Search Documents

By W. M. Robertson

The formation of grain boundary grooves on surfaces of poly crystalline samples of cobalt and iron immersed in liquid lead has been studied. The grooves form by volume diffusion of the solutes cobalt and iron in the liquid. The diffusion coefficients of the solutes in liquid lead are derived from the measured rate of grooving. The diffusion coefficients are described by the relation D = Do exp (-Q/RT), with, for cobalt, Do = 4.6 x 10-4 sq cm per sec and Q = 5300 ± 800 cal per mole, and for iron, DO = 4.9 x 10-3 sq cm per sec and Q = 10,500 ± 1500 cal per mole. LIQUID metal-solid metal interactions occur at solid-liquid interfaces. Interfacial energy provides a driving force to change the morphology of the interface. Mullins1,2 has derived expressions for the kinetics of interface morphology changes driven by capillarity. These expressions can be applied to an isothermal system of a solid in equilibrium with a liquid saturated with the solid. Surface profile changes can occur by volume diffusion of the solute in the liquid, by volume self-diffusion in the solid, and by interfacial diffusion at the liquid-solid interface. A groove will form at the intersection of a grain boundary with a solid-liquid interface, reducing the total interfacial free energy of the system. The solid-liquid interfacial energy ? must be greater than half the grain boundary energy of the solid ?6 for Mullins' calculations to apply. If ? is less than ?b/2, then the liquid penetrates the boundaries, separating the grains rather than forming grooves. Boundary penetration did not occur in the work described here. where CO is the equilibrium volume concentration of the solid in the liquid, Dv the volume diffusion coefficient of the solid in the liquid, ? the interfacial free energy of the solid-liquid interface, O the atomic volume of the solid crystal, k Boltzmann's constant and T the absolute temperature. Eqs. [1] and [2 ] also apply to grooving by volume self-diffusion in the solid,1 with CoODv = D Self, where DSelf is the volume self-diffusion coefficient of the solid. For a grooving mechanism of interfacial diffusion at the solid-liquid interface, the groove width is given by2 where CS is the interfacial concentration of the diffusing species, and DS is the interfacial diffusion coefficient. Eqs. [1] and [3] can be used to determine the mechanism of groove growth. A t1/3 dependence of the growth indicates volume diffusion and t1/4 indicates interfacial diffusion. In some cases, volume diffusion and interfacial diffusion both can contribute substantially to the grooving process, causing the time dependence to be intermediate between t 1/3 and t1/4.3 For these cases, the relative contributions of the two processes can be separated.4 However, in many cases, one process will be dominant, and the data can be analyzed on the basis of Eq. [1] or Eq. [3] alone. The time dependences for volume diffusion in a liquid and volume self-diffusion in a solid are the same. However, the self-diffusion contribution of the solid is usually negligible compared to volume diffusion in the liquid. After the grooving mechanism has been determined, Eq. [1] or Eq. [3 ] yields the kinetic parameter A or B. The kinetic parameter can be used to calculate values for the unknown quantities in the product CD?. Usually C is known or can be estimated. If ? is known, then D can be calculated. In a measurement of grain boundary grooving of copper in liquid lead,' the time dependence indicated volume diffusion in the liquid. The quantities Co, Dv, and ? were obtained from the literature, giving excellent agreement between the observed values of A and the values calculated from Eq. [2 ].5 In a study of the grooving of several refractory metals in liquid tin and liquid silver, A1len6 educed that grooves formed by volume diffusion in the liquid. In a study of nickel in a nickel sulfide melt, Steidel, Li, and spencer7 found volume diffusion grooving kinetics. Both Dv and ? were unknown, so they could not obtain either one separately, though they did obtain a reasonable value for the temperature dependence of the product Dv ?. Several methods have been used to obtain surface profiles. It can be done by sectioning through the interface7 or by chemically removing the liquid from the solid surface after solidification of the liquid.6 However, if the liquid dewets the solid on removing the solid from the melt, then the interface can be observed directly. This method was used previously' and was utilized also in the present study. EXPERIMENTAL PROCEDURE Lead of 99.999 pct purity was obtained from American Smelting and Refining Co. Cobalt sheet was obtained from Sherritt-Gordon Mines, Ltd., with a nominal purity of 99.9 pct, the principal impurities being nickel, iron, copper, carbon, and sulfur. The sheet was

Jan 1, 1969

By T. S. Fuller

MUCH study has been given by engineers in general, and investigators in particular, to the concentration of stress which occurs under load in structural members having irregularities in section such as notches, shoulders, key ways, tool marks, etc. The result of the effect of both fresh and salt water corrosion upon the endurance properties of various metals and alloys has been ably determined and the general laws underlying these phenomena carefully pointed out by McAdam. From a practical standpoint, 'however, it is after all the endurance value of corroded, non-symmetrical sections which is most pertinent. In the experiments about to be described rotating cantilever specimens of nickel steel of the 3.5 per cent nickel ' 0.35 per cent carbon type have been used. These were machined from bars l 1/8. in. dia. and 9% in. long and were heat-treated by quenching in oil from 825 deg. C. followed by reheating to 650' C. and oil quenching. The tensile and impact properties of this material so heat- treated follow:

Jan 1, 1931

By M. D. Cooper

UNDERGRADUATES in mining engineering may be prepared for work by giving them sound instruction in the courses generally considered essential to the profession. The industry is not deeply concerned about the details of those courses. The average man in the coal industry does not wish to insist upon a rigid program. Therefore, he differs little from those in the teaching profession who evidently are not unanimous in their opinions, or all college catalogs would be alike. For the good of the profession, it is just as well that there should be differences in regard to details. It appears that students graduating in mining engineering from the accredited institutions receive similar instruction. It is taken for granted that the graduate will have a good understanding of English, mathematics, mechanics, electricity, chemistry, physics, geology, and surveying, in addition to his major courses in mining. Somewhat belatedly, industry hopes he will have had at least an introduction to the subject of labor relations, the importance of which is only too clear at present. The coal industry expects, of course, that students in mining engineering will be taught the strictly mining subjects by men who have had practical experience in the mines and who keep themselves well informed in regard to current methods. While the undergraduate is subject to the control of members of the teaching profession, industry expects him to be trained in certain ways that are not a part of his textbooks, but can be made an inseparable part of his development by the skillful supervision of his teachers. Of the desired characteristics, dependability is of the utmost importance. Probably most employers would overlook certain short-comings if the young graduate demonstrated that he was thoroughly dependable. If he always appeared at the right place at the right time with the proper equipment, he would soon be well established as a welcome member of his organization. The graduate who gets a reputation for being undependable will have little opportunity for advancement. Closely allied to dependability is loyalty. Athletic teams and social groups in college tend to develop loyalty which may well be carried over into industry. This does not mean that the graduate has to be satisfied with customary practices. The average manager is glad to see the graduate make constructive criticism as long as he demonstrates his loyalty at the same time. It is important that his loyalty keeps him alert arid ready to take helpful action for the benefit of his organization, and especially to stand with it during times of stress. With or without an introduction to labor relations in college, the graduate is expected to develop ability in this most important field. Beginning with himself, he will find it essential to deal agreeably with his immediate associates. Getting along in friendly fashion with his own small group will be a great help as his responsibilities increase and he is required to deal with larger numbers of persons. On a higher scale, his interest in his community may grow at the same time by voluntary work in any one of a great number of useful activities. Industry expects the graduate engineer to be a mature man at the time he gets his first job. Supposing that he has better than average intelligence, industry expects him to continue to grow intellectually and to fit himself for responsible jobs when they are offered to him. For this reason, employers are apt to look over his college record to see what he did that would indicate his fitness for leadership. There is interest in knowing what he did beyond the requirements. As evidence of his mental growth, it is expected that the graduate will do independent thinking; that he will not take too much for granted. When he reads a report, he should develop the ability to see whether the subject is new or whether it is just a description of an old method that has been superseded by something better. For the same reason, the graduate should be able to accept conditions that have been arrived at by sound experience rather than cling to something else that seems better in theory. In this connection, it may be remarked that the ability to operate successfully a personal budget will be noteworthy, as it may be assumed that a man who knows how to conduct his own affairs will be prepared to assume the larger responsibilities of industry. Membership in AIME will indicate to the employer that the graduate is interested in the mining industry as a whole. Therefore, it is good evidence of something more than a local outlook. Quite apart from college training and mental ability, the newly employed graduate will be expected to be willing to do hard manual labor for a time. This will give him an understanding of the actual conditions of work done by those he supervises later. He will gain their confidence and be able to see that the work is carried on in a safe and efficient manner. Part of this experience may be acquired in his summer vacations during his undergraduate career. Such work would make a favorable impression on a prospective employer, especially if the graduate showed a willingness to continue it until he was prepared for something better. To summarize, the man in authority in the coal industry will not quarrel with the professor of mining engineering over details of curriculum. He will be pleased if the school sends him graduates who possess a good foundation in the courses studied, and who may be depended upon to do their work faithfully and intelligently. Such men will be ready when the time comes to assume their places as leaders of an essential industry.

Jan 1, 1951

By W. E. Bergman, P. G. Carpenter, H. B. Fisher

The conditions under which barium carbonate can be used to remove sulfates from drilling muds are limited The amount of sulfate remaining in solution in the system after treatment with barium carbonate is shown to be a function of the concentration of the carbonate and barium ions and the concentration of other electrolytes. Barium hydroxide may advantageously replace barium carbonate when the contamination is not entirely due to anhydrite (calcium in the system is then stoichiometrically less than sulfate) or when the carbonate concentration is high. The effect of substances such as quebracho, phosphates, and chromates, which form complexes or precipitates with barium, is discussed. INTRODUCTION As the complexity of the operations in drilling for oil has increased, more attention has of necessity been directed to the problems pertaining to the maintenance of good drilling mud properties. As a result, chemical treatment of muds has become an important factor in recent years. Some of these treatments have been designed to eliminate the deleterious effects of contaminants in aqueous mud systems by precipitation or other means. The most common of substances encountered during drilling include sodium chloride, cement, and calcium sulfate while various other contaminants: usually in small amounts, may be introduced from the water, clays, and other materials used in preparation of the mud. In certain cases, for example where continued salt-water flow is encountered or massive anhydrite is drilled, special muds may be used so that the physical properties of the mud will remain satisfactory for drilling. In other cases, it is desirable to remove the contaminants so that soluble electrolytes in the system are maintained at low values. For sulfate contamination, the conlmon practice in the field is to add barium carbonate to precipitate the sulfate as barium sulfate Ordinarily such a procedure gives satisfactory results. There have been important instances, however, where addition of barium carbonate was not effective in removal of soluble sulfates from drilling muds. and it is to these cases that the present paper is directed. While it is generally known that barium carbonate is not always effective in removing soluble sulfates from drilling muds, certain inconsistencies appear in the literature as to the limitations of its use, and little explanation for the limitations are given. Varnell and Kimbrel state that "the treatment (with barium carbonate for removal of sulfate) is simple and consists in maintaining a pH of 9 with caustic soda and quebracho." They caution that concentrations of quebracho greater than 1 lb./bbl. may inhibit the reaction. In another publication', a pH of 10.5 is considered "the maximum desirable," and the indication is that as much as 2.5 lb. quebracho per barrel may be present in the particular mud under discussion. Lancaster and Mitchell5 state that appreciable amounts of phosphates in the mud will inhibit the reaction with barium carbonate and that the phosphate treatment should be discontinued at least 24 hours before addition of the carbonate. Experimental work was initiated to ascertain the factors involved in using barium carbonate for the removal of sulfate contamination in drilling muds. While the experimental data herein reported are limited, they focus attention on the pertinent factors which must be considered for successful treatment. These factors are discussed from a practical and a theoretical view, the latter being supported by equilibrium data found in the literature. Further, it will be appreciated that the factors involved in this specific study will be closely analogous to those in certain of the other chemical treatments which involve a precipitation of the soluble contaminant. A thorough comprehension of these factors should result in a more fruitful application of this type of chemical reaction to the treatment of drilling muds. EXPERIMENTAL A. Reagents Two muds were used during this investigation. For one series of tests, bentonite suspensions were prepared by dilution of a stock suspension containing 8 per cent by weight of bentonite (Aquagel). For another series, a 6.4 per cent ben-tonitic mud weighted to 9.7 lb./gal. with barium sulfate (Mag-cobar) was used. Distilled water was used in all preparations. The quebracho (72% tannin extract) was obtained from the Thompson-Hayward Co. of Tulsa and contained 11.4 per cent moisture (105 C.). All other materials were reagent grade, and concentrations were corrected for water of crystallization, if any. All concentrations are expressed in pounds per barrel (42 gallons). B. Technique The systems — either mud or water — were contaminated with either sodium or calcium sulfate after treatment with the desired amounts of sodium hydroxide and quebracbo. For treatments with barium carbonate an approximately 3-fold excess (5 lb./bbl.) was used over that computed to be required to precipitate all the sulfate as barium sulfate. Barium hydroxide was used in concentrations of 2 lb./bbl. — about

Jan 1, 1949

By M. D. Cooper

UNDERGRADUATES in mining engineering may be prepared for work by giving them sound instruction in the courses generally considered essential to the profession. The industry is not deeply concerned about the details of those courses. The average man in the coal industry does not wish to insist upon a rigid program. Therefore, he differs little from those in the teaching profession who evidently are not unanimous in their opinions, or all college catalogs would be alike. For the good of the profession, it is just as well that there should be differences in regard to details. It appears that students graduating in mining engineering from the accredited institutions receive similar instruction. It is taken for granted that the graduate will have a good understanding of English, mathematics, mechanics, electricity, chemistry, physics, geology, and surveying, in addition to his major courses in mining. Somewhat belatedly, industry hopes he will have had at least an introduction to the subject of labor relations, the importance of which is only too clear at present. The coal industry expects, of course, that students in mining engineering will be taught the strictly mining subjects by men who have had practical experience in the mines and who keep themselves well informed in regard to current methods. While the undergraduate is subject to the control of members of the teaching profession, industry expects him to be trained in certain ways that are not a part of his textbooks, but can be made an inseparable part of his development by the skillful supervision of his teachers. Of the desired characteristics, dependability is of the utmost importance. Probably most employers would overlook certain short-comings if the young graduate demonstrated that he was thoroughly dependable. If he always appeared at the right place at the right time with the proper equipment, he would soon be well established as a welcome member of his organization. The graduate who gets a reputation for being undependable will have little opportunity for advancement. Closely allied to dependability is loyalty. Athletic teams and social groups in college tend to develop loyalty which may well be carried over into industry. This does not mean that the graduate has to be satisfied with customary practices. The average manager is glad to see the graduate make constructive criticism as long as he demonstrates his loyalty at the same time. It is important that his loyalty keeps him alert arid ready to take helpful action for the benefit of his organization, and especially to stand with it during times of stress. With or without an introduction to labor relations in college, the graduate is expected to develop ability in this most important field. Beginning with himself, he will find it essential to deal agreeably with his immediate associates. Getting along in friendly fashion with his own small group will be a great help as his responsibilities increase and he is required to deal with larger numbers of persons. On a higher scale, his interest in his community may grow at the same time by voluntary work in any one of a great number of useful activities. Industry expects the graduate engineer to be a mature man at the time he gets his first job. Supposing that he has better than average intelligence, industry expects him to continue to grow intellectually and to fit himself for responsible jobs when they are offered to him. For this reason, employers are apt to look over his college record to see what he did that would indicate his fitness for leadership. There is interest in knowing what he did beyond the requirements. As evidence of his mental growth, it is expected that the graduate will do independent thinking; that he will not take too much for granted. When he reads a report, he should develop the ability to see whether the subject is new or whether it is just a description of an old method that has been superseded by something better. For the same reason, the graduate should be able to accept conditions that have been arrived at by sound experience rather than cling to something else that seems better in theory. In this connection, it may be remarked that the ability to operate successfully a personal budget will be noteworthy, as it may be assumed that a man who knows how to conduct his own affairs will be prepared to assume the larger responsibilities of industry. Membership in AIME will indicate to the employer that the graduate is interested in the mining industry as a whole. Therefore, it is good evidence of something more than a local outlook. Quite apart from college training and mental ability, the newly employed graduate will be expected to be willing to do hard manual labor for a time. This will give him an understanding of the actual conditions of work done by those he supervises later. He will gain their confidence and be able to see that the work is carried on in a safe and efficient manner. Part of this experience may be acquired in his summer vacations during his undergraduate career. Such work would make a favorable impression on a prospective employer, especially if the graduate showed a willingness to continue it until he was prepared for something better. To summarize, the man in authority in the coal industry will not quarrel with the professor of mining engineering over details of curriculum. He will be pleased if the school sends him graduates who possess a good foundation in the courses studied, and who may be depended upon to do their work faithfully and intelligently. Such men will be ready when the time comes to assume their places as leaders of an essential industry.

Jan 1, 1951

By P. G. Carpenter, H. B. Fisher, W. E. Bergman

The conditions under which barium carbonate can be used to remove sulfates from drilling muds are limited The amount of sulfate remaining in solution in the system after treatment with barium carbonate is shown to be a function of the concentration of the carbonate and barium ions and the concentration of other electrolytes. Barium hydroxide may advantageously replace barium carbonate when the contamination is not entirely due to anhydrite (calcium in the system is then stoichiometrically less than sulfate) or when the carbonate concentration is high. The effect of substances such as quebracho, phosphates, and chromates, which form complexes or precipitates with barium, is discussed. INTRODUCTION As the complexity of the operations in drilling for oil has increased, more attention has of necessity been directed to the problems pertaining to the maintenance of good drilling mud properties. As a result, chemical treatment of muds has become an important factor in recent years. Some of these treatments have been designed to eliminate the deleterious effects of contaminants in aqueous mud systems by precipitation or other means. The most common of substances encountered during drilling include sodium chloride, cement, and calcium sulfate while various other contaminants: usually in small amounts, may be introduced from the water, clays, and other materials used in preparation of the mud. In certain cases, for example where continued salt-water flow is encountered or massive anhydrite is drilled, special muds may be used so that the physical properties of the mud will remain satisfactory for drilling. In other cases, it is desirable to remove the contaminants so that soluble electrolytes in the system are maintained at low values. For sulfate contamination, the conlmon practice in the field is to add barium carbonate to precipitate the sulfate as barium sulfate Ordinarily such a procedure gives satisfactory results. There have been important instances, however, where addition of barium carbonate was not effective in removal of soluble sulfates from drilling muds. and it is to these cases that the present paper is directed. While it is generally known that barium carbonate is not always effective in removing soluble sulfates from drilling muds, certain inconsistencies appear in the literature as to the limitations of its use, and little explanation for the limitations are given. Varnell and Kimbrel state that "the treatment (with barium carbonate for removal of sulfate) is simple and consists in maintaining a pH of 9 with caustic soda and quebracho." They caution that concentrations of quebracho greater than 1 lb./bbl. may inhibit the reaction. In another publication', a pH of 10.5 is considered "the maximum desirable," and the indication is that as much as 2.5 lb. quebracho per barrel may be present in the particular mud under discussion. Lancaster and Mitchell5 state that appreciable amounts of phosphates in the mud will inhibit the reaction with barium carbonate and that the phosphate treatment should be discontinued at least 24 hours before addition of the carbonate. Experimental work was initiated to ascertain the factors involved in using barium carbonate for the removal of sulfate contamination in drilling muds. While the experimental data herein reported are limited, they focus attention on the pertinent factors which must be considered for successful treatment. These factors are discussed from a practical and a theoretical view, the latter being supported by equilibrium data found in the literature. Further, it will be appreciated that the factors involved in this specific study will be closely analogous to those in certain of the other chemical treatments which involve a precipitation of the soluble contaminant. A thorough comprehension of these factors should result in a more fruitful application of this type of chemical reaction to the treatment of drilling muds. EXPERIMENTAL A. Reagents Two muds were used during this investigation. For one series of tests, bentonite suspensions were prepared by dilution of a stock suspension containing 8 per cent by weight of bentonite (Aquagel). For another series, a 6.4 per cent ben-tonitic mud weighted to 9.7 lb./gal. with barium sulfate (Mag-cobar) was used. Distilled water was used in all preparations. The quebracho (72% tannin extract) was obtained from the Thompson-Hayward Co. of Tulsa and contained 11.4 per cent moisture (105 C.). All other materials were reagent grade, and concentrations were corrected for water of crystallization, if any. All concentrations are expressed in pounds per barrel (42 gallons). B. Technique The systems — either mud or water — were contaminated with either sodium or calcium sulfate after treatment with the desired amounts of sodium hydroxide and quebracbo. For treatments with barium carbonate an approximately 3-fold excess (5 lb./bbl.) was used over that computed to be required to precipitate all the sulfate as barium sulfate. Barium hydroxide was used in concentrations of 2 lb./bbl. — about

Jan 1, 1949

By David Moskowitz, Ira Binder, Robert Steinitz

THE hard refractory borides of the transition elements of the 4th, 5th, and 6th groups of the Periodic System have been the subject of a number of recent investigations.'-' It is well known now that most of these elements form several different borides, and Kiessling8 has summarized the rules which govern to some extent the arrangements of the boron atoms in the various structures. Melting points of a few borides have been published." The systems Fe-B, Ni-B, and Co-B have been reported," but, as these borides are rather low melting, they are outside of the groups of boron compounds considered here. Brewer' has tested the stability of various borides and estimated a number of eutectic temperatures between different borides, but in no case was the complete system of a transition metal and boron investigated. The phase diagram becomes of special importance if the preparation of the borides from the elements in powdered form is considered; the lowest eutectic temperature will determine the first appearance of a liquid phase. Also, the knowledge of high temperature phases, if they exist, is important for the preparation of bodies from these borides by hot pressing or sintering. During the investigation of various metal borides,7 it was found that there were more boride phases existing in the Mo-B system than reported by Kiessling." They occur, however, only at temperatures above 1500°C and were, therefore, not found by him. This led to a study of the equilibrium diagram of the Mo-B system. ranging from 0 to 25 pct B and from room temperature to the liquidus. Part of this investigation was reported during the "Research in Progress" session at the 1952 Annual Meeting of the AIME.11 Raw Materials and Preparation of the Borides The raw materials used were commercial molybdenum and boron powder, both supplied by the Molybdenum Corp. of America. The molybdenum powder was 99+ pct pure? while the boron powder contained about 83 to 85 pct B. A large percentage of the impurities in this powder was oxygen, with the rest formed by iron, calcium, and unknown substances. The low purity of the boron used was, however, not considered detrimental to the final product, as most of the impurities evaporated at the high temperatures at which the borides were formed. The final product always had a minimum purity of 96 to 98 pct (figured as molybdenum and boron), with carbon, iron, and probably oxygen being the remaining products. Carbon is usually present as graphite. The chemical analyses always confirmed the compositions which corresponded to the crystallographic structures as determined by X-ray diffraction, and the boron content of the finished product agreed closely with that of the starting mixture; no boron was lost during the boride preparation. The chemical analysis methods employed for molybdenum and boron were previously described by Blumenthal.12,13 The powders were mixed by hand in the desired proportions, compressed at room temperature under low pressure, and then heated under hydrogen to about 1500" to 1700°C in a graphite crucible to form the borides. Usually, the three well-known borides Mo,B, MOB, and Mo,B,, which are stable at room temperatures, were prepared in this way, and all other compositions were made by mixing these borides in various ratios or by the addition of molybdenum or boron powders for the very low or very high boron contents. Preparation of two-phase compositions directly from the elemental powders was tried only occasionally to check whether equilibrium could be reached in this way. Experimental Procedures The stable borides were mixed in the desired ratios and heated under hydrogen in graphite crucibles to various temperatures. The well insulated crucibles were heated in a high frequency induction furnace. Special care was taken to obtain exact temperature measurement, which proved much more difficult than originally anticipated. It is believed that individual temperature measurements have an error of less than ±25ºC, while melting or transformation temperatures are accurate within ±50°C. The temperatures were measured with an optical pyrometer which was aimed at the closed end of a graphite tube extending down into the crucible. close to the samples. Attempts to measure directly through the hydrogen exit stack failed. The crucible arrangement is shown in Fig. 1. Heating was done at a slow rate to be sure that the temperature inside the crucible was uniform. The specimens were kept at the final temperature for about 30 min. For the investigation of high temperature phases, some samples were quenched. They were heated, without atmosphere protection, in a very small graphite crucible which could be rapidly removed from the high frequency coil, and dropped into water. These quenched samples were afterwards annealed to establish the equilibrium at lower temperatures. The melting points or the positions of the solidus and liquidus lines were determined by heating the specimens to various temperatures and examining them at room temperature for evidence of a liquid phase. These results were checked later on by thermal arrest curves, especially to determine the exact position of the eutectic temperature line. For this purpose about 200 g of the boride were melted in a graphite crucible, in an arrangement similar to Fig. 1. Slow cooling was assured by very good

Jan 1, 1953

By F. B. Sherman, Keros Cartwright

Sanitary land filling has become one of the most widely used methods of disposing of solid refuse. A principal concern of regulatory agencies and the public itself is that landfill operations do not degrade the physical environment, including water resources, and the ground-water reservoir in particular. Knowledge of ground-water and engineering geology can guide landfill operations into suitable terranes or develop measures to compensate for natural limitations at a particular site. Experience and research in Illinois suggest four activities relating to landfill disposal that warrant attention by geologists and engineers: (1) regional delineation of favorable and unfavorable hydrogeologic conditions to facilitate planning and preliminary screening of potential landfill sites; (2) site evaluations, with considerations of geologic materials, topography, water levels, flow systems, and local occurrence and use of water resources; (3) research on aspects of the hydrogeologic environment that control effects of, or are modified by, landfills; and (4) formulation of practices in the siting, construction, and operation of landfills that prevent, mitigate, or isolate deleterious effects. The first two activities are basically in the domain of earth science, requiring the application of fundamental concepts of geology and hydrology and conventional site-exploration methods. The third activity, research, requires contributions from geology as well as other disciplines, including soil physics, sanitary engineering, and chemistry. The fourth calls for policy decisions by regulatory agencies and elected officials, using the contributions of scientists and engineers. Throughout history, man has disposed of unwanted materials by dumping. As urbanization has increased, haphazard dumping practices have given way to disposal under more controlled conditions because of increasing congestion of population and production of waste and greater concern for public health and environmental amenities. Many states and communities have already outlawed open dumping and open burning of refuse. The only practical methods of disposal of large volumes of refuse, therefore, are contained, high-temperature incineration, or burial in a sanitary landfill. In Illinois, regulation of solid waste disposal has been delegated to the Environmental Protection Agency. Each session of the legislature since 1965 has passed increasingly strict laws regulating waste diposal. As a result, the work of evaluating sanitary landfill sites has increased significantly for both the Department of Public Health, now the Environmental Protection Agency, and the Illinois State Geological Survey, which advises the Agency on matters of ground-water geology and pollution. In fact, our ground-water staff spends as much time on studies relating to waste disposal, primarily sanitary landfills, as on ground-water resource studies. Many other geological agencies are experiencing similar demands for increased assistance in solving waste-disposal problems. This paper summarizes some of the salient features of the sanitary landfill concept, describes activities of the Illinois Geological Survey in ground-water and engineering geology relating to landfills, and suggests policies that need consideration. A sanitary landfill is located and operated in such a way that vermin and pests, nuisances, and degradation of air and water are kept at acceptable levels. Some of the physical requirements of a sanitary landfill are all-weather roads for year-round access, fences to retain blowing paper, a daily cover of at least six inches of suitable earth material, and a final cover of at least 2 ft of earth material. Dumping into or adjacent to standing water generally is not allowed. Two common operating techniques are used. In the first, trenches are dug, the refuse is placed in them, and the earth removed from the trenches is used to cover the waste. In the second method, area fill, refuse is placed in low ground and covered with earth from adjacent high areas. The hydrology of the site is a prime consideration in locating sanitary landfills. Putrescible refuse, if saturated above field capacity, produces a leachate that usually has a high concentration of dissolved solids.2 As the leachate also acts as an agent for transporting bacterial pollutants, it constitutes a potential pollution hazard. To reduce the production of leachates, the topography of the landfill area should be such that surface water will not flow into or through the fill. Operations that will result in refuse disposal below or near the highest known water-table elevation may be required to take corrective or preventive measures to protect the ground water. In practice, under humid conditions such as prevail in Illinois, locations where disposal can take place above the water table are relatively few because surficial materials are commonly fine-grained, which permits slow gravity drainage and results in high degrees of saturation (100% moisture content) near the surface. At some sites, although disposal has taken place above the water table, ground-water mounds have developed, resulting in permanent saturation of the refuse. Permeability barriers usually are required to protect the ground-water reservoir from degradation by leachates. The convention in Illinois is to have a minimum of

Jan 1, 1972

By R. E. Smallman

R. E. Smallman (University of Birmingham, England)—Recently, Tedmon and Ferriss11 have determined the yield stress parameters oi and ky for tantalum by measuring the lower yield stress as a function of grain size 2d and fitting the results to a relationship of the form They report that although ky , which is taken to be a measure of the dislocation locking strength, is small (- 2 to 4 x 106 cgs units) a substantial yield drop is nevertheless observed in a normal tensile test. Niobium gives a similar result,12-14 as pointed out in the original work by Adams et a1.,12 and in order to check this apparent anomaly the yield-stress parameters of electron beam-melted niobium have recently been reanalyzed15 by the Luders strain technique. In this method the strain hardening part of the stress-strain curve is extrapolated to zero plastic strain; the intercept on the preyield portion of the curve is taken to give oi, whilst the difference between oi and the lower yield stress gives kyd-1/2. The results indicate that ky increases with increasing grain size and hence, a plot of vs d-112 yields an apparent ky, which is lower than the true value. A similar effect could account for the small ky found in the relatively pure tantalum used by Tedmon and Ferriss. The variation of ky with grain size shows that dislocations are more strongly locked in coarse-grained specimens than in fine-grained samples. In niobium, this may be attributed to the fact that the dislocation density in the fine-grained material is higher than that found in the coarse-grained samples which are given a sufficiently prolonged anneal to remove any residual substructure and, since the metal contains only a small amount of interstitual impurity, a variation in locking occurs. By contrast, application of both the grain size analysis and the Luders strain method to yield-stress data from commercially pure vanadium containing a large amount of interstitial impurity gives consistent values of oi and ky, with ky independent of grain size and temperature. Electron microscope observations show minor variations in dislocation density from grain size to grain size, but in any case in this material the dislocations are heavily locked with precipitate. On yielding new dislocations are generated and, as a consequence, the importance of any differences in dislocation density between the various specimens of different grain size is considerably reduced. It is perhaps significant that Adams and lannucci,16 working with a grade of tantalum containing a higher interstitial content than that used by Tedmon and Ferriss, prepared the specimens of different grain size by annealing in the temperature range 1500" to 2000° C to minimize any differences in dislocation structure, and found that ky had a value of 1.04 x 107 cgs units, independent of testing temperature. Such behavior is consistent with the dislocations being locked by carbide precipitates so that the generation of free dislocations is an athermal process. The recent work of Gilbert et al.17 also shows that in tantalum there is no significant variation of ky with grain size provided it contains 150 ppm of oxygen. In this case, however, the dislocations are not locked by precipitate and ky is temperature dependent. C. S. Tedmon and D. P. Ferriss (authors' reply)— We would like to thank Dr. Smallman for his interesting comments and discussion to our paper, "The Dependence of Yield Stress on Grain Size for Tantalum and a 10 pct W-90 pct Ta Alloy".18 It was suggested that perhaps the relatively small values obtained by us for ky of tantalum could be attributed to the same cause that accounts for the apparently small values of ky that result when it is determined by the Luders Strain technique. Since our values were obtained by plotting the lower yield stress vs the reciprocal of the square root of the grain size, it is not clear how this could be the case. The values of ky in this experiment have been calculated, using the Luders strain technique. With this method, values for ky on the order of 2 x 105 to 5 x lo6 cgs units were obtained. In spite of this rather large variation, the magnitudes are still small, and there appeared to be no good correlation between ky and the grain size or the yield stress, probably because of the difficulty in accurately extrapolating the work-hardening portion of the curve back to zero plastic strain. As was shown in the original data,18 there was little work hardening in any of the curves, at any temperature. In his discussion, Dr. Smallman also points out how ky has been observed to increase with increasing grain size, when determined by the Luders strain technique. There are at least two possible explanations for this. In the first case, if it is assumed that the bulk of the interstitial impurities are concentrated at the grain boundaries, then, of course, the available grain boundary area would decrease with increasing grain size, thus presenting less area for the interstitials, which would then presumably increase the concentration within the grains, thereby increasing the locking of the dislocations. In the second case, the increase in ky with increasing grain size would be attributed to the nature of the grain boundary itself. One of the several ways of deriving the Hall-Petch equation19 is based on the stress concentration arising from a pile-up of dislocations at the boundary. The ability of the stress concentration to unlock a source in a neighboring grain would depend on the strength of the grain boundary. As is well-known, the nature and struc-

Jan 1, 1963

By Harold A. Krueger

FACILITIES and mining operations of the National Lead Co., St. Louis Smelting and Refining Division, near Fredericktown, Mo., are situated in a famous mining area. Copper, lead, nickel, and cobalt have been mined here for more than 100 years, work having been started on a high sulphide copper outcrop in 1847. Lamotte sandstone is characterized by differential compaction on a rigorously eroded pre-Cambrian surface. The Bonneterre formation was therefore a good host for minerals not generally found in mineable quantities in these midwestern areas. Unusually complex minerals, however, make beneficiation difficult, and because of irregular ore thicknesses and elevations many engineers and operators have not attempted to mine the property. Others have tried who failed. This paper deals with economic, efficient, and competitive methods of mining these highly irregular orebodies, as compared to the open-stope, room-and-pillar methods normally used for horizontal-bedded lead deposits. For the purpose of this study it should be understood that the ore is found in two distinctly different types of occurrences, one to be designated as basin ore and the other as contact ore. Mining of basin ore is complicated by many faults, fractures, cross faults, and breaks. Contact ore is complex because it is found on flanks or slopes of pre-Cambrian knobs or highs. The dip of the mining floor for the latter type varies between 18" and 45". Occurrences of both types of ore are complicated by water courses or solution channels which carry unconsolidated shale, lime, sand, and dolomite. This material is also found between the bedding planes of the members of the Bonneterre formation. The water found where there are fractures, faults, and channels makes it very fluid and tacky, see Fig. 1, particularly after it has been blasted and handled by loading and hauling machines. Much of the ore can be wadded and thrown without dispersing. During early operations by the Buckeye Copper Co. in 1861 and the North American Lead Co. from 1900 to 1910, conventional narrow-gage railroad and side dump mine cars were used with hand shoveling. The complications of mining the contact ore, the only type attempted at this time, can be appreciated when it is realized that operators were obliged to use mules for haulage. Haulageways constructed on these slopes were of necessity similar to wagon trails or goat trails up the side of a mountain. In other words, it was merely a matter of going from side to side of the strike length of the slope, gaining a little in elevation on each shuttle trip. Production totaled only one to two tons per manshift. A few years later, about 1913, the property was purchased by combined Canadian interests known as the Missouri Cobalt Co., and the use of trolley locomotives was initiated. Between 1900 and 1928 a land agent using churn and diamond drilling methods prospected scattered sections of the area. In 1928 the first property was purchased by the present company, then operating as the St. Louis Smelting and Refining Co. Check drilling and prospecting was carried out by the company at various times between 1928 and 1939 to correlate the erratic mineralization. Much information about both types of orebodies was accumulated, but it was still questionable as to whether money should be invested to work these occurrences. In anticipation of high lead and copper prices, about the time World War II started, it was decided to develop and bring into production some of this ore. In 1942 No. 1 shaft was put down on the largest basin-type orebody and in 1943 No. 2 shaft was put down on contact-type ore. Operations were expanded when No. 3 shaft was completed in 1943, and progressed further in 1948, when National Lead Co. dewatered and opened No. 5 and 6 mines, old workings of the North American Lead Co. and the Missouri Cobalt Co. Because of the differential compaction of Lamotte sandstone over the pre-Cambrian porphyry, in some instances mineable thicknesses of basin-type ore occurred 20 to 30 ft above the sand. This is the exception rather than the rule, since most of the mineralization starts at the sand and is variable in thickness. The ore was attacked, therefore, by development drifts and crosscuts at the lowest possible elevation, where the ore immediately overlying the Lamotte sandstone could be drained and made accessible for mining. It was planned to connect to the drifts and crosscuts with raises to mine ore deposited 20 to 30 ft higher. The higher orebodies were thus mined as slusher levels. Slusher hoists were used to drag the ore into the raises, which were made into hoppers. The ore was then loaded into 32x32-in. ore cans, hauled to the shaft by battery locomotives, and hoisted by the conventional Tri-State method. The rate of efficiency was 5 to 6 tons per manshift underground. The contact-type ore was attacked in a similar way, except that the orebodies were not nearly so wide, so that they were more flexible for slusher loading into cans. This advantage was offset, however, by haulage complexities, since the railroad was constructed on steep slopes. Through experience and ingenuity, many improvements were made in mining both types of ores. The two levels, so-called, in the basin-type ore-bodies were connected as previously planned, more efficient locomotives replaced the older ones, and a

Jan 1, 1954

By W. E. Bron, E. S. Machlin

GRAIN boundary migration in V-shaped thin specimens of high purity silver was studied. Each specimen contained two crystals having the relative orientation: (111)A/(111)B; (ll0)A/(101)B. The boundary between these two crystals varied between a continuous curved and an alternating two plane interface. The plane interfaces were oriented parallel to (101)A/(011B) and (121)A/(211)B. Traces of these planes are shown in Fig. 1. Evidently the two plane interface, although of higher area, comprises lower total interface energy than the average curved boundary it replaced. The plane boundaries were found to move at 650 °C to consume the broad segment of the V opposite to the direction of interface area and energy decrease. On investigation, using the thermal etching technique of Hendrickson and Machlin,1 it was found that the outer grain contained 8.3x108 more dislocations per cm" than the grain at the apex of the V. Consequently, the boundary moved to decrease the strain energy associated with the difference in dislocation density across the boundary. The rates of motion of specific {110} and {112} boundaries were measured during interrupted anneals at 650°C by referring the position of the boundaries to each other and a fiducial line on the specimen surface. The measured rates of motion are 0.075 and 0.025 mm per hr for the {110} and {112} boundaries, respectively. Plots of grain boundary motion vs time of annealing show straight lines with little deviation of data points from these lines.

Jan 1, 1957

By K. T. Aust

It is proposed that the intergranular corrosion of austenitic stainless steels is associated with the presence of continuous grain houndary paths of either second phase, or solute segregate resulting from solute-vacancy interactions. Experimental observations of structural changes and crrosion behavior of different types of austenitic stainless steel provide support for this poposal. On the basis of this model, it is shown that the intergranular -corrosion susceptibility of austenitic stainless steels in nitric-dic hromate solution may be substantially reduced either by suitable heat treatments or by impurity control. AUSTENITIC stainless steels, such as Type 304, generally have excellent corrosion resistant properties when properly solution heat-treated and used at temperatures where carbide precipitation is slow. However, several corrosion environments have been found which produce intergranular corrosion of solu-tion-treated stainless steels, that is, those steels with no detectable carbide precipitation.''2 Of the various corrosion environments, the most widely used test solution has been the boiling nitric-dichromate solution. In these acid solutions, stainless steels have been found to be susceptible to intergranular attack despite the addition of carbide-forming elements such as titanium or columbium, or despite lowering of the carbon content or use of high-temperature solution treatments. Studies of the electrochemical mechanism of corrosion attack have been made by several worke1s3'4 who found that oxidizing ions such as crt6 depolarize the cathodic reactions and consequently raise the open-circuit potential of stainless steel immersed in nitric acids. As a result of this, the anodic reaction is accelerated. The reason for the localization of anodic activity at the grain boundaries, and resulting intergranular corrosion, has not been conclusively determined. Several workers, e.g., Streicher,3 and Coriou et al.,4 have suggested that the strain energy associated with grain boundaries provides the driving force for the accelerated intergranular corrosion. This argument would predict that alloys of high purity would still be susceptible to intergranular attack. However, work by chaudron5 and by ArmijO,6 has shown that high-purity alloys are immune to attack, in disagreement with this argument. An alternative suggestion is that chemical concentration differences exist between grains and grain boundaries, that is, impurity segregation at boundaries, and that these chemical differences provide the driving force for localized attack. It is this impurity segregation which can lead to accelerated dissolution of grain boundaries when the alloy is exposed to a suitable corrodant. This mechanism would predict the immunity of high-purity alloys to inter-granular attack, which is in agreement with experi-mental observations. In the present paper, some recent studies on inter-granular corrosion of austenitic stainless steels which were conducted by coworkers and myself will be re-tibility A simple model will be described in which it is proposed that the intergranular corrosion of aus-tenitic stainless steel is associated with the presence of continuous grain boundary paths of either second phase or solute-segregated regions.* On the basis of this model, it is suggested that the intergranular corrosion rate can be markedly reduced by the formation of a discontinuous second phase at the grain boundaries if the discontinuous second phase incorporates the major part of the segregating solute, drained from the grain boundary region. Results are presented of corrosion tests and electron microscopic studies of different types of austenitic stainless steel after various heat treatments which provide experimental support for this model. Finally, a solute clustering mechanism, based on a solute-vacancy interaction, is shown to be consistent with the results obtained for inter-granular corrosion of solution-treated austenitic stainless steels. EXPERIMENTAL Corrosion tests using weight loss measurements were made on sheet specimens, which were lightly electropolished, washed, and immersed in boiling (115°C) 5 N HN03 containing 4 g crt+6 per liter added as potassium dichromate. Studies in which the inter-granular penetration depth was measured both by electrical resistance and metallographic methods have shown an empirical correlation between the rate of intergranular penetration and the weight loss per unit time for identically treated specimens of stainless steel." As a result, although all the corrosion data reported here are in terms of simple weight loss measurements, these data are considered to reflect primarily the rate of intergranular dissolution. Fig. 1 shows a typical result of intergranular attack of a solution-treated Type 304 stainless steel after 4 hr in a boiling nitric-dichromate solution. The wide grain boundary grooving at the surface, and the attack at incoherent twin boundaries, are evident; very little corrosion attack is seen at the coherent twin boundaries. INTERGRANULAR CORROSION MODEL

Jan 1, 1970

By E. Mille, R. Geffken

The Mg-Si and Mg-Ge phase diagrams were rede-levtnined by thermal analysis, and the existence of a single congruent melting compound in each system was confirmed. The melting points of the two compounds Mg2Ge and ,Wg2Si were found to be 1117.4° and 1085.0°C respectively. The euteclics for the Mg-Ge system occur at 635.6°C (1.15 at. pcl Ge) and 696. 7°C (64.3 at. pct Ge); for the Mg-Si system the eutectics are at 6376°C (1.16 at. pct Si) and 945.6°C (53.0 al. pcl Si). The phase diagrams and known thermodynamic data were used to calculate activity values for both systems. The activities calculated for the Mg-Ge system agreed very well with those previously published. Partial molar enthalpy values for the Mg-Si systetn were calculated from the phase diagram for the composition region where no experimental values have been reported. THE phase diagram for any system is an important source of thermodynamic data. Steiner, Miller, and Komarek1 have derived equations which permit calculation of the activity in binary systems with an inter-metallic compound! if the liquidus and enthalpy data are known. The thermodynamic properties of the Mg-Ge and Mg-Si systems have recently been determined in this by by an isopiestic method, and it was considered that it would be interesting to compare these directly determined values with those computed from the phase diagram. The basic features of the Mg-Ge and Mg-Si systems are essentially similar. The one intermediate compound present in each system. Mg2X, crystallizes in the antifluorite structure and melts congruently. Raynor4 has accurately determined the temperature and composition of the magnesium-rich eutectic in both the Mg-Ge and Mg-Si systems. Klemm and West-linning5 investigated the entire Mg-Ge liquidus, employing sintered alumina crucibles; the purity of the magnesium and germanium starting materials was not reported. The melt was not stirred, and the temperature was automatically recorded to an accuracy of ±3°C. The authors reported large weight changes due to magnesium evaporation between 50 and 67 at. pct Mg. The Mg-Si system has been studied by a number of investigators, and the results have been compiled by Hansen and Anderko.6 Significant discrepancies exist between the two principle investigations of voge17 and Wohler and Schliephake.8 Two different grades of silicon were used by Vogel, one of 99.2 pct purity and the other quite impure, containing 6 pct Fe and 1.7 pct Al. The magnesium purity was not specified. The melts were contained in graphite crucibles with porcelain thermocouple protection tubes under an atmosphere of hydrogen. Samples weighing 10 g were rapidly heated to 50° to 100°C above the liquidus: held, and then rapidly cooled without stirring. Accuracy was ±1 at. pct which is equivalent to a maximum error in temperature of ±18°C. Wohler and Schliephake used 97.9 pct Mg and 99.48 pct Si. The graphite crucibles contained a stirrer and the 15-g samples were melted under an atmosphere of streaming hydrogen. The samples were chemically analyzed after each run. Because of the scarcity of the data, the impurity of the starting materials, and the resultant uncertainty and inconsistency in the published liquidus values, it was decided to undertake a reevaluation of the Mg-Ge and Mg-Si phase diagrams by thermal analysis. EXPERIMENTAL PROCEDURE Alloys were prepared from 99.99+ pct Mg (Dominion Magnesium Ltd.) with impurities in ppm: 20 Al, 30 Zn, 10 Si, <1 Ni, <1 Cu. <10 Fe; 99.999 pct Ge (United Mineral and Chemical Corp.), and 99.999 pct Si (Wacker Chemie Corp.). All graphite parts were machined from high-density (1.89 g per cu cm) G-grade graphite obtained from Basic Carbon Corp. with a total ash content of 0.04 pct. Boron nitride parts were machined from rods of National-grade H.B.N. boron nitride. All graphite and boron nitride pieces were baked out under running vacuum at 1100°C for 24 hr before us Cylindrical graphite crucibles (1; in. OD, 23/4 in. long, l3/8 in. ID) were tightly closed with threaded graphite covers which had 21/4-in.-long thermocouple wells and 1/4-in.-diam off-center holes for stirrers. The cover and thermocouple well were machined from a single piece of graphite. A stirrer was made from a flat cylindrical graphite plate perforated with five 3/16-in.-diam holes and a 1/2-in.-diam central hole, and was held parallel to the crucible bottom by a 1/4-in.-diam. 4-in.-long graphite rod which screwed into the plate and extended up through a tightly fitting hole in the crucible cover. An iron core enclosed in a glass capsule was attached to the stirrer with an 18-in.-long molybdenum wire, so that the stirrer could be magnetically raised and lowered from outside the system. One crucible and stirrer with essentially the same dimensions given above was made entirely of boron nitride. Chunks of magnesium were premelted, cast into 11/2-in.-diam. rods, and then cut into lengths varying from a to 1 in. A 5/16-in. hole was drilled through the center of each piece to accommodate the thermocouple well and the individual pieces were then cleaned and rinsed with acetone. The total weight of an alloy was 50 to 70 g in the Mg-Ge system and 40 to 60 g in the Mg-Si system. The pure components were weighed to an accuracy

Jan 1, 1969

By John Griffen

DURING the past year, purchases of coal-preparation equipment and the discussions and plant-scale tests conducted indicate that much attention is being given to better recoveries of coal by preparation plants and improved quality of the finer sizes to widen their market. In the anthracite regions the new equipment was predominantly for the cleaning of the steam sizes, much of it for treating No. 4 and No. 5 buckwheat. The units installed were largely coal-washing tables, Hydrotators, and Menzies cone separators.

Jan 1, 1944

By Anthony G. Reid

INTRODUCTION At the time of the death of Mao Tse-tung in 1976, China was a major oil producing country with a daily oil flow in the order of 1.735 million barrels. This position had been achieved with minimal assistance from the outside world. Further, only some fifteen years had elapsed since the country&apos;s daily oil production capacity had hovered at the barely significant level of one hundred thousand barrels. Why then did the new leaders of China, after this very creditable record of success, suddenly change the direction of the country&apos;s drive for future hydrocarbon production? First, by switching much of the emphasis of exploration from onshore to the offshore continental shelf basins, and further by apparently abandoning the philosophy of self reliance calling upon the world&apos;s oil industry to share in the task of locating and developing these potential offshore energy reserves. The answer is probably only partly understood by those of us outside China, However, a number of factors exerting an important influence on this decision can be identified. THE MOVE OFFSHORE The new leadership was anxious to rapidly move China into her rightful place amongst the powerful and technologically advanced nations of the world. Modernization became the slogan, specifically modernization on four fronts, agriculture, industry, technology and military with the goal to "catch the west by the year 2000". But how to generate the capital to finance this massive modernization program? The rapid escalation of the price of crude oil following the 1973 Oil Embargo and the continuing apparently insatiable world demand for this now extremely precious primary resource was very clear to all. China, as a major producer, could export crude to help finance the ambitious development programs of the government. To do this, however, would require a very significant in¬crease in present production capacity, as the domestic demand even for China with her relatively low per capita energy consumption, is essentially equal to the current production. Trying to rapidly move the new regime&apos;s programs into actions, one can only assume that the planners looked at the success of the petroleum industry over the preceding fifteen years and quickly concluded that this well established curve could be maintained and indeed steepened with an increase in effort. The rapid discovery of a few more Daqing&apos;s (China&apos;s premier oil field, producing one million barrels a day) would have the country&apos;s ambitious modernization goals within reach. Petroleum would At the time of the death of Mao Tse-tung in 1976, China was a major oil producing country with a daily oil flow in the order of 1.735 million barrels. This position had been achieved with minimal assistance from the outside world. Further, only some fifteen years had elapsed since the country&apos;s daily oil production capacity had hovered at the barely significant level of one hundred thousand barrels. Why then did the new leaders of China, after this very creditable record of success, suddenly change the direction of the country&apos;s drive for future hydrocarbon production? First, by switching much of the emphasis of exploration from onshore to the offshore continental shelf basins, and further by apparently abandoning the philosophy of self reliance calling upon the world&apos;s oil industry to share in the task of locating and developing these potential offshore energy reserves. The answer is probably only partly understood by those of us outside China, However, a number of factors exerting an important influence on this decision can be identified. THE MOVE OFFSHORE The new leadership was anxious to rapidly move China into her rightful place amongst the powerful and technologically advanced nations of the world. Modernization became the slogan, specifically modernization on four fronts, agriculture, industry, technology and military with the goal to "catch the west by the year 2000", But how to generate the capital to finance this massive modernization program? The rapid escalation of the price of crude oil following the 1973 Oil Embargo and the continuing apparently insatiable world demand for this now extremely precious primary resource was very clear to all. China, as a major producer, could export crude to help finance the ambitious development programs of the government. To do this, however, would require a very significant increase in present production capacity, as the domestic demand even for China with her relatively low per capita energy consumption, is essentially equal to the current production. Trying to rapidly move the new regime&apos;s programs into actions, one can only assume that the planners looked at the success of the petroleum industry over the preceding fifteen years and quickly concluded that this well established curve could be maintained and indeed steepened with an increase in effort. The rapid discovery of a few more Daqing&apos;s (China&apos;s premier oil field, producing one million barrels a day) would have the country&apos;s ambitious modernization goals within reach. Petroleum would be the principal bridge to the bright future. The next decision involved the question of where to look for these vast new reserves. Chinese exploration teams had already looked at most of the onshore sedimentary basins and, while they were the first to admit that there was much yet to do, it was fairly clear to them that the potential for large new accumulations was confined to two areas: the little explored, remote, inhospitable regions of western China, principally Xinkiang Province and the equally unexplored offshore basins of the continental shelf and slope. In both cases China faced a very serious problem. The inhospitable environments were severely straining her petroleum industry&apos;s current technological ability to cope, particularly as the government needed rapid results. Thus the pragmatic and, to the foreign oil industry, unexpected decision to invite cooperation with the outside world. The reasons for the initial emphasis on the exploration of the offshore basins with the cooperation of foreign oil companies are again supposition on my part, but probably involved considerations of technical merit, ease of development and delivery to markets together with more sensitive issues such as controling the influence of foreign philosophies and values on the Chinese population by containing most foreign activity to the offshore. So within three years of the death of the great helmsman, China had developed a plan to involve foreign oil companies, both state and private, in a grand plan to rapidly increase the nations oil production. In fact, by this time, the first round of talks had been concluded and the first phase begun, and what a beginning. Some forty eight companies from thirteen countries had signed documents to participate formally in this world scale event. It was far easier to list those companies which did not participate than to list those which did. FOREIGN COMPANY INTEREST Why the rush by the world&apos;s oil industry to be involved in China? What was China offering which made everyone so anxious to join in? Again the answer is complex in detail, but principally involved a combination of factors which together caused this virtual stampede. Timing was a major element. Oil Companies, despite an ever increasing take by governments, were beginning to benefit. from the&apos; rapid escalation of crude prices induced by OPEC and were looking for suitable areas to reinvest these funds. Producers

Jan 1, 1982

Jan 1, 1926

By H. Foster Bain

AFTER all, mineral sanctions are not a measure of peace, they are a measure of war, and we must regard them as such. We have had two examples now in the world-first, Italy, and secondly, Japan-where we have applied sanctions. When we got ready to apply sanctions to Italy that would hurt, they went to war. In the Far East, when we applied sanctions against Japan, in the latter part of 1941, there was a quick reaction, and the Japanese bombed Pearl Harbor.

Jan 1, 1944

By Hermann Bach, Walther Hänig, Willi Gehrhardt, Ernst Theurich, Walter Langner

With the construction of the Magdeburg zinc works, the Georg von Giesche&apos;s Erben Mining Co. of Breslau has to a certain extent completed the program of reconstruction which it set as its goal after the boundaries of Upper Silesia were drawn by the Treaty of Versailles. During its history, covering.more than two centuries, zinc and lead mining has been its chief activity. Through the new boundaries established, it lost to Poland all its mines and smelters, including five distillation smelters. Of its extensive properties, there remained only an apparently unimportant and unexplored portion of the old Bleischarley ore field which, however, happily made possible the resumption of its old business. In 1925 the Deutsch-Bleischarley shaft-only a few kilometers from the old Bleischarley shaft—was sunk and developed, and in May 1926 production of lead and zinc ore was resumed. As facilities for smelting were lacking, the ore was at first delivered to the neighboring smelters, which had now become Polish. Realization of the plan to build its own zinc works had to be postponed at first for lack of capital. In the meantime, however, plans for the new works were worked out in all details. After extensive experimentation in a semicommercial pilot plant it was decided, at the end of 1928 and the beginning of 1929, to use the electrolytic process and, for economic reasons, to place the works at Magdeburg. With zinc at the approximate price level that had ruled since the Deutsch-Bleischarley mine had begun working, it was hoped that the plan could be completed in 1930 with the company&apos;s own resources. However, falling metal prices, already noticeable in 1929, made this impossible, and further postponement for a time became necessary. Finally, at the end of July 1933, the funds for building the works became available, in the form of a loan granted under the first employment

Jan 1, 1937

By J. B. NEALEY

MANY nonferrous smelting plants have recently adopted natural gas as fuel with resultant economies, both in cost and efficiency of utilization. Not only has this fuel been used for roasting, reduction, sintering, drossing, and smelting, but also for power. All of the three big smelters near Salt Lake City, Utah, have been changed over from coal and oil firing to gas. Among these is the plant of the International Smelting Co., Tooele, an Anaconda subsidiary, smelters of both copper and lead ores. In the roasting division at Tooele are 32 MacDougall six-hearth roasters, each 16 ft. in diameter and 19 ft. high. Two gas burners are installed on each furnace. These burners are of the single-valve, automatic gas-air proportioning type using high-pressure gas at 10 lb.

Jan 1, 1933

By E. M. Furness, A. S. Henderson

ORIGINALLY the Babbitt experimental plant grinding circuit consisted of one rod mill 10 ½ ft diam by 12 ft long in open circuit followed by two ball mills 10 ½ ft diam* 12 ft long in parallel circuit. Shortly after operations commenced it was apparent that the rod mill could not function satisfactorily at the required 125 gross tons of ore per hr. Attempts to operate at this rate produced: 1) excessive tramp material over rod mill trommel screen which could not be handled in this open circuit and 2) excess build-up of coarse ore in the ball mill circuits because of inadequate rod mill grinding. Since Reserve Mining Co. ore must be ground to 85 pct -325 mesh to produce a satisfactory iron concentrate, an efficient and controlled grinding circuit is highly important. The first step in trying to resolve this grinding problem was to determine which unit of the circuit was actually in trouble and to what extent. A series of tests conducted at a lower tonnage rate of rod mill feed indicated that one ball mill could grind satisfactorily at rates up to 70 gross tons of rod mill feed per hr.

Jan 12, 1957