Search Documents

By A. Kenneth Schellinger, O. Cutler Shepard

Overgrinding, Or the breaking of ore particles into sizes smaller than required for liberation, is a first-magnitude problem in grinding for concentration processes. The conventional ball mill-classifier circuit used in commercial grinding produces mineral particles that are all ground to pass an upper size limit, while the proportion of very fine sizes, or slimes, is uncon rolled. Calculations based on measurements made in commercial plants which were grinding ore for flotation concentration indicate that about go pct of the energy used in grinding is consumed in useless overgrinding.1 In addition to accounting for the consumption of a large amount of energy, over-grinding is detrimental to the flotation process. Overground slime coats larger partitles and inhibits selective action by the flotation reagents on particles which by themselves could be separated very well. A further difficulty is that extremely finely ground minerals do not respond satisfactorily to flotation-collecting reagents, and both selection and recovery decrease markedly with particles finer than 5 to 10 microns.2 conventional classifier-ball mill circuits inherently tend to overgrind the valuable minerals more than the gangue minerals because most valuable minerals are of higher density and are softer and more friable than the gangue minerals. The rem- edy to this situation would seem to be a separating mechanism which would separate free valuable mineral particles regardless of size and density considerations and a mechanism which would operate in the grinding mill so that valuable mineral grains would be removed from the grinding machine as soon as they are freed. A consideration of these ideas led the authors to the conception of a simultaneous grinding and flotation mechanism. So far as the authors are aware, such a machine has never been tried, even on a laboratory scale. Development oF Apparatus and Experimental Method Apparatus development went through several stages before a really workable machine was devised. Work was started with a large cast-iron mortar 7½ in. in diameter and 8 in- deep. A cast-iron disk Was mounted on the end of a vertical shaft SO that it fitted loosely into the bottom of the mortar. On top of the disk four radial cleats ¼ in. high were bolted to agitate the ball charge as the disk, or impeller, rotated. The vertical shaft was driven at 100 rpm by a mechanism improvised from an old coffee-mill type of grinder. A hole was drilled into the bottom of the mortar through which compressed air was introduced for frothing. In operation, more charges of Ore which had been crushed to pass an 8-mesh screen were placed in the bowl along with water and suitable reagents. The impeller was then started and the compressed air turned On so that the ore was ground while being exposed to air bubbles. Mineralized froth was

Jan 1, 1949

By William B. Stephenson

The paper describes efficient and effective methods of automatically controlling sand pump installations. Particular reference is made to liquid-level controls actuating variable speed pump-driving units. Included is a discussion of various combinations of equipment, with schematic drawings. HERETOFORE many sand pump installations in the mining and metallurgical field involved guesswork as to the size of the pump and then simply direct-connecting it to a constant speed motor which was often large enough to do twice the work required. Considerable thought was given to mill location in an effort to avoid as much pumping as possible. Hillside design of mills with gravity flow of tailing was much to be desired. Power costs were low, construction was relatively cheap, and labor in many places meant nothing in comparison to the values derived from the ores being treated. Today most of these conditions are reversed. Ores are becoming more complex with lower values per ton of ore treated. Power is more expensive, construction is higher, and labor definitely takes a very important place in the profit and loss statement. Each piece of equipment incorporated in the design of a new mill is selected to provide highest efficiency based on careful metallurgical analysis of the ore to be treated both in good and poor markets. Each is designed with its flexibility in mind and with provision for adjustments in its performance to meet actual conditions in the operation of the mill. Sand pumps have taken an important position in mill design. Operators the world over are relying more and more on the performance of a sand pump in the efficient operating of their plant. Many ordinary jobs are being done today with pumps driven through adjustable pitch diameter V belt drives in order that changes in pump speed can be made easily to meet actual operating conditions. Operating costs have long since proved the folly of operating a pump at too high a speed for the volume and head to be overcome. Metallurgical results have shown the benefits derived from a smooth flow as contrasted with a surging flow from an uncontrolled pump. Construction costs have risen to such an extent that surge bins and other means formerly employed must be omitted from today's flowsheet. Several installations of considerable size and involving the use of automatic pump speed control have proved the adaptability of such controls since they were placed in service in recent years. In the following presentation each system discussed and illustrated schematically has been installed in one or more instances and has proved itself reliable and definitely economical from the standpoint of capital investment, operation and maintenance. Variable Volume-Head Speed Control: Probably the most popular, effective and efficient automatic control setup for sand pumping installations is the one shown schematically in fig. 1. Commonly used

Jan 1, 1951

The Cuajone and Toquepala copper projects are located in the extreme southern area of Peru. Since 1960, Southern Peru Copper Company has operated the Toquepala open -pit mine, flotation mill, 110 smelter, townsites, power plants, and railroad. Toquepala and 10, the smelter and port location, are connected by a 110-mile-long (176 lun) railroad. Much of Toquepala's infrastructure has been used for the Cuajone project. Cuajone, at an elevation of 11,400 ft (3475 m), required five standard-guage railroad tunnels with a combined length of 17 miles (27.2 km) to connect with Toquepala so concentrates could be shipped to the no smelter. The total cost of Cuajone is estimated at $726 million for a designed annual capacity of 180,000 tons of copper, equivalent to about $4,000 per ton of installed production capacity. This relatively low cost per ton, by today's standards, has been made possible through the use of the 110-to Toquepala railroad, the ability to expand the 110 copper smelter, and other favorable factors. To mine the 468 million tons of copper sulfide or e at a grade of 1.0% copper, approximately 24 1 million tons of waste were stripped- before mining of ore to supply the new Botiflaca 45, 000 ton per day concentrator. The mining rate must exceed 300,000 tons of waste plus ore per day to maintain the 45, 0 00 tpd sulfide ore milling rate which was to be reached at the end of 1976. Waste stripping is done with 15 cu yd electric shovels and 120 -ton trucks. Ore mining is done with 8 and 9 yd shovels. A railroad connects the pit with the 60 in. by 89 in. Allis-Chalmers gyratory crusher. Side-dump railroad cars of 50.cu yd capacity dump onto a 0 16 ft 9 in. long (5. 1 m) grizzly inclined at 40º with 7 to 8 in. (178 to 203 rnrn) bar spacings. The grizzly is divided into two 22 ft 4 in. (6.8 m) wide sections and two side -dump railroad cars discharge simultaneously into the 150-ton capacity dump pocket. A Barco rock manipulator is used for breaking or removing oversize from the dump pocket. The bin receiving the grizzly undersize has a capacity of 5,000 tons, and the pocket beneath the crusher holds 900 tons. Each is equipped with an 84 in. apron feeder, which feeds a 60 in. (1.52 m) conveyor belt to the 150,000 ton coarse ore stockpile, where the ore is distributed by a 72 in. (1. 83 m) tripper conveyor. The 45, 000 live tons in the coarse ore stockpile are reclaimed by twelve 48 in. (1. 22 m) apron feeders. Maintenance on the crusher eccentric is made easy by an eccentric

Jan 1, 1978

By John C. Robison

INTRODUCTION Sensitivity analysis is a means of gauging the impact of individual risks on a financing. Key risks can occur in three time periods: - Feasibility, engineering and construction phase; - Start up phase (usually through completion); - Operating phase (post completion). If a company has agreed to cover these risks prior to completion, then less attention will be paid to the sensitivity of the project in the first two time periods. Since the operating phase of the project generates cash for both operations and debt service and generally does not begin until two to six years after the loan is signed, it is wise to look at scenarios other than the projected "base-case" scenario in order to determine the project's capability to operate successfully under a broad range of probable future events. Lenders are compensated at a fixed spread over their borrowing base and generally are not compensated if the project is successful beyond expectation. They are also subject to the loss of principal plus funding costs if the project performs below expectation. Because of this, lenders establish sensitivities around the parameters of conservative projections developed in the project feasibility studies and the cash flows resulting from these projections. The initial cash flow projections should demonstrate the project's ability to meet cash costs, debt service requirements (principal and interest), and still have sufficient cushion to cover contingencies such as strikes, price fluctuations, force majeur situations, etc. (See Schreiber, Chapter 10). The selection of the level of sensitivity analysis to be performed is the result of both objective criteria, including probabilistic analysis applied to the technical parameters, and, of equal importance, subjective criteria applied by the analysts, especially with regard to the economic and financial parameters impacting the project cash flows. RISK SENSITIVITY Assumptions used in the cash flow projections should be realistic. Risks identified by the lenders should be identified and cash flows prepared to assess whether these project risks are acceptable. Typical project risks include the following (see also Chapter 9): - Sufficient reserves - quantity and quality - Product price - Production level - Operating costs - Availability of energy and supplies - Transportation and infrastructure requirements and costs - Interest rate - Completion risks - Tax level - Political risks - Cost over-run risks - Operator experience - Management - Technological risks - Environmental permits and risks - Foreign exchange risks - Insurance coverage - Equity of sponsors - Inflation rate - Capital expenditure during project life In order to see the effect on the cash flow projections, each risk should be analyzed for its impact on the cash flow generating capacity of the project. Sensitivities can be examined to see if the resultant cash flow projection will meet the lenders minimum credit standards. 1.Reserve Sensitivity In general, lenders will not assume the reserve risk. However, it should also be noted that lenders receive loan proposals in which reserves range anywhere from proven to possible. Sensitivities are not generally run for various reserve levels and reserve estimates are either considered acceptable or not acceptable by the lenders.

Jan 1, 1985

By J. H. Slater

There is nothing particularly new about the use of sinter in a blast-furnace burden. For many years flue dust has been sintered at the various blast-furnace plants to put it in a form that could be recharged to the furnace with some assurance that it would stay in the second time. This paper is not a compilation of scientific data but only an attempt to give our experience with sinter. There are some unexplained discrepancies in the tests given here, such as the flue dust produced and iron tonnages, but the results given are the results that were obtained. Sinter is not the cure-all for blast-furnace problems. A good coke is still the most important factor in good furnace operation. However, good sinter is a big help. As flue dust is produced under varying operating conditions and fluctuates greatly in carbon content, it is difficult to produce from flue dust alone a uniform sinter, which will give satisfactory blast-furnace results. Sinter made from flue dust alone will change in character with every carbon variation. Almost invariably flue dust contains carbon in excess of the amount necessary to make good sinter, and this excess must be burned out. This, of course, necessitates reduction of the speed of the sintering machine and thus a decrease in tonnage. An alternative is to dilute with a carbon-free material to use up the excess carbon. High-carbon material when sintered results in a very dense, undesirable product, since the excess heat melts the charge into a hard, nonporous mass, and tends to form refractory silicates. At the Republic Steel plant in Cleveland, there had existed since 1924 a continuous-type sintering machine having 224 sq. in. of grate-bar area, capable of producing 9 to 11 tons of sinter per hour from flue dust. Under a former management, it was the practice to sinter only the flue dust from the blast furnaces, no attempt being made to recover the gas-washer sludge. As the dust was limited, the plant operated only part time. In other words, there was a sintering plant representing considerable investment, with good facilities for screening and preparation of raw materials, and flue dust available for only part-time operation. The sinter produced was costly and not a very desirable product. The first step was to install equipment for the recovery of the gas-washer sludge. This was done in the form of two large thickeners and a filter, which have proved very satisfactory. It was then decided to screen out the minus 3/8-in. fines from the Mesabi ores, mix them with flue dust and coke breeze when necessary, and operate the plant at full capacity. The tonnage increased to 18 tons per hour and the product was much improved. Sintering costs fell and the product was a preferred blast-furnace material, which on an iron unit cost compared very favorably with good Mesabi ores. On the average, 40 per cent flue dust and 60 per cent fine ore was being used. The oversize from the ore screening also became a preferred product for the

Jan 1, 1941

The great Bingham Canyon mine and mill complex of Magna, Arthur, and Bonneville had their beginning in a 300 ton per day operation which was commenced by Daniel C. Jackling and his associates in 1904 as the Utah Copper Company. This small plant was quickly expanded to 500 tons per day and eventually Kennecott, the Utah Copper successor, was processing about 45,000 tons per day of ore in each of its mills, Magna and Arthur. Finally, in 1966, the Bonneville crushing and grinding plant was added to produce a slurry of ground ore for flotation concentration at the expanded Magna and Arthur mills. Bonneville is one of the few railroad dump primary gyratory crushing plants constructed in recent years; another which is described in this Monograph is Cuajone in Peru, started in 1976. Two others are the Climax Henderson unit and the Phelps Dodge Tyrone crusher, which has been fed by trucks since it commenced operation. The Bonneville, Henderson, and Cuajone crushers are all located considerable distances from their mines, hence the use of rail haulage. Shovels in the Bingham pit are 8 to 15 yd capacity; and ore is sent to the Bonneville crusher in 100 ton rail cars, where they are dumped, two at a time, by a hydraulically driven rotary dumper. Ahead of the 54 in. by 74 in. Allis-Chalmers gyratory are two grizzlies, each 27 ft 9 in. (8.46 m) long with bar spacings of 4 ½ in. (114 mm) at the feed end and 6 in. (152 mm) at the discharge end. Grizzlies are sloped at 38. Oversize rocks are re- moved from the crusher pocket by an overhead crane, and the crusher produces a nominal 6 in. (152 mm) product. Rail cars are dumped in the direction away from the crusher, and water sprays at the dumper level and in the rock boxes are used for dust suppression. There are two 72 in. by 19 ft (1.83 m by 5. 8 m) apron feeders under the 500 st cr'ushed ore pocket and two more under the grizzly undersize pocket. Feeder speeds are variable up to 72 fpm. Grizzly undersize is dropped to the feeder pocket by three shelves forming a rock ladder attached to the pocket walls. Each pair of apron feeders, one for crushed ore and one for grizzly undersize, discharge to a 72 in. (1. 83 m) picking belt for tramp removal; this belt feeds one of two 54 in. (1.37 m) feeder conveyors which in turn discharge to a 60 in. (1. 52 m) takeaway belt operating at 175-300 fpm (53.3 - 97.4 mpm). Both picking belts are equipped with metal detectors and tramp iron magnets, and a separate 30 in. (760 mm) conveyor is used to remove tramp material.

Jan 1, 1978

By G. H. Clevenger

The reagents now used in flotation consist of various acids or salts, which may be either electrolytes or non-electrolytes, dissolved in water and some substance or combination of substances which function as collecting or frothing agents. At times the only dissolved salts present are those naturally occurring in the water used. The general effect of the electrolyte is to greatly sharpen the separation between the gangue and the concentrate. Examples of this are: The use of sulphuric acid with zinc ores; and of sodium carbonate or calcium oxide (lime) with silver-gold ores. Crude pyroligneous acid is also sometimes used when avail able. Various oxidizing agents, such as permanganates, bichromates, etc., are added in the selective flotation of lead-zinc ores. Many other reagents for performing certain specific functions, either real or imaginary, have been proposed, and a number of them have been tried upon a working scale. The wild orgy of experimentation which is now going on in flotation exceeds even that which followed the introduction of the Washoe process for the treatment of Comstock ores, when, among other things, sage-brush tea and tobacco juice were reagents added to the pans. Out of all this will, of course, eventually come a more or less standard practice for the treatment of each class of ore. Omitting a discussion of the functions of frothing and collecting agents, the reagents used in flotation for this purpose may be classified under five general heads: (1) Essential oils; (2) fixed or fatty oils; (3) alcohols and their combinations with organic acids; (4) coal tar and its refined products; (5) petroleum and its refined products. A flotative agent of some kind is required in flotation as now practiced. A single reagent, as, for example, certain of the essential oils, may perform the dual function of frothing and collecting agent, or a mixture of substances may be required. In this country, the essential oils used have been wood products, and have been almost exclusively confined to the steam-distilled pine oils. At the present time, the supply of these is limited, and the cost almost prohibitive, so that their use has been dispensed with as far as possible. The oils and tars resulting from the destructive distillation of

Jan 1, 1917

By R. S. Shoemaker, F. W. McQuiston

The principle of cyanide recovery or regeneration of cyanide from solution, be it a weak wash or a foul solution, is by acidulation. All or part of the cyanogen is converted thereby into hydrogen cyanide which is fixed by an alkali (generally lime) and returned to the cyaniding system (the Mills- Crowe process). The solution is made acid by bringing it into contact with sulfur dioxide. The acidified solution is stripped in a packed tower by a counter flow stream of air in which the air and the solution are brought into intimate contact. The air leaving the tank charged with hydrogen cyanide is then passed to another tank in which it is mixed with an alkaline solution, the latter absorbing the HCN and leaving the accompanying air clean for reuse in removing more HCN from the acidified solutions. Of the recoverable cyanide, 9770 is usually recovered in a three-unit disperser tower system. When there is a considerable content of copper, the solution is made acid following standard procedure; however, the HCN is not removed until the copper is reduced by regeneration. Copper removal at this point may be as high as 90%. After reduction of the copper, the acidified solution then is contacted with a lime solution which brings down calcium sulfate as a second step. The silver, gold, and copper are recovered in the form of a precipitate which can be shipped to a smelter. At the Hudson Bay Mining and Smelting Company, Ltd., most of the precious metals have been recovered in the copper and lead concentrates, but it has been found profitable to submit the flotation tailings to a scavenger cyanide treatment for the recovery of exposed gold contained in pyrite rejected during flotation. Due to the fine particle size, maximum dissolution is achieved in a four-hour contact period. In the cyanidation plant, the thickened flotation tailing at 70% solids is given a four-hour agitation in weak calcium cyanide solution and filtered. Filter cake is repulped and discharged either to the tailing storage area or to the mine as backfill. Clarification, de-aeration and precipitation of pregnant solutions are carried out in a standard Merrill-Crowe unit. Typical analysis of precipitate is as follows: Au, 0.47%, Ag, 4. 88%; Cu, 46.0%; Zn, 13. 8%. Cyanicides in the form of copper minerals limit the reuse of barren solution. To recover the substantial quantities of cyanogen chemically combined with base metals in this solution, a cyanide regeneration plant is in operation. The barren solution is acidified with sulfuric acid in a spray tower where an upward current of air from a blower sweeps the liberated hydrocyanic acid gas to an adsorption unit where it meets a fine rain of lime suspended in plant solution with which it combines to form calcium cyanide. The lime--water solution carrying calcium cyanide is reused in the cyanide circuit. The return gases are drawn into the blower and back to the disperser tower thus

Jan 1, 1975

By Benjamin L. Miller

THE essential differences expressed by the different speakers participating in this symposium concern merely the relative emphasis placed on the subjects that are commonly included under the term "geophysics" and the branches of science that form the basis for investigations in this field. In order to appreciate the present situation it may be profitable to briefly refer to a few historical matters. One can find almost countless descriptions of geological phenomena long antedating the introduction of the title of "geology," which has been credited to Richard de Bury in the fourteenth century. Interpretations, when they were offered, were generally pure speculation. Only toward the close of the eighteenth century do we find theories developed as the result of observations and tested by additional observations. It is difficult to select and give proper credit to the individual who was particularly responsible for turning geology into a distinctly observational science. William Smith, who has been called the "Father of English Geology," certainly represents the period when observation was the only method used. As he traveled through the British Isles, "sometimes 10,000 miles in a year," he was continually making notes of his observations. Geikie says: "His plain, solid, matter of fact intellect never branched into theory or speculation, but occupied itself wholly in the observation of facts." William Smith, with others of his time, definitely laid firmly the foundations on which modern geology has been built. Field and laboratory observations can no longer be said to constitute the sole basis for geologic contributions but we have not laid aside the methods of Smith and his followers. It is folly to underestimate the fundamental value of the observational part of geology in the present. The objection to purely observational geology is that it is mainly qualitative and not quantitative, general and not specific. No one can deny this charge and probably there are few who do not welcome every method or process whereby we can put aside generalities for definite established values. Physics is the science that has particularly come to the aid of the geologist in this respect. CONTRIBUTIONS OF PHYSICS It is not the intent of the writer to enumerate or to evaluate all of the contributions to geologic advance in the field of physics. A few only are used for the purpose of illustration. When Clarence King, Director of the United States Geological Exploration of the Fortieth Parallel, invited Ferdinand Zirkel to study 2500 thin sections of rocks collected from the western United States, the use of the microscope came into general use. Zirkel's report was published in 1876. He was not the first to use transmitted light for microscopic rock determination, some work having been done by Henry Clifton Sorby and others some years earlier, but he was the first to put into general use this method. We may well claim that this

Jan 1, 1941

By H. C. Ray

ABOUT the beginning of 1930, coal preparation had reached the stage where the cleaning of coal by liquid or air had become the order of the day. Since that time many new preparation plants have been installed in spite of the years of depression in the coal industry, and this is indicative of a trend wherein the coal producer found it expedient to manufacture a cleaner product in order to compete with other fuels. It was also about 1930 that, because of the difficulties encountered with fine coal in cleaning plants, dust collectors came into use. Both cleaning plants and dust collectors, therefore, were much discussed at the engineering meetings of the early 1930's. During these meetings the many advantages to be gained through the use of dust-collecting systems were pointed out by Hebley,1 Appleyard2 and others. The great possibilities of new markets for this product were emphasized and discussed at the same time; however, the disposal of the collected dust remained a problem. Since the purpose of dust collecting is to improve the preparation and, consequently, the salability of the coal, it seems illogical to return the collected dust to any of the coal being prepared for market use, as is done in preparation plants that include dust-collecting systems. The logical thing is to dispose of the dust in some useful and practical manner outside of the tipple. As a practical matter, this can be done in one or both of two ways; either by consuming the dust at the mine's own power plant or by marketing the dust direct to the consumer. The latter method not only offers the greatest opportunities, but is the most important, because of inequalities that may exist between the quantity of dust collected and the consuming capacity of the mine's power plant. In considering the more important marketing possibilities, we are confronted immediately with the problems connected with the handling and transportation of so fine a material. It is this problem, rather than the problem of finding new markets, that has been responsible for the lack of progress in the matter of dust disposal. It is the purpose of this paper to point out again some of the potential market outlets, and also to describe an existing system of handling and transporting coal dust. To the best of the writer's knowledge, this is the first and only operation in this country that has handled fine-mesh coal in bulk 50-ton lots direct to the consumer. POtential Markets for Fine-mesh Coal Dust In general, the potential market outlets would include any operation of which the pulverization of coal is a necessary part. To be more specific, a few of the better known operations of this type must include: colloidal-fuel plants, briquetting plants, "sea coal" distributing plants, water-purification plants and, obviously, pow-

Jan 1, 1944

US 4,137,751-Aerial geophysical exploration for ore deposits by collecting and analyzing atmospheric particulates The aircraft has an Inlet duct extending outward and including a "shave-off" duct, a cyclone separator located inside the cabin which is coupled to the inlet duct, a clean air exhaust duct, and a receiver for the collected particles incoming air is divided into two fractions. The fraction taken by the "shave-off" duct and containing the bulk of the particles is routed to the cyclone Particulates are gathered on a collector tape for subsequent analysis and correlation with the areas covered J. R Rhodes, R D. Sieberg, M. C Taylor, J. C Westkaemper, and R C. Young, assigned to Columbia Scientific Industries, Inc Feb. 6, 1979 7 pp. (73-28) Filed- 2-28-75 (554,114) Same British 1,446,760, dated Aug. 18, 1976. US 4,156,138-Exploration for subsurface deposits of uranium ore Pairs of dosimeters are placed underground in a grid pattern Each dosimeter contains a phosphor which IS capable of storing the energy of alpha particles. One dosimeter is heavily shielded from alpha particles, while the other in the pair is thinly shielded to exclude dust After a period underground the dosimeters are heated to release the stored energy as light. The amount of light produced from the heavily shielded dosimeter is subtracted from the amount of light produced from the thinly shielded dosimeter to give an indication of the location and quantity of uranium underground This patent is a division of US Patent No 4,053,772, dated Oct 11, 1977 P E Felice, assigned to Westinghouse Electric Corp May 22, 1979 5 pp (250-253) Filed. 8-12-77 (824,203) US 4,180,727-Method for measuring the gamma-gamma density of uranium ore in the vicinity of a borehole A first gamma-ray detector receives only natural gamma rays from the borehole, while a second receives both natural gamma rays and scattered uranium-source gamma rays The value of the uranium-source gamma rays is calculated. W W Givens, assigned to Mob11 011 Corp Dec 25, 1979 6 pp (250- 264) Filed 10-20-77 (843,909) US 4,180,72&A neutron activation probe for determining the location and grade of uranium ore, especially where thorium or other fissionable isotopes are present, includes a pulsed neutron source in series with a plurality of delayed neutron reactors for measuring radioactivity in a well bore- hole together with a Nal(T1) counter for measuring the high energy 2 62 MeV gamma line from thorium The signal from the Nal(T1) counter IS subtracted from the signal from the delayed source detectors to ascertain the amount of uranium present in the ore body N. P Goldstein and R C Smith, assigned to Westinghouse Electric Corp Dec 25,1979 6 pp (250-264) Filed. 4-1 1-78 (895,323)

Jan 1, 1980

By Louis Moyd

In the preparation of illustrations to accompany reports of investigations concerning particle shapes of various natural and manufactured materials proposed for use as he aggretates in concrete structures, it was found that stereoscopic views of such materials presented the information much more effectively than the usual two-dimensional photographs. With the whole-hearted cooperation of the Photographic Section, a technique was developed in the petro-graphic laboratory of the Concrete Research Division, U.S. Corps of Engineers, at Clinton, Miss., for simple and rapid preparation of paired stereoscopic photographs and micrographs. The method requires only equipment which is usually part of the general stock of any laboratory, and it is adaptable for all purposes in which three-dimensional views would be found superior to ordinary photographs. Stereoscopic Photographs Where the subject or subjects to be photographed are small but not of microscopic size, an ordinary camera having a ground-glass focusing screen is set up vertically over the field. The material to be photographed is placed on a card, the surface of which is suitable as a background. The card is mounted so that it can be tilted about 5' above and below the horizontal plane, on an axis that coincides with the north-south diameter of the viewing screen. A simple way of achieving this is to mount the card on an object having a convex lower surface. In our laboratory, a watch-glass has been used, with plasticene as the mounting medium. The convex surface should be mounted on a support having a round opening on top and a flat bottom. A roll of tape, a petri dish, a beaker, or any other piece of equipment having the proper shape to give stability to the setup will be satisfactory. The arrangement of the required equipment is shown in Fig 1. For the best results, the subject to be photographed should be mounted in the plane of the axis of rotation. To achieve this effect, the depth of the mass of plasticene between the background and the watch-glass is varied so that when the watch-glass is tilted back and forth on the axis, the subject to be photographed does not appear to move back and forth across the viewing screen. A permanent piece of equipment, embodying an adjustable vertical screw, with lock-nuts, could be made for this purpose. The subject may be illuminated in any manner desired. It was found that the presence of shadows intensifies the effect of depth. In taking the photographs, the concave surface is mounted so that one side of the background card is about 5' below the horizontal, while the axis remains in the horizontal plane. The subject is focused carefully on the ground glass and a picture is taken. The card is then tilted so that the opposite side is about 5' below the horizontal, while the axis still remains in the horizontal plane. The subject is again put in focus and another picture is taken. After both pictures are developed and printed, they are placed side by side in the same orientation and examined with a stereoscopic viewer. If depressions appear where there ought

Jan 1, 1950

By James Norman

BARITE (BaSO4) is the most important industrial barium mineral from the standpoint of quantity consumed. In 1938 the amount was 365,000 tons. Its uses are numerous, some of the more important being in the production of pigments, as an inert filler in a wide variety of products, as a weighting material in oil-well drilling muds, in the manufacture of some kinds of glass, and in the production of barium chemicals. The barite studied in this investigation occurs as the massive variety in a shale replacement formation near Magnet Cove, Ark. It is intimately mixed with quartz and small amounts of iron oxide and residual shale. Complete liberation of barite and quartz is not obtained when the rock is ground to loo per cent through 325 mesh. The crude rock with which all test work was done assayed 85.1 per cent BaSO4, 11.11 per cent SiO2, and 2.85 per cent R2O3. Its specific gravity was 4.03. It was found in the course of the investigation that the barite contained a small amount of uniformly distributed carbonaceous material, so intimately dispersed that it could not be seen with the microscope, but gave a definite gray cast to the barite concentrates. The color of the barite in polished sections of the crude rock ranged from gray to almost black, while finely ground powder was a reddish gray. The reddish hue was due to the iron oxide present. In 1939, under the supervision of Oliver C. Ralston,* the Bureau of Mines, in cooperation with the Milwhite Company, of Houston, Texas, undertook to study the flotation of barite from Magnet Cove, Ark. Flotation of several southern barite ores had already been investigated by the Bureau of Mines.' The Magnet Cove barite was unique, however, in that it had to be ground to such an extremely small particle size for liberation. The flotation of nonmetallic minerals in the presence of a large amount of slime is usually very difficult and when done is an innovation calling for conditions different from those under which granular material is separated. LABORATORY FLOTATION WORK Preliminary investigation showed that the flotation reagents recommended by O'Meara and Coe1 for separating barite and siliceous material were suitable, but much larger quantities of reagents were required to separate such finely divided material. Moreover, it was found that careful control of the frothing was necessary. When oleic acid and sodium silicate were used a voluminous froth was observed at the beginning of a test, and toward the end there was not enough froth to effect complete recovery of barite. The addition of pine oil as a frother gave proper frothing for the duration of the test, and the substitution of coconut fatty acid (crude lauric acid) for oleic acid produced a more heavily burdened froth. Two different paper-mill fatty-acid products were tested

Jan 1, 1941

By C. A. Siebert, D. J. Girardi

PRACTICALLY every metallurgical process in-volves, at some stage or another, the contact of a metal with a gas. Because of this, gas-metal re-actions are of great practical importance and have been subjected to numerous investigations. It has long been recognized that the presence of cuprous oxide in liquid copper has an important effect on its casting characteristics and .physical properties. This has led to the desirability of determining the quantitative relationships between cuprous oxide in the liquid copper and the usual gases present during processing. Such data are not only of practical importance but also of a theoretical interest in that they provide a means of applying the principles of physical chemistry to problems in applied metallurgy. The object of this investigation was to determine the quantitative relationship at equilibrium between the gases carbon monoxide and carbon dioxide and the cuprous oxide content of liquid copper. The reaction and its equilibrium constant may be expressed as follows: 2 Cu (liq) + CO2 (g) = Cu2O + CO (g) acu2o X aco/a2 cu X aco2 Here the underlined symbol Cu2O designates cuprous oxide dissolved in liquid copper and (a), the activity of the various constituents. The activities of carbon monoxide and carbon dioxide are assumed to be directly proportional to their re- spective partial pressures and the activities of cuprous oxide and copper are taken to be proportional to their respective mol fractions. The equilibrium constant may then be expressed as follows: K2 = Ncu2o X Pco [Ncu]2 X Pco2 where N = mol fraction The solubility of carbon monoxide and carbon dioxide in liquid copper is a rather controversial subject.'-' A review of the literature is given by 0. W. Ellis.' It appears that carbon monoxide and carbon dioxide are both only very slightly, if at all, soluble in liquid copper. Volskii and Slobodskoi5 determined the equilibrium between carbon monoxide, carbon dioxide, and liquid copper at 1100°C. Their results show a higher cuprous oxide content for a given CO/CO2 ratio than found in the present work. The system hydrogen, water vapor, and liquid copper was investigated by Allen and Hewitt8 over the temperature range of 1090" to 1350°C. Equilibrium values for the system carbon monoxide, carbon dioxide, and liquid copper calculated from these data agree reasonably well with the present work. Materials and Procedure The copper used was oxygen free, designated as OF and analyzed as 99.98 pct copper with no appreciable amount of any one impurity based upon spectrographic determinations. The carbon dioxide was cylinder gas averaging about 99.95 pct CO2 with air as the major impurity. The carbon monoxide was produced by passing carbon dioxide over heated charcoal. Alundum combustion boats were used as containers for the liquid copper. No appreciable reaction took place between the copper and the alumina. This was evident from the fact that the copper sample after a run did not ordinarily adhere to the bottom of the boat and that the

Jan 1, 1951

By P More

US 4,132,621-In the electrowinning of aluminum, the cells are aligned in a lengthwise direction so as to lessen the harmful influence of the induced magnetic fields Each cell is supplied with current from the preceding cell both via the head arid at least one side riser The output of the cathode bars is divided into two separate groups, the upstream group supplying the head of the subsequent cell arid the downstream group supplying the side risers of the subsequent cell This produces a substantial improvement in cell efficiency arid a greater regularity P Morel, J P Dugois, arid B Langon, assigned to Aluminium Pechiney. Jan 2, 1979 12 pp. (204¬243M) Filed 1-12-78 (868,861) Priority: France, 1-19-77 (77/2,213) US 4,134,806-Cells, anodes, arid methods for use in the electrowinning of nickel, cobalt, copper, zinc, or other metals from an acid ore leach solution or the like The cell is provided with vertically immersed stationary cathodes and stationary rod anodes which are noncorrodible by the electrolyte arid are electrocatalytic to the anode reaction. The spaced parallel anode rods are connected to electric current supply bars The anode rods have an electroconductive core made of a metal alloy arid a surface coating of an oxide of platinum or a platinum group metal The ratio of active cathode surface area to active anode surface area is preferably at least 3 0. De Nora arid C Traini, assigned to Diamond Shamrock Tech¬nologies, SA Jan 16, 1979 13 pp. (204-105R) Filed 9-15-77 (833,661) Priority Italy, 1-29-73 (19738 A/73). Same British 1,434,334-5, dated May 5, 1976 US 4,135,994-In the electrowinning of aluminum at a high current efficiency, the electrolytic bath is a mixed molten salt consisting of 2-15% by weight of aluminum trichloride, 15-83% of sodium chloride, 15-70% of combined calcium chloride arid magnesium chloride but riot more than 40% of calcium chloride, arid optionally up to 10% of barium chloride Preferably, plate-shaped graphite electrodes used for both cathodes and anodes are arranged in parallel inclined relation so that the axis in the lengthwise direction makes an angle of from 10° to 45° to the horizontal. T Ishikawa arid H Ichikawa, assigned to Nippon Light Metal Co Ltd Jan 23, 1979 4 pp (204-67) Filed 11-15-77(851,632) Same British 1,550,502, dated Aug 15, 1979

Jan 1, 1980

By C. M. Marquardt

Tramp iron and steel moving on a conveyor belt cause small currents to be generated in a coil situated in a strong magnetic field, which are converted to an alternating current and are amplified. The output voltage from the amplifier fires a thyratron with a relay in its anode circuit, which actuates a howler and simultaneously drops a spot of marker material on the belt. THE problem of tramp iron removal from moving ore belts is a long standing one. When heavy ore streams are carried on a belt, magnetic pulleys and strong surface magnets fail to remove tramp buried in the ore stream. Tramp iron buried in the ore stream cannot be pulled from the bed by surface magnets and is carried past the magnetic pulley by the falling ore stream. With the increased use of detachable bits the problem of the detection and removal of tramp has become more necessary and difficult. Several types of tramp detectors have been developed. It would serve no practical purpose here to review exhaustively the literature on the subject. Methods of tramp detection used are: (1) The magnetic method, wherein the small current generated by the magnetized tramp passing a Coil is used. (2) The unbalanced oscillator method wherein the tank circuit of a stable radio- or audio-frequency oscillator is unbalanced causing a change of frequency or a change in plate current due to changes in eddy currents, hysteresis, or dielectric because of the presence of tramp. (3) The bridge methods wherein the impedance of one leg of an alternating current inductive bridge is changed due to the presence of conducting tramp. Each of these methods of tramp detection has its field of usefulness. The second and third methods are excellent for oxide iron ores, coal, sand and gravel, grain, etc. However, these latter methods are not suitable for use on ores that contain rich conducting sulphides, since a large piece of pyrite or galena will cause the same detector response as a piece of tramp iron. At the Caselton, Nevada, plant of the Combined Metals Reduction Co., sulphide ores are treated; therefore, it was necessary that a tramp detector operating on only the magnetic properties of the tramp iron be used. Tramp iron detectors of this type operate on the principle that if a piece of tramp iron moves near a coil in a high intensity, steady magnetic field, the presence of the moving tramp iron causes the magnetic flux lines through the coil to change. This induces a mall current in the Coil. In series with the Coil is generally placed a relay sensitive to currents of 1 to 3 microamp. When the tramp iron passes near the coil the flux linkages change, causing this very sensitive relay to actuate. Since the contacts of such a relay are very small it must actuate a second relay capable of breaking a larger current

Jan 1, 1951

By N. Mungan

Laboratory water floods were performed in oil-wet and waterwet alundum and Torpedo cores, displacing a refined oil with n-hexylamine or Triton X-100 solution. Also, some floods were performed in which a sucrose solution was displaced with n-butyl alcohol. The Purpose ot the tests was to see if the oil recotlery could be increased and to examine what role the inter-facial tension reduction and wettability change play in the recovery mechanism. it was found that the chromatographic transport of amine was influenced by core wettability. In oil-wet cores, the rate of advance of the amine band could be predicted from equilibrium chromato-graphy, while in water-wet cores the amine band moved faster than predicted, indicating a non-equilibrium process. By reducing the interfacial tension to 1.1 dyne/ cm, oil recovery was increased. More oil was recovered from Dri-filmed cores than from water-wet cores. Reversing the wettability of the porous media from oil-wet condition also resulted in some additional oil recovery. Neutral wettability floods did not increase oil recovery. INTRODUCTION Interfacial forces in petroleum reservoirs are responsible for retention of large quantities of residual oil. Increasing exploration costs have created an incentive to attempt recovery of this residual oil by new and novel processes. One novel process involves changing the interfacial forces by introducing a chemical into the reservoir during water flooding. Recently, several investigators have carried out laboratory displacement tests using amines. lt3.4 The amines adsorbed onto initially water-wet core surfaces, changing them to oil wet. Additional oil was recovered when the cores were flooded in a manner reversing the. wettability from oil-wet conditions. In all these studies, the wettability reversal was considered responsible for increased oil recoveries although it was noted that amines also reduced oil-water interfacial tension. In the present study, displacement experiments were performed in water-wet and Dri-filmed cores. The purpose was to separate the effects of lowering the interfacial tension from changing the wettability. LABORATORY STUDY All experimental data given in this paper have been obtained at a temperature of 70F + 1 and prevailing atmospheric pressure. FLUIDS AND MATERIALS The oil used in these experiments* was washed with H2S04 and passed through two 100-200 mesh silica-gel beds to remove unsaturates and surface active impurities. Normal hexylamine** of practical purity was used, and the alundum cores*** were composed of nearly pure A1203. Fused quartz (SiOi) and Lucalox (A12 )t plates were used in the contact angle measurements. DISPLACEMENT TESTS Displacement tests were performed in alundum and Torpedo cores. Before displacement runs, cores were acidized with 0.1 normal HCI, flushed with distilled water and fired at 1,200F to make them water wet. This procedure also reduced water sensitivity of the Torpedo cores. Oil-wet cores were prepared from water-wet cores by flowing several pore volumes of 1 per cent by weight Dri-film SC-87 solution in heptane through the cores, flushing the cores with nitrogen, evacuating, and finally heating the cores at 300F for 4 or 5 hours. Between floods, cores were cleaned by conventional procedures and treated again as above.

Jan 1, 1965

By Clarence W. Dunham

BECAUSE of the earthquakes that occur at Chuquicamata, the design of the smelter stacks constituted the most difficult structural problem of the entire sulphide ore project. Slight tremors occur almost daily and shocks of moderate magnitude are not uncommon. Naturally, the operation of the smelter depends upon the safety of these stacks, and their resistance to earthquakes was the critical feature of their design. Adequate data of the magnitudes of past shocks at Chuquicamata were not available. However, considering the information that was obtained from experiences in other parts of Chile, a period of one to two seconds was adopted as a basis for the design. To complicate the problem further, the stacks had to provide for operations under a wide variety of conditions ranging from the possibility of running one reverberatory furnace and two converters initially to perhaps five or six furnaces and eight or ten converters simultaneously in the completed plant. No one could tell for certain just what the ultimate capacity might have to be because the plans permitted a large extension beyond the first installation if this became necessary. Studies of the stacks were made for many conditions. At first it was thought that one stack 600 or 650 ft high should be used initially for both the furnaces and converters, with a second similar stack to be built for the future extension. This height would provide adequate draft in the rarified atmosphere at the plant's elevation of 10,000 ft. It would also disperse the gases high in the air. Preliminary studies of this large stack showed that such a structure was possible if made of steel but it would be exceedingly costly. Furthermore, the effects of the tendency for the top to whip under the action of earthquakes might be serious, and the design had to be based upon assumptions which might not be trustworthy. Such a tall stack was finally abandoned in favor of a larger number of smaller ones. Initially, one stack will service the first three or four furnaces. Another will handle the gases from four or five converters. The smelter has been located in such a position that the prevailing winds carry the fumes away from the remainder of the plant. A height of 300 ft for the stacks was finally selected. The top diameter is approximately 24 ft 9 in. clear inside of the lining. The converter stack is located upon a hill alongside the smelter. This provides an effective increase in height because its base is approximately 66 ft above the yard level. The base of the reverberatory stack is at the latter elevation. Stacks made of reinforced concrete or of steel were investigated, and so were many shapes for them. As these studies progressed, the lightness of a steel structure, and the ductility of the metal itself, led to the decision to use steel for the main part of the stacks. The fact that serious damage to one of the stacks would cause the plant to shut down, caused special studies to be made of the stress conditions that might exist around the breeching which had to be nearly 15 ft wide and 40 ft or more high where it joined the stack. This height was necessary in order to provide adequate transition from the horizontal flow of the gases to the vertical direction without undue eddies. This opening constituted a serious source of weakness in the structure. If made with sufficiently strong reinforcement around its edges, there would be a hard spot in the structure that might cause trouble because of shaft vibrations.

Jan 1, 1952

By F. W. Smith

Within the Northern Pennine Orefield, England, intersections of fluorite veins are generally richest in ore, and their recognition enables investigation of the ore potential of the intersecting bodies. A method, based on routine analysis of fluorite for yttrium, has been used with success in mines of the district to predict the location of intersections in partially developed fluorite-bearing ore bodies. This short note is intended as a brief introduction; the details of United Kingdom applications are to be published at a later date. Geology The Northern Pennine Orefield is the second largest fluorspar-producing region in Britain. The associated minerals galena, sphalerite, chalcopyrite, barite, and witherite have all been extensively worked in the past but, with the exception of a single barytes mine, all of these operations are now abandoned. Galena alone is recovered as a byproduct of fluorspar beneficiation. At the present time two companies are producing about 38,000 tpy of fluorspar from high grade vein ore bodies, and a number of concerns are actively prospecting in old lead workings. The mineralization is localized in veins and replacement flats within favorable lithologies in an alternating limestone, sandstone, shale sequence. Since the thickness of individual beds is not great (generally less than 20 m), vein bodies tend to be ribbon-shaped, with length greatly exceeding width and height (Dunham). They thus present difficult exploration targets for conventional diamond drilling techniques. Ore grade varies greatly along the veins, which can change rapidly in character from mineral stained fault gouge to massive mineral bodies up to 10 m in width. It has been known for a very long time that the richer ore bodies tend to be associated with vein intersections in favorable beds. It is assumed that vein fissure intersections provided vertical channelways through which hot ore-bearing brines were able to ascend from deeper cavities in the sequence. Thus investigation of intersections at other horizons generally yields further ore bodies. Technique The relative concentration of yttrium in fluorite is a good indicator, in the North Pennines, of the direction of flow of mineralizing fluids. In all of the ore bodies so far studied in detail in this region, the concentration of yttrium increases markedly in the direction of vein intersections that are believed to have acted as feeder zones to the remainder of the bodies. The reason for this relationship is probably connected with the degradation of soluble rare earths-fluoride complexes by the changes in various physicochemical parameters of the hydrothermal fluids as they entered the ore body cavities from the feeder zones. The simultaneous release of free fluoride ions also contributed to the increased ore values in these intersection zones. Yttrium values in fluorite taken from a longitudinal traverse of the western ore body, Redburn mine, Rookhope, are plotted in [Fig. 1.] The position of a major vein branch and three cross veins are clearly indicated by yttrium maxima. The cross veins themselves contain up to 2.5 m of low grade fluorspar ore. The exact positions of B and C were unknown previous to the geochemical survey. Similar results have been obtained for several other veins and ore bodies in the area. Clean fluorspar was collected as bulk samples from within 300 mm of the vein wall and, since the vein infilling is simple, with mineral growth from the walls inward, analyses of the samples are considered comparable along the length of the ore body. A number of samples taken from the center of the vein show a

Jan 1, 1975

By A. T. Aldred, K. M. Myles

The vapor pressure of chromium over solid V-Cr alloys has been measured by the torsion-effusion method in the temperature range 1450" to 1650°K. The chemical activities as well as the free energies, entropies, and enthalpies of formation of the alloys have hem computed from the vapor-pressure data. The activities of both chromium and vanadium exhibit fairly small negative deviations from Raoult's law over the entire composition range. The values of the excess entropies and the enthalpies of formation found at 1550°K are considered in terms of the changes in the clzaracteristic properties of vanadium and chromium that occur upon alloying. RECENT interest in the theory and properties of transition-metal alloys has shown the need for relevant thermodynamic data. The present investigation of the V-Cr system was undertaken as part of a more general study of thermodynamic properties of transition-metal alloys. The system was chosen because of the reported complete solid solubility of the components at all temperatures1 and because the difference in magnitude of the vapor pressures of vanadium and chromium allowed a simple effusion technique to be used. The torsion-effusion method was employed to minimize compositional changes in the alloys during the experiments. EXPERIMENTAL Equipment. The torsion-effusion apparatus, shown diagrammatic ally in Fig. 1, consists of a torsion system suspended inside a vertical vacuum chamber whose lower end is surrounded by a high-temperature vacuum furnace. An auxiliary optical lever and screen are used to determine the angle of rotation of the effusion cell. The torsion fiber is an annealed, high-purity, tungsten wire usually between 0.003 and 0.007 cm in diameter and about 43 cm long. The wire supports a concave mirror and a rigid tantalum connector tube. The effusion cell is fastened to the lower end of the connector tube by a dovetailed yoke and har- ness arrangement. The cells, which are 1.27 cm in diameter and 4.4 cm long, were made by electron-beam welding tantalum endcaps onto a 0.025-cm-wall tantalum tube. The two orifices, formed by drilling, have similar areas ranging from 0.011 to 0.031 sq cm. The noninductive sheath-type furnace consists of a single-phase tantalum heating element 6.35 cm in diameter, 15 cm high, and 0.013 cm thick; the element is completely surrounded by radiation shields in an evacuated chamber. The power system includes a 17-kva self-saturating saturable core reactor with an integral magnetic amplifier and a water-cooled, 15-kva, step-down power transformer with a multitap secondary. Temperatures are controlled to within ±1/2o at 1600°K by means of a unit that includes a reference voltage source, a dc electronic null detector, a current-adjusting proportional band relay, and the self - saturating reactor. At 1650°K the temperature variation within the cell, vertically and horizontally, is 3/4oK. Unwanted motions of the torsion system are damped by the movement of an aluminum vane, which is mounted on the connector tube, between the poles of an electromagnet. When not in use the magnet is withdrawn and rotated 90 deg to prevent its interaction with the rotation of the system. Measurements. The vapor pressure, p, is re-

Jan 1, 1964