Search Documents

By W. D. Robertson, D. A. Koss, A. J. Goldman

THE significance of the hcp (E) structure, which appears when Fe-Cr-Ni alloys (stainless steels) are transformed martensitically, has been the subject of considerable study and speculation.'-7 It has been proposed that the hcp structure is an intermediate phase in the transformation: fcc (austenite) — hcp (E) -bcc (0, martensite). However, recent studies by transmission electron microscopy6,7 have indicated that the hcp structure may be a consequence of the large shear strain (10 deg) associated with the fcc to bcc transformation. That is, the transformation to a bcc structure is accompanied by extensive dissociation of dislocations in the parent austenite, which has a low stacking-fault energy.'-'' X-ray diffraction analysis of the transformed alloy reveals a pattern of lines corresponding to an hcp structure, together with the parent austenite and the bcc product. The fact that the hcp structure is observed only in association with the bcc product in these alloys1'4'6'7 lends support to the conclusion that the hcp structure is a secondary product of the transformation. But, the evidence is circumstantial and more definite resolution of the two possibilities mains to be obtained. If the hcp structure is an intermediate product of the transformation, as in 1) above, then two distinct Ms temperatures should be observed, Ms and To evaluate this possibility, three different techniques that are particularly sensitive to the structural changes accompanying such transformations have been used in an attempt to detect two transformation temperatures in an Fe-15.1 Cr-11.7 Ni alloy: 1) high-sensitivity differential thermal analysis, 2) the temperature dependence of resonant frequency (elastic moduli), and 3) internal friction of cylindrical specimens vibrating in either longitudinal or torsional modes. To obtain the necessary sensitivity, a differential thermal analysis technique was developed for the purpose, Fig. 1. The differential temperature between a nickel standard and the specimen was amplified to produce a sensitivity of 0.02OC (0.7 v) in temperature difference. The specimen and the standard were surrounded by a copper block and the entire assembly was immersed in a solution of methyl and ethyl alcohol, freezing point, - 140OC, which provided the necessary thermal stability to reduce temperature fluctuations to negligible proportions. A cooling rate of about 1.5OC per min was obtained by bubbling liquid nitrogen through the liquid bath. In order to calibrate the experiment with respect to the evolution of heat in the transformation from fcc to hcp structures, differential cooling curves were obtained for an Fe-19.8 Mn alloy, which transforms martensitically to E.'"-' a Ms(e) temperature of 145°C was clearly defined by a temperature

Jan 1, 1964

By George Tryon, E. A. Barnard

The importance of the conservation of the waste heat contained in copper reverberatory furnace gases was realized very early by those in charge of operation at Anaconda. The first attempt to utilize it was in preheating the air used for combustion of the coal. This was done by forcing the air through ducts surrounding the flue-gas downtake and continued down beneath the furnace hearth to the firebox. Any small advantage gained by the heat transferred from the flue gases was more than offset by the losses sustained in cooling the hearth, therefore this process, after several trials, was soon discarded. It was first used at the Old Works as early as 1893 and again for a comparatively short time on the original furnaces at the Washoe smelter, or present works. Water-tube boilers came into general use very rapidly after 1890. Their adaptability for waste-heat steam generation, as well as the saving to be effected by the production of cheap steam from this source, was soon recognized. The first waste-heat boiler to be used in connection with a matte furnace at Anaconda was installed in September, 1900, at the "Old Lower Works." It consisted of a 100-hp. "Cook," vertical water-tube boiler. This boiler had 65 small perpendicular tubes arranged in concentric circles around a 10-in. tube in the center. These tubes were expanded into 4 ft. 4 in. inside diameter cylindrical steel top and bottom drums which served as the steam and mud drums respectively. This boiler was set in a cylindrical brick housing into which the furnace gases entered just above the mud drum and thence circulated upward around the tubes and steam drum to the stack. This installation proved unsatisfactory, presumably on account of difficulty with dust, and was soon abandoned. However, the possibilities for steam generation were undoubtedly encouraging for shortly afterwards (December, 1900) a 300-hp. Stirling boiler was installed, to be followed by two more in the spring of 1901. The choice of the Stirling type of boiler for application to copper reverberatory furnaces was particularly fortunate, as the arrangement of the tubes appears to combine to a great extent the maximum contact of the gases with the heating surfaces of the boiler and at the same time

Jan 1, 1934

By R. R. Knuckey

HAVING been associated with the operation of the de Vooys process for coal, which has treated 13,000,000 tons per annum, and recognizing the process as of value in ore sorting, Huntington, Heberlein and Co. Ltd. (Great Britain) in 1936 made an examination of all other existing methods. In none of the pioneer applications had recognition been given to the necessity for maintaining certain conditions that are essential for sorting certain ores if a truly efficient separation by gravity alone is to be assured. Consequently, in 1936-1937 Huntington, Heberlein and Co. Ltd., with Pearson, employing certain ideas connected with the de Vooys application, commenced the development of a separator that would allow conformance with optimum conditions in the zone where separation is effected. Later, Holt and Wade added to the value of the original application by Wuensch, Rakowsky and others, whose conceptions are being successfully operated today. Meantime, Trostler had enhanced the value of the original H-H. process by improvements that are now embodied in operating plants, and today the process incorporates an improved apparatus and a stable medium that produce the optimum conditions for separation. These conditions are: 1. Elimination of disturbing currents in the separating zone; 2. Reduction to a minimum of medium-density differences throughout. the separating zone; 3. Stable medium of minimum viscosity to permit the unretarded fall of mineralized particles; 4. Removal of products of separation with minimum disturbance to the separating zone. DESIGN OF SEPARATOR The H-H. sink-and-float separator consists of a pyramidal tank in which the separation actually takes place, connected at the bottom with an inclined bucket elevator. The tank and the elevator are filled with medium to within a few inches of the top of the tank. Medium is fed into the separator at a variety of points, according to the type of ore being treated, and it is withdrawn from the separator at two points: (1) together with the float product, by means of a variable-speed paddle, at the surface of the medium, and (2) by flowing over an adjustable weir cut in the side of the elevator casing. The prepared ore is fed onto the surface of the medium. The intermediate paddles, which revolve at a slow speed of 2 to 5 r.p.m., move the floating ore across the bath from feed end to float-discharge end. The ore, which is heavier than the medium, sinks below the sweep of the paddles and reaches the boot of the bucket elevator, which discharges it without disturbance of the separating zone. These arrangements for withdrawing medium from the separator allow the use of minimum flows, which connote minimum

Jan 1, 1943

By M. Van Siclen

THE outstanding fact in connection with dust disease in the United States at present is the growing recognition of its seriousness by state officials and by the more progressive operators of mining, metallurgical and allied industrial plants. The same may perhaps be said of labor in some of its better organized centers, but the average independent non-union workman continues, as of yore, to suffer the toll of disability and even of death from dust inhalation without realization of the source of his ill-being. Progress in the betterment of the handling of sufferers from dust disease and of the conditions creating dust hazards in mining and allied industries is pursuing a course similar to that of the now widespread campaign against accidents, in which the risk is more obvious, more severe, and was naturally recognized. sooner. The coming on of dust disease is generally relatively slow and its immediate effects not infre-quently masked by or attributed to other diseases. Marked exceptions to this general rule have occurred in districts where the dust is particularly pernicious, such as the Rand and Joplin; yet such exceptions, unhappy in themselves, opened the eyes of medical men, and of those in other localities charged with the responsibility for the welfare of industry, to the much more widespread if less spectacular hazard existing from the inhalation of dust in all rock-excavating operations and all industrial operations creating inorganic dust, whether it be crushing and grinding, sand-blast-ing, granite-cutting, or what not. Advancement to date in the United States in prevention and treat-ment has been slow, yet the record shows that quantitative methods for determining the degree of hazard and means for decreasing it were being developed as far back as 25 years ago; and that more rapid progress may be looked for from now on. In 1908, in this country, F. L Hoffman?(1) discussed the mortality from consumption in dusty trades, especially brass foundries; and in 1913 E. R. Hayhurst(2) described the effects of inhalation

Jan 1, 1933

By J. G. Savins

Analytical procedures are described for optimizing the selection of a rheological model when it is desired to express the functional relationship between true shearrate and shearing stress in analytical form. The procedures are extended to two principal model categories — "Generalized Newtonian" and "Viscoplastic" models. Graphical examples are presented to illustrate the utility of certain characteristic deriuative functions in distinguishing between these categories and in determining how well a particular model reflects the flow behavior of rheologically anomalous materials in simple shearing flows. INTRODUCTION Modern drilling fluids and fracturing fluids, being chemically complex, are frequently non-Newtonian — a peculiarity which complicates the solution of problems such as designing flowline and process equipment, and predicting laminar-turbulent behavior, solid-suspending ability and cutting-transport efficiency. Therefore, techniques of data analysis which accurately characterize the behavior of rheologically complex materials are needed for the accurate formulation of solutions of these and similar problems. It is the purpose of this paper to describe the application of a sensitive method of rheological data analysis — the dual differentiation-integration method of optimizing the selection of the functional relation between shear rate and shearing stress — to a variety of materials of interest in drilling and production practices. BASIC CONCEPTS THE DIFFERENTIATION METHOD To a first approximation, the viscosity function for a non-Newtonian system can be expressed in a form analogous to Newton's law of viscosity by the following generalization2.3 between the stress On introducing the restrictions that the system is incompressible and the motion is rectilinear, then l = 0 and l3 = 0 ; and with the further restriction that the flow is slip-free, the viscosity (an invariant) is then determined solely by 12. With this approach one can set up a suite of integral equations relating observed kinematical and dynamical parameters for certain types of flow experiments involving simple shearing motion, e.g., flow in a cylindrical tube, flow between rotating concentric cylinders, and flow between fixed parallel surfaces of large aspect ratio. Taken in the order cited, these integral equations are as follows.

Edmund Gybbon SpilsbURy, mining and metallurgical engineer of international reputation, died suddenly of heart failure on May 28, 1920, in the New York Eye and Ear Infirmary, following an operation for cataract, which had been successfully performed a few days before. Mr. Spilsbury was one of the early members of the American Institute of Mining Engineers, which he joined in 1873. During all this time he contributed freely of his time and ability. He was manager of the Institute from 1885 to 1887, vice-president, 1893 and 1894, and president in 1896. He was also a member of the Engineers Club, of which he was president in 1916 and 1917, American Society of Civil Engineers, American Society of Mechanical Engineers, Institution of Mining and Metallurgy, Mining and Metallurgical Society of America, American Electrochemical Society and the Rocky Mountain Club of New York. He was a trustee of the United Engineering Society from 1916 to his death; a member of United Engineering Society Library Board from its organization in 1913 until his death, being its chairman from 1918 to January, 1920; a trustee of Engineering Foundation Board from 1916 until his death; and member of the John Fritz Medal Board of Award. He was also a member of the Division of Engineering of the National Research Council. Born in London, England, in 1845, Mr. Spilsbury went to Liege, Belgium, at an early age, where he received his preliminary education. For his technical education he attended the University of Louvain, Belgium, graduating in 1862, and later he took a practical course at Clausthal, Germany. In 1864 he became assistant engineer for the Eschweiler Zinc Co., of Stolberg, one of the largest miners and smelters of lead and zinc in the world at that time, and the next year he took charge of that company's mines and works on the Island of Sardinia. From Sardinia he went to the Atlas Mountains in Morocco. In 1867 he entered the service of McClean & Stilman, of London, and had charge of the construction of the iron gates for the Surrey Commercial Docks. In 1868 he was designing engineer with J. Casper Harkort, and had charge of most of the detail work of the Keulenberg Bridge in Holland, the Danube Bridge in Vienna, and the Rhine Bridge at Düsseldorf. In 1870 Mr. Spilsbury came to the United States to investigate the lead and zinc resources for the Austro-Belgian Metallurgical Co. After spending two years in this work, he resigned in order to practice in the United States, and he was the first to introduce the Harz system of ore

Jan 1, 1922

By Reno H. Sales

The present-day application of geological knowledge to mine operations owes much to Survey activities. Early publications covering developed deposits at Comstock and Eureka in Nevada, and Leadville in Colorado, aroused great interest in mine geology among mine owners and operators. In later years personal contacts between Survey geologists, notably Lindgren, Spurr, Emmons, Weed, and Ransome, to name only a few, and mine managers, mine superintendents and mine foremen, brought directly home the importance of geological mapping and study in connection with mine operations. However, the Survey had recognized from the beginning that it was not practicable, either from the viewpoint of cost or policy, to supply direct help to the miner. The situation was met by many large mining companies through the organization of geological departments to deal with problems of geology which concerned not alone the every-day mine operation but also the life expectancy of the ore deposit. The mine owner therefore looked to the mine geologist to apply the "laws of ore deposition" in estimating the future of his mine. The examination of outside properties also became a duty of the company geologist where replacements were needed or where expansion of operations was contemplated. And finally, out of this situation there developed the independent consulting geologist, specializing in geological examinations of prospects, mines, and mining districts, whose duties included the highly important but often difficult task of appraising ore reserves and ore possibilities. Thus, while it may be considered by many that the work of the mine geologist overlaps that of the Survey geologist, their respective fields of endeavor are not in conflict. The appearance of the mine geologist has lessened in no manner the need of intensive field and research work by the Geological Survey and related organizations.

Jan 1, 1935

By J. H. Frye, C. P. Sun

A Frimary substitutional solid solution is a solution that has the same crystalline structure as the solvent metal, and in which solute atoms have replaced, solvent atoms at random on the host lattice. This replacement usually results in an increase in hardness as measured by conventional penetration tests. The factors controlling this hardness increase have been investigated in some detail for copper and silver alloys.1-5 It has been shown that at least four factors are involved: (1) concentration of solute, (2) row of the periodic table from which the solute is taken, (3) increase in lattice parameter of the solvent produced by the solute, and (4) work-hardening produced by penetration of the hardness indenter.2,4 The last factor is of the utmost importance. An investigation of the available data2,4 leads to the conclusion that the solutes that produce large hardness increases in copper or silver do so principally because they increase the rate of work-hardening. Furthermore, it is doubtful whether any solute produces appreciable hardening in the absence of plastic deformation and hence work-hardening. Thus it is clear that an understanding of the effect of solutes on rate of work-hardening is essential to an understanding of the hardness of solid solutions. This effect of solutes is also important in forming operations such as rolling or deep drawing. The presence of elements that confer rapid rates of work-hardening will increase power consumption and may well decrease the amount of deformation possible between anneals. This paper is the report of an investigation of the factors that control rates of work-hardening in copper and silver solid solutions. The silver and copper alloys considered are those in which all solutes are from the B subgroups or second short period of the periodic table. Experience with hardness, with structure of alloys, and with electrical conductivity has proved that results of a fundamental nature are most likely to be obtained if alloys are made up on the basis of the positions of the constituent elements in the periodic table. In previous work, Meyer analysis data on high-purity copper and silver solid solutions were obtained through careful measurements with fully calibrated equipment and these data were corrected to correspond to a standard grain size. From these corrected Meyer analysis data rates of work-hardening have now been calculated. Calculation of Rates as Work- HARDENING The Meyer analyses, on which this study of rates of work-hardening is based, consisted in determining impression

Jan 1, 1944

By Richard D. Mills

Throughout the mining industry, many companies perform sophisticated business and financial analyses of proposed capital investments. However, once the project is approved, it is never reevaluated. At best, there is an attempt to control capital costs and minimize overruns. The post-installation appraisal, a formalized review of investment performance, may prove helpful. Typical Project Review A typical capital investment is approved after business and financial benefits have been reviewed with management.* The financial data shown to management often include a net income statement, cash flow analysis and summary economic data similar to those shown in Table 1 overleaf. These financials report the expected impact of the project on the corporation financial statements. This project is a rudimentary example of a capital investment decision. An actual project would undergo a more sophisticated analysis incorporating depletion benefits, deferred taxes and a detailed cost breakdown. The example project has several financial benefits that could result in management approval. For example, it provides an immediate net income benefit to the company, generates positive cash flows every year of the project life and has a discounted cash flow rate of return of 25 percent. However, it also has the disadvantage of a long payback period. A sensitivity analysis would show which areas of the analysis have the greatest impacts on profitability. Post-Installation Program Objectives The post-installation appraisal goes beyond the analysis shown in Table 1 by comparing actual results to those projected in the original economic analysis. The post-installation program has three primary objectives: 1. To provide a periodic performance review of major spending programs. 2. To review decision-making and evaluation procedures. 3. To provide a means of controlling individual project investments. The first major function of the post-installation program is the periodic review of actual performance of projects and investment programs, identifying those factors which proved critical to the health of investments. This review will serve to keep management abreast of progress, provide a comparison of actual performance against expectations, and provide valuable information that can be used for improving future economics. The second major function of the program is to perform a continuous review of the decision-making process. This includes testing of evaluation procedures, forecasting techniques, and logic used in making decisions. An information system should be set up whereby original evaluations and historical performance data gathered under the appraisal program are documented for use by evaluators and management when assessing past and future investment proposals. Such data should be particularly useful in evaluating new and developing types of operations and in activities where companies repeatedly reinvest. The primary purpose of this feedback system is to sharpen estimates to assure that they are realistic and attainable. The appraisal program also provides assurance that consistent evaluation procedures are being used throughout a company, leading to improved procedures

Jan 1, 1985

By Reno H. Sales

The present-day application of geological knowledge to mine operations owes much to Survey activities. Early publications covering developed deposits at Comstock and Eureka in Nevada, and Leadville in Colorado, aroused great interest in mine geology among mine owners and operators. In later years personal contacts between Survey geologists, notably Lindgren, Spurr, Emmons, Weed, and Ransome, to name only a few, and mine managers, mine superintendents and mine foremen, brought directly home the importance of geological mapping and study in connection with mine operations. However, the Survey had recognized from the beginning that it was not practicable, either from the viewpoint of cost or policy, to supply direct help to the miner. The situation was met by many large mining companies through the organization of geological departments to deal with problems of geology which concerned not alone the every-day mine operation but also the life expectancy of the ore deposit. The mine owner therefore looked to the mine geologist to apply the "laws of ore deposition" in estimating the future of his mine. The examination of outside properties also became a duty of the company geologist where replacements were needed or where expansion of operations was contemplated. And finally, out of this situation there developed the independent consulting geologist, specializing in geological examinations of prospects, mines, and mining districts, whose duties included the highly important but often difficult task of appraising ore reserves and ore possibilities. Thus, while it may be considered by many that the work of the mine geologist overlaps that of the Survey geologist, their respective fields of endeavor are not in conflict. The appearance of the mine geologist has lessened in no manner the need of intensive field and research work by the Geological Survey and related organizations.

Jan 1, 1935

By Maurice Rey, H. Beavers

THROUGH circumstances connected with the war, the senior author lost his records, therefore it has been impossible to include numerical data in this paper. The arsenical quicksilver ore investigated had been roasted, with poor metallurgical results. The vapor-tension temperature curves of mercury and arsenious trioxide are similar, and the arsenical compound hampers the coalescence of mercury drops in the condenser and is the cause of large stack losses. The ore was a gray limestone carrying small amounts of carbon and mineralized with cinnabar and two arsenic minerals, realgar (As2S2) and arsenopyrite (FeAsS). The proportion of realgar often exceeded that of cinnabar; the proportion of arsenopyrite was smaller. The grade of the ore varied between 0.8 and 4 per cent Hg. The problem was to make a high-grade mercury concentrate, as free from arsenic as possible. The water used throughout the testing was hard, having a pH of about 8. FLOTATION OF REALGAR Realgar showed a very strong tendency to float. It formed a film at the surface of the pulp and floated in abundance with only pine oil. Therefore an attempt was made to float the realgar before the cinnabar, but this was not very successful; the percentage of mercury in the realgar concentrate could never be brought below 2 or 3 per cent. Cinnabar slimed easily and floated with pine oil, so that some of it always accompanied the realgar. There was also the question of the cinnabar-arsenopyrite separation. On further investigation it was found that realgar can be floated not only with pine oil but even better with a combination of hydrocarbons and pine oil. Washing the ore with ether revealed that it contained hydrocarbons, which helped to float the realgar. In this connection it belongs to the same class as carbon, sulphur and talc. It can be floated also with a xanthate, when activated by a heavy-metal salt. The conditions favoring the two types of flotation are opposed, as activation by a copper salt facilitates xanthate flotation (in fact, is even necessary to it), whereas it hinders pine oil and petroleum flotation. One type of flotation can be termed nonpolar and the other polar, a distinction that has been stressed in a previous paper.1 DEPRESSION OF REALGAR AND FLOTATION OF CINNABAR 'Many chemicals were tested in an attempt to float the cinnabar and depress the realgar. Finally starch rendered soluble with caustic soda was tried, also several grades of commercial soluble starch, and dextrin was found to be the best and the most convenient reagent. Several of these starch preparations have a strong flocculating effect on the pulp, which is a distinct disadvantage. Dextrin, with its low flocculating power, is excellent. It is noteworthy that starch preparations are also depressants for carbon and talc, so that the fact apparently has a general

Jan 1, 1941

By A. G. McGregor

In the Southwest a number of large steel chimneys discharge the gases from the copper smelting furnaces. Some of these chimneys show no deterioration after twenty years, others show serious deterioration after tour years service. A steel stack 20 ft. 7 1/2 in. (6.3 m.) in diameter by 279 ft. (85 m.) high, Fig. 1, used for roaster gases only at the Calumet & Arizona Mining CO.'s plant at Douglas, Ariz., was lined to the top of the bell, 40 ft. (12 m.) from the base, with common brick placed on end, lime and cement mortar being used. Above the bell, the stack was lined with 4 by 4 by 8 in. (10 by 10 by 20 cm.) building tile, placed on end, making a lining 4 in. thick. The tiles were supported on angle-iron rings, riveted to the inside of the chimney shell about 15 ft. apart. The chimney was put into use in the latter part of 1913. Four years later, considerable of the tile lining had fallen out of place and mixed with the flue dust at the bottom of the chimney. About a year later, several flattened and distorted sheets were noticed about 70 ft. below the top. An investigation showed that the thickness of these distorted sheets, which was originally 1/4in., had been reduced one half. One year later, or six years after the chimney went into use, several holes, a square foot and smaller in area, appeared near the flat spots mentioned. Soon afterwards, when the chimney was shut down for repairs, it was found that most of the tile lining for 125 ft, from the top had fallen out and that the steel shell was badly corroded; but where the lining remained in place the shell was undamaged. Many of the tile which had fallen out of place had become soft or flaky and crumbling, others were as hard as when placed. An analysis of the hard and soft tile is shown on p. 2. These tile were of a fireclay mixture, and were used instead of common brick on account of lower cost. The steel forming the upper 125 ft. (38 m.) was replaced, and a 4 1/4-in. (11-cm.) lining of firebrick was laid from the bell to the top of the chimney. The brick were placed on end, wedges and keys being used. After each 8-in. course was set, keyed, and wedged tight, thin mortar —water, sodium silicate, and finely ground silica—was worked into the joints. The brick are supported on angle-iron rings, every 15 ft., in the same way as the tile.

Jan 1, 1921

By R. L. Rickett, W. C. Leslie

The influence of deoxidation practice, prior thermal history, and aging time and temperature on the strain-aging behavior of low-carbon open-hearth steels was investigated. The criterion of aging employed was the increase in yield strength in the tensile test, after straining and aging. Composition, prior heat treatment, and aging conditions were all found to be important in governing the strain-aging characteristics of these steels. THAT deoxidation changes the strain-aging propensities of low-carbon steels has been known for a long time, but there has been little agreement, and even contradiction, between results obtained by different investigators and between results obtained in the laboratory and in the mill. This investigation was begun in the hope that some of the uncertainties connected with the strain aging of commercial steels could be eliminated. In considering this problem, it was necessary to define strain aging and to examine the methods used to measure this property. Strain aging can be defined as the changes in properties of a metal or alloy with time, after cold working. The rate at which these changes occur increases as the temperature is raised above atmospheric. The requisite plastic strain is the principal distinction between strain aging and quench aging, the latter being due to precipitation from supersaturated solid solution. Strain aging is also characterized by rapid attainment of maximum hardness at high aging temperatures and lack of softening (overaging) at low aging temperatures. Several possible criteria of strain aging have been listed by Sachsl and by Davenport and Bain.' Because changes in mechanical properties are the most easily measured and the most commonly used, consideration of methods to be used in this investigation was confined to three tests: tensile, notch-impact, and hardness. Hardness tests are the most economical and easiest to perform, but produce only one measure of strain aging. Also, as pointed out by Felmly, Hartbower, and Pellini,³ hardness changes due to aging are not pronounced for steels containing more than 0.15 pct C. Notch-impact tests require careful preparation of large numbers of specimens. Above and below the transition temperature the test lacks sensitivity; furthermore, it is extremely difficult to impart a uniform strain to the specimens, followed quickly by aging and final testing; machining must generally take place after straining. For these reasons, the tensile test was selected for use. Although this test requires a considerable expenditure of time, labor, and money in preparation of the specimens and performance of the test, more information can be gained than from any other single mechanical test, information which includes upper and lower yield points, yield-point elongation, tensile strength, strain-hardening exponent, reduction of area, and elongation. Low and Gensamer' and Schwartzbart and Low5 lso used the tensile test, taking the increase in flow stress after straining in tension and aging as a measure of strain aging. In our work, as in theirs, each specimen was strained an arbitrary amount, sufficient to pass through the

Jan 1, 1954

For his achievement in building the Panama Canal, Major-Gen. George W. Goethals was presented, on May 22, the John Fritz medal, the highest mark of distinction in the engineering profession. In the absence, in Europe, of Clemens Herschel, chairman of the Board of Award, Charles F. Rand presided over the meeting. Col. John J. Carty, who was chairman of the Board of Award at the time the medal was awarded to Gen. Goethals, and who ordinarily would have presented the medal, was detained in Paris by Government work, so the presentation was made by Ambrose Swasey. When calling the assembly to order, the Chairman said: This medal has been awarded by a Board representing four of the National Engineering Societies: American Institute of Mining and Metallurgical Engineers, American Society of Civil Engineers, American Society of Mechanical Engineers, and American Institute of Electrical Engineers. The medal was established in 1902, in honor of that great American engineer, John Fritz, and has never been awarded except to very distinguished men. In. 1902, the first award was made to John Fritz for scientific and industrial achievement. In 1905, to Lord Kelvin for his work in cable telegraphy and other scientific attainments. In 1906, to George Westinghouse for the invention and development of the air brake. In 1907, to Alexander Graham Bell for the invention and introduction of the telephone. In 1908, to Thomas A. Edison for the invention of the duplex and quadruplex telegraph, the phonograph, the development of a commercially practical incandescent lamp, the development of a complete system of electric lighting, including dynamos, regulating devices, underground system protective devices and meters. In 1909, to Charles T. Porter for his work in advancing the knowledge of steam engineering and in improvements in engine construction. In 1910, to Alfred Noble for notable achievements as a civil engineer. In 1911, to Sir William H. White for notable achievements in naval architecture. In 1912, to Robert W. Hunt for his contributions to the early development of the Bessemer process. In 1914, to Professor John E. Sweet for his achievements in machine design. In 1915, to Dr. James Douglas for notable achievement in mining, metallurgy, education, and industrial welfare. In 1916, to Dr. Elihu Thomson for achievement in electrical invention, in electrical engineering and industrial development, and in scientific research. In. 1917, to Dr. Henry M. Howe for his investigations in metallurgy, especially in the metallography of iron and steel. In 1918, to J. Waldo Smith for achievement as engineer in providing the City of New York with a supply of water. And now to General Goethals for achievement as the builder of the Panama Canal_

Jan 7, 1919

By J. R. Coulter, F. O. Case, H. G. Satterthwaite, B. Harden

During the two years that the Henderson plant has been in operation, a number of technical improvements have been made by the staff of Basic Magnesium, Inc., the effects of which were realized subsequent to the writing of the paper by Major C. J. P. Ball (p. 28j, this volume). Pellet Mix The process as originally installed required the use of peat moss in the mixture going to the chlorinators. This had to be imported from Canada at a considerable cost, and, besides being expensive, constituted a serious fire hazard in the dry climate of Nevada. Experimentation looking toward its elimination had been going on for some time and was actively pushed as soon as operations commenced. It was found that a pellet mix containing no peat, which would chlorinate at a satisfactory rate, could be cast as a fluid slurry, which would set up into a hard mass having the desired porosity. For carrying out this operation, equipment similar to that used in the manufacture of phosphate fertilizer at Anaconda, Mont., was installed and proved eminently successful. The dry materials, with peat moss and raw concentrates entirely eliminated, are mixed with magnesium chloride solution in two Pratt phosphate mixers and the resultant slurry is poured onto two 48-in. slowly moving rubber conveyor belts. By the time the slurry has reached the head pulley, the material has set su4iciently to be broken and sized as desired. The discharge from the casting belts is fed to the four rotary kilns in the preparation plant, where it is dried and coked to the proper degree for subsequent chlorination. With the peatless feed the capacity of the kilns was found to be about double what it had been before, so that the four rotaries suffice for a 10-unit operation, thus making it unnecessary to operate the extruders and tunnel kilns. In addition to saving the cost of the peat, the new system can be operated with about 85 per cent less labor than was formerly required in the preparation plant. The new pellet production system has also made it feasible to install centralized crushing equipment with suitable conveyors and a loading station. Containers of 8000 lb. capacity were substituted for small cubicles of 1000 lb. capacity which formerly were used for charging the chlorinators, and trailer trucks were substituted for the small trains originally provided for transportation from the preparation plant to the chlorinators. These changes resulted in a considerable saving in handling and transportation charges. Handling Molten Metal The molten magnesium originally was ladled from the electrolytic cells into small gas-fired brick-lined cars standing between the cell rows. From these cars the metal nes ium. into ''cheeses'' weighing from 150 to 300 lb. After solidification the

Jan 1, 1944

As described in the section on the Palabora twin crushers, the Palabora ore consists of two types: a carbonatite containing a low titanium magnetite, and a foskorite containing high titanium magnetite. As the Palabora pit was widened and deepened, more and more of the foskorite had to be mined. The 25,000 mt expansion of the Palabora plant which went into operation in early 1977 therefore takes its feed from the foskorite section of the orebody. For the expansion, a third 54 in. by 74 in. gyratory crusher was installed to crush feed for two 32 ft by 15 ft (9.75 by 4.6 m), 9000 hp (6710 kw) autogenous single -stage grinding mills. These units are located near the two existing primary crushers, and the ground ore is pumped 5277 ft (1640 m) to the expanded flotation plant by five stages of centrifugal pumps. The new gyratory is installed in a unique Figure-8 shaped enclosure with the crusher in the smaller 27 ft 11 in. (8. 5 m) diameter cylinder and the maintenance area in the 36 ft 1 in. (11 m) diameter cylinder. Cylinder walls are only 23.6 in. (600 mm) thick because their circular design permits all the concrete to be in compression. A rectangular dump pocket which sits on the smaller cylinder contains two manganese steel faced splitters to protect the crusher spider and countersunk water spray headers under the dumping positions for dust suppression. The dump pocket holds 330 st or 300 mt and is also lined with manganese steel. The crusher is mounted on a reinforced concrete diaphragm over the 363 st (400 mt) crushed ore pocket. In the back of the pocket is plastic pipe. Radioactive level control sources are lowered into this pipe from the crusher support floor. The pipe is protected by concrete covered with steel castings. Level control detectors are mounted on the front wall of the pocket. Liner plates on the crushed ore pocket walls are removed and in- stalled by the use of a circular monorail and trolley mounted on the pocket ceiling. The door in the front of the crushed ore pocket is hinged at the top rather than at the sides and is raised by an electric winch. For removal of the eccentric, rails are installed in the pocket and a unique hydraulically operated cart is moved under the eccentric. A platform is raised to receive the eccentric and lowered so that it may be removed. Crushed ore is removed from the pocket by a hydraulically powered, 8 ft

Jan 1, 1978

By L. J. Demer, W. W. Walker

AMONG several variables of the indentation hardness test is the effect of loading time on the measured hardness of a material. The most generally recommended duration of loading is 10sec.1-3 Although this short loading duration is undoubtedly satisfactory for harder metals, it is questionable that it is sufficient for very soft metals,4 or for certain plastics.5 The effect of duration of loading on the measured hardness of ionic crystals is largely unknown, although Onitsche and Mitsches found that the indentor (under a very low load) had not yet reached equilibrium after 60 sec in a variety of ionic crystals. To extend further the data of Onitsche and Mitsche, a systematic study was made of the effect of duration of loading for longer periods, up to 50,000 sec, on the 136 deg Dph of synthetic lithium fluoride. For comparison, less extensive tests were made on synthetic magnesium oxide and copper single crystals. The general procedure used was to indent a cleaved and polished (100) face of a lithium fluoride crystal using a Leitz Durimet microhardness tester. In certain cases, the indentor was so oriented as to align the diagonals of the 136 deg diamond pyramid indentation parallel to a (100) edge. In other cases the diagonal of the indentation was aligned at 45 deg to a (100) edge of the crystal. After indenting, the surface tested was etched in the acid etchant recommended by Gilman and Johnston.' This revealed the position of dislocation lines which intersected the surface tested. At these points of emergence were formed the usual sharp, pyramidal etch pits as shown in Fig. 1. The specific procedure used in studying duration of loading was as follows. The surface of the crystal was indented, and the load was left on the indentor for a predetermined time. This duration of loading was varied systematically from 1 to 50,000 sec. After the desired amount of time had elapsed, the indentor was removed from the crystal and the size of the resulting indentation was determined using a micrometer eyepiece. The surface was then etched to reveal the dislocation etch pit pattern around the indentation. Procedures used for lithium fluoride, magnesium oxide, and copper were similar. Preliminary studies revealed that, although an indentation was enlarged by increasing loading time, no corresponding changes occurred in the surface etch pit pattern. Since no evidence of dislocation movement was observed on the surface, it was assumed that the plastic deformation indicated by the indentor sinking into the surface was a result of dislocation movement inside the crystal. This movement was studied bf making a series of surface indentations in a crystal corresponding to various lengths of time, cleaving the crystal vertically through the indentations, etching the freshly

Jan 1, 1964

By Lucien Eaton

THE accuracy with which detachable bits can be sharpened and gauged by grinding has made possible refinements in design that cannot be attained by forging. This applies particularly to gauging, where accuracy is of the greatest importance. Gauge changes of 1/32 in., and even 1/16 in., are now feasible, whereas 1/16 -in. changes are about the limit in accuracy for forged bits. These small changes in gauge are feasible, however, only with certain fundamental principles of design. Within reasonable limits the depth to which a hole can be drilled is dependent primarily upon the loss in gauge, or diameter, of the bit. In drilling there is always a certain amount of " overdrilling "-the bouncing of the bit in the hole and its rotation wear away the walls-so that the actual diameter of the hole is greater than the diameter of the bit. The amount of this overdrilling depends upon the kind of rock being drilled, and is sometimes sufficient to permit the use of the same diameter of bit for the full depth of the hole. If, for instance, a 1 ¾ -in. diameter bit overdrills 1/32 in. in diameter, and loses 1/64 in. in gauge in drilling 2 ft. of hole, the bottom of the hole is still 1/64 in. larger than the original diameter of the bit, and a new 1 3/4-in. bit can be used to drill the next 2 ft. If, however, the overdrill is less than the loss in gauge, the next bit must be of smaller diameter. The first requisite in reducing loss of gauge in drilling is to have the points and corners of the wings of the bit cut circles of the same diameter, thus producing a reaming surface with continuous bearing on the wall of the hole. The greater the reaming surface, the less the gauge loss that is to be expected. If the reaming surface, however, is too large, it may impede the rotation of the bit through excessive friction. This principle was probably first recognized in the design of the Carr bit (Fig. 1)) a bit with a single cutting edge of wide angle, a definite reaming edge, and a large center hole. The same idea was followed in designing the double-taper cross bits, which are now standard almost everywhere Fig. 2 illustrates a typical double-taper cross bit. The taper from the point of the wing A to a little behind the corner B is 5° and from

Jan 1, 1939

By J. H. Frye, C. P. Sun

A Frimary substitutional solid solution is a solution that has the same crystalline structure as the solvent metal, and in which solute atoms have replaced, solvent atoms at random on the host lattice. This replacement usually results in an increase in hardness as measured by conventional penetration tests. The factors controlling this hardness increase have been investigated in some detail for copper and silver alloys.1-5 It has been shown that at least four factors are involved: (1) concentration of solute, (2) row of the periodic table from which the solute is taken, (3) increase in lattice parameter of the solvent produced by the solute, and (4) work-hardening produced by penetration of the hardness indenter.2,4 The last factor is of the utmost importance. An investigation of the available data2,4 leads to the conclusion that the solutes that produce large hardness increases in copper or silver do so principally because they increase the rate of work-hardening. Furthermore, it is doubtful whether any solute produces appreciable hardening in the absence of plastic deformation and hence work-hardening. Thus it is clear that an understanding of the effect of solutes on rate of work-hardening is essential to an understanding of the hardness of solid solutions. This effect of solutes is also important in forming operations such as rolling or deep drawing. The presence of elements that confer rapid rates of work-hardening will increase power consumption and may well decrease the amount of deformation possible between anneals. This paper is the report of an investigation of the factors that control rates of work-hardening in copper and silver solid solutions. The silver and copper alloys considered are those in which all solutes are from the B subgroups or second short period of the periodic table. Experience with hardness, with structure of alloys, and with electrical conductivity has proved that results of a fundamental nature are most likely to be obtained if alloys are made up on the basis of the positions of the constituent elements in the periodic table. In previous work, Meyer analysis data on high-purity copper and silver solid solutions were obtained through careful measurements with fully calibrated equipment and these data were corrected to correspond to a standard grain size. From these corrected Meyer analysis data rates of work-hardening have now been calculated. Calculation of Rates as Work- HARDENING The Meyer analyses, on which this study of rates of work-hardening is based, consisted in determining impression

Jan 1, 1944

By F. R. Cattoir, R. W. Kimball, C. T. Anderson, V. V. Donaldson

THIS paper is the second of a series on the effect of various elements on hot-working characteristics of Fe-C alloys to be issued by this laboratory. The investigations being conducted at the Ferroalloy Research Branch of the U.S. Bureau of Mines, Redding, Calif., involve fundamental research on the effects of various alloying materials and impurities on the physical properties of high purity Fe-C alloys. This paper deals with the determination of the limit of forgeability of steels containing varying amounts of manganese and sulphur. A paper discussing the hot-working characteristics and the physical properties of the forgeable alloys is being prepared. One of the principal impurities in all steels is sulphur.. The phenomenon, hot-shortness, commonly attributed to sulphur, has long been a source of expense and inconvenience to both the maker and user of steels. In steelmaking practice, this effect of sulphur has been overcome by the addition of manganese which, apparently, acts as a desulphurizer. Manganese is also used as a deoxidizer and alloying material. The critical and strategic position of man- ganese gives added importance to research which may contribute to its conservation and more effective utilization. It is not the purpose or intention in the present paper to give any explanation of the mechanism of either hot-shortness or its prevention but rather to report the results of forging high purity Fe-C alloys of the range of compositions near the limit of hot-forgeability. Temperatures for each phase of reduction were duplicated within 20" to 30°F for all tests. The starting material was sponge iron, which, after melting and purification, gave a high purity iron containing about 0.001 pct each of silicon and phosphorus. Scrap iron was not considered suitable because of its high percentage of contaminants and wide variation in analyses. The sponge iron was melted and refined for melting stock in a three-phase, direct-arc, size ST, Moore Rapid Lectromelt furnace with a 500 kva rating as described in the preceding paper. Additives were carefully selected to avoid addition of contaminants. The sulphur was added as resublimed flowers of sulphur or purified roll sulphur of analytical grade. The manganese used was dehydrogenated high purity electrolytic material produced by the Bureau of Mines plant at Boulder City, Nev. High purity aluminum in the form of wire was used for deoxidation. The limestone was obtained locally and had the following analysis: CaO, 53.7 pct; MgO, 0.8; ignition loss, 42.4; R2O3, 0.2; SiO2,3.0; and P2O5, 0.014.

Jan 1, 1955