Search Documents

By S. J. Im

Bupyung Silver Mines daily treats average 14 tons of concentrates containing 9,000 g Ag per ton. Bupyung Silver Refinery uses Merrill Crowe process to recover the silver from the leach solution containing 1.0 g/l Ag; Series of experiments were carried out to recover the silver from the solution by means of direct electrowinning in place of Merrill Crowe process. The recovery of the silver was 99% when the cell voltage and the retention time were 1.9 v and 3.0 hours, respectively. Power consumption was 3.2 Kwh/kg of Ag. It was found that impurity buildup was not significant during the recycling. The direct operating cost for the electrowinning was evaluated to be $ 0.35/kg of Ag.

Jan 1, 1984

By A. C. Bluemel, J. S. Harper, J. H. Jett

Can the mining industry in the United States accept the change and challenge of the "Now Generation" of an entirely new high-performance automated transportation system? Advanced transportation systems for the mining industry can be defined as those which lend themselves to automation and meet definite performance and cost objectives. The term automation shall mean that control of transportation system is accomplished by a closed loop electronic circuit which, when started on command, will continue to cycle as programmed until such time as an intelligent feed-back causes the system to shut down.

Jan 1, 1970

By P. L. De Bruyn

The behavior of collectors at the mineral-solution interfaces is usually explained in terms of an ionic adsorption process. Through the distribution of collector ions between the solid surface and the co-existing solution phase the mineral is believed to acquire a water-repellent surface coating. Quantitative adsorption studies have been made on simple flotation systems only within the last few years. Such investigations were made possible by the adoption of the radiotracer method of analysis. As a consequence of these studies a new parameter has been added to aid the understanding of the flotation process.

Jan 3, 1955

By C. A. Sobotowski, J. Eagan

Computer programs applicable to coal mining have been available for some time, especially in the academic sector. However, the computer has not routinely been applied to actual mining operations. This paper discusses how a computer system was set up as an important tool in mining design and decision making. The project was completed within the allotted timeframe of two months by taking advantage of existing technology. Key points include the selection of programs to meet the specified needs of the project, conversion of the programs to be compatible with a computer of a different manufacture, simplification of the data entry process, development of procedures for using these programs, and an explanation of how the reports generated from the programs were used for mine planning and decision making.

Jan 1, 1983

By Roy E. Gilbert

IN what ways can conventional geophysical methods be used in the search for quartz-sulphide veins covered by several feet of overburden? The New Park Mining Co., in search of an answer to this question, empirically tested simple geochemical, electrical, and magnetic methods over known ore bodies and geologic structures. Geochemical methods were the only ones found to be applicable to direct ore search. Indirect uses were found for electrical and magnetic tests. Experiments were conducted in the southeastern part of the Park City mining district. Ore in this part of the district is found principally in steeply dipping veins which are localized along faults and fractures that cut Paleozoic sediments and quartz diorite intrusives. Extensive soil cover effiectively hides both veins and country rock. The type of vein most likely to

Jan 1, 1953

By W. A. Boyer

Mine hoisting ropes can be loaded to capacity only when the strength of each component is exactly known. Characteristic curves provide this information. When load and rate of acceleration are specified for an individual rope, the characteristic curve assumes a predetermined shape. The factor of safety is the value derived by dividing the breaking strength of the rope by the total stress on the rope where it goes over the sheave wheel. Total stress is made up of the weight of skip and cage, weight of ore, weight of rope between sheave and rope clevise or attachment, friction load, and acceleration force. Bending stresses are neglected in this discussion, as sheaves and drum diameters are assumed to be large enough to reduce these stresses to a negligible value.

Mar 1, 1956

New Device Eliminates Blasting in Coal A non-explosive device developed by duPont utilizes the high pressure of a gas generated inside a steel tube which is inserted in a hole drilled in a coal seam to break down the face of coal. Chemical reaction is started by an electric current which produces heat to initiate the action. The same heat destroys the starter wire as soon as electric current is no longer needed. The tube containing the chemical is closed at the outer end by a plug with electrical connections, and at the other with a disk that is ruptured by the compressed gases formed. When the gas has been liberated in sufficient quantities to create a desired pressure the disk breaks and the released gas breaks down the coal face. The new device is called a Chemechol.

Jan 10, 1951

By W. L. Staker

The Bureau of Mines investigated selective extraction of Au and Ag from a low-grade Au ore containing Hg. Gold and silver were extracted from the ore in cyanide slurries, and Hg extraction was suppressed with sodium or calcium sulfide. Maximum Au extraction and minimum Hg extraction were obtained using solutions containing 0.34 lb NaCN/ton of solution. Increasing the cyanide concentration increased Hg extraction without increasing Au extraction. Mercury extraction from the ore was suppressed with 0.5 to 2.9 lb CaS/lb Hg in the ore. Gold-to-mercury ratios of 100:l to 400:l were obtained in the leach solution, and on the activated carbon in a CIP circuit.

Jan 1, 1984

By H. A. Burgman

During in situ uranium mining using ammonium bicarbonate lixiviant, the ammonium exchanges with cations on the ore's clay. After mining is complete, the ammonium may desorb into post-leach ground water. For the particular ore studied, other elements (uranium and selenium) that are mobilized during the leaching process, have also been found in post-leach ground water. Laboratory column tests, used to simulate the leaching process, have shown that aluminum chloride can rapidly remove ammonium from the ore and, thus, greatly reduce the subsequent ammonium leakage level into ground water. The aluminum chloride has also been found to reduce the leakage levels of uranium and selenium. In addition, the aluminum chloride treatment produces a rapid increase in permeability.

Jan 1, 1985

Jan 1, 1941

By H. T. Lundberg, J. H. Ratcliffe

In airborne gravity surveys effects of acceleration and irregular movements of the aircraft must be balanced out or overcome. The gradient of vertical gravity is recorded, therefore, by using two masses instead of one. As the amplitude variations are infinitesimal and difficult to measure accurately, at present it is enough to determine whether variation of gradient during flight is positive or negative. The positive portions of the pattern can then be indicated and contoured. Even with these simplifications, the source of energy must be exceptionally stable. General Principles: In the conventional gravi-meter the weight of a standard mass is determined at a number of selected points within the survey area. In most systems weight is determined by comparing the gravity pull with extension or torque

Jan 1, 1960

By I. A. Lange, A. M. Richardson

Although methods for determining shaft lining thickness are well documented, little attention has been given to the design of station breakouts and other related shaft ground support structures. This paper discusses design of selected shaft structures for the Cathedral Bluffs project, a planned 54-kt/d (60,000-stpd) oil shale mine in western Colorado. Design philosophy and construction sequences used in the three completed 520-m (1700 ft) deep, 4.6-m (15 ft) to 10.4-m (34-ft) diameter shafts are described.

Jan 1, 1984

By Ian M. Thomson, Robert W. Greene

Last August, American Commercial Barge Line Co. (ACBL) began moving coal from mines on the old Camp Breckinridge property in Western Kentucky to TVA's new 2600 MW steam plant at Cumberland City, Tenn. By April of 1973, this movement will reach a level of 7 million tpy. TVA bought the coal rights to this property from the General Services Administration in 1965 for approximately $7 million and is now in possession of reserves containing about 120 million tons of recoverable No. 9 coal, and about the same recoverable amount of No. 11 coal. TVA then contracted through competitive bidding with Peabody Coal Co. to mine the No. 9 seam through two slope shafts. The mines are about 300-ft deep and are separated by the one major fault on this property. The mine portals are approximately 3 ½ mi apart, with the northern portal being over nine miles distant from the Ohio River.

Jan 1, 1971

By R. E. Mazurak, E. L. Ealy

At the Beckley mine in southern West Virginia, forecasting unstable roof conditions in advance of mining is accomplished by wing a rating system that combines historical information on mine roof failures with known mine geology. Failure frequency rates are derived for each category of roof rock composition, unit thickness, structure, and extraction ratio. In this manner, known geological environments are rated according to instability based on actual experience. Drill hole control and geological interpretation provide the basis for forecasting unstable conditions beyond working faces. The forecasting technique has assisted mine management in reducing fall frequencies by 80% over the past two years compared to the first five years of operation. This reduction in fall frequency was accomplished by modifying the plan of advancing sections to minimize mining exposure to unstable roof conditions.

Jan 1, 1983

By W. C. Kerr

When Agassiz and his party of geologists commenced their exploration of the interior of Brazil and the Amazon region, one of the first and, to the last, one of the most novel and striking phenomena which met them everywhere was the great depth of decomposed or partially decayed rock in situ, which mantles, and for the most part conceals, the underlying strata. The same facts strike all geological observers from the North who happen to penetrate the middle and southern latitudes of the Atlantic States. In North Carolina, e. g., the entire middle and western regions, outside of the Quaternary clays, sands, and gravels of the East,—that is, all that portion of the State occupied by the Archæan and Mesozoic rocks,—show everywhere this peculiarity, so new to those accustomed to glaciated surfaces. Not only do the hills and slopes, the mountain chains and

Jan 1, 1880

By Milton E. Wadsworth, Edward M. Eyring

Better understanding of solid surfaces and their associated adsorption products is of both academic and practical value. The study of detergents and their behavior in cleaning surfaces is fundamentally related to the nature of the products adsorbed and their ability to compete for certain surfaces. Similarly in flotation, the nature of the adsorbate before and after adsorption is basic to clear understanding of the process. The recently developed pellet technique employing infrared spectroscopy provides a powerful tool for the study of solid surfaces. Absorption bands, which are infrared-active, may be observed for adsorbed products. Also any changes in the surface substrate that occur as a result of adsorption may be detected by means of differential spectra

May 1, 1956

By R. W. Braund

THE Tracy mine is within the corporate limits of Negaunee, Mich. The tract of land comprising the Tracy group lies on the east end of the Marquette Iron Range between adjoining mined-out properties on the north and south. Since acquiring the Tracy lands in 1921, Jones & Laughlin Steel Corp. has completed about 115,- 000 ft of surface diamond drilling, partially outlining five orebodies. Now that mining has started, one or more underground drills are in constant operation to obtain information that will aid mine development planning. Some 20,000 ft of underground drilling have been completed to date.

Jan 1, 1958

By Francis T. Christy

One aspect of ocean mining that is frequently overlooked in discussions is the problem of establishing some form of legal control over the seas. Much of the discussion centers on mining in territorial waters, which are controlled by the various countries according to the Geneva Convention on the Continental Shelf, and perhaps by political subdivisions of countries such as the individual states of the U.S. But as technology improves and the mining of deeper waters becomes feasible, the problem of rights outside the continental shelf and territorial waters becomes a significant factor for anyone expending the time and capital for development. Several schemes are possible for regulating ocean mining but as yet none have been instituted, except what might be termed the "wait and see" approach. Even some of the coastal states in the U.S. have no regulations governing mining in the territorial waters under their jurisdiction. Until some regulation is formulated, there may well be little development in ocean mining due to the high risk of capital involved, both with respect to companies wishing to invest their own funds and financial institutions funding a venture to develop offshore mineral deposits.

Jan 7, 1968

By Donald C. Myntti

Modern open-pit mining can be described as a capital-, labor-and energy-intensive, large-scale, mechanized, and highly repetitive bulk material preparation and handling operation, with emphasis on the word "mechanized." In hard rock, this generally means shovels loading blasted materials into haulage units for transport to processing plants, stockpiles, or waste dumps. Mine management deals with several primary concerns on a daily basis; e.g.: Will any serious accidents and labor problems occur today, and will the tonnage targets be met considering the physical condition of the equipment? The latter subject will be discussed from a maintenance perspective. A successful, progressive heavy equipment maintenance program that protects company assets involves many elements. They include: •Proper equipment selection and procurement •Well-trained and motivated workforce •Good shop facilities •Preventive maintenance (PM) program •Warehouse support •Operations-maintenance department cooperation •Meaningful paperwork

Jan 3, 1978

By G. Hergert

SUMMARY Three gradients have been identified in regard to the average horizontal ground stress increase with depth. [S (0-900 m) = 9.86 MPa + 0.0371 MPa/m SHa (900-2200 m) = 33.41 MPa + 0.0111 MPa/m SHae (extreme)= 12.36 MPa + 0.0586 MPa/m] The extreme stress values are not caused by mining geometry and are of limited extent only. In some cases geological disturbances like faults and rock type boundaries suggest an explanation but in other cases the unusually high stresses cannot be explained readily. It is interesting to note that in the same locations the vertical stress components are very much higher than those derived from overburden weight and that the vertical stress gradient is similar to the gradient obtained from the extreme horizontal stress components. INTRODUCTION Ground stress determinations have been carried out in mines in Ontario and Manitoba, Canada, over more than a decade (Herget, 1980). Most of the sites are located in the Superior and Southern Tectonic Province of the Canadian Shield, which consist of Archaen and Proterozoic rocks comprising volcanics, metamorphosed sediments and granites. The youngest orogenic deformation occurred during the Grenville Orogeny (955 million years ago).

Jan 1, 1982