Search Documents

By R. D. Fisher, A. G. Metcalfe, F. A. Crossley

AN investigation of the application of magnetic stirring to the consumable arc melting of aluminum and nickel demonstrated that grain refinement could be obtained when there was sufficient stirring force. Also, it was found that grain refinement could be obtained in aluminum by alternately reversing the polarity of the current through the magnetic stirring coil. The effect of the latter was to periodically reverse the direction of rotation of the molten metal.' Because of their promise, these findings were applied to conventionally cast aluminum. Shortly after this work was begun, Kondic2 reported experiments in which aluminum cast with 40° C (72° F) of superheat exhibited a grain size of 10 to 20 grains per cm2. When interrupted rotation was applied during solidification by mechanical means, a grain size of 800 to 1000 grains per cm2 was obtained. Magnetic Stirring Applied to Conventional Casting— The applicability of magnetic stirring to producing grain refinement in conventionally cast metal was evaluated in the following way. Three pounds of aluminum were cast into a clay-bonded graphite mold. The mold was surrounded by a magnetic stirring coil of 1000 turns. A direct current of 200 amp was passed through the casting by means of a graphite electrode which was immersed from the top. A current of 5 amp was passed through the stirring coil. The aluminum (1100 or 25) was superheated to 1600° F (871° C) and fluxed by passing chlorine gas through the melt for 2 min prior to casting. Two additional castings were made for comparison: 1) a conventional casting of metal superheated to 1600° F and 2) a similar casting through which 200-amp current was passed during solidification, but without current in the magnetic coil. Macrosections of these three ingots are shown in Fig. 1. Very remarkable grain refinement resulted in the magnetically stirred casting. It may be noted that the casting through which 200-amp current was passed has a coarser structure than the conventional casting. It would appear that this is due to the additional heat input generated by the current to the former casting. Mechanical Rotation Applied to Conventional Casting—A casting temperature of 1600° F was used throughout. Some 1 1/2 -lb castings rotated at 150 rpm were predominantly columnar with small areas of coarse, equiaxed grains close to the lower mold wall. Following these, a series of 3-lb castings was made. Macrosections of these ingots are shown in Fig. 2. The imposed rotational speed was 250 rpm. Turbulence or acceleration in the solidifying liquid was the significant factor. Fine grain size resulted in the material solidified during the period of acceleration of the liquid to the imposed rotational speed. When uniform rotational motion was achieved, the grain structure reverted to columnar. The final casting shown in the lower right-

Jan 1, 1962

By Maurice Rey, H. Brevers

Through circumstances connected with the war, the senior author lost his records, therefore it has been impossible to include numerical data in this paper. The arsenical quicksilver ore investigated had been roasted, with poor metallurgical results. The vapor-tension temperature curves of mercury and arsenious trioxide are similar, and the arsenical compound hampers the coalescence of mercury drops in the condenser and is the cause of large stack losses. The ore was a gray limestone carrying small amounts of carbon and mineralized with cinnabar and two arsenic minerals, realgar (As2S2) and arsenopyrite (FeAsS). The proportion of realgar often exceeded that of cinnabar; the proportion of arsenopyrite was smaller. The grade of the ore varied between 0.8 and 4 per cent Hg. The problem was to make a high-grade mercury concentrate, as free from arsenic as possible. The water used throughout the testing was hard, having a pH of about 8. Flotation of Realgar Realgar showed a very strong tendency to float. It formed a film at the surface of the pulp and floated in abundance with only pine oil. Therefore an attempt was made to float the realgar before the cinnabar, but this was not very successful; the percentage of mercury in the realgar concentrate could never be brought below 2 or 3 per cent. Cinnabar slimed easily and floated with pine oil, so that some of it always accompanied the realgar. There was also the question of the cinnabar-arseno-pyrite separation. On further investigation it was found that realgar can be floated not only with pine oil but even better with a combination of hydrocarbons and pine oil. Washing the ore with ether revealed that it contained hydrocarbons, which helped to float the realgar. In this connection it belongs to the same class as carbon, sulphur and talc. It can be floated also with a xanthate, when activated by a heavy-metal salt. The conditions favoring the two types of flotation are opposed, as activation by a copper salt facilitates xanthate flotation (in fact, is even necessary to it), whereas it hinders pine oil and petroleum flotation. One type of flotation can be termed non-polar and the other polar, a distinction that has been stressed in a previous paper.' Depression of Realgar and Flotation of Cinnabar Many chemicals were tested in an attempt to float the cinnabar and depress the realgar. Finally starch rendered soluble with caustic soda was tried, also several grades of commercial soluble starch, and dextrin was found to be the best and the most convenient reagent. Several of these starch preparations have a strong flocculating effect on the pulp, which is a distinct disadvantage. Dextrin, with its low flocculating power, is excellent. It is noteworthy that starch preparations are also depressants for carbon and talc, so that the fact apparently has a general

Jan 1, 1943

By John R. Spencer

A capillary tube variable volume cell is described, which has operated satisfactorily over a range of 100°F and 3,500 psi to 550°F and 1,500 psi. The cell contents are entirely visible over the length of the capillary with the exception of a space at the top amounting to three per cent of the total volume. Observations on the critical behavior of simple systems have been greatly facilitated by the apparatus, it being possible to establish the critical conditions for a particular mixture in the course of a day's run. INTRODUCTION Many types of apparatus have been designed for obtaining data on the phase relationships of hydrocarbon systems. Such apparatus can in general be subdivided into two classifications; (l), indirect measurement of phase volume, and (2), direct visual observation of phase volume, each of which has outstanding advantages and disadvantages. Indirect measurement of phase volume requires the use of rather elaborate apparatus including internal probes in which are located the device for determining the locus of the interface between phases. Such equipment is by its very nature costly, and is complex from the standpoint of operating technique. Probing techniques can be used, however, over wide ranges of temperature and pressure with a high degree of reproducibility. Apparatus for visual observation of phase behavior obviously has the advantage of enabling the experimenter to see exactly what takes place, but because the material to be tested is contained in a cell constructed of both metal and glass, is limited severely as to the temperature range of operation. Furthermore. the maximum pressure usually is limited by the choice of material used for sealing the glass to the metal, and by the strength of the glass itself. In the interest of increased efficiency of observation, as much of the cell as possible should be visible to the eye. Glass capillary tubes have been used successfully but have always given difficulty at the metal-to-glass seal. An apparatus has been devised to overcome the problems of sealing and resistance to temperature effects that have heretofore been the limiting factor with glass apparatus in the observation of phase volumes at elevated temperature and pressure. APPARATUS The objective which dictated the general arrangement of the apparatus (Figs. 1 and 2) was simplicity of operation. The air bath, A, was constructed of an iron framework to which was attached approximately one inch of glass wool bats which were covered on the outside with "Masonite." A roughly octagonal center piece was installed to provide forced circulation of the air by the fan, B, past the heaters, D, cell, F, and thermoregulator, C, respectively. The entire top of the box is removable to facilitate charging of the cell and to permit easy maintenance. Two windows are provided before and behind the cell to allow the operator to observe the contents against the background fluorescent light, E. The heaters,

Jan 1, 1951

By L. L. McMurray

Ilmenite is the most important raw material for manufacture of titanium dioxide.' Industrially, several other products are made from ilmenite, the most important of which are: ferro titanium, ferro carbon-titanium, copper-titanium, titanium carbide and titanium nitride. The production of titanium metal is still in the laboratory stage because of the difficulty of extraction and as yet no important application for the metal has been found. Ilmenite has received considerable attention as an industrial raw material. Imports of ilmenite concentrates for the first nine months of 1941 were 156,737 short tons, the chief source being Travancore, India.2 Domestic produttion of ilmenite has heretofore been confined to Amherst and Nelson Counties, Virginia, where a complex rutile, ilmenite, and apatite ore is mined and treated to utilize all three of these minerals. A recent report3 has described development of the large titaniferous magnetite ore body at Tahawas, New York, where it is expected that 800 tons of ilmenite concentrates, containing 48 per cent TiO2 will be produced daily. Additional domestic production is expected from a large ilmenite deposit recently opened in caldwell county, North carolina. Flotation tests indicate that a high-grade concentrate containing 53 per cent TiO2 can be made from the North Carolina ore. Prospecting of domestic ores in other areas has been reported.' It appears that increased domestic production of ilmenite may well save considerable shipping space so vitally needed in these times. The composition and chemical structure of pure ilmenite is given by Dana as: FeO, TiO2; Ti, 31.6 per cent, Fe, 36.8 per cent, O2, 31.6 per cent. This composition is variable in that some iron or titanium may be replaced, giving a variable iron-titanium ratio. As an example, the iron-titanium weight ratio of ilmenite in Caldwell County, North Carolina, has been determined to be 0.94 (using 97.1 per cent ilmenite concentrate obtained by heavy liquids on minus Iso-mesh ore) compared with theoretical 1.16. No rutile was noted in this ore to account for the low value. This North Carolina ore is free of magnetite, which is a common associate of ilmenite ores. In view of a large potential production from North Carolina, the Tennessee Valley Authority conducted a study of methods of concentration of that ore, of which the results are reported herein. The Ore Five samples of Ore were taken from the deposit at various exposed locations and were mixed for the study and testing. An attempt was made to proportion the amount of weathered and unweathered portions in making the composite sample, so as to approximate actual operating conditions. An examination of representative specimens of the sample showed the following general facts: 1. The black mineral comprising nearly 70 per cent of the ore is ilmenite.

Jan 1, 1948

By R. Scot Clark

The reactively sputtered silicon dioxide capacitor -was developed for use in the monolithic integrated circuit, thereby requiring the capacitor to be fabricated on an oxidized silicon slice. The silicon dioxide film is formed by reactively sputtering silicon in a 50 pct Ar-50 pct 0, atmosphere and the physical properties are indistinguishable from silica. A practical upper limit of capacitance per unit area of 0.25 pf per sq mil is reached with the capacitors fabricated from the Si0, film. Methods shown to enhance this value are double stacking the thin-film capacitors and addition of aluminum to the silicon cathode during sputtering to form an aluminosilicate dielectric. A major contribution to the field of diffused integrated circuits would be the addition of auxiliary passive devices for replacement of diffused passive devices which are currently being fabricated for many integrated circuits. This accomplishment would increase the flexibility of the diffusion process in order to concentrate more on transistor parameters rather than on fabricating diffused resistors and capacitors. To pursue this technique, a thin-film SiOz capacitor was developed which has _ proven applicable to many integrated circuits. Although the SiOl capacitor has an application, the major deterrent from extending the integrated circuit into many useful areas such as low-frequency linear application is the low dielectric constant of SiO, and the low usable capacitance in an integrated circuit. This paper will cover the sputtering techniques used for forming the SiO, film, the physical and electrical properties of sputtered SiO,, and yield information concerning the application of these capacitors to integrated circuits. REACTIVE SPUTTERING Reactive sputtering is simply the sputtering of a metal or semiconductor in glow discharge in the presence of a reactive gas. The material to be sputtered is seen in Fig. 1 as the cathode of the system and is bombarded with positively charged ions of the ambient gas. In this investigation, the ambient gas is composed of 50 pct Ar and 50 pct O2 at a pressure of approximately 2.5 X l0-' Torr. The ions are accelerated toward the cathode in the cathode dark space by the electric field and upon striking the cathode effect a momentum energy transfer to the surface atoms. The transferred energy is sufficient to dislodge a surface atom or atoms and these particles diffuse through the glow discharge to the collector or anode. Several mechanisms of oxidation in the reaction chamber can be considered during reactive sputtering. 1) The surface of the cathode is oxidized and the oxide is subsequently sputtered. 2) Oxidation and sputtering occur simultaneously. 3) Sputtering of the cathode material is followed

Jan 1, 1965

By Nicholas J. Grant, H. C. Chang

EMPHASIS on the importance of grain boundary sliding as a mode of deformation at elevated temperatures has been presented elsewhere.' The extent to which boundary sliding occurs under certain creep conditions has been determined for high purity aluminum2,3 and aluminum alloys.' In general, boundary deformation extends quite far into the adjoining grains, resulting in a rather wide band of deformation along the grain boundaries. This has led some investigators to doubt that grain boundary sliding consists of shearing along the boundary surface; it has been contended instead that boundary sliding is a result of concentrated slip in the neighborhood of the deformed grain boundaries."' The purpose of this note is to present evidence that grain boundary sliding takes place by a bulk shear process. gh purity polycrystalline aluminum, wherever and whenever there is grain boundary sliding, boundary migration and concentrated deformation along both sides of the deformed boundary are associated with it. Therefore, it has been rather difficult to obtain unambiguous evidence of boundary sliding. On the other hand, it would be expected in certain alloys of aluminum, when tested under particular conditions. that the severity of the interfering effects of boundary migration and concentrated deformation along the deformed boundary might be reduced. Current research in this laboratory' shows that a 20 pct Zn-A1 solid solution alloy fractures in an intercrystalline manner during creep at 500°F with a small total elongation of not more than about 14 pct, and that it does so with extremely limited grain boundary migration. Accordingly, this alloy was chosen for the present study. The experimental procedure was similar to that used in previous work and has been presented elsewhere.' Two parallel flat surfaces were milled from a round specimen. The gage portion of the specimen was 1 in. x .09 in. x .17 in. The specimens, which were annealed at 1030°F for 24 hr, showed two to four grains across the width of the test bar. The specimens were subjected to creep at 500°F at stresses of 2000 to 5000 psi. The rupture times were from 10 sec to 3 hr. Appreciable boundary sliding occurred in all the tests. A typical example of boundary sliding is shown in Fig. 1. (The tension axis is vertical in the micrographs.) Sliding has taken place along the boundary between grains A and B unaccompanied by important boundary migration. The sharpness of the offset at the triple point can be clearly seen in grain C. As a result of sliding along the boundary between grains A and B, a new boundary surface between grains A and C was created. The offset at the triple point is about 0.07 mm. This boundary sliding is accompanied by the formation of rather sharp kinking bands and, of course, slip on several slip systems in grain C. This type of deformation has been referred to as fold formation' in previous work with high purity aluminum.

Jan 1, 1957

By John Wulff

IN a previous paper Burwell and Wulff1 have shown by electron diffraction studies that allotropic transformations can be induced in 18-8 stainless steel by polishing to a depth of about 5 X 10-5 cm. The development of a successful etching technique, which removes accountable amounts of metal from the surface without pitting and without changing the root-mean-square profile as measured with an Abbot profilometer, led to the application of the whole technique and material to an investigation of various mechanical methods of surface preparation, such as grinding, lapping, superfinishing and cold-rolling. Ideally suited to such a study is 18-8 of low carbon and nitrogen content. The material can be heat-treated to produce a coarse-grained single-phase structure. On cold deformation there occurs not only a reduction in grain size but, at regions of maximum stress, a change of face-centered material to body-centered material, provided the metal is worked below about 200°C. When worked between 200° and 415°C., diffraction studies evidence a reduction in grain size without the appearance of any new body-centered ferrite. Ferrite, which can be referred also to strains induced by carbide precipitation, is evident when the material is worked at temperatures between 415° and 800°C. Stainless steel is advantageous because the usual surface-finishing operations do not readily oxidize it to any appreciable depth. In order to produce detectable oxide films on the surface of austenitic 18-8 in a time equivalent to that required to produce, for example, a fine ground finish on ½ sq. in., the sample must be held in a furnace or oxygen stream above 600°C. By using longer heating times, it is possible to achieve measurable oxide films on samples whose surface temperatures exceed only about 250°C. EXPERIMENTAL PROCEDURE The apparatus, material, and technique described in the previous paper1 were employed in this investigation. Samples of 18-8, 1 by 1 cm. by 4 mm., were carefully annealed in the austenitic range to produce a coarse-grained structure. They were then quenched and pickled to remove scale. On a lapping machine of the Graton2 type, both sides of each sample were polished to a flatness of 1/6 a wave length of sodium D light. Thereafter they were electrolytically etched to remove at least 1 X 10-3 cm. of the surface, a depth that is well below that of any deformations induced by surface preparation. Samples of this material, carefully mounted in steel holders, were then sent to various industrial organizations known for special finishing techniques. In the instrument shops at the Massachusetts Institute of Technology check samples were finished by the same methods, as far as they were available. Abbot profilometer3 readings were made on all the samples, which were then carefully degreased in double distilled benzine and alcohol, dried in a hot-filtered air blast, and kept in a desiccator. Suc-

Jan 1, 1941

By J. C. Motz

Introduction The variations in crushing plant design seen during the past 30 years provide a valuable source of information and experience from which one can select the optimum arrangement for a specific requirement. The purpose of this paper is to examine some specific equipment configurations as they relate to operating efficiency, plant availability and final product size in the form of mill feed. Due to the varied ore properties, physical space limitations, size of ore body and financial resources, there is no single crushing or grinding flowsheet that is best. Since energy costs have risen dramatically during the recent past, it became obvious that significant savings are possible by selecting equipment and a circuit which offers low power requirements balanced with low wear metal and installed equipment costs. Relatively clear and measurable are the metal and maintenance costs and the ever increasing cost of energy. Metal costs in the form of crusher liners have not quite doubled in the last 20 years, while power costs have increased by a factor of four or five, depending on the region considered. Estimates made only a few years ago on the increased cost of energy are obsolete in view of the recent unstable conditions. Since power is therefore becoming the largest cost area, it behooves us to investigate potential cost saving methods in the form of lowering the KWH/Ton of crude. Crushing To reduce run-of-mine to mill feed requires reduction in a series of stages. The physical size and power requirements of a crusher capable of reducing hard rock vary depending on the application. Extended experience in most crushing plants show that a minus 19MM (3/4 in.) rod mill feed can be and is being produced in three stages of crushing. In the majority of cases, the last crushing stage is closed circuited using anywhere from 19MM (3/4 in.) to 14MM (9/16 in.) slotted openings on the sizing deck. In some copper concentrators, the mill feed is all passing 13MM (1/2 in.) using three stages of crushing and 14MM (9/16 in.) square openings on the closed circuit screens. It was felt by some that crushing to this fine size is only possible if the ore is friable and is relatively soft in comparison to the harder ores. Our results show that some of the copper ores are as hard as taconite and are crush-

Jan 1, 1982

By L. C. Reese

The ultimate resistance against a rigid cylinder which is moved laterally in a cohesionless soil is a function of the geometry of the cylinder and the properties of the soil. An approximate method is developed for computing this resistance and is tested against results of laboratory experiments. Satisfactory agreement between the method and experiment was obtained. Not only was the ultimate resistance against the cylinder measured, but measurements were made of the shape of the rupture surfaces. These measurements should allow the development of a more rigorous computation procedure. INTRODUCTION A critical aspect in the design of offshore drilling platforms is assuring the stability of the platform during a hurricane. The large horizontal loads from waves and wind make a severe loading condition. Piles are generally employed as the foundation since they can be effective in resisting both horizontal and vertical loads. Spuds are sometimes used with a mat foundation, where the spuds are designed principally to resist horizontal loads and the mat designed principally to resist vertical loads. The research reported in this paper is related to one aspect of the problem of laterally loaded piles or spuds in sand. The complete solution to the problem of the laterally loaded pile in sand would require the prediction of soil resistance against the pile as a function of pile deflection; only the ultimate resistance against short piles is considered in this paper. A considerable amount of additional research will be necessary in order to obtain a complete solution to the problem of the laterally loaded pile in sand; however, the work reported here should be useful as a guide in the performance of some of the additional research. ULTIMATE LATERAL RESISTANCE AGAINST A LONG FALL IN SAND To aid in the understanding of the theory which is developed for a cylinder, the theory for earth pressure against a wall is reviewed. In Fig. l(a), a long wall of height H is shown embedded in soil. Soil resistance will develop as the wall is deflected, and the soil resistance will increase with deflection until some limiting value is reached. In this discussion, and those following, it is assumed that all points on the wall deflect equal amounts. A possible shape of the real curve which relates soil resistance to deflection is shown by the dashed line in Fig. l(b); however, as a means of simplifying the discussion, an idealized curve (shown by the unbroken lines) is drawn. If such a wall as this were furnishing the horizontal support for an offshore structure, the dashed curve in Fig. 1 would be the information needed in performing a foundation analysis, with the idealized curve possibly being an acceptable substitute. For the idealized curve, the soil resistance is linear with deflection for the early portion of the curve such that

By H. L. Talbot, A. J. Hall, R. S. Young

A METHOD for the chemical differentiation of oxidized cobalt from sulphide cobalt in complex mine and concentrator products is of considerable interest to a number of mining companies throughout the world. At Rhokana Corporation, in Northern Rhodesia, for instance, cobalt is found chiefly in the sulphide form, as carrollite, but a cobalt oxide mineral also occurs irregularly underground, and relatively small quantities in the mill feed from time to time are difficult to detect it visually at the concentrator. The oxide cobalt is not amenable to the sulphide flotation process used at Rhokana and nearly all of it passes into the tailing. The occasional. period when high tailing losses occur with no appreciable change in the cobalt content of the mill feed has naturally been disturbing to the concentrator staff, who had no means of determining whether an influx of cobalt oxide ore or laxity on the part of the mill flotation operators were responsible for these results. A procedure for determining oxidized copper minerals, based on their solubility in dilute sulphuric acid saturated with SO2, has been used for many years in the copper industry. In the presence of cuprite the procedure fails, but otherwise it gives results quite satisfactory for control purposes. Empirical methods for determining oxidized forms of zinc and lead have been proposed, but they are generally unsatisfactory except in isolated cases of a very simple ore. No published procedure for determining oxidized forms of cobalt or similar elements has come to the authors' notice. EXPERIMENTAL PROCEDURE There are obviously two alternatives in attacking a problem of this nature. One is to employ a solvent for oxide cobalt that will not dissolve cobalt sulphide. The other is, to find a substance capable of oxidizing the cobalt sulphide to sulphate, which of course is water-soluble and can then be leached from the water-insoluble oxide cobalt. A representative sample of Rhokana cobalt oxide ore was secured, ground to minus 200-mesh, and carefully rolled to furnish a standard sample for this work. The analysis of this material gave the following percentages: Co, 0.55; Cu, 1.64; Fe, 2.98; S, 0.08; SiO2, 41.42; A1203, 11.20; CaO, 13.82; MgO, 3.80. As a source of cobalt sulphide a similar large sample of carrollite was prepared, analyzing Co, 23.36 per cent; Cu, 27.32; and S, 31.13. This sample of course was not pure carrollite, but was the best obtainable in quantities sufficient for a standard intended for considerable work. It was a pure sulphide sample, microscopic examination showing only carrollite, a little bornite, and gangue, with no visible sign of oxidized ore present. A wide variety of reagents were used in an effort to selectively dissolve oxide cobalt or to oxidize sulphide cobalt to

Jan 1, 1946

By A. E. Martin, Gerhard Derge

IE the molecular constitution of molten slags were better known, the nature of chemical reactions in slags and between slags and metals could be better understood and as a consequence might be better controlled. Constitutional information can be obtained by studies on either the molten or the solidified slags. Valuable as the studies on solidified slags admittedly are for many purposes, especially as control methods in steelmaking, they are always of questionable value in giving information on the molecular constitution of liquid slags. However, the characteristics of molten slags such as viscosity, rates of dilfusion, and electrica1 conductivity can be determined experimentally and interpreted along with other knowledge on slag-metal and slag-gas reactions so as to provide direct information on liquid slags. Metallurgists are accustomed to regard reactions in molten slags as involving only neutral molecules, whereas it is quite possible that ionic constituents are actually involved. For example, the dissociation of calcium silicate usually is represented us Ca2SiO4 = 2CaO + SiO2 although a reasonable alternative would be to write Ca2SiO4 = 2Ca+2 + Si04-4 Such ionic dissociation has been suggested frequently without adequate experimental proof. This paper deals especially with electrical conductivity measurements on slags oi the blast-furnace type. These measurements were made to determine whether or not slags are ionized and, if so, to provide a qualitative estimate of the extent of ionization. Electrolysis experiments that indicate the identity of the ions present are also reported. Since the presence of ions has not been considered carefully in modern slag studies, the relevant literature will be reviewed. Review of Literature In 1906 Aikenl obtained a patent for a continuous process of producing iron electrolytically by passing a direct currenl through a bath of FeO.SiO2 to which iron oxide was added periodically to maintain a uniform concentration. The patent also included the addition of CaO and MgO to the bath to lower its melting point. The silicate melts involved were thus in the same system as basic open-hearth slags but with higher FeO and lower CaO contents. Electrical conductivity measurements were made on some molten silicates by Doelter2 in 1907. Natural silicates, such as

Jan 1, 1943

The amount of coal used in the Colonies before the Revolutionary War was very small, and few records of it can be found, these all being in the Public Records Office in London. The exports and imports for the years 1768 to 1772, inclusive, are shown in Table 3, which apparently do not include the early shipments from the Virginia field. For the three years 1769 to 1771, the imports from Great Britain-their only source-totalled 17,943 tons, or an average of 5,981 tons per year. If the shipments from Richmond for the same period were available, this average would probably not exceed 6,800 tons per year. In Table 4 the shipments of coal from the James River ports for the period 1758 to 1769 are shown. A few of them are re-exports of coal brought from England, but the great majority are undoubtedly of coal produced in Virginia, and the movement was partly to West Indian ports but mainly to Atlantic ports from Baltimore to Portsmouth, N. H. (Piscataway). In Table 5 the data in Tables 3 and 4 are combined, the exports being deducted, and this summarizes all the available data on the amount of coal consumed in the Colonies before the separation from England. As has already been stated there has been a tremendous amount of work done in the Richmond field over a long period of time, many mines were opened and in some cases operated for years, and practically no accurate data remain or have been published to show what was done. There are undoubtedly manuscripts still remaining that will contribute to much of the knowledge of this field, and it is well worth the while of the proper state authorities to collect all the information that can be found anywhere, to enable the future development of these coal deposits to benefit by the record of what was done in the past. Table 22 shows all the methods of shipment from this field, and all of the data available about tonnages moved over each of them. The shipments by the Chesterfield and Clover Hill Railroads are largely duplicated in some of the other columns, but allowance has been made for this in the estimated totals. In addition to the difficulties experienced with similar data for the other states, these Virginia records have one peculiarly their own; it was the custom to allow 5 pecks to the bushel of coal at the pit and only 4 pecks at the docks or at vessel side. In most of the figures it is not stated to which point they apply, and a considerable error may exist due to this cause, although certainly it does not apply to all of them. The notes show the sources of the figures used, and while it is probable that the totals are lower than the actual amounts produced, the data given are the most complete that can now be assembled.

Jan 1, 1942

ASIDE from the John Fritz Medal, in which the Institute participates through its representation on the John Fritz Medal Board, the Institute itself has five major awards to make annually for excellence in technical papers, as follows: The Robert W. Hunt Medal and Prize, The J. E: Johnson, Jr. Award, The Lewisohn Platinum Prize to senior members, and the James Douglas Medal. ROBERT W. HUNT MEDAL AND PRIZE The partners of Robert W. Hunt established a fund which was presented to the Institute at a fitting ceremony on May 27, 1920, to' establish an annual medal and a sum of money to be awarded under the following rules: 1. The award shall consist of two prizes; first of a gold medal, second of a sum of money; a certificate to accompany each prize. The money prize shall not be awarded to a member over 40 years of age, but under unusual circumstances, both prizes may be allotted to one person provided that he is not over 40 years of age. In general it will be understood that the Committee shall award the money prize to the younger men, rather than the medal. 2. The awards shall be made not oftener than once a year to that person or persons contributing to the Institute the best original paper or papers on iron and steel. The scope of the term" iron and steel" shall be determined by the sub-committee considering the awards. In general, papers dealing with the practical side of the subject have preference over those dealing with the theoretical side in recognition. of the fact that Captain Hunt's main contributions to the industry have been in the improvement of production and quality of material. 3. A sub-committee of three to five, including the Chairman of the Iron and Steel Committee, shall be appointed by the Iron and Steel Committee annually to adjudge the award subject to approval. 4. The awarding committee shall submit its report to the Iron and Steel Committee at its October Meeting, and the award be certified to the Secretary of the Institute in time to permit the presentation to be made at the Annual Meeting of the Institute. 5. The recipient of the award shall be ,designated "The Hunt Medallist." This prize is administered by the Iron and Steel Committee. J. E. JOHNSON, JR. AWARD This award is made from the income of a fund of $3000 donated by Mrs. Margaret Hilles Johnson in memory of her husband, J. E. Johnson, Jr., who was a prominent engineer, author of two valuable volumes on iron blast-furnace construction and practise, vice-chairman of the Institute's Iron and Steel Committee, and a frequent contributor of papers to the Institute's Transactions. This prize is administered by the Iron and Steel Committee. The intent of the donor is to encourage young men in creative work in branches of the metallurgy or manufacture of pig iron with which the professional activities of Mr. Johnson were chiefly concerned. The control of the fund and distribution of the awards having been vested in the Board of Directors of the Institute, this Board has made 'the following regulations concerning it:

Jan 1, 1925

This issue presents the first of several articles making up the Bump Symposium, which was held at the 1958 Annual Meeting of AIME. Other Symposium papers will appear in the September issue of Mining Engineering. THE term mountain bump describes the sudden rupture of one or more coal pillars under excessive stress. These bursts occur with varying degrees of violence and sometimes include adjacent strata, especially the bottom rock. Many failures do not develop enough violence to be dangerous and are regarded as an aid to coal production, but severe occurrences are accompanied by tons of flying coal, dense clouds of dust, and excessive gas emission. Such bursts sometimes throw heavy machinery several feet. Major factors to be considered in the problem are the nature of the strata above and below the seam and the depth of cover. Bumps are classified as to their nature, extent of damage, and point of occurrence, e. g., face bump, coal bump, high side bump, low side pavement bump, and district bump. The problem is extremely complex, and it cannot be over-emphasized that preventive measures, if they are to be successful, must be based on a thorough study of conditions in the individual mine. In western Canada, for example, the McGillivray mine, operating in a 9-ft seam at 2000 ft, has experienced severe bumps, but there have been no occurrences in the International mine, which operates in the same coal seam at 2400 ft, where the coal averages 17 ft thick. Differences in conditions governing the operation of these two mines are described in one of the following articles (see page 883). Again, most bumps in coal mines take place along pillar extraction lines, but at the Sunnyside mine in Utah they also occur a long way from active workings and sometimes in virgin territory. It is usual, too, for such failures to occur under fairly deep cover. But at Sunnyside, to cite only one instance, there have been disturbances along the main fault zone under less than 500 ft of cover. All too often conditions favorable to bumps are revealed only by actual mining—at Springhill No. 2 mine, drilling in roof and pavement strata disclosed a 60-ft sandstone bed after operations had started— and where extraction has advanced too far for preventive measures to be incorporated in the mining plan, districts have had to be abandoned. But in an era when premium ores are being rapidly depleted in the face of rising demands, abandonment is not easily justified. There must be systematic planning to eliminate coal mine bumps, insofar as this is possible. As in the Gary district of West Virginia (see page 888) much has been accomplished by planned operations based on known factors in bump control. But even this is not enough. Precise instrumentation is needed to indicate where bumps are likely to occur, and in both the U. S. and Canada stress analysis studies are being carried out with this object in view. These pages reveal the progress being made.

Jan 1, 1959

By William A. Johnson

THE fundamental role of diffusion in many reactions occurring in solid metals has long been recognized, and there have been careful measurements of rates of diffusion in numerous alloy systems, but our understanding of the atomic mechanism by which diffusion occurs is scarcely in an advanced state 1-3 It is doubtful that this mechanism can ever he directly ascertained, rather, all imaginable mechanisms must be examined and the one that is in best accord with such data as can be obtained from suitably chosen experiments should be selected Because of its relative simplicity, diffusion in a system containing only one kind of atomic species-commonly called self-diffusion-is of considerable theoretical interest It may be expected that diffusion theory will not be advanced appreciably until a wide variety of diffusion experiments-of which diffusion in a chemical concentration gradient and self-diffusion are two important types-are carefully performed and inter-compared Aside from the purely theoretical interest in self-diffusion measurements, such studies will be of considerable engineering importance The rate of any process in a pure metal requiring the movement of atoms, of which recrystallization and creep are two familiar examples, will be understood more readily with the aid of self-diffusion data † Self-diffusion implies the diffusion of something into its exact counterpart, the detection of such a process is patently impossible, and it is-necessary to substitute for it the diffusion of one isotope (in this case radioactive) into another isotope (in this case stable) of the same chemical element There is, however, no reason to suppose that a radioactive atom will not diffuse at the same rate as its stable isotope, for all of the isotopes of the same element have exactly the same chemical properties, neither the difference in nuclear energy nor the difference in mass would be expected to exercise an important influence in this phenomenon In this sense, self-diffusion may be thought of as the diffusion of radioactive atoms down a radioactivity concentration gradient, just as usual diffusion is the diffusion of one kind of atone down its chemical concentration gradient The first measurements of self-diffusion ii ere made by von Hevesy4-6 using the radioactive lead isotope thorium B in ordinary lead The recent development of means for producing artificial radioactive elements has made possible similar measurements on gold,7,8 copper,2,9 and zinc 10 11 Many of the data that have been obtained are rather poor, and no adequate reason has been given for their poorness, it appears, however, that the unsatisfactory results are characteristic of the particular experimental procedure employed, and not of self-diffusion measurements in themselves The experimental technique that has yielded the poorer results is the deposition of a thin layer of radioactive atoms on the surface of a specimen and the determination of the rate of inward diffusion

Jan 1, 1941

By Galen H. Clevenger

Equipment for treating lead ores was added in 1905 to a copper plant which the United States Smelting Refining and Mining Co. had built in 1902 at Midvale, Utah, about 12 miles to the south of Salt Lake City. By 1906 the lead section of the plant had been rounded out and consisted of a 90-ton gravity concentrator, fifteen hand-rabbled reverbera-tory roasting furnaces, six blast furnaces, a briquetting plant for handling flue dust and fine ores, a regulus furnace for concentrating the low-grade matte made in the blast furnaces, and a baghouse. The copper section was later abandoned and the plant has been operated for many years exclusively as a lead smelter. Some 45 years had elapsed at the time this plant was built since the first attempts to smelt lead ores in the West, and lead smelting had become a large and profitable industry but fundamentally little that was really new had been developed, which could be embodied in a plant built in this period. Principles and tools to work with had remained much the same as those borrowed earlier from European practice. Capacities had been increased and there were mechanical improvements but hand charging was still in vogue and there was little attempt to recover suspended particles carried out with the furnace gases, beyond settling in flues, which usually was only partly effective for recovery of the coarser particles. Satisfactory roasting and preparation of the fine components of the charge were still partially solved problems. The Midvale plant of 1906 may be regarded as more or less typical of the smelting plant of this period for treating complex western lead ores as distinguished from the recovery of lead from the simple lead ores to the eastward. The operation of a concentrating mill directly in conjunction with a lead smelter was, however, not common practice. The ores treated in this plant have from the beginning come from mines owned and operated by the company or have been custom ores purchased in the territory tributary to the plant. The treatment of custom ores is an important service to the small producer who does not have sufficient tonnage to warrant a plant, and serves to increase the tonnage of the operator of large properties, thereby helping to reduce

Jan 1, 1937

By W. H. Young, P. D. Torrey

The Eastern fields comprise a distinct geological and geographical unit, located in the northern part of the Appalachian geosynclinal prov-ince. In this area are the fields of New York, producing from rocks of Devonian, Silurian and Ordovician age; the fields of western Pennsylvania, where oil and gas occur chiefly in rocks of Mississippian and Devonian age; the fields of eastern Ohio, where oil and gas are obtained from rocks of Pennsylvanian, Mississippian and Silurian age; and the fields of West Virginia, where oil and gas are produced from rocks of Pennsylvanian, Mississippian and Devonian age. Many of these fields are of great antiquity in comparison to the age of the producing areas in a greater part of this country, and consequently in most instances it is impossible to obtain accurate historical statistics. In addition, the records of many of the more recently discovered fields are either unobtainable or are not sufficiently reliable to justify their incorporation in a review of this character. Rather than overemphasize certain fields and areas, where complete records are available, when there are many other fields of equal importance for which statistical data are not available, the authors have made a tabulation of development that does not take into consideration past operations and production. The records utilized in preparing this paper were derived largely from the scout reports of several of the larger companies, which generously made them available to the authors. These were independently tabulated by counties and townships, in order to eliminate as far as possible duplications and, excepting the Clinton fields of Ohio, where many of the smaller wells have not been individually reported, they represent the most accurate information available. Market conditions in both the oil and gas industry were far from favorable during 1932 and in consequence there was a total decline in drilling in the Eastern States, which is 22 per cent less than the number of completions in the preceding year. This decline was not constant over the entire area, as is shown in Table 1. The oil fields of both New York and western Pennsylvania were the scene of renewed drilling activity, which was largely restricted to the water-flooding operations in the Bradford and Allegany fields. Practically no new operations were started, but a certain number of new wells

Jan 1, 1933

By P. D. Hunt, I. Johnson, M. G. Chasanov, H. M. Feder

The solubilities of the transition metals from scundium to nickel, inclusive, in liquid cadmium were determined by sampling saturated solutions. At 400°C these solubilities (ppm) are:Sc, Co, 22; Ni, 12000. Relative partial molal enthalpies and excess partial molal entropies at infinite dilution for the solutes Cr, Mn, Fe, and Co are compared zoitlz similar data for the post-transition metals. Three new intermetallic phases, ScCd,, TiCd, and Ti,Cd, encozaztered in the course of this work, are reported. Measurements of the solubility of the 3-d transition metals in liquid cadmium have been reported' only for iron. The present measurements for the entire series were made as an aid to the study of the systematics of alloy formation. EXPERIMENTAL The apparatus and sampling techniques used for the solubility determinations were similar to those described by Martin etal.' Temperatures were measured with a Pt/Pt-10 pct Rh thermocouple sheathed in recrystallized alumina and immersed in the solution. The thermocouple was recalibrated periodically during the course of the investigation. Thermocouple voltages were measured to the neares 0.01 mv with a Rubicon model 2732 potentiometer. A scaled-down version of the apparratus, in which the total metal charge was about 90 g, was employed to measure the solubility of scandium. Two-mm ID Vycor filter pipets were used to sample the scandium-cadmiurn solutions; the samples weighed about 2g- Cadmium with a minimum purity of 99.95 pct was used; the only impurities detected spectrochem-ically were C'u and Mg, both less than 10 ppm. The purities of the other metals were: scandium, 99.9 pct; titanium. 99.92 pct; vanadium, 99.9 pct; chromium, 99).99 pct; manganese, 99.9+ pct; iron, 99.90 pct; cobalt, 99.95 pct; and nickel, 99.96 pct. Solidified melts were routinely analyzed spectro-graphically. No significant contamination by the crucible, sampling pipets, or other materials of construction was observed. The entire specimen obtained by sampling was dissolved to preclude analytical errors due to segregation on cooling. Colorimetric methods3 were used for the analyses of cobalt (2-nitroso-l-naphthol), manganese (permanganate), nickel (dimethylglyoxime), titanium (peroxide), and vanadium (thiocyanate).4 Chromium, iron, and scandium were neutron-irradiated to produce The dissolved samples were gamma-counted to determine solute concentration.For the separation of intermediate phases from cadmium-rich alloys selective leaching by saturated ammonium nitrate solutions was employed. The concentration of cadmium in the successive leaches was followed polarographically and the process was terminated when the rate of cadmium dissolution decreased markedly. For the further investigation of intermediate phases 1/4- in. diam powder compacts were pressed at 80,000 psi and annealed in argon at 315" to 330°C for 10 days. Larger quantities of alloys were prepared in sealed tantalum capsules heated in a rocking furnace.

Jan 1, 1962

By Dwight K. Smith

A new pozzolanic composition has been developed for cementing oil wells where moderate to high temperatures prevail. This material is an entirely different concept to other oil well cementing materials, such as portland cements, cements containing additives, or liquid resins. Its characteristics are such that it is not, at present, recommended for use at temperatures less than 140º F. It can he either accelerated or retarded across a wide range of well conditions. This new cement is composed of a pozzolanic material, hydrated lime, and a chemical activator to give it early initial strength. This material can be used in wells from 6,000 to 18,000 or more feet where temperature conditions are similar to those along the Gulf Coast. This cement, when set, has no soluble portion subject to leaching or any compounds that should be attacked by sulfate waters or brines. For this reason, it should be permanent when placed adjacent to formations carrying any type of fluid. The compressive strengths in 24 hours are more than adequate for wells where temperatures are 140°F and higher. These values ore in excess of many other types of cementing composition presently in use in the field. This pozzolanic composition does not retrogress in strength at high temperatures as do some other types of cementing materials. The slurry weights of this material will vary slightly according to the specific gravity and water requirements of the pozzolnn itself. The materials covered herein will mix from 13.5 to 14.3 lb/gal, and will have a waiting-on-cement time comparable to other materials used under the same conditions. Economically speaking, this composition is less expensive than either portland cements or retarded cements presently being used under deep well conditions. INTRODUCTION Pozzolans are siliceous material which, though not cementitious in themselves, contain constituents which at ordinary temperatures will combine with lime in the presence of water to form compounds which have a low solubility and possess cementing properties. The use of pozzolanic materials dates back many hundreds of years and both the ancient Greeks and Romans were aware that certain volcanic deposits, if finely ground and mixed with lime and sand, yielded a mortar which possessed special properties. Generally, the early strengths of such materials were rather weak and were considered insufficient for modern commercial usages. Pozzolanic materials have been used extensively with portland cement in mass concrete to obtain special properties. In recent years, large quantities of certain pozzolanic materials have been used successfully admixed into portland cements for oil well cementing. Pozzolans, being reactive silicates, will combine with the free lime that is an inherent component of set portland cements and thereby. becomes cementitious themselves. POZZOLANS FOR OIL WELL CEMENTING There are many types of pozzolans, some of which are more reactive than others. The quality of the pozzoIan depends on the degree of reactivity, chemical composition, fineness, and other less well understood factors. Some of the more widely accepted pozzolans are those classified as fly ashes, while others are certain materials of volcanic origin. pozzolans which require large vol-

Jan 1, 1957

By Simon D. Strauss

INTRODUCTION The changes in ownership, management, and operation of the non-fuel minerals industry since the Second World War have been dramatic. World-leading enterprises have lost their identity; host countries have taken over operations from multi-national firms; marketing practices have been drastically altered - and yet the world industry is supplying minerals on a scale far greater than had been anticipated in projections made at mid-century. The world's known mineral resources have been enormously expanded, despite the doom sayers who for decades have been predicting that depletion of non-renewable resources would impose limits to growth. PALEY REPORT One can set the stage by reviewing how the minerals outlook was regarded in a thoughtful and comprehensive analysis made in the years 1950 and 1951. During the War years, President Harry Truman of the United States had come to appreciate the decisive role played by minerals resources through his chairmanship as a U.S Senator of a committee that investigated the procurement and allocation of natural resources. In 1950, in the Cold War era that resulted in actual military conflict in Korea, he appointed a prestigious five-man commission to study the problems of Materials Policy over the following quarter century. Their findings, published in five impressive volumes in early 1952, became known as the Paley report. The text was prepared by expert scientists and economists who spent 18 months assembling statistics, making projections of future demand, and interviewing leaders in industry, academia, and government. [ ] The Commission had correctly foreseen that aluminum would replace copper as the largest volume non-ferrous metal, but it had fallen short of reality by a wide margin indeed for all three materials. Even though the Commission's expectations for growth proved to be extremely understated, it had concluded its report with grave foreboding about the effect of its estimates of demand in relation to supply, as follows: "Consumption of almost all materials is expanding at compound rates and is thus pressing harder and harder against resources which, whatever else they may be doing, are not similarly expanding. This materials problem is thus not the kind of 'shortage' problem, local and transient, which in the past has found its solution in price changes which have brought supply and demand back into balance. The terms of the materials problem we face today are larger and more pervasive." With respect to some minerals, the Paley Report expressed scepticism that, in fact, supplies would be forthcoming regardless of price. Because the Paley demand forecasts understated the actual growth in demand for virtually every mineral, one could logically have expected frequent and protracted shortages in the years since 1950.

Jan 1, 1985