Search Documents

By John R. M. Hill, Gerald Zink, Fun-Den Wang

The work described in this paper is sponsored by the Bureau of Mines for the purpose of accelerating the drilling of roof bolt holes and reducing the quantity of materials needed to fill each hole. A high-speed, small-hole drill has been fabricated and tested in the laboratory. High Priority has been given to safety, reliability, and compatibility with underground coal mining practice. The combination of drag bits and erosion jets is designed for high penetration rate, long wear life, and uniform hole size in a variety of sedimentary strata. A reliable high-pressure, high-speed swivel feeds water to the bit at about 4 L/min (1 gpm). The duplex hydraulic intensifier which drives the jets has a 40-kW (30-hp) capacity. Results of recent full-scale laboratory testing (Now. 1977) are presented.

Jan 12, 1979

By M. Semchyshen, G. A. Timmons

P. A. Beck (University of Illinois, Urbana, 111.)—An interesting result of this work is the fact that in cold rolled molybdenum sheet complete loss of work hardening is obtainable on annealing, without change in texture. The retainment of the cross-rolling texture on soft-annealing is particularly significant, since this is essentially a single orientation texture, where texture retainment could be achieved by only one of the two niechanisms which produce this effect in aluminum,16 namely by recrystallization in situ. Recrystallization in situ was originally discovered by Collins and Mathewson (1940) and by Crussard (1944) as a phenomenon taking place on annealing in relatively mildly deformed single crystals of aluminum. It now appears to be a major (in many cases the major) mechanism of annealing of severely cold rolled poly-crystalline material, not only in aluminum,le but in metals as different in character as beryllium," tita- nium,'" and molybdenum. All these data now confirm the general validity, at least for more or less pure metals, of the interpretation of the annealing process given a few years ago by Smith.'" The whole question of recrystallization is now reopened. Indeed, it appears that recrystallization, as defined traditionally, may not occur at all, since at the time "deformed material" is absorbed by "recrystallized grains," it has already become completely strain free by recovery and "recrystallization in situ."

Jan 1, 1953

By L. W. Eastwood

PART 1. EFFECT OF HEATING RATE UPON RECRYSTALLIZED GRAIN SIZE OF ALUMINUM AND ALUMINUM ALLOYS AMONG those concerned with the annealing and heat-treating of aluminum and aluminum alloys, it is well known that after cold-working a coarser grain is usually produced by slow heating than by more rapid heating. Consequently, for the control of the grain size produced by annealing or heat-treating cold-worked aluminum and aluminum alloys, the heating rate is of considerable practical importance. References in the current literature on the effect of heating rate are numerous, but it appears neither necessary nor desirable to give here a review of the former work done on this subject. It became evident during some preliminary work on the recrystalliza-tion of aluminum and aluminum alloys that the effect of heating rate depended upon the type of microstructure of the metal. This observation led to the following study of the relationship of the type of microstructure of the alloy to the effect of the heating rate.

Jan 1, 1939

Jan 1, 1932

By H. H. Clark

ELECTRICITY must be safeguarded everywhere that it is used. The conditions that exist underground make the use of safeguards more essential there than almost anywhere else. Electric Shock Electric shock is the greatest danger in connection with the use of electricity in mines, because conditions existing underground are so favorable to its occurrence. Men are often obliged to work in more or less uncertain light near bare wires that are carrying dangerous potentials. The fact that the men are standing on the earth practically connects them to one terminal of the electric generator. The most dangerous piece of electrical equipment underground is the trolley wire. It is necessarily bare and extends for long distances throughout a mine, often less than a man's height from the track rail. Sometimes the making up of trips of cars must be done near low-hanging trolley wires. All bare wires offer the same danger that trolley wires do, although not to the same extent. Apparatus that has accidentally come in contact with the ungrounded side of an electric circuit is almost as dangerous as the trolley wire. A severe and even fatal shock may be obtained by coming in contact with the frame of a motor or a switch box that has become charged with electricity, or "alive," as it is usually termed. It is also possible to obtain shocks from the frames of locomotives and cars if track. sanding, poor bonding or a similar cause has put a high resistance to earth in the path of the current.

Jan 4, 1914

By Paul M. Musgrove, Larry S. Diaz

Recent tests conducted at Inspiration Consolidated Copper Co. examined some aspects of the value of a continuous measurement of particle size to the operation and control of a mill grinding circuit. Inspiration's control objectives and kinds of control systems developed in recent years to attain these objectives are outlined. A description is given of the arrangement of the test circuit at Inspiration and also of the systems used to measure particle size of the cyclone overflow product in these tests. Use of on-line size measurement for the analysis and improvement of grinding circuit performance is illustrated by relating how two important relationships were detected. Finally, the performance of a particle-size-based control system is described, including preliminary conclusions as to increased productivity.

Jan 1, 1974

By R. T. Murrill

BLOCK-SIGNAL and dispatching systems have been in use on surface railways for years, but only recently have they been applied to underground mining conditions. Formerly, all ore was moved underground by hand tramming; the surface openings were numerous and fairly close to the ore being mined. As the tramming distances increased, animals were brought into service. Then came the locomotive, and since its introduction, haulage lines have gradually been reduced to fewer levels and to fewer surface openings until more than 20,000 tons are being handled daily on one level in some of the larger mines. Under the, se conditions many trains must use the same-tracks, and signal systems have become necessary. In some cases it has been found more advantageous to use train dispatchers than to install signal devices. The dispatcher may be simply a flagman at a busy point or he may have mechanical signals to operate at more distant points. At the inspiration mine, Inspira-tion, Ariz., the station is equipped with a switch-con-trol board, whereby the dispatcher throws electrically all track switches in a certain block, which gives him complete control over all trains passing through that block. In a few cases, dispatcher stations are established in connection with a signal system.

Jan 2, 1922

By Robert C. Meaders, Arthur R. MacPherson

Many attempts have been made to eliminate most of the crushing plant and all the grinding plant in the process of ore beneficiation by substituting a combined crushing and grinding unit which could take coarsely crushed ore and reduce it to a fine size in one unit. This unit normally would have no other grinding media than the ore itself. This is true autogenous grinding, as we understand it today, and should be clearly distinguished from pebble mill grinding, where pebbles are substituted for steel balls to grind a ball mill size feed. To compete in efficiency with normal methods of crushing and grinding, the autogenous mill must use less labor and steel to produce an equivalent product at equal or lower power consumption. In general terms, a unit to perform these functions must have means to crush the ore to fine sizes and to then further reduce the crushed pieces by grinding. In other words, to do efficient autogenous grinding, there must be a proper balance established between crushing and grinding rates. There is not much point in crushing at too fast a rate if the grinding means are not present to reduce the small particles to the required product size. The crushing means used in an autogenous mill are impact forces of two kinds, namely, (1) the rock travelling at high speeds striking the shell, and (2) the lifters travelling at high speeds striking the rock. Grinding is probably effected in a manner equivalent to pebble milling.

Jan 9, 1964

By C. D. Broadbent

Open pit blasting can be a low cost routine or a high cost bottleneck depending on geology, environment and the operator's ability to master site conditions. Because blasting is a repetitive operation, there should be ample opportunity to optimize the process; but ordinarily this optimization is rarely achieved and then only if conditions remain consistent and predictable. Often, however, and particularly with porphyry coppers, hidden differences in rock characteristics nullify the operator's best efforts. At a porphyry copper deposit being mined by Kennecott Copper Corporation, all of the following rock types occur; oxidized and fresh porphyry, altered and silicified limestone, explosion breccia, rhyolite, sandstone, shale and several others. The units can cover large areas or be limited to a few tens of feet in maximum dimension. They are rarely visible on the bench surface and often do not show up in the bench slope. Even though the blastability of these rocks varies substantially, a generally-uniform blasting pattern was formerly used with disappointing results. Secondary blasting was often required and high bottoms occurred frequently, overblasting wasted drilling time, and explosives caused excessive throw.

Jan 4, 1974

By E. A. Stevens

IT has been ascertained in recent years that certain rocktypes, geological formations and structural conditions may be used as fairly reliable guides, when prospecting in recognized mineral belts or mining districts, with a reasonable certainty of discovering "pay-ore;" and that such is considered as a practically established conclusion may be inferred from a perusal of the recent reports of the U. S. Geological Survey and the literature of the several scientific societies discussing minim, geology, and kindred subjects. Cripple Creek is no exception to this conclusion, and the rock-type or association, rather than the structural condition, is the most infallible guide.† These guides consist of four, possibly five, dike-rocks, three of which are extremely basic, while the fourth is an acid rock of an entirely dissimilar character. The basic rocks are nepheline-basalt, limburgite, feldspar-basalt and tephrite. There are grounds, however, for believing that the two latter are subdivisions of one type, and therefore will be described under one head. The acid rock is quartz-porphyry. Nepheline-basalt is-a rock encountered in but few localities elsewhere on this continent, and occurs in narrow dikes cutting various formations. When typical‡ it is composed of

Jan 1, 1913

By John Bell

Aim of Rock-Crushing Experiments THE aim of the laboratory experiments described in this paper was twofold: 1. To measure as accurately, as possible the maximum amount of crushing that can be effected by 1 hp. acting for 24 hr., by the two proposed methods for measuring the amount of crushing, namely: (a) by Rittinger's method; (b) by Stadler's method, based on Kick's law. 2. To show, if possible, that by one of these methods, the amount of crushing produced by 1 hp. in 24 hr. is a constant amount throughout a wide range in the diameter of the piece crushed, and that by the other method, the amount of crushing is a variable quantity over the same range of diameter; or else show that neither of the proposed methods for measuring the amount of crushing indicates a fixed relation between power and crushing and consequently a new method for computing this amount will have to be found to permit the establishment of a law of crushing. Experimental Methods Testing machines, calorimetric methods and commercial. types of rock-crushing machines were considered with reference to their value for measuring power used in crushing. The following electrically driven crushing machines, installed and available in the McGill Ore-dressing Laboratory and which had been used in previous rock-crushing tests, on the whole seemed especially suited to the investigation: (1) Comet "A" crusher; (2) 7 by 9-in. Dodge crusher; (3) 10 by 16-in. rolls. In later tests a 3 ½ -ft. Huntington mill was used.

Jan 2, 1917

By K. J. Miller, R. E. Hucko

The Coal Reparation Division of the Pittsburgh Mining Technology Center conducted an investigation to assess and compare the pyritic sulfur reduction potential of coal-pyrite flotation and high-gradient magnetic separation (HGMS). Tests were run on three coals - an Upper Freeport bed coal, a Lower Kittanning bed coal, and a Pittsburgh bed coal - to establish grade-recovery relationships characteristic of both processes. Representative portions of each coal sample were crushed to two top sizes-nominal - 500 pm (-35 mesh) and nominal - 149 pm (-100 mesh)-and subjected to conventional froth flotation. The froth product was then beneficiated by coal- pyrite flotation or HGMS, to provide a direct technical companion of the two processes. At - 500 pm (- 35 mesh), the size normally employed for coal flotation, both coal-pyrite flotation and HGMS effectively separated pyrite from coal, and the performance of the two processes was essentially the same. At a - 149 pm (- 100 mesh) sire, however, the performance of HGMS exceeded that of coal-pyrite flotation. The separation effected by HGMS were more efficient at - 149 pm (- 100 mesh) than at - 500 pm (- 35 mesh). On the other hand, it was concluded that either the effectiveness of coal-pyrite flotation decreases with diminishing top size or the process has not been optimized to treat material finer than 500 pm (35 mesh).

Jan 1, 1983

By C. W. Crispell

THE four nomograms presented in this article were designed to simplify and make more, rapid the calculations connected with the compression and transmission of air. The formulae involved are rather complicated, but the graphic solutions are simple; their use requires an ability to follow explicit directions and to interpolate values on a logarithmic scale. ? For the sake of convenience, the nomograms will be divided into two classes, and the purpose and accuracy of each will be discussed. Compression It is frequently desirable to determine the horsepower necessary to compress a given amount of free air from atmospheric pressure to a certain final pressure. The nomograms in Figs. 1 and 2 present a rapid method of calculating the horsepower required to compress 1 cu. ft. of free air per minute by single or two-stage compression. The general formula for the horsepower required to compress air adiabatically is: HP = S X 144/33,000 PVn/(n-1) [(P'/P) n-1/Sn -1] (1) where: P = absolute atmospheric pressure at compressor, in pounds per square inch. P' = final absolute pressure of compressed air, in pounds per square inch. V = volume of free air compressed per minute, in cubic feet. S = number of stages. n = exponent of the compression curve.

Jan 6, 1917

By Axel Sahlin

The day is long past when linen and cotton rags were the exclusive raw material of the paper-trade. Wood-fiber, chemically or mechanically prepared, straw, hemp and Esparto grass have largely supplied the demand, which the old materials did not suffice to fill. But even these newer fibers have been of late supplanted, to some extent, by mineral pulp. Weighting and filling materials have also been resorted to, partly to give body to the fabric, partly to increase its weight and reduce the cost per pound. China clay, sulphate of lime and soapstone have generally been employed as loading materials. Even though these materials lack fiber, their addition must by no means be viewed, as it too generally is, entirely as an adulteration. No doubt, to a certain extent, they weaken the paper ; but for ordinary grades the addition of these non-fibrous substances is a positive advantage, as they close the pores between the fibers and lend to the paper a great degree of opaqueness and a superior finish. Fibrous talc, as a form of pulp, has the same effect, without appreciably weakening the paper. When, therefore, some fifteen years ago, fibrous talc in large quantities, and of marvellous purity and whiteness, was discovered in the neighborhood of the town of Gouverneur, it was not long before the

Jan 1, 1893

By F. T. Davis

The annual review of mineral dressing was the subject of considerable discussion at the MBD meeting in New York last February. Because the amount of material now being published is so imposing, it was generally agreed that reviewers should try only to cite the items of importance. In order to conserve even more space, it was agreed to omit bibliographies. In reading these reviews, and those of the past two or three years, one is impressed by the advances in materials handling, the enlargement and the advances in automation of unit process equipment. Although there has been development of a variety of new concentration principles in flotation, magnetic separation, et al., the design of these principles into new plants has not been widespread. The probable reason is that the plants being built today are so large and costly that few are able to face the risk of any significant degree of experimentation. There are exceptions to this; for example, some of the chemical processes, but these are usually because there was no conventional process available. This situation should change in time as the ores amenable to our conventional methods become depleted.

Jan 2, 1967

By L. W. Rowe, W. R. Opie

A brief history of TiCI, production and purification is given. Chlorinator feed materials for the production of TiCI4 are classified. The thermodynamics and kinetics of Ticl4 production by chlorination of TiO2 are discussed. Problems encountered in the chlorination and purification steps are outlined in detail. MOST of the current processes for the production of titanium metal require the use of TiC14 as a source of titanium values. This material can only be produced by a dry chlorination process, since it is immediately hydrolyzed in the presence of water. When pure, the tetrachloride is a colorless liquid boiling at 136°C. It fumes readily in moist air, reacting immediately with the moisture to form TiO, and HC1. History The tetrachloride was prepared as early as 1826 by DumasL who chlorinated a red hot mixture of carbon and TiO,. Since then, numerous other mixtures have been used including rutile, ilmenite, beneficiated ilmenites, titanium pigment, slags, and the various titanium metalloids such as TiN, TiCN, TiOC, and TiS2. S2Cl2, phosgene, and CC14 have been substituted for chlorine and CO has been used in place of carbon.

Jan 1, 1956

By N. C. Gay, P. J. Van Der Veever

The Klerksdorp gold mining district, South Africa, experiences a relatively high level of seismicity with many seismic events of magnitude greater than 4. These large events appear to have foci close to fault planes, most of which displace the strata by several hundred metres over a wide area. To help understand the mechanism of these large mining- associated seismic events, in situ stress measurements were made at 4 sites using "CSIR doorstopper" strain relief techniques. The sites were chosen close to, or some distance from fault planes and other structures. The results show that at all 4 sites a relatively large horizontal stress is oriented approximately north- west. The magnitude of this stress ranges from 0,78-1,O of the vertical stress. A marked horizontal stress anisotropy, varying from 13-30 MPa is also present. The dominant structural features are large, north-east striking normal faults which extend across the entire length of the goldfield. Displacements across these faults vary from a few centimetres to several hundred metres. Bedding plane faults across which large displacements may occur are also common as are north and north-west striking dykes. The majority of the faults strike at approximately 90º to the maximum horizontal stress and at all sites a large compressive stress plunges in the direction of dip of the strata and fault planes. Thus a significant shear stress may act across suitably oriented planes causing them to be in a state of potentially unstable equilibrium. This abnormal stress situation would exist along the entire length of the fault

Jan 1, 1982

By G. L. Oldright

DURING 1919, in the face of high cost for labor and supplies and a rapidly dropping copper market, the management of the Ohio Copper Co. of Utah was left with an orebody that had been shown to be very low grade, and a mill that could not make a satisfactory recovery, even by flotation, because a considerable proportion of the copper minerals was oxidized. About seven million tons had been mined by the use of a caving system, the best of the broken ore extracted and milled, and the nature and copper content of the rest of the orebody fairly well determined. The rock of the whole mine was shown to run between 0.3 and 1.3 per cent. in. copper. As, the Ohio Copper orebody lies at the contact of the original sandstone (now altered to quartzite) with the quartz monzonite intru-sion that was the source of the mineralization at Bingham Canon, the rock was thoroughly shattered. It was shown further that the rock was mostly quart-zite, with a few quartz-monzonite "fingers" projecting into it. Although some of the old cleavage planes had been healed by resilicification so as to leave some of the copper minerals disseminated in the rock, a large proportion of these minerals was distributed along the cleavage planes.

Jan 10, 1923

By A. M. Crawford

INTRODUCTION Grouting is an engineering operation which has been practiced for many years and a considerable amount of experience and skill has been developed in this field. However, a review of the current literature (Houlsby, 1982) reveals that the theoretical background and experimental observations that are necessary to adequately predict or describe the performance of a particulate grout (e.g. cement based) in a jointed geologic media are somewhat inadequate. In the near future it is envisaged that the use of grout and grouting techiques will be used to tackle even more difficult problems than have been considered in the past. One problem that is currently being faced by the rock mechanics engineer is the development of geologic repositories for the disposal and containment of high level radioactive waste. In such structures there will be only one opportunity to ensure the success of the containment system. This success will depend to a large extent on the adequate and successful performance of the grout curtains to be utilized around the shafts and shaft liners. Regrouting will not be possible. There are other problems in rock mechanics in which it is frequently necessary to inject particulate media into passages of small dimensions, and where typically the size of fracture being injected is of the same order of magnitude as the particle dimension. For example, in the oil industry in hydraulic fracturing the enhancement of fracture conductivity is maintained by means of proppants introduced into the fracture.

Jan 1, 1984

By S. F. Shaw

Fox some time it has been more or less recognized within the industry that a scientific control of flowing wells would result in increased production and a greater ultimate recovery of oil. About two years ago it was proposed by the writer that this control should follow principles worked out by him while handling large air-life operations. In the case of wells that had ceased to flow where a large quantity of liquid was present, the use of these principles would result in a large increase of production by using compressed air or gas to flow the well; in the case of a well flowing naturally it would take the form of controlling the gas associated with the oil, resulting either in immediate increase of production or in a reduction of the gas consumed per barrel of oil, and in both cases would result in a greater ultimate recovery from the sand. The Roxana Petroleum Corp., appreciating the advantages to be obtained by a scientific application of the principles of the air lift to oil wells, recently engaged, for a limited time, the services of the writer to work out some of the problems involved. The work was carried out at Braman, Garber and Tonkawa in Oklahoma, and at Oxford in Kansas. Following some suggestions of the writer a well was also equipped by the Roxana company at Smackover by A. S. Field.

Jan 11, 1926