Search Documents

By F. C. Newton

REFINERS of lead by the Parkes process have always been solicitous of recovering the zinc used in the desilverization, and justly so, as the loss in zinc constitutes one of the heavy costs in this method of refining. Part of this loss is due to the absorption of zinc by lead, and in the present state of knowledge is not recoverable as metallic zinc. The remainder of the zinc, which finds its way into the precious-metal-bearing crust, is recoverable and naturally engages the operators' most exacting attention. Careful elimination of the impurities in base bullion has enabled the refiner to produce a zinc crust better adapted to retorting, which reflects favorably in the zinc recovery; and to produce a richer crust, thereby lowering the zincking cost, as the increased efficiency of the zinc results in less of it being in circulation. It is obvious that if the ratio of concentration be increased, a lessening of the amount of crust formed will ensue, throwing less work on the retorts and diminishing the amount of retort metal sent to the cupels, thus making an actual money saving in all these operations. In the effort to obtain a rich crust, the metallurgist has increased the heat to a considerable degree, upon the assumption that at the higher temperature the zinc-silver alloy could be squeezed free from the adhering lead. A further possibility for improvement suggested itself in the freezing-point curve of Prof. H. C. Carpenter, upon zinc and silver. Study of this curve disclosed the existence of a definite chemical compound, . Zn3Ag2, with a freezing point of 665° C., a promising compound for practical application.

Jan 2, 1915

By E. F. Bailey, L. S. Birks

The effect of stress on the austenite to ferrite transformation in carbon steel was studied by X-ray diffraction techniques. Tensile stress was found to cause reorienta-tion of austenite above the transformation temperature, to accelerate equilibrium conditions at the transformation temperature, and to cause precipitation of large carbides at a critical value of stress. IN the past, a number of papers' have discussed the effect of stress on the austenite to martensite transformation at relatively low temperatures. In general, it has been shown that tensile stress induces some transformation at a given temperature, while compressive stress retards the transformation. Very little work has been reported on the effect of stress on the transformation from austenite to ferrite plus carbide near the A, point in steel. One of the few papers in the literature2 reports an increase in A1 of about 1°C in pearlitic steel upon the application of tensile stress. In this paper, the effect of tensile stress on eutec-toid steel at, and above, the A, point was studied in

Jan 1, 1956

By Thomas M. Turner

Open pit mining, always a demanding task, faces two relatively new problems today: (1) availability of equipment and (2) environmental restrictions. The modern dredge offers relief in both problem areas. Delivery on a major dredge might run 18 to 24 months rather than 60 months; and lowering of the water table is precluded, thus minimizing environmental objections. In addition, a lower first cost and potentially increased efficiency may offer real advantages to the miner who is forced away from his traditional mining methods. What are the objections to the use of a dredge in open pit mining? Perhaps first and foremost is the natural reluctance to change from a successful operation. Who can blame the miner who has developed expertise in the use of the dragline if he is reluctant to change to a new mining technique that requires new and different skills? A part of the same problem is the miners' desire to control the excavation visually in order to delineate sharply between overburden and matrix. This problem can be alleviated significantly by utilizing good boring data and a positive acquisition cutter. In the final analysis, however, if the miner is prohibited from dewatering the area, either he mines the deposit by dredge or not at all. There is little doubt that when the decision is made to remove overburden and/or matrix by dredge, the problems of delineating between overburden and matrix, creation of slimes, and development of mining plans to minimize double handling etc., will be addressed and solved. There are two broad categories of dredges: mechanical and hydraulic.

Jan 1, 1976

By H. l. Burghoff

DURING the course of preparation of crystals of alpha brass for an investigation of their creep characteristics, a number of critically oriented crystals were produced. In each of these specimens, P0, the specimen axis, lay near some important crystallographic direction or on or near the border of two possible slip systems. Because of the unusual nature of their orientations, it was considered of interest to deform these speci-mens in simple tension and to study orientation changes and any unusual occurrences, different from what would be expected for specimens in which only one slip system had distinctly the highest maximum resolved shear stress. Choice of actual operating slip system in a crystal offering an immedi-ate possibility of two slip systems would be expected to be due to chance, defect, or some inhomogeneity. Even in an ideally perfect crystal so oriented, the natural oscillations of the atoms about their lattice positions would give rise to a condition wherein one slip system would be favored over the other at the critical shear stress. In the large, nonperfect crystals of the present investigation, slip on both systems, but in different portions of the specimen, might occasionally be expected.

Jan 1, 1940

By F. P. Agterberg

It can be useful to model the mean grade values for a metal in mineral deposits containing that metal as representing the extreme value tail of a lognormal frequency distribution for the concentration values of the metal in common rocks of all types. Results for copper and zinc in the Abitibi area of the Canadian Shield are compared to results previously obtained for the Canadian Appalachian region. The lognormal model is also applied to a set of 162 large gold deposits in the Abitibi area. In the second part of the paper, 1311 large and small gold deposits in the Abitibi area are modeled as discrete events. By means of a newly developed spatial clustering model it is possible to predict the variances of random variables for frequencies of deposits in cells of different sizes.

Jan 1, 1981

By L. L. Hirsch, W. M. Parris, P. D. Frost

IT has been established that titanium alloys con- taining sufficient amounts of ß-stabilizing elements, such as iron, chromium, or manganese, can be age hardened.' Adenstedt, Pequignot, and Raymer2 showed that age hardening occurred in a Ti-15 pct V alloy at room temperature after it was quenched from a temperature in the ß-phase region. During a recent investigation of the heat-treating characteristics of binary Ti-Mn and Ti-Cr alloys at Battelle, further evidence of low temperature aging was found. Appreciable hardening occurred in some of these alloys at aging temperatures as low as 212 OF (100oC). Indeed, the brief heating period employed for mounting metallographic specimens in bakelite resulted in hardening. It was felt that further information on this low temperature aging phenomenon would be of general interest in view of the large amount of work currently being done on titanium alloys. The alloys examined in this investigation were arc-melted in a water-cooled copper crucible as 3/4-lb ingots. Du Pont Process A sponge was used as a base material. The arc-melted ingots were forged at 1700" to 1800°F (927" to 982°C) and hot rolled at 1450°F (788°C) to 14 gage (0.064 in.) sheet. Small specimens were heated in argon at 1742°F (950°C) for 30 min and quenched in various liquid media or air cooled. They were then mounted in a room-temperature-setting resin and given a metallographic

Jan 1, 1954

(Under this heading will be published notes sent to the Secretary of the Institute by members or other persons. ) A member, technically educated, with 20 years' practical experience as engineer, assistant superintendent, superintendent, and manager of large mines and mills on construction and operation, also experience in mine examination, is open to engagement. Metallurgist of 18 years' experience in Mexico with large plants is open to engagement. Last position, superintendent of copper smelting works. Best line, copper and lead smelting, but also experienced in mine valuation and ore-treatment investigation work. Speaks Spanish. A member of the Institute and graduate mining engineer with 10 years' experience in the Lake Superior copper district, also practical experience, desires position as superintendent or manager. Member, graduate mining engineer, experienced in mine and mill work, geology and field work, one year in the hydrometallurgy of copper, is open for engagement Aug. 15. A member, at present in the Southwest., desires a position as assistant superintendent or assistant manager with a mining company operating in Washington or Alaska. Experienced assayer and engineer. A member, technical graduate, with nine years' mining experience as assayer, engineer, foreman, manager's assistant, and superintendent of large development and operating mining companies in the United States and Mexico, is open for engagement. A member, technical graduate, 33 years of age, 11 years' experience as chemist, metallurgist and superintendent of lixiviation plant and in charge of construction of cyanide mill, desires position as assistant superintendent or superintendent of mining or milling company in United States or Canada. Young man, technical graduate, two and a half years' experience in chemical laboratory, desires position as chemist.

Jan 9, 1913

By H. O. Hofman

THE leading antimony mineral is stibnite. In smelting stibnite ore two processes are available, precipitation and roasting-reduction. The former is suited only for high-grade ores. As low-grade ores are more common than high-grade, roasting-reduction is of greater importance than precipitation. In the roasting process the aim may be to leave the oxidized antimony in the ore, or it may be to volatilize as much of the antimony as possible, collect the volatilized oxide as a rich intermediary product and smelt it for antimony, leaving the gangue poor enough to be considered a waste product. Whichever way the roast is conducted certain difficulties inherent in stibnite are encountered. These are: 1. The low melting point of stibnite which; according to Pelabon,1 is 550°C., according to Wagemann2 540°C., and according to Borgström3 546°C. 2. The ignition temperature: According to Friedrich,4 stibnite, if heated in air, begins to oxidize at 290°C. if the size of a grain is 0.1 mm. in diameter; at 343°, if 0.1 to 0.2 mm.; and 430° if 0.2 mm. 3. The fusibility of a mixture of Sb2S3 and Sb203 which in the form of kermesite (Sb2S3)2.Sb203 melts at 517°C.5 4. The volatility of Sb2S3 and Sb203, for which no numerical data appear to exist, although practical experience has shown that they are volatile at low temperatures.

Jan 1, 1916

By Ashbel Welch

Ashbel Welch, Lambertville, N. J.: Dr. Dudley has given the wear of steel rails under four different conditions. He arrives at the conclusion that the softer rails, or those that from their composition ought to be softer, wear better than the harder. But there is another condition which has an important bearing on the subject, and should not be overlooked,—the weight on a wheel. With the lighter weights of the past, the softer rails may have worn best; with the heavier weights of the future, the harder may wear best. Weights will probably be increased up to the capacity of steel to bear; then doubtless the harder steel will wear best. A leaden rail with ten pounds on a wheel might carry millions of tons, but with one hundred pounds on a wheel, it would be destfoyed by a few thousand tons. So in the days of iron rails, my experience was that the softer rails under light machinery stood better than some of the harder; but under heavy machinery the softer were much the most rapidly destroyed. It is doubtless the same with steel. The pounding motion of the wheels loosens or spreads the particles of a thin film of steel; the pull lengthwise on the rail de-

Jan 1, 1881

By B. H. Bergstrom, C. L. Stevenson

In any process wherein materials must be pelletized, a crucial period exists during the interval between the manufacture of the green pellets and their subsequent heat treatment. The pellets must possess sufficient strength and plasticity to withstand conveying and sizing. Also, they must be neither excessively brittle nor excessively plastic when placed in a bed on a traveling grate for heat treatment. An acceptable pellet, in the event sufficient forces are applied to cause its fracture, will merely split into two or three large fragments which would not drastically alter the permeability of the pellet bed. However, when brittle pellets are broken, they shatter so that the resultant fine particles either decrease the perimeability of the bed or become entrained in the gas stream and thereby cause dust problems. On the other hand, excessively plastic pellets may not break at all but may merely flatten. This would seriously hamper bed permeability. In the past, pellet evaluation has usually been left to the creative and artistic talents of the balling operators. A multitude of techniques have evolved, of which the most common is the simple compression test. For this test a hand-operated device loads single pellets to fracture, but reliability is strictly operator- dependent. Probably the next most common test is the drop test, which is conducted according to several different procedures. This is an important quantitative test for estimating the amount of handling a pellet will withstand. There are many other tests, such as pinching a pellet between the thumb and index finger, but none are capable of producing reproducible results.

Jan 4, 1962

By Archer E. Wheeler, Milo W. Krejci

There are two general methods in use for the production of metallic copper from matte which are worthy of consideration : (1) the Welsh blister process, and (2) the converter process.' As practically all of the copper produced to-day is made in converters, we will give a brief outline of that process before proceeding with the special subject of this paper. Matte may be roughly defined as a mixture of the sulphides of copper, iron, nickel, silver, etc. In the converter process this is blown up to metallic copper in a modified type of Bessemer converter. The conversion of matte consists mainly in, (1) the removal of sulphur in the form of SO2, and (2) the slagging of the iron. With this brief statement we come to the two subdivisions of the process of converting mattes: Converting with acid linings. Converting with basic linings. Converting with Acid Lininys, This is carried out by lining the converter with siliceous rock or ore, which performs two functions: It protects the iron shell of the converter from the molten charge, and it furnishes the silica for combining with the iron as it is oxidized from the matte, to form a ferrous silicate. It follows from the second of these functions that this siliceous lining must be replaced from time to time, and in practice it has been necessary to reline converters every 8 to 40 hr., this time varying in different plants and even with different linings in the same plant, the life of a lining depending upon the grade of the matte treated, and upon the composition, the thickness, the tamping, and the drying of the lining.

Jan 1, 1914

By Earl A. Gulbransen, Kenneth F. Andrew

DRY oxidation of zirconium has been studied by several groups.'" The present work extends our early study1 to the high-temperature studies of Cubicciotti2 and Belle and Mallett.8 ulbransen and Andrew1 showed that the parabolic rate law fitted the 2-hr experiments between 200" and 425°C after an initial deviation. An energy of activation of 18,200 cal per mol was calculated. Cubicciotti,' in a study between 593" and 880°C, showed that the parabolic rate law fitted the data and an energy of activation of 32,000 cal per mol was calculated. In contrast to these studies on sheet specimens, Belle and Mallett3 studied the oxidation reaction on rod specimens and found a cubic rate law to fit the data.

Jan 1, 1958

By Milton H. Ward

INTRODUCTION Historically, planning a mine involved the economic decision of whether to mine by open-pit methods or underground methods. The method selected was influenced by a number of factors, including size, tenor, and location of the deposit. If the project could not be justified by either underground or open-pit practices, it remained in fallow until economic conditions changed or technology advanced. Technology has advanced and the mining industry now has another option, that of in situ leaching. This method is on the threshold of becoming a commonly used alternative for production in many types of metal and mineral deposits. It will be utilized as the primary method for developing an ore body or as an adjunct to open-pit or underground operations. The following considers application of the technique to a deposit that had been partially exploited by open-pit methods. HISTORY The Big Mike Copper Mine is located approximately 30 miles south of Winnemucca, in Pershing County, Nevada. Interest in the property dates from the turn of the century, but little exploration was undertaken until the mid '60s. In 1967 Cerro Corporation acquired the property and initiated a major drilling effort. Ranchers Exploration obtained the property after this exploration program in late 1969 and confirmation drilling was undertaken. The deposit was delineated and it was determined that reserves amounted to about 100,000 tons of 10.0% massive copper sulfide ore and 700,000 tons of 2 .O% mixed oxide-sulfide ore. The ore body was a lenticular deposit, dipping at 50°. The massive sulfide mineralization was chalcocite and

Jan 1, 1974

By E. T. Dumble

THE development in the Gulf Coastal Plain for the year 1923 was entirely devoid of any spectacular feature and was considerably less than that of 1922. No large fields were discovered and the principal advances lay in the extension of the old fields and the finding of a new dome and other possible producing structures, which, however, so far, have given only small wells. While the production of some fields, such as those at Hull and Orange, was materially increased at times by comparatively large wells, the output as a whole shows a marked decrease over that of the preceding year. TABLE 1.-Production by Fields in Gulf Coastal Plain in 1923 FIELD BARRELS FIELD BARRELS Anse La Butte 16,942 Jennings 212,376 Barber's Bill 172,660 Markham 39,290 Batson 391,857 North D ayton 74,983 Big Hill (Jefferson County) 13,853 Orange 5,311,995 Blue Ridge 332,445 Pierce Junction 332,565 Damon Mound 822,355 Richmond (Big Creek) 17,545 Edgerley 176,964 Saratoga 700,661 Goose Creek 6,251,761 Sour Lake 2,091,961 High Island 19,018 Spindletop 309,315 Hull 7,732,139 Vinton 2,134,430 Humble 2,449,744 West Columbia 6,598,589 36,203,448

Jan 3, 1924

By W. H. Adams

Among the persistent experimenters of the present century no one man is more widely and favorably known in the metallurgical world than the late Peter Spence of Manchester, England, to whom we are indebted for many of the successful processes in the manufac ture of acids and alkalies, and for much of that perfection in me chanical detail which goes so far towards insuring success. For the past twenty-five years—a period covering the greatest changes in soda-processes and a revolution in acid-manufactures ef fected by the substitution of pyrites for brimstone—Mr. Spence was constantly engaged in perfecting the plant for the economical treat ment of pyritous ores; and no text-book has been complete without reference to his many inventions, patented or otherwise. The results of his labors for the past six years were not given to the public, by reason of the active competition existing among man ufacturers on the continent of Europe and in Great Britain ; but it was well known and conceded that the crowning triumph of his .life had been achieved in the successful working of his automatic desulphurizing furnace, which mechanically calcined "smalls" or finely crushed pyrites—the bugbear of all chemical manufacturers. That he was met by many delays and disappointments, and that

Jan 1, 1885

By Charles E. Nelson

In considering the types of scrap that are processed into secondary magnesium, it is important to point out that the greatest proportion of this material is fabrication, foundry and machine shop scrap that is generated during the conversion of magnesium products into the finished article. This material, then, is largely of the same composition and quality as the original ingot or heat of metal except as it may be mixed with other compositions or metals in the fabricating process. Insofar as such materials can be processed back into secondary ingots or final products which meet the composition and property standards required of the original virgin stocks, then it seems reasonable that such products are fully equivalent to the primary products. With these premises then, it is the intent of the present discussion to consider briefly some of the methods whereby scrap may be generated, segregated, shipped, and processed in such a manner that the final products will be equivalent to virgin materials. Some information on the effects of impurities will be given in order to aid in the evaluation of these products. SCRAP GENERATION The method by which scrap is generated serves in a rough way to classify the resulting materials in terms of how they may be handled and recovered. These methods will be dealt with briefly. Machining operations such as milling and turning undoubtedly provide the great-

Jan 1, 1943

By Walter C. Labys

INTRODUCTION Interest in multicommodity stabilization schemes has increased recently for several reasons, a most important one being the experienced wide swings in primary commodity prices. These prices rose sharply between mid - 1972 and end - 1974 giving commodity exporting countries an opportunity to gain sizeable increases in export earnings. But since then, prices have tumbled and these countries are searching for a means to stabilize if not to increase their earnings. While this problem is particularly serious for developing countries, the developed countries are concerned about the impending upward price swing, which would increase inflation before recovery from the world recession is assured. As a direct consequence of the emergency meeting of the U.N. General Assembly devoted to commodity problems in April of 1974, interest has been renewed in the Keynesian (4) plan for an international multicommodity buffer stock program. In particular, UNCTAD (8) is designing an integrated commodity scheme to be discussed within that body. In terms of approaches that have appeared in designing such a program, none exist which relate to the interpretation of the independence and interdependence of prices of the commodities of interest. Typical criteria for selecting commodities for the scheme have included their importance in world trade, their particular origin from developing countries, and their feasibility for storage. But the financial management of a multicommodity buffer stock requires a consideration of commodity prices, yields, and risks as does as any portfolio of assets. The approach which we take in this study is that of application

Jan 1, 1977

By George S. Miller

Now that low-carbon steel is manufactured successfully in large quantities by the Bessemer process, and threatens to displace wroughtiron for nearly all purposes, it becomes interesting to find how its Specific gravity compares with that of wrought-iron. The general name "steel" is retained in this paper to designate that metal made by the Bessemer process, which might be more properly called " ingot iron." But the former name seems to be quite firmly established in the iron trade. This steel offers many inducements to the manufacturer of architectural iron, by reason of its hornogencity, and the large masses in which it may be readily moulded. The steel from which these determinations have been made, was produced in four-ton heats and cast into ingots of about 3100 Ibs. weight, having an average section 14'' by 14". These ingots were rolled in a blooming-mill to a section about 24" by 14", cut into slabs and rolled in a plate-mill to a plate .065" to .165" thick, and about 1411 in width. The specific gravity was obtained from pieces of this plate. The metal showed by analysis .10 to .12 per cent. carbon,.33 to .45 manganese,.060 to .072 sulphur,.075 to .082 phosphorus, and .010 silicon. The samples were not annealed, but were brought to a bright surface with a file. All figures given are averages of not less than three determinations on separate pieces from the same plate. The variation in the figures from which the averages were made in no case exceeded .015.

Jan 1, 1886

By T. M. Berry

In the past few years changes have taken place in shaft sinking. Progress has been made with types of machinery designed, developed, and made available to shaft sinking contractors. This is particularly true of drilling and mucking equipment. Compared with conventional clamshell loading, mucking or loading with a crawler-mounted overshot loader is a new technique for shaft work. There are several methods of clamshell loading. Dravo Construction Co. mounts an air tugger on the clamshell to operate the closing line. The load, or holding line, is attached to the hoist of a crane or whirler at the shaft collar. The clamshell is raised or lowered by the hoist when a signal is given by a bell or light system operated by men at the bottom of the shaft. Two men control the drift of the clamshell with tag lines, pulling it to any position in the shaft for loading, or over the shaft muck bucket for emptying. One man operates the air tugger to open and close the clamshell by means of two lines attached to the operating air valve, just as reins are used to drive a horse. One man operates the signal telling the hoist operator when to raise or lower the clamshell. This method requires two hoisting lines in the shaft-the line from the mine hoist that lifts

Dec 1, 1956

By Theodore Nagel

Fuel-oil, natural gas and coke oven gas, producing the higher temperatures of open-hearth current practice, have been gradually displacing producer gas the lowest cost fuel for open hearth operations. The lower temperatures of combustion products from producer gas is caused by nitrogen dilution. Practical Application of Combustion Thermochemistry One pound of carbon burned to CO produces 3,960 B.T.U. and one pound of carbon burned to C02 produces 14,140 B.T.U. The second unit of oxygen uniting-with gasified car-bon (-CO) produces (14,140 - 3,960) 10,180 B.T.U. which is;(10,180 - 3,960) 6,220 B.T.U. more heat than produced by the first, unit of oxygen forming CO by uniting with solid carbon. A review of the relative combustion heating values of commercial gaseous fuels reveals CO requires a minimum of air for combustion, and because of minimum nitrogen dilution and the high thermal release from CO higher temperature combustion products are produced from CO than from natural gas or from coke-oven gas under similar combustion conditions. Inert nitrogen diluent lowers the calorific value of fuel gas and its diluting effect is cumulative in lowering the temperature of the products of total, combustion. It is not only logical but, practical in partial combustion, converting bituminous coal to gas, to generate the gas, with reduced nitrogen dilution.

Jan 1, 1936