Search Documents

ZAY JEFFRIES, Cleveland, Ohio (written discussion?).-The authors conclude that there is a certain average size of precipitated CuAl2 par-ticle which produces maximum strength and hardness in duralumin; that when the size of particle is smaller or larger than this particular size the hardness decreases. The writer agrees with this conclusion, because it seems to he directly indicated by the facts. Why does duralumin present this apparent discrepancy? Let us con-sider some physical aspects of the precipitation of CuAl2 from a saturated solution on cooling. When a molecule of CuAI3 is removed from the solvent, or matrix, and added to another group of CuAl2 molecules, as is known to occur on slow cooling, the forces of adhesion between the CuAl2 molecule and the solvent have been exceeded. Since a. change in tem-perature only is sufficient to cause precipitation, it must also be sufficient to cause the loss of adhesion bonds between the excess CuAl2 molecules and the solvent, or matrix. Lost adhesion bonds means loss of cohesion of the mass as a whole. When duralumin is cooled from 500° in a furnace, globules of CuAl2, large enough to be seen easily with a high-power microscope, are formed. There are, however, globules so small as to be hardly distinguishable, and others too small to be resolved are suggested by the non-uniformity of the surface appearance of the section. As the smallest globule of CuAl2 resolvable with a high-power microscope contains about 2,000,-000,000 molecules, it is evident that with rapid cooling submicroscopic particles of CuAl2 must be present in large numbers; in fact, after quench-

Jan 12, 1919

By D. S. Cahn, D. W. Fuerstenau

Specimens of glass, plexiglass, and naturally occurring minerals were irradiated by a 15-joule ruby laser pulse to determine criteria for the fracture of nonmetallic solids by internal thermal stresses. Fracture did not occur in those specimens with either a very high or very low internal absorptance or with a high spectral reflectance. If significant amounts of melting and vaporization do not occur at the surface of irradiation, the specimen will fracture if a derived 11fracture stress" exceeds the ultimate tensile strength of the specimen. The purpose of this investigation was to determine criteria for the fracture of nonmetallic solids by internal thermal stresses which are caused by absorption of laser irradiation. A laser produces a very short pulse of light which has a high energy density distributed over a very narrow part of the visible spectrum. The laser system used in this investigation had an energy output of 15 0 joules at a wavelength of 6940 A. Fracture in a non-metallic solid, then, would be caused by the absorption of light energy by that solid, and subsequent conversion of this energy to heat or mechanical energy. Fracture is caused by internal stresses that result from rapidly imposed nonequilibrium thermal gradients. ANALYSIS OF CONDITIONS FOR FRACTURE BY LASER IRRADIATION For this analysis, the laser beam is assumed to be circular and centered on the junction of the major and minor axes of a rectangular specimen. The laser beam forms a cylinder of radius rb extending through the specimen width. The beam cylinder may be then thought of as a heated mass constrained by a surrounding unheated mass. The instantaneously heated cylinder will at-

Jan 1, 1968

By Kandalla Ravindranath, C. C. Patel

Studies of the adsorption of dialkyldithiocarbamates at the surfaces of galena and sphalerite have shown that characteristic contact angles are obtained at galena surfaces in the 7-10 pH range, whereas lower angles are obtained at unactivated sphalerite surfaces even at pH 71 Further, the angles at sphalerite surfaces progressively decrease with increase in pH. However, when sphalerite is activated with cupric sulfate, characteristic contact angles are obtained at pH 7 and beyond. This shows that galena and sphalerite can be selectively floated with dithiocarbamate collectors at pH 7 and beyond. Experimental Materials Ore: The lead-zinc ore for the present study was obtained through the courtesy of the Geological Survey of India from Dariba, Udaipur, Rajasthan, India. The average ore analyzed 15.5% lead, 11.6% zinc, 6.7% iron, 15.6% sulfur and 36.6% acid insolubles. The ore was crushed in a Denver laboratory rod mill and sieved in a Denver automatic sieve shaker to obtain a -200- to +250-mesh (Tyler standard) fraction. This particular size was chosen because it was conducive to good liberation of sulfide minerals, both from one another and from gangue minerals. Collectors: Dimethyl, diethyl, diisopropyl and diisobutyl dithiocarbamates were prepared and purified by the methods described by Klopping and Van der Kerk.2 A freshly prepared 0.03% dithiocarbamate solution in distilled water was used for flotation studies. Frother: A 0.03% solution of pine oil in ethyl alcohol was employed. Activator: 7.3 g of cupric sulfate pentahydrate were dissolved in 1 1 of water and used for the activation of sphalerite. Depressant: 16.0 g of zinc sulfate heptahydrate were dissolved in 1 1 of water and used for the depression of sphalerite.

Jan 1, 1972

By E. C. Roberts

TO facilitate some recent microscopic investigations it was necessary to devise special mounting techniques for the polishing of two quite different metallographic specimens. These techniques are extremely simple and are submitted for whatever value they may be to other investigators. The first specimen mount proved very satisfactory for the study of untempered martensite. Since it was undesirable to heat the specimen, lucite or bakelite mounting materials could not be used in the conventional manner. A cold mount was made by drilling a hole of the same diameter as the specimen in a cylindrical piece of polystyrene then press- ing the steel specimen into the hole on an ordinary vise. A prefabricated disk of lucite should work equally well. The only precautions necessary are that the hole be drilled out cleanly and the piece of steel be pressed into the plastic uniformly, otherwise the mount will crack. The second type of mount was required for the study of slag specimens by reflected light. Mounting these specimens in bakelite and then attempting to rough finish the surfaces on graded emery papers resulted in a considerable amount of chipping and breaking out of the slag particles. This made further satisfactory polishing almost impossible. It was found, however, that if the bakelite-mounted specimen was first rough finished to a point where a good specimen surface became visible, the interstices in the specimen surface could be filled and the polishing completed. This filling was accomplished by placing a small amount of lucite powder in the bottom of the steel specimen mold then reinserting the bakelite-mounted specimen on top of the lucite powder. Reheating the mold to the proper temperature and applying the required pressure resulted in the formation of a thin disk of lucite on the bottom of the bakelite specimen. By carefully grinding the lucite away a uniform surface including the slag specimen was obtained and further polishing was unhampered by slag disintegration.

Jan 1, 1951

By Rossiter W. Raymond

The most important event in the history of mining in the United States was the discovery of gold in California, which led to the rapid development, not only of a new industry, but of a new empire. The settlement of the Pacific slope was making but slow progress under the inducements of a scanty commerce in furs and hides. The liberal grants offered by the government to agricultural pioneers in Oregon had attracted to the Willamette valley and other favored points in that territory a limited population; hot the government of the Mexicans in California was positively unfavorable to enterprise. It is true that gold was known to exist in the country. Rumors of it were current among the trappers, and placers had actually been worked in what is now Los Angeles County; but the padres of the neighboring mission of San Fernando had discouraged the business as demoralizing to their flocks; and the existence of the precious metal was not widely known; still less was its distribution northward suspected. The discovery of gold, January 19th) 1848, at Sutter's saw-mill, on the south fork of the American River, afterward famous as Coloma, in Eldorado County, was the beginning of the new epoch. This discovery was made by James Wilson Marshall, a partner in the mill, who observed in the debris washed down by the tail-race a glittering fragment of a mineral unknown to him. Suspecting it to be gold, he sought for further specimens, and obtained, in the course of a few days, several ounces of it. Tests subsequently

By C. M. Young

BITUMINOUS coal piled in heaps or bins frequently undergoes a process of spontaneous heating as the result of the absorption of oxygen. It seems probable that the first absorption of oxygen by coal which has not previously been exposed to the air may occur as a condensation or a combination of oxygen in some form which does not result in the production of carbon dioxide, but slow combustion soon begins. The absorption of oxygen is accompanied by an increase of temperature, and this by in increased rapidity of absorption; hence the dangerous condition proceeds from bad to worse, until the kindling point is reached, unless the process is interrupted. A dangerous rise of temperature can be prevented by excluding oxygen, by increasing the bulk of coal in proportion to its surface exposed, or by circulating enough air to dissipate the heat produced. The storage of coal, in practice, varies from almost complete exclusion of oxygen, by storing under water, to such freedom of access as exists when the coal is stored in open piles. Oxygen available for absorption by coal is supplied by the air in the interstices between lumps and by additional air which may enter the pile through circulation. The size, of the coal largely affects both of these supplies; for if the fragments a re small the spaces between them constitute a small percentage of the total volume, and little oxygen will be available unless the circulation of air brings in a fresh supply, while with large fragments the percentage is relatively large; circulation also is much easier through a pile of coarse lumps. In the case f lump coal, although a large amount of air may be present, the exposed surface is comparatively small and there is little opportunity for the absorption of oxygen to so rapid as to cause dangerous heating. Attempts have been made to prevent heating by allowing a sufficient circulation of air to carry off the heat generated; obviously this method cannot be applied to fine sizes nor mixed sizes.

Jan 2, 1918

By F. E. Minshall

FoR more than 30 years California has been one of the three leading oil-producing states. Present daily production of crude oil under curtailment, approximately 580,000 bbl., comes from three general areas: Los Angeles Basin, San Joaquin Valley, and the coastal region of Ventura and Santa Barbara Counties. This state produces approximately two-thirds of its oil from eight large fields, and obtains a daily average production of 48 bbl. of oil per producing well, whereas the average for the United States is but 8.15 barrels. During the closing stages of the first half of 1936, discovery of the Section Ten oil field was made, and credit goes solely to geophysical work. It is the first direct important discovery of oil in California that may be credited to geophysics. This discovery may furnish the cue to the means of discovering several fields in California, particularly in the San Joaquin Valley. It is a question, however, whether returns from geophysical work will play as important a part in the future supply of oil in California as have our former types of prospecting. Explobation Methods of prospecting have progressed in the oil industry through invention or improvement in scientific means of locating and defining structure and because of market improvements in drilling equipment. Present methods of prospecting include: 1. A detailed study of geology in an attempt to locate structural and stratigraphic conditions that would be favorable to the accumulation of oil. 2. Geophysical methods involving the use of the seismograph, torsion balance, magnetometer and electrical methods. (There is still much to be learned in California in the application of geophysical methods.) 3. Use of micropaleontology as an aid in correlation,. The principal improvements in drilling equipment are: 1. The Schlumberger dipmeter, which determines the direction of formation dip in an uncased hole.

Jan 1, 1937

By Earl A. Trager

The broad picture of world petroleum production at the present time is one of an excessive supply. In any consideration of corrective measures to be applied in the future, it will be necessary to include all the producing areas of the entire world. To illustrate, United States production during 1931 was 48 million barrels1 less than 1930, whereas world production exclusive of the United States increased, owing principally to increases in Russia, Rumania and Persia. Domestic Peoduction Let us first consider the domestic production situation. Due to the fact that United States production was maintained below current demand, about 40 million barrels of oil were withdrawn from storage during 1931. Consumption increased about 1.5 per cent over 1930, which is less than the recent annual rate of increase of 8 to 11 per cent. If the machinery to prevent waste in the petroleum industry operative for more than a year will continue during the coming year and drilling is held to the 1931 level, there will be a decided improvement in the domestic situation by the close of 1932. This will be due in large measure to the drastic reduction in exploratory work and drilling which has been in effect for more than a year. Looking ahead for two or more years, probably there will be a shortage of domestic production in relation to domestic demand, unless there are discovered several large pools comparable to Oklahoma City or East Texas. Were the United States isolated, our problems in so far as petroleum production is concerned might be considered well along the road to recovery. To maintain this perspective will require the cooperation of foreign producers in the future, or protection of United Statcs markets from foreign invasion. Let us review briefly the present situation in the United States. East Texas has been the most important factor during 1931. The large initial production of individual wells and the rapid rate of drilling

Jan 1, 1932

By Robert L. Bates

An industrial mineral, says the Glossary of Geologic Terms, is "any rock, mineral, or other naturally occurring substance of economic value, exclusive of metallic ores, mineral fuels, and gemstones; one of the nonmetallics." Probably most geologists and engineers would accept this simple and straightforward definition, at least as a general statement. On analysis, however, certain anomalies crop up. For example, it may be considered arbitrary to include industrial diamond and corundum, but to exclude their precious varieties, gem diamond and sapphire. So the present volume has a section on gems and gem materials, in spite of the definition. Another problem arises when we try to define precisely what is metallic and what is nonmetallic. Bauxite and ilmenite certainly qualify as metallic ores, but both are also raw materials of important nonmetallic substances; hence they are included in the book. A third anomaly is that, by common consent of geologists, engineers, mineral economists, and others concerned, the term industrial minerals may include not only rocks and minerals but also certain manufactured products like cement and lime, and even mixed groups of natural and artificial products, such as abrasives and refractories. Thus the central realm of the industrial minerals is clear enough, but its boundaries tend to be indefinable. Since a definition that allowed for every irregularity in the outer fringes would be excessively un- wieldy, the one quoted above may be considered satisfactory. The expression industrial minerals is commonly equated with nonmetallics, and with the somewhat more precise phrase industrial minerals and rocks as in the title of this book.

Jan 1, 1975

By David J. Raden

INTRODUCTION Economic deposits of phosphate are found at shallow depths (80 ft.) in central and northern Florida (Figure 1) where they have been mined since the late19th century(l).The present (1978) mining rate is approximately 40 million short tons per year of product (called “phosphate rock1”), which represents approximately 80% of the total U.S. production and 30% of the world production. The principal use of Florida phosphate is for the manufacture of fertilizer. There are 10 major mining companies and 20 active mines in Florida at the present time, strip mining approximately 5000 acres per year. The ore, known as "matrix," consists of gravelly clayey sands containing phosphate minerals (principally carbonate fluorapatite), quartz, and clay minerals. The clay to phosphate ratio is generally about 1:1 by weight and the sand to phosphate ratio ranges from, 1:1 to about 3:1. Mining is done by large electric draglines, which strip and cast the sandy overburden soils, generally 10 to 40 feet deep, and remove the matrix, generally 10 to 25 feet deep. Dragline bucket capacities are generally 20 to 45 cubic yards, but range up to 65 cubic yards. Mining cuts are usually 300 to 500 feet wide and up to several thousand feet long. The ore is cast into an earthen sump where high pressure water guns are used to slurrify it. Centrifugal pumps move the slurry through a pipeline to a beneficiation plant where the phosphate rock is separated from the waste sand and clays.

Jan 1, 1979

By A. E. Wells

In this paper are described various comparative tests made on cracked and straight run gasolines. The results of these tests may be briefly summarized as follows: Samples of 54 to 55° Bé. gravity cracked gasolines, with end point of about 442° F., and with a somewhat larger proportion of the less volatile fractions than conformable to government specifications, were used in a single cylinder variable compression engine under the same conditions as were samples of straight run gasoline of 58 to 59° Bé. gravity, and of which one had a greater proportion of the more volatile fractions than called for in government specifications. The cracked gasolines showed decidedly less tendency to knock, hence could be used at higher compression ratios and thereby developed from 10 to 20 per cent. more power than did the straight run gasolines. These figures may be taken as one measure of the superiority of the cracked gasolines under test with the straight run gasolines. It is not claimed that all cracked gasolines are superior to all straight run gasolines to the extent indicated by the above tests; cracked gasolines vary as do the straight run products. Cross's work and that of others have indicated that certain cracked products may have a much greater superiority over straight run than that determined above. From various sources and by different methods of testing data are being obtained to show the definite and generally quite considerable superiority, as an anti-Cetonating fuel of cracked gasolines over straight run gasolines. It is now becoming generally recognized that by increasing the production of cracked gasoline motor fuel from those heavier petroleum fractions, which otherwise would be used for burning purposes, the petroleum industry is not only working in the interest of the conservation of the world's supply of petroleum, but is at the same time making available to the gasoline-consuming public a product distinctly superior to the straight run gasolines.

Jan 1, 1927

By Arthur C. Spencer

In extension of a suggestion already made to account for certain features observed in the Juneau gold-belt in southeastern Alaska,' it is the object of the present paper to indicate in detail certain conditions in which deformation of rocks under their own weight might lead to the production of fractures in which veins could be deposited. A direct, uniformly-distributed pressure of sufficient intensity, applied to an elastic brittle mass offering strung resistance to deformation, produces rupture. In a material of ideal properties the surfaces of rupture under such pressure would be shearing planes inclined at 45' to the line of force, unless there be preliminary deformation, in which case this angle would be greater than 45. This general conclusion, resting upon analytical mechanics, is completely supported by the results obtained by DaubrBe2 in experiments upon the deformation of wax and resin prisms under compression. Let us then first consider one of Daubree's diagrams. In the case illustrated in Fig. 1, four sets of fractures in two approximately right-angled pairs (that is to say, in conjugate sets) were produced by endwise compression of a square cross-sectioned prism. These fractures cut the axis of compression at approximately equal angles, not varying greatly from 45o. The location of the four sets of fractures is obviously determined by the shape of the prism, since the material in each corner acts in a way as a buttress, permitting the bulging to take place most readily on the sides. By limiting the directions in which bulging may take place, results of a more simple nature could be obtained. Take, for instance, a square prism, and place it between two fixed and

Jan 1, 1906

By J. W. Pugh, Sam Leber

Single crystals of tungsten were made and deformed in tension at 3000°C. The slip traces so formed on these crystals were analysed to determine the apparent slip system. Results indicate that deformation occurs in the<III> direction on planes of maximum shear stress. This determination agrees with the early work of Taylor and Elam on other body-centered cubic crystals at lout temperatures. SLIP in face-centered cubic and hexagonal close-packed metals has consistently manifested itself in straight traces which indicate that glide takes place on planes of highest atomic density and in directions of closest packing. The slip traces observed on body-centered cubic metals are, on the other hand, frequently branched and wavy, and indicate that while glide takes place in the direction of closest packing, it does not necessarily choose the plane of highest density. The early work of Taylor and Elam1 4 indicated that glide took place in the close-packed direction on planes close to those defined by the maximum shear stress. Subsequent investigations have tried to rationalize these observations in terms of an elementary process on the close-packed planes (110). For example, Elam5 and Grenin~er&apos; have suggested alternate glide on nonparallel (110) planes with the observed result that the summation of these glides results in a trace which defines some plane other than{110). Madden and chen7 have recently reviewed the phenomenological and theoretical aspects of noncrystallographic slip. More recently Koehler&apos; has presented a model of dislocation propagation which permits another rationalization. He indicated that dislocation loops are transferred from one glide plane to another by double cross-slip of screw segments. It is reasonable to assume that, on the average, such transfers may result in a trace which approaches the plane of maximum shear stress. The work described in this paper will show that

Jan 1, 1961

By R. S. Shoemaker, F. W. McQuiston

MAGMA COPPER COMPANY San Manuel Division The San Manuel Division of Magma Copper Company is located about 40 miles north of Tucson. Tons of ore milled in 1973 .were approximately 19 million at a rate of 63,000 tons per day. From this, about 42,600 tons of copper concentrate was produced as saying approximately 1.070 MoS2 and 28.5% Cu. As with many copper ores, the San Manuel ore contains a small amount of gold, but in this particular case, much of the gold follows the molybdenite. Separation of the molybdenite from the bulk sulfide concentrate by flotation produces a moly concentrate containing 9170 MoS2, just under 1.070 Cu, and 0.44 oz Au per ton. Cyanidation of this material for gold recovery is the only practice of its kind known to the authors of this Monograph. After thickening, the final moly concentrate is filtered for subsequent repulping with cyanide and lime. Gold dissolution takes place in three agitators in series with the pulp from the agitators being filtered in two stages in disc filters. Between filtration stages, the cake is repulped with barren solution. Filtrate from both filters is the pregnant solution. The Merrill-Crowe recovery unit is comprised of two solution tanks and the usual clarifying filter, vacuum tower, zinc dust feeder and Merrill precipitate press. Because of the presence of finely divided sooty chalcocite in the molybdenum concentrate, the cyanide consumption of 55 pounds per ton is extremely high. A compensating factor, however, is the low copper, moly concentrate produced. Precipitation of the gold from the highly copper-contaminated solution requires 0.56 pounds of zinc dust and 0.28 pounds of lead acetate per ton, high figures when compared to normal cyanidation practice. The Merrill- Crowe precipitate assays approximately 28.5% Cu, 8% Zn, 156 oz Au and 197 oz Ag per ton. The San Manuel cyanidation plant is an outstanding and innovative development.

Jan 1, 1975

By Ralph Nichols

THE mines are near the town of Gilmore, in the Texas mining district. This district was organized in 1880. The present producing mines are near the terminus of the Gilmore & Pittsburg railroad. This railroad connects with the main line of the Oregon Short Line at Armstead, Mont. The distance from Gilmore to Armstead is 70 miles. The town of Gilmore is near the head of the Lemhi river at an elevation of 7,000 ft., while the mines are from 400 to 1,300 ft. higher. The range of mountains upon which the mines are situated forms the water shed for the Little Lost river on the west and the, Lemhi river on the east. The winters are severe and the snow fall is heavy, but the mines ship right through the year. There is an abundance of timber suitable for all mining purposes in the immediate vicinity. Water is piped into the camp from a lake about 2.5 miles distant. This lake is about 1,400 ft. above the town of Gilmore. The water is exceptionally good for boiler and domestic purposes. The mining companies now producing are. the Pittsburg Idaho Co., Ltd. ; the Latest Out Mining & Smelting Co:, Ltd. ; and the Gilmore Mining Co., Ltd. Besides the above properties, there are a number .of prospects in different stages of development. The producing mines of the district are fissures in limestone, with a general northeast-southwest course .and a dip to the west of from 40° to 70°. These fissures are at about right angles to the bedding of the limestones. The veins are regular and the ore shoots strong, both laterally and in depth, so far as developed. The ore shoots have a rake or pitch to the south. The character of the formation is shown in Fig. 1, a section of the Latest Out mine.

Jan 11, 1913

By Chester Washburne

AT present it is impossible to estimate closely the amount of oil obtainable from a given area of land. However, after the completion of a few properly distributed prospect wells, one can calculate the approximate yield of the sands penetrated, with a probable error of say 50 per cent. Even rough predictions of this kind are of value in, large operations. Without wells upon it, one can never be absolutely certain that an area will produce any oil whatever, and one can only indulge in wild guesses of the probable productive area, before the geological structure has been carefully contoured and the top of the basal water plotted on a map. This requires wells. At times it is desirable to form an idea of the possible yield of oil in advance of drilling, as in cases where the price asked for undeveloped land seems too high, but where the probability of finding oil is furnished by neighboring development, supported by the geology. In such cases the most one can do is to make an estimate of possible maximum yield, which may of course far exceed results, and which is of use mainly in the prevention of excessive initial investment. The method is very significant in a general way, as in regions like the Bighorn Basin, Wyoming, where the productive sands in the Cretaceous shale are so few and so thin and fine that they cannot develop very great production, although the high quality of the oil probably will counterbalance this defect sufficiently to give local profit in favorable areas. Reservoir Capacity of Sands.-The porosity of a stratum is the measure of its maximum reservoir capacity for liquids and gases. The porosity may be determined experimentally and must be used in connection with the total volume of the sand.

Jan 2, 1915

1. Any society of undergraduates at a technical school, comprising students in any branch of engineering, metallurgy, chemistry, geology, etc., may be recognized by the Board of Directors in its discretion as an Affiliated Student Society, and its name, together with the names of its president and its secretary, may be published in Mining and Metallurgy or the Directory of the Institute. The members of such a society will not be named individually on the membership list of the Institute, but may at any time be proposed for election as Student Associates or Junior Members of the Institute, in the usual way. 2. Membership in an Affiliated Student Society, certified by the official representative thereof, and accompanied by suitable testimony as to character and qualifications, will have special weight with the Membership Committee of the Institute, in its consideration of the proposal of a candidate for membership. The Affiliated Student Societies receive the following privileges: 1. A copy of Mining and Metallurgy free; 2. The use of Employment Service; 3. The use of Mining and Metallurgy for publicity purposes, such as printing notices of their activities, etc.; 4. Assistance in obtaining speakers for their meetings, lists of moving-picture films, etc. To retain the privileges of the Affiliated Student Society, its officers must keep in touch with the Secretary of the Institute and advise him of its activities. The foregoing plan is not confined to students in mining engineering or metallurgy. Any undergraduate society of engineers may avail itself of the privileges offered. Societies desiring to be recognized as Affiliated Student Societies are requested to make application to the Secretary of the Institute, giving particulars as to the nature, membership and officers. The following list gives the names of the Affiliated Student Societies as of December 1, 1929, and their presidents and secretaries.

Jan 1, 1929

By Irwin Remson

Some unique hydrogeologic issues are inherent in the problems of siting, designing and licensing a mined geologic high-level nuclear waste repository. The problems involve hydrogeologically unfamiliar rocks for which little proven technology has been developed, long containment periods, elevated temperatures, and externally-imposed management constraints. In evaluating the existing national program, it should be recognized that hydrogeology is only one aspect of the total nuclear waste disposal problem, that the use of multiple barriers requires that the hydrogeologic system be considered in its entirety as a total system, and that engineering modifications can improve the isolation capabilities of certain barriers. Important research questions involve the mechanics of transport through dense fractured and unfractured rocks, methods for measuring vertical hydraulic conductivity, and a variety of geochemical questions. Current expectations for "high quality data" from either in situ or laboratory testing are unrealistic, and a modified approach to repository hydrogeology is needed. The dilemma is that the hydrogeological characteristics that make a potential host rock more satisfactory for respository siting are the same characteristics that are difficult to characterize and make the particular site more difficult to license. Finally, evaluation of the containment potential of any candidate site will become meaningful only with detailed underground exploration, mapping and testing in the host rock formations at the repository levels.

Jan 1, 1984

By James Norman

SPODUMENE is a lithium-bearing pyroxene, and is an important source of lithium compounds. Because of its high alumina and lithia content, it might be a desirable constituent of glass batches. The use of spodu-mene in ceramics will undoubtedly increase, as it has been shown that a mixture of the proper proportions of this mineral with soda feldspar and potash feldspar has a much lower maturing temperature upon firing than has any one of the three components.1 The mineral spodumene seldom occurs as pure mineral, but ordinarily with feldspars, mica and quartz. All spodumene-bearing rocks tested contained these minerals as gangue. Small amounts of iron and manga-nese oxides also were present, usually as stains on the silicate grains. Mica associated with the spodumene carried a considerable amount of lithia. This was discovered in flotation tailings, which, although virtually free of spodumene grains when examined microscopically, showed 0.4 to 0.5 per cent Li2O on chemical analysis. The lithia content of micas picked from the North Carolina spodumene rock was variable. Some samples contained little lithia, others more than 3 per cent. In 1938, under the supervision of Oliver C. Ralston, ? the Bureau of Mines, in cooperation with the Tennessee Mineral Products Corporation, undertook to study the beneficiation of North Carolina spodumene by froth flotation. The Bureau had previously published investigations on the beneficiation of spodumene.2,3 The methods described in the second publication&apos; did not give good results with badly weathered spodumene rock, so that more thorough investigation of the subject was warranted.

Jan 1, 1940

By John L. Baum

GEOLOGISTS and engineers working around a diamond drill rig have often had the opportunity to observe the magnetic attraction of drill rods pulled out of the hole for core removal. This is sometimes an amusing pastime, but this same magnetic force inadvertently applied to a compass needle can cause it to lose its polarity entirely or to become reverse polarized when placed in the immediate vicinity of stacked rods. The first recommendation, of course, would be to avoid the rods, but in surveying an operating drillhole this is not always possible; therefore steps must be taken to neutralize the magnetic effect of the drill rods. Early in the summer of 1949 the geological department of the New Jersey Zinc Co. undertook at Franklin, N. J., an extensive program of surveying the course of deep diamond drillholes. The majority of the holes were surveyed while in the process of being drilled, and considerable difficulty was encountered. A pattern for the deviation of drillholes had been established for the district from surveys in holes from which the drill rig had been removed. It was observed that a certain operating deep drill- hole being surveyed did not fit this pattern. In the resulting confusion of repeated surveys and cementing a plug for wedging operations, the lower 1800 ft of the hole was lost. Because of this incident studies were initiated to determine the source of the difficulties and to develop safeguards against recurrence of faulty surveys.

Jan 12, 1954