Search Documents

By Thomas B. Dellinger

Since 1950, rotary-drilled, large-diameter holes, "big holes", with depths to over 300 ft and diameters of over 30 in., have become numerous and widespread. 50 such holes have been drilled for access shafts to LPG mined caverns. Over 70 holes have been drilled for various other commercial activities. Over 150 holes have been drilled by the AEC for atomic testing purposes. These holes have ranged up to 300-in. diam with 1600-ft depths, 120- in. diam with 570-ft depths, and 72-in. diam with 4800-ft depths. Equipment is now available to drill a wide range of big holes for varied requirements. At least a dozen drilling contractors are participating or have participated in the drilling of big holes. The accompanying tables show pertinent historical, technical and economic data on over 250 holes. The purpose of this paper is to present a review of the big hole drilling equipment available, a compilation of the available data on large-diameter holes, to show the experience obtained to date and to show that big hole drilling is feasible and available to the industry.

Jan 12, 1965

The Library of the above-named Societies is open from 9 A.M. to 10 P.M. on all week days, except holidays, from September 1 to June 30, and from 9 A.M. to 6 P.M. during July and August. The Library contains about 55,000 volumes, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library can render valuable service through correspondence; letters requesting information will receive special attention. The Library is prepared to furnish references and copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information as to the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The, time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape. The members of the Institute can be of service to the Library by forwarding copies of mining reports, maps privately issued,-,and similar material, which will be classified, indexed, and made available to other members. Suggestions for additions to the Library, either by purchase or personal solicitation as gifts, will be welcomed. It is hoped that members while in the city will use the Library freely, and assurance is given that most careful service will be rendered to them.

Jan 5, 1914

By C. R. Schumacher, W. H. Moyer

Cornwall, Pa. magnetite ore, containing recoverable sulfides in the form of chalcopyrite and pyrite, has been mined continuously since 1742 1 Beneficiation of the ore was begun in 1905, at the Lebanon concentrator located six miles from the mine. At first, only magnetite was recovered, using Grondal magnetic separators. In 1907, copper minerals were recovered by means of Wilfley tables. Copper flotation, attempted as early as 1912, was finally successful in 1919. In 1940, flotation of the cobalt- bearing pyrite was begun, and Cornwall ore became the major domestic source of cobait for many years. In 1916, the Bethlehem Steel Corp. began to purchase interests in the Cornwall mine and Lebanon concentrator properties, and by 1926 had acquired complete ownership. Metallurgical practice at the old Lebanon concentrator was good, but by today's standards the plant was outdated. The flowsheet was complex, due both to the mineral content of the ore and to the low capacities of much of the equipment. As the flowsheet developed, buildings were added and the plant was spread over a relatively large area, with resulting high manpower requirements. Another disadvantage was the six-mile rail haul from the mine to the Lebanon concentrator.

Jan 3, 1966

Jan 1, 1920

By M. G. F. Sohnlein

IN a Bolivian tin concentrator an appliance was needed to furnish a suitable product for fine jigging from a pulp of the following composition: Mesh Per Cent. +20 8.0 +40 36.5 +60 9.0 +80 10.5 +100 5.5 +150 4.51 -150 25.0 99.0 Loss 1.0 IN the jigging process, particles of cassiterite as small as 0.1 mm. can be recovered, provided they are not present in excess, that is if the material treated on the jigs contains sufficient coarser sands to keep the interstices between the grains open. Removing the fine material from the pulp by screening, to prepare the jig feed, is impractical, because that means the use of an 80-mesh screen or finer, and is not as effective as hydraulic classification. A screen would eliminate mineral grains from the feed which can be recovered by jigging, and in addition would throw more gangue and low-grade middling on to the jig. Formerly a one-spigot Richards vortex classifier had been used to accomplish this separation, but the tangential openings through which the hydraulic water enters became clogged by fine vegetal matter with which the water was contaminated, and which it was impossible to remove from the water. Consequently the work of the classifier was imperfect and a good deal of slime was sent to the jig. When designing the plant referred to in this paper it was decided to use a hydraulic classifier as shown in Fig. 1. The essential features had been copied from the Anaconda classifier.1 This remodeled classifier consists of a truncated pyramidal wooden hooper A with an attachment of cast iron

Jan 4, 1916

By H. B. Fuqua, B. E. Thompson

For a very brief description of the North Texas area, and the general geological features with which it is associated, the reader is referred to the opening paragraph of last year's summary1. A more complete discussion of the structure of the area, together with other interesting data concerning it, has been published recently by the Bureau of Economic Geology at the University of Texas2. It has been impossible for the authors to isolate the statistics for production for each of the many small pools of this district, as such statistics are not kept by operators except by counties or arbitrary divisions of counties. The total number of wells drilled in Archer, Wichita and Clay counties also has been subject to some estimate, as many of the shallower holes are not reported. While both routine development in proven or semiproven areas and exploratory drilling during 1935 showed an increase over the year 1934, the discovery of new producing areas of importance did not show improvement over that period. Several extremely local productive spots within semiproven areas were found in Archer, Cooke and Wilbarger counties; and extensions to older producing areas were developed in Archer, Baylor, Cooke, Montague, Wichita and Wilbarger counties. In Archer County, the Grace and Woods No. 1 Archer County (Fee), 4 miles northwest of Archer City, in the Thomas Glass survey, encountered a sand from 2836 to 2845 ft. of Pennsylvanian (lower Canyon) age, which showed an initial yield of 75 bbl. daily. While its production is of negligible importance, it is given special mention in this review because of the fact that it is producing from a new and deeper horizon than has been previously exploited in the county. Little deep development occurred in the district during the year. The Walter Gant No. 2 C. M. Worsham in J. M. Swisher survey, about 14 miles east of Henrietta, in Clay County, was abandoned at 5127 ft. in

Jan 1, 1936

By Glenn Alvey

THE measure of value of an oil property is approximated by the length of time it takes to "pay out;" viz., the time required for it to return the original investment. This time varies in different fields. In the Appalachian and Mid-Continent fields, a good investment pays out in about four years; in California, it requires a slightly longer time; and in the Gulf field about two years. The two principal methods for establishing these values are based on acreage, as in California, and on production, as in the Appalachian field. The method of establishing values based on production1 was worked out in the Appalachian fields and approximates the value remarkably well in some fields; but it is a rule of thumb and should be used intelligently. Briefly, the method is as follows: An arbitrary number of dollars (called the barrel-day price) multiplied by the number of barrels of settled daily production of the property gives the value.. In its crudest application, the barrel-day price is determined by the "$10 to $.01" rule, which means that the barrel-day price is one thousand times the prevailing price of oil. For instance, with oil at $3.50 per bbl. the barrel-day price would be $3500 per bbl. This rule, however, is not strictly applied, for the, barrel price is varied according to whether or not the wells "hold up." But when a barrel price for a district has been fixed it is quite general to raise or lower the price with the fluctuation in the price of oil; here the" $10 to $.01" rule is used extensively. However, the prospective purchaser takes into account tangible equipment upon the property, the extent to which the drilling program has been carried out, whether or not the wells are "shot" or natural, depth of wells, spacing of wells, paraffin trouble, etc.

Jan 1, 1921

May 219t, 1872. THE Institute assembled in the rooms of the Geographical Society at the Cooper Union, Tuesday evening at 8 P.M. President Raymond called the meeting to order, and introduced Mr. Abram S. Hewitt, who welcomed the Institute to New York. President Raymond, in behalf of the Institute, replied. The President then read the following report of the Council for the past year. The Council respectfully report that the American Institute of Mining Engineers has held four meetings-at Wilkes-Barre, Bethlehem, Troy, and Philadelphia, respectively-all of which have been well attended, and socially and professionally most successful. The proceedings of these meetings having been published in the Engineering and Mining Journal, and sent to all members and associates, are sufficiently well known. Forty-four papers, by twenty-six authors, have been read. These papers embrace s wide range of subjects, and prove the practical character of the proceedings of the Institute. The finances are in a satisfactory condition. By the report of the Treasurer it appears that $1290.10 have been received, $519.90 expended, and that $770.20 now remains in the treasury exclusive of fees for 1872. This fund, it is hoped, will be so increased by voluntary subscriptions as to enable us before long to issue s volume of our most important transactions in a permanent form. The Council has made a favorable arrangement with the Scientific Publishing Company, publishing the Engineering and Mining Journal, by which that journal became the organ of the Institute for the first publication of the proceedings, papers, and notices to members. This arrangement it is proposed to continue through the present year unless the Institute shall otherwise direct. It is not intended to supersede the publication of an annual or occasional volume, but to maintain an interest in the Institute, and to serve the convenience of members while our funds do not permit s more ambitious publication.

Jan 1, 1873

By R. W. Titshall

WHAT IS SAMPLING? We are all involved in sampling almost every day of our lives, by tasting, feeling, or smelling. Most raw materials, food products or manufactured items are sampled several times at various stages of the production process before a commodity of suitable quality can be produced. Data obtained from sampling is used in establishing price, quality control, allocating production costs, or overall process efficiency. The area of sampling outlined in this article is the collection of a small quantity of material from large continuous bulk flows of solids and slurries. The concern in obtaining the sample is that the material obtained is truly representative of the main flow in every respect. The methods and equipment outlined are for the collection of a manageable sample. The sample has to be analyzed in a laboratory to determine its characteristics and compliance to set standards. SELECTING A SAMPLING SYSTEM When selecting a sampling system, it is essential to define the requirements, as to what the actual sample obtained will be used for and what degree of precision is required. Determine whether or not the system has to comply with any set standards such as A.S.T.M. (American Society for Testing and Materials) which have established methods for collection of a gross sample of coal. Sampling which is done for in-plant or process control is not generally governed by set procedures, but similar care should be taken during the selection process so that when the equipment is put into service it will operate reliably and produce a sample which is truly representative of the total material lot or consignment.

Jan 1, 1982

By R. J. Borg, C. E. Birchenall

The self-diffusion coefficients for a iron have been deternzined between 980° and 1167° K using Fe55 as the tracer. With decreasing temperature the diffusivity was found to decrease more rapidly than predicted by the Arrhenius equation in the region of the Curie temperature. The diffusion coefficients obtained well above the temperature of the magnetic transformation are more precise ard differ substantially from all the previously reported values. In the temperature region beginning at least 50" above T,, the diffusion coefficient is given by D = 118 (±2) exp 1 HE self-diffusion coefficients for a iron have been reported previously as the result of four independent investigations The general lack of agreement and the poor precision of most of the previous work prompted the redetermination by the present authors. The possible effect of the onset of ferromagnetism upon the diffusivity5 provided an additional impetus for this investigation. The earlier measurements of Birchenall and Mehl1 gave low values for the diffusion coefficient at temperatures below the Curie temperature, Tc. However, the precision of these measurements is not sufficient to establish an indisputable correlation between the low values and the magnetic transformation. The results of this investigation along with all the previous ones are shown in Fig. 1. EXPERIMENTAL Small rectangular samples, approximately 1 by 0.5 by 0.3 cm, of high-purity iron (Vacuum Metals Corp., "Ferrovac") are first heated in hydrogen at 900°C for24hr in order to remove possible trace amounts of dissolved carbon and oxygen. The small

Jan 1, 1961

By Herbert E. Lindberg

Laboratory-scale intact and jointed rock masses were tested in field and laboratory experiments to investigate tunnel response in high stress environments. In most of the experiments the tunnels were modeled by a rigid-plastic foam polyurethane with a crush strength of 3.4 MPa (500 psi) and emphasis was placed on jointed rock parameters: joint sets (single set of parallel plane joints versus a double set of orthogonal parallel plane joints), joint plane angle with respect to the direct loading direction, and joint spacing. Other parameters were loading stress, loading direction, and tunnel reinforcement strength. Results show quantitatively the increase in tunnel deformation in jointed compared with intact rocks, double versus single joint sets, and large versus small angle between the joint plane normal and the loading direction. A surprising result was the decreases in tunnel deformation with increases in the number of joints across a tunnel diameter. The efficacy of scale modeling with laboratory-constructed rock was tested by modeling complex reinforced concrete and steel tunnel reinforcements in jointed rock masses and comparing the results with large scale tunnels previously fielded in highly jointed granite. Tunnel response was reproduced in surprising detail, including concrete fracture, steel liner bending and fracture, and critical load to produce these responses. The scale models also allowed sectioning of the jointed rock masses to observe gross sliding along the joints that accompanied tunnel failure.

Jan 1, 1982

By Raymond Ladoo

THE milling of talc, as is the case of many non-metallic minerals, until recently, has not received adequate technical consideration, for the talc industry has become of importance only within the last decade. At first, talc was used only in the massive form, for foot warmers, griddles, and so on, and milling methods were unnecessary. As the demand for ground talc increased, producers adopted the machinery used in the milling of flour; in fact, many talc mills were rebuilt flour mills. Improvement has been slow, but today several types of grinding and separating machinery are in use; many of them, however, are still inadequate and inefficient. To determine the best methods of milling talc, it is necessary to understand the essential properties a talc must possess to fit it for a particular use. For toilet purposes, whiteness, freedom from lime and grit, fineness of grain, and good "slip" are essential. As a paper filler or coating, the talc must be white, have a good slip, be free from grit and iron, uniform, and fine grained; freedom from lime is a disputed point. Fibrous talc is supposed to be superior to massive on account of the interlocking of grains in the paper, thus increasing its strength; this point, though, is in doubt. In general, talc for the paper industry need not be of as high quality or as fine grained as that used for toilet purposes. Talc is usually bought by sample, for which reason it is difficult to state the essential properties for use in paint, rubber, roofing, and so on. The adoption of standard screen tests and standard grades by producers is necessary before an accurate basis for manufacturing or selling standards can be established. Off-color tales might be utilized, as in Germany and-Austria, by the establishment of standard grades of colored tales.

Jan 1, 1921

Man: A purely detached consideration of nature and the place of man in it may easily result in somewhat pessimistic conclusions as to man and his destiny. However, when we come to the evaluation of man's role in the development of natural resources and his achievements in this field, a more optimistic tone may be justified. Hence the possible contradictions between Man and Nature, Perfection, and the present chapter are more apparent than real. After all, progress must have a foundation of optimism, and we cannot challenge either the faculty or the students to better work and to a progressive and constructive outlook without an underlying tone of optimism and basic faith in the future. Geology is the basic science of Mother Earth; the science of the natural forces that have produced and modified the structure of our globe; the science of minerals and rocks; of landscapes and soils; of water supply and mineral resources, including mineral fuels; and of the history of life, both plant and animal, as revealed by fossils in rocks. It is difficult to reduce man and his historical significance to their proper relationship with regard to the earth and its history. Processes of rock formation have continued for at least two billion years; man's activities have been in evidence only a few thousand years. As a means of comparison, if the height of the Empire State building were to represent geologic time, the thickness of a nickel placed on the tower would just about repre-

Jan 1, 1950

By Arthur F. Johnson

THE principal costs of making a pound of aluminum are for 9 kw-hr of electricity and for 1.9 Ib of the oxide (A1203) called alumina. A pound of alumina is made by digesting 2 or 3 lb of bauxite in hot caustic solutions, settling and filtering out the oxides of silicon, iron, and titanium and precipitating and calcining the A1203 as a pure, white powder. The cost of foreign bauxite delivered at an alumina plant in the U.S. may equal or exceed the cost of its chemical treatment to make alumina. Some of the principal factors affecting costs in the utilization of foreign bauxites are: transportation from mine to market, mineralogical and physical composition of the bauxite, thickness of the bauxite beds and their clay and forest overburden, amen- ability of the bauxite to beneficiation and to caustic extraction of the alumina, and lastly size of bauxite deposits and rate of mining employed.

Jan 6, 1954

By Michael Hoch

The phase diagrams of binary systems of some of the transition elements of Groups IV, V, and VI were used to compute the partial free energies of these elements and the free energy of formation of their Laves-type compounds. From these data, isothermal sections of ternary phase diagrams were calculated and compared with experimental results. DURING the investigation of ternary and quaternary high temperature systems formed by the transition elements of Groups IV, V and VI, the binary phase diagrams for these elements available in the literature were studied. In this study, the free energies of formation of the compounds formed in these binary systems were calculated; these values were then used to determine the general shape of the ternary and quaternary phase diagrams. Above 900°C, the transition elements of Groups IV, V, and VI are all bcc and form only Laves-type compounds in binary systems. The investigation was based on the binary phase diagrams published by Hansen.1 The Cr-Nb system was constructed from the data of Elyutin and Funke.' Several unpublished phase diagrams were taken from Schmidt'sLo and English'sl1 compilations. THE BINARY SYSTEMS valuations of the Thermodynamic Functions. Rostokers evaluated the boundaries of the (a + b) field in Ti-base alloys with a two-constant equation. The authors' interest is mainly in the center of the diagrams; therefore the miscibility gaps in the Zr-Nb, W-Cr, Ta-Zr, Ta-Hf, and Ti-W systems were used to evaluate the thermodynamic behavior of the binary systems. Lumsden's4 Equations 29.2, 32.1, and 33.1, page 287, were used for the excess integral free energy FeX, and for the excess partial free energies Fx and replaces b and b replacesP in Lumsden's notation):

Jan 1, 1962

[ ] Utilizing tendencies for low grade ores in the Sudbury District of Ontario to cave after higher grade ore has been mined, International Nickel Co., of Canada, Ltd., is recovering millions of tons of nickel-copper ore once regarded as submarginal. Inco is working lower grade ore than ever mined before from its underground operations because of the caving method and metallurgical practices. In the caving method, blocks containing as much as 1.5 million tons of ore are undercut. As ore from the undercut block is withdrawn, the block to be mined breaks away and starts to disintegrate as it moves downward. Inco is also using the blasthole method, using explosives to break slices of harder, tougher ore from solid material. Inco has built a new concentrator at one of its most recent shafts for handling the increased tonnages of low grade ore. The concentrator presently has a 10,000-ton per day capacity, and is scheduled to be increased to 12,000 tons. Hoisting from the mine is by push-button control and the ore is milled on the spot. A 7 ½ -mile pipeline carries bulk concentrate to reduction plants at Copper Cliff. Giant crushers, weighing 165 tons each, have been installed underground. Twenty-ton electric locomotives haul ore to the crushers. The expansion program is expected to lift total annual production of nickel in the free world to 375 million pounds annually, an increase of 150 million pounds. Inco is presently mining more than 1 million tons of ore per month from combined surface and underground operations.

Jan 1, 1952

By Arthur F. Johnson

Plant sites for the light metal industry must be located where ample low cost power is available. In the first half of the century hydroelectric development was the only source of this power-now the best sites have been exploited and those remaining do not promise enough water to permit year-round capacity power plant operation. In searching for economic plant sites engineers have concentrated on locations with vast water power potential. Olin Mathieson Chemical Corp. has been studying the economics of developing water power to make aluminum. However natural gas, lignite, and even atomic energy have also been considered as possible power sources for aluminum production. Economic studies have given consideration not merely to investment and production costs, but to total costs of delivering fabricated products to the market center of the U. S. When delivered costs are considered and when full account is taken of the newest techniques of mining bituminous coal and utilizing it to make electric power, one arrives at the inescapable conclusion that coal has emerged as the economic answer to American aluminum production.

Jan 4, 1955

By B. B. Zavoico

There were no radical changes in the petroleum situation in the Russian Soviet Union during the 1926 to 1927 operating year. The developments of the previous year were continued, but the major undertakings were far from being completed. The pipe lines from Baku to Batum and from Grozny to Touapse, and the large refineries on the Black Sea are delayed in their completion by the insufficient authorizations; until their completion the changes in the general situation will be necessarily of a halfway nature. The marketing situation was subject to much controversy during the past year and, though certain statements are quite true, the bulk of the criticism against the petroleum industry hardly deserves mention. The home market in Russia is steadily growing, with the per capita kerosene consumption already exceeding the prewar figure and fuel oil consumption obviously gaining. The foreign trade is making rapid and well-grounded success, but continues to suffer from low world quotations. There is no apparent sacrifice of home consumers in favor of export trade. The production of all Russian fields increased by 13,750,000 bbl. as compared with the 1925 to 1926 operating year, and next year's program anticipates a further increase of 9,720,000 bbl. (Table 1). The increased and improved refining facilities will make the real gain in production in the next year even larger than these figures indicate.

Jan 1, 1928

By G. Czupryna, S. Natansohn

Electrowinning is the prevalent technique for recovering silver from wastes generated in silver-tungsten electrical contact fabrication. Such scrap is placed in a permeable plastic basket, which constitutes the anode compartment, and is suspended in a larger cell where the cathode is mounted. A silver nitrate solution is used as the electrolyte and, upon application of an electric field, the silver migrates to the cathode where it deposits. At times, there is tungsten migration to the cathode compartment and consequent co-deposition with the silver. This W contamination, which may amount to several thousand mg/L (oz per gal), necessitates additional purification of the deposited Ag and its removal would, therefore, be advantageous. Eliminating the W impurity also extends the operating period of the cell with corresponding increases in the Ag output and savings in labor costs. The solution to this problem lies in the selective removal of the W from the AgNO3 electrolyte either by liquid-liquid or liquid-solid extraction. Although W extraction in the liquid-liquid mode with a quaternary amine or other reagents as extractants appears feasible, particularly in view of the low pH (about 1.5) of the system, this approach was not considered because it is essentially a batch-type process. It is a more elaborate industrial operation than extraction by ion exchange resins. Implementing the latter process consists of passing the electrolyte from the electrowinning cell through an ion exchange column which would extract the tungsten selectively and returning the tungsten-free stream to the cathode compartment. This process continues until the W extraction efficiency decreases (as a result of resin loading) below an acceptable value. The electrolyte is then directed through another, similar column while the W values are eluted off the first one and the resin is regenerated for another cycle. Thus, two columns in a parallel flow pattern provide the means for continuous processing of the electrolyte feedstock.

Jan 1, 1984

By Edward B. Dismukes, Walter R. Dickson

Measurements of current efficiency at an iron anode during the electrolysis of FeO-CaO-SiO2 melts contained in an iron crucible indicate that compositions of high SiO5 content conduct current almost entirely by ionic mechanisms. Hozueuer, compositions of high metal oxide content give euidence for considerable nonionic conduction that can be attributed to p-type semicon-duction. Measurements of transference numbers in a Hittorf-type cell show that both calcium and iron ions are important contributors to ionic conduction. ELECTROCHEMICAL properties such as conductance, transference numbers. and oxidation or reduction at an electrode have been studied as means of delineating the structure of simple silicate melts that are related to the more complex slags encountered ir steelmaking processes.' Measurement of these properties has strengthened the concept that molten silicates are constituted of metal ions and of silicate networks. Typically, the magnitude of electrical conductivity and the extent of agreement with Faraday's law have given evidence for ionic structures, and transference numbers have shown cations to be the exclusive carriers of electrical charge. However, melts containing oxides of iron, FeO in particular, have been found to exhibit nonionic conduction of curx,ent. The work by Inouye, Tomlinson, and chipman' demonstrated semiconduction, presumably of the p-type, in molten wüstite. Simnad, Derge, and George3 and Dukelow and Derge,4 in studying the electrolysis of FeO-SiO2 and FeO-MnO-SiO2 melts, concluded that p-type semi-conduction occurs in these systems, although ionic conduction is generally favored by increased percentages of MnO or SIO2. Previous research on the electrochemistry of

Jan 1, 1962