Search Documents

By R. D. Pehlke, J. V. Gluck

The effect of small additions of silver on the actiziity of zinc in dilute solution with molten bismuth has been determined ill the range 450° to 650°C. Experimental measurements were made in a multi-electrode galvanic cell. All zinc activities showed large positive deviations from Raoult's Law. The results are expressed in terms of the interaction parameter EJ, as defined by Wagner. In the binary Zn-Bi system, Henry's Law was followed at zinc concentrations below 5 mol pct, thus indicating that the binary or self-interaction parameter of zinc in bismuth is essentially zero. The Henry's Law con- THE determination of thermodynamic interaction parameters requires accurate knowledge of solute activities in the dilute-solution region. Dealy and Pehlke1 have summarized the basis for interaction relations, discussed some theoretical implications, and presented a compilation of interaction parameters calculated for molten nonferrous alloys from stant ranged from 2.43 at 650°C to 3.96 at 450°C. The binary zinc activities were consistent with published data for higher zinc concentrations . The ternary interaction parameter ranged from -1.90 at 650°C to -3.30 at 450° C, varying linearly with the reciprocal of the absolute temperature. The negative value for the parameter reflects the fact that addition of silver decreases the activity of zinc in solution with bismuth. data available in the literature. Most of the data were for two-component systems from which only the self-interactions, Ei, could be calculated. Concentration ranges were often such that a considerable extrapolation was required for calculations at lnfinite dilution. The data for ternary systems were quite limited and often unavailable in suitable systematic fashion—thus few values of the parameter e| could be obtained. Knowledge of both the binary and ternary interaction parameters is necessary for the estimation of the activity coefficient of a given dilute solute in

Jan 1, 1965

By George Sachs, J. Spretnak

The process of recrystallization has not as yet been explained satisfactorily. Some definite conclusions could be drawn from recent investigations, such as, for example, that recrystallization is a process of nucleus formation and crystal growth1 and that the orientations of the nuclei correspond to some fragments of the original crystals, which have been considerably distorted during deformation.2 There are, however, a number of metals and alloys crystallizing in the face-centered cubic system, which form a particularly simple orientation if recrystallized as a sheet.3 Such a shect is almost a single crystal with the cubic axes parallel to the rolling, transverse, and normal directions of the sheet. This preferred cubic or (100) orientation of the recrystallized sheet has been considered to be very different from the rolling structure of the same metals,4 but there are two reasons why this last supposition remains open to controversial discussion. The first reason is academic: In practically all cases except the one mentioned above, close correlations and similarities between rolling and annealing orientations have been observed; for instance, in iron and steel sheet.6 Secondly, no deformed metal actually forms a simple orientation. In any thoroughly investigated case a number of different orientations and considerable scattering or deviations from the ideal orientations have been found.6 It is generally true that investigations on single crystals have shown that a definite orientation is approached in stretching or in compression of an originally undisturbed crystal.7 In the special cases, however, where the initial orientation was close to an important crystallographic direction that differed from the final "ideal" orientation, the resulting orientation changed very little by deformation, staying somewhere in the vicinity of the initial orientation.8 Such deviations

Jan 1, 1940

By S. S. Clarke

THEN sufficient ore has been blocked out on a lease to warrant a shaft, the proposed. Location of the shaft should be carefully considered, as the old promoter's method of sinking wherever his hat landed is a sad mistake as some: of us have learned by trying to operate such mines. In some instances certain conditions exist, such as mill location, railroad right of way, etc., that necessitate a change of location from the. ideal, but under average conditions and with the knowledge of the formation gained from the drill logs and with the general trend of the orebody known, the shaft can be located from. the standpoint of its future relation to the mine with re-gard to hauling and' hoisting a maximum tonnage: at a minimum cost per ton, also taking into account the minimum amount of expense and trouble- in sinking. Quite a few shafts are located in the wall of a run or just in the thin edge of the orebody: As a general rule the formation here is solid and permits rapid and safe sinking, and the shaft pillars are left in practically valueless material. This permits the withdrawal of pillars and still keeps the shaft protected. By opening a shaft in thin ground, you are not tempted to cut it high, wide, and handsome, but to shape it up-with ample clearance for lay-bys and with more of an idea of permanency, as a few hundred extra dollars spent around the shafts for proper track installation will re-turn, a good rate of interest in ease of handling "cans," quick get-away; and fewer wrecks. Nearly all the shafts in this district are sunk on a contract basis, the con-tractors furnishing all labor and explosives, and the company building the sinking-derrick, dump-track, and furnishing, all equipment, material, and power. The following costs are the averages, for three shafts sunk through good solid formation, with no water to, contend with, and approximately 260 -ft., deep, having about-100 ft. of shale. The contract price was $9 per foot with the shale and $13 per foot in the solid, making a total of $2,980 paid to the contractor. The wages paid by the contractor were, $5 per shift for the hoist-man, who also sharpened steel, $6 for the lead shaft man, and $5 for the helper;, the cribbing was sawed on contract for 40c. per shaft: foot; about. 94 board feet. of cribbing was used per foot of staggered cribbing and 168 board feet per foot of solid cribbing.

Jan 8, 1928

By N. Lilienberg

During the past fen- years, the requirements for steel have been raised so high that soundness is more important than ever before. The old practice mas to make steel ingots of suffciently large sections to permit a considerable reduction of area in rolling and hammering to a given size, relying on the fact that by such rolling and hammering all cavities will be squeezed together and practically eliminated. The finished sizes, if found by inspection of the surface to be faultless, were therefore pronounced to be sound. But when such steel is " worked up," the manufacturer is surprised and disappointed to find that it splits, or that streaks and seams make the product unmarketable. Large sections, such as rails, beams or heavy forgings, may, within certain limits, be sufficiently strong, even if the sides of the cavities are only squeezed, and not welded, together. But it is well known that, in the interior of heavy articles, under certain conditions, forging may develop small streaks into large cavities. Small sections, steel for ordnauce and tubes, and numberless articles in the tool-trade, always show up the defects. It may be doubted whether cavities in steel ingots can ever be completely welded. The old theory is, that the silver-clear blow-holes, without the blue oxide, can be welded by suffcient working. They are, however, not empty, but are filled with carbonic oxide. It is admitted that the " blue " cavities, resulting from air mechanically drawn down into the mold during the casting, can never be welded, because the oxide does not melt, and there would be no escape for it if it did. The only way in which steel can be made satisfactory for the above-named particular purposes is by having it " dead molten." But then the trouble of piping is encountered. As is well known, a pipe is the result of the contraction of the liquid interior after the surface of the ingot has become solid by contact with the mold. When this contraction is partly

Jan 1, 1907

Through the generosity of Sir Robert Hadfield, Honorary Member, the Directors of the American Institute of Mining Engineers are enabled to announce the Hadfield Research Prize of $1,000 for the best contribution to the publications of the Institute upon the general subject of The Different Forms and Combinations of Carbon with Iron, including those in Iron Alloys. The prize will be awarded at the Annual Meeting of the Institute in February, 1916, to the best paper upon this subject which is presented to the Institute before Nov. 1, 1915, provided such paper is deemed worthy by the Institute's Iron and Steel Committee. The following suggestions are also added for the guidance of those who may take part in this research. While it is not desired to define closely the exact lines or scope of the proposed research, as it is advisable to make these as broad as possible, the object in mind may be said to be generally as follows: To elaborate and find out the best methods of determining the forms of carbon in steel or iron, including those in iron alloys. A portion of the work would probably be a continuation of the researches which have in the past been carried out by Jullien, Abel, Muller, Ledebur, T. Sterry Hunt, Akerman, Arnold, Stead, E. D. Campbell, Hogg, Parry, Upton, and others.Through the generosity of Sir Robert Hadfield, Honorary Member, the Directors of the American Institute of Mining Engineers are enabled to announce the Hadfield Research Prize of $1,000 for the best contribu¬tion to the publications of the Institute upon the general subject of The Different Forms and Combinations of Carbon with Iron, including those in Iron Alloys. The prize will be awarded at the Annual Meeting of the Institute in February, 1916, to the best paper upon this subject which is presented to the Institute before Nov. 1, 1915, provided such paper is deemed worthy by the Institute's Iron and Steel Committee. The following suggestions are also added for the guidance of those who may take part in this research. While it is not desired to define closely the exact lines or scope of the proposed research, as it is advisable to make these as broad as possible, the object in mind may be said to be generally as follows: To elaborate and find out the best methods of determining the forms of carbon in steel or iron, including those in iron alloys. A portion of the work would probably be a continuation of the researches which have in the past been carried out by Jullien, Abel, Muller, Ledebur, T. Sterry Hunt, Akerman, Arnold, Stead, E. D. Campbell, Hogg, Parry, Upton, and others.

Jan 1, 1917

By Charles Becker

THE practice of drying phosphate in Florida is as old as the industry, which began a little more than half a century ago. The methods, however, have changed considerably. At first, the natural process of exposure to the sun and air was used, later supplemented by wood fires beneath open-air stationary dry kilns and drying towers of various designs. It was not until the early nineties that rotary driers came into use, and at first they were of very small design and fired with wood. As the industry grew and tonnage increased, so likewise grew the number and size of rotary driers, until today the largest installations are 6 ft. up to 7 ft. 6 in. in diameter, and 55 to 60 ft. long, fired with crude oil. The reasons for drying phosphate rock are: (1) to eliminate freight on water in the shipment and (2) to facilitate the good grinding qualities required by the buyers in their acidulation. Phosphate pebbles vary materially in natural characteristics and each property has a direct bearing on the processing. In making comparisons of cost and operating conditions, the following are usually taken into consideration: 1. The hard dense pebbles, which contain very little interior moisture and 6 to 8 per cent total moisture, usually produced from the low-grade deposits. 2. The lighter, porous pebbles, which contain 4 to 5 per cent interior moisture and a total moisture ranging from 9 to 15 per cent. 3. The product of recovery operations using oily reagents, containing from 15 to 25 per cent moisture. 4. The size of the pebbles. Usually the plus 5-mesh material is considered as "coarse rock"; the minus 5-mesh plus 24-mesh is "fine rock," and the minute particles below 24 mesh are called "concentrate." 5. The amount of moisture allowed in the dried product. The practice is generally to dry down to 1.5 to 2 per cent moisture. There is, however, an actual range in guarantee of from 1 per cent maximum to 3 per cent maximum.

Jan 1, 1936

By Lucius W. Mayer

The iron-mines of the Ilsede Hutte Co. are at a town called Peine, about 20 miles east of the city of Hanover, on the railroad to Brunswick (Braunschweig). Hanover, the capital of the province, is a military city, of approximately 250,000 inhabitants, and Brunswick, 33 miles to the westward, has half this number. The mines here described are located in a hamlet called Bulten. The Ilsede Hutte Co. operates two mines, 1.5 miles apart, in this district, Gruber Bulten Adenstadt and Gruber Lengede Bodenstadt. It also operates an iron-mine north of Hanover, known as Eiserhaven, and one in the Harz mountains, the Georg Friedrich, at Grauhof. At Bulten a coarse conglomerate, a, Figs. 1 and 2, contains nodules of limonite, cemented together by calcium phosphate. The ore contains Fe, 25 to 45; Mn, 3 to 4; P, 0.6 to 1.4; '5, 0.02 to 0.09; and CaCO,, 40 per cent. Directly above the conglomerate is limestone, 6, followed by a mixture of clay and sand, c. Below the conglomerate is a hard clay floor, d. The ore-body, from 10 to 12 km. long, and from 3 to 4 km. wide, has a maximum thickness of 20 m. It dips approximately 10" S.E., and strikes K 45° E. Diamond-drill prospecting shows that the thickness diminishes to 1 m. as the end of the deposit is approached to the northward. At this point the deposit is 250 m. below the surface. In Fig. 2, the arrow, A, indicates the general direction of the work along the face, a, which is carried forward in a straight line for its entire length. At B, a train is approaching, which has come from the bench-track, shown at C, by a circuitous route, and is dumping the overburden behind the face, in the space left by the excavated rock. Formerly the work at this mine mas essentially open-cut, the deposit having a very strong outcrop. Figs. 1 and 2 show also

Jan 1, 1909

By H. R. Shidel

This paper summarizes the results obtained from the preliminary cementing of wells in an effort to cut off the bottom water. The object of this work was two-fold: (1) To prevent the oil sand from becoming flooded. (2) To plug off bottom water, thereby preserving the individual well and reclaiming production. Valuable suggestions and help have been given by the following named: Messrs. Kyle and La Velle, of the U. 8. Bureau of Mines; Magnolia Petroleum -Co.; Freed Oil and Gas Co. The cementing work was carried out under the personal supervision of L. J. Snyder. In an unpublished paper on the "Water Problem in the Augusta Field," 5. K. Clark reaches the following conclusions: (1) That the great amount of water present is bottom water, occurring in the Varner sand, the main producing or the 2500-ft. horizon, (2) That the only striking connection between structure and water is in .the area of the marked fault on the Ralston, E. C. Varner, and F. Varner leases in sections 8, 9, 16 and 17. (3) That the oil occurs in porous streaks, generally separated by finegrained, well cemented sand, which is barren. Possibly two or three such pay streaks may be found. That under a pay, fine-grained sand occurs, which is presumably barren at the time of drilling, but soon reveals water. The writer takes partial exception to the last point, because well defined shale, slate, lime, or hard sand breaks have been encountered in a great many cases, separating the pay streaks under which water is often found. This is not an invariable occurrence, as cases have been noted when the oil has been followed immediately by water in the same stratum. In an effort to overcome the water menace, the following methods of plugging were tried: (1) Plugging with wood, lead, and limit plugs. (2) Plugging with sand pumpings.

Jan 1, 1920

By Don C. Blackmar

The production of non-ferrous secondary metals has become a large and important industry in the United States, and deals with practically cvery type of manufacturing concern. Its business is unique in that it generally buys frorn its customers as well as sells to them, whether they are individuals, cities, corporations, or the United States government. Its operations are of vital importance to the success and prosperity of nlany of the nation's most important manufacturers; yet there are few industries about which less is generally known by those outside it, whether concerning the rliagnitude of its operations or the details of its actual technique. The industry itself is to blame for this meager publicity, because its technical men have made few attempts to openly exchange ideas, in spite of the excellent examples set by the iron and steel or the copper and brass industries. Whether this is due to the ancient shroud of secrecy generally supposed to cover smelting operations, or because its technical men actually felt that the industry was too puny to be interesting, is hard to say. This paper will consider its subject in a general way, attenlpting to show something of the size and importance of the industry, as well as its fitness to do its work well. Attention will be called to the sound economic reasons for the handling of non-ferrous wastes by specialists, and to the often unseen losses of metals and labor which occur when manufacturc~rs rcclairn thrir own metallic wastes. Magnitude of the Modern Industry No particular thought is given to the kitchen accident whereby a ruined saucepan is sorrowfully tossed into the ash can, yet it is a fairly safe guess that within a month this saucepan, together with hundreds of its follows, will again be in service, perhaps in an autonlobile crankcase, or in an electric vacuum sweeper. It is by this conversion of the useless into the useful, whether from home or large manufacturer, that the secondary tonnage is built up.

By August J. Breitenstein, W. Spencer Hutchinson

The outstanding engineering accomplishment of the last three decades has been the development and application of more and cheaper power and its use instead of the labor of men and animals. Substitution of power for manual labor has taken effect on every hand in the United States. With the aid of energy mechanically available to his hand, one man does the work that only a few years ago required two, three or even a greater number of laborers. The results in respect to the favorable economic effects are well known; namely, increased production, higher wages and lower costs. On the other hand, the vast social effects, both good and bad, have been none the less important, even if less understood and only casually regarded. The chief sources of energy today are the mineral fuels, coal and petroleum. In the United States they yield more than 90 per cent of the total energy demand. Thirty years ago the proportion of energy supplied by the mineral fuels was likewise above 90 per cent, but the division according to origin was very different. These relations are shown for the years 1900, 1930 and 1950 in Table 1. Method or Preparation and Interpretation of Statistical Data The fuels comprised in this study are: (1) the coal group including both bituminous and anthracite coal; (2) the petroleum group, taking in not only petroleum but natural gas and natural-gas gasoline. Natural gas for many years has been used in localities relatively near the wells but statistics were found no earlier than 1910. Demand has rapidly

Jan 1, 1934

By S. H. Davis

The pyrites used in making sulfuric acid in the United States have been largely imported from Spain and Canada, the Spanish imports amounting to nearly 1,000,000 tons per annum in the pre-war period. The greatly increased use of sulfuric acid and the cutting off of these Spanish imports, incident to war conditions, brought about a threatened shortage of sulfur supplies during the war period. The bituminous-coal mines of ccrtain districts have, for many years, furnished a small tonnage of pyrite in the form of coal brasses. A mechanical concentrator at Danville, Ill., for a number of years, has been treating hand-picked lump pyrite and coal from the picking belt and from the mines and a small plant near Gillespie, Ill., for a few months has been recovering pyrite from washery refuse. Many mines throughout Illinois, Indiana, Western Kentucky, Ohio, and Pennsylvania have shipped an occasional car of the hand-cleaned lump pyrite. Only a very small percentage of the available pyrite has been recovered in this way, however, as usually the miners throw such lumps into the gob with slate and other impurities. It has been estimated that the western Indiana coal field could furnish more than 100,000 tons of pyrite per annum. The present production is very small. The possibility of furnishing the domestic trade with pyrites recovered as a byproduct from coal-mining operations appears attractive but there are certain features difficult to overcome. Pyrite, to be used in acid making, must meet with certain requirements as to size and purity. Lump ore for grate burners should be under 3 in. (7.6 cm.) and over 1 in. (2.5 cm.) in diameter. Fines for use in mechanical roasters should be under quarter mesh. The material should be high in sulfur, free from arsenic and phosphorus, and as low in carbon as possible. The pyrite obtained from coal can be made to meet all the above requirements, but it is difficult to remove all the carbon. The pyrite in coal occurs as bands and nodules of varying thickness and size and of comparative purity, but mixed with this is more or less web sulfur. The web sulfur carries admixed coal, which may make the concentrate run up to several per cent. carbon. This makes the concentrates subject to firing, causes heavy consumption of niter, and lowers the acid-plant capacity, due to dilution of gases. The hand-cleaning methods

Jan 1, 1920

By H. T. Mercer, A. C. Paulson

The composition of steel and the theory of its heat treatment have been so ably discussed elsewhere that it is unnecessary to go into the subject here. The purpose of this paper is to describe briefly the method of treating drill steel at the Copper Range mines, giving some of the troubles encountered and the manner in which they were overcome or corrected. To study the matter properly, it was necessary to devise a system of records that would show the actual underground performance of the drills. To illustrate this system, the records of the Champion mine are used, as it is at this mine that most of the work along these lines has been done. Reports from each drill machine are made daily by the shop and mine, and tables compiled from these reports show the footage drilled, steel broken, drills received and sent out at the shop, drills sharpened, and bits cut off. These data show what each machine or party is doing and whether the miners' supply of drills is kept up to date. There have been times when the supply of drills has been short and time lost by the miner in looking for drills. The daily records show the number and condition of drills on hand at all times. Under the old method of sharpening, the drills were heated in a coke furnace, the proper degree of heat being judged by color. Then they were sharpened in a machine, reheated in a second coke furnace where the proper heat was again determined by color, and quenched in water. While this method was fairly successful in the hands of a careful workman and for the solid steel used in the old piston drill machine, the introduction of the faster water machine, using hollow steel, produced changes both underground and in the shop. Much more was expected of the hollow-steel and hammer-type machine, with its improved method of rotation, but troubles due to breakage, burnt bits, uneven tempering, etc., at once appeared.

Jan 1, 1922

By R. E. Reed-Hill, J. L. Martin

Kinking is an important deformation phenomenon in poly crystalline a zirconium. The crjlstallo-gvaphic features of the most important form of kinking have been determined with the aid of twins formed at 77°K in grains previously kinked at high temperatures. It has been .found that the kink-band boundaries correspond to walls of edge dislocations with (1150) Burgers vectors and dislocation lines parallel to (1070). The present observations imply that basal slip is an important secondary-slip mode in polycrystalline zirconium. Previous single-crystal studies13 did not veveal this mode Other evidelzc.e for (0002)(1120) slip is also presented. ThE first studies of kinking in hexagonal metals were made by orowan,1 using single-crystal cadmium wires. He suggested that this was a new de- formation mode in metals, different from ordinary glide or twinning. Next, Hess and Barrett2 studied zinc-crystal rods in compression, and were able to offer an explanation of the phenomenon described by Orowan. They concluded that kinks required no new deformation mechanism and were a special form of deformation band that developed gradually and solely from basal glide. Similar kink bands were then observed by Washburn and parker3 on zinc crystals deformed in tension at low stresses and high temperatures. In titaniun,4 kink bands associated with {1010}<1120> prism slip have been observed in coarse-grained specimens. Magnesium5 and rhenium6 have also been observed to kink in conjunction with their basal- and {1010} prism-slip systems, respectively. Yttrium has (1010) as a predominant slip plane, but no observations of kink bands were reported.7 Since no previous investigations of kink bands in zirconium have apparently been made, this study was proposed. Its aim was to determine the crys-tallographic features of a type of kink band frequently observed in polycrystalline zirconium. EXPERIMENTAL APPARATUS All tests were performed on a type TTC Instron machine. The cross-head speed usually chosen in tension or compression was 0.02 in. per min. Ten-

Jan 1, 1964

By C. S. Smith, Chih-Chung Wang

D. Turnbull—In the opinion of the writer the most interesting result described in this paper is that the distribution of tin with respect to solidification temperature has several fairly well-defined maxima. It appears that each peak may be associated with a catalytic impurity of some rather specific composition. Recently we have obtained some additional evidence in favor of this viewpoint in experiments on the supercooling of lead droplets coated with different surface films. The distribution of lead droplets, ostensibly coated with lead sulphate, with respect to solidification temperature exhibited two distinct and reproducible maxima, one at 20" supercooling and the other at 47". On the other hand, when the droplets were ostensibly coated with halide films, no solidification was perceptible until the aggregate was supercooled more than 55". Upon further cooling a single well-defined peak centering at 60" supercooling was observed. Since the particle size distribution was the same in these two sets of experiments it appears that the most reasonable interpretation of the results is that the sulphate surface film or its reaction products with lead are much more effective in catalyzing the nucleation of lead crystals than are lead halide films. C. S. Smith (authors&apos; reply)—Dr. Turnbull&apos;s experiments with lead drops coated with various surface films are most interesting. However, before drawing conclusions from the cooling curves described in the paper as to the existence of a few nucleus types effective at a few different temperatures, one must consider the state of subdivision of the liquid metal. In the A1-Sn alloy used, the tin was not in uniform droplets but tended to collect in three distinct shapes—in long interconnecting prisms along grain edges, in somewhat elongated interdendritic branching pools. and in isolated droplets. A single nucleus will solidify only the metal in contact with it, and the heat evolved will be proportional to the connected volume. A uniform distribution of nuclei of random effectiveness in such an alloy will cause peaks on the specific heat curve on cooling, which correspond to the volume distribution of tin and tell nothing about the nucleus type. In any real alloy both effects will be combined, and it seems impossible at present to distinguish between them. M. B. Bever—The thesis of this interesting paper is supported by a combination of positive and negative evidence. The authors have shown that under certain conditions a liquid phase may undercool, if it is dispersed in a thoroughly discontinuous manner throughout a solid matrix. They also found that undercooling

Jan 1, 1951

By S. D. Brady

In Monongalia County, West Virginia, the Pittsburgh and Sewickley beds lie west of the Monongahela River and underlie practically all the western end of the county. The average thickness of the Pittsburgh bed is 8 ft., where it is being mined at present, sometimes running up to 9 ft. The Sewickley bed is 4½ to 6 ft. thick and lies 90 to 100 ft. above the Pittsburgh bed. As the Pittsburgh bed had a known value, a large part of it was bought up without consideration of the Sewickley bed. When the Monongahela Railway was built up the west side of the Monongahela River, other interests bought up the Sewickley bed, as it was found to be equal in quality to the Pittsburgh, with slight local exceptions. The two beds, therefore, were owned by different people, and naturally each owner opened his mine and ran it without regard to the working of the other bed. Consequently, considerable portions of the upper bed were seriously affected for economical mining, especially on Scotts Run. In recent years there has been a tendency, influenced by the decision of the West Virginia Supreme Court, on the part of the operators in Monongalia County to try to coordinate their projections in the layout of their mines. A typical geologic section, according to the report of the West Virginia State Geological Survey on Monongalia County, agrees with Fig. 1. It is apparent that the rock above the Sewickley bed and between the Sewickley and Pittsburgh beds is of a rather friable ~lature, therefore it is easily broken in pillaring. About the only difference between this section and the geologic section in the Lowsville district is that in the latter district the rock between the coals is a denser sandstone and contains little shale and limestone and no evidence of Redstone coal. It is a laminated sandstone, and although it makes a harder mass, it is easily broken. While working in the Lowsville district, the author had an opportunity to examine a neighboring mine in the Sewickley bed, which was over a section being pillared in the Pittsburgh bed. The two mines belong to dif-

Jan 1, 1931

By Thomas Leonard Watson

Sulphide ore-bodies of more or less lenticular shape occurring in metamorphic crystalline schists, gneisses, and slates, and conforming closely in strike and usually in dip to the inclosing rock, have been recognized and described along the Atlantic seaboard from Quebec to Alabama. The ore-bodies do not entirely conform, in all cases, to the structure of the inclosing schists, but they sometimes cut across the foliation in dip, though conforming more closely with the direction of strike. In composition the principal sulphide mineral is usually py-rite or pyrrhotite, or both, accompanied by copper, frequently gold, and almost always some sphalerite and galenite. Other metallic ores are, so far as these sulphide bodies have been investigated, less common; silver is not uncommon, and in some of the pyrrhotite masses nickel is present in quantity sufficient to be commercially valuable. Cobalt frequently accompanies the nickel, usually in smaller amount, and the two vary much in relative proportion. Quartz and calcite are probably the most common of the non-metallic minerals. A number of silicate minerals are frequent representatives in one place or another ; garnet, am phi-bole, biotite, pyroxene, zoisite and others. The sulphide bodies of Virginia, comprising both pyrite and pyrrhotite, are among the most extensive along the Atlantic seaboard. Among the pyrite bodies may be mentioned the well-known and extensively worked mines of Louisa and Prince William counties, located on the main pyrite belt (A, Fig. 1) of the middle and northern, eastern Piedmont region in Virginia, and among the pyrrhotite bodics is the famous " Great Gossan Lead" (13, Fig. 1) of the Floyd-Carroll-Grayson coun-

Jan 1, 1908

By H. E. Lee, A. W. Edelen

The Teziutlan copper-zinc deposit is supposed to be of late Cambrian or early Paleozoic age. The country rocks are a series of schists or phyllites, flat lying and in the form of a plunging anticline. The ore deposit occupies a single horizon in the schist for a known horizontal extent of 1200 meters. Along its strike occur four large lenses or ore bodies. These ore bodies occupy positions along the flank and extend to the crest of the anticline. The primary mineralization is in the form of quartz, pyrite, sphalerite, chalcopyrite and galena, with a few scattered silver anti-monides. Quartz and pyrite form the mineralization between the ore lenses. Ill the ore lenses the sulphides appear as a massive, very fine-grained intergrowth of minerals. The intergrowth suggests a contemporaneous deposition of the heavy sulphides. The grain size, usually under 0.09 mm., makes the separation difficult and fine grinding important. The ore bodies were formed at great depth by solutions probably originating in the same basic magma that gave rise to the dolerite sills that are so common in their vicinity. Introduction The Teziutlan copper-zinc deposit is distinctly different from other ore deposits of Mexico in age and type. Previously stated to be pre-Cambrian in age, it is now quite generally supposed to belong to the late Cambrian or to the early Paleozoic period. Also, in contrast to the usual shallow-vein zone type of mineralization in Mexico, there is here exemplified an intermediate vein zone deposit of copper and zinc. So far as is known, the Tezintlan vein is unique in the history of Mexican geology and in a class by itself, its closest counterpart probably being the copper veins of the pre-Cambrian of Canada. The Teziutlan district is in the extreme northwestern corner of the State of Puebla, Mexico. Teziutlan, the terminus of a branch line of the National Railways from Mexico City, is connected to the mine at Aire Libre by a 17-km. narrow-gauge railroad owned and operated by the Teziutlan Copper Co. Owing to excessive grades on this short linc, Shay-geared locomotives arc used for the transportation of concentrates and supplies.

Jan 1, 1941

WILLIAM B. PRICE* and PHILIP DAVIDSON, ? Waterbury, Conn. (written discussion?).-A few months ago we became interested in deter-mining the properties of. pure nickel as a metal for certain uses and arranged, in cooperation with the International Nickel Co., a series of tests on cold-rolled so-called pure nickel and both longitudinal and transverse specimens annealed at 100° intervals from 250° to 1050° C. Since our tests confirmed; in a general way, the observation put forth by Messrs. Browne and Thompson, they are given at this time. A bar of hot-rolled nickel about 9 in. (23 cm.) wide and 1/2 in. (12.7 mm.) thick made by the International Nickel Co. -of grade A stock, analyzing nickel plus cobalt 98.48 per cent., iron 0.67 per cent., manganese 0.27 per cent., carbon 0.07 per cent., silicon 0.162 per cent., sulfur 0.033 per cent., and copper 0.22 per cent., was cold-rolled down to a final thickness of 0.134 in., malting a 73.2 per cent. reduction by rolling. Test specimens, 9 by 1 in., cut parallel (marked longitudinal) and normal (marked transverse) to the direction of rolling were milled to give a test section 2 5/8 in. long by 0.5 in. wide. Three specimens each, longitudinal and transverse, were annealed at one time in a nichrome-ribbon-wound tube furnace. The temperatures were taken with a Pt-PtRh thermo-couple in conjunction with an Engelhard millivoltmeter. An annealing period of .) 2 hr. plus 25 min. preheating was used in all cases. Sclero-scopic and Brinell hardness tests and static tensile tests were made on the rolled and annealed specimens. The tensile tests are shown in graphic form in Fig. 7. The Brinell and scleroscopic values are given herewith.

Jan 11, 1919

By A. R. Kinkel

Robert T. Walker and Woodville J. Walker (Walker Engineering Corp., Salt Lake City)—Mr. Kinkel&apos;s article embodies, in condensed form, the results of the first detailed and complete geological survey that has ever been made of the long neglected but potentially very important West Shasta Copper-Zinc district, in Shasta County, California. In view of the difficulties of the terrain and the complexity of the geological structure, this represents a notable achievement, and it is with regret, therefore, that the writers find it necessary to differ from Mr. Kinkel&apos;s conclusions on two important points. The first has to do with the interpretation of two members of the stratigraphic column of formations in the district; for purposes of comparison, the description of these two members according to Mr. Kinkel is shown parallel to the description of these members according to the writers, see Fig. 14, Mr. Kinkel&apos;s nomenclature being used. The first member, which Mr. Kinkel terms the upper unit of the Balaklala rhyolite, consists of a single, massive, homogenous body of very silicious igneous rock, consisting almost wholly of quartz and albite, and averaging about 80 pct silica. Most geologists of the U. S. Geological Survey who have previously inspected the district have called it an alaskite. It is not a pile of several members, but is a single unit, without internal subdivisions. It has the form of a recumbent lens, approximately flat on the bottom and arched on top, several miles in diameter, and attaining a maximum thickness of 1000 to 1200 ft. It varies in texture from porphyritic to holocrystalline, and contains unusually large quartz phenocrysts up to 4 mm diam. Mr. Kinkel considers this formation to be a thick lava flow that is older than the overlying Kennett shale, while the writers interpret it as being intrusive, constituting a domed sill or laccolith that is younger than the Kennett shale. Their reasons are as follows: 1) This formation shows none of the features which within the writers&apos; experience invariably accompany very silicious lava flows. Nowhere is it vesicular; nowhere does it contain any glass or its devitrified equivalent; nowhere does it contain flow breccia; and nowhere has it a ragged top, in spite of the fact that there is no evidence of surface erosion, which might have removed such a top.

Jan 1, 1957

By T. A. Rickard

MILLING is one of the metallurgical arts whereby the extraction of the largest possible proportion of the value in an ore is effected at the least possible expense. Stamp-milling* is that particular process in which a heavy body of iron is caused to fall upon the ore so as to disintegrate it and thereby induce a separation between what is valuable and what is worthless. The latter is usually less in specific gravity, and is therefore, by the further aid of water, removed from the former, which is then collected by the use of mercury. Several similes have been employed to describe this process. The stamp has been likened to a hammer of which the stem is the handle and the die the anvil. The ore upon which the stamp falls has been compared to a nut awaiting the descent of the hammer whose blow is to separate the valueless shell, the quartz, from the valuable kernel, the gold. When we begin to pursue our inquiries, however, we find that the analogy is just sufficiently true to emphasize the departures from it. The hammer falls, the anvil is fixed; so with the stamps and the mortar. The anvil is made of softer metal than the hammer; so also the die is often, and should be always, of steel or iron less hard and more tough than that of the shoe. The movement of the hammer and the drop of the stamp are both intermittent. In regard to their intermittent action, as in many other respects, stamp-mills arrange themselves under two types, which, though apparently contradictory, have both been evolved from a common original, and are united by a great variety of intermediate modifications. The slow speed and the high drop of the mills of Gilpin county Colorado, appear to have very little in common with the fast speed and short drop of those of the main gold belt of California; yet the practice of the one was largely derived from that of the other,

Jan 1, 1894