Search Documents

By N. I. Fisher, J. Shepherd

Statistical studies have been carried out on structural geological data collected across a large zone of roof failure 600 m (1968 ft) wide and at least 800 m (2642 ft) long in the Greta coal seam at Aberdare East Colliery. Two swarms of hundreds of minor, normal faults with throws commonly between 3 and 300 mm in the room and pillar workings are broadly coincident with roof failure. The faults have been classified into dip slip and oblique and strike slip types. Roof conditions have been classified into good; troublesome with subclasses scaly, heavy, gutter falls and wide, flat-roofed falls; and severely failed with subclasses very heavy roof, gutter falls and dome falls. Troublesome conditions are defined as those in which the height of the fall is less than or equal to 0.3 m, and severely failed conditions as those in which the fall height is greater than 0.3 m. Comparison of faults, roof condition and mining rate on a shift basis indicates that faults and roof failure are much more important than machine breakdowns in reducing mining rate. The effect of faults on roof conditions has been quantified using a concept called the "zone of influence," a rectangular area around a fault in which the fault has potentially deleterious effects. The spatial comparison of fault "zones of influence" with areas of roof failure wing Spearman's rank correlation coefficient shows that, while normal dip slip faults do not appear to be associated with roof failure, oblique slip and strike slip faults appear to be associated with roof classed as severely failed. The "zone of influence" of an oblique slip fault may extend up to 3 m on each side of it in the headings and up to 1.14 m in the cut-throughs. The fault "zone of influence" has geomechanical implications for the design of mine openings and Possibly represents the maximum length of a cantilevered roof beam likely to fail during mining, owing to a fault. Roof conditions could Possibly be predicted in blocks of &gin coal if the type of fault could be identified in oriented drill cores.

Jan 1, 1979

By Louis A. Carapella, William E. Shaw

MAGNESIUM and its alloys have long been characterized as possessing limited capacity for mechanical forming at atmospheric temperatures prior to rupturing despite their outstanding performances in this respect at elevated temperatures. Responsible for this behavior are the fundamental facts that these hexagonal-type metals have comparatively few slip elements at low temperatures for any extensive deformation and that, at high temperatures, additional slip elements become operative, thus enhancing greater plasticity under strain. The transitional point has been set at 225°C by Schmid1 for single crystals, and at 250°°C by Morell and Hanawalt2 for extruded magnesium metal. In a recent X-ray investigation on polycrystalline magnesium-alloy sheets, Barrett and Haller3 have revealed that, below the transitional temperature, the initial plastic deformation proceeds mostly by a twinning action; that, above such a temperature, the action is mostly by slip. The deep-drawing performance of the magnesium + 1.5 pct alloy sheett over a wide range of temperatures has been investigated by Weber and Vanden Berg,' and their results are presented in Fig r. It should be noted from this work that a maximum drawability of about 25 pct at room temperature has been obtained on this alloy under the conventional deep-drawing operations. For the same alloy, it is now possible to augment the cold drawability to about 40 pct by a process to be disclosed. Hitherto, this value has been obtained only by deep-drawing the alloy at around 230°C. That greater plastic flow is attainable at atmospheric temperatures on magnesium under certain deformational techniques was discovered by the authors6 in their analyses of plastic-deformational behaviors of pure magnesium. This fact is best illustrated in Fig 2 from the Hargreaves analysis6 performed by the authors under two different modes of loading. For direct test, a separate unstrained specimen was used for each load duration, whereas for the integrated test the same specimen was employed for all the five intermittent loadings so that the load duration was made additive throughout the investigation. The higher plastic flow-rate at room temperature, as designated by the Hargreaves constant S, was obtained by the integrated or intermittent loading procedure. The authors5 in further tests showed that, under such a procedure greater plastic flow was also realized with a progressive increase in deformational loads. These findings have been applied

Jan 1, 1947

By G. J. Wilson

Review of difficulties experienced in drilling directional wells in the offshore Grand Isle Block 43 field showed most failures of drill pipe, drill collars and casing to have been associated with excessive dog-legs. Alleviation of difficulties was approached by synthesizing theoretical and practical concepts in a planned dog-leg control program. Preventive measures necessary to control dog-leg severity and corrective measures used to reduce unacceptable doglegs are discussed. When other measures fail, deliberative measures as outlined can be employed after the probable cumulative fatigue damage to be sustained by the drill pipe has been determined. Results of a program successful in virtually eliminating problems stemming from excessive dog-legs indicate that control of dog-leg severity in directional wells is feasible and will cause no decrease in the over-all drilling rate. INTRODUCTION Prompted by an increasing frequency of drill pipe, drill collar and casing failures, a study of 50 directional wells representing 592,000 ft of hole, including 444,000 ft of deviated hole, drilled in the offshore Grand Isle Block 43 field was conducted in early 1965. A number of drill pipe washouts and six keyseating problems were recorded and a detailed review was made of 16 failures which had required fishing effort in 10 of the 50 directional wells drilled prior to June, 1965. These problem wells are exemplified by Wells G and F for which pertinent data are shown in Figs. 1 and 2. Data pertaining to all of the 16 failures are summarized in Table 1. Inspection of these data shows most of the problems to have been associated with dog-legs in excess of theoretical limits suggested by Lubinski' and excessive dog-legging is indicated to have been concomitant with whipstocking in several of the problem wells. Results of the investigation agreed with those reported by Schenck2 who had concluded that problems could be expected when dog-leg severity exceeded limits proposed by Lubinski. Since Schenck had demonstrated the desirability and feasibility of drilling directional wells without excessive dog-legging, a dog-leg control program was established in June, 1965 for wells drilled in the Grand Isle Block 43 field. This paper reviews the methods by which theoretical and practical concepts were synthesized to develop a program of preventive, corrective and deliberative measures which virtually eliminated problems stemming from excessive dog-legs in directional wells. Dog-legs of a magnitude causing no damage are referred to as permissible +1CONTINENTAL OIL CO. HARVEY, LA.

By R. A. Bergman, C. J. B. Fincham

THERMODYNAMIC properties of many high-temperature systems containing sulfur, such as slags, metal sulfides, and solutions of sulfur in liquid metals, have been studied by means of equilibration with known gas mixtures.'" This method presupposes a complete and accurate knowledge of the thermodynamic data for all possible components of the gas phase at high temperatures. However, a survey of the data available up to 1952 on the thermodynamics of gaseous sulfur species and compounds, by Richardson and Jeffes,' showed that there was considerable uncertainty in the values of the free energies of formation of S, SO, HS, and CS. In many cases, this uncertainty made it impossible to decide whether or not these species would form a significant proportion of the sulfur present in the gas phase in any given system. After the review by Richardson and Jeffes had been published, St. Pierre and Chipman6 measured, by an indirect method, the free energy of formation of SO. This also enabled a clear choice to be made among the three possible spectroscopic values for the dissociation energy of S2 into atoms10 thereby determining the free energy of formation of S from S2, and fixing the free energy of formation of HS more accurately" The main purpose of the present investigation was to measure the free energy of formation of CS, which was still in considerable doubt. For example, at 1600°C, it could be estimated to be +6 +25 kcal per mole,* most of the uncertainty being in the * Based on the dissociation energles of CS6 and S2,5 the heat of sublimation of graphite, and, the assumption that the entropy of formation of CS is the same as that of CO. value of the dissociation energy." A secondary purpose of the investigation was to determine more accurately the equilibrium sulfur pressures over dilute solutions of sulfur in carbon-saturated liquid iron. General Method Dilute solutions of sulfur in liquid iron, saturated with carbon, were brought to equilibrium at 1600" and 1800°C, with known gas mixtures consisting, initially, of A and CS2. After equilibrium had been reached, the melts were quenched and analyzed for sulfur. In the high temperature region of the furnace, an equilibrium was set up between the various possible sulfur species and compounds in the gas phase; namely, CS2, CS, S2, and S. (It can be calculated that the amounts of S6 and S, are negligible at these temperatures:) Morris and Bueh17 and Kitchener, Bockris, and Libermana had previously studied the corresponding

Jan 1, 1958

By Walter C. Smith

THE Cerro de Pasco Copper Corp. began to produce bismuth at the Oroya smelter in 1929, at which time the only important consumption of that metal was in the manufacture, of pharmaceutical compounds, and the normal supply of metal exceeded the demand. With a new and major producer entering the field, additional uses for bismuth had to be developed. A survey indicated that the most promising opportunity lay in fusible alloys containing bismuth. A large number of bismuth alloys were known and a few of them were being used in the manufacture of automatic sprinkler heads and safety plugs. The literature cover in,- the- alloys was found to be sketchy and contradictory. Research, development, and educational work carrried on by the Corporation during the past fifteen years has resulted in greatly enlarged uses for the metal. In general the low-melting bismuth alloys are of high specific gravity, relatively soft, of low tensile strength, brittle to shock, yet subject to plastic

Jan 1, 1945

By C. W. Burrows

The burden a man can endure depends on its magnitude and the number of times it is applied, as well as on many other factors. The resisting power of steel likewise is dependent on many factors. The maximum load it can support indefinitely is much less than its possible momentary burden. A light load straining the metal far within its elastic limit, if repeated indefinitely, ruptures the metal. The magnitude of the stresses that may be alternately applied and removed without rupturing the material depends on the number of repetitions of the cycle; the intervening periods of rest; the thermal, electric, and magnetic conditions, as well as the presence of secondary streessses. While we are unable to formulate the law between the magnitude of repeated stresses necessary to produce rupture and the length of time during which these alternating stresses may be applied before rupture, my experience is that the time increases as the magnitude of the force decreases, according to a law which! to a first approximation, is exponential. In other words, F = Ce-t where F= magnitude of alternating stresses; t= time for which stresses are continued; C = constant, which depends on the conditions under which the operations are carried out. It is quite probable that the same type of law holds for the magnitude of a continuous force and its duration. When a rod of steel is subjected to the blows of a drilling hammer several things happen. First, one end is struck by the hammer and the other end is driven into the rock, thus causing a bodily displacement of the entire material of the steel drill. The greatest stresses involved in this bodily displacement are located at the two ends of the steel and manifest themselves by the distortion of these parts. Second, after the blow has been delivered, the steel drill, due partly to its own resiliency and partly to the resiliency of the rock, experiences a vibratory motion as a whole, this motion is quite similar to the bouncing of a rubber ball thrown violently upon a smooth pavement. Third, the free vibration of the drill is determined only by its own natural period of vibration. This motion involves all the characteristics of any vibrating body emitting sound. Certain elements of the rod will experience alternations of condensation and rarefaction and, in these regions, the individual steel

Jan 1, 1922

By T. L. Berger, M. C. lnman, M. F. Rose

AFTER shock loading, mechanical twinning has been observed by several authors1-4 for a variety of fcc metals and alloys. It has been shown2,3 that low stacking fault energy materials deform primarily by the formation of mechanical twins and stacking faults during dynamic loading. Further, Inman, Murr, and Rose2 have shown that a correlation exists between the average hardness and the volume percent of mechanically twinned material in stainless steel. It has been observed in nickel' that mechanical twins are produced during shock deformation if the peak pressure associated with the shock wave is greater than 350kbar. It is the purpose of this work to discuss shock-hardening mechanisms in nickel and to determine to what extent the initial condition influences the final response. The "flying plate technique" was used to generate planar shock waves with peak pressures as high as 710 kbar. The details of the technique5" have been discussed elsewhere and will not be repeated here. The material used in this study was polycrystalline nickel of 99.98 pct purity and had an initial grain size of 0.18 mm. Prior to any deformation, all samples were given a stress-relief anneal of 6 hr at 600°C in a vacuum furnace. After annealing, the initial condition of the samples was changed by cold rolling individual samples from 0 pct to a maximum of 80 pct reduction in thickness. This provided samples with controlled initial histories for shock deformation. Immediately after shock loading, the specimens were slowed and quenched by suitable arrangement of buffer material and water bath. This technique minimized specimen damage and the effects of shock heating on the samples. Since deformation twins in high stacking fault energy fcc metals are only produced at high stress levels, the initial defect configuration prior to mechanical twinning should greatly influence the number of twins formed. In fact, Zukas and Fowler7 have found that prestraining in iron and steel greatly suppresses the formation of mechanical twins during the shock deformation process. Following the methods of Warren and warekois8 and Cohen and Wagner,9 X-ray diffraction profile analysis was performed to determine the incidence of stacking faults and mechanical twins in the deformed nickel. Analysis was made on samples in the annealed, cold-rolled, shock-loaded, and cold-rolled—shock-loaded states. The estimated accuracy of the peak position measurements is *0.01 deg in 2?. Therefore the accuracy in the measurement of the relative peak shifts between the (400) and (222) diffraction line profiles is on the order of *0.04 deg in 2?. None of our measurements indicated peak shifts greater than 0.04 in 28. This would correspond to a fault density of -1 pct and sets the limit on the sensitivity of our instrument. Similarly, analysis of the shift in the center of gravity of the diffraction line profiles yields the minimum measurable value of the twin fault probabilitya to be -0.002. Fig. 1 shows mechanical twinning in nickel shock-loaded to 400 kbar. In this photograph, fault intersections are clearly visible. The thickness of the individual fault lamellae was determined from the image widths of their lines of intersections by the

Jan 1, 1968

By R. E. Caffrey, S. K. Tung

This paper reports some of tile results obtained from the vapor-phase reaction of a volatile metal halide with a hydrogen and carbon dioxide mixture in an epitaxial-deposition chamber. Tile oxides deposited were silicon di oxide, aluminum oxide, mix-12tves of silicon di oxide and aluminum oxide, and titanium oxide. Tile deposited silicon di oxide was transparent and amorphous and had a density and index of refraction similar to that of thermally grown silica. The vote of etching was determined. The thickness uniformily of the oxide was found to he related to the aerodynamics of the system employed for deposition. A clear silicon di oxide layer was found to be dependent upon the quality of the surface prior- to aside deposition. The process parameters affecting the vale 0f deposition were studied. The deposited aluminum oxide was transparent, holy-cl-ysttrlliile, and possessed remarkable resistance to hydrofluoric acids. By measurements it has been shown that the deposited aluminum oxide is both insulating and continuous. ThE cleanness of an epitaxial silicon surface both immediately after growth and during device processing is thought to be one of the major factors contributing to the electrical properties of a final device. The advantage of protecting an epitaxial silicon wafer surface with an oxide grown immediately following epitaxial deposition is obvious. The successive growth of silicon and silicon diox- ide in epitaxial apparatus was studied by Steinmaier and loem.' They formed silicon dioxide films on a silicon substrate by adding water vapor to the silicon tetrachloride-hydrogen mixture in an epitaxial system. They also showed that, when a gaseous mixture of carbon dioxide and hydrogen is injected, water is formed only at elevated temperatures. Thus the reaction of water vapor and silicon tetra-: chloride will be limited to a relatively small reaction zone near the substrate. This paper reports some results of oxide films obtained from a vapor-phase reaction of a volatile metal halide with a hydrogen and carbon dioxide mixture in an epitaxial-deposition chamber. EXPERIMENTAL APPARATUS The system employed for the oxide deposition is a modification of a vertical system used to produce high-resistivity silicon layers by the hydrogen reduction of silicon tetrachloride.' The modification shown schematically in Fig. 1 consisted of an additional carbon dioxide gas stream which entered the reaction chamber with a hydrogen stream saturated with metal halide vapor and a diluting hydrogen stream. Silicon dioxide layers made from a mixture of silicon tetrachloride, hydrogen, and carbon dioxide gases will be discussed first. EXPERIMENTAL RESULTS 1) Factors Affecting the Rate of Oxidation. An epitaxial silicon layer was deposited by the hydrogen reduction of silicon tetrachloride on an n-type,

Jan 1, 1965

By Earl G. Alexander, W. R. Runyan

The nature of silicon growths which form on amorphous silicon dioxide during epitaxial deposition in unmasked areas was investigated. Octahedral silicon crystals nucleate and grow on the oxide at pinholes, adjacent to foreign matter, and probably at oxygen-deficient sites. Generation of these oxygen-deficient sites on the oxide surface is shown to be thermody-namically favorable under usual deposition conditions. The conditions which affect saturation (SiCl4 concentration, flow rate, temperature) determine the number of sites on which silicon will nucleate and grow. Reaction product HCl is likely responsible for suppressing silicon growths on the oxide near exposed areas of silicon. Evidence is given that the oxide-silicon interaction occurs in hydrogen only and involves water as a transport agent. SINCE shortly after the first epitaxial layers of silicon and germanium were grown over large areas, efforts have been underway to grow selectively on specified portions of the surface. Such selective growth should be particularly applicable to monolithic integrated circuits. Usually the approach has been to use a mask to delineate the desired area,'-7 but the VLS methoda can also be used, and direct programmed atomic beam deposition has been suggested.9 The masking techniques may embody two forms: in one the mask is a material which can later be removed along with any growths attached to it; in the other, attempts are made to prevent growth on the mask, so that over a whole slice the only deposition that will occur is in the unmasked regions. The present work is concerned with only the latter case, and specifically with silicon. Joyce and Baldrey1 suggested the use of thermally grown silicon dioxide as a mask material and showed that for the proper choice of operating conditions (total flow, SiCl4 concentration, total deposition time, and temperature) spurious growth could be minimized and that if the deposition times were not too large, and the criteria not too stringent, a usable process occurred. Later Schnable et al 4 observed that after extended deposition times, during which most of the silicon dioxide became covered with growth, there was always a band of oxide around the exposed silicon area that was quite free of spurious silicon crystallites. This latter observation is particularly intriguing since it extends the hope that with proper precautions masking can be much more versatile than it presently is. EXPERIMENTAL PROCEDURE Silicon substrates oriented to within 1.5 deg of a (111) plane were prepared by etch polishing lapped

Jan 1, 1967

By J. L. Rodda

The desirability of a uniformly sized abrasive for metallographic polishing has probably been recognized in a general way for a long time. Certainly all metallographers have recognized the damage that can be done to a polished surface by a piece of grit, especially if one of the softer metals, such as zinc or aluminum, is being polished. It is to be doubted, however, whether many metallographers have had any adequate idea of the particle size of the abrasives they were using or of the range of sizes encountered in any given grade of abrasive. At any rate, the descriptions of abrasives for metallographic work found in the literature are generally very meager. It was with the idea of securing an abrasive with a limited range of particle size that a study of this problem was commenced. Commercial abrasives, even when recommended for metallographic work, are made up of particles of varying sizes. One such abrasive contains some particles so fine that they remain in suspension for days and other particles so coarse that they settle at the rate of 3 in. per minute. It is evident that the coarsest particles are over 100 times the diameter of the smallest ones, or over 1,000,000 times the volume. The hopelessness of avoiding scratches under these conditions is evident. Vanderwiltl has described a laboratory method for grading abrasives in which the elutriator is used. Le Chatelier's method, described by Goereq2 also makes use of an elutriator. However, the elutriator is too slow for this purpose and requires too delicate a control for the range of sizes desired. The method of stirring up the abrasive in water, allowing it to settle for a given time, then drawing a measured depth off the top of the suspension, has been finally adopted as the simplest procedure. The largest particle in a given portion is then determined by Stokes' law:3

Jan 1, 1932

By D. Perry, G. W. Binkley, G. K. Dumbauld, F. A. Brooks

A new cementing technique has been developed which is particularly applicable to permanent-type well completion operations. The technique makes use of the accelerating effect of calcium chloride on setting time and strength development of cement cake deposited in squeeze cementing. An unique feature is that the accelerator is applied after the unaccelera-ted cement slurry has been squeezed and the excess has been reversed from the well. Laboratory data on the accelerating effect of calcium chloride applied to the fi1ter cakes of three low-water-loss cementing compositions demorzstrate that the procedure results in relatively rapid development of strength and impermeability of the cement cake. Simulated squeeze-ceinenting tests made in the laboratory likewise corroborated the practicality of the procedure. The laboratory tests showed that a newly developed oil-emulsion cemerzting composition is more susceptible to acceleration of set than are modified cements containing high percentages of bentonite. The acceleration procedure has been used successfully in field operations. INTRODUCTION Nature of Problem In squeeze-cementing operations, a substantial amount of time is consumed in waiting on the cement to develop strength after it has been squeezed into the well. Frequently, an interval of 18 to 24 hours or longer is required for the development of strength sufficient to prevent failure of the cement during subsequent operations in the well. Reduction of this waiting-on-cement time offers appreciable savings both in time and in money. A particular type of squeeze-cementing operation to which an increasing amount of attention has been given is encountered in permanent-type well completion operations wherein perforations are to be squeezed off1. In this procedure, it is customary to pump the cement slurry down the tubing and out into the perforated section through a retractable extension pipe. Squeeze pressure is then applied, which forces the cement slurry into the perforations and causes the build up of a compact filter cake of cement within the perforations. The excess slurry remaining in the hole is then removed by reverse circulation. The extension pipe is then retracted, and, if a new interval is to be perforated, a perforating gun is run through the tubing. The newly perforated interval may then be tested by swabbing. In such operations, it has been customary to allow approximately 20 hours or so for hardening of the cement squeezed into the perforations. This time interval is usually measured from the time that the cement is reversed out of the hole to the time that subsequent swabbing is started. If the cement has not developed strength at the commencement of swabbing, the pressure differential caused by swabbing results in failure of the squeeze job. At the time that the work described in this report was initiated, particular consideration was given to the reduction of waiting-on-cement time in squeeze cementing by the permanent-type completion technique. Consequently, much of the experimental work was directed to this specific objective, though the process which was developed for acceleration of strength development has possible application in other than permanent-type completion operations. Method of Attack Although quick-setting cements

Jan 1, 1957

By John P. Huger

me phase diagram for the system Ag-Si has been established by thermal analysis. The diagram is a simple eutectic type with a eutectic at 3.0 pct Si and 840°C. From the liquidus curve and with the aid of regular solution theory, the thermodynamic properties of the liquid Ag-Si system at 1420 °C have been determined. Silicon exhibits positive deviations from Raoultain behavior at all compositions, while silver exhibits both positive and negative deviations. MEASUREMENTS of silicon activities in liquid iron alloys by means of distribution studies between the immiscible liquids silver and iron have been reported by Chipman, Fulton, Gokcen, and caskey.' The applicability of this technique is dependent, however, on the accuracy of the silicon activity values in the Ag-Si alloys, particularly in the dilute silicon region. Darken and Gurry2 have shown that log ?si/(1-xSi)2 is approximately linear with composition, but uncertainty exists in the extrapolation to dilute solutions. Their calculations are based on the old Ag-Si phase diagram of Arrivaut3 and any variation in the position of the liquidus curves will strongly influence the extrapolation. The purpose of this study is to redetermine the Ag-Si phase diagram and calculate the associated thermodynamic properties. EXPERIMENTAL The Ag-Si phase diagram was determined by thermal analysis of liquid alloys. The alloys were contained in a 35 mm alumina crucible under a protective stream of purified argon. The crucible was placed inside a 64 mm alumina tube fitted with a gas-tight, water-cooled, copper head. The tube and assembly were heated in a manually controlled globar furnace. The temperature was measured with a Pt, Pt + 10 pct Rh thermocouple in a high-temperature porcelain protection tube. The thermocouple calibration4 was checked against the melting point of pure silver at the start and during the course of the experiments, and against both gold and silver at the completion of the experiments. The alloys were prepared from granular silver analyzing 99.95 pct Ag and powdered silicon analyzing 99.88 pct Si and 0.026 pct Fe. Approximately 150 g of alloy were used for each run. The composition of the alloy was determined by withdrawing samples of the liquid alloy with a vycor tube-aspirator bulb device. Analysis of solidified samples agreed, for alloys containing less than 23 pct Si, within ±0.3 pct Si of the calculated composition. Duplicate samples showed a variance within 50.05 pct Si of the mean analysis. The alloy was heated to 100' to 20pC above the estimated liquidus temperature and then the furnace was adjusted to give an average cooling rate of 2" to 7°C per min. A cooling curve was obtained by taking potentiometer readings at 15-sec intervals. Several analyses were made by recording the thermocouple output on a high-speed, Stip-chart recorder, with the exception of run NO. 11, a minimum of two thermal analyses were made for each alloy and the cooling curves then obtained duplicated the liquidus and eutectic temperatures to about 1°C. RESULTS The results of the thermal analysis are given in Table 1, and are represented as the Ag-Si phase dlagram, Fig. 1. The eutectic composition was found

Jan 1, 1963

By Junius D. Edwards

WHEN Charles Martin Hall invented the electrolytic process for the production of aluminum, one basic requirement was a supply of pure alumina. Now, more than 50 years later, the same requirement still holds, and there are no technical straws in the wind to indicate that this situation is likely to change. Long ago, Aluminum Company of America took a number of steps to see that this country should not face shortages of alumina and aluminum in time of emergency. As one step to this end, the Company developed and used a supply of bauxite in South America in order to conserve dwindling Arkansas reserves. Another, and more a program than a step, was to investigate every type of process that might bear the possibility of utilizing the low-grade ores of aluminum that are more plentiful than bauxite. It is a long story, but the investigation included electric-furnace processes, acid extraction processes and alkaline extraction processes, with or without preliminary furnace and sinter treatments. Some of the processes developed were operated in commercial production. This work has been continuous since the first World War. The turn of the wheel came sooner than was expected when, in 1942, bauxite shipments through the Caribbean became uncertain and hazardous through the operation of submarines. The tremendous requirements of aluminum for the war effort were consuming high-grade bauxite at an alarming rate and a national search for substitutes began. High-grade bauxites, for technical and economic reasons, have been defined as those containing about 7 per cent or less of silica. While bauxite of this grade was limited in amount in the United States, there was in sight a substantially greater volume of low-grade, high-silica bauxite not amenable to economic treatment by the Bayer process, but richer in alumina than the clays or other available low-grade ores. It was at this point, and after several years of intensive research on this particular phase of the problem, that Aluminum Research Laboratories brought to completion the invention of one of its research staff, which made practical the utilization of large reserves of low-grade bauxite in America. BAYER PROCESS The Bayer process has been almost universally used for the 'production of alumina from bauxite. This process, in outline, comprises the digestion of finely ground bauxite in a solution of caustic soda (NaOH) under pressure and at an elevated temperature. Alumina in the bauxite goes into solution as sodium aluminate and the impurities-oxides of iron, titanium and silicon-remain undissolved. The undissolved residue, known as "red mud," from its color, is separated and run to waste. Aluminum hydrate (A1202.3H20) is precipitated from the solution of sodium aluminate, and the liquor containing the caustic soda and some alumina is returned to the process for digesting more bauxite. The aluminum hydrate, after washing, is calcined at a high temperature to produce

Jan 1, 1945

By John Mills

THREE case histories from professions other than engineering will serve to introduce ideas basic to this discussion. Case (1) Date, about 1900. A young man, B. D. from a three-year graduate course in a prominent divinity school, was for two years a successful pastor of a small church; then friction over theological matters arose with a fundamentalist deacon of the "Bible belt" type. He resigned, returned to his university for a four-year medical course, interned for two more, and thereafter was successful and apparently happy as a physician. We may assume that he was converted in early adolescence and vowed himself to service as a minister. Acceptance of his announced career by parents, friends, and teachers plus his own determination confirmed his choice until illiberal criticism threatened his usefulness and he awoke to the fact that his inner needs were not along the direction in which inertia and his conscience had constrained him.

Jan 1, 1947

By Morton Macartney

FOR many years the developers or owners of worthy mining ventures in need of financing have found it almost impossible to obtain such financing under the conditions existing in most other lines of business. High rates of interest and unfair participation in profits have robbed the developers of much of their holdings, and have resulted in over-capitalization and many other like evils. When the general financial condition of the country is bad, this difficulty increases to a point where many operations must cease and hen are thrown out of employment. In 1.934 this situation had developed to such a point that Congress attempted to aid the mining industry. It first authorized the RFC to make loans to recognized and established corporations, individuals, and partnerships engaged in the business of mining, milling, or smelting of ores in June, 1934, limiting such authority to loans adequately secured, the security to consist of mineral acreage. The requirements of the law were stringent and of the 252 requests for loans received up to June 1, 1935, 35 were authorized.

Jan 1, 1936

By Albert Stazicker

AT Climax the warehouse department operates as an independent unit similar to the mine and mill departments. It has the responsibility of receiving, checking, unloading, and storing all material and supplies delivered to the plant. In addition, the transportation of all supplies comes under the direction of the warehouse so that prompt delivery of supplies to all departments is one of its major functions. The transportation division operates heavy and light trucks, trailers, two large tractors, and two snowplows. In addition to delivering supplies it is also responsible for snow removal from the roads, hauling of sand and gravel for concrete and domestic coal to employees. and all miscellaneous work involving the use of tractors or trucks.

Jan 1, 1946

By B. F. Tillson

Mining may be defined as a general term for the working of valuable deposits of minerals, either organic or inorganic in origin, for their removal from the crust of the earth. Besides subsurface excavations, mining generically includes opencuts, clay pits and stone quarries, oil wells, sulphur wells, salt wells, placers, coal stripping, and the leaching of ore bodies. The origin of the word "mine" or "mining" is a matter of conjecture. A Celtic origin has been suggested since the Irish word mein, or the mwyn, meant ore, but it seems to have come from an olf French verb mineor, which meant to excavate, to make an underground passage as in the military appraoch to a fortification, sometimes called ?sapping.?

Jan 1, 1949

By HAROLD A. KNIGHT

The Miami Copper Co., Arizona, is asking Congress to reimpose the import duty of two cents per pound on copper which, by law, has been suspended until June 30, 1950. C. Donald Dallas, chairman of Revere Copper and Brass, champion of a duty-free regime as regards the red metal, has been answering E. H. Westlake, Miami president, now that Mr. Westlake's statement to stock- holders has been salted away for posterity on wire recorders. Even prior to this action and at the instigation of two prominent consumers of pig lead, the House of Representatives has, in the confines of committee, not yet reported out, as of June 16, a bill to suspend the duty on lead for another year from expiration of the present law June 30, 1949. But apparently the bill was started too late. Thus the tariff issue becomes a Rip Van Winkle again after having slept for several years in the mountains of metals scarcity. During the wartime scarcity and the boom days that followed, most metal producers welcomed a considerable influx of foreign metal since it gave them a little surcease from constant teleibhone calls asking why that delivery of 300 tons of lead, 250 tons of zinc, and 1000 tons of copper had been delayed. These were the days when it was such an undisputed sellers' market that the sellers had even thrown away their certificates of ownership. Another development that brings home the tariff situation, small in it- self but perhaps indicating a trend, has been the announced closing of

Jan 1, 1949

By H. K. Work

The Bessemer process is one of the most interesting methods of making steel. At one time it was by far the most important. In recent years, however, it has steadily lost ground to the open-hearth process. The forces working against this method of stccl-making are partly economic and partly metallurgical.1 In this paper, dealing as it does with the control of the process, the metallurgical factors alone will be considered, although it is obvious that economic factors must play a part in determining the ultimate status of the Bessemer process. This discussion has been limited in another respect—it deals primarily with the acid Bessemer process in bottom-blown converters, although much of the information is applicable to basic and side-blown converters. The fact that open-hearth steel has superseded Ressemer steel to a large extent has tended to create an impression that Bessemer steel is inferior. As a matter of fact, Bessemer steel is actually superior to open-hearth for many applications.2 There are, however, definite metallurgical limitations to the use of Bessemer steel, resulting largely from two factors: (1) the physical properties conferred by nitrogen and phosphorus, and (2) the variability from blow to blow. These, of course, are not entirely independent, since some of the variability covered in the second item is undoubtedly due to nitrogen. But the variability is also caused by other factors. One of these is the relatively small size of the Bessemer heats. Because of this, a given shipment of Bessemer steel is more likely than a shipment of open-hearth steel to contain the product of several heats, each with its own distinctive and slightly different characteristics. Added to this is the fact that the refining of Bessemer steel proceeds so rapidly that the timing of the end point is limited to a matter of seconds, whereas the finishing period in the open hearth extends over a period of one or two hours and the timing of the end point may vary by several minutes without seriously affecting the product. There is no doubt that this has contributed to the variability of Bessemer steel and has led to the use of open-hearth steel in many optional applications. That Bessemer steel may vary is not necessarily objectionable, and it may even prove an advantage, providing a precise control is available to secure the desired qualities for any specific application. With this in mind, a comprehensive research program was undertaken, one phase of which was directed toward securing more accurate control of the blow. The results have been encouraging, and it is the purpose of this paper to describe a method in which modern scientific instruments, based on photocells, are currently being employed to assist the blower. The Control Problem In this day of scientific control of technical processes, where the operating

Jan 1, 1941

By G. A. Croes, N. Schwarz

The dimensionless groups, to which the variables that govern the displacement of oil from reservoirs by liquids can be combined, are derived. Three types of displacement are considered, viz. cold-water drive, hot-water drive and solvent injection. The derivation of the dimerzsionless groups is carried out by means of the relevant basic equations (in-spectional analysis). The resulting sets of groups are afterwards completed by means of dimensional analysis. The form of the groups is given in such a way that they can be adapted to suit the various boundary conditions that are encountered in practice. The physical meaning of the groups is discussed. They have all been brought together on a chart, from which their mutual relation and their corresporzdence to related dimensionless groups in common use in other engineering sciences can be read off. The limitations of dimensionally scaled model experiments as a useful tool for studying liquid flow in porous media, as occurring in oil reservoirs, are discussed. The use of models to study fluid mechanics has an appeal for everyone endowed with natural curiosity. What active boy has not played with ship and airplane models, or crude models of dam and drainage systems Even in the most advanced technical engineering, such models play a fundamental and indispensable role. "And yet in few departments of the physical sciences is there a wider gap between theory and practice, between scientific knowledge and the state of art, than in the use of models to study hydrodynamic phenomena." Garrett Birkhoff1 INTRODUCTION Laboratory displacement experiments are extensively used to investigate, directly or indirectly, the production behavior of petroleum reservoirs. Such experiments are representative of the reservoirs as a whole, if they are carried out with models that are "properly scaled." The performance of oil reservoirs is governed by the values of a number of variables, which can be combined to dimensionless groups. Two general methods are available for the derivation of these groups. In the first of these, dimensional analysis, combination of the variables is done essentially by trial and error. Its only premise is knowledge of the complete set of relevant variables. In the second method, inspectional analysis, the dimensional homogeneity of the equations describing the behavior of the system to be studied is used. The resulting dimensionless groups can be divided into: (a) independent (variable) groups, such as dimensionless length, time, etc.; (b) dependent groups, giving the dimensionless form of the variables, such as recovery and pressure, that can, at least in principle, be measured during an experiment; (c) similarity groups, which are independent constant groups, such as ratio of length to height of the reservoir and ratio of

Jan 1, 1957