Search Documents

"Located on Missouri River 16 miles N. E. from Helena, 67 miles from Butte and 18 miles below Canyon Ferry. River drainage area 16,000 sq. miles.DAM: Built in 1907; rebuilt of concrete in 1911. Maximum height 129.3 ft., length over all 720 ft.; elevation of crest 3621; elevation of bridge 3640; normal head 60'; normal tail water elevation 3568.5.SPILLWAY: Length over all 491 ft.; clear opening in 24 sections; 445' flashboards, 14 high to elevation 3635, which is 3.5' above Canyon Ferry normal tail . water elevation.PENSTOCKS: 5 of steel, 12 ft. diam., about 75 ft. long from canal to main turbines, and 3 40-inch diam. from canal to exciters.WHEELS: 5 main pairs, horizontal, center discharge, 48-inch bronze turbines, 225 rev., 4,000 h-p. at 60 ft. head, made by S. Morgan Smith Co., direct coupled to generators, and--3 single, horizontal, 25-inch units, direct coupled to exciters.GENERATORS: 5 W. E. & M. Co. water wheel type, revolving field, 2,800 k-w., 2,400 v., 225 r. p. m., 3 phase, 60 cycle alternators.OPERATION: The plant has a larger water storage than Canyon Ferry and can also use stored water from Canyon Ferry storage. Separate transmission lines 13 miles long connect to lines from Canyon Ferry to Butte, and the Plant operates in parallel with the Canyon Ferry plant."

Jan 1, 1913

By James Norman

DIATOMACEOUS earth occurs in deposits widely distributed throughout the nation. The chief producing areas are in the Western States, where many high-grade deposits are known. Eastern deposits of diatomite are unsatisfactory for many purposes either because of impurity or because of the extremely fine particle size. Eastern users of diatomite, on the whole, must pay for transportation of the material from the west coast. The freight rate is necessarily high because of the great bulk of the diatomite. A satisfactory process of purifying the diatomaceous earths of Maryland and Virginia, which are unsuited for wide use only because of impurities, should be of value to eastern users. In the past, benefication of diatomite by wet processes has been limited to classification or sedimentation for the removal of sand from diatoms. Calcination with salt is used to produce a white diatomite when iron is present in the impurities, and small amounts of clay are rendered inactive in the process. No treatment has been developed whereby a large proportion of clay can be removed from a low-grade diatomaceous earth to give a diatomite of very high purity. In August 1937 the Federal Bureau of Mines, in cooperation with Dr. R. C. Williams, of Baltimore, undertook the problem of purifying low-grade Maryland diatomite by froth flotation. Work was done at the Eastern Experiment Station, College Park. Unless otherwise stated, the crude diatomite used was from the Patuxent River deposits near Dunkirk. This material, consisting of roughly one-third each of clay, quartz sand and diatoms, was representative of the usual low-grade marine diatomite found in the Coastal Plain Miocene beds of Maryland and Virginia and sporadically in other Atlantic coast states. As received, it contained 50 to 60 per cent moisture and probably had been wet since its formation.

Jan 1, 1940

By M. Gensamer

IN applied mechanics and in metallurgy the transition from elastic to inelastic action is a matter of considerable interest and importance. Often the first inelastic deformation is apparently quite homogeneous; that is, uniformly distributed throughout the specimen. Sometimes this deformation is heterogeneous; that is, localized; inelastic deformation proceeds to some definite amount in restricted regions before adjacent regions of the specimen are inclastically deformed. In such cases the deformation does not become homogeneous until the whole specimen has been deformed the amount corresponding to that for each localized deformation. If the test is stopped before uniform extension sets in, the heterogeneous character of the deformation is apparent on the surface of the specimen through characteristic markings, which have been called "Lüders"' lines, "Hartmann's" lines, the "Piobert effect," or simply "flow figures." These markings are the source of considerable trouble in fabricating operations, particularly in the deep drawing of steel sheet. In many cases where the transition is of this nature, the stress developed at the upper limit of the elastic range is greater than the stress during the period of heterogeneous deformation, giving rise to the familiar "drop of the beam" effect in testing. The amount of the yield-point elongation, as well as the value of the stress at the lower yield point (the value to which the stress drops when yielding begins), are functions of the tempera-ture and the testing speed. Lower temperatures and faster rates of testing increase both the yield-point elongation and the yield-point stress. These matters have been ably discussed in a recent paper by Winlock and Leiter1 though, as brought out by the discussion of that paper, the phenomena are but little understood. The purpose of the present paper is to clarify the problem through the application of a simple principle, and to show that, through the application of this principle, a number of phenomena in the plastic deformation of metals become more read-ily understood.

Jan 1, 1938

By Basil B. Zavoico

During 1937 the Russian oil industry made very satisfactory progress in its exploration branch and added considerably to its proven reserves in the older producing districts, while several entirely new potential areas were opened for development by discovery wildcats. The exploitation of known fields, however, suffered greatly from internal political difficulties, referred to as "sabotage," and was also seriously handicapped by the requirements for national defense under the duress of a grave international situation. More particularly, the necessity for preparing for a major war resulted during 1937 in short-rationing of the oil industry in its iron, steel and rubber requirements, affecting quantitatively drill pipe, casing, tubing and the rubber equipment of automobiles, and qualitatively much of the oil-field machinery for which it was either impossible or difficult to obtain iron or steel of required specifications, which necessitated manufacture of heavier and unwieldy equipment and caused directly and indirectly an unavoidable major curtailment of drilling operations below the planned footage. War-preparation measures during 1937 also required accumulation of a large gasoline reserve in the Vladivostok area and inasmuch as shipments from California can be made much more cheaply than from Caucasian refineries, either by tank cars across Siberia or by tankers via Suez Canal and Indian Ocean, some 2,000,000 bbl. of gasoline was imported from the United States in the past year, resulting in a decline of 46.98 per cent in net exports of all petroleum products from Russia below the 1936 net export volume, which is the lowest level since 1925. Production of crude oil during 1937 is estimated at 212,742,000 bbl. as compared with 202,543,700 bbl. produced in 1936, an increase of 5.04 per cent, but 11 per cent below the planned output. There were no major readjustments as to the source of crude-oil production, Baku district still accounting for the largest share; that, is, 77.21 per cent of the total. Exploration operations were outstandingly successful during the past year, major discoveries having been made on the Apsheron Peninsula, in Grozny and Maikop-Kuban districts, in Ural-Permian Basin, in Middle Volga-Samara district and other areas.

Jan 1, 1938

By Wilhelm Flesch

THE object of development work in the field of gasification is to find a process by which all' fuels, regardless of their individual properties, can be gasified economically. This paper describes the development of the Winkler process. The economy of the gasification process depends not only on the degree of the gasification effect but also, to a decisive extent, on the costs of fuel, production, and installations. Fig 1 shows the relation between fuel costs and gasification efficiency for various types of fuels. Since the fuel cost in the gasification of coke amounts to two thirds of the price of gas, and the thermal unit in brown coal costs only one third of what it costs in coke, it is easily seen how profitably cheap fuels can be gasified, especially if these fuels require minimum preparation and gasification is done in the vicinity of the mines. These possibilities were a great advantage of the Winkler generators, which were installed 20 years ago in the central German brown-coal fields and, at that time, were without rival for the gasification of finely divided fuels. In the Winkler generator (Fig 2), crushed and ground solid fuels were, for the first time, successfully gasified with oxygen and steam on an industrial scale. Unlike the usual processes formerly employed on an industrial scale, this gasification, which proceeds continuously in the glowing, seething fuel bed, makes only extremely low demands on the fuel. The fuel no longer has to be in lumps and abrasion-resistant, but must be capable of reaction and must be fed into the generator in a grain size of 0 to 8 mm. Brown coal or bituminous coal, or their low-temperature cokes, can be gasified in the Winkler generator. Large plants using fuels are operating on an industrial scale in Europe and in Japan. Table 1 shows the results obtained by gasifying these, fuels in Winkler generators. The thermal efficiency of gasification, which is the relation between the calorific value obtained in the gas produced and that of the fuel consumed, gives no indication of the quantity of steam generated in gasification. The generation of steam in the waste-heat boiler of the Winkler generator adequately-covers the steam consumed in gasification. To obtain effective gasification in the Winkler process, combustible mate-

Jan 1, 1953

By R. L. Powell, E. C. Houston, V. J. Jones

The phosphate ores mined in middle Tennessee typically consist of granular rock phosphate particles disseminated in a clayey matrix. In the TVA plant near Columbia, Tenn., the phosphate ore is mined, made into a slurry with the addition of a small amount of sodium hydroxide as dispersant, and treated in a hydroseparator to remove minus 10 micron material. The hydro-separator underflow, comprising a rough concentrate, is transported by pipeline to the plant; the hydro-separator overflow, comprising a tailing, is flocculated by addition of calcium sulphate and is discharged to settling ponds at a rate of about 1400 gpm. Sedimentation in the ponds produces a clarified efluent, which may be recycled for use as process water or discharged to surface drainage. This method of tailing treatment is not entirely satisfactory since poor sedimentation characteristics of the tailing result in poor ultimate utilization of pond storage volume. The sediment contains about 70 pct water, even after several years of settling, and is not sufficiently dry to permit it to be used as back-fill, which would provide a method for reclaiming ponds that had been filled with sediment. Since important advantages would result from a process whereby the water content of the tailing solids would be made substantially lower than that obtained in the present process, several possibilities of achiev- ing this were considered. Flocculation tests were made with a wide variety of chemicals, but none gave any improvement over the results obtained with calcium sulphate. Filtering or centrifuging was found to be infeasible. Small-scale tests of dewatering by electrophoresis showed promising results, so this method was studied further in pilot-plant equipment. It was found that the tailing could be dewatered by electrophoresis to produce the solids in a form suitable for use as back-fill. However, the de-watered tailing has no monetary value at present, and the process is not economically competitive with settling pond operation under present conditions. This paper describes the pilot-plant work on electrical dewatering. It is believed that the data may find application in dewatering physically similar but economically valuable materials such as clays or mill slimes, or in dewatering phosphate tailing in the event of increased settling pond costs

Jan 1, 1950

By W. M. Hirthe, E. H. Greener, D. R. McCann

It has been proposed1'2 that, at low temperatures, point defects are a strengthening factor in inter-metallic compounds whereas, at high temperatures, the deformation is diffusion-controlled and, therefore, an increase in the concentration of point defects tends to soften or increase the plasticity of a compound. More recent investigations, including those of Bloem and Kroger' on PbS, Kramers and smith4 on TiO, and Nadeau5 on LiF, have extended this concept to ionic crystals. Rutile (TiO2) is a tetragonal transition metal oxide which has a defect structure over at least the compositional range. The defect in near-stoichiometric rutile is either an oxygen ion vacancys or a titanium ion interstitial.' This investigation does not contribute to resolving the defect question but either defect would satisfy the results obtained. Six specimens having the same orientation, see Fig., 1, utilized in an independent investigation1' were cut with a diamond saw from a single-crystal boule purchased from the Linde Co. Three specimens were annealed in air at 1200°C for 4 hr and slowly cooled to room temperature in a period of 12 hr. The remaining specimens were reduced in a vacuum of l0 mm Hg at 1200°C for 4 hr and cooled at the same rate in vacuum. The reduced specimens were weighed before and after reduction and, assuming the weight loss to be oxygen, the corresponding oxygen-to-metal ratio is 1.998. All specimens were chemically polished and etched utilizing the techniques described by Hirthe, Adsit, and Brittain." The specimens were embedded in acrylic resin and mounted on a leveling vise in a Kentron micro-hardness tester. A 200-g load was applied to a Knoop indenter with a descent time of 18 sec and a dwell time of 20 sec. Eight indentations were made on a near (171) surface, approximately 3 deg from the (lii) plane, for each orientation of the major axis of the indenter relative to the crystal structure. The dependence of microhardness on orienta-

Jan 1, 1963

By L. D. Jaffe, John H. Hollomon

Fox many steel parts it is desired to obtain the maximum toughness consistent with the strength required by the mechanical design. It is generally recognized that the greatest toughness at any given strength is found in steels having a tempered martensitic structure,1 and is virtually independent of the composition of the steel2 (except for carbon). The choice of the composition of a steel for the parts in question should be based, therefore, on hardenability considerations and on manufacturing facility and economy. In a recent paper3 the concept of hardenability was discussed and a somewhat new approach to the problem was suggested. The hardenability was defined in terms of the cooling conditions (speed of cooling) required to avoid the pearlite and the bainite reactions. Since all the alloying elements do not have the same effects on the two reactions, the bainitic and pearlitic hardenabilities must be considered separately. In order to design a steel for a given part, it is necessary to design a composition that has both sufficient pearlitic and sufficient bainitic hardenability. However, this requirement does not fix the combination of alloying elements to be used; an infinite number of steels would have the required hardenabilities. Other considerations limit the choice. For example, decreasing the carbon content increases the toughness at a given hardness, and for this reason low-carbon steels are often desired. Limitations or requirements of refining, casting, or forming practices often affect the level of some of the alloying elements. Price considerations enter. Frequently, however, it is very desirable to minimize the tendency toward quench-cracking while maintaining the necessary hardenability. This paper is concerned with suggesting a method for choosing compositions that will have the required hardenability together with minimum tendency toward quench-cracking. QUENCH-CRACKING Since only the case in which the entire part will transform to martensite in the particular quench employed is being considered, the analysis of the quench-cracking problem is somewhat simplified. Quench-cracking arises from the temperature gradients existing throughout the piece during cooling. Because of these temperature gradients, the contraction arising from the decreasing temperature and the expansion arising from the austenite-martensite reaction do not occur uniformly over the parts, and stresses are set up that tend to cause cracking. The temperature gradients can be reduced by decreasing the severity of quench. This, however, requires that the hardenability be correspondingly increased by increasing the carbon or alloy content. An

Jan 1, 1946

By H. B. Small

The Ottawa river, the northeastern boundary of the Province of Ontario, and the dividing line between the latter and the Province of Quebec, has long been famous for the rafts of timber floated over its waters from the depths of the forest, and other poets besides Moore, have immortalized its beauties in verse. But with the ad vent of the railway which now pierces the forest solitudes, the days of rafting were numbered ; and the boat song is now heard no more on "Ottawa's tide," or at such long intervals only, that, when heard, it seems an echo of the past. The lumber trade is fast leav ing Ottawa City, the old headquarters of the business; and such square timber as is now cut is gradually finding other outlets than shipment to Great Britain, and other channels of transportation than the Ottawa river. Skirting the northern shore of this great river runs a vast chain of hills, assuming at times the altitude of mountains. Their geological character marks them as remnants of the earliest land of this conti nent. Following the course of the St. Lawrence from the Gulf of that name to the confluence of the river with the Ottawa, the course of which latter they then pursue, the range has been styled " the Lau rentians." Rolling in long undulations, with rounded, rather than rugged or pointed summits, they leave a margin of 8 or 10 miles, dipping in a gentle slope to the water's edge, rich for agricultural use, and dotted here and there with farms and settlements. Beyond this margin bold hills stretch northerly to blue mountains, rich in iron, lead, plumbago, and other minerals. The Apatite District.—One of these minerals is apatite, or phos phate of lime, the use of which as a material for the manufacture of superphosphate as a fertilizer has become the basis of the industry bidding Fair to prove ere long one of the chief elements of Canadian trade. So rapid has been the growth of this new industry that if the lumber business were to disappear from this mineral district, its void would be filled by that which has sprung up in connection with phosphate.

Jan 1, 1893

By E. Stansfield

IT. has long been known that coal is unstable and oxidizes in air, even at ordinary atmospheric temperatures; also, that such oxidation affects the analysis of coal. Nevertheless little or no precaution is taken to prevent oxidation in the ordinary methods of analysis, and the possibility of error due to oxidation is sometimes ignored even in researches on coal. Although the general nature of coal oxidation is well known, and many workers have made careful studies of the rate of oxidation of different types of coal exposed to oxygen at different temperatures, yet the amount of oxidation coals undergo in the ordinary process of analysis, and its influence on the determined analysis, is not well known, and the published data are widely scattered through the literature. This paper is a collec-tion, from this laboratory, of data that bear on the subject, together with a brief summary of three methods employed here to evaluate the oxidizabil-ity of coal. The post-Carboniferous coals of Alberta range all the way from anthracite down to lignite. As some of them are notably susceptible to oxidation, the necessity for care was early forced upon our attention, and oxidation has been reduced either by the removal of air with a vacuum pump or by the displacement of air with natural gas (methane). The two routine analytical operations most liable to involve oxidation are the preliminary, partial drying of the crushed coal (called air-drying) and the determination of moisture. The first is a prolonged operation on coarse coal at ordinary temperatures, and the second a short treatment on powdered coal at higher temperatures. Oxidation also occurs in coal samples stored in ordinary sample bottles. In order to gain information for this study, determinations were recently carried out on the same samples in air, in natural gas, and in vacuo. Sixteen coals were tested; three would be classed in the United States as coking bituminous coals, two as noncoking, nonslacking, bituminous coals, and the rest as subbituminous. Table 1 gives typical analyses of these coals as mined.

Jan 1, 1934

By R. E. H. Pomeroy

THE statistical data given in this paper are taken from the actual performance of the No. 2 reverberatory furnace of the Nevada Consolidated Copper Co., Me Gill, Nev., for a period of four months, from April to July, 1914. The principal furnace dimensions are: Length, 132 ft. ½ in. at the skim-line level; average width, 18 ft., 10 in. at the skim-line level. The roof is 7 ft. above the skim-line level at the firing end. The average area in the uptake flue is 36 sq. ft., and the area above the skim line under the vulcatory arch is 24.3 sq. ft. Fig. 1 shows a diagrammatic plan and sectional elevation of this furnace. The furnace is equipped with two 400-b.h.p. Stirling waste-heat boilers set in parallel. California crude petroleum is used for fuel and has a specific gravity of 16.5° B., flashing in open test at 199° F. The oil is heated to about 200° F. in a steam heater before going to the burners, requiring about 9 b.h.p. per furnace day to heat it from the line temperature to the burning temperature. Measurement is made by oil meter, checked daily by reservoir readings. The oil is fed by gravity (34 lb. static pressure) to seven low-pressure blast burners of the Steptoe type (Fig. 2). The blast for these burners is supplied at about 40-oz. pressure by a motor-driven Connersville blower of 42 cu. ft. capacity per revolution. The air supplied by the blower through the burners for atomizing the oil amounts to about 10 per cent. of the theoretical air necessary for complete combustion of the oil. The remainder of the necessary air enters the furnace through the burner openings in the firing wall. No checker holes are provided, and the charge holes in the roof are equipped with slide gates and "dog houses? to minimize air leakages. The combustion of the fuel, as shown by gas analysis at the front of the furnace, is practically complete, the carbon monoxide in the gases being less than 0.5 per cent.

Jan 2, 1915

By Grover R. Castle

INTRODUCTION Banks are being asked to assume more and more of the project risk in connection with project financings and, as a result, they are seeking to become more sophisticated in the way that they approach these kinds of financings. For example, a large number of banks that are active with the mining companies have established mining groups which typically will include mining engineers, economists, and bankers, in order to specialize their service to the mining industry. These banks have geared up these special service staffs so that they will be better equipped in their lending activities to analyze, measure and evaluate the project risk. The hope is that a team of these specialists will be able to predict the potential success or failure of these new "green fields" mining ventures that the banks are asked to finance. This paper shall focus on this subject and try to determine just how successful these specialists can hope to become as they analyze these various projects that are brought to them for financing. The approach that shall be taken in this paper shall be to examine how successful the mining companies themselves have been in the past with this same problem. These mining companies should be the most sophisticated in their approach to the analysis of the potential for success of a new mine because they have had the most experience in evaluating these projects. After all, who knows more about developing a mine than the companies that have developed similar mines in the past? For the purposes of this paper, the writer has selected a sample of 18 mines that have been developed over the years and measured the actual performance of each of these sample ventures against the original projections. All of these cases have involved the development of large projects where the sponsors or partners in the venture are substantial and sophisticated companies and where the feasibility studies have been prepared by engineering firms that are considered very professional in the industry or alternatively where the feasibility has been done by a comparable in-house staff. The sample cases have been chosen from a period which starts in 1965 and continues through 1981 with the cases distributed over that period as indicated below: [ ] Fourteen of the projects are open pit mines, three are underground mines and one mine starts on the surface and gradually goes underground. Seven of the mines are in the the far east with the remaining three in either South or Central America. The following four specific questions were examined for each project:

Jan 1, 1985

By R. B. Moffitt

INTRODUCTION In recent times the continuing depletion of high grade mineral deposits and the massive increase in raw material consumption have forced the metal mining industry to exploit ore bodies of lower and lower grades. To obtain a satisfactory financial return from these deposits, there has been the concurrent and evident trend towards increasing the size of operations to obtain benefits from the economies of scale. The evaluation, planning, and design of these large scale open-pit operations, so as to yield the maximum possible return on investment, is an extremely complex, iterative procedure. With profit margins trimmed, "small" errors can become much more significant and with exploration costs spiralling, accurate and rapid evaluation is essential. It demands a sophistication and precision in the evaluation process unheard of ten years ago. What follows attempts to describe the need to thoroughly plan the overall evaluation programme such that duplication of effort is avoided and all relevant information is systematically recorded from the outset of exploration. The final section of the paper takes a realistic case study to illustrate the significance of pit slope angles on the design of the final pit and the economics of the total project. THE EVALUATION PROGRAMME The team, (for a team effort it must be), that is charged with the responsibility of conducting the evaluation exercise, has the difficult task of placing values on a multitude of independent and inter-related variables. Each variable has some economic significance; the degree of significance varying according to the metal sought, the environment in which it occurs, the vagaries of the market place, to name but a few of the problems facing the project team. From this maze of variables, the team must identify those that have the most critical influence on the overall economics of the proposed venture. Investigations must then be set in motion to quantify these controlling factors more precisely. It is important to recognize that such investigations form part of the evaluation programme and require monitoring for both timing and cost as the whole exercise of evaluating the project continues. To add to the difficulties, the economic significance of any particular variable may change during the course of the programme.

Jan 1, 1972

By J. Morgan Clements

Petroleum has been known in Japan since at least 668 A. D., for a picture shows the presentation, during that year, to the Emperor Tenchi (Tenji) of "burning water" and ('burning earth" by his subjects from Echigo Province, which today is the largest producer of petroleum in Japan. The burning water was doubtless petroleum and the burning earth either bituminous shale or oil-soaked earth or rock from near the oil seepages. The early methods of getting the oil were simple and similar to methods used today in Japan and in China. Where the seepages occurred, trenches or shallow wells were dug along the seepages and allowed to fill with oil, which was then bailed out; in some cases, they filled with oil and water and overflowed. During the 300 years following 1500 A. D., the use of petroleum in Echigo Province seems to have increased considerably, as compared with earlier centuries, and records show that in 1818 the depth of the wells had been greatly increased. Doubtless, they passed through the seepages and tapped the shallow oil-bearing strata; probably some of these deeper wells were dug before that time. The real value of petroleum was not recognized until early in the Meiji era, which began in 1868, when the Japanese learned that the kerosene that was being imported was derived from petroleum. Guided solely by information obtained from books, they refined the oil and increased the depth of their wells in order to increase the production. The deepest well, dug by hand, about this time was 894 ft.' (273 m.) and by 1874 the recorded production reached 3499 barrels. In 1876, Benjamin Smith Lyman prepared geological maps of the Echigo oil field, which were the first of such geological maps made in Japan, and based on these a more enlightened development of the oil fields began; the Japanese, however, still dug the wells by hand. Toward the end of the '80s) an American well-drilling outfit was secured, but the efforts to use it failed from lack of experience by the operators. In 1888, a complete well-drilling outfit was purchased and American oil-well

Jan 1, 1923

By Robert D. Thomson

LISTED among strategic and critical minerals for stockpiling, mica is an important raw material in electronic and electrical equipment industries. Each year large quantities are consumed in the manufacture of television and radio tubes, radar sets, generators, transformers, electric toasters, and irons. Crude mica, which comes from the mine in crystals or in rough books of various shapes and sizes, is known as run-of-mine or book mica. Structural imperfections, impurities, rough edges, and defective laminae are removed by cobbing, rifting, and trimming to produce a marketable block mica or film mica.' After the rough books have been hand-cobbed to remove adhering rock, dirt, and crushed or defective mica they are rifted, or split. In the U.S. a straight-bladed knife is generally used for rifting. Products of this operation are classed broadly as untrimmed sheet mica and scrap. Sheet mica is any relatively flat piece sufficiently free from physical defects to be cut or stamped into specified shapes for industrial use. Sheet mica is classed as block, film, and splittings. Block mica is not less than 0.007 in. thick with a minimum usable area of 1 sq in. Film mica is split from the better qualities of block mica to groups of specified thickness ranging from 0.0012 to 0.004 in. Splittings are sheets with maximum thickness of 0.0012 in. and minimum usable area of 3/4 sq in. As virtually no mica splittings are produced in the U.S., they will not be discussed in this report. Small, low quality block is subdivided as punch and washer. Punch mica is thumb-trimmed material large enough to yield a circular disk of at least 11/2 in. diam for stained quality mica and 1 1/4 to 2 in. for clear quality. Poorer lots, often referred to as washer mica, are also included in the general term punch mica. Trimming, the next step in processing sheet mica, removes broken and ragged edges, loose scales, and other major imperfections. Trimming may be done with a knife, sickle, shears, or fingers. In the U.S. it is usually done with a 3-in. linoleum knife to obtain a bevel-edged cut. If ragged edges are broken off with the thumb and fingers, the mica is called thumb-trimmed. Full-trimmed is rifted mica trimmed on all sides with all cracks, reeves, and

Jan 1, 1957

By C. R. Fischrupp, M. D. Helfrick, W. A. Straw

In the manufacture of telephone apparatus a number of nonferrous sheet metals arc blanked and formed to produce a wide variety of parts, which are generally small in size because of space and weight requirements. Many are given sharp bends in forming, so that they may be assembled into compact units. This study covered sheet metal of the alloys of brass, phosphor bronze and nickel silver that are most extensively used by our company. In general, the sheets range from 0.005 to 0.100 in. in thickness and from 1/4 hard to extra spring temper in hardness. As many parts function as flat springs, and others require the maximum stiffness for structural reasons, a large percentage of the metal is used in the hard and spring tempers. So, because of the necessity for the minimum radius of bend consistent with the maximum in hardness, there has been a need for information as to the forming characteristics of these sheet metals in the various alloys, tempers and thicknesses. The literature yields relatively little regarding such forming characteristics, so that designers of apparatus and tools have been largely dependent upon past experience or tool tryouts for guidance. In presenting tabular data intended as a basis for selecting the temper of the metal and radius of the bend, we recognize the influence of many other factors which are not covered in this study. For example, the angle of the bend and conditions of the metal, such as grain size and presence of impurities, as well as conditions of the fabricating process, such as rate of forming and adjustment of the tools, may all affect the result. In addition, a bumping operation subsequent to forming, which is frequently used to set the bend, increases the strain on the metal. We wish to emphasize the fact that this is not considered a scientific investigation of the formability of materials or an attempt to correlate forming characteristics with various other properties of the metals, except in so far as such properties are controlled by commercial limits on composition and temper. It is expected, however, that the data presented may serve some useful purpose in estimating the relative formability of different thicknesses

Jan 1, 1931

By Charles Mitke

THE United Verde Extension mine is located in the Jerome mining district, on the eastern slope of the Black Hills, approximately northeast of the town 'of Jerome, Yavapai County, Arizona. The ore deposit may be termed a replacement in Yavapai schist. This schist is one of the oldest formations in the district, being probably of volcanic origin, and has been folded and faulted and contains intrusions of diorite and quartz porphyry. It is believed that the mineralization followed the porphyry intrusions and replaced the country rock; this was followed by erosion and a period of secondary enrichment, all completed in pre-Cambrian time. Later sediments of sandstones and limestones, to the depth of approximately 600 ft. (182 m.), were laid down, followed by volcanic flows. Faulting and erosion again took place, resulting in the present complicated arrangement of the strata. Prospecting, therefore, is very difficult, because the sediments practically cover the mineralized areas. This necessitates the sinking of deep shafts, cross-cutting, and, in some instances, diamond drilling to learn something of the various relations of the different formations and the occurrences of intrusions associated with ore deposition. The locating of new orebodies, therefore, is beset with innumerable difficulties. EARLY MINING METHODS The two orebodies constituting the principal resources of the company are known as the- small orebody and the Bonanza, or large orebody. These are about 150 ft. (45 m.) apart, and while they appear to be distinct orebodies may later prove to be connected. The character of the ore, the general associations of the porphyries adjoining the orebodies, and other characteristics, both in the ore-and general environment, are very similar. The small orebody was the first to be discovered and was mined for some time before the Bonanza was found.

Jan 1, 1919

By T&apos Ke, ing-sui

THE subject of recrystallization and grain growth has been much studied and the literature on this subject is numerous. Such studies have been mostly carried out by metallographic examination of X ray methods. Since recrystallization and grain growth involve elementary atomic processes, their mechanism can best be elucidated by a study of some properties which can be readily traced back in terms of such atomic processes. Prior to a detailed quantitative study, however, it is necessary to explore first the possibility and practicability of utilizing any particular property for obtaining the desired information. We have pointed out in a preceding article' that the internal friction of cold-worked metals is extremely high during recrystallization and it drops abru~tlv once the recrystallization is complete. ~reviois work has also shown that the viscosity of grain boundaries in a recrystallized specimen at a given temperature is raised by grain growth.' It seems thus that the measurements of internal friction may furnish a useful tool for the study of the mechanism of recrystallization and grain growth in terms of elementary atomic processes. The purpose of this paper is to report results of a study along this line. We will demonstrate that the internal friction method does give results in agreement with those furnished by conventional metallographic examinations. Once such a correlation has been established, we will be in a position to take further steps to achieve new information which cannot be achieved by conventional methods. The measurements of internal friction were made using apparatus and procedures similar to those used in the preceding article. All the measurements were made under such a small stress level that the internal friction is independent of stress level. The frequency of vibration is, unless mentioned otherwise, about one cycle per second in all cases. Internal Friction and Recrystallization Complete Recrystallization Temperature: Fig. 1 shows the internal friction curve during annealing of a few metals: aluminum, alpha brass and iron. These curves were determined in the following manner. In the curve for aluminum, internal friction measurements were performed upon. 99.991 aluminum subjected to 95 pct reduction area. The internal friction was first measured at room temperature. The specimen was then annealed at 50°C

Jan 1, 1951

By Harold C. Price

Prior to Sept. 1, 1928, there had never been constructed what might be termed a long pipe line with electric-welded field joints. A year later more than 2500 miles of electric-welded lines had been completed which varied in diameter from 6 to 20 in., and in length from 50 to 700 miles. This paper discusses methods used on five lines with a total length of about 750 miles. The welding equipment used for the firing line or rolling welds, was 300-amp. generators driven with six-cylinder gasoline engines, and for the bell-hole or tie-in welds, 200-amp. generators driven by four-cylinder gasoline engines. A welding gang consisted of a foreman, 6 to 12 firing-line welders and 2 to 4 bell-hole welders, a mechanic and a tractor driver. Coupons about 1/4 in. thick were frequently cut from completed welds, which showed a cross-section of the weld and an indication of its size and penetration. For tests of tensile strength complete welds were cut out. The tensile strength of 52 welds cut from 420 miles of 12-in. line averaged 50,870 Ib. per square inch. The following results give a fair average of the number of welds made per man per day: on 157 miles of 8-in. line both firing-line and hell-hole welds averaged 15.3—the firing-line average was 21; on 39 miles of 10-in. line the firing-line average was 19.9; on 50 miles of 6-in. line, with unfavorable weather, the average was 17.7; on 424 miles of 12-in. line most of which was welded during the spring, 10.3, and with good weather the average rose to 13 welds per day. The average time for making a complete weld on 12-in. pipe 0.313 in. thick was found to be 30 min. for the rolling weld and 45 min. for tie-in welds. A comparison of costs between electric and gas welding shows that the cost of labor for electric welding is 25 per cent. more than gas, generating cost 61 per cent. less than gas, welding wire 40 per cent. less than gas, and supervision and overhead the same. Estimating 50 per cent, annual depreciation on electric welding equipment, and no depreciation

Jan 1, 1930

By R. C. Palmer

The testing of flotation oils has occupied a large part of the time of the testing departments of various companies using the flotation process in the beneficiation of their ores. The great differences in ores and in oils has made such work necessary, as it has not been possible to select the oil best suited for the purpose without trial of many kinds. In fact, individual shipments of flotation oils from the same manufacturer will often differ so radically that the mill men have been forced to test every lot of flotation oil before its use in the mills. Further, although almost every imaginable product of the distillation of wood, from alcohol to pitch, has been tested in a more or less perfunctory manner by various people, few companies have allowed the results of their tests to be made public. This work was undertaken for the purpose of obtaining reliable data regarding the value as flotation agents of a number of products that are obtained from the distillation of wood by different methods, and incidentally to determine whether some of the products not used at present could be used. Large quantities of such materials are being masted or burned in the wood-distillation plants of the United States, and if some use other than fuel could be found for these materials, such a use would represent a distinct saving to the country as a whole, would increase the profit of wood-distilling plants now operating and perhaps make it possible for others to operate which at present cannot do so except at a loss. At the same time it was thought that if such products can be used as flotation agents, then their use would serve to increase the number of oils and other products available for flotation purposes. It was also hoped that it might be possible to discover a substitute for some of the most effective but comparatively high-priced oils which are now used for flotation

Jan 1, 1917