different ranks and even of the same rank differ greatly in their amenability to iroth flotation is well known. In recognition of the need for an explanation of this phenomenon, two hypotheses have been suggested. Wilkinsl reported that the floatability of coals increased with an increase of the carbon content or rank. This postulate is handicapped by the fact that bituminous coals that possess moderate carbon contents are actually more floatable than anthracite coals that have high carbon contents, as shown in columns 6 and 9 of Table I. Taggart and his associates' implied that the difference of floatability between bituminous and anthracite coal was caused by the variation of carbon-hydrogen ratio. This is not applicable to the relative floatability of other coals and carbons. For example, column 11 of Table I shows that the carbon-hydrogen ratios of low-floating lignitic coal and non-floating animal charcoal are not only smaller than the moderate-floating anthracite coal, but are also similar to the high-floating bituminous coal. Furthermore, according to this hypothesis, high temperature coke-A (464), Ceylon graphite (1238), and lamp-black (357), all possessing extremely high carbon-hydrogen ratios, should be less floatable than other substances having much lower carbon-hydrogen ratios such as high volatile-B bituminous coal (11.9 to 22), anthracite coal (35.7 to 60.5), lignitic coal (15.6 to 33.6), and charcoal (13 to 26.2). However the former group is actually more floatable than the latter group. In this paper, a surface components hypothesis is Proposed to explain the different floatabilities of coals, carbons, and hydrocarbon minerals. The validity of the hypothesis is experimentally supported by the actual floatability, natural floatability, wettability, and adsorbability for neutral oils of coals, carbons, and hydrocarbon minerals tested. The combustible recovery of the flotation results, as used in this paper. was calculated from Eq. 1: P (100-Ep) 100 RWCP Rc= [1] F (100-E,) C, where R, is the percent combustible recovery; F and P are, respectively, the weight of feed and the weight of concentrate or product; E, and Ep are, respectively, the total percent of ash plus moisture in feed and in concentrate; Ru. is the percent weight recovery: and C, and C, are, respectively, the percent of combustible in feed and in concentrate. Except for ash and moisture content, all chemical components of a coal are assumed combustible. The experimental work included studies on flotation, ultimate and proximate analyses, contact angle tests, extractions of bitumen-A with benzene, adsorptions for liquid hydrocarbons, and wetting tests. Most of the flotation experiments were performed in a laboratory Fagergren machine; others were tested in a small Denver machine. The solid feed for the former was 300 g and for the latter was 30 g. The solid materials used for flotation were crushed to —48 mesh. After the mineral pulp in the flotation cell was agitated for 6 min and the pH was adjusted to 7.5 & 0.2 with sodium hydroxide or hydrochloric acid, a petroleum light oil having a viscosity of 5.73 centipoises at 77 °F was added and conditioned for 2 min. Finally, pine oil was introduced and the froth was collected for exactly 3 min. The weight ratio of petroleum light oil to pine oil was kept constant at 1.5 to 1. Tap water was used for all flotation tests. Contact angles were measured with a captive bubble machine. For each coal sample, three specimens were mounted in transoptic mounts and polished with levigated alumina, first on a sheet glass, then on a cloth-covered metal polishing wheel. The polished specimen was first washed with distilled water and wiped thoroughly on a cleaned linen pad, then transferred into the pyrex cell of the captive bubble machine and conditioned for 6 min., and finally measured for contact angles at three or more points. Except where otherwise stated, the induction time for each measurement was 1 min. The contact angle representing each material was obtained by averaging the measurements of three specimens. The linen pad was first washed with warm distilled water, then boiled 30 min in a 2N sodium hydroxide solution, and finally washed with distilled water until no trace of sodium hydroxide could be detected in the decanted solution. The cleaned linen pad was stored under distilled water. Immediately before using, the pad was rewashed and transferred into a clean pyrex petri dish partly filled with distilled water. The glassware and rubber gloves used were cleaned by soaking in sulphuric acid-potassium dichromate cleaning solution, followed by rinsing with distilled water. The polished specimens were handled only by glass forceps. The ultimate and proximate analyses were made in accordance with the ASTM standard procedures for coal and coke. The extractable bitumen-A was determined by weighing 1 g of —100 mesh sample and placing it in a desiccated and weighed ASTM aluminum-extraction thimble. The thimble was placed in condenser hooks and inserted into an extraction flask containing 100 cu cm of benzene. The flask was heated and the benzene vapor was condensed by water coils. At the end of 24 hr of percolation, the thimble was removed, desiccated, and weighed. Loss in weight of sample was taken as bitumen-A and calculated to dry and ash-free basis.

Jan 1, 1955

By Pual M. Tyler

BLIZKRIEG tactics in the present war have consumed metals on such a profligate scale that some of the best-laid procurement plans for civilian and military needs of even a year ago seem in retrospect incredibly meager. Conservation of raw materials has reached an all-time climax in Germany, where metals are worth more than human life and throwing away an empty toothpaste tube may be legally punished by death. Even the United States and the British Empire, proud masters of nine tenths of the world?s known mineral reserves and processing plants, are being driven to metals and feverishly expanding production facilities that not long ago were deemed overbuilt. After the war is over and inevitable postwar readjustments are completed, it is reasonable to expect that purchasing power ? or at least the ability to procure the comforts and luxuries of life ? will be distributed among vastly larger population than ever before, accelerating the rising trend in demand for industrial raw materials in ever greater quantity and variety.

Jan 1, 1942

By E. J. Whittenberger

OVER the past two decades, the Cr-Ni stainless steels, popularly termed 18-8 steels, have been used in ever increasing amounts in the aircraft, automotive, chemical, transportation, and building industries.' The contribution of nickel to these steels is associated with its strong austenite forming tendencies which assure good hot and cold forming characteristics, and with its beneficial influence upon corrosion resistance, especially in oxidizing acids. The adjustment of the chromium and nickel contents has been used advantageously in controlling the rollability and the response of the mechanical properties of these steels to cold reduction. With the advent of the jet age and the government stockpiling of nickel, considerable emphasis has been placed upon the development of satisfactory low nickel or nickel-free substitute austenitic stainless steels, especially for nonmilitary applications.2 Fer-ritic 17 pct Cr (AISI Type 430) stainless steel has been effectively substituted for the austenitic grades in applications with mildly corrosive exposure. However, the limited formability and ferromagnetic behavior of this grade do not permit its satisfactory use for many applications. To achieve better formability in a nenmagnetic steel and conserve nickel, a number of low nickel substitute austenitic grades of stainless steel have been developed in recent years. In most of these steels, manganese and nitrogen have been substituted for a portion of the nickel content, for example, 17 pct Cr-4 pct Ni-6 pct Mn (AISI Type 201), 18 pct Cr-5 pct Ni-8 pct Mn (AISI Type 202), and 16 pct Cr-1 pct Ni-17 pct Mn, all of which contain approximately 0.15 pct N.1 The precipitation of ferrite when large ingots of these Cr-Ni-Mn-N steels are heated to temperatures high enough for conversion to slabs on conventional universal slabbing mills has seriously affected the hot workability of these steels. This has been especially true in the case of the 16 pct Cr-1 pct Ni-17 pct Mn (sometimes referred to as 15 pct Cr-1 pct Ni-15 pct Mn) composition." Because it is possible that little, if any, nickel will be available for nonmilitary stainless steel applications in the event of a national emergency, a need has existed for a nickel-free austenitic stainless steel containing hot and cold forming characteristics similar to 18-8 steels and corrosion resistance at least comparable to the 17 pct Cr ferritic steel. The aforementioned deleterious effect of ferrite upon the hot working characteristics of the 16 pct Cr-1 pct Ni-17 pct Mn, steel indicates the importance of establishing the austenite-austenite plus ferrite phase boundaries as the first step in the development of nickel-free or low nickel substitute steels. This paper presents the data collected in an elevated temperature constitutional study of the Cr-Ni-Mn-N system at the South Works of the United States Steel Corp. Experimental Procedure The 300 compositions used in the investigation were melted in a 26 Ib induction furnace and cast in 3 14 in. diam by 18 in tall hot-tcpped ingot mo1ds.

Jan 1, 1958

By W. Tempelaar Lietz

The Ten Section oil field is located in the San Joaquin Valley in Kern County, California. about 12 miles southwest of Bakersfield in Township 30 South, Ranges 25 and 26 East. The accumulation is in a low relief anticlinal dome and has a productive area of approximately 2,200 acres. Discovered in 1936 as a result of seismic work, it was the first field on the floor of the Valley to obtain production. It had a small primary gas cap, and since its inception has been produced by depletion with controlled withdrawal from the gas cap to minimize blowthrough. STRUCTURE AND STRATIGRAPHY The Ten Section structure is an elongated anticlinal dome with flank dips of only about 7 degrees. A map of the field, now fully developed, and a composite log are shown in Figs. 1 and 2. Contours shown on the map are on the top of the first zone, or Marker XA as indicated on the composite log. As shown, the field has a productive closure of only some 350 feet, and there apparently is no faulting in the reservoir. The productive measures in Ten Section are of Upper Miocene age and are known as the Stevens sand. They contain thin, irregular shale or siltstone streaks which vary considerably in stratigraphic position and thickness and apparently are rather discontinuous. As a result, individual sands and shales cannot be correlated over any appreciable area, which makes it difficult to subdivide the sand body into separate zones which are distinct throughout the field. However, there are two fairly persistent siltstone bodies that at the time of development were considered to divide the productive measures into three - zones. The first, or uppermost zone is productive over the entire field and has an average thickness of 180 feet, of which some 65 per cent is sand. It had a primary. gas cap in the crestal area with an areal extent of 930 acres. The second zone has a productive area somewhat smaller than the first zone, but it did not have any original gas cap. It has an average thickness of about 360 feet, of which 55 per cent is sand. The third zone has a very limited areal extent and a maximum productive thickness of 100 feet, of which 80 per cent is sand. Recently, a deeper oil accumulation, termed the "53" sand, was discovered, but it is not discussed in this analysis. In the first and second zones the water table was at 7,980 feet subsea, while in the third zone it was at 8,080 feet subsea. RESERVOIR CHARACTERISTICS Sand Characteristics The Stevens sand in Ten Section is hard and well consolidated, and numerous wells were cored for core analysis. Core data on four representative wells are shown, plotted beside the electric logs in Figs. 3 to 6. The average porosity is 20 per cent, with porosities ranging from 15 to 30 per cent. It is estimated, from cores taken with oil base muds, that the interstitial water content is about 40 per cent. The average weighted permeability is approximately 140, with measured permeabilities ranging from 10 to 3,000 md. As might be expected with practically no correlation of individual sand

Jan 1, 1949

By W. Tempelaar Lietz

The Ten Section oil field is located in the San Joaquin Valley in Kern County, California. about 12 miles southwest of Bakersfield in Township 30 South, Ranges 25 and 26 East. The accumulation is in a low relief anticlinal dome and has a productive area of approximately 2,200 acres. Discovered in 1936 as a result of seismic work, it was the first field on the floor of the Valley to obtain production. It had a small primary gas cap, and since its inception has been produced by depletion with controlled withdrawal from the gas cap to minimize blowthrough. STRUCTURE AND STRATIGRAPHY The Ten Section structure is an elongated anticlinal dome with flank dips of only about 7 degrees. A map of the field, now fully developed, and a composite log are shown in Figs. 1 and 2. Contours shown on the map are on the top of the first zone, or Marker XA as indicated on the composite log. As shown, the field has a productive closure of only some 350 feet, and there apparently is no faulting in the reservoir. The productive measures in Ten Section are of Upper Miocene age and are known as the Stevens sand. They contain thin, irregular shale or siltstone streaks which vary considerably in stratigraphic position and thickness and apparently are rather discontinuous. As a result, individual sands and shales cannot be correlated over any appreciable area, which makes it difficult to subdivide the sand body into separate zones which are distinct throughout the field. However, there are two fairly persistent siltstone bodies that at the time of development were considered to divide the productive measures into three - zones. The first, or uppermost zone is productive over the entire field and has an average thickness of 180 feet, of which some 65 per cent is sand. It had a primary. gas cap in the crestal area with an areal extent of 930 acres. The second zone has a productive area somewhat smaller than the first zone, but it did not have any original gas cap. It has an average thickness of about 360 feet, of which 55 per cent is sand. The third zone has a very limited areal extent and a maximum productive thickness of 100 feet, of which 80 per cent is sand. Recently, a deeper oil accumulation, termed the "53" sand, was discovered, but it is not discussed in this analysis. In the first and second zones the water table was at 7,980 feet subsea, while in the third zone it was at 8,080 feet subsea. RESERVOIR CHARACTERISTICS Sand Characteristics The Stevens sand in Ten Section is hard and well consolidated, and numerous wells were cored for core analysis. Core data on four representative wells are shown, plotted beside the electric logs in Figs. 3 to 6. The average porosity is 20 per cent, with porosities ranging from 15 to 30 per cent. It is estimated, from cores taken with oil base muds, that the interstitial water content is about 40 per cent. The average weighted permeability is approximately 140, with measured permeabilities ranging from 10 to 3,000 md. As might be expected with practically no correlation of individual sand

Jan 1, 1949

By J. A. Botin, K. H. Singh

INTRODUCTION The Alfredo underground mine is one of the three mining operations of Rio Tinto Minera, S.A., all near the community of Rio Tinto in Huelva province of southwest Spain. The other two operations are Corta Atalaya open pit (Pyrite ore) and Cerro Colorado open pit (Copper ore 1. Underground mining of Alfredo Mine for pyrites started in the nineteenth century and continued without interruption until 1979 when it was discontinued due to economical reasons. In 1972, a new project was started for the mining of copper bearing ores on the footwall of the pyrite deposit. This copper ore is locally named “Cloritas” and it forms a nearly vertical and tabular shaped orebody which forms an envelope at the footwall of the San Dionisio pyrite orebody. Mining of the Cloritas commenced in 1975 using cut and fill stoping. In 1977, the original project was completely revised which led to the introduction of a bulk mining system to achieve a planned production of 3,000 tonnes of ore per day. This paper covers the economic and planning aspects of the mine and discusses the evolution of the mining method for the Cloritas orebody. A GENERAL DESCRIPTION OF THE CLORITAS OREBODY The “Masa San Dionisio” (figure 1 ) is a massive sulphide orebody located in the town of Rio Tinto, about 90 kilometres west of Sevilla, Spain. Extensive vein-type sulphide mineralization exists in the volcanic host rocks of the Masa San Dionisio. Within this area of stockwork veins, there is a higher concentration of copper in the form of chalcopyrite in a zone adjacent to and paralleling the contact with the massive sulphides. This copper envelope is locally referred to as the "Cloritas Orebody” and the ore within it is called "Cloritas”. The main zone of the Cloritas orebody, (figure 11, is tabular and nearly vertical having a length of 375-400 m east-west, a thickness of 20-50 m north-south, and a vertical extension of 500 m from the surface. In addition to this area, there is a second less important low grade area called zone 2A located to the north of the main zone below 26 Level which, in some sections, is not fully separated from the main zone. MINING METHODS Mining in Rio Tinto area can be traced back to the Phoenecians and the Romans. Modern day mining started with the demand for sulphuric acid during the last half of the nineteenth century. By 1971, more than 33 million tonnes of pyrite had been mined out of Alfredo Mine, (San Dionisio Orebody), using labor intensive drift and fill methods and also by open pit method. During the last decade, underground mining of the pyrite had become uneconomic due to lower prices and a slackening demand for pyrite, and the underground mining operations for pyrite were finally stopped in 1979. In 1971, a major change in the long range mining plans for Masa San Dionisio was established. Between 1971 and 1975, underground mining of pyrites was progressively reduced while open pit extraction was increased in

Jan 1, 1981

By R. S. Kinasevich, D. D. Crabtree, D. W. Fuerstenau, T. P. Meloy, A. L. Mular

The effect of such variables as feed size, particle shape, cleavage, and hardness on the relative proportion of impact, abrasion, and chipping events in a tumbling mill is demonstrated. The concept of an average event, which is a combination of the three comminution mechanisms, is introduced. It is postulated that the average event in a particular mill determines not only the size distribution but also the energy-size reduction relationship for the comminution process. Fragmentation of particles in tumbling mills appears to result from a combination of impact, abrasion, and chipping grinding.' The relative rates of size reduction attributable to any of the basic grinding mechanisms must depend upon a number of variables, such as feed size, particle shape, hardness, and the number and kind of particles in the mill. The purpose of this paper is to show experimentally how these variables in the properties of materials affect the size distributions obtained by grinding the material's in a laboratory tumbling mill. The resulting size distributions will be intetpreted in terms of a combination of three comminution mechanisms. METHODS AND MATERIALS In this study, minerals of widely differing properties were ground either separately or as mixtures in laboratory mills using rods or balls for grinding media. The materials used include quartz, Tuolomne, limestone (99.8% CaCO3), barite, corundum, galena, pyrite, glass beads, and crushed glass. The mill used was 8 in. in diam. and 9-1/4 in. long. For the ball milling tests, 17.6 kg of steel balls (36: 7/8 in. balls, 178: 1 in. balls, and 44: 1-1/8 to 1-1/4 in. balls) were used. For the rod milling experiments, 17.6 kg of steel rods 9-1/16 in. long (25: 5/8 in., 10: 3/4 in., and 5: 7/8 in. in diam.) were used. In each test, 1 kg of solids were ground wet at 60% solids at 77 rpm. In all cases except where otherwise specified, the feed to the mill was 4 x 8 mesh material. Size distributions of the ground products were determined by a wet-dry sieving procedure with Tyler series sieves. Size distributions of mixed products containing limestone were determined by dissolving the limestone with acid and sizing the residue. EXPERIMENTAL RESULTS AND DISCUSSION If the size distribution of the product from a tumbling mill depends upon the relative proportion of impact and attrition (abrasion and chipping) events, altering the grinding conditions may change these proportions and consequently alter the size distribution of the product. Data to illustrate this point can be taken from Gaudin's classic 1926 paper.2 In one series of experiments, Gaudin ground quartz of different initial sizes for four hours in a laboratory ball mill with 7/8-in. balls. In Fig. 1, his data are reproduced as the cumulative fraction finer than the stated size for the following initial feed sizes: 13.3 x 9.4 mm, 6.7 x 4.7 mm, 2.6 x 1.6 mm, and 0.83 x 0.59 mm. As the feed size was decreased, a dramatic change in the shape of the size distribution curves took place, even though the amount of minus 100-mesh

Jan 1, 1964

By R. B. Walker, R. Palmer, L. C. Bryner

The purpose of this investigation was to further study some of the factors affecting the air oxidation of sulfide minerals. Data obtained from laboratory studies on the effect of temperature, concentration of iron salts, pH, and other catalysts on the biological and nonbiological oxidation of sulfide minerals are presented. The oxidation of copper sulfide minerals and subsequent leaching of the soluble copper has long been a profitable operation. The chief oxidizing agent is oxygen from the air. This reaction is influenced by a number of different factors such as temperature, light, hydrogen ion concentration, oxidizing agents, and various catalysts. Sullivan1 found that copper sulfide minerals are slowly oxidized by the air and that dilute sulfuric acid and iron (111) increased their solubility. At that time it was not known that bacteria were involved in the oxidation of the sulfide minerals. It has been shown that pyrite, molybdenite, free sulfur, and the copper sulfide minerals found in the waste rock dumps in Bingham Canyon, Utah, are largely oxidized by chemosynthetic autotrophic microorganisms found in the leaching streams.2-6 Similar organisms have been isolated in other mining areas7,8 and from the effluents from coal rnines.9 The following are some of the questions that have arisen regarding the mechanisms of the reactions involved in the leaching process. How dependent is the leaching operation upon the biological reactions? How does the temperature effect the biological and non-biological reactions? How does the concentration of iron (II) and (111) effect the rate of oxidation of copper (II) sulfide? Does the iron act as a catalyst? Does activated carbon act as a catalyst on the oxidation of sulfide minerals? What effect does the hydrogen ion concentration (pH) have on the above reactions? The purpose of this paper is to report the results of laboratory studies on these problems. EXPERIMENTAL The apparatus used in this investigation was an air lift percolator described in our earlier work.' The percolator consisted essentially of an air lift which enabled the leaching solution and microorganisms to pass freely through a suspension of mineral (substrate) in Ottawa sand. The air lift served the additional purpose of maintaining an ample concentration of oxygen and carbon dioxide in the nutrient (leaching) solution. (See Fig. 1.) The percolators were so constructed that they could be immersed in liquid constant temperature baths for temperature studies. The thermostats were controlled to +0.5°C. The reactions were all run in the dark. The percolators were charged with one to three g of mineral, dispersed in 100 g of Ottawa sand and 100 ml of nutrient or leaching solution. The sand was purified to remove traces of iron by digesting with concentrated hydrochloric acid and washng with distilled water until free from chloride. After drying, the sand was ready for use. The compressed air supply was regulated to 5 psi and bubbled through an aerator containing distilled water, which was maintained at the same temperature as the bath used. The air was filtered through cotton plugs to maintain sterile conditions. The tops of the

Jan 1, 1968

By L. Bombardieri, H. F. Mills

IRON KING mine, producing gold-silver-lead-zinc ore, is 10 miles east of Prescott, Ariz. At present the 1806 level is being developed. The echelon pattern of ore deposit continues at depth but is less pronounced, and the orebody is now more or less continuous over 2600 ft of strike length. with widths 5 ft to as high as 26 ft where overlapping of lenses occurs in one section of the mine. Better continuity of ore at depth has encouraged systematic mining and improved plant facilities to offset higher operating costs. With favorable persistence of ore at depth. the three-compartment No. 6 hoisting shaft appeared inadequate to handle increased tonnage from greater depths, and in 1952, a four-compartment steel and concrete shaft was started. This is now at a depth of 1906 ft, and shaft pockets and loading cartridges are being installed on the 1806 level. Ore from the new shaft, hoisted in 51/2 -ton Jeto bottom dump skips, is dumped into a 500-ton shaft bin, from which it is fed to a 16x30-in. gyratory crusher and conveyed 415 ft through an undersurface concrete gallery to the secondary crusher and conveying system supplying the 900-ton mill. Lead, zinc, and pyrite concentrates are floated, and the flotation tailings are cyanided after desliming. Waste from the new shaft is dumped into a 250-ton surge bin, fed from this bin to a 24-in. conveyor, and discharged into the glory hole above the block cave. The new shaft is served by a double-drum 400-hp hoist used for ore and waste; the No. 6 shaft conveys men and material To secure a cheap source of waste fill for stoping operations, a block cave area was undercut In the hanging wall near the north end of the mine above the 600 level. Waste from the block cave is drawn from any of three large drawpoints on the 600 level, and a series of hanging wall transfer raises with controls and bypasses on each level provide a fast low-cost material for fill. The block cave is worked vertically through to surface in the form of a steep-sided hole 350x250 ft and several hundred feet deep, the sides of which cave and provide fill material without any blasting. Fill is a mixture of caliche-cemented surface gravel and small particles of hanging wall schist. Level Development: An orebody 300 times as long as it is wide requires a lot of development work. Former practice consisted of driving a haulage drift about 30 ft from the ore in an andesitic footwall, a drift on the ore, and crosscuts from the haulage drift at 100-ft intervals. Crosscuts are about 90 ft long. At present, only the odd numbered levels are so developed, and on the even numbered levels only the haulage drift and crosscuts are driven. Little or no timber is used for this development. This change resulted in 20 pct reduction of development costs and 50 pet reduction of square set stoping required for removal of floor pillars. Elimination of ore drifts on alternate levels leaves

Jan 1, 1957

By C. H. Samans, G. F. Tisinai, J. K. Stanley

The addition of nitrogen (0.10 to 0.20 pct) to Fe-Cr-Ni alloys of simulated commercial purity results in a real displacement of the u phase boundaries to higher chromium contents. The effect is small for the (Y + s)? boundary, but is pronounced for the (y + a +s)/(y + a) boundary. Although there is an indication of an exceptionally large shift of the n boundaries to higher chromium contents, especially in steels with nitrogen over 0.2 pct, the major portion of this apparent shift results from the fact that carbide and nitride precipitation cause "chromium impoverishment" of the matrices. The effect of combined additions of nitrogen and silicon to the Fe-Cr-Ni phase diagram is demonstrated also. Nitrogen can nullify the effect of about 1 pct Si in shifting the (y + o)/? phase boundary to lower values of chromium at all nickel levels from 8 to 20 pct. NItrogen can nullify this U-forming effect of about 2 pct Si at the 8 pct Ni level, but not at the 20 pct Ni level. The alloys studied were in both the cast and the wrought conditions. There are indications that the u phase forms more slowly in the cast alloys than in the wrought alloys if both are in the completely austenitic state. The presence of 6 ferrite in the cast alloys accelerates the formation of U. Cold working increases the rate of o formation in both cast and wrought alloys. THE major improvement in Fe-Cr-Ni austenitic alloys in recent years has been in the addition or removal of minor alloying elements to facilitate better control of corrosion resistance, sensitization, and heat resistance. One shortcoming of the austenitic Fe-Cr-Ni alloys, which never has been completely circumvented, is their propensity toward u formation. In the AISI-type 310 (25 pct Cr-20 pct Ni) and type 309 (25 pct Cr-12 pct Ni) steels, sufficient amounts of u phase can form, if service or treatment is in a suitable temperature range, to cause severe embrittlement. Also, there is a growing conviction that this phase may be contributory to some unexpected decreases in the corrosion resistance of certain of the 18 pct Cr-8 pct Ni-type steels. The present paper discusses the effect of nitrogen additions on the location of the (r+u)/d and the (y+a+u)/(y+a) phase boundaries in the ternary Fe-Cr-Ni system, for cast and wrought alloys of simulated commercial purity, and in similar alloys containing up to about 2.5 pct Si. The objective is to define compositional limits for alloys which will not be susceptible to u formation when used near 1200°F (650°C). An excellent review of the early studies of the u phase in the Fe-Cr-Ni system has been compiled by Foley.1 Rees, Burns, and Cook2 have determined a high purity phase diagram for the ternary system, whereas Nicholson, Samans, and Shortsleeve3 are- stricted themselves to a portion of the simulated commercial-purity phase diagram. Both groups of investigators show almost an identical position for the commercially significant (y+u)/y phase boundary. Further comparison of the work of the two groups indicates that, below the 8 pct Ni level, the commercial alloys have a decidedly greater propensity toward u formation than the high purity alloys. The two groups of workers agreed that both the AISI-type 310 (25 pct Cr-20 pct Ni) and the type 309 (25 pct Cr-12 pct Ni) steels are well within the (y+~) region and that the 18 pct Cr-8 pct Ni-type alloys straddle the U-forming phase boundaries. Nicholson et al.3 showed, in addition, that these boundaries shift toward lower chromium contents if greater than nominal amounts of silicon or molybdenum are added. The effect of nitrogen on the location of the s phase boundaries in the Fe-Cr-Ni system has not been known with any certainty. In 1942, an approach to this problem was made by Krainer and Leoville-Nowak,' but at that time they apparently were unaware of the slow rate of s formation in strain-free samples and aged their samples for insufficient times, e.g., 100 hr at 650°C (1200°F) and 800°C (1470°F). For this reason, it would be expected that their (y+ u) /y boundary would be shifted toward lower chromium contents (restricted ?-field) when equilibrium conditions were approximated more closely. Procedure for Studying the Alloys The alloys used were prepared in the following way: Heats of 200 lb each were melted in an induction furnace. A 5 lb portion of each heat was poured into a ladle containing an aluminum slug for de-

Jan 1, 1955

[James C. Gray, President W. B. Stephenson, President-Elect A. B. Cummins, Past-President E. G. Fox, Eastern Regional Vice-President H. C. Weed, Western Regional Vice-President Donald W. Scott, Central Regional Vice-President John Cameron Fox, Secretary 29 W. 39 Street New York 18, N. Y. After September 7, 1961 345 East 47 Street, New York 17, N. Y. D. R. Tone, Assistant Secretary Nathaniel Arbiter, Treasurer]

Jan 1, 1961

By Bieniawski, Z. T.

The importance of understanding the phenomena associated with rock fracture has long been fully appreciated in rock mechanics. This is clearly apparent from the special attention paid to rock fracture in the comprehensive papers published within the past four years. These papers present a picture of how the knowledge of brittle fracture of rock was gradually enriched and also show that what was often taken for granted three or four years ago is no longer considered as valid today.

Jan 1, 1972

By Oliver Bowles

AMONG mining men as well as in the popular mind the conviction has held sway that mining is pre-eminently a western industry. True it is that gold, silver, copper and other metals have made the States of California, Colorado, Montana, Utah. Nevada and Arizona famous. The prominence attained by these States as mineral producers is, however, not measured alone by the money value of the products of their mines. While the metals are without doubt indispensable in industry, the glamour of the precious metals, and the lure of copper, lead and zinc have given to their ore deposits a sentimental interest that often quite out-weighs their commercial importance. Today a great group of more commonplace minerals are finding a place in commerce and industry rivaling that of the metals, but there is little sentiment attached to them, and,. therefore, they attain relatively little publicity. This is the great group of the non-metallic minerals, exclusive of fuels and oils, including stone, sand and gravel, cement, lime, gypsum, asbestos, mica, phos-phate rock and many others. Almost unnoticed they have grown in production to almost unbelievable pro-portions. The estimated value of metal production for 1925 is given as $1,380,000,000, of the non-metals (ex-cluding fuels) $1,294,000,000. The non-metallic industries are not new, many of them date back almost to pre-historic times; but, as the greatest of them (on a tonnage basis) provides raw materials for the construction industries, it required the activities of the present age of construction to bring about their enormous development. Many of them enter manufacturing as well as con-struction. Non-metallic minerals constitute the back-bone of our great chemical industries. While construction and manufacture reach to all parts of the country their widest development has been in the great industrial centers of the eastern Seaboard and the middle West. Consequently the raw materials of mineral origin required for these great industries have attained a remarkable growth in the eastern half of the- United States. In compiling figures of mineral production for 1924, for which more complete data are available than for later years, the surprising fact is brought to light that the non-metallic mineral produc-tion alone of some of the eastern and middle-western States exceeds by a substantial margin the total min-eral production of some of the western States that have been classed as essentially mining States. Thus the non-metallic mineral production, exclusive of coal and petroleum, of the State of Ohio, was approximately $150,000,000; of Pennsylvania $175,000,000; and of New York $107,000,000. For the same year, 1924, the total mineral production of Utah was $84,357,000; of Montana $70,632,000; of Colorado $61,488,000; and of Nevada only $26,226,000. Even Minnesota, with its enormous iron ore production, reached only $107,845,-000, or a sum about equivalent to the non-metallic min-eral production of the State of New York.

Jan 8, 1927

By Henry D. Hibbard

A NOTED ordnance engineer once said to a friend, in speaking of the production of great steel guns, "How is it? We design our guns with a factor of safety of eight, and the guns burst." The vague way in which internal stresses and strains in iron and steel are often considered and spoken of makes it worth-while to examine them, as to their nature, their causes and results, how they may, for useful purposes, be advantageously dealt with, and how, when detrimental or dangerous, they may be reduced or kept within harmless proportions. Rankine defines ?strain " as a change of form or dimensions of a solid or liquid mass produced by a stress. This definition seems not intended to cover strains due to internal stresses, and it will help us in the present inquiry to consider strain as a tendency to change as well as an actual change of form. Internal strains in iron and steel are the result of stresses within the mass of the piece, some parts pulling and others pushing in resistance to them; or, in other words, some parts are in tension and some in compression, each part striving to relieve itself from strain and make the piece assume a form in which all parts are at rest. Subdivision, so that each part could relieve its strain by motion relative to the other parts, would, if carried out far enough, practically obliterate strain. The internal strains we are now to consider are not those due to the stresses of the service which the piece is rendering, either alone or as, a part of a structure, which may be termed service-strains, but those which originate or at least are contained in the piece itself. Internal stresses in a piece of metal are, like action and reaction, always equal and in opposite directions. The stresses

Sep 1, 1906

Executive J V W. REYNDERS, Chairman WILLIAM H. BASSETT E DEGOLYER H C BELLINGER RICHARD PETERS. JR. Finance H. A. GUESS GEORGE OTIS SMITH, Chairman F. JULIUS FONS Admissions GEORGE D. BARRON, Chairman DAVID LEVINGER P. A MOSMAN El K MASTERS J. A. SINGMASTIIR Alternates F. G. BREYER C W HAMILTON F. E PIERCE

Jan 1, 1923